Search Results

Search found 38 results on 2 pages for 'hpet'.

Page 1/2 | 1 2  | Next Page >

• HPET for x86 BSP (how to build it for WCE8)

  - by Werner Willemsens

  Originally posted on: http://geekswithblogs.net/WernerWillemsens/archive/2014/08/02/157895.aspx"I needed a timer". That is how we started a few blogs ago our series about APIC and ACPI. Well, here it is. HPET (High Precision Event Timer) was introduced by Intel in early 2000 to: Replace old style Intel 8253 (1981!) and 8254 timers Support more accurate timers that could be used for multimedia purposes. Hence Microsoft and Intel sometimes refers to HPET as Multimedia timers. An HPET chip consists of a 64-bit up-counter (main counter) counting at a frequency of at least 10 MHz, and a set of (at least three, up to 256) comparators. These comparators are 32- or 64-bit wide. The HPET is discoverable via ACPI. The HPET circuit in recent Intel platforms is integrated into the SouthBridge chip (e.g. 82801) All HPET timers should support one-shot interrupt programming, while optionally they can support periodic interrupts. In most Intel SouthBridges I worked with, there are three HPET timers. TIMER0 supports both one-shot and periodic mode, while TIMER1 and TIMER2 are one-shot only. Each HPET timer can generate interrupts, both in old-style PIC mode and in APIC mode. However in PIC mode, interrupts cannot freely be chosen. Typically IRQ11 is available and cannot be shared with any other interrupt! Which makes the HPET in PIC mode virtually unusable. In APIC mode however more IRQs are available and can be shared with other interrupt generating devices. (Check the datasheet of your SouthBridge) Because of this higher level of freedom, I created the APIC BSP (see previous posts). The HPET driver code that I present you here uses this APIC mode. Hpet.reg [HKEY_LOCAL_MACHINE\Drivers\BuiltIn\Hpet] "Dll"="Hpet.dll" "Prefix"="HPT" "Order"=dword:10 "IsrDll"="giisr.dll" "IsrHandler"="ISRHandler" "Priority256"=dword:50 Because HPET does not reside on the PCI bus, but can be found through ACPI as a memory mapped device, you don't need to specify the "Class", "SubClass", "ProgIF" and other PCI related registry keys that you typically find for PCI devices. If a driver needs to run its internal thread(s) at a certain priority level, by convention in Windows CE you add the "Priority256" registry key. Through this key you can easily play with the driver's thread priority for better response and timer accuracy. See later. Hpet.cpp (Hpet.dll) This cpp file contains the complete HPET driver code. The file is part of a folder that you typically integrate in your BSP (\src\drivers\Hpet). It is written as sample (example) code, you most likely want to change this code to your specific needs. There are two sets of #define's that I use to control how the driver works. _TRIGGER_EVENT or _TRIGGER_SEMAPHORE: _TRIGGER_EVENT will let your driver trigger a Windows CE Event when the timer expires, _TRIGGER_SEMAPHORE will trigger a Windows CE counting Semaphore. The latter guarantees that no events get lost in case your application cannot always process the triggers fast enough. _TIMER0 or _TIMER2: both timers will trigger an event or semaphore periodically. _TIMER0 will use a periodic HPET timer interrupt, while _TIMER2 will reprogram a one-shot HPET timer after each interrupt. The one-shot approach is interesting if the frequency you wish to generate is not an even multiple of the HPET main counter frequency. The sample code uses an algorithm to generate a more correct frequency over a longer period (by reducing rounding errors). _TIMER1 is not used in the sample source code. HPT_Init() will locate the HPET I/O memory space, setup the HPET counter (_TIMER0 or _TIMER2) and install the Interrupt Service Thread (IST). Upon timer expiration, the IST will run and on its turn will generate a Windows CE Event or Semaphore. In case of _TIMER2 a new one-shot comparator value is calculated and set for the timer. The IRQ of the HPET timers are programmed to IRQ22, but you can choose typically from 20-23. The TIMERn_INT_ROUT_CAP bits in the TIMn_CONF register will tell you what IRQs you can choose from. HPT_IOControl() can be used to set a new HPET counter frequency (actually you configure the counter timeout value in microseconds), start and stop the timer, and request the current HPET counter value. The latter is interesting because the Windows CE QueryPerformanceCounter() and QueryPerformanceFrequency() APIs implement the same functionality, albeit based on other counter implementations. HpetDrvIst() contains the IST code. DWORD WINAPI HpetDrvIst(LPVOID lpArg) { psHpetDeviceContext pHwContext = (psHpetDeviceContext)lpArg; DWORD mainCount = READDWORD(pHwContext->g_hpet_va, GenCapIDReg + 4); // Main Counter Tick period (fempto sec 10E-15) DWORD i = 0; while (1) { WaitForSingleObject(pHwContext->g_isrEvent, INFINITE); #if defined(_TRIGGER_SEMAPHORE) LONG p = 0; BOOL b = ReleaseSemaphore(pHwContext->g_triggerEvent, 1, &p); #elif defined(_TRIGGER_EVENT) BOOL b = SetEvent(pHwContext->g_triggerEvent); #else #pragma error("Unknown TRIGGER") #endif #if defined(_TIMER0) DWORD currentCount = READDWORD(pHwContext->g_hpet_va, MainCounterReg); DWORD comparator = READDWORD(pHwContext->g_hpet_va, Tim0_ComparatorReg + 0); SETBIT(pHwContext->g_hpet_va, GenIntStaReg, 0); // clear interrupt on HPET level InterruptDone(pHwContext->g_sysIntr); // clear interrupt on OS level _LOGMSG(ZONE_INTERRUPT, (L"%s: HpetDrvIst 0 %06d %08X %08X", pHwContext->g_id, i++, currentCount, comparator)); #elif defined(_TIMER2) DWORD currentCount = READDWORD(pHwContext->g_hpet_va, MainCounterReg); DWORD previousComparator = READDWORD(pHwContext->g_hpet_va, Tim2_ComparatorReg + 0); pHwContext->g_counter2.QuadPart += pHwContext->g_comparator.QuadPart; // increment virtual counter (higher accuracy) DWORD comparator = (DWORD)(pHwContext->g_counter2.QuadPart >> 8); // "round" to real value WRITEDWORD(pHwContext->g_hpet_va, Tim2_ComparatorReg + 0, comparator); SETBIT(pHwContext->g_hpet_va, GenIntStaReg, 2); // clear interrupt on HPET level InterruptDone(pHwContext->g_sysIntr); // clear interrupt on OS level _LOGMSG(ZONE_INTERRUPT, (L"%s: HpetDrvIst 2 %06d %08X %08X (%08X)", pHwContext->g_id, i++, currentCount, comparator, comparator - previousComparator)); #else #pragma error("Unknown TIMER") #endif } return 1; } The following figure shows how the HPET hardware interrupt via ISR -> IST is translated in a Windows CE Event or Semaphore by the HPET driver. The Event or Semaphore can be used to trigger a Windows CE application. HpetTest.cpp (HpetTest.exe)This cpp file contains sample source how to use the HPET driver from an application. The file is part of a separate (smart device) VS2013 solution. It contains code to measure the generated Event/Semaphore times by means of GetSystemTime() and QueryPerformanceCounter() and QueryPerformanceFrequency() APIs. HPET evaluation If you scan the internet about HPET, you'll find many remarks about buggy HPET implementations and bad performance. Unfortunately that is true. I tested the HPET driver on an Intel ICH7M SBC (release date 2008). When a HPET timer expires on the ICH7M, an interrupt indeed is generated, but right after you clear the interrupt, a few more unwanted interrupts (too soon!) occur as well. I tested and debugged it for a loooong time, but I couldn't get it to work. I concluded ICH7M's HPET is buggy Intel hardware. I tested the HPET driver successfully on a more recent NM10 SBC (release date 2013). With the NM10 chipset however, I am not fully convinced about the timer's frequency accuracy. In the long run - on average - all is fine, but occasionally I experienced upto 20 microseconds delays (which were immediately compensated on the next interrupt). Of course, this was all measured by software, but I still experienced the occasional delay when both the HPET driver IST thread as the application thread ran at CeSetThreadPriority(1). If it is not the hardware, only the kernel can cause this delay. But Windows CE is an RTOS and I have never experienced such long delays with previous versions of Windows CE. I tested and developed this on WCE8, I am not heavily experienced with it yet. Internet forum threads however mention inaccurate HPET timer implementations as well. At this moment I haven't figured out what is going on here. Useful references: http://www.intel.com/content/dam/www/public/us/en/documents/technical-specifications/software-developers-hpet-spec-1-0a.pdf http://en.wikipedia.org/wiki/High_Precision_Event_Timer http://wiki.osdev.org/HPET Windows CE BSP source file package for HPET in MyBsp Note that this source code is "As Is". It is still under development and I cannot (and never will) guarantee the correctness of the code. Use it as a guide for your own HPET integration.

  Read the article

• HPET missing from available clocksources on CentOS

  - by squareone

  I am having trouble using HPET on my physical machine. It is not available, even though I have enabled it in my bios, forced it in grub, and triple checked my kernel to include HPET in its compilation. Motherboard: Supermicro X9DRW Processor: 2x Intel(R) Xeon(R) CPU E5-2640 SAS Controller: LSI Logic / Symbios Logic SAS2004 PCI-Express Fusion-MPT SAS-2 [Spitfire] (rev 03) Distro: CentOS 6.3 Kernel: 3.4.21-rt32 #2 SMP PREEMPT RT x86_64 GNU/Linux Grub: hpet=force clocksource=hpet .config file: CONFIG_HPET_TIMER=y CONFIG_HPET_EMULATE_RTC=y CONFIG_HPET=y dmesg | grep hpet: Command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet Kernel command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet cat /sys/devices/system/clocksource/clocksource0/current_clocksource: tsc cat /sys/devices/system/clocksource/clocksource0/available_clocksource: tsc jiffies What is even more confusing, is that I have about a dozen other machines that utilize the same kernel .config, and can use HPET fine. I fear it is a hardware issue, but would appreciate any advice or help with getting HPET available. Thanks in advance!

  Read the article

• AHCI, Power Mode S3 and HPET 64bit - please help with these settings!

  - by thetattoo

  my problem is the that for a Hackintosh (unofficial PC running OS X) I needed to set AHCI, Power Mode S3 and HPET 64bit. Now, I want to install Ubuntu (when 12.04 comes out) and was wondering if these settings will be right to use for Ubuntu. I read that AHCI is how the hard disks are accessed, Power Mode S3 is how suspend works with the RAM but couldn't figure out if using HPET 64bit makes any difference than HPET 32bit. What I would like is an explanation of what these BIOS settings do and what is best for Ubuntu. Thank you very much

  Read the article

• FreeBSD performance tuning. Sysctls, loader.conf, kernel

  - by SaveTheRbtz

  I wanted to share knowledge of tuning FreeBSD via sysctl.conf/loader.conf/KENCONF. It was initially based on Igor Sysoev's (author of nginx) presentation about FreeBSD tuning up to 100,000-200,000 active connections. Tunings are for FreeBSD-CURRENT. Since 7.2 amd64 some of them are tuned well by default. Prior 7.0 some of them are boot only (set via /boot/loader.conf) or does not exist at all. sysctl.conf: # No zero mapping feature # May break wine # (There are also reports about broken samba3) #security.bsd.map_at_zero=0 # If you have really busy webserver with apache13 you may run out of processes #kern.maxproc=10000 # Same for servers with apache2 / Pound #kern.threads.max_threads_per_proc=4096 # Max. backlog size kern.ipc.somaxconn=4096 # Shared memory // 7.2+ can use shared memory > 2Gb kern.ipc.shmmax=2147483648 # Sockets kern.ipc.maxsockets=204800 # Can cause this on older kernels: # http://old.nabble.com/Significant-performance-regression-for-increased-maxsockbuf-on-8.0-RELEASE-tt26745981.html#a26745981 ) kern.ipc.maxsockbuf=10485760 # Mbuf 2k clusters (on amd64 7.2+ 25600 is default) # For such high value vm.kmem_size must be increased to 3G kern.ipc.nmbclusters=262144 # Jumbo pagesize(_SC_PAGESIZE) clusters # Used as general packet storage for jumbo frames # can be monitored via `netstat -m` #kern.ipc.nmbjumbop=262144 # Jumbo 9k/16k clusters # If you are using them #kern.ipc.nmbjumbo9=65536 #kern.ipc.nmbjumbo16=32768 # For lower latency you can decrease scheduler's maximum time slice # default: stathz/10 (~ 13) #kern.sched.slice=1 # Increase max command-line length showed in `ps` (e.g for Tomcat/Java) # Default is PAGE_SIZE / 16 or 256 on x86 # This avoids commands to be presented as [executable] in `ps` # For more info see: http://www.freebsd.org/cgi/query-pr.cgi?pr=120749 kern.ps_arg_cache_limit=4096 # Every socket is a file, so increase them kern.maxfiles=204800 kern.maxfilesperproc=200000 kern.maxvnodes=200000 # On some systems HPET is almost 2 times faster than default ACPI-fast # Useful on systems with lots of clock_gettime / gettimeofday calls # See http://old.nabble.com/ACPI-fast-default-timecounter,-but-HPET-83--faster-td23248172.html # After revision 222222 HPET became default: http://svnweb.freebsd.org/base?view=revision&revision=222222 kern.timecounter.hardware=HPET # Small receive space, only usable on http-server, on file server this # should be increased to 65535 or even more #net.inet.tcp.recvspace=8192 # This is useful on Fat-Long-Pipes #net.inet.tcp.recvbuf_max=10485760 #net.inet.tcp.recvbuf_inc=65535 # Small send space is useful for http servers that serve small files # Autotuned since 7.x net.inet.tcp.sendspace=16384 # This is useful on Fat-Long-Pipes #net.inet.tcp.sendbuf_max=10485760 #net.inet.tcp.sendbuf_inc=65535 # Turn off receive autotuning # You can play with it. #net.inet.tcp.recvbuf_auto=0 #net.inet.tcp.sendbuf_auto=0 # This should be enabled if you going to use big spaces (>64k) # Also timestamp field is useful when using syncookies net.inet.tcp.rfc1323=1 # Turn this off on high-speed, lossless connections (LAN 1Gbit+) # If you set it there is no need in TCP_NODELAY sockopt (see man tcp) net.inet.tcp.delayed_ack=0 # This feature is useful if you are serving data over modems, Gigabit Ethernet, # or even high speed WAN links (or any other link with a high bandwidth delay product), # especially if you are also using window scaling or have configured a large send window. # Automatically disables on small RTT ( http://www.freebsd.org/cgi/cvsweb.cgi/src/sys/netinet/tcp_subr.c?#rev1.237 ) # This sysctl was removed in 10-CURRENT: # See: http://www.mail-archive.com/[email protected]/msg06178.html #net.inet.tcp.inflight.enable=0 # TCP slowstart algorithm tunings # We assuming we have very fast clients #net.inet.tcp.slowstart_flightsize=100 #net.inet.tcp.local_slowstart_flightsize=100 # Disable randomizing of ports to avoid false RST # Before usage check SA here www.bsdcan.org/2006/papers/ImprovingTCPIP.pdf # (it's also says that port randomization auto-disables at some conn.rates, but I didn't checked it thou) #net.inet.ip.portrange.randomized=0 # Increase portrange # For outgoing connections only. Good for seed-boxes and ftp servers. net.inet.ip.portrange.first=1024 net.inet.ip.portrange.last=65535 # # stops route cache degregation during a high-bandwidth flood # http://www.freebsd.org/doc/en/books/handbook/securing-freebsd.html #net.inet.ip.rtexpire=2 net.inet.ip.rtminexpire=2 net.inet.ip.rtmaxcache=1024 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # # There is also good example of sysctl.conf with comments: # http://www.thern.org/projects/sysctl.conf # # icmp may NOT rst, helpful for those pesky spoofed # icmp/udp floods that end up taking up your outgoing # bandwidth/ifqueue due to all that outgoing RST traffic. # #net.inet.tcp.icmp_may_rst=0 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # IPv6 Security # For more info see http://www.fosslc.org/drupal/content/security-implications-ipv6 # Disable Node info replies # To see this vulnerability in action run `ping6 -a sglAac ::1` or `ping6 -w ::1` on unprotected node net.inet6.icmp6.nodeinfo=0 # Turn on IPv6 privacy extensions # For more info see proposal http://unix.derkeiler.com/Mailing-Lists/FreeBSD/net/2008-06/msg00103.html net.inet6.ip6.use_tempaddr=1 net.inet6.ip6.prefer_tempaddr=1 # Disable ICMP redirect net.inet6.icmp6.rediraccept=0 # Disable acceptation of RA and auto linklocal generation if you don't use them #net.inet6.ip6.accept_rtadv=0 #net.inet6.ip6.auto_linklocal=0 # Increases default TTL, sometimes useful # Default is 64 net.inet.ip.ttl=128 # Lessen max segment life to conserve resources # ACK waiting time in miliseconds # (default: 30000. RFC from 1979 recommends 120000) net.inet.tcp.msl=5000 # Max bumber of timewait sockets net.inet.tcp.maxtcptw=200000 # Don't use tw on local connections # As of 15 Apr 2009. Igor Sysoev says that nolocaltimewait has some buggy realization. # So disable it or now till get fixed #net.inet.tcp.nolocaltimewait=1 # FIN_WAIT_2 state fast recycle net.inet.tcp.fast_finwait2_recycle=1 # Time before tcp keepalive probe is sent # default is 2 hours (7200000) #net.inet.tcp.keepidle=60000 # Should be increased until net.inet.ip.intr_queue_drops is zero net.inet.ip.intr_queue_maxlen=4096 # Interrupt handling via multiple CPU, but with context switch. # You can play with it. Default is 1; #net.isr.direct=0 # This is for routers only #net.inet.ip.forwarding=1 #net.inet.ip.fastforwarding=1 # This speed ups dummynet when channel isn't saturated net.inet.ip.dummynet.io_fast=1 # Increase dummynet(4) hash #net.inet.ip.dummynet.hash_size=2048 #net.inet.ip.dummynet.max_chain_len # Should be increased when you have A LOT of files on server # (Increase until vfs.ufs.dirhash_mem becomes lower) vfs.ufs.dirhash_maxmem=67108864 # Note from commit http://svn.freebsd.org/base/head@211031 : # For systems with RAID volumes and/or virtualization envirnments, where # read performance is very important, increasing this sysctl tunable to 32 # or even more will demonstratively yield additional performance benefits. vfs.read_max=32 # Explicit Congestion Notification (see http://en.wikipedia.org/wiki/Explicit_Congestion_Notification) net.inet.tcp.ecn.enable=1 # Flowtable - flow caching mechanism # Useful for routers #net.inet.flowtable.enable=1 #net.inet.flowtable.nmbflows=65535 # Extreme polling tuning #kern.polling.burst_max=1000 #kern.polling.each_burst=1000 #kern.polling.reg_frac=100 #kern.polling.user_frac=1 #kern.polling.idle_poll=0 # IPFW dynamic rules and timeouts tuning # Increase dyn_buckets till net.inet.ip.fw.curr_dyn_buckets is lower net.inet.ip.fw.dyn_buckets=65536 net.inet.ip.fw.dyn_max=65536 net.inet.ip.fw.dyn_ack_lifetime=120 net.inet.ip.fw.dyn_syn_lifetime=10 net.inet.ip.fw.dyn_fin_lifetime=2 net.inet.ip.fw.dyn_short_lifetime=10 # Make packets pass firewall only once when using dummynet # i.e. packets going thru pipe are passing out from firewall with accept #net.inet.ip.fw.one_pass=1 # shm_use_phys Wires all shared pages, making them unswappable # Use this to lessen Virtual Memory Manager's work when using Shared Mem. # Useful for databases #kern.ipc.shm_use_phys=1 # ZFS # Enable prefetch. Useful for sequential load type i.e fileserver. # FreeBSD sets vfs.zfs.prefetch_disable to 1 on any i386 systems and # on any amd64 systems with less than 4GB of avaiable memory # For additional info check this nabble thread http://old.nabble.com/Samba-read-speed-performance-tuning-td27964534.html #vfs.zfs.prefetch_disable=0 # On highload servers you may notice following message in dmesg: # "Approaching the limit on PV entries, consider increasing either the # vm.pmap.shpgperproc or the vm.pmap.pv_entry_max tunable" vm.pmap.shpgperproc=2048 loader.conf: # Accept filters for data, http and DNS requests # Useful when your software uses select() instead of kevent/kqueue or when you under DDoS # DNS accf available on 8.0+ accf_data_load="YES" accf_http_load="YES" accf_dns_load="YES" # Async IO system calls aio_load="YES" # Linux specific devices in /dev # As for 8.1 it only /dev/full #lindev_load="YES" # Adds NCQ support in FreeBSD # WARNING! all ad[0-9]+ devices will be renamed to ada[0-9]+ # 8.0+ only #ahci_load="YES" #siis_load="YES" # FreeBSD 8.2+ # New Congestion Control for FreeBSD # http://caia.swin.edu.au/urp/newtcp/tools/cc_chd-readme-0.1.txt # http://www.ietf.org/proceedings/78/slides/iccrg-5.pdf # Initial merge commit message http://www.mail-archive.com/[email protected]/msg31410.html #cc_chd_load="YES" # Increase kernel memory size to 3G. # # Use ONLY if you have KVA_PAGES in kernel configuration, and you have more than 3G RAM # Otherwise panic will happen on next reboot! # # It's required for high buffer sizes: kern.ipc.nmbjumbop, kern.ipc.nmbclusters, etc # Useful on highload stateful firewalls, proxies or ZFS fileservers # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #vm.kmem_size="3G" # If your server has lots of swap (>4Gb) you should increase following value # according to http://lists.freebsd.org/pipermail/freebsd-hackers/2009-October/029616.html # Otherwise you'll be getting errors # "kernel: swap zone exhausted, increase kern.maxswzone" # kern.maxswzone="256M" # Older versions of FreeBSD can't tune maxfiles on the fly #kern.maxfiles="200000" # Useful for databases # Sets maximum data size to 1G # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #kern.maxdsiz="1G" # Maximum buffer size(vfs.maxbufspace) # You can check current one via vfs.bufspace # Should be lowered/upped depending on server's load-type # Usually decreased to preserve kmem # (default is 10% of mem) #kern.maxbcache="512M" # Sendfile buffers # For i386 only #kern.ipc.nsfbufs=10240 # FreeBSD 9+ # HPET "legacy route" support. It should allow HPET to work per-CPU # See http://www.mail-archive.com/[email protected]/msg03603.html #hint.atrtc.0.clock=0 #hint.attimer.0.clock=0 #hint.hpet.0.legacy_route=1 # syncache Hash table tuning net.inet.tcp.syncache.hashsize=1024 net.inet.tcp.syncache.bucketlimit=512 net.inet.tcp.syncache.cachelimit=65536 # Increased hostcache # Later host cache can be viewed via net.inet.tcp.hostcache.list hidden sysctl # Very useful for it's RTT RTTVAR # Must be power of two net.inet.tcp.hostcache.hashsize=65536 # hashsize * bucketlimit (which is 30 by default) # It allocates 255Mb (1966080*136) of RAM net.inet.tcp.hostcache.cachelimit=1966080 # TCP control-block Hash table tuning net.inet.tcp.tcbhashsize=4096 # Disable ipfw deny all # Should be uncommented when there is a chance that # kernel and ipfw binary may be out-of sync on next reboot #net.inet.ip.fw.default_to_accept=1 # # SIFTR (Statistical Information For TCP Research) is a kernel module that # logs a range of statistics on active TCP connections to a log file. # See prerelease notes http://groups.google.com/group/mailing.freebsd.current/browse_thread/thread/b4c18be6cdce76e4 # and man 4 sitfr #siftr_load="YES" # Enable superpages, for 7.2+ only # Also read http://lists.freebsd.org/pipermail/freebsd-hackers/2009-November/030094.html vm.pmap.pg_ps_enabled=1 # Usefull if you are using Intel-Gigabit NIC #hw.em.rxd=4096 #hw.em.txd=4096 #hw.em.rx_process_limit="-1" # Also if you have ALOT interrupts on NIC - play with following parameters # NOTE: You should set them for every NIC #dev.em.0.rx_int_delay: 250 #dev.em.0.tx_int_delay: 250 #dev.em.0.rx_abs_int_delay: 250 #dev.em.0.tx_abs_int_delay: 250 # There is also multithreaded version of em/igb drivers can be found here: # http://people.yandex-team.ru/~wawa/ # # for additional em monitoring and statistics use # sysctl dev.em.0.stats=1 ; dmesg # sysctl dev.em.0.debug=1 ; dmesg # Also after r209242 (-CURRENT) there is a separate sysctl for each stat variable; # Same tunings for igb #hw.igb.rxd=4096 #hw.igb.txd=4096 #hw.igb.rx_process_limit=100 # Some useful netisr tunables. See sysctl net.isr #net.isr.maxthreads=4 #net.isr.defaultqlimit=4096 #net.isr.maxqlimit: 10240 # Bind netisr threads to CPUs #net.isr.bindthreads=1 # # FreeBSD 9.x+ # Increase interface send queue length # See commit message http://svn.freebsd.org/viewvc/base?view=revision&revision=207554 #net.link.ifqmaxlen=1024 # Nicer boot logo =) loader_logo="beastie" And finally here is KERNCONF: # Just some of them, see also # cat /sys/{i386,amd64,}/conf/NOTES # This one useful only on i386 #options KVA_PAGES=512 # You can play with HZ in environments with high interrupt rate (default is 1000) # 100 is for my notebook to prolong it's battery life #options HZ=100 # Polling is goot on network loads with high packet rates and low-end NICs # NB! Do not enable it if you want more than one netisr thread #options DEVICE_POLLING # Eliminate datacopy on socket read-write # To take advantage with zero copy sockets you should have an MTU >= 4k # This req. is only for receiving data. # Read more in man zero_copy_sockets # Also this epic thread on kernel trap: # http://kerneltrap.org/node/6506 # Here Linus says that "anybody that does it that way (FreeBSD) is totally incompetent" #options ZERO_COPY_SOCKETS # Support TCP sign. Used for IPSec options TCP_SIGNATURE # There was stackoverflow found in KAME IPSec stack: # See http://secunia.com/advisories/43995/ # For quick workaround you can use `ipfw add deny proto ipcomp` options IPSEC # This ones can be loaded as modules. They described in loader.conf section #options ACCEPT_FILTER_DATA #options ACCEPT_FILTER_HTTP # Adding ipfw, also can be loaded as modules options IPFIREWALL # On 8.1+ you can disable verbose to see blocked packets on ipfw0 interface. # Also there is no point in compiling verbose into the kernel, because # now there is net.inet.ip.fw.verbose tunable. #options IPFIREWALL_VERBOSE #options IPFIREWALL_VERBOSE_LIMIT=10 options IPFIREWALL_FORWARD # Adding kernel NAT options IPFIREWALL_NAT options LIBALIAS # Traffic shaping options DUMMYNET # Divert, i.e. for userspace NAT options IPDIVERT # This is for OpenBSD's pf firewall device pf device pflog # pf's QoS - ALTQ options ALTQ options ALTQ_CBQ # Class Bases Queuing (CBQ) options ALTQ_RED # Random Early Detection (RED) options ALTQ_RIO # RED In/Out options ALTQ_HFSC # Hierarchical Packet Scheduler (HFSC) options ALTQ_PRIQ # Priority Queuing (PRIQ) options ALTQ_NOPCC # Required for SMP build # Pretty console # Manual can be found here http://forums.freebsd.org/showthread.php?t=6134 #options VESA #options SC_PIXEL_MODE # Disable reboot on Ctrl Alt Del #options SC_DISABLE_REBOOT # Change normal|kernel messages color options SC_NORM_ATTR=(FG_GREEN|BG_BLACK) options SC_KERNEL_CONS_ATTR=(FG_YELLOW|BG_BLACK) # More scroll space options SC_HISTORY_SIZE=8192 # Adding hardware crypto device device crypto device cryptodev # Useful network interfaces device vlan device tap #Virtual Ethernet driver device gre #IP over IP tunneling device if_bridge #Bridge interface device pfsync #synchronization interface for PF device carp #Common Address Redundancy Protocol device enc #IPsec interface device lagg #Link aggregation interface device stf #IPv4-IPv6 port # Also for my notebook, but may be used with Opteron device amdtemp # Same for Intel processors device coretemp # man 4 cpuctl device cpuctl # CPU control pseudo-device # Support for ECMP. More than one route for destination # Works even with default route so one can use it as LB for two ISP # For now code is unstable and panics (panic: rtfree 2) on route deletions. #options RADIX_MPATH # Multicast routing #options MROUTING #options PIM # Debug & DTrace options KDB # Kernel debugger related code options KDB_TRACE # Print a stack trace for a panic options KDTRACE_FRAME # amd64-only(?) options KDTRACE_HOOKS # all architectures - enable general DTrace hooks #options DDB #options DDB_CTF # all architectures - kernel ELF linker loads CTF data # Adaptive spining in lockmgr (8.x+) # See http://www.mail-archive.com/[email protected]/msg10782.html options ADAPTIVE_LOCKMGRS # UTF-8 in console (8.x+) #options TEKEN_UTF8 # FreeBSD 8.1+ # Deadlock resolver thread # For additional information see http://www.mail-archive.com/[email protected]/msg18124.html # (FYI: "resolution" is panic so use with caution) #options DEADLKRES # Increase maximum size of Raw I/O and sendfile(2) readahead #options MAXPHYS=(1024*1024) #options MAXBSIZE=(1024*1024) # For scheduler debug enable following option. # Debug will be available via `kern.sched.stats` sysctl # For more information see http://svnweb.freebsd.org/base/head/sys/conf/NOTES?view=markup #options SCHED_STATS If you are tuning network for maximum performance you may wish to play with ifconfig options like: # You can list all capabilities via `ifconfig -m` ifconfig [-]rxcsum [-]txcsum [-]tso [-]lro mtu In case you've enabled DDB in kernel config, you should edit your /etc/ddb.conf and add something like this to enable automatic reboot (and textdump as bonus): script kdb.enter.panic=textdump set; capture on; show pcpu; bt; ps; alltrace; capture off; call doadump; reset script kdb.enter.default=textdump set; capture on; bt; ps; capture off; call doadump; reset And do not forget to add ddb_enable="YES" to /etc/rc.conf Since FreeBSD 9 you can select to enable/disable flowcontrol on your NIC: # See http://en.wikipedia.org/wiki/Ethernet_flow_control and # http://www.mail-archive.com/[email protected]/msg07927.html for additional info ifconfig bge0 media auto mediaopt flowcontrol PS. Also most of FreeBSD's limits can be monitored by # vmstat -z and # limits PPS. variety of network counters can be monitored via # netstat -s In FreeBSD-9 netstat's -Q option appeared, try following command to display netisr stats # netstat -Q PPPS. also see # man 7 tuning PPPPS. I wanted to thank FreeBSD community, especially author of nginx - Igor Sysoev, nginx-ru@ and FreeBSD-performance@ mailing lists for providing useful information about FreeBSD tuning. FreeBSD WIP * Whats cooking for FreeBSD 7? * Whats cooking for FreeBSD 8? * Whats cooking for FreeBSD 9? So here is the question: What tunings are you using on yours FreeBSD servers? You can also post your /etc/sysctl.conf, /boot/loader.conf, kernel options, etc with description of its' meaning (do not copy-paste from sysctl -d). Don't forget to specify server type (web, smb, gateway, etc) Let's share experience!

  Read the article

• Android emulator performance on linux

  - by Rado

  I installed the android SDK and eclipse plugin on my laptop, but I was surprised to find out that the emulator eats up 100% of one of my cpu cores. I have exactly the same setup on a desktop machine that does not have this issue. Both computers are running arch linux and both were updated yesterday. Granted, the desktop has better hardware than the laptop, but I was expecting to get closer to 50% cpu usage than 100% on the laptop. Both android virtual devices have the same specs: CPU: ARM Target: Android 2.3.3 - API Level 10 Skin: WVGA800 SD Card: 512M hw.lcd.density: 240 vm.heapSize: 24 hw.ramSize: 256 Laptop host has Intel Core 2 T7200 @ 2GHz cpu with 2Gb RAM. Desktop host has AMD Phenom II X4 940 @ 3GHz cpu with 8Gb RAM. The android emulator uses only 1 core and here are the CPU usage results: Laptop: Cpu0 : 22.8%us, 76.5%sy, 0.0%ni, 0.3%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu1 : 11.2%us, 2.4%sy, 0.0%ni, 86.4%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 2055484k total, 1860304k used, 195180k free, 5276k buffers Swap: 2000088k total, 106872k used, 1893216k free, 350780k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2026 xyz 20 0 396m 207m 7192 R 100 10.3 4:11.58 emulator-arm Desktop: Cpu0 : 0.7%us, 0.0%sy, 0.0%ni, 99.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 1.3%us, 0.0%sy, 0.0%ni, 98.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 5.0%us, 1.3%sy, 0.0%ni, 91.9%id, 1.7%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 0.3%us, 0.3%sy, 0.0%ni, 99.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 7666324k total, 6506808k used, 1159516k free, 1650960k buffers Swap: 8988348k total, 0k used, 8988348k free, 2867300k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2811 xyz 20 0 392m 220m 6276 S 8 2.9 0:33.58 emulator-arm Is there any way I can improve the emulator performance on the laptop? [UPDATE] I ran the emulator with the same settings, on the same laptop under Win7 and after starting up, it didn't use 100% of a CPU core unlike under linux. Also, I tried running the emulator from a terminal in Linux and I get this message when I don't get it under the desktop Linux host: Could not configure '/dev/hpet' to have a 1024Hz timer. This is not a fatal error, but for better emulation accuracy type: 'echo 1024 /proc/sys/dev/hpet/max-user-freq' as root. I'm not really familiar with rtc or hpet, but it doesn't seem that max-user-freq setting does anything, I still get the same warning.

  Read the article

• how can i find my usb2rs232 driver

  - by mefmef

  i have a device that is correctly connected to my PC . but i could not see it in /dev . what does it means? is it because of not installing my drive? $ /dev ls before connecting my device: agpgart mei sda1 tty28 tty59 ttyS30 autofs mem sda2 tty29 tty6 ttyS31 block net sda5 tty3 tty60 ttyS4 bsg network_latency sda6 tty30 tty61 ttyS5 btrfs-control network_throughput serial tty31 tty62 ttyS6 bus null sg0 tty32 tty63 ttyS7 char oldmem shm tty33 tty7 ttyS8 console parport0 snapshot tty34 tty8 ttyS9 core port snd tty35 tty9 ttyUSB0 cpu ppp stderr tty36 ttyprintk uinput cpu_dma_latency psaux stdin tty37 ttyS0 urandom disk ptmx stdout tty38 ttyS1 usbmon0 dri pts tty tty39 ttyS10 usbmon1 ecryptfs ram0 tty0 tty4 ttyS11 usbmon2 fb0 ram1 tty1 tty40 ttyS12 vcs fd ram10 tty10 tty41 ttyS13 vcs1 full ram11 tty11 tty42 ttyS14 vcs2 fuse ram12 tty12 tty43 ttyS15 vcs3 hidraw0 ram13 tty13 tty44 ttyS16 vcs4 hpet ram14 tty14 tty45 ttyS17 vcs5 input ram15 tty15 tty46 ttyS18 vcs6 kmsg ram2 tty16 tty47 ttyS19 vcsa log ram3 tty17 tty48 ttyS2 vcsa1 loop0 ram4 tty18 tty49 ttyS20 vcsa2 loop1 ram5 tty19 tty5 ttyS21 vcsa3 loop2 ram6 tty2 tty50 ttyS22 vcsa4 loop3 ram7 tty20 tty51 ttyS23 vcsa5 loop4 ram8 tty21 tty52 ttyS24 vcsa6 loop5 ram9 tty22 tty53 ttyS25 vga_arbiter loop6 random tty23 tty54 ttyS26 zero loop7 rfkill tty24 tty55 ttyS27 lp0 rtc tty25 tty56 ttyS28 mapper rtc0 tty26 tty57 ttyS29 mcelog sda tty27 tty58 ttyS3 $ /dev ls after connecting my device: agpgart mei sda1 tty28 tty59 ttyS30 autofs mem sda2 tty29 tty6 ttyS31 block net sda5 tty3 tty60 ttyS4 bsg network_latency sda6 tty30 tty61 ttyS5 btrfs-control network_throughput serial tty31 tty62 ttyS6 bus null sg0 tty32 tty63 ttyS7 char oldmem shm tty33 tty7 ttyS8 console parport0 snapshot tty34 tty8 ttyS9 core port snd tty35 tty9 ttyUSB0 cpu ppp stderr tty36 ttyprintk ttyUSB1 cpu_dma_latency psaux stdin tty37 ttyS0 uinput disk ptmx stdout tty38 ttyS1 urandom dri pts tty tty39 ttyS10 usbmon0 ecryptfs ram0 tty0 tty4 ttyS11 usbmon1 fb0 ram1 tty1 tty40 ttyS12 usbmon2 fd ram10 tty10 tty41 ttyS13 vcs full ram11 tty11 tty42 ttyS14 vcs1 fuse ram12 tty12 tty43 ttyS15 vcs2 hidraw0 ram13 tty13 tty44 ttyS16 vcs3 hpet ram14 tty14 tty45 ttyS17 vcs4 input ram15 tty15 tty46 ttyS18 vcs5 kmsg ram2 tty16 tty47 ttyS19 vcs6 log ram3 tty17 tty48 ttyS2 vcsa loop0 ram4 tty18 tty49 ttyS20 vcsa1 loop1 ram5 tty19 tty5 ttyS21 vcsa2 loop2 ram6 tty2 tty50 ttyS22 vcsa3 loop3 ram7 tty20 tty51 ttyS23 vcsa4 loop4 ram8 tty21 tty52 ttyS24 vcsa5 loop5 ram9 tty22 tty53 ttyS25 vcsa6 loop6 random tty23 tty54 ttyS26 vga_arbiter loop7 rfkill tty24 tty55 ttyS27 zero lp0 rtc tty25 tty56 ttyS28 mapper rtc0 tty26 tty57 ttyS29 mcelog sda tty27 tty58 ttyS3

  Read the article

• error about ACPI _OSC request failed (AE_NOT_FOUND)

  - by Yavuz Maslak

  I have ubuntu server 11.10 64 bit I see an error in kernel.log. This error comes out when the server reboot. some port of grep APCI in kernel.log; Dec 5 09:08:51 www kernel: [ 0.588605] pci0000:00: Requesting ACPI _OSC control (0x1d) Dec 5 09:08:51 www kernel: [ 0.588667] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d Dec 5 09:08:51 www kernel: [ 0.588746] ACPI _OSC control for PCIe not granted, disabling ASPM Which hardware may be cause this error ? root@www:# grep -r ACPI /var/log/kern.log Dec 5 09:08:51 www kernel: [ 0.000000] BIOS-e820: 00000000bf780000 - 00000000bf798000 (ACPI data) Dec 5 09:08:51 www kernel: [ 0.000000] BIOS-e820: 00000000bf798000 - 00000000bf7dc000 (ACPI NVS) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: RSDP 00000000000fb1a0 00014 (v00 ACPIAM) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: RSDT 00000000bf780000 00040 (v01 022410 RSDT1405 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: FACP 00000000bf780200 00084 (v01 022410 FACP1405 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: DSDT 00000000bf7804b0 0C359 (v01 A1279 A1279001 00000001 INTL 20060113) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: FACS 00000000bf798000 00040 Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: APIC 00000000bf780390 000D8 (v01 022410 APIC1405 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: MCFG 00000000bf780470 0003C (v01 022410 OEMMCFG 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: OEMB 00000000bf798040 00072 (v01 022410 OEMB1405 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: HPET 00000000bf78f4b0 00038 (v01 022410 OEMHPET 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: OSFR 00000000bf78f4f0 000B0 (v01 022410 OEMOSFR 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: SSDT 00000000bf798fe0 00363 (v01 DpgPmm CpuPm 00000012 INTL 20060113) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000 Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: PM-Timer IO Port: 0x808 Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000 Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x88] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x89] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x8a] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x8b] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x8c] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x8d] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x8e] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x10] lapic_id[0x8f] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfec8a000] gsi_base[24]) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: IRQ0 used by override. Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: IRQ2 used by override. Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: IRQ9 used by override. Dec 5 09:08:51 www kernel: [ 0.000000] Using ACPI (MADT) for SMP configuration information Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000 Dec 5 09:08:51 www kernel: [ 0.009507] ACPI: Core revision 20110413 Dec 5 09:08:51 www kernel: [ 0.499129] PM: Registering ACPI NVS region at bf798000 (278528 bytes) Dec 5 09:08:51 www kernel: [ 0.500749] ACPI: bus type pci registered Dec 5 09:08:51 www kernel: [ 0.502747] ACPI: EC: Look up EC in DSDT Dec 5 09:08:51 www kernel: [ 0.503788] ACPI: Executed 1 blocks of module-level executable AML code Dec 5 09:08:51 www kernel: [ 0.520435] ACPI: SSDT 00000000bf7980c0 00F20 (v01 DpgPmm P001Ist 00000011 INTL 20060113) Dec 5 09:08:51 www kernel: [ 0.520863] ACPI: Dynamic OEM Table Load: Dec 5 09:08:51 www kernel: [ 0.520990] ACPI: SSDT (null) 00F20 (v01 DpgPmm P001Ist 00000011 INTL 20060113) Dec 5 09:08:51 www kernel: [ 0.521308] ACPI: Interpreter enabled Dec 5 09:08:51 www kernel: [ 0.521366] ACPI: (supports S0 S1 S3 S4 S5) Dec 5 09:08:51 www kernel: [ 0.521611] ACPI: Using IOAPIC for interrupt routing Dec 5 09:08:51 www kernel: [ 0.522622] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources Dec 5 09:08:51 www kernel: [ 0.554150] ACPI: No dock devices found. Dec 5 09:08:51 www kernel: [ 0.554267] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug Dec 5 09:08:51 www kernel: [ 0.555231] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) Dec 5 09:08:51 www kernel: [ 0.588224] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] Dec 5 09:08:51 www kernel: [ 0.588398] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] Dec 5 09:08:51 www kernel: [ 0.588451] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] Dec 5 09:08:51 www kernel: [ 0.588473] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT] Dec 5 09:08:51 www kernel: [ 0.588492] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT] Dec 5 09:08:51 www kernel: [ 0.588512] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] Dec 5 09:08:51 www kernel: [ 0.588540] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE1._PRT] Dec 5 09:08:51 www kernel: [ 0.588559] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE3._PRT] Dec 5 09:08:51 www kernel: [ 0.588579] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE7._PRT] Dec 5 09:08:51 www kernel: [ 0.588605] pci0000:00: Requesting ACPI _OSC control (0x1d) Dec 5 09:08:51 www kernel: [ 0.588667] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d Dec 5 09:08:51 www kernel: [ 0.588746] ACPI _OSC control for PCIe not granted, disabling ASPM Dec 5 09:08:51 www kernel: [ 0.597666] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12 14 *15) Dec 5 09:08:51 www kernel: [ 0.598142] ACPI: PCI Interrupt Link [LNKB] (IRQs *5) Dec 5 09:08:51 www kernel: [ 0.598336] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12 14 15) Dec 5 09:08:51 www kernel: [ 0.598810] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 *10 11 12 14 15) Dec 5 09:08:51 www kernel: [ 0.599284] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 *14 15) Dec 5 09:08:51 www kernel: [ 0.599762] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 6 7 10 11 12 14 15) Dec 5 09:08:51 www kernel: [ 0.600236] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 *7 10 11 12 14 15) Dec 5 09:08:51 www kernel: [ 0.600709] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *4 6 7 10 11 12 14 15) Dec 5 09:08:51 www kernel: [ 0.601931] PCI: Using ACPI for IRQ routing Dec 5 09:08:51 www kernel: [ 0.628146] pnp: PnP ACPI init Dec 5 09:08:51 www kernel: [ 0.628211] ACPI: bus type pnp registered Dec 5 09:08:51 www kernel: [ 0.628417] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) Dec 5 09:08:51 www kernel: [ 0.628859] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) Dec 5 09:08:51 www kernel: [ 0.628915] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) Dec 5 09:08:51 www kernel: [ 0.628951] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active) Dec 5 09:08:51 www kernel: [ 0.628975] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) Dec 5 09:08:51 www kernel: [ 0.629004] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active) Dec 5 09:08:51 www kernel: [ 0.629229] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 5 09:08:51 www kernel: [ 0.629779] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 5 09:08:51 www kernel: [ 0.629849] pnp 00:08: Plug and Play ACPI device, IDs PNP0103 (active) Dec 5 09:08:51 www kernel: [ 0.629901] pnp 00:09: Plug and Play ACPI device, IDs INT0800 (active) Dec 5 09:08:51 www kernel: [ 0.630030] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 5 09:08:51 www kernel: [ 0.630254] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 5 09:08:51 www kernel: [ 0.630304] pnp 00:0c: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) Dec 5 09:08:51 www kernel: [ 0.630359] pnp 00:0d: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active) Dec 5 09:08:51 www kernel: [ 0.630492] system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 5 09:08:51 www kernel: [ 0.630986] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active) Dec 5 09:08:51 www kernel: [ 0.631078] pnp: PnP ACPI: found 16 devices Dec 5 09:08:51 www kernel: [ 0.631135] ACPI: ACPI bus type pnp unregistered Dec 5 09:08:51 www kernel: [ 0.726291] ACPI: Power Button [PWRB] Dec 5 09:08:51 www kernel: [ 0.726452] ACPI: Power Button [PWRF] Dec 5 09:08:51 www kernel: [ 0.726527] ACPI: acpi_idle yielding to intel_idle Dec 7 21:45:22 www kernel: [ 0.000000] BIOS-e820: 00000000bf780000 - 00000000bf798000 (ACPI data) Dec 7 21:45:22 www kernel: [ 0.000000] BIOS-e820: 00000000bf798000 - 00000000bf7dc000 (ACPI NVS) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: RSDP 00000000000fb1a0 00014 (v00 ACPIAM) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: RSDT 00000000bf780000 00040 (v01 022410 RSDT1405 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: FACP 00000000bf780200 00084 (v01 022410 FACP1405 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: DSDT 00000000bf7804b0 0C359 (v01 A1279 A1279001 00000001 INTL 20060113) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: FACS 00000000bf798000 00040 Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: APIC 00000000bf780390 000D8 (v01 022410 APIC1405 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: MCFG 00000000bf780470 0003C (v01 022410 OEMMCFG 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: OEMB 00000000bf798040 00072 (v01 022410 OEMB1405 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: HPET 00000000bf78f4b0 00038 (v01 022410 OEMHPET 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: OSFR 00000000bf78f4f0 000B0 (v01 022410 OEMOSFR 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: SSDT 00000000bf798fe0 00363 (v01 DpgPmm CpuPm 00000012 INTL 20060113) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000 Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: PM-Timer IO Port: 0x808 Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000 Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x88] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x89] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x8a] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x8b] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x8c] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x8d] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x8e] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x10] lapic_id[0x8f] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfec8a000] gsi_base[24]) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: IRQ0 used by override. Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: IRQ2 used by override. Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: IRQ9 used by override. Dec 7 21:45:22 www kernel: [ 0.000000] Using ACPI (MADT) for SMP configuration information Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000 Dec 7 21:45:22 www kernel: [ 0.009505] ACPI: Core revision 20110413 Dec 7 21:45:22 www kernel: [ 0.499203] PM: Registering ACPI NVS region at bf798000 (278528 bytes) Dec 7 21:45:22 www kernel: [ 0.500819] ACPI: bus type pci registered Dec 7 21:45:22 www kernel: [ 0.503121] ACPI: EC: Look up EC in DSDT Dec 7 21:45:22 www kernel: [ 0.504162] ACPI: Executed 1 blocks of module-level executable AML code Dec 7 21:45:22 www kernel: [ 0.520821] ACPI: SSDT 00000000bf7980c0 00F20 (v01 DpgPmm P001Ist 00000011 INTL 20060113) Dec 7 21:45:22 www kernel: [ 0.521247] ACPI: Dynamic OEM Table Load: Dec 7 21:45:22 www kernel: [ 0.521374] ACPI: SSDT (null) 00F20 (v01 DpgPmm P001Ist 00000011 INTL 20060113) Dec 7 21:45:22 www kernel: [ 0.521691] ACPI: Interpreter enabled Dec 7 21:45:22 www kernel: [ 0.521748] ACPI: (supports S0 S1 S3 S4 S5) Dec 7 21:45:22 www kernel: [ 0.521993] ACPI: Using IOAPIC for interrupt routing Dec 7 21:45:22 www kernel: [ 0.523002] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources Dec 7 21:45:22 www kernel: [ 0.554533] ACPI: No dock devices found. Dec 7 21:45:22 www kernel: [ 0.554649] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug Dec 7 21:45:22 www kernel: [ 0.555620] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) Dec 7 21:45:22 www kernel: [ 0.588224] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] Dec 7 21:45:22 www kernel: [ 0.588398] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] Dec 7 21:45:22 www kernel: [ 0.588451] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] Dec 7 21:45:22 www kernel: [ 0.588473] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT] Dec 7 21:45:22 www kernel: [ 0.588492] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT] Dec 7 21:45:22 www kernel: [ 0.588512] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] Dec 7 21:45:22 www kernel: [ 0.588540] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE1._PRT] Dec 7 21:45:22 www kernel: [ 0.588559] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE3._PRT] Dec 7 21:45:22 www kernel: [ 0.588579] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE7._PRT] Dec 7 21:45:22 www kernel: [ 0.588606] pci0000:00: Requesting ACPI _OSC control (0x1d) Dec 7 21:45:22 www kernel: [ 0.588667] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d Dec 7 21:45:22 www kernel: [ 0.588746] ACPI _OSC control for PCIe not granted, disabling ASPM Dec 7 21:45:22 www kernel: [ 0.597661] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12 14 *15) Dec 7 21:45:22 www kernel: [ 0.598137] ACPI: PCI Interrupt Link [LNKB] (IRQs *5) Dec 7 21:45:22 www kernel: [ 0.598331] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12 14 15) Dec 7 21:45:22 www kernel: [ 0.598804] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 *10 11 12 14 15) Dec 7 21:45:22 www kernel: [ 0.599278] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 *14 15) Dec 7 21:45:22 www kernel: [ 0.599756] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 6 7 10 11 12 14 15) Dec 7 21:45:22 www kernel: [ 0.600230] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 *7 10 11 12 14 15) Dec 7 21:45:22 www kernel: [ 0.600704] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *4 6 7 10 11 12 14 15) Dec 7 21:45:22 www kernel: [ 0.601926] PCI: Using ACPI for IRQ routing Dec 7 21:45:22 www kernel: [ 0.624115] pnp: PnP ACPI init Dec 7 21:45:22 www kernel: [ 0.624179] ACPI: bus type pnp registered Dec 7 21:45:22 www kernel: [ 0.624382] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) Dec 7 21:45:22 www kernel: [ 0.624821] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) Dec 7 21:45:22 www kernel: [ 0.624875] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) Dec 7 21:45:22 www kernel: [ 0.624911] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active) Dec 7 21:45:22 www kernel: [ 0.624933] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) Dec 7 21:45:22 www kernel: [ 0.624962] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active) Dec 7 21:45:22 www kernel: [ 0.625186] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 7 21:45:22 www kernel: [ 0.625733] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 7 21:45:22 www kernel: [ 0.625803] pnp 00:08: Plug and Play ACPI device, IDs PNP0103 (active) Dec 7 21:45:22 www kernel: [ 0.625856] pnp 00:09: Plug and Play ACPI device, IDs INT0800 (active) Dec 7 21:45:22 www kernel: [ 0.625984] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 7 21:45:22 www kernel: [ 0.626206] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 7 21:45:22 www kernel: [ 0.626256] pnp 00:0c: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) Dec 7 21:45:22 www kernel: [ 0.626312] pnp 00:0d: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active) Dec 7 21:45:22 www kernel: [ 0.626445] system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 7 21:45:22 www kernel: [ 0.626936] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active) Dec 7 21:45:22 www kernel: [ 0.627027] pnp: PnP ACPI: found 16 devices Dec 7 21:45:22 www kernel: [ 0.627084] ACPI: ACPI bus type pnp unregistered Dec 7 21:45:22 www kernel: [ 0.722086] ACPI: Power Button [PWRB] Dec 7 21:45:22 www kernel: [ 0.722246] ACPI: Power Button [PWRF] Dec 7 21:45:22 www kernel: [ 0.722320] ACPI: acpi_idle yielding to intel_idle

  Read the article

• No audio with headphones, but audio works with integrated speakers

  - by Pedro

  My speakers work correctly, but when I plug in my headphones, they don't work. I am running Ubuntu 10.04. My audio card is Realtek ALC259 My laptop model is a HP G62t a10em In another thread someone fixed a similar issue (headphones work, speakers not) folowing this: sudo vi /etc/modprobe.d/alsa-base.conf (or some other editor instead of Vi) Append the following at the end of the file: alias snd-card-0 snd-hda-intel options snd-hda-intel model=auto Reboot but it doesnt work for me. Before making and changes to alsa, this was the output: alsamixer gives me this: Things I did: followed this HowTo but now no hardware seems to be present (before, there were 2 items listed): Now, alsamixer gives me this: alsamixer: relocation error: alsamixer: symbol snd_mixer_get_hctl, version ALSA_0.9 not defined in file libasound.so.2 with link time reference I guess there was and error in the alsa-driver install so I began reinstalling it. cd alsa-driver* //this works fine// sudo ./configure --with-cards=hda-intel --with-kernel=/usr/src/linux-headers-$(uname -r) //this works fine// sudo make //this doesn't work. see ouput error below// sudo make install Final lines of sudo make: hpetimer.c: In function ‘snd_hpet_open’: hpetimer.c:41: warning: implicit declaration of function ‘hpet_register’ hpetimer.c:44: warning: implicit declaration of function ‘hpet_control’ hpetimer.c:44: error: expected expression before ‘unsigned’ hpetimer.c: In function ‘snd_hpet_close’: hpetimer.c:51: warning: implicit declaration of function ‘hpet_unregister’ hpetimer.c:52: error: invalid use of undefined type ‘struct hpet_task’ hpetimer.c: In function ‘hpetimer_init’: hpetimer.c:88: error: ‘EINVAL’ undeclared (first use in this function) hpetimer.c:99: error: invalid use of undefined type ‘struct hpet_task’ hpetimer.c:100: error: invalid use of undefined type ‘struct hpet_task’ hpetimer.c: At top level: hpetimer.c:121: warning: excess elements in struct initializer hpetimer.c:121: warning: (near initialization for ‘__param_frequency’) hpetimer.c:121: warning: excess elements in struct initializer hpetimer.c:121: warning: (near initialization for ‘__param_frequency’) hpetimer.c:121: warning: excess elements in struct initializer hpetimer.c:121: warning: (near initialization for ‘__param_frequency’) hpetimer.c:121: warning: excess elements in struct initializer hpetimer.c:121: warning: (near initialization for ‘__param_frequency’) hpetimer.c:121: error: extra brace group at end of initializer hpetimer.c:121: error: (near initialization for ‘__param_frequency’) hpetimer.c:121: warning: excess elements in struct initializer hpetimer.c:121: warning: (near initialization for ‘__param_frequency’) make[1]: *** [hpetimer.o] Error 1 make[1]: Leaving directory `/usr/src/alsa/alsa-driver-1.0.9/acore' make: *** [compile] Error 1 And then sudo make install gives me: rm -f /lib/modules/0.0.0/misc/snd*.*o /lib/modules/0.0.0/misc/persist.o /lib/modules/0.0.0/misc/isapnp.o make[1]: Entering directory `/usr/src/alsa/alsa-driver-1.0.9/acore' mkdir -p /lib/modules/0.0.0/misc cp snd-hpet.o snd-page-alloc.o snd-pcm.o snd-timer.o snd.o /lib/modules/0.0.0/misc cp: cannot stat `snd-hpet.o': No such file or directory cp: cannot stat `snd-page-alloc.o': No such file or directory cp: cannot stat `snd-pcm.o': No such file or directory cp: cannot stat `snd-timer.o': No such file or directory cp: cannot stat `snd.o': No such file or directory make[1]: *** [_modinst__] Error 1 make[1]: Leaving directory `/usr/src/alsa/alsa-driver-1.0.9/acore' make: *** [install-modules] Error 1 [SOLUTION] After screwing it all up, someone mentioned why not trying using the packages in Synaptic - so I did. I have reinstalled the following packages and rebooter: -alsa-hda-realtek-ignore-sku-dkms -alsa-modules-2.6.32-25-generic -alsa-source -alsa-utils -linux-backports-modules-alsa-lucid-generic -linux-backports-modules-alsa-lucid-generic-pae -linux-sound-base -(i think i listed them all) After rebooting, the audio worked, both in speakers and headphones. I have no idea which is the package that made my audio work, but it certainly was one of them. [/SOLUTION]

  Read the article

• Programmatically measure size and way-order of L1 and L2 caches

  - by osgx

  How can I measure programmatically (not query the OS, but measure) the size and order of associativity of L1 and L2 caches (data caches)? Assumptions about system: It has L1 and L2 cache (may be L3 too, may be cache sharing), It may have a hardware prefetch unit (just like P4+), It has a stable clocksource (tickcounter or good HPET for gettimeofday). There are no assumptions about OS (it can be Linux, Windows, or something non-standard), and we can't use POSIX queries. Language is C. And compiler optimizations may be disabled.

  Read the article

• Programicaly measure size and way-order of L1 and L2 caches

  - by osgx

  Hello How can I measure programicaly (not query the OS, but measure) the size and order of associativity of L1 and L2 caches (data caches)? Assumtions about system: It has L1 and L2 cache (may be L3 too, may be cache sharing), It may have a hardware prefetch unit (just like P4+), it has a stable clocksource (tickcounter or good HPET for gettimeofday). There are no assumtions about OS (it can be Linux, Windows, smth non-standart), and we can't use posix queries. Language is C. And Compiler optimizations may be disabled.

  Read the article

• Fan running continously on HP Pavillion G6 notebook with 12.04.1 LTS, help please?

  - by Ankit

  Fan is running continously on my HP Pavillion G6 notebook with 12.04.1 LTS. My system specifications are:- Ram: 6Gb Graphics Card:- 1 GB (AMD Raedon 64XX). HDD: 540 GB. Please find a list of ACPI errors logs from dmesg as follows:- buffer@ankit:~$ dmesg | grep ACPI -i [ 0.000000] BIOS-e820: 000000009cebf000 - 000000009cfbf000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000009cfbf000 - 000000009cfff000 (ACPI data) [ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 HPQOEM) [ 0.000000] ACPI: XSDT 000000009cffe120 00084 (v01 HPQOEM SLIC-MPC 00000001 01000013) [ 0.000000] ACPI: FACP 000000009cffc000 000F4 (v04 HPQOEM SLIC-MPC 00000001 MSFT 01000013) [ 0.000000] ACPI: DSDT 000000009cfec000 0C132 (v01 HP 1670 00000000 MSFT 01000013) [ 0.000000] ACPI: FACS 000000009cf6c000 00040 [ 0.000000] ACPI: ASF! 000000009cffd000 000A5 (v32 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: HPET 000000009cffb000 00038 (v01 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: APIC 000000009cffa000 0008C (v02 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: MCFG 000000009cff9000 0003C (v01 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: SLIC 000000009cfeb000 00176 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013) [ 0.000000] ACPI: SSDT 000000009cfea000 00D52 (v01 HP 1670 00001000 MSFT 01000013) [ 0.000000] ACPI: BOOT 000000009cfe8000 00028 (v01 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: ASPT 000000009cfe5000 00034 (v07 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: SSDT 000000009cfe4000 00780 (v01 HP 1670 00003000 INTL 20100121) [ 0.000000] ACPI: SSDT 000000009cfe3000 00996 (v01 HP 1670 00003000 INTL 20100121) [ 0.000000] ACPI: SSDT 000000009cfdd000 0219F (v01 HP 1670 00001000 INTL 20100121) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled) [ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0]) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.005902] ACPI: Core revision 20110623 [ 0.536006] PM: Registering ACPI NVS region at 9cebf000 (1048576 bytes) [ 0.538423] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.538429] ACPI: bus type pci registered [ 0.656088] ACPI: Added _OSI(Module Device) [ 0.656094] ACPI: Added _OSI(Processor Device) [ 0.656098] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.656103] ACPI: Added _OSI(Processor Aggregator Device) [ 0.660335] ACPI: EC: Look up EC in DSDT [ 0.664416] ACPI: Executed 1 blocks of module-level executable AML code [ 0.728303] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 0.729536] ACPI: SSDT 000000009ce70798 00727 (v01 PmRef Cpu0Cst 00003001 INTL 20100121) [ 0.730622] ACPI: Dynamic OEM Table Load: [ 0.730630] ACPI: SSDT (null) 00727 (v01 PmRef Cpu0Cst 00003001 INTL 20100121) [ 0.760829] ACPI: SSDT 000000009ce71a98 00303 (v01 PmRef ApIst 00003000 INTL 20100121) [ 0.761992] ACPI: Dynamic OEM Table Load: [ 0.761998] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20100121) [ 0.792451] ACPI: SSDT 000000009ce6fd98 00119 (v01 PmRef ApCst 00003000 INTL 20100121) [ 0.793521] ACPI: Dynamic OEM Table Load: [ 0.793528] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20100121) [ 0.872981] ACPI: Interpreter enabled [ 0.872992] ACPI: (supports S0 S3 S4 S5) [ 0.873064] ACPI: Using IOAPIC for interrupt routing [ 0.882723] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62 [ 0.883072] ACPI: No dock devices found. [ 0.883084] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.883882] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe]) [ 0.924187] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.924509] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] [ 0.924581] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] [ 0.924659] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT] [ 0.924758] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG0._PRT] [ 0.924973] pci0000:00: Requesting ACPI _OSC control (0x1d) [ 0.925064] pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d [ 0.925069] ACPI _OSC control for PCIe not granted, disabling ASPM [ 0.930212] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 *11 12 14 15) [ 0.930327] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 10 *11 12 14 15) [ 0.930436] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 10 *11 12 14 15) [ 0.930547] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15) [ 0.930655] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled. [ 0.930764] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled. [ 0.930873] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 10 *11 12 14 15) [ 0.930979] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled. [ 0.932142] PCI: Using ACPI for IRQ routing [ 0.967119] pnp: PnP ACPI init [ 0.967151] ACPI: bus type pnp registered [ 0.968356] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 0.968516] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.968586] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active) [ 0.968818] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.968915] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.969206] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.969293] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.969418] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active) [ 0.969528] pnp 00:08: Plug and Play ACPI device, IDs SYN1e3f SYN1e00 SYN0002 PNP0f13 (active) [ 0.969969] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.970574] system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.970617] pnp: PnP ACPI: found 11 devices [ 0.970622] ACPI: ACPI bus type pnp unregistered [ 1.138064] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 1.138331] ACPI: AC Adapter [ACAD] (off-line) [ 1.139068] ACPI: Lid Switch [LID0] [ 1.139176] ACPI: Power Button [PWRB] [ 1.139286] ACPI: Power Button [PWRF] [ 1.144637] ACPI: Thermal Zone [TZ01] (0 C) [ 1.144677] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 1.144693] ACPI: Battery Slot [BAT0] (battery present) [ 1.206926] ACPI: Battery Slot [BAT0] (battery present) [ 13.176993] acpi device:1a: registered as cooling_device4 [ 13.179931] acpi device:1b: registered as cooling_device5 [ 13.180221] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) [ 13.219589] acpi device:20: registered as cooling_device6 [ 13.220851] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 1649.915134] i8042 aux 00:08: wake-up capability disabled by ACPI [ 1649.915147] i8042 kbd 00:07: wake-up capability enabled by ACPI [ 1650.931028] r8169 0000:03:00.0: wake-up capability enabled by ACPI [ 1650.954743] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI [ 1650.978733] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI [ 1651.010950] ACPI: Preparing to enter system sleep state S3 [ 1652.251505] ACPI: Low-level resume complete [ 1652.360953] ACPI: Waking up from system sleep state S3 [ 1652.427581] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI [ 1652.435579] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI [ 1652.437887] r8169 0000:03:00.0: wake-up capability disabled by ACPI [ 1652.506660] i8042 kbd 00:07: wake-up capability disabled by ACPI [ 1661.238234] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [ 1661.238253] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [ 1661.238268] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/psparse-536) [ 3151.784288] i8042 aux 00:08: wake-up capability disabled by ACPI [ 3151.784301] i8042 kbd 00:07: wake-up capability enabled by ACPI [ 3152.797676] r8169 0000:03:00.0: wake-up capability enabled by ACPI [ 3152.821379] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI [ 3152.845367] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI [ 3152.877600] ACPI: Preparing to enter system sleep state S3 [ 3154.313213] ACPI: Low-level resume complete [ 3154.422297] ACPI: Waking up from system sleep state S3 [ 3154.489692] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI [ 3154.497667] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI [ 3154.505947] r8169 0000:03:00.0: wake-up capability disabled by ACPI [ 3154.568985] i8042 kbd 00:07: wake-up capability disabled by ACPI [ 3162.745149] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [ 3162.745168] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [ 3162.745183] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/psparse-536) [ 6775.723501] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [ 6775.723519] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [ 6775.723535] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/psparse-536) [10388.004760] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [10388.004778] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [10388.004801] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/psparse-536) [10723.591930] i8042 aux 00:08: wake-up capability disabled by ACPI [10723.591942] i8042 kbd 00:07: wake-up capability enabled by ACPI [10724.607624] r8169 0000:03:00.0: wake-up capability enabled by ACPI [10724.631349] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI [10724.655339] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI [10724.687572] ACPI: Preparing to enter system sleep state S3 [10726.123176] ACPI: Low-level resume complete [10726.232181] ACPI: Waking up from system sleep state S3 [10726.303653] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI [10726.311648] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI [10726.315734] r8169 0000:03:00.0: wake-up capability disabled by ACPI [10726.379287] i8042 kbd 00:07: wake-up capability disabled by ACPI [10734.393523] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [10734.393542] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [10734.393557] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/ps Continuous sound from the fan is very annoying, any help would highly appreciated.

  Read the article

• Garbled text in Screen [closed]

  - by Prabin Dahal

  The graphical Interface in my system is garbled with some text. At the beginning I thought it was due to java and tomcat that I installed. But after removing java and tomcat, it is still the same. I am using ubuntu server and i have installed xfce desktop environment with oboard softkey I have added my dmesg output to this message. What is the problem here. I am not able to figure it out. Thank you for your help. Prabin [ 0.390936] usbcore: registered new interface driver usbfs [ 0.391006] usbcore: registered new interface driver hub [ 0.391147] usbcore: registered new device driver usb [ 0.391580] PCI: Using ACPI for IRQ routing [ 0.400509] PCI: pci_cache_line_size set to 64 bytes [ 0.400669] reserve RAM buffer: 000000000009ec00 - 000000000009ffff [ 0.400681] reserve RAM buffer: 000000007f597000 - 000000007fffffff [ 0.400699] reserve RAM buffer: 000000007f6f0000 - 000000007fffffff [ 0.401135] NetLabel: Initializing [ 0.401155] NetLabel: domain hash size = 128 [ 0.401168] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.401212] NetLabel: unlabeled traffic allowed by default [ 0.401466] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.401494] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.401520] hpet0: 3 comparators, 64-bit 14.318180 MHz counter [ 0.408228] Switching to clocksource hpet [ 0.434341] AppArmor: AppArmor Filesystem Enabled [ 0.434447] pnp: PnP ACPI init [ 0.434531] ACPI: bus type pnp registered [ 0.434784] pnp 00:00: [bus 00-ff] [ 0.434794] pnp 00:00: [io 0x0cf8-0x0cff] [ 0.434804] pnp 00:00: [io 0x0000-0x0cf7 window] [ 0.434813] pnp 00:00: [io 0x0d00-0xffff window] [ 0.434822] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 0.434831] pnp 00:00: [mem 0x00000000 window] [ 0.434840] pnp 00:00: [mem 0x80000000-0xffffffff window] [ 0.435018] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 0.435526] pnp 00:01: [mem 0xe0000000-0xefffffff] [ 0.435537] pnp 00:01: [mem 0x7f700000-0x7f7fffff] [ 0.435545] pnp 00:01: [mem 0x7f800000-0x7fffffff] [ 0.435554] pnp 00:01: [mem 0xfee00000-0xfeefffff] [ 0.435727] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved [ 0.435754] system 00:01: [mem 0x7f700000-0x7f7fffff] has been reserved [ 0.435775] system 00:01: [mem 0x7f800000-0x7fffffff] has been reserved [ 0.435796] system 00:01: [mem 0xfee00000-0xfeefffff] has been reserved [ 0.435818] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.436233] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436245] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436414] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.436512] pnp 00:03: [io 0x0060] [ 0.436521] pnp 00:03: [io 0x0064] [ 0.436548] pnp 00:03: [irq 1] [ 0.436682] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) [ 0.436825] pnp 00:04: [irq 12] [ 0.436958] pnp 00:04: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active) [ 0.437835] pnp 00:05: [io 0x03f8-0x03ff] [ 0.437861] pnp 00:05: [irq 4] [ 0.437870] pnp 00:05: [dma 0 disabled] [ 0.438142] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439014] pnp 00:06: [io 0x02f8-0x02ff] [ 0.439036] pnp 00:06: [irq 3] [ 0.439045] pnp 00:06: [dma 0 disabled] [ 0.439297] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439346] pnp 00:07: [io 0x0000-0x000f] [ 0.439355] pnp 00:07: [io 0x0081-0x0083] [ 0.439363] pnp 00:07: [io 0x0087] [ 0.439371] pnp 00:07: [io 0x0089-0x008b] [ 0.439380] pnp 00:07: [io 0x008f] [ 0.439388] pnp 00:07: [io 0x00c0-0x00df] [ 0.439563] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.439617] pnp 00:08: [io 0x0070-0x0077] [ 0.439639] pnp 00:08: [irq 8] [ 0.439751] pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.439788] pnp 00:09: [io 0x0061] [ 0.439893] pnp 00:09: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.439977] pnp 00:0a: [io 0x0010-0x001f] [ 0.439986] pnp 00:0a: [io 0x0022-0x003f] [ 0.439994] pnp 00:0a: [io 0x0044-0x005f] [ 0.440055] pnp 00:0a: [io 0x0063] [ 0.440063] pnp 00:0a: [io 0x0065] [ 0.440071] pnp 00:0a: [io 0x0067-0x006f] [ 0.440079] pnp 00:0a: [io 0x0072-0x007f] [ 0.440086] pnp 00:0a: [io 0x0080] [ 0.440094] pnp 00:0a: [io 0x0084-0x0086] [ 0.440102] pnp 00:0a: [io 0x0088] [ 0.440109] pnp 00:0a: [io 0x008c-0x008e] [ 0.440117] pnp 00:0a: [io 0x0090-0x009f] [ 0.440125] pnp 00:0a: [io 0x00a2-0x00bf] [ 0.440133] pnp 00:0a: [io 0x00e0-0x00ef] [ 0.440141] pnp 00:0a: [io 0x04d0-0x04d1] [ 0.440150] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440160] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440168] pnp 00:0a: [io 0x03f4] [ 0.440175] pnp 00:0a: [io 0x03f5] [ 0.440183] pnp 00:0a: [io 0x0374] [ 0.440190] pnp 00:0a: [io 0x0375] [ 0.440405] system 00:0a: [io 0x04d0-0x04d1] has been reserved [ 0.440432] system 00:0a: [io 0x03f4] has been reserved [ 0.440451] system 00:0a: [io 0x03f5] has been reserved [ 0.440469] system 00:0a: [io 0x0374] has been reserved [ 0.440488] system 00:0a: [io 0x0375] has been reserved [ 0.440508] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.440550] pnp 00:0b: [io 0x00f0-0x00ff] [ 0.440572] pnp 00:0b: [irq 13] [ 0.440691] pnp 00:0b: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.440770] pnp 00:0c: [io 0x0810] [ 0.440779] pnp 00:0c: [io 0x0800-0x080f] [ 0.440787] pnp 00:0c: [io 0xffff] [ 0.440947] system 00:0c: [io 0x0810] has been reserved [ 0.440970] system 00:0c: [io 0x0800-0x080f] has been reserved [ 0.440989] system 00:0c: [io 0xffff] has been reserved [ 0.441010] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.441620] pnp 00:0d: [io 0x0900-0x097f] [ 0.441630] pnp 00:0d: [io 0x09c0-0x09ff] [ 0.441639] pnp 00:0d: [io 0x0400-0x043f] [ 0.441647] pnp 00:0d: [io 0x0480-0x04bf] [ 0.441656] pnp 00:0d: [mem 0xfec00000-0xfec85fff] [ 0.441664] pnp 00:0d: [mem 0xfed1c000-0xfed1ffff] [ 0.441673] pnp 00:0d: [mem 0x000c0000-0x000dffff] [ 0.441689] pnp 00:0d: [mem 0x000e0000-0x000effff] [ 0.441697] pnp 00:0d: [mem 0x000f0000-0x000fffff] [ 0.441706] pnp 00:0d: [mem 0xff800000-0xffffffff] [ 0.441911] system 00:0d: [io 0x0900-0x097f] has been reserved [ 0.441935] system 00:0d: [io 0x09c0-0x09ff] has been reserved [ 0.441955] system 00:0d: [io 0x0400-0x043f] has been reserved [ 0.441975] system 00:0d: [io 0x0480-0x04bf] has been reserved [ 0.441997] system 00:0d: [mem 0xfec00000-0xfec85fff] could not be reserved [ 0.442019] system 00:0d: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 0.442040] system 00:0d: [mem 0x000c0000-0x000dffff] could not be reserved [ 0.442061] system 00:0d: [mem 0x000e0000-0x000effff] could not be reserved [ 0.442082] system 00:0d: [mem 0x000f0000-0x000fffff] could not be reserved [ 0.442103] system 00:0d: [mem 0xff800000-0xffffffff] has been reserved [ 0.442126] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.442308] pnp 00:0e: [mem 0xfed00000-0xfed003ff] [ 0.442454] pnp 00:0e: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.442569] pnp 00:0f: [mem 0x7f6f0000-0x7f6fffff] [ 0.442762] system 00:0f: [mem 0x7f6f0000-0x7f6fffff] has been reserved [ 0.442788] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.443360] pnp: PnP ACPI: found 16 devices [ 0.443378] ACPI: ACPI bus type pnp unregistered [ 0.443395] PnPBIOS: Disabled by ACPI PNP [ 0.486106] PCI: max bus depth: 3 pci_try_num: 4 [ 0.486189] pci 0000:00:1c.0: PCI bridge to [bus 01-01] [ 0.486217] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff] [ 0.486241] pci 0000:00:1c.0: bridge window [mem 0xd0100000-0xd01fffff] [ 0.486266] pci 0000:00:1c.0: bridge window [mem 0xff700000-0xff7fffff pref] [ 0.486298] pci 0000:03:01.0: PCI bridge to [bus 04-04] [ 0.486319] pci 0000:03:01.0: bridge window [io 0xd000-0xdfff] [ 0.486348] pci 0000:03:01.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486374] pci 0000:03:01.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486406] pci 0000:03:02.0: PCI bridge to [bus 05-05] [ 0.486444] pci 0000:03:03.0: PCI bridge to [bus 06-06] [ 0.486479] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.486499] pci 0000:02:00.0: bridge window [io 0xd000-0xdfff] [ 0.486522] pci 0000:02:00.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486545] pci 0000:02:00.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486575] pci 0000:00:1c.1: PCI bridge to [bus 02-06] [ 0.486593] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff] [ 0.486615] pci 0000:00:1c.1: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486637] pci 0000:00:1c.1: bridge window [mem 0xff600000-0xff6fffff pref] [ 0.486710] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.486735] pci 0000:00:1c.0: setting latency timer to 64 [ 0.486774] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.486796] pci 0000:00:1c.1: setting latency timer to 64 [ 0.486817] pci 0000:02:00.0: setting latency timer to 64 [ 0.486836] pci 0000:03:01.0: setting latency timer to 64 [ 0.486858] pci 0000:03:02.0: setting latency timer to 64 [ 0.486880] pci 0000:03:03.0: setting latency timer to 64 [ 0.486893] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.486902] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.486912] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.486922] pci_bus 0000:00: resource 7 [mem 0x80000000-0xffffffff] [ 0.486932] pci_bus 0000:01: resource 0 [io 0xe000-0xefff] [ 0.486941] pci_bus 0000:01: resource 1 [mem 0xd0100000-0xd01fffff] [ 0.486951] pci_bus 0000:01: resource 2 [mem 0xff700000-0xff7fffff pref] [ 0.486961] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff] [ 0.486970] pci_bus 0000:02: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.486980] pci_bus 0000:02: resource 2 [mem 0xff600000-0xff6fffff pref] [ 0.486989] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff] [ 0.486998] pci_bus 0000:03: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487008] pci_bus 0000:03: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487018] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff] [ 0.487028] pci_bus 0000:04: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487038] pci_bus 0000:04: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487177] NET: Registered protocol family 2 [ 0.487405] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.488397] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.489792] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.490493] TCP: Hash tables configured (established 131072 bind 65536) [ 0.490525] TCP reno registered [ 0.490551] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.490590] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.490898] NET: Registered protocol family 1 [ 0.490970] pci 0000:00:02.0: Boot video device [ 0.491052] pci 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 0.491092] pci 0000:00:1d.0: PCI INT A disabled [ 0.491134] pci 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.491174] pci 0000:00:1d.1: PCI INT B disabled [ 0.491220] pci 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 0.491259] pci 0000:00:1d.2: PCI INT C disabled [ 0.491307] pci 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 0.864431] Freeing initrd memory: 13820k freed [ 2.088042] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001 [ 2.088207] pci 0000:00:1d.7: PCI INT D disabled [ 2.088267] PCI: CLS 64 bytes, default 64 [ 2.089248] audit: initializing netlink socket (disabled) [ 2.089287] type=2000 audit(1349363630.084:1): initialized [ 2.144783] highmem bounce pool size: 64 pages [ 2.144808] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 2.160057] VFS: Disk quotas dquot_6.5.2 [ 2.160232] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.161716] fuse init (API version 7.17) [ 2.161995] msgmni has been set to 1713 [ 2.162925] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 2.163008] io scheduler noop registered [ 2.163023] io scheduler deadline registered [ 2.163048] io scheduler cfq registered (default) [ 2.163339] pcieport 0000:00:1c.0: setting latency timer to 64 [ 2.163530] pcieport 0000:00:1c.1: setting latency timer to 64 [ 2.163706] pcieport 0000:02:00.0: setting latency timer to 64 [ 2.163873] pcieport 0000:03:01.0: setting latency timer to 64 [ 2.163964] pcieport 0000:03:01.0: irq 40 for MSI/MSI-X [ 2.164193] pcieport 0000:03:02.0: setting latency timer to 64 [ 2.164272] pcieport 0000:03:02.0: irq 41 for MSI/MSI-X [ 2.164453] pcieport 0000:03:03.0: setting latency timer to 64 [ 2.164531] pcieport 0000:03:03.0: irq 42 for MSI/MSI-X [ 2.164783] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt [ 2.164801] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 2.164816] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded [ 2.164853] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt [ 2.164867] pcieport 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 2.164880] pcieport 0000:03:01.0: Signaling PME through PCIe PME interrupt [ 2.164892] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt [ 2.164904] pcieport 0000:03:02.0: Signaling PME through PCIe PME interrupt [ 2.164917] pcieport 0000:03:03.0: Signaling PME through PCIe PME interrupt [ 2.164932] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded [ 2.164988] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 2.165115] pciehp 0000:00:1c.0:pcie04: HPC vendor_id 8086 device_id 8110 ss_vid 8086 ss_did 8119 [ 2.165177] pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded [ 2.165199] pciehp 0000:00:1c.1:pcie04: HPC vendor_id 8086 device_id 8112 ss_vid 8086 ss_did 8119 [ 2.165260] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded [ 2.165290] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 2.165488] intel_idle: MWAIT substates: 0x3020220 [ 2.165508] intel_idle: v0.4 model 0x1C [ 2.165513] intel_idle: lapic_timer_reliable_states 0x2 [ 2.165519] Marking TSC unstable due to TSC halts in idle states deeper than C2 [ 2.165779] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0 [ 2.165855] ACPI: Lid Switch [LID] [ 2.165983] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 [ 2.166005] ACPI: Power Button [PWRB] [ 2.173811] thermal LNXTHERM:00: registered as thermal_zone0 [ 2.173829] ACPI: Thermal Zone [TZ00] (48 C) [ 2.174004] thermal LNXTHERM:01: registered as thermal_zone1 [ 2.174018] ACPI: Thermal Zone [TZ01] (34 C) [ 2.174194] thermal LNXTHERM:02: registered as thermal_zone2 [ 2.174207] ACPI: Thermal Zone [TZ02] (34 C) [ 2.174378] thermal LNXTHERM:03: registered as thermal_zone3 [ 2.174392] ACPI: Thermal Zone [TZ03] (34 C) [ 2.174503] ERST: Table is not found! [ 2.174513] GHES: HEST is not enabled! [ 2.174601] isapnp: Scanning for PnP cards... [ 2.176175] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 2.196702] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.292409] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.528909] isapnp: No Plug & Play device found [ 2.588733] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.624523] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.640702] Linux agpgart interface v0.103 [ 2.645138] brd: module loaded [ 2.647452] loop: module loaded [ 2.648149] pata_acpi 0000:00:1f.1: setting latency timer to 64 [ 2.649238] Fixed MDIO Bus: probed [ 2.649315] tun: Universal TUN/TAP device driver, 1.6 [ 2.649327] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 2.649524] PPP generic driver version 2.4.2 [ 2.649824] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.649884] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 2.649937] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 2.649946] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.650082] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 2.650148] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.654045] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 2.654093] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd02c4000 [ 2.668035] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 2.668392] hub 1-0:1.0: USB hub found [ 2.668413] hub 1-0:1.0: 8 ports detected [ 2.668618] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.668666] uhci_hcd: USB Universal Host Controller Interface driver [ 2.668726] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 2.668751] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.668759] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 2.668910] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.668981] uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000f040 [ 2.669335] hub 2-0:1.0: USB hub found [ 2.669355] hub 2-0:1.0: 2 ports detected [ 2.669508] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 2.669531] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 2.669538] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 2.669675] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 2.669739] uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000f020 [ 2.670099] hub 3-0:1.0: USB hub found [ 2.670118] hub 3-0:1.0: 2 ports detected [ 2.670271] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 2.670295] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 2.670302] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 2.670435] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 2.670502] uhci_hcd 0000:00:1d.2: irq 22, io base 0x0000f000 [ 2.670869] hub 4-0:1.0: USB hub found [ 2.670888] hub 4-0:1.0: 2 ports detected [ 2.671186] usbcore: registered new interface driver libusual [ 2.671332] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 2.673408] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.673437] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.673844] mousedev: PS/2 mouse device common for all mice [ 2.674272] rtc_cmos 00:08: RTC can wake from S4 [ 2.674482] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 [ 2.674529] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs [ 2.674691] device-mapper: uevent: version 1.0.3 [ 2.674903] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 2.675024] EISA: Probing bus 0 at eisa.0 [ 2.675037] EISA: Cannot allocate resource for mainboard [ 2.675050] Cannot allocate resource for EISA slot 1 [ 2.675061] Cannot allocate resource for EISA slot 2 [ 2.675072] Cannot allocate resource for EISA slot 3 [ 2.675083] Cannot allocate resource for EISA slot 4 [ 2.675094] Cannot allocate resource for EISA slot 5 [ 2.675105] Cannot allocate resource for EISA slot 6 [ 2.675116] Cannot allocate resource for EISA slot 7 [ 2.675127] Cannot allocate resource for EISA slot 8 [ 2.675137] EISA: Detected 0 cards. [ 2.675161] cpufreq-nforce2: No nForce2 chipset. [ 2.675401] cpuidle: using governor ladder [ 2.675786] cpuidle: using governor menu [ 2.675797] EFI Variables Facility v0.08 2004-May-17 [ 2.676429] TCP cubic registered [ 2.676751] NET: Registered protocol family 10 [ 2.678031] NET: Registered protocol family 17 [ 2.678052] Registering the dns_resolver key type [ 2.678107] Using IPI No-Shortcut mode [ 2.678515] PM: Hibernation image not present or could not be loaded. [ 2.678543] registered taskstats version 1 [ 2.701145] Magic number: 0:84:234 [ 2.701312] rtc_cmos 00:08: setting system clock to 2012-10-04 15:13:51 UTC (1349363631) [ 2.702280] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 2.702294] EDD information not available. [ 2.702858] Freeing unused kernel memory: 740k freed [ 2.703630] Write protecting the kernel text: 5816k [ 2.703692] Write protecting the kernel read-only data: 2376k [ 2.703706] NX-protecting the kernel data: 4424k [ 2.751226] udevd[84]: starting version 175 [ 2.980162] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 3.001394] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.001474] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.001554] r8169 0000:01:00.0: setting latency timer to 64 [ 3.001654] r8169 0000:01:00.0: irq 43 for MSI/MSI-X [ 3.004220] r8169 0000:01:00.0: eth0: RTL8168c/8111c at 0xf8416000, 00:18:92:03:10:46, XID 1c4000c0 IRQ 43 [ 3.004254] r8169 0000:01:00.0: eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.004347] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.005085] r8169 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 3.005182] r8169 0000:04:00.0: setting latency timer to 64 [ 3.005292] r8169 0000:04:00.0: irq 44 for MSI/MSI-X [ 3.007187] r8169 0000:04:00.0: eth1: RTL8168c/8111c at 0xf8418000, 00:18:92:03:10:47, XID 1c4000c0 IRQ 44 [ 3.007224] r8169 0000:04:00.0: eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.034417] pata_sch 0000:00:1f.1: version 0.2 [ 3.034518] pata_sch 0000:00:1f.1: setting latency timer to 64 [ 3.036698] scsi0 : pata_sch [ 3.039842] scsi1 : pata_sch [ 3.040913] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf060 irq 14 [ 3.040940] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf068 irq 15 [ 3.131850] Initializing USB Mass Storage driver... [ 3.136405] scsi2 : usb-storage 1-1:1.0 [ 3.136642] usbcore: registered new interface driver usb-storage [ 3.136656] USB Mass Storage support registered. [ 3.524465] usb 3-1: new low-speed USB device number 2 using uhci_hcd [ 3.968144] usb 3-2: new full-speed USB device number 3 using uhci_hcd [ 4.137903] scsi 2:0:0:0: Direct-Access TS TS4GUFM-H 1100 PQ: 0 ANSI: 0 CCS [ 4.140067] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 4.140590] sd 2:0:0:0: [sda] 8028160 512-byte logical blocks: (4.11 GB/3.82 GiB) [ 4.141597] sd 2:0:0:0: [sda] Write Protect is off [ 4.141618] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 4.142974] sd 2:0:0:0: [sda] No Caching mode page present [ 4.143000] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.145837] sd 2:0:0:0: [sda] No Caching mode page present [ 4.145858] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.147931] sda: sda1 sda2 < sda5 > [ 4.150972] sd 2:0:0:0: [sda] No Caching mode page present [ 4.151001] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.151023] sd 2:0:0:0: [sda] Attached SCSI disk [ 4.249168] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input2 [ 4.249579] generic-usb 0003:046A:004B.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 046a:004b] on usb-0000:00:1d.1-1/input0 [ 4.287805] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input3 [ 4.289235] generic-usb 0003:046A:004B.0002: input,hidraw1: USB HID v1.11 Mouse [HID 046a:004b] on usb-0000:00:1d.1-1/input1 [ 4.297604] input: EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input4 [ 4.298913] generic-usb 0003:04E7:0050.0003: input,hidraw2: USB HID v1.00 Pointer [EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface] on usb-0000:00:1d.1-2/input0 [ 4.299878] usbcore: registered new interface driver usbhid [ 4.299925] usbhid: USB HID core driver [ 4.352639] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 4.352661] EXT4-fs (sda1): write access will be enabled during recovery [ 8.519257] EXT4-fs (sda1): recovery complete [ 8.564389] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 14.280922] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 14.280944] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 14.310368] udevd[308]: starting version 175 [ 14.353873] Adding 1045500k swap on /dev/sda5. Priority:-1 extents:1 across:1045500k [ 14.428718] lp: driver loaded but no devices found [ 14.521667] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 15.073459] [drm] Initialized drm 1.1.0 20060810 [ 15.097073] psb_gfx: module is from the staging directory, the quality is unknown, you have been warned. [ 15.180630] gma500 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 15.180648] gma500 0000:00:02.0: setting latency timer to 64 [ 15.182117] Stolen memory information [ 15.182127] base in RAM: 0x7f800000 [ 15.182134] size: 7932K, calculated by (GTT RAM base) - (Stolen base), seems wrong [ 15.182143] the correct size should be: 8M(dvmt mode=3) [ 15.234889] Set up 1983 stolen pages starting at 0x7f800000, GTT offset 0K [ 15.235126] [drm] SGX core id = 0x01130000 [ 15.235135] [drm] SGX core rev major = 0x01, minor = 0x02 [ 15.235143] [drm] SGX core rev maintenance = 0x01, designer = 0x00 [ 15.268796] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness [ 15.269888] acpi device:04: registered as cooling_device2 [ 15.270568] acpi device:05: registered as cooling_device3 [ 15.270947] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 15.271238] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 15.271424] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 15.271434] [drm] No driver support for vblank timestamp query. [ 15.374694] type=1400 audit(1349363644.167:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=435 comm="apparmor_parser" [ 15.385518] type=1400 audit(1349363644.179:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=435 comm="apparmor_parser" [ 15.386369] type=1400 audit(1349363644.179:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=435 comm="apparmor_parser" [ 15.677514] r8169 0000:01:00.0: eth0: link down [ 15.694828] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.537490] gma500 0000:00:02.0: allocated 800x480 fb [ 16.558066] fbcon: psbfb (fb0) is primary device [ 16.747122] gma500 0000:00:02.0: BL bug: Reg 00000000 save 00000000 [ 16.775550] Console: switching to colour frame buffer device 100x30 [ 16.781804] fb0: psbfb frame buffer device [ 16.781812] drm: registered panic notifier [ 16.870168] [drm] Initialized gma500 1.0.0 2011-06-06 for 0000:00:02.0 on minor 0 [ 16.871166] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871186] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871207] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 16.871284] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 29.338953] r8169 0000:01:00.0: eth0: link up [ 29.339471] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 31.427223] init: failsafe main process (675) killed by TERM signal [ 31.522411] type=1400 audit(1349363660.316:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=889 comm="apparmor_parser" [ 31.523956] type=1400 audit(1349363660.316:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=889 comm="apparmor_parser" [ 31.524882] type=1400 audit(1349363660.320:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=889 comm="apparmor_parser" [ 31.525940] type=1400 audit(1349363660.320:8): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=891 comm="apparmor_parser" [ 34.526445] postgres (1003): /proc/1003/oom_adj is deprecated, please use /proc/1003/oom_score_adj instead. [ 40.144048] eth0: no IPv6 routers present

  Read the article

• How to keep time on resumed KVM guest with libvirt?

  - by Hristo Hristov

  On my host I am using libvirt and a KVM guest. When the host is shutting down, libvirt suspends the guest. When the host is starting up, libvirt resumes the guest. The problem is, if the guest is suspended and resumed after 24 hours for example, then the guest time is 24 hours in the past. I thought that maybe the problem is with the clocksource, but it is set to "kvm-clock" already. $ cat /sys/devices/system/clocksource/clocksource0/available_clocksource kvm-clock tsc hpet acpi_pm $ cat /sys/devices/system/clocksource/clocksource0/current_clocksource kvm-clock

  Read the article

• Function keys for ASUS n56vm not working

  - by Lars

  i have installed Ubuntu 12.10 (64bits) (3.5.0-18 kernel) on an ASUS N56VM. Most fn+key are working except for: brightness keys (fn+f5/fn+f6) don't work. fn+c - gamma keys fc+v - camera fn+space - toggle speed. I really like, at least, to have the brightness keys working. Can you help? Best Regards $ dmesg | grep -i asus [ 0.000000] DMI: ASUSTeK COMPUTER INC. N56VM/N56VM, BIOS N56VM.206 04/13/2012 [ 0.000000] ACPI: RSDP 00000000cafcc000 00024 (v02 _ASUS_) [ 0.000000] ACPI: XSDT 00000000cafcc078 00074 (v01 _ASUS_ Notebook 01072009 AMI 00010013) [ 0.000000] ACPI: FACP 00000000cafdf858 000F4 (v04 _ASUS_ Notebook 01072009 AMI 00010013) [ 0.000000] ACPI: DSDT 00000000cafcc188 136CA (v02 _ASUS_ Notebook 00000013 INTL 20091112) [ 0.000000] ACPI: APIC 00000000cafdf950 00092 (v03 _ASUS_ Notebook 01072009 AMI 00010013) [ 0.000000] ACPI: FPDT 00000000cafdf9e8 00044 (v01 _ASUS_ Notebook 01072009 AMI 00010013) [ 0.000000] ACPI: ECDT 00000000cafdfa30 000C1 (v01 _ASUS_ Notebook 01072009 AMI. 00000005) [ 0.000000] ACPI: MCFG 00000000cafdfaf8 0003C (v01 _ASUS_ Notebook 01072009 MSFT 00000097) [ 0.000000] ACPI: SLIC 00000000cafdfb38 00176 (v01 _ASUS_ Notebook 01072009 ASUS 00000001) [ 0.000000] ACPI: HPET 00000000cafdfcb0 00038 (v01 _ASUS_ Notebook 01072009 AMI. 00000005) [ 0.000000] ACPI: BGRT 00000000cafe1090 00038 (v00 _ASUS_ Notebook 01072009 ASUS 00010013) [ 9.670500] asus_wmi: ASUS WMI generic driver loaded [ 9.671627] asus_wmi: Initialization: 0x1asus_wmi: BIOS WMI version: 7.9 [ 9.671673] asus_wmi: SFUN value: 0x6a0877<6>[ 9.672086] input: Asus WMI hotkeys as /devices/platform/asus-nb-wmi/input/input4 [ 9.732438] Registered led device: asus::kbd_backlight [ 9.733242] asus_wmi: Backlight controlled by ACPI video driver

  Read the article

• jackd fails to start

  - by wickedchicken

  I'm trying to have a setup where JACK interfaces directly to ALSA and pulseaudio communicates to JACK. This setup worked OK (I had to manually start things a few times) but as I understood the Ubuntu daemon setup and perfected things jackd stopped working completely. I'm running 10.10. If I run something through ALSA I get sound no problem. However, when I run jack with realtime: /usr/bin/jackd -v -R -ch -Z -t2000 -d alsa -P I get the following error: jackd watchdog: timeout - killing jackd Conversely, if I run without realtime: /usr/bin/jackd -v -r -ch -Z -t2000 -d alsa -P I get: ALSA: poll time out, polled for 32032138 usecs DRIVER NT: could not run driver cycle Jack was working just fine before I made these changes; while I don't have an exact copy of my original configuration I recall running the bare minimum of options worked fine. I've seen some articles saying the problem is with ALSA capture. In fact, I tried enabling capture in alsamixer once and everything worked! On reboot that success was not repeated and I haven't been able to get jack working since. That shouldn't matter because specifying -P should obviate any capture issues. Short summary: I can't get jackd to work under any circumstances (unless I specify -d dummy). Sound works with other programs with ALSA, but when I run JACK the daemon opens the card but times out and dies. JACK worked fine before but I can't figure out what changed (or where to even look). I should mention I am running with CPU speed throttling on, but I'm using HPET to mitigate this (and I've run jack with no issue before). Thanks!

  Read the article

• grub problem after grub-repair

  - by alireza

  I had two OS,win 7 and Ubuntu, I was working with win and went out of the room and when came back I saw Grub Rescue!!! I booted live and did grub_repaire and it still says multiple active partitions.operating system not found I feel that it can not find the ubuntu hard drive at all! ! ubuntu@ubuntu:/dev$ sudo fdisk -l Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xde771741 Device Boot Start End Blocks Id System /dev/sda1 * 61 61 0 0 Empty /dev/sda2 2048 30146559 15072256 27 Hidden NTFS WinRE /dev/sda3 * 30146560 30351359 102400 7 HPFS/NTFS/exFAT /dev/sda4 30351360 334483299 152065970 7 HPFS/NTFS/exFAT ubuntu@ubuntu:/dev$ ls autofs dvdrw loop4 ppp ram5 shm tty15 tty29 tty42 tty56 ttyS10 ttyS24 uinput vcsa1 block ecryptfs loop5 psaux ram6 snapshot tty16 tty3 tty43 tty57 ttyS11 ttyS25 urandom vcsa2 bsg fb0 loop6 ptmx ram7 snd tty17 tty30 tty44 tty58 ttyS12 ttyS26 usbmon0 vcsa3 btrfs-control fd loop7 pts ram8 sr0 tty18 tty31 tty45 tty59 ttyS13 ttyS27 usbmon1 vcsa4 bus full loop-control ram0 ram9 stderr tty19 tty32 tty46 tty6 ttyS14 ttyS28 usbmon2 vcsa5 cdrom fuse mapper ram1 random stdin tty2 tty33 tty47 tty60 ttyS15 ttyS29 v4l vcsa6 cdrw fw0 mcelog ram10 rfkill stdout tty20 tty34 tty48 tty61 ttyS16 ttyS3 vcs vcsa7 char hpet mei ram11 rtc tty tty21 tty35 tty49 tty62 ttyS17 ttyS30 vcs1 vga_arbiter console input mem ram12 rtc0 tty0 tty22 tty36 tty5 tty63 ttyS18 ttyS31 vcs2 video0 core kmsg net ram13 sda tty1 tty23 tty37 tty50 tty7 ttyS19 ttyS4 vcs3 zero cpu log network_latency ram14 sda2 tty10 tty24 tty38 tty51 tty8 ttyS2 ttyS5 vcs4 cpu_dma_latency loop0 network_throughput ram15 sda3 tty11 tty25 tty39 tty52 tty9 ttyS20 ttyS6 vcs5 disk loop1 null ram2 sda4 tty12 tty26 tty4 tty53 ttyprintk ttyS21 ttyS7 vcs6 dri loop2 oldmem ram3 sg0 tty13 tty27 tty40 tty54 ttyS0 ttyS22 ttyS8 vcs7 dvd loop3 port ram4 sg1 tty14 tty28 tty41 tty55 ttyS1 ttyS23 ttyS9 vcsa ubuntu@ubuntu:/dev$ someone said { Remove the boot flag from sda1, by typing in a terminal: sudo fdisk /dev/sda1 Then press the 'a' key, and 'Enter'. Then press the '1' key, and 'Enter'. Then press the 'w' key, and 'Enter'. } but after grub-repair I got this log: http://paste.ubuntu.com/1371297/ then I try sudo fdisk /dev/sda1 and But It says unable to open /dev/sda1! which is right as sda1 is not in dev folder (look at the picture!) Can anybody help me? I need to work on my windows for the rest of the semester and don't care of my ubuntu. thank you

  Read the article

• The Internet Key Wave MW833UP is not recognized in Ubuntu

  - by gio900

  I can't use my Onda MW833UP... :( Any advice? Here is something that someone else may understand: ~$: lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 11.10 Release: 11.10 Codename: oneiric ~$: lsusb Bus 001 Device 005: ID 1ee8:0012 ~$: dmesg [ 22.709475] cdc_acm 1-1:1.0: ttyACM0: USB ACM device [ 22.714856] usbcore: registered new interface driver cdc_acm [ 22.714866] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 23.520490] ieee80211 phy0: wl_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement) [ 24.244530] usbcore: registered new interface driver usbserial [ 24.244575] USB Serial support registered for generic [ 24.244673] usbcore: registered new interface driver usbserial_generic [ 24.244681] usbserial: USB Serial Driver core [ 24.265879] USB Serial support registered for GSM modem (1-port) [ 24.285680] usbcore: registered new interface driver option [ 24.285691] option: v0.7.2:USB Driver for GSM modems [ 24.425878] EXT4-fs (sda9): re-mounted. Opts: errors=remount-ro,commit=600 [ 24.736540] EXT4-fs (sda8): re-mounted. Opts: commit=600 [ 35.705796] Easy slow down manager: checking for SABI support. [ 35.706002] Easy slow down manager: SABI is supported (f5189) [ 36.060099] usbcore: deregistering interface driver uvcvideo [ 139.508061] CE: hpet increased min_delta_ns to 20113 nsec [ 6798.378917] usb 1-1: USB disconnect, device number 5 [ 6809.108232] usb 1-1: new high speed USB device number 6 using ehci_hcd [ 6809.242692] scsi5 : usb-storage 1-1:1.0 [ 6810.241257] scsi 5:0:0:0: CD-ROM Onda Datacard CD-ROM 0001 PQ: 0 ANSI: 0 [ 6810.241841] scsi 5:0:0:1: Direct-Access Onda Storage 0001 PQ: 0 ANSI: 0 [ 6810.271410] sr0: scsi3-mmc drive: 0x/0x caddy [ 6810.272099] sr 5:0:0:0: Attached scsi CD-ROM sr0 [ 6810.272852] sr 5:0:0:0: Attached scsi generic sg1 type 5 [ 6810.279954] sd 5:0:0:1: [sdb] Attached SCSI removable disk [ 6810.281210] sd 5:0:0:1: Attached scsi generic sg2 type 0 [ 6810.380591] sr0: CDROM (ioctl) error, command: Xpwrite, Read disk info 51 00 00 00 00 00 00 00 02 00 [ 6810.380617] sr: Sense Key : Hardware Error [current] [ 6810.380625] sr: Add. Sense: No additional sense information [ 6810.613937] sr0: CDROM (ioctl) error, command: Xpwrite, Read disk info 51 00 00 00 00 00 00 00 02 00 [ 6810.613972] sr: Sense Key : Hardware Error [current] [ 6810.613984] sr: Add. Sense: No additional sense information [ 6810.673716] usb 1-1: USB disconnect, device number 6 [ 6815.572142] usb 1-1: new high speed USB device number 7 using ehci_hcd [ 6815.706828] cdc_acm 1-1:1.0: ttyACM0: USB ACM device The last 3 lines are where I inserted the Internet key, then reconnected it. usb-device T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1ee8 ProdID=0012 Rev=00.01 S: Manufacturer=Onda S: Product=MW833UP S: SerialNumber=9230B35D870F9CB7AE684EACC5C12BE5EC33B26E C: #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=01 Driver=cdc_acm I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm Then there is /dev/ttyACM0. When the key is connected to the USB port, everything that will meant...

  Read the article

• Fedora error log file

  - by user111196

  I am running a java application using this wrapper service yajsw. The problem it just stopped without any error in its logs file. So I was wondering will there be any system log file which will indicate the cause of it going down? Partial of the log file. Apr 6 00:12:20 localhost kernel: imklog 3.22.1, log source = /proc/kmsg started. Apr 6 00:12:20 localhost rsyslogd: [origin software="rsyslogd" swVersion="3.22.1" x-pid="2234" x-info="http://www.rsyslog.com"] (re)start Apr 6 00:12:20 localhost kernel: Initializing cgroup subsys cpuset Apr 6 00:12:20 localhost kernel: Initializing cgroup subsys cpu Apr 6 00:12:20 localhost kernel: Linux version 2.6.27.41-170.2.117.fc10.x86_64 ([email protected]) (gcc version 4.3.2 20081105 (Red Hat 4.3.2-7) (GCC) ) #1 SMP Thu Dec 10 10:36:29 EST 2009 Apr 6 00:12:20 localhost kernel: Command line: ro root=UUID=722ebf87-437f-4634-9c68-a82d157fa948 rhgb quiet Apr 6 00:12:20 localhost kernel: KERNEL supported cpus: Apr 6 00:12:20 localhost kernel: Intel GenuineIntel Apr 6 00:12:20 localhost kernel: AMD AuthenticAMD Apr 6 00:12:20 localhost kernel: Centaur CentaurHauls Apr 6 00:12:20 localhost kernel: BIOS-provided physical RAM map: Apr 6 00:12:20 localhost kernel: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) Apr 6 00:12:20 localhost kernel: BIOS-e820: 0000000000100000 - 00000000cfb50000 (usable) Apr 6 00:12:20 localhost kernel: BIOS-e820: 00000000cfb50000 - 00000000cfb66000 (reserved) Apr 6 00:12:20 localhost kernel: BIOS-e820: 00000000cfb66000 - 00000000cfb85c00 (ACPI data) Apr 6 00:12:20 localhost kernel: BIOS-e820: 00000000cfb85c00 - 00000000d0000000 (reserved) Apr 6 00:12:20 localhost kernel: BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) Apr 6 00:12:20 localhost kernel: BIOS-e820: 00000000fe000000 - 0000000100000000 (reserved) Apr 6 00:12:20 localhost kernel: BIOS-e820: 0000000100000000 - 0000000330000000 (usable) Apr 6 00:12:20 localhost kernel: DMI 2.5 present. Apr 6 00:12:20 localhost kernel: last_pfn = 0x330000 max_arch_pfn = 0x3ffffffff Apr 6 00:12:20 localhost kernel: x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 Apr 6 00:12:20 localhost kernel: last_pfn = 0xcfb50 max_arch_pfn = 0x3ffffffff Apr 6 00:12:20 localhost kernel: init_memory_mapping Apr 6 00:12:20 localhost kernel: last_map_addr: cfb50000 end: cfb50000 Apr 6 00:12:20 localhost kernel: init_memory_mapping Apr 6 00:12:20 localhost kernel: last_map_addr: 330000000 end: 330000000 Apr 6 00:12:20 localhost kernel: RAMDISK: 37bfc000 - 37fef6c8 Apr 6 00:12:20 localhost kernel: ACPI: RSDP 000F21B0, 0024 (r2 DELL ) Apr 6 00:12:20 localhost kernel: ACPI: XSDT 000F224C, 0084 (r1 DELL PE_SC3 1 DELL 1) Apr 6 00:12:20 localhost kernel: ACPI: FACP CFB83524, 00F4 (r3 DELL PE_SC3 1 DELL 1) Apr 6 00:12:20 localhost kernel: ACPI: DSDT CFB66000, 4974 (r1 DELL PE_SC3 1 INTL 20050624) Apr 6 00:12:20 localhost kernel: ACPI: FACS CFB85C00, 0040 Apr 6 00:12:20 localhost kernel: ACPI: APIC CFB83078, 00B6 (r1 DELL PE_SC3 1 DELL 1) Apr 6 00:12:20 localhost kernel: ACPI: SPCR CFB83130, 0050 (r1 DELL PE_SC3 1 DELL 1) Apr 6 00:12:20 localhost kernel: ACPI: HPET CFB83184, 0038 (r1 DELL PE_SC3 1 DELL 1) Apr 6 00:12:20 localhost kernel: ACPI: MCFG CFB831C0, 003C (r1 DELL PE_SC3 1 DELL 1) Apr 6 00:12:20 localhost kernel: ACPI: WD__ CFB83200, 0134 (r1 DELL PE_SC3 1 DELL 1) Apr 6 00:12:20 localhost kernel: ACPI: SLIC CFB83338, 0176 (r1 DELL PE_SC3 1 DELL 1) Apr 6 00:12:20 localhost kernel: ACPI: ERST CFB6AAF4, 0210 (r1 DELL PE_SC3 1 DELL 1) Apr 6 00:12:20 localhost kernel: ACPI: HEST CFB6AD04, 027C (r1 DELL PE_SC3 1 DELL 1) Apr 6 00:12:20 localhost kernel: ACPI: BERT CFB6A974, 0030 (r1 DELL PE_SC3 1 DELL 1) Apr 6 00:12:20 localhost kernel: ACPI: EINJ CFB6A9A4, 0150 (r1 DELL PE_SC3 1 DELL 1) Apr 6 00:12:20 localhost kernel: ACPI: TCPA CFB834BC, 0064 (r1 DELL PE_SC3 1 DELL 1) Apr 6 00:12:20 localhost kernel: No NUMA configuration found Apr 6 00:12:20 localhost kernel: Faking a node at 0000000000000000-0000000330000000 Apr 6 00:12:20 localhost kernel: Bootmem setup node 0 0000000000000000-0000000330000000 Apr 6 00:12:20 localhost kernel: NODE_DATA [0000000000015000 - 0000000000029fff] Apr 6 00:12:20 localhost kernel: bootmap [000000000002a000 - 000000000008ffff] pages 66 Apr 6 00:12:20 localhost kernel: (7 early reservations) ==> bootmem [0000000000 - 0330000000] Apr 6 00:12:20 localhost kernel: #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] Apr 6 00:12:20 localhost kernel: #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] Apr 6 00:12:20 localhost kernel: #2 [0000200000 - 0000a310cc] TEXT DATA BSS ==> [0000200000 - 0000a310cc] Apr 6 00:12:20 localhost kernel: #3 [0037bfc000 - 0037fef6c8] RAMDISK ==> [0037bfc000 - 0037fef6c8] Apr 6 00:12:20 localhost kernel: #4 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000] Apr 6 00:12:20 localhost kernel: #5 [0000008000 - 000000c000] PGTABLE ==> [0000008000 - 000000c000] Apr 6 00:12:20 localhost kernel: #6 [000000c000 - 0000015000] PGTABLE ==> [000000c000 - 0000015000] Apr 6 00:12:20 localhost kernel: found SMP MP-table at [ffff8800000fe710] 000fe710 Apr 6 00:12:20 localhost kernel: Zone PFN ranges: Apr 6 00:12:20 localhost kernel: DMA 0x00000000 -> 0x00001000 Apr 6 00:12:20 localhost kernel: DMA32 0x00001000 -> 0x00100000 Apr 6 00:12:20 localhost kernel: Normal 0x00100000 -> 0x00330000 Apr 6 00:12:20 localhost kernel: Movable zone start PFN for each node Apr 6 00:12:20 localhost kernel: early_node_map[3] active PFN ranges Apr 6 00:12:20 localhost kernel: 0: 0x00000000 -> 0x000000a0 Apr 6 00:12:20 localhost kernel: 0: 0x00000100 -> 0x000cfb50 Apr 6 00:12:20 localhost kernel: 0: 0x00100000 -> 0x00330000 Apr 6 00:12:20 localhost kernel: ACPI: PM-Timer IO Port: 0x808 Apr 6 00:12:20 localhost kernel: ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Apr 6 00:12:20 localhost kernel: ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled) Apr 6 00:12:20 localhost kernel: ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) Apr 6 00:12:20 localhost kernel: ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled) Apr 6 00:12:20 localhost kernel: ACPI: LAPIC (acpi_id[0x05] lapic_id[0x01] enabled) Apr 6 00:12:20 localhost kernel: ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled) Apr 6 00:12:20 localhost kernel: ACPI: LAPIC (acpi_id[0x07] lapic_id[0x03] enabled) Apr 6 00:12:20 localhost kernel: ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled) Apr 6 00:12:20 localhost kernel: ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1]) Apr 6 00:12:20 localhost kernel: ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) Apr 6 00:12:20 localhost kernel: IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23 Apr 6 00:12:20 localhost kernel: ACPI: IOAPIC (id[0x09] address[0xfec81000] gsi_base[64]) Apr 6 00:12:20 localhost kernel: IOAPIC[1]: apic_id 9, version 0, address 0xfec81000, GSI 64-87 Apr 6 00:12:20 localhost kernel: ACPI: IOAPIC (id[0x0a] address[0xfec84000] gsi_base[160]) Apr 6 00:12:20 localhost kernel: IOAPIC[2]: apic_id 10, version 0, address 0xfec84000, GSI 160-183 Apr 6 00:12:20 localhost kernel: ACPI: IOAPIC (id[0x0b] address[0xfec84800] gsi_base[224]) Apr 6 00:12:20 localhost kernel: IOAPIC[3]: apic_id 11, version 0, address 0xfec84800, GSI 224-247 Apr 6 00:12:20 localhost kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Apr 6 00:12:20 localhost kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) Apr 6 00:12:20 localhost kernel: Setting APIC routing to flat Apr 6 00:12:20 localhost kernel: ACPI: HPET id: 0x8086a201 base: 0xfed00000 Apr 6 00:12:20 localhost kernel: Using ACPI (MADT) for SMP configuration information Apr 6 00:12:20 localhost kernel: SMP: Allowing 8 CPUs, 0 hotplug CPUs Apr 6 00:12:20 localhost kernel: PM: Registered nosave memory: 00000000000a0000 - 0000000000100000 Apr 6 00:12:20 localhost kernel: PM: Registered nosave memory: 00000000cfb50000 - 00000000cfb66000 Apr 6 00:12:20 localhost kernel: PM: Registered nosave memory: 00000000cfb66000 - 00000000cfb85000 Apr 6 00:12:20 localhost kernel: PM: Registered nosave memory: 00000000cfb85000 - 00000000cfb86000 Apr 6 00:12:20 localhost kernel: PM: Registered nosave memory: 00000000cfb86000 - 00000000d0000000 Apr 6 00:12:20 localhost kernel: PM: Registered nosave memory: 00000000d0000000 - 00000000e0000000 Apr 6 00:12:20 localhost kernel: PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000 Apr 6 00:12:20 localhost kernel: PM: Registered nosave memory: 00000000f0000000 - 00000000fe000000 Apr 6 00:12:20 localhost kernel: PM: Registered nosave memory: 00000000fe000000 - 0000000100000000 Apr 6 00:12:20 localhost kernel: Allocating PCI resources starting at d1000000 (gap: d0000000:10000000) Apr 6 00:12:20 localhost kernel: PERCPU: Allocating 65184 bytes of per cpu data Apr 6 00:12:20 localhost kernel: Built 1 zonelists in Zone order, mobility grouping on. Total pages: 3096524 Apr 6 00:12:20 localhost kernel: Policy zone: Normal Apr 6 00:12:20 localhost kernel: Kernel command line: ro root=UUID=722ebf87-437f-4634-9c68-a82d157fa948 rhgb quiet Apr 6 00:12:20 localhost kernel: Initializing CPU#0 Apr 6 00:12:20 localhost kernel: PID hash table entries: 4096 (order: 12, 32768 bytes) Apr 6 00:12:20 localhost kernel: Extended CMOS year: 2000 Apr 6 00:12:20 localhost kernel: TSC: PIT calibration confirmed by PMTIMER. Apr 6 00:12:20 localhost kernel: TSC: using PMTIMER calibration value Apr 6 00:12:20 localhost kernel: Detected 1994.992 MHz processor. Apr 6 00:12:20 localhost kernel: Console: colour VGA+ 80x25 Apr 6 00:12:20 localhost kernel: console [tty0] enabled Apr 6 00:12:20 localhost kernel: Checking aperture... Apr 6 00:12:20 localhost kernel: No AGP bridge found Apr 6 00:12:20 localhost kernel: PCI-DMA: Using software bounce buffering for IO (SWIOTLB) Apr 6 00:12:20 localhost kernel: Placing software IO TLB between 0x20000000 - 0x24000000 Apr 6 00:12:20 localhost kernel: Memory: 12324244k/13369344k available (3311k kernel code, 253484k reserved, 1844k data, 1296k init) Apr 6 00:12:20 localhost kernel: SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 Apr 6 00:12:20 localhost kernel: Calibrating delay loop (skipped), value calculated using timer frequency.. 3989.98 BogoMIPS (lpj=1994992) Apr 6 00:12:20 localhost kernel: Security Framework initialized Apr 6 00:12:20 localhost kernel: SELinux: Initializing. Apr 6 00:12:20 localhost kernel: Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes) Apr 6 00:12:20 localhost kernel: Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes) Apr 6 00:12:20 localhost kernel: Mount-cache hash table entries: 256 Apr 6 00:12:20 localhost kernel: Initializing cgroup subsys ns Apr 6 00:12:20 localhost kernel: Initializing cgroup subsys cpuacct Apr 6 00:12:20 localhost kernel: Initializing cgroup subsys devices Apr 6 00:12:20 localhost kernel: CPU: L1 I cache: 32K, L1 D cache: 32K Apr 6 00:12:20 localhost kernel: CPU: L2 cache: 4096K Apr 6 00:12:20 localhost kernel: CPU 0/0 -> Node 0 Apr 6 00:12:20 localhost kernel: CPU: Physical Processor ID: 0 Apr 6 00:12:20 localhost kernel: CPU: Processor Core ID: 0 Apr 6 00:12:20 localhost kernel: CPU0: Thermal monitoring enabled (TM1) Apr 6 00:12:20 localhost kernel: using mwait in idle threads. Apr 6 00:12:20 localhost kernel: ACPI: Core revision 20080609 Apr 6 00:12:20 localhost kernel: ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 Apr 6 00:12:20 localhost kernel: CPU0: Intel(R) Xeon(R) CPU E5335 @ 2.00GHz stepping 07 Apr 6 00:12:20 localhost kernel: Using local APIC timer interrupts. Apr 6 00:12:20 localhost kernel: Detected 20.781 MHz APIC timer. Apr 6 00:12:20 localhost kernel: Booting processor 1/4 ip 6000 Apr 6 00:12:20 localhost kernel: Initializing CPU#1 Apr 6 00:12:20 localhost kernel: Calibrating delay using timer specific routine.. 3990.05 BogoMIPS (lpj=1995026) Apr 6 00:12:20 localhost kernel: CPU: L1 I cache: 32K, L1 D cache: 32K Apr 6 00:12:20 localhost kernel: CPU: L2 cache: 4096K Apr 6 00:12:20 localhost kernel: CPU 1/4 -> Node 0 Apr 6 00:12:20 localhost kernel: CPU: Physical Processor ID: 1 Apr 6 00:12:20 localhost kernel: CPU: Processor Core ID: 0 Apr 6 00:12:20 localhost kernel: CPU1: Thermal monitoring enabled (TM2) Apr 6 00:12:20 localhost kernel: x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 Apr 6 00:12:20 localhost kernel: CPU1: Intel(R) Xeon(R) CPU E5335 @ 2.00GHz stepping 07 Apr 6 00:12:20 localhost kernel: checking TSC synchronization [CPU#0 -> CPU#1]: passed. Apr 6 00:12:20 localhost kernel: Booting processor 2/2 ip 6000 Apr 6 00:12:20 localhost kernel: Initializing CPU#2 Apr 6 00:12:20 localhost kernel: Calibrating delay using timer specific routine.. 3990.05 BogoMIPS (lpj=1995029)

  Read the article

• Weird mouse behaviour. Debian wheezy

  - by DevNoob

  When I move my mouse slowly over the desktop the pointer jumps often a few pixels (one or two) in the opposite direction of which I move my mouse. Horribly when trying to set the cursor around some semicolons in eclipse. I guess this is the result of a wrong set resolution of it. I suppose this is because the mouse was set initially really fast and even if I do xset 1/2 3, the mouse is just to fast and unprecise for me. It aready tried to configure the xorg.conf like this: Section "InputDevice" Identifier "Configured Mouse" Driver "mouse" Option "Device" "/dev/mouse" Option "Protocol" "Auto" Option "Name" "Logitech G3" Option "Resolution" "2000" EndSection But with no effect. Maybe because there is no /dev/mouse. This ist the content of dev. Maybe you can tell me which one is the mouse. autofs block bsg btrfs-control bus cdrom cdrw char console core cpu cpu_dma_latency disk dvd dvdrw fd fd0 full fuse fw0 hidraw0 hidraw1 hpet input kmsg log loop0 loop1 loop2 loop3 loop4 loop5 loop6 loop7 loop-control MAKEDEV mapper mcelog mem net network_latency network_throughput null nvidia0 nvidiactl oldmem port ppp printer psaux ptmx pts random rfkill root rtc rtc0 sda sda1 sda2 sda3 sda5 sda6 sda7 sda8 sdb sdb1 sg0 sg1 sg2 shm snapshot snd sndstat sr0 stderr stdin stdout tty tty0 tty1 tty10 tty11 tty12 tty13 tty14 tty15 tty16 tty17 tty18 tty19 tty2 tty20 tty21 tty22 tty23 tty24 tty25 tty26 tty27 tty28 tty29 tty3 tty30 tty31 tty32 tty33 tty34 tty35 tty36 tty37 tty38 tty39 tty4 tty40 tty41 tty42 tty43 tty44 tty45 tty46 tty47 tty48 tty49 tty5 tty50 tty51 tty52 tty53 tty54 tty55 tty56 tty57 tty58 tty59 tty6 tty60 tty61 tty62 tty63 tty7 tty8 tty9 ttyS0 ttyS1 ttyS2 ttyS3 uinput urandom usb vcs vcs1 vcs2 vcs3 vcs4 vcs5 vcs6 vcs7 vcsa vcsa1 vcsa2 vcsa3 vcsa4 vcsa5 vcsa6 vcsa7 vga_arbiter vmci vmmon vmnet0 vmnet1 vmnet8 vsock watchdog xconsole zero So my question is: How do I setup my mouse correctly in Debian wheezy?

  Read the article

• clocksource tsc unstable

  - by amorfis

  Ok, now I have real server fault ;) After some time from booting (about one minute) my server hangs. All I can do is hard reset. Then after restart in /var/log/kern.log I can find: Jul 29 22:38:57 leonidas kernel: [ 90.729598] longhaul: Failed to set requested frequency! Jul 29 22:38:57 leonidas kernel: [ 90.731252] longhaul: Enabling "Ignore Revision ID" option. Jul 29 22:38:57 leonidas kernel: [ 91.201461] longhaul: Failed to set requested frequency! Jul 29 22:38:57 leonidas kernel: [ 91.201482] longhaul: Disabling ACPI C3 support. Jul 29 22:38:57 leonidas kernel: [ 91.204230] longhaul: Disabling "Ignore Revision ID" option. Jul 29 22:38:58 leonidas kernel: [ 91.416133] longhaul: Failed to set requested frequency! Jul 29 22:38:58 leonidas kernel: [ 91.416152] longhaul: Enabling "Ignore Revision ID" option. Jul 29 22:38:58 leonidas kernel: [ 91.960048] Clocksource tsc unstable (delta = -105611479 ns) I found some resources on the net, and it said to change clocksource, or disable ACPI. I tried disabling ACPI but it didn't help (but I noticed there was longer time before hanging). I can't change clock to hpet, because my system doesn't have such one. Output of cat /sys/devices/system/clocksource/clocksource0/available_clocksource: acpi_pm jiffies tsc My system is ubuntu server on VIA Epia hardware.

  Read the article

• How to check if a cdrom is in the tray remotely (via ssh)?

  - by adempewolff

  I have a server running Ubuntu 10.04 (it's on the other side of the world and I haven't built up the wherewithal to upgrade it remotely yet) and I have been told that there is a CD in one of it's two CD drives. I want to rip an image of the cd and then download it to my local computer (I don't need help with either of these steps). However, I cannot seem to confirm whether or not there actually is a CD in the drive as I was told. It did not automatically mount anywhere (which I'm thinking might just be a result of it being a headless server not running X, nautilus, or any of the other nice user friendly things). There are two CD drives connected via SCSI: austin@austinvpn:/proc/scsi$ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: ATA Model: WDC WD400EB-75CP Rev: 06.0 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: Lite-On Model: LTN486S 48x Max Rev: YDS6 Type: CD-ROM ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 01 Lun: 00 Vendor: SAMSUNG Model: CD-R/RW SW-248F Rev: R602 Type: CD-ROM ANSI SCSI revision: 05 However when I try mounting either of these devices (and every other device that could possibly be the cd-drive), it says no medium found: austin@austinvpn:/proc/scsi$ sudo mount -t iso9660 /dev/scd1 /cdrom mount: no medium found on /dev/sr1 austin@austinvpn:/proc/scsi$ sudo mount -t iso9660 /dev/scd0 /cdrom mount: no medium found on /dev/sr0 austin@austinvpn:/proc/scsi$ sudo mount -t iso9660 /dev/cdrom /cdrom mount: no medium found on /dev/sr1 austin@austinvpn:/proc/scsi$ sudo mount -t iso9660 /dev/cdrom1 /cdrom mount: no medium found on /dev/sr0 austin@austinvpn:/proc/scsi$ sudo mount -t iso9660 /dev/cdrw /cdrom mount: no medium found on /dev/sr1 Here are the contents of my /dev folder: austin@austinvpn:/proc/scsi$ ls /dev agpgart loop6 ram6 tty10 tty38 tty8 austinvpn loop7 ram7 tty11 tty39 tty9 block lp0 ram8 tty12 tty4 ttyS0 bsg mapper ram9 tty13 tty40 ttyS1 btrfs-control mcelog random tty14 tty41 ttyS2 bus mem rfkill tty15 tty42 ttyS3 cdrom net root tty16 tty43 urandom cdrom1 network_latency rtc tty17 tty44 usbmon0 cdrw network_throughput rtc0 tty18 tty45 usbmon1 char null scd0 tty19 tty46 usbmon2 console oldmem scd1 tty2 tty47 usbmon3 core parport0 sda tty20 tty48 usbmon4 cpu_dma_latency pktcdvd sda1 tty21 tty49 vcs disk port sda2 tty22 tty5 vcs1 dri ppp sda5 tty23 tty50 vcs2 ecryptfs psaux sg0 tty24 tty51 vcs3 fb0 ptmx sg1 tty25 tty52 vcs4 fd pts sg2 tty26 tty53 vcs5 full ram0 shm tty27 tty54 vcs6 fuse ram1 snapshot tty28 tty55 vcs7 hpet ram10 snd tty29 tty56 vcsa input ram11 sndstat tty3 tty57 vcsa1 kmsg ram12 sr0 tty30 tty58 vcsa2 log ram13 sr1 tty31 tty59 vcsa3 loop0 ram14 stderr tty32 tty6 vcsa4 loop1 ram15 stdin tty33 tty60 vcsa5 loop2 ram2 stdout tty34 tty61 vcsa6 loop3 ram3 tty tty35 tty62 vcsa7 loop4 ram4 tty0 tty36 tty63 vga_arbiter loop5 ram5 tty1 tty37 tty7 zero And here is my fstab file: austin@austinvpn:/proc/scsi$ cat /etc/fstab # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 /dev/mapper/austinvpn-root / ext4 errors=remount-ro 0 1 # /boot was on /dev/sda1 during installation UUID=ed5520ae-c690-4ce6-881e-3598f299be06 /boot ext2 defaults 0 2 /dev/mapper/austinvpn-swap_1 none swap sw 0 0 Am I missing something/doing something wrong, or is there just no CD in the drive or is the drive possibly broken? Is there any nice command to list devices with mountable media? Thanks in advance for any help!

  Read the article

• How to remove iso 9660 from USB?

  - by a_m0d

  I have somehow managed to write an iso 9660 image onto my USB drive, which makes all my computer think that the device is actually a CD. I have tried various methods of removing this partition, but nothing seems to work. I have tried fdisk, which says $ fdisk -l /dev/sdb Cannot open /dev/sdb parted crashes when I try to use it on this device. I have even tried $ dd if=/dev/zero of=/dev/sdb but it just hangs with no output (either on screen or on disk). However, when I plug the USB in, it does mount, and I can view (but not edit) the files on it. edit: now the result is $ dd if=/dev/zero of=/dev/sdb dd: opening `/dev/sdb': Read-only file system I have also tried re-formatting it on Windows, but it gets to the end of the format process and then says "Couldn't format the drive". How can I remove this partition and get my whole USB drive back to normal again? EDIT 1: Trying a simple mkfs doesn't work: $ sudo mkfs -t vfat /dev/sdb mkfs.vfat 3.0.0 (28 Sep 2008) mkfs.vfat: Will not try to make filesystem on full-disk device '/dev/sdb' (use -I if wanted) I can't do mkfs on /dev/sdb1 because there is no such partition, as shown:$ ls /dev | grep sdb sdb EDIT 2: This is the information posted by dmesg when I plug the device in:$ dmesg . . (snip) . usb 2-1: New USB device found, idVendor=058f, idProduct=6387 usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1: Product: Mass Storage usb 2-1: Manufacturer: Generic usb 2-1: SerialNumber: G0905000000000010885 usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 6:0:0:0: Direct-Access FLASH Drive AU_USB20 8.07 PQ: 0 ANSI: 2 sd 6:0:0:0: [sdb] 4069376 512-byte hardware sectors (2084 MB) sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sd 6:0:0:0: [sdb] 4069376 512-byte hardware sectors (2084 MB) sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sdb: unknown partition table sd 6:0:0:0: [sdb] Attached SCSI removable disk sd 6:0:0:0: Attached scsi generic sg2 type 0 ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A SELinux: initialized (dev sdb, type iso9660), uses genfs_contexts CE: hpet increasing min_delta_ns to 15000 nsec This shows that the device is formatted as ISO 9660 and that it is /dev/sdb. EDIT 3: This is the message that I find at the bottom of dmesg after running cfdisk and writing a new partition table to the disk:SELinux: initialized (dev sdb, type iso9660), uses genfs_contexts sd 17:0:0:0: [sdb] Device not ready: Sense Key : Not Ready [current] sd 17:0:0:0: [sdb] Device not ready: < ASC=0xff ASCQ=0xffASC=0xff < ASCQ=0xff end_request: I/O error, dev sdb, sector 0 Buffer I/O error on device sdb, logical block 0 lost page write due to I/O error on sdb

  Read the article

• 64-bit linux kernel only seeing 3 of 4GB after upgrade...

  - by Blaine

  Hey everyone. I am running Ubuntu 9.04 64-bit on my macbook. I had 2GB of ram before, and everything ran great. I just upgraded to 2x2GB (4GB), but my system only sees 3GB of it. OS X, which I am dual booting, sees all 4GB. Also, my video performance is incredibly lacking. Before the upgrade my compiz benchmark was full at 80fps, and now it is at 22fps with very choppy window dragging. Has anyone ever heard of this on a 64-bit kernel? I just don't quite understand what could be the issue. 10$ uname -a Linux macbook 2.6.28-15-generic #49-Ubuntu SMP Tue Aug 18 19:25:34 UTC 2009 x86_64 GNU/Linux $ free -m total used free shared buffers cached Mem: 2953 1031 1921 0 114 427 -/+ buffers/cache: 489 2463 Swap: 7812 0 7812 9$ lsmod Module Size Used by i915 77960 2 drm 123232 3 i915 binfmt_misc 18572 1 ppdev 16904 0 btusb 21784 2 bridge 63776 0 stp 11140 1 bridge bnep 22912 2 vboxnetadp 109356 0 vboxnetflt 116972 0 vboxdrv 1721612 1 vboxnetflt uvcvideo 69640 0 compat_ioctl32 18304 1 uvcvideo videodev 45184 2 uvcvideo,compat_ioctl32 v4l1_compat 23940 2 uvcvideo,videodev lp 19588 0 parport 49584 2 ppdev,lp snd_hda_intel 557492 3 snd_pcm_oss 52352 0 snd_mixer_oss 24960 1 snd_pcm_oss snd_pcm 99464 2 snd_hda_intel,snd_pcm_oss arc4 10240 2 snd_seq_dummy 11524 0 ecb 11392 2 snd_seq_oss 41984 0 snd_seq_midi 15744 0 snd_rawmidi 33920 1 snd_seq_midi snd_seq_midi_event 16512 2 snd_seq_oss,snd_seq_midi snd_seq 66272 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event ath9k 310584 0 snd_timer 34064 2 snd_pcm,snd_seq snd_seq_device 16276 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq mac80211 251528 1 ath9k iTCO_wdt 21712 0 iTCO_vendor_support 12420 1 iTCO_wdt joydev 20992 0 video 29204 0 snd 78920 15 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device applesmc 37700 0 output 11648 1 video soundcore 16800 1 snd pcspkr 11136 0 cfg80211 43680 1 mac80211 appletouch 19972 0 isight_firmware 11520 0 input_polldev 12688 1 applesmc intel_agp 39408 1 snd_page_alloc 18704 2 snd_hda_intel,snd_pcm led_class 13064 2 ath9k,applesmc hid_apple 15872 0 usbhid 47040 0 ohci1394 42164 0 ieee1394 108288 1 ohci1394 sky2 63364 0 fbcon 49792 0 tileblit 11264 1 fbcon font 17024 1 fbcon bitblit 14464 1 fbcon softcursor 10368 1 bitblit Some information from dmesg: [ 795.820163] ACPI: EC: GPE storm detected, transactions will use polling mode [ 1762.709516] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 1763.078130] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 2362.760889] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 2416.352084] ACPI: EC: missing confirmations, switch off interrupt mode. [ 3718.721095] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 3719.108914] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 4318.773266] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 9513.813066] CE: hpet increasing min_delta_ns to 15000 nsec [ 9693.815684] npviewer.bin[6736]

  Read the article

• Slow boot on Ubuntu 12.04

  - by Hailwood

  My Ubuntu is booting really slow (Windows is booting faster...). I am using Ubuntu a Dell Inspiron 1545 Pentium(R) Dual-Core CPU T4300 @ 2.10GHz, 4GB Ram, 500GB HDD running Ubuntu 12.04 with gnome-shell 3.4.1. After running dmesg the culprit seems to be this section, in particular the last three lines: [26.557659] ADDRCONF(NETDEV_UP): eth0: link is not ready [26.565414] ADDRCONF(NETDEV_UP): eth0: link is not ready [27.355355] Console: switching to colour frame buffer device 170x48 [27.362346] fb0: radeondrmfb frame buffer device [27.362347] drm: registered panic notifier [27.362357] [drm] Initialized radeon 2.12.0 20080528 for 0000:01:00.0 on minor 0 [27.617435] init: udev-fallback-graphics main process (1049) terminated with status 1 [30.064481] init: plymouth-stop pre-start process (1500) terminated with status 1 [51.708241] CE: hpet increased min_delta_ns to 20113 nsec [59.448029] eth2: no IPv6 routers present But I have no idea how to start debugging this. sudo lshw -C video $ sudo lshw -C video *-display description: VGA compatible controller product: RV710 [Mobility Radeon HD 4300 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=fglrx_pci latency=0 resources: irq:48 memory:e0000000-efffffff ioport:de00(size=256) memory:f6df0000-f6dfffff memory:f6d00000-f6d1ffff After loading the propriety driver my new dmesg log is below (starting from the first major time gap): [2.983741] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [25.094327] ADDRCONF(NETDEV_UP): eth0: link is not ready [25.119737] udevd[520]: starting version 175 [25.167086] lp: driver loaded but no devices found [25.215341] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [25.215345] Disabling lock debugging due to kernel taint [25.231924] wmi: Mapper loaded [25.318414] lib80211: common routines for IEEE802.11 drivers [25.318418] lib80211_crypt: registered algorithm 'NULL' [25.331631] [fglrx] Maximum main memory to use for locked dma buffers: 3789 MBytes. [25.332095] [fglrx] vendor: 1002 device: 9552 count: 1 [25.334206] [fglrx] ioport: bar 1, base 0xde00, size: 0x100 [25.334229] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [25.334235] pci 0000:01:00.0: setting latency timer to 64 [25.337109] [fglrx] Kernel PAT support is enabled [25.337140] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [25.342803] Adding 4189180k swap on /dev/sda7. Priority:-1 extents:1 across:4189180k [25.364031] type=1400 audit(1338241723.027:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=606 comm="apparmor_parser" [25.364491] type=1400 audit(1338241723.031:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=606 comm="apparmor_parser" [25.364760] type=1400 audit(1338241723.031:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=606 comm="apparmor_parser" [25.394328] wl 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [25.394343] wl 0000:0c:00.0: setting latency timer to 64 [25.415531] acpi device:36: registered as cooling_device2 [25.416688] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:34/LNXVIDEO:00/input/input6 [25.416795] ACPI: Video Device [VID] (multi-head: yes rom: no post: no) [25.416865] [Firmware Bug]: Duplicate ACPI video bus devices for the same VGA controller, please try module parameter "video.allow_duplicates=1"if the current driver doesn't work. [25.425133] lib80211_crypt: registered algorithm 'TKIP' [25.448058] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [25.448321] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [25.448353] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [25.738867] eth1: Broadcom BCM4315 802.11 Hybrid Wireless Controller 5.100.82.38 [25.761213] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [25.761406] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [25.783432] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [25.908318] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro [25.928155] input: Dell WMI hotkeys as /devices/virtual/input/input9 [25.960561] udevd[543]: renamed network interface eth1 to eth2 [26.285688] init: failsafe main process (835) killed by TERM signal [26.396426] input: PS/2 Mouse as /devices/platform/i8042/serio2/input/input10 [26.423108] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio2/input/input11 [26.511297] Bluetooth: Core ver 2.16 [26.511383] NET: Registered protocol family 31 [26.511385] Bluetooth: HCI device and connection manager initialized [26.511388] Bluetooth: HCI socket layer initialized [26.511391] Bluetooth: L2CAP socket layer initialized [26.512079] Bluetooth: SCO socket layer initialized [26.530164] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [26.530168] Bluetooth: BNEP filters: protocol multicast [26.553893] type=1400 audit(1338241724.219:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=928 comm="apparmor_parser" [26.554860] Bluetooth: RFCOMM TTY layer initialized [26.554866] Bluetooth: RFCOMM socket layer initialized [26.554868] Bluetooth: RFCOMM ver 1.11 [26.557910] type=1400 audit(1338241724.223:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=927 comm="apparmor_parser" [26.559166] type=1400 audit(1338241724.223:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=928 comm="apparmor_parser" [26.559574] type=1400 audit(1338241724.223:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=928 comm="apparmor_parser" [26.575519] type=1400 audit(1338241724.239:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=931 comm="apparmor_parser" [26.581100] type=1400 audit(1338241724.247:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=931 comm="apparmor_parser" [26.582794] type=1400 audit(1338241724.247:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=929 comm="apparmor_parser" [26.605672] ppdev: user-space parallel port driver [27.592475] sky2 0000:09:00.0: eth0: enabling interface [27.604329] ADDRCONF(NETDEV_UP): eth0: link is not ready [27.606962] ADDRCONF(NETDEV_UP): eth0: link is not ready [27.852509] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [27.852513] vesafb: scrolling: redraw [27.852515] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [27.852523] mtrr: type mismatch for e0000000,400000 old: write-back new: write-combining [27.852527] mtrr: type mismatch for e0000000,200000 old: write-back new: write-combining [27.852531] mtrr: type mismatch for e0000000,100000 old: write-back new: write-combining [27.852534] mtrr: type mismatch for e0000000,80000 old: write-back new: write-combining [27.852538] mtrr: type mismatch for e0000000,40000 old: write-back new: write-combining [27.852541] mtrr: type mismatch for e0000000,20000 old: write-back new: write-combining [27.852544] mtrr: type mismatch for e0000000,10000 old: write-back new: write-combining [27.852548] mtrr: type mismatch for e0000000,8000 old: write-back new: write-combining [27.852551] mtrr: type mismatch for e0000000,4000 old: write-back new: write-combining [27.852554] mtrr: type mismatch for e0000000,2000 old: write-back new: write-combining [27.852558] mtrr: type mismatch for e0000000,1000 old: write-back new: write-combining [27.853154] vesafb: framebuffer at 0xe0000000, mapped to 0xffffc90005580000, using 3072k, total 3072k [27.853405] Console: switching to colour frame buffer device 128x48 [27.853426] fb0: VESA VGA frame buffer device [28.539800] fglrx_pci 0000:01:00.0: irq 48 for MSI/MSI-X [28.540552] [fglrx] Firegl kernel thread PID: 1168 [28.540679] [fglrx] Firegl kernel thread PID: 1169 [28.540789] [fglrx] Firegl kernel thread PID: 1170 [28.540932] [fglrx] IRQ 48 Enabled [29.845620] [fglrx] Gart USWC size:1236 M. [29.845624] [fglrx] Gart cacheable size:489 M. [29.845629] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [29.845632] [fglrx] Reserved FB block: Unshared offset:fc21000, size:3df000 [29.845635] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [59.700023] eth2: no IPv6 routers present

  Read the article

• CD/DVD drive not mounted when inserted with Disc of any kind

  - by Cisco Sán

  I just noticed that if a insert a CD or a DVD of any kind, the Drive will start spinning but it will not show the mounted disc. Before it used to ask me what to do with the media inserted. Now it doesn't even do that. I ran in the terminal this code: eject -n and it displays this: " eject: device is `/dev/sr0'" what can I do to get the functionality back on my drive. also ran this command: sudo mount -o ro,unhide,uid=1000 /dev/cdrom /mnt/cdrom but in return i get this: " mount: mount point /mnt/cdrom does not exist" Running Ubuntu 11.10 HERE IS THE HISTORY UNTIL NOW thanks Waltinator: I ran the 'dmesg' but don't know what I'm looking for. Im a newbie on this. The same thing with the 'ls -rlt /var/log' command. Should I create the directory for the mount? at this point really don't know what to do. – Cisco Sán 7 hours ago Here are 3 lines from my dmesg after I successfully inserted a CD: [ 4804.416018] wlan0: no IPv6 routers present [ 8214.125450] ISdit ISO 9660 Extensions: Microsoft Joliet Level 3 [ 8214.136556] ISO 9660 Extensions: RRIP_1991A The first line is a previous event, my wireless going online. The next 2 lines are a good result. The number in square brackets is "seconds since boot", the rest of the line is usually helpful. And no, you should NOT create the mount point. Let's try to get the automatic mounting to work. – waltinator 7 hours ago ok this are my last 3 lines on the 'dmesg' [ 18.130819] init: plymouth-stop pre-start process (1396) terminated with status 1 [ 28.780011] wlan0: no IPv6 routers present [ 505.632119] CE: hpet increased min_delta_ns to 20113 nsec – Cisco Sán 6 hours ago It looks like your CD/DVD drive is not connected to the data bus, and not causing an interrupt when you insert a platter. – waltinator 6 hours ago Try dmesg | grep -A8 CD-ROM which should show you what the system thought was available when it came up. – waltinator 6 hours ago here is my printout [0.774351] scsi 0:0:0:0: CD-ROM HL-DT-ST DVD+-RW GSA-T40N A100 PQ: 0 ANSI: 5 [0.778117] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [0.778122] cdrom: Uniform CD-ROM driver Revision: 3.20 [0.778282] sr 0:0:0:0: Attached scsi CD-ROM sr0 [0.778340] sr 0:0:0:0: Attached scsi generic sg0 type 5 [0.780416] Freeing unused kernel memory: 984k freed [0.780732] Write protecting the kernel read-only data: 10240k [0.780986] Freeing unused kernel memory: 20k freed [0.786331] Freeing unused kernel memory: 1400k freed [0.804912] udevd[90]: starting version 173 [0.874178] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [0.874208] r8169 0000:02:00.0: PCI INT A - GSI 16 (level, low) - IRQ 16 OK, your system sees the drive. Can you open and close the tray with eject and eject -t? Run udevadm monitor while you insert a CD (type ^C when done) and see if you get "change" and "add" messages. – waltinator 6 hours ago ok, "eject" works perfectly "eject -t" does nothing. this is the message for "udevadm monitor": KERNEL[13771.009267] change /devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0/block/sr0 (block) UDEV [13773.878887] change /devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0 /block/sr0 (block) – Cisco Sán 6 hours ago sudo hwinfo --cdrom (the hwinfo package is installable through Software Center) describes my CD-ROM, try it. – waltinator 4 hours ago My read out from the "sudo hwinfo --cdrom" are the following: hal.1: read hal dataprocess 2753: arguments to dbus_move_error() were incorrect, assertion "(dest) == NULL || !dbus_error_is_set ((dest))" failed in file ../../dbus/dbus-errors.c line 280. This is normally a bug in some application using the D-Bus library. libhal.c 3483 : Error unsubscribing to signals, error=The name org.freedesktop.Hal was not provided by any .service files 22: SCSI 00.0: 10602 CD-ROM (DVD) [Created at block.247] Unique ID: KD9E.JgkxTS4hgl2 Parent ID: 3p2J.gdUMCD83e+E SysFS ID: /class/block/sr0 SysFS BusID: 0:0:0:0 SysFS Device Link: /devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0 Hardware Class: cdrom Model: "HL-DT-ST DVD+-RW GSA-T40N" Vendor: "HL-DT-ST" Device: "DVD+-RW GSA-T40N" Revision: "A100" Driver: "ata_piix", "sr" Driver Modules: "ata_piix" Device File: /dev/sr0 (/dev/sg0) Device Files: /dev/sr0, /dev/scd0, /dev/disk/by-id/ata-HL-DT-ST_DVD+_-RW_GSA-T40N_K048BJ74257, /dev/disk/by-path/pci-0000:00:1f.1-scsi-0:0:0:0, /dev/cdrom, /dev/cdrw, /dev/dvd, /dev/dvdrw Device Number: block 11:0 (char 21:0) Features: DVD Config Status: cfg=new, avail=yes, need=no, active=unknown Attached to: #17 (IDE interface) Drive Speed: 31 Volume ID: "Movie" Publisher: "INTERVIDEO" Creation date: "20050424162207000" Thanks for the help. To Castro, hope this is what you meant and sorry for the comments..

  Read the article

1 2  | Next Page >