Search Results

Search found 8233 results on 330 pages for 'unresolved external'.

Page 11/330 | < Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >

• Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

  - by jgottula

  I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

  Read the article

• Transfer Raid Drives to External Enclosure

  - by dubbeat

  I have 2 raid disks (a grand total of 360GB) in my laptop. I'm fast running out of space and want to install new drives. I've a pretty good idea how to do this. My question is what can I do with the drives that I remove? I've got lots of media files on these drives that I'd like to keep and maybe transfer back onto my laptop once I have the new drives installed. Bearing in mind that I know next to nothing about hardware how do you suggegst I go about reusing the removed drives somehow? Thanks,

  Read the article

• harddrive problem (usb external)

  - by masfenix

  Hey guys I am using a Maxtor One Touch 3 given to my by my uncle. It is connected through USB2.0 When I plug it in, XP installs it and says "the device is ready to use". But it dosnt show up on my computer. It dosn't even show up in disk mangement. I then install Acronis Disk Director (which detects it) but marks it as offline. if i try to change it to online, nothing happens. (actually the lights on the HD blink - meaning communication and goes back into offline mode). The lights on the HD return to a solid which mean "working properly". Here is a screenshot: Is there any way to extract the data off the drive? is the drive corrupt? sitll useable? edit: DISKPART screenshot: edit2: I ran Seagate diagnostic tool and this came up: Long Generic - Started 9/10/2010 6:44:36 PM Bad LBA: 0 Unable to repair Long Generic - FAIL 9/10/2010 6:46:41 PM SeaTools Test Code: 4

  Read the article

• Can I install Ubuntu 12.04 on MacBook 6.1 (Late 2009) on my external hard drive?

  - by tommywinarta

  I have no experience in installing Linux based OS on MacBook, but I already have Windows installed on my Mac. I read some articles saying I can have the Lucid Lynx installed in my Macbook 6.1 and luckily I already got the CD (which was distributed for free back then haha), my question is that can I have the 12.04 installed instead of the 10.04 and what do I need to do that? I also would like to know can I install it on my external hard drive just like installing it on a usb stick? I have viewed the how-to for installing the Lucid Lynx, is it just the same? Thanks in advance!

  Read the article

• Windows 7 explorer crashing trying to read external hard disk

  - by Mario De Schaepmeester

  I have a 1TB Western Digital hard drive which is almost full and last time I tried to plug it into my laptop, I got a Windows dialog saying "this hard drive needs to be formatted". I did not panic because I have experienced things like this before and I know it's often solved by simply re-inserting the drive. Now however, whenever I plug it in and try to browse it in explorer by going to "computer", the explorer process crashes after a while. I simply close explorer since it takes ages trying to read the disk and nothing happens. After searching on the internet, the best thing to do would be a chkdsk. I tried it via properties in explorer (which also took a good 5 minutes to open up), locks up as well, after waiting a couple of minutes it says there's no access to the disk so a chkdsk is not possible... I want to make clear that I always use safe removal before pulling out the USB cable. Last time however, safe removal just would not work and when trying to shut down Windows, the logoff screen just would not disappear (I've waited at least 10 minutes or so) and I powered off the PC by force. This may be the cause of the problems but the disk was still recognised immediately after that. I really don't want to format this thing because it contains C: clones of 3 computers and a lot of other stuff that I don't want to re-copy. What would be the best course of action? Update I got chkdsk working via the command line. I used the /F and /R options. I already got a bunch of lines saying "file record segment X is unreadable" or whatever it is in English, my OS is Dutch. It looks bad... Will chdsk repair these errors?

  Read the article

• How do I access an external hard drive plugged into my router?

  - by Shawn

  I am running Ubuntu 11.10 and I own a Netgear N600 Wireless Dual Band Router with a USB port built into it. Naturally, the router came with instructions on how to mount and view this drive with both Windows and Mac, but nothing about Linux. I have an WD Elements 1 TB external HDD that I would like to plug into the router and share across my home network. However, when I plug it in, absolutely nothing happens on my desktop. I checked on two different machines and nothing seems to indicate that the drive has been mounted (or is even seen at all) on either machine. I am fully aware that it may not be possible to do this with a Linux system, but I was hoping someone might have a suggestion. Thanks!

  Read the article

• Ubuntu 11.10 is on external HDD, how to boot (using grub4dos), and which initrd and vmlinuz to use?

  - by user198003

  I installed Ubuntu 11.10 on external HDD. How can I boot it? I used grub4dos before, and it worked with Fedora distributions. Problem I have now is that I don't know which initrd and vmlinuz files to use. Tried with one I have in /boot directory, but booting did not worked... Can you give me some ideas what to try, do i have to use different initrd and vmlinuz, or I can solve this with other solutions. Also, just to mention that boot goes to BusyBox v1.18.4 command prompt. Thank you in advance!

  Read the article

• Recovering damaged external hard disk by installing internally

  - by nfarshchi

  I had a 1TB Western Digital (My book series) 3.5" USB3. One day, the SATA to USB3 converter board was damaged and has not worked since. I decided to open the cover and use the HDD as an internal HDD. When I attached the HDD to my PC and booted up in Windows, it asked me which type of ????? I want to use "MBR or GBR" (I dont remember the exact question) I chose MBR and Windows gave me a 1TB empty Hard drive. I tried to recover with recover my files and some other recovery programs but no success. Some one told me that you should choosed GBR instead of MBR . How can I do that now? Another guy told me that the SATA to USB3 converter board is coded to save data on HDD and you can not use them internally without losing data, and I should find another SATA to USB3 board (exact same). It is impossible to find because they are not produced any more. Please help me to find a solution to bring back my data. UPDATE I have 1TB WD "Mybook" USB 3. the board that convert sata to usb3 was damaged. so when the HDD was in the box computer did not recognize it. I opened the box and remove HDD to use it internal. after connecting to my PC windows showed me one massage that I had two choice MBR or GPT I choosed MBR one and windows gave me 1TB empty new volume. I tried many recovery software to recover my data but no success. I brought it to one expert recovery company and they told me the converter board (SATA to USB3) make some encryption on data and with out that board you cannot recover any thing. so I bought another empty WD box and put the HDD inside but even after that also there is no file. I tried to recover again in this state but no success. so I have some unanswered question. does this converted boards make any password or encryption? if yes how can I solve it? does using many recovery programs affected my data? any suggestion or solution for bring back my data? I had use recovery programs such as : recover my files , EaseUS data recovery, easy recovery, test disk, Ontrack easy recovery . Note: when I was using test disk it asked me to choose which partition table I want to use. as it was I choose NTFS, does this made any change on data?

  Read the article

• Tools to backup an external hard disk

  - by Kaushik Gopal

  Hey people, What's the best method to take an exact copy of my external hard disk? A guru suggested rsync, but I was wondering if there's an easier alternative. I do remember reading somewhere that Acronis also does this. Was looking for your advice on the best option. I'm running Windows. Essentially i have an external HDD which has a lot of stuff synchronized across various pcs. I wish to take a backup of this external Hard disk (ext.HDDs aren't entirely reliable so want to keep a backup of my ext.HDD). Cheers. K

  Read the article

• Linking problems using libcurl with Visual C++ 2005: "unresolved external symbol __imp__curl_easy_se

  - by user88595

  Hi, I am planning to use libcurl in my project. I had downloaded the library source,built and integrated it in a small POC application. I am able to build and run the application without any issues with the generated libcurl.dll and libcurl_imp.lib files. Now when I integrate the same library in my project I am getting linker errors. 6foo.obj : error LNK2001: unresolved external symbol _imp_curl_easy_setopt 6foo.obj : error LNK2001: unresolved external symbol _imp_curl_easy_perform 6foo.obj : error LNK2001: unresolved external symbol _imp_curl_easy_cleanup 6foo.obj : error LNK2001: unresolved external symbol _imp_curl_global_init 6foo.obj : error LNK2001: unresolved external symbol _imp_curl_easy_init I have researched and tried all manners of workarounds like adding CURL_STATICLIB definitions , additional libraries , changing to /MT even copying the libs to the release directory but nothing seems to work. As far as I can see the only difference between approach #1 and #2 in my steps are #1 is an console application using the libcurl.dll while in my main project this is another dll which is trying to link to libcurl.dll.. Would that necessitate any change in approach? Can I use the same generated multi threaded DLL /MD file for both(Tried /MT also with no success)? Any other ideas? Following are the linker options. -------------------------------------------------Working------------------------------------------------- /OUT:"C:\SampleFTP\Release\SampleFTP.exe" /INCREMENTAL:NO /NOLOGO /LIBPATH:"C:\SampleFTP\SampleFTP\Release" /MANIFEST /MANIFESTFILE:"Release\SampleFTP.exe.intermediate.manifest" /DEBUG /PDB:"c:\SampleFTP\release\SampleFTP.pdb" /SUBSYSTEM:CONSOLE /OPT:REF /OPT:ICF /LTCG /MACHINE:X86 /ERRORREPORT:PROMPT libcurl_imp.lib kernel32.lib user32.lib gdi32.lib winspool.lib comdlg32.lib advapi32.lib shell32.lib ole32.lib oleaut32.lib uuid.lib odbc32.lib odbccp32.lib -------------------------------------------------Working------------------------------------------------- ----------------------------------------------NotWorking------------------------------------------------- /OUT:".......\nt\Win32\Release/foo__tests.dll" /INCREMENTAL:NO /NOLOGO /LIBPATH:"C:\FullLibPath\libcurl_libs" /LIBPATH:"......\nt\Win32\Release" /DLL /MANIFEST /MANIFESTFILE:".\foo_tests\Win32\Release\foo_tests.dll.intermediate.manifest" /DEBUG /PDB:".......\nt\Win32\Release/foo_tests.pdb" /OPT:REF /OPT:ICF /LTCG /IMPLIB:".......\nt\Win32\Release/foo_tests.lib" /MACHINE:X86 /ERRORREPORT:PROMPT odbc32.lib odbccp32.lib util_process.lib wsock32.lib Version.lib libcurl_imp.lib kernel32.lib user32.lib gdi32.lib winspool.lib comdlg32.lib advapi32.lib shell32.lib ole32.lib oleaut32.lib uuid.lib odbc32.lib odbccp32.lib "......\nt\win32\release\otherlib1.lib" "......\nt\win32\release\otherlib2.lib" ----------------------------------------------NotWorking-------------------------------------------------

  Read the article

• How do you cancel an external git diff?

  - by v2k

  I've got vim setup as my external diff tool: [diff] external = git_diff_wrapper !/bin/sh vimdiff "$2" "$5" Say I have 300 files that have been modified; via bash, I type "git diff". It launches 300 vimdiffs sequentially, how do I abort it?

  Read the article

• Dealing with external processes

  - by Jesse Aldridge

  I've been working on a gui app that needs to manage external processes. Working with external processes leads to a lot of issues that can make a programmer's life difficult. I feel like maintenence on this app is taking an unacceptably long time. I've been trying to list the things that make working with external processes difficult so that I can come up with ways of mitigating the pain. This kind of turned into a rant which I thought I'd post here in order to get some feedback and to provide some guidance to anybody thinking about sailing into these very murky waters. Here's what I've got so far: Output from the child can get mixed up with output from the parent. This can make both outputs misleading and hard to read. It can be hard to tell what came from where. It becomes harder to figure out what's going on when things are asynchronous. Here's a contrived example: import textwrap, os, time from subprocess import Popen test_path = 'test_file.py' with open(test_path, 'w') as file: file.write(textwrap.dedent(''' import time for i in range(3): print 'Hello %i' % i time.sleep(1)''')) proc = Popen('python -B "%s"' % test_path) for i in range(3): print 'Hello %i' % i time.sleep(1) os.remove(test_path) I guess I could have the child process write its output to a file. But it can be annoying to have to open up a file every time I want to see the result of a print statement. If I have code for the child process I could add a label, something like print 'child: Hello %i', but it can be annoying to do that for every print. And it adds some noise to the output. And of course I can't do it if I don't have access to the code. I could manually manage the process output. But then you open up a huge can of worms with threads and polling and stuff like that. A simple solution is to treat processes like synchronous functions, that is, no further code executes until the process completes. In other words, make the process block. But that doesn't work if you're building a gui app. Which brings me to the next problem... Blocking processes cause the gui to become unresponsive. import textwrap, sys, os from subprocess import Popen from PyQt4.QtGui import * from PyQt4.QtCore import * test_path = 'test_file.py' with open(test_path, 'w') as file: file.write(textwrap.dedent(''' import time for i in range(3): print 'Hello %i' % i time.sleep(1)''')) app = QApplication(sys.argv) button = QPushButton('Launch process') def launch_proc(): # Can't move the window until process completes proc = Popen('python -B "%s"' % test_path) proc.communicate() button.connect(button, SIGNAL('clicked()'), launch_proc) button.show() app.exec_() os.remove(test_path) Qt provides a process wrapper of its own called QProcess which can help with this. You can connect functions to signals to capture output relatively easily. This is what I'm currently using. But I'm finding that all these signals behave suspiciously like goto statements and can lead to spaghetti code. I think I want to get sort-of blocking behavior by having the 'finished' signal from QProcess call a function containing all the code that comes after the process call. I think that should work but I'm still a bit fuzzy on the details... Stack traces get interrupted when you go from the child process back to the parent process. If a normal function screws up, you get a nice complete stack trace with filenames and line numbers. If a subprocess screws up, you'll be lucky if you get any output at all. You end up having to do a lot more detective work everytime something goes wrong. Speaking of which, output has a way of disappearing when dealing external processes. Like if you run something via the windows 'cmd' command, the console will pop up, execute the code, and then disappear before you have a chance to see the output. You have to pass the /k flag to make it stick around. Similar issues seem to crop up all the time. I suppose both problems 3 and 4 have the same root cause: no exception handling. Exception handling is meant to be used with functions, it doesn't work with processes. Maybe there's some way to get something like exception handling for processes? I guess that's what stderr is for? But dealing with two different streams can be annoying in itself. Maybe I should look into this more... Processes can hang and stick around in the background without you realizing it. So you end up yelling at your computer cuz it's going so slow until you finally bring up your task manager and see 30 instances of the same process hanging out in the background. Also, hanging background processes can interefere with other instances of the process in various fun ways, such as causing permissions errors by holding a handle to a file or someting like that. It seems like an easy solution to this would be to have the parent process kill the child process on exit if the child process didn't close itself. But if the parent process crashes, cleanup code might not get called and the child can be left hanging. Also, if the parent waits for the child to complete, and the child is in an infinite loop or something, you can end up with two hanging processes. This problem can tie in to problem 2 for extra fun, causing your gui to stop responding entirely and force you to kill everything with the task manager. F***ing quotes Parameters often need to be passed to processes. This is a headache in itself. Especially if you're dealing with file paths. Say... 'C:/My Documents/whatever/'. If you don't have quotes, the string will often be split at the space and interpreted as two arguments. If you need nested quotes you can use ' and ". But if you need to use more than two layers of quotes, you have to do some nasty escaping, for example: "cmd /k 'python \'path 1\' \'path 2\''". A good solution to this problem is passing parameters as a list rather than as a single string. Subprocess allows you to do this. Can't easily return data from a subprocess. You can use stdout of course. But what if you want to throw a print in there for debugging purposes? That's gonna screw up the parent if it's expecting output formatted a certain way. In functions you can print one string and return another and everything works just fine. Obscure command-line flags and a crappy terminal based help system. These are problems I often run into when using os level apps. Like the /k flag I mentioned, for holding a cmd window open, who's idea was that? Unix apps don't tend to be much friendlier in this regard. Hopefully you can use google or StackOverflow to find the answer you need. But if not, you've got a lot of boring reading and frusterating trial and error to do. External factors. This one's kind of fuzzy. But when you leave the relatively sheltered harbor of your own scripts to deal with external processes you find yourself having to deal with the "outside world" to a much greater extent. And that's a scary place. All sorts of things can go wrong. Just to give a random example: the cwd in which a process is run can modify it's behavior. There are probably other issues, but those are the ones I've written down so far. Any other snags you'd like to add? Any suggestions for dealing with these problems?

  Read the article

• Porting/Writing WPF application which launches external applications to Silverlight 4 out of browse

  - by MicMit

  WPF launches certain method which calls external exe and waits , and then accesses a file which was an output of external exe. Assuming I would build this application with a consideration of porting to Silverlight 4 later what should I do ?

  Read the article

• How to update a submodule in git to the HEAD commit in that external repo

  - by cmyers

  I had problems finding the answer to this so I am posting it for posterity. The situation is, you have a git repo with a submodule (similar to an svn external). You want to update that reference to point to a different commit in the external repository. You might think 'git submodule sync' or 'git submodule update' would do that - you'd be wrong.

  Read the article

• Perl: reference to subroutine in external .pm file

  - by Pmarcoen

  I'm having some trouble figuring out how to make a reference to a subroutine in an external .pm file. Right now, I'm doing this : External file package settingsGeneral; sub printScreen { print $_[0]; } Main use settingsGeneral; my $printScreen = settingsGeneral::printScreen; &$printScreen("test"); but this result into an error: Can't use string ("1") as a subroutine ref while "strict refs" in use

  Read the article

• External XML using AS3.0

  - by vishnubhatla

  Hi, How can i load external xml file in Action Script 3.0, I have seen a tutorial http://webdeginer.blogspot.com/2010/06/external-xml-loading.html, is it right or I have to see any more tutorials. Thanks, K Swamy Vishnubhatla, webdeginer.blogspot.com.

  Read the article

• Setup a git external for remote repo

  - by Tom

  I'd create a repo which pulls in a remote repo, let's say I'd like to setup jQuery as a submodule for example git://github.com/jquery/jquery.git What would be the process of creating a repo with jQuery as a submodule and adding my own external as a remote repo. Also once this is setup, if I push / pull to my own remote, will the external remain intact?

  Read the article

• external USB HD doesn't show up on 'sudo fdisk -l' on one Ubuntu, shows up on another (both 'precise')

  - by Menelaos

  I have a 1.5TB WD external USB HDD and two Ubuntu systems, both 'precise'. When I plug the disk on system A it doesn't show up on the output of sudo fdisk -l nor is it automatically mounted (note that that wasn't always the case - it used to appear in the past). When I plug it on system B (again Ubuntu precise) it shows up when I do a sudo fdisk -l (output appended at the end) and mounts automatically just fine. What does this discrepancy point to and what kind of diagnostics should I run / tools I should use to troubleshoot the problem? I followed the suggestion I received to do a sudo tail -f /var/log/syslog and the output is the following when I plug, unplug and replug the USB cable on System A: Sep 14 23:27:09 thorin mtp-probe: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-2" Sep 14 23:27:09 thorin mtp-probe: bus: 2, device: 3 was not an MTP device Sep 14 23:28:01 thorin kernel: [ 338.994295] usb 2-2: USB disconnect, device number 3 Sep 14 23:28:04 thorin kernel: [ 341.808139] usb 2-2: new high-speed USB device number 4 using ehci_hcd Sep 14 23:28:04 thorin mtp-probe: checking bus 2, device 4: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-2" Sep 14 23:28:04 thorin mtp-probe: bus: 2, device: 4 was not an MTP device Sep 14 23:29:54 thorin AptDaemon: INFO: Quitting due to inactivity Sep 14 23:29:54 thorin AptDaemon: INFO: Quitting was requested (I guess the last two message are irrelevant). Output of sudo fdisk -l on System B $ sudo fdisk -l Disk /dev/sda: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00070db4 Device Boot Start End Blocks Id System /dev/sda1 * 2048 2905114623 1452556288 83 Linux /dev/sda2 2905116670 2930276351 12579841 5 Extended /dev/sda5 2905116672 2930276351 12579840 82 Linux swap / Solaris Disk /dev/sdb: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9c849c84 Device Boot Start End Blocks Id System /dev/sdb1 * 63 488375999 244187968+ 7 HPFS/NTFS/exFAT Disk /dev/sdg: 1500.3 GB, 1500299395072 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930272256 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0003e17f Device Boot Start End Blocks Id System /dev/sdg1 2048 2930272255 1465135104 7 HPFS/NTFS/exFAT

  Read the article

• External 1TB WD USB 3.0 HDD is not detecting. Working perfectly find in Windows

  - by Yathi

  My 1TB USB 3.0 was working fine earlier in Ubuntu as well as Windows. But lately it is not at all being detected in Ubuntu. It still works fine in Windows. I did update my Ubuntu to 12.10 but I am not sure if that caused the issue. When I connect my HDD and run dmesg | tail: [ 47.804676] usb 4-3: >Device not responding to set address. [ 48.008575] usb 4-3: >Device not responding to set address. [ 48.212421] usb 4-3: >device not accepting address 9, error -71 [ 48.324451] usb 4-3: >Device not responding to set address. [ 48.528340] usb 4-3: >Device not responding to set address. [ 48.732165] usb 4-3: >device not accepting address 10, error -71 [ 48.844138] usb 4-3: >Device not responding to set address. [ 49.048179] usb 4-3: >Device not responding to set address. [ 49.251881] usb 4-3: >device not accepting address 11, error -71 [ 49.251907] hub 4-0:1.0: >unable to enumerate USB device on port 3 The output of sudo fdisk -l is : Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00030cde Device Boot Start End Blocks Id System /dev/sda1 2048 1332981759 666489856 83 Linux /dev/sda2 1332981760 1953523711 310270976 5 Extended /dev/sda5 1332983808 1349365759 8190976 82 Linux swap / Solaris /dev/sda6 1349367808 1953523711 302077952 7 HPFS/NTFS/exFAT Disk /dev/sdb: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders, total 234441648 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000a2519 Device Boot Start End Blocks Id System /dev/sdb1 * 2048 103368703 51683328 7 HPFS/NTFS/exFAT /dev/sdb2 103368704 154568703 25600000 83 Linux /dev/sdb3 154568704 234440703 39936000 7 HPFS/NTFS/exFAT /dev/sda and /dev/sdb are my 2 internal HDDs. But the external one which should be /dev/sdc is not even being shown though it is connected and the LED on the HDD is glowing. Someone had suggested adding blacklist uas to /etc/modprobe.d/blacklist.conf. Tried that as well. But still not working. Can someone help me out.

  Read the article

• USB external drive is not recognized by any OS, how to troubleshoot in Ubuntu?

  - by Breno

  First of all I would like to inform you that I saw a question similar to mine but the error was different, so here's my problem... I have an external HD samsung s2 model of 500GB and a day to day just stopped working, tried in other systems (windows and mac) however are not recognized. In the windows device manager when I insert the usb it states that the device in question are not working properly. Well, in the logs of my ubuntu 4.12 I see the following message when I insert my usb device in: [ 2967.560216] usb 7-2: new full-speed USB device number 2 using uhci_hcd [ 2967.680182] usb 7-2: device descriptor read/64, error -71 [ 2967.904176] usb 7-2: device descriptor read/64, error -71 [ 2968.120227] usb 7-2: new full-speed USB device number 3 using uhci_hcd [ 2968.240207] usb 7-2: device descriptor read/64, error -71 [ 2968.464063] usb 7-2: device descriptor read/64, error -71 [ 2968.680087] usb 7-2: new full-speed USB device number 4 using uhci_hcd [ 2969.092085] usb 7-2: device not accepting address 4, error -71 [ 2969.208155] usb 7-2: new full-speed USB device number 5 using uhci_hcd [ 2969.624076] usb 7-2: device not accepting address 5, error -71 [ 2969.624118] hub 7-0:1.0: unable to enumerate USB device on port 2 [ 4520.240340] usb 7-1: new full-speed USB device number 6 using uhci_hcd [ 4520.364079] usb 7-1: device descriptor read/64, error -71 [ 4520.588109] usb 7-1: device descriptor read/64, error -71 [ 4520.804140] usb 7-1: new full-speed USB device number 7 using uhci_hcd [ 4520.924136] usb 7-1: device descriptor read/64, error -71 [ 4521.148083] usb 7-1: device descriptor read/64, error -71 [ 4521.364105] usb 7-1: new full-speed USB device number 8 using uhci_hcd [ 4521.776237] usb 7-1: device not accepting address 8, error -71 [ 4521.888206] usb 7-1: new full-speed USB device number 9 using uhci_hcd [ 4522.296102] usb 7-1: device not accepting address 9, error -71 [ 4522.296150] hub 7-0:1.0: unable to enumerate USB device on port 1 [ 4749.036104] usb 7-2: new full-speed USB device number 10 using uhci_hcd [ 4749.156209] usb 7-2: device descriptor read/64, error -71 [ 4749.380215] usb 7-2: device descriptor read/64, error -71 [ 4749.596206] usb 7-2: new full-speed USB device number 11 using uhci_hcd [ 4749.716409] usb 7-2: device descriptor read/64, error -71 [ 4749.940110] usb 7-2: device descriptor read/64, error -71 [ 4750.156257] usb 7-2: new full-speed USB device number 12 using uhci_hcd [ 4750.572150] usb 7-2: device not accepting address 12, error -71 [ 4750.684215] usb 7-2: new full-speed USB device number 13 using uhci_hcd [ 4751.100182] usb 7-2: device not accepting address 13, error -71 [ 4751.100224] hub 7-0:1.0: unable to enumerate USB device on port 2 Here is my system: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 08ff:2810 AuthenTec, Inc. AES2810 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 2 port SATA Controller [IDE mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 00:1f.5 IDE interface: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 2 port SATA Controller [IDE mode] (rev 02) 02:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba) 02:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04) 02:01.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 21) 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Does anyone have any clue what would be the problem?

  Read the article

• Can't call animated png script from external js file

  - by Tomas

  Hello, I'm trying to put an animated PNG dinamicaly from external .js file. First I found a simple animated png solution, which draws an animation wherever you put the code within tags, but now it looks like I don't know how to call the function properly from external file. The script is from www.squaregoldfish.co.uk/software/animatedpng, and it looks something like this: <script type="text/javascript" src="animatedpng.js"></script> <div id="pnganim" align="center"> <script> fishAnim = new AnimatedPNG('fish', 't01.png', 3, 100); fishAnim.draw(false); </script> </div> Now, I'm trying to call this from external.js file and jquery: function addFish(){ $('#pnganim').html('<script type="text/javascript" src="animatedpng.js" />'); fishAnim = new AnimatedPNG('fish', 'fish01.png', 3, 100); myFish = fishAnim.draw(false); $('#pnganim').append(myFish); } ... and it's not working. After I click a button that calls the addFish function, it opens only the first frame on a blank page. What am I doing wrong here? Thanks

  Read the article

• My Header over External Content

  - by TrivaniJoanne

  I can see this web site is somewhat over my head, but I'm having trouble finding an answer. I want to put my header, with links to other pages, over external content. Here's why: My MLM gives me a replicated web site that they maintain. I want to add links to my blog, contact info, even meta tags to the site. I though I had it done by using an iframe. I have my content at the top, and the MLM site shows up in the iframe. (here is the link www.trivanijoanne.com) The problem is that the iframe doesn't resize when the external content changes, and it is confusing for the user to need to scroll up to see the page. Also, the pdf pages don't load inside the iframe. I looked around online and see that iframes are a thing of the past. What should I be using to accomplish this task?

  Read the article

• Load external swf from a button in external swf and unload self?

  - by ChristinaR

  Hello, I am an uber n00b to flash AS3. And it is not my intention to sound like a complete moron, but honestly, I have had a hard enough time figuring out just how to load an external .swf into my main file! And now my friend is asking me if I could please add a button within the external .swf which will unload itself and load a new on in its place... I have looked around in the forums for an answer for a while now and I believe it is time for me to break down, admit defeat, and ask for help. Can someone please tell me it's not that difficult..? Surely it is possible... Thank you in advance for any advice at all! I am looking forward to the time when I can post a response here!

  Read the article

• formation an external hard disk

  - by Alex

  I am trying to format an external hard disk to FAT32 (i need it to wrok with some hardware that expects it to be in fat32). When i am trying to format it vie windows the only option I'm getting is to format it to NTFS. Another strange thing is that when i am trying to format one of my own partitions (on the hard disk that is running the OS) i can do it only in NTFS while another partition my OS can format in both NTFS and FAT32. What can cause such a bihavior and how can I format the external hard dist to FAT32?

  Read the article

• organizing external libraries and include files

  - by stijn

  Over the years my projects use more and more external libraries, and the way I did it starts feeling more and more awkward (although, that has to be said, it does work flawlessly). I use VS on Windows, CMake on others, and CodeComposer for targetting DSPs on Windows. Except for the DSPs, both 32bit and 64bit platforms are used. Here's a sample of what I am doing now; note that as shown, the different external libraries themselves are not always organized in the same way. Some have different lib/include/src folders, others have a single src folder. Some came ready-to-use with static and/or shared libraries, others were built /path/to/projects /projectA /projectB /path/to/apis /apiA /src /include /lib /apiB /include /i386/lib /amd64/lib /path/to/otherapis /apiC /src /path/to/sharedlibs /apiA_x86.lib -->some libs were built in all possible configurations /apiA_x86d.lib /apiA_x64.lib /apiA_x64d.lib /apiA_static_x86.lib /apiB.lib -->other libs have just one import library /path/to/dlls -->most of this directory also gets distributed to clients /apiA_x86.dll and it's in the PATH /apiB.dll Each time I add an external libary, I roughly use this process: build it, if needed, for different configurations (release/debug/platform) copy it's static and/or import libraries to 'sharedlibs' copy it's shared libraries to 'dlls' add an environment variable, eg 'API_A_DIR' that points to the root for ApiA, like '/path/to/apis/apiA' create a VS property sheet and a CMake file to state include path and eventually the library name, like include = '$(API_A_DIR)/Include' and lib = apiA.lib add the propertysheet/cmake file to the project needing the library It's especially step 4 and 5 that are bothering me. I am pretty sure I am not the only one facing this problem, and would like see how others deal with this. I was thinking to get rid of the environment variables per library, and use just one 'API_INCLUDE_DIR' and populating it with the include files in an organized way: /path/to/api/include /apiA /apiB /apiC This way I do not need the include path in the propertysheets nor the environment variables. For libs that are only used on windows I even don't need a propertysheet at all as I can use #pragmas to instruct the linker what library to link to. Also in the code it will be more clear what gets included, and no need for wrappers to include files having the same name but are from different libraries: #include <apiA/header.h> #include <apiB/header.h> #include <apiC_version1/header.h> The withdrawal is off course that I have to copy include files, and possibly** introduce duplicates on the filesystem, but that looks like a minor price to pay, doesn't it? ** actually once libraries are built, the only thing I need from them is the include files and thie libs. Since each of those would have a dedicated directory, the original source tree is not needed anymore so can be deleted..

  Read the article

< Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >