Search Results

Search found 19412 results on 777 pages for 'multiple resultsets'.

Page 102/777 | < Previous Page | 98 99 100 101 102 103 104 105 106 107 108 109  | Next Page >

  • Tomcat and IIS6 on one server, multiple websites

    - by Rafe
    Windows Server 2003 with IIS6 and Tomcat 6.0.26. Three sites running on this server. One is PHP, one is ASP and the third uses Tomcat. The first two work flawlessly. The third is being a pain. Tomcat is installed and if called on the server itself by IP address xxx.xxx.xxx.xxx:8080 shows the welcome page. Calling the same address from an external machine gives a 'could not connect' error. Calling the ip address from within the server on standard port 80 gives me an error 324 (net::ERR_EMPTY_RESPONSE). Have tried using httpcfg to force listening only on ports within the ip range I'm using in a manner similar to question 35650 located here on serverfault but with no success. There are actually ten ip addresses on this machine but I'm only using three of them at this point. Any pointers on troubleshooting this would be appreciated!

    Read the article

  • Setting multiple Apache2 VirtualHosts with the same DocumentRoot?

    - by sobi3ch
    I'm trying to accomplish something like this DocumentRoot /www/_offline.com <VirtualHost *:80> ServerName example1.com ServerAlias www.example1.com </VirtualHost> <VirtualHost *:80> ServerName example2.com ServerAlias www.example2.com DocumentRoot /www/_offline.com </VirtualHost> Is it possible to have ONE documentRoot for different domains? VirtualHost configuration: wildcard NameVirtualHosts and _default_ servers: *:80 is a NameVirtualHost default server localhost (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost localhost (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost aa.atd (/etc/apache2/sites-enabled/all-phoenix-domains:2) port 80 namevhost atd.atd (/etc/apache2/sites-enabled/all-phoenix-domains:13) port 80 namevhost test (/etc/apache2/sites-enabled/test:1) Syntax OK

    Read the article

  • Bridging Network Devices with Multiple IPs

    - by Andy
    I have a small server with a single NIC that I am trying to get a bridge functioning on so that I can run KVM. On this NIC I have a couple IPs statically assigned to it: eth0 = 192.168.1.1 eth0:1 = 192.168.1.2 eth0:2 = 192.168.1.3 eth0:3 -> Assign the bridge to this I am attempting to set up a bridge using the following instructions: sudo brctl addbr br0 sudo brctl addif br0 eth0:3 sudo ifconfig br0 192.168.1.120 netmask 255.255.255.0 up sudo route add -net 192.168.1.0 netmask 255.255.255.0 br0 sudo route add default gw 192.168.1.1 br0 sudo tunctl -b -u root -t tap0 > /dev/null sudo ifconfig tap0 up sudo brctl addif br0 tap0 However, when I do the second command: sudo brctl addif br0 eth0:3 It puts the ENTIRE eth0 device into promiscuous mode. This knocks the server offline and inaccessible by anything other than locally. Is there a way to bridge JUST eth0:3 to br0 and not put the entire device into promiscuous mode?

    Read the article

  • Amazon RDS Pros/Cons of Multiple DBs per instance

    - by Joe Flowers
    I run two completely independent websites. I am moving their MySQL databases to Amazon RDS. I'm not going to do Multi A/Z deployment - let's remove that variable from this question. I'm not sure whether to create a single RDS instance with two databases, or two Amazon RDS instances with a single database. Ignore cost for the sake of this question. I will not hit the 1 TB data limit so let's ignore that. However, it is extremely important that crashing one of the websites doesn't impact the other. Based on this document - http://docs.amazonwebservices.com/AmazonRDS/latest/UserGuide/Concepts.DBInstance.html I'm assuming that if I write terrible code that crashes one of the databases in a given RDS instance, it could possibly take down the entire RDS instance (and thus inadvertantly affect the other database). Is that correct? Thanks

    Read the article

  • Multiple PXE server same subnet

    - by Termiux
    I've been struggling with this for some time. I have a few test machines that boot from the network, they receive the boot data from the DHCP server, this tells them who is the boot server where is the file they'll boot etc. However, I need to add a second PXE server in the same subnet (create another Vlan is not an option right now). I read somewhere that I may be able to send certain parameters to certain machines based on their MAC address (this way choosing what computers boot from what server) however I cannot find how to do this, anyone knows how? this will be my solution but I cannot find the answer. My DHCP is a windows server 2003 I have 2 servers running custom flavors of Linux server as TFTP servers. Some machines use data to boot from server 1, and the others must bu able to boot from server 2. Thx

    Read the article

  • Forward one RDP port on one machine to multiple external users at the same time

    - by matnagel
    We have a windows server 2003 machine with rdp service listening on the standard port 3389. For security reasons this port is not opened on the router, but we have freesshd service running and a remote admin can login via ssh and this port is forwarded to external port 33001 for the first external user. This works great. Now we have another admin who wants to work remote (he uses a different windows account, but needs to work on the same machine.) So this is basically a ssh port forwarding question. Will the other user be able to login at the same time using the same port 33001 ? Please keep in mind that there will be a second tunnel, and this second tunnel will also use the local port 3389 on the windows server.

    Read the article

  • Hosting multiple sites on a single webapp in tomcat

    - by satish
    Scenario: I have a website - www.mydomain.com. Registered users will be given the choice of getting a permanent url to their account on mydomain.com as a subdomain like (username.mydomain.com) or they can opt to have their own domain like www.userdomain.com. So the user can access his/her account through the subdomain URL or their own hostname and the request should be forwarded to a specific url on mydomain.com. For example: xyz.mydomain.com or www.xyz.com should give the user account from www.mydomain.com/webapp/account?id=xyz. The user should be completely unaware about where the content is coming from. Setup: My website is running as a webapp in tomcat 5.5.28 with apache as the web server. I am using a VPS which means I have control over all the configuration files (apache, tomcat and dns server). Can you tell me what are the configurations needed to achieve the above scenario??

    Read the article

  • Multiple apps in one "icon" on the iPod touch [closed]

    - by Jerry
    I have researched but can't find any discussion about moving several apps into one "icon" on the iPod touch screen. I have moved 5 apps (all the same category) into one what is normally one app icon. The title on the icon reads "games" - all are games. I have all the apps jiggling and drag one game app on top of another game app - They move to be side by side and the title automatically reads "games" - is this "OK" to do - you can have nine apps in each of the 16 spaces available on each screen. Will this hurt the touch? As long as you have space (GBs) is this ok? Has anyone done or heard of this? Any help is appriecated.

    Read the article

  • What is the correct configuration for multiple apache2 vhosts and multiple php5-fpm pools?

    - by farinspace
    I have a group of sites (group A) which I would like to run using one php5-fpm pool and a second group of sites (group B) which I would like to run using a second php5-fpm pool. I can effectively define/create the pool in the fpm.conf file and I confirmed that it is running with the different user/group I've defined. However I am unclear as to how to setup the apache virtual host config. I've tried a few apache2 configurations but I seem to not be able to add the second pool. If you've done this please help.

    Read the article

  • Add jquery autocomplete on ready to multiple text inputs

    - by marcinn
    Hi, I have problem in adding autocomplete plugin to multiple text inputs in loop (no errors are returned). // get text inputs to attach autocomplete var locinputs = $('#localizations').find('input:text'); // iterate over elements and add autocomplete plugin for (var i = 0; i < locinputs.length; i++) { // asp.mvc array with special characters replacing var locNameField = locinputs[i].name.replace('[', '\\\\['); locNameField = locNameField.replace(']', '\\\\]'); locNameField = locNameField.replace('.', '\\\\.'); $('input#' + locNameField).autocomplete('<%=Url.Action("GetCity", "Localization") %>', { extraParams: { provinceId: function () { return 21; } }, dataType: 'json', parse: function (data) { var rows = new Array(); for (var i = 0; i < data.length; i++) { rows[i] = { data: data[i], value: data[i].PlaceId, result: data[i].Name }; } return rows; }, formatItem: function (row, i, n) { return row.Name; }, width: 300, mustMatch: true, multiple: true }); } There is no error on loading, I tried to debug using Firebug, elements are accessible by jquery selector

    Read the article

  • Posting data from multiple servers routing through one server to client server

    - by Swaroop Kundeti
    I have 5 webservers behind Load balancer and we have a client server at other end. Client has white listed my 5 webserver public ip so that my webservers will post a file to the client server. Here the problem is my webservers is going to increase and i cannot always ask client to make my new webserver ip's white list. So i would like to make my infra this way, my webservers will post data to the client server routing from a single server. Like assume that web-1 is main server and the remaining 4 web servers will post data to client server routing through main web-1. I was told that this can be achieved by doing IP Tunneling. But i have no idea how to do that. Would be great for any kind of help.

    Read the article

  • Multiple PPPoe connection to multiple computers via 1 modem?

    - by Koong
    I have a TP-link Wireless Router TP-WR542G and a Zyxel Prestige 650m-61 modem. I have 2 separate PPPoe accounts from my ISP. I'm thinking of using those 2 accounts simultaneously using my 1 modem. I wanted to have 1 account to be connected to the wireless router and 1 account to my computer. Is that possible? How? TQ

    Read the article

  • How do I prevent Outlook users voting multiple times

    - by Rick
    Using the voting buttons in Outlook 2007, apparently users can submit votes as many times as they like. (I have just now verified this behaviour.) Is there a way to restrict the uses to just one vote each? I've found a script online which claims to do this, but there's no way I can use a script like that across our company. I'm hoping it's just a configuration setting either in the outbound email, or in the user's Outlook client.

    Read the article

  • Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

    - by Jared
    I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

    Read the article

  • Firewall issue with multiple SIP PROXY / REGISTRAR servers

    - by MikeBrom
    Hi We have a pair of Internet-facing SIP PROXY/REGISTRAR servers (for resilienced and load-balancing). When a SIP phone registers, it will be handled by one of the REGISTRAR servers (round-robin DNS) - and since this registration is renewed, the firewall port/address translation is maintained. Therefore, when a call is to be sent back to the phone the INVITE message passes successfully through the firewall. However, it is likely that the phone may register with one of the two servers, but the INVITE may come from the other. In this situation, the call fails since there is no translation in place on the firewall. Is there a feature in the SIP protocol to facilitate this? Any other ideas? As our traffic grows, we will no doubt end-up with more than two servers - so the problem will escalate. Thanks, Mike

    Read the article

  • Nginx multiple upstream servers on the same domain via diferent url

    - by Barry
    Hello. I am trying to rout trafic to different upstream servers (that serve different applications and not for load balancing). The incoming trafic has the same domain name but different URL. Here is an example of my configuration: http { upstream backend1 { server 127.0.0.1:8080 fail_timeout=0; server 127.0.0.1:8081 fail_timeout=0; } upstream backend2 { server 127.0.0.1:8090 fail_timeout=0; server 127.0.0.1:8091 fail_timeout=0; } server { listen 80; server_name my_server.com; root /home/my_server; location /serve_me { fastcgi_pass backend1; include fastcgi_params; } location / { fastcgi_pass backend2; include fastcgi_params; } } } It seems that whatever trafic comes in (including "my_server.com/serve_me") goes to backend2. How do I make queries that start with /serve_me to be directed to backend1? Thanks, Barry.

    Read the article

  • Extending home network using multiple access point originating from another access point

    - by cyberjar09
    I have a home network with the current setup (RJ45 running from main router to access point) : +-------------+ +--------------+ | 192.168.2.1 | |192.168.2.2 | | router +--------------->access point 1| +-----^-------+ +--------------+ | | +-----+--------+ | 192.168.1.1 | | modem | +-----^--------+ | | | | +--+--+ | ISP | +-----+ However I would like to extend the network to two more floors in the house via the existing Access Point (router is too far and not reachable using a network cable, hence I need to extend using current access point). Please see diagram below : +-------------+ +--------------+ +----------------+ | 192.168.2.1 | |192.168.2.2 | | 192.168.2.3 | | router +--------------->access point 1+----------> access point 2 | +-----^-------+ +--------+-----+ +----------------+ | | | | +-----+--------+ | | 192.168.1.1 | | | modem | | +-----^--------+ | +----------------+ | +----------------> 192.168.2.4 | | | access point 3 | | +----------------+ | +--+--+ | ISP | +-----+ Q1 : is this setup possible? Q2 : if possible, will I have to do anything different from what I did to setup access point 1? edit 1 : I am trying to study the dd-wrt documentation to see which would be the correct mode of operation for me Linking Routers but Im confused because I dont see any info on how to use an existing Access point to extend the signal of the SSID. If anyone could point me to the correct wiki for how I should setup AP2 and AP3 based on AP1, it would be very helpful. For AP1, I did the following Use static IP and setup same SSID as primary wireless router use same security as primary wireless router make AP1 point to 192.168.2.1 (primary router) for DHCP Thanks in advance.

    Read the article

  • Multiple Java Versions

    - by user327486
    There are few applications which use Java 1.6.2x , few 1.7.1X and other uses 1.7.4X versions. Since we decided to push all three applications to the user .How to make the applications to use its particular version. There are few web based apps and enterprise apps which requires only a specific set of java versions which is creating issues. Os : Win 7 IE - ver 8 Work around In Progress : Trying to apply a batch file for each app to set the require java version path , but its not the required solution. Do we have any generic way which automatically maps to its required java version , instead of running batch file for each application. Looking forward your valuable suggestions.

    Read the article

  • One Mac computer with multiple network connections?

    - by Kyle Lowry
    I have a Mac (OS X 10.5) that I would like to connect to a dedicated/isolated Internet connection (one that is not connected to the LAN), and a LAN. The LAN is set up with its own, separate, Internet connection which is shared by several dozen computers (and is quite slow). I want to set it up so that the Mac uses its own dedicated Internet connection (on a different account with a different company) for its Internet access, but can still access the local area network as well. How can I configure the Mac & the network to allow this?

    Read the article

  • Sync my files across multiple computers

    - by EnderMB
    I do a lot of work on my home computer, ranging from programming, writing stored procedures and writing documentation and reporting. A lot of this work is university related and constantly swapping files across several computers is annoying at best. I have a large final-year project coming up and I'm going to be sharing this work amongst home and university and require some kind of online storage that provides version control for my programs, as well as my Word documents, PDF's and saved academic papers. Are there any good solutions for my problem?

    Read the article

  • JPA - Performance with using multiple entity manager

    - by Nguyen Tuan Linh
    My situation is: The code is not mine I have two kinds of database: one is Dad, one is Son. In Dad, I have a table to store JNDI name. I will look up Dad using JNDI, create entity manager, and retrieve this table. From these retrieved JNDI names, I will create multiple entity managers using multiple Son databases. The problem is: Son have thousands of entities. It takes each Son database around 10 minutes to load all entities. If there is 4 Son databases, it will be 40 minutes. My question: Is there any way to load all entities and use them for all entity manager? Please look at the code below For each Son JNDI: Map<String, String> puSonProperties = new HashMap<String, String>(); puSonProperties.put("javax.persistence.jtaDataSource", sonJndi); EntityManagerFactory emf = Persistence.createEntityManagerFactory("PUSon", puSonProperties); PUSon - All of them use the same persistence unit log.info("Verify entity manager for son: {0} - {1}", sonCode, emSon.find(Son_configuration.class, 0) != null ? "ok" : "failed!"); This is the actual code where the loading of all entities begins. 10 mins.

    Read the article

  • Multiple mouse settings on laptop?

    - by Jonas
    I'm wondering if this is possible. I use a macbook, running windows 7...when I don't have an external mouse connected, I leave the left/right settings of the buttons to the default. But when I plug in a mouse, I change that setting (since I use the mouse left-handed). When I unplug the mouse, I would like it to revert to the "unplugged" setting. Is there a way to get windows to remember mouse settings based on which device it's using?

    Read the article

  • Postfix multiple checks

    - by xBlue
    I want to achieve the following with Postfix: Run all emails through a black list Allow any clients sending to a list of domains Allow some clients sending to any domain This is what I have: (postfix is on 10.0.8.0 and some of the senders are 10.0.8.0 and 10.0.9.0) mynetworks_style = subnet smtpd_recipient_restrictions = check_recipient_access sqlite:/etc/postfix/access-bl.query, check_client_access hash:/etc/postfix/trusted_clients, check_recipie nt_access hash:/etc/postfix/local_domains, reject_unauth_destination, permit So, right now the black list works. File /etc/postfix/trusted_clients contains who can send anywhere (3), file /etc/postfix/local_domains contains where you can send (2). Those two are fine, they return properly. My problem is getting all three working together. Not sure if it's an ordering issue. Currently sending a test from 10.0.9.17 and I get Relay access denied. If I add: mynetworks = 10.0.8.0/24 10.0.9.0/24 then anyone can send anywhere, so #2 is not working. Postfix version is 2.10 on Ubuntu 14.04. Any ideas?

    Read the article

< Previous Page | 98 99 100 101 102 103 104 105 106 107 108 109  | Next Page >