Search Results

Search found 11380 results on 456 pages for 'cpu speed'.

Page 114/456 | < Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >

• Link rate between EMC DAE and HBA

  - by Johan Christensson

  I have a EMC DAE (KTN-STL4) drive cage directly connecconnected to a HP Proliant server using a QLogic QLE2560 HBA. I'm using copper cable between the HBA card and the DAE. On the controller card in the DAE there is a label that states "4Gb". I'm guessing that this means 4Gbit/s. But if I set the HBA card to "Auto speed" it negotiate 2Gbit/s, and if I hard set it to 4Gbit/s I end up with no link. Why is this? Isn't the DAE controller card capebel of link speed higher then 2Gbit/s or is it the copper cable that limits the speed, or is it the interface used between the DAE and Qlogic HBA that is the problem? I have been browsing for HSSDC-FC converters and they always seems to på rated at ~2Gbit/s. If this is the limit, why does it say 4Gb on the controller cards in the DAE?

  Read the article

• What is the data transfer speeds within the disk, to other devices?

  - by Kumar

  I use Debian 6 on a HP Elitbook 6930 with 2Gigs of RAM. I was copying two AVI files, 1.5 GB in total, and noticed that the data copying was done at the rate of 4MB/sec. When I copy same AVIs to my Western Digital Passport 25G USB plugin drive the data transfer speed is 11+MB/sec. This speed is different if I plugin the drive to different USB ports. Interestingly, at work I also downloaded a 16MB IE8 exe on my virtual xp, run inside Oracle Sun Virtual Box, and it was downloaded AND saved within a second. We have a high speed network at work. :-) Why and how this difference in data speeds is possible?

  Read the article

• slow network in centos5 VM with centos5 host running KVM

  - by dan

  I setup KVM following the guide here: http://www.cyberciti.biz/faq/centos-rhel-linux-kvm-virtulization-tutorial/ I setup a bridged network and it worked fine except that the transfer speed is 200KB/s instead of the gigabit speed that I get on the host machine by itself. I tried editing the guest network settings to set "model=virtio" http://wiki.libvirt.org/page/Virtio but this just moves ifconfig-eth0 to ifconfig-eth0.bak in the VM and networking doesn't work at all. I tried moving ifconfig-eth0 back and starting up eth0, which works, but now the transfer speed is ~ 60KB/s I have no idea what else to try. Any suggestions would be greatly appreciated.

  Read the article

• slow network in centos5 VM with centos5 host running KVM

  - by dan

  I setup KVM following the guide here: http://www.cyberciti.biz/faq/centos-rhel-linux-kvm-virtulization-tutorial/ I setup a bridged network and it worked fine except that the transfer speed is 200KB/s instead of the gigabit speed that I get on the host machine by itself. I tried editing the guest network settings to set "model=virtio" http://wiki.libvirt.org/page/Virtio but this just moves ifconfig-eth0 to ifconfig-eth0.bak in the VM and networking doesn't work at all. I tried moving ifconfig-eth0 back and starting up eth0, which works, but now the transfer speed is ~ 60KB/s I have no idea what else to try. Any suggestions would be greatly appreciated.

  Read the article

• How do i use a USB wifi device properly?

  - by acidzombie24

  I'll just say a few random things One usb wifi device i notice only worked when it plugged into my usb hub Another one worked but couldnt get full speed. It came with an extention cord and when i had it a few feet away i was able to (usually) get full speed I had a wifi card in a tower in the past and just about all laptops have it built in How do i use a USB wifi adapter properly? The first device didnt come with an extention cord and made no mention of bringing it away from the computer. When someone else tested the device he said he was getting full speed while it was plugged into his tower so i was pretty surpised. How do i use USB wifi devices properly?

  Read the article

• Linux's best filesystem to work with 10000's of files without overloading the system I/O

  - by mhambra

  Hi all. It is known that certain AMD64 Linuxes are subject of being unresponsive under heavy disk I/O (see Gentoo forums: AMD64 system slow/unresponsive during disk access (Part 2)), unfortunately have such one. I want to put /var/tmp/portage and /usr/portage trees to a separate partition, but what FS to choose for it? Requirements: * for journaling, performance is preffered over safe data read/write operations * optimized to read/write 10000 of small files Candidates: * ext2 without any journaling * BtrFS In Phoronix tests, BtrFS had demonstrated a good random access performance (fat better than XFS thereby it may be less CPU-aggressive). However, unpacking operation seems to be faster with XFS there, but it was tested that unpacking kernel tree to XFS makes my system to react slower for 51% disregard of any renice'd processes and/or schedulers. Why no ReiserFS? Google'd this (q: reiserfs ext2 cpu): 1 Apr 2006 ... Surprisingly, the ReiserFS and the XFS used significantly more CPU to remove file tree (86% and 65%) when other FS used about 15% (Ext3 and ... Is it same now?

  Read the article

• Freezing of computer while watching flash videos (contd)

  - by t3st

  I have asked this similar question Computer freezing while watching Flash videos from net two week before. As i mentioned in my previous problem my computer freezes while watching online videos showing 100% cpu usage. I have tried the suggestions given in that query and I have formated my whole computer and installed windows and other softwares (with latest updates) but the problem still presisting. If i watch a video online approximately after one hour my system shows very high cpu usage and when i close my browser cpu usage comes to normal(i tried to watch Cybergeddon but my computer is freezing from start,and also other youtube videos). Can you tell me whether its an hardware problem? if yes can you give any possible explanation( eg:motherboard problem,over heating etc) because i want to tell those reasons to my computer mechanic.

  Read the article

• Display aspect ratio problem on netbooks?

  - by Jian Lin

  Last night in a computer store with the midnight sale of Windows 7, I see many netbooks, all are 1024 x 600 resolution. Then when the CPU meter and the Clock gadget were added, the CPU meter looked spherical, but the clock (the second clock -- the silver one) looked somewhat oval. Later on I went to all the desktops and both the CPU meter and the clock were spherical. So do the netbook have this "aspect ratio" problem? It is not a big deal but it'd be nice to know if I get a netbook and know that it is common on the netbook. (and aware that the picture and photos will be slightly distorted). Update: All the netbooks were at 1024 x 600, which was their "native" resolution. Every single one of them showed an oval shaped clock. None of the desktop had that issue.

  Read the article

• Performance difference between compiled and binary linux distributions/packages

  - by jozko

  I was searching a lot on the internet and couldn't find an exact answer. There are distros like Gentoo (or FreeBSD) which does not come with binaries but only with source code for packages (ports). The majority of distros uses binary backages (debian, etc.). First question: How much speed increase can I expect from compiled package? How much speed increase can I get from real world packages like apache or mysql? i.e. queries per second? Second question: Does binary package means it does not use any CPU instructions that was introduced after first AMD 64bit CPU? With the 32bit packages does it mean that the package will run on 386 and basically does not use most of the modern CPU instructions? Additional info: - I am not talking about desktop, but server environment. - I dont care about compile time - I have more servers, so speed increase more than 15% is worth for using source code packages - Please no flamewars. Thank you very much

  Read the article

• Linux Kernel IRQ Routing with irqbalance / kernel options

  - by tim

  I'm trying to get my Xen Dom0 distributing the irqs in an smp enviroment. As far as I know there are 2 Options: Use irqbalance Configure the kernel without cpu hotplug support My System is Debian Squeeze, Xen 4.0.4, Kernel 3.2.31. My Problem is: irqbalance segfaults due to a changed /proc/irq* layout or irq0 missing (this seems to be a very old bug existing since Lenny) To configure a kernel without cpu hotplug support you must disable cpu powermanagement which seems to be impossible through the standard wys (make config / make menuconfig) - the option CONFIG_PM simply defaults to "Y". Any idea anyone on how to get a debian dom0 kernel with a proper irq distribution?

  Read the article

• Ubuntu: Take actions when system temperature gets too high

  - by Josh

  One of the CPU fans on my Compaq Presario laptop running Ubuntu 9.10 seems to have bit the dust. The fan is deep within the case and I intend to replace the laptop in the next 6 months so it's not worth replacing it. I have the laptop on a cooling pad and most of the time the system is fine, CPU temps around 90°-110°F. Occasionally, however, I'm seeing random lockups which I believe is due to the system overheating. How can I configure the system to: Lower the CPU speed when the temperature reaches a certain level? (I.E. 110°F) Shutdown the system when the tempature reaches a critical level? (And what would that be? 130°?)

  Read the article

• Does using a single cable to connect two switches create a bottleneck?

  - by Nick

  I realise this may be a stupid question for some, but it's something I've always wondered about. Let's say we have two gigabit switches and all of the devices on the network are also gigabit. If 10 computers connected to switch A need to transfer large amounts of data to a server on Switch B (at the same time), is the maximum transfer speed of each connection limited by the bandwidth of the connection between the two switches? In other words, would each computer only be able to transfer at a speed of one gigabit divided by the 10 machines trying to use the "bridge" between switches? If so, are there any workarounds so that every device can use it's maximum speed from point to point?

  Read the article

• HP ProCurve Port Mode Configuration Question Mark 2

  - by SvrGuy

  We have a ProCurve Switch 2810-48G (J9022A). We need to disable auto negotiation on two ports and manually configure them to be full duplex gige ports. From the web GUI, Configuration Tab, Port Configuration sub tab, I am only presented with the option to configure the port as Auto - 1000. I take this to mean, auto negotiate duplex, manually configure the speed to be gige. From the CLI when I try to set 1000-full I get the following error: Value 1000-full is not applicable to port 39 (or whatever port I try) The exact commands I have entered are: config interface 39 speed-duplex 1000-full BTW: speed-duplex auto-1000 works ( I also tried full-1000 and that did not work either) How do I manually configure the port such that it is manually configured to use full duplex, 1000 mbs?

  Read the article

• USB resets with Ubuntu 9.10

  - by Grumbel

  Since the upgrade to Ubuntu 9.10 I have issues with getting USB device resets on my Maxtor OneTouch USB harddrive: Nov 9 20:54:37 localhost kernel: [32459.100021] usb 2-2: reset high speed USB device using ehci_hcd and address 4 Nov 9 21:54:37 localhost kernel: [36059.100017] usb 2-2: reset high speed USB device using ehci_hcd and address 4 Nov 9 23:24:37 localhost kernel: [41459.112025] usb 2-2: reset high speed USB device using ehci_hcd and address 4 The device itself continues to work fine, the resets however wake the device out of its sleep state and thus cause it to spin up, which is very annoying. Interestingly, as the log shows, the resets happen at pretty regular intervals (i.e. one hour or half an hour), not randomly. An USB card reader seems to have the same issues, while another USB harddrive from a different manufactor works fine on the same PC. What could be causing this and how could I fix it?

  Read the article

• Super-silent (mid tower) case and fan combo

  - by Dennis G.

  I want to build a HTPC for music/video/blu-ray playback (no gaming). I don't need an expensive HTPC case but just want to go with a standard medium tower case. However, I want it to be super silent so it doesn't make any annoying fan/disk noises when I watch movies. Ideally, it shouldn't make any noticeable noise at all. I understand that choosing a board, CPU and graphic card that run cool and don't consume a lot of power is important for designing a quiet machine, and I think I got that covered. However, there are so many choices in regards to cases, fans and power supplies that it's hard to get started. What are your recommendations for a case/fan (cpu+case)/power supply combination that run absolutely silent and can cool a standard Intel system with a low-power (possibly passively cooled) graphic card? I'm usually a fan of Antec cases, would an Antec Mini P180 be a good starting point? If so, which case fans, CPU fan and power supply would you recommend?

  Read the article

• Distributed computing for a company? Is there such a 'free' thing?

  - by Jakub

  I am new to the whole distributed computing / cloud thing. But I had an idea at work for our multimedia stuff like movie encoding / cpu intensive things tasks (which sometimes take a few hours). Is there a 'free' (linux?) way to go about using a Windows machine, and offsetting those cpu cycles for that task to say 10 servers that are generally idle (cpu wise)? I'm just curious if there is a way to do this or am I just grasping at straws here. My thought is that a 'cloud' setup would achieve this, however like I stated initially, I am a total newbie when it comes to it. This is just an idea, looking for some thoughts? Anyone achieve this?

  Read the article

• Flash player, HD videos and games are choppy

  - by Aimad Majdou

  I have a problem with flash player. HD videos from Youtube or Vimeo and flash games do not play smoothly. I'm using Flash player 11, Windows 7 Sp1, and my graphic card is Intel GMA 4500. Device Manager shows me that all drivers are installed on my computer, so i don't have any problems with drivers. When I run Google chrome, Resource Monitor shows me 15% ~ 40 % of CPU Usage and 40% used Physical Memory, but when I watch a video on Youtube or play a Flash game, the Resource Monitor shows 70% - 90% CPU Usage. Also, when I run some HD Video (Frame width : 1920, Frame height : 1080) on my computer, Device Manager shows me 80% ~ 100% of CPU Usage. before I Reinstall Windows 7, HD Videos and flash games were play smoothly I hadn't any problem with them !! I hope all these informations are enough to answer my question.

  Read the article

• Is there any way to use arrays in a puppet module (not in template)?

  - by KARASZI István

  I want to use puppet to manage a hadoop cluster. On the machines we have several directories which must be created and set permissions. But i'm unable to add array values for defined methods. define hdfs_site( $dirs ) { file { $dirs: ensure => directory, owner => "hadoop", group => "hadoop", mode => 755; } file { "/opt/hadoop/conf/hdfs-site.xml": content => template("hdfs-site.xml.erb"), owner => "root", group => "root", mode => 644; } } define hadoop_slave( $mem, $cpu, $dirs ) { hadoop_base { mem => $mem, cpu => $cpu, } hdfs_site { dirs => $dirs, } } hadoop_base is similar to hdfs_site. Thanks!

  Read the article

• Multiple CD writer taking long to burn

  - by Mirage

  I have installed 6 DVD writers in Tower case. I am using Alcohol Software to burn multiple CDS. I have seen that about 4 dvd/cd writer finish recording early but some take long time finish and their speed is around 7x. Its not that those are the only writers doing that, some times other writer write slowly. But there are always 1 or 2 writer which takes about 25 min to write the 700Mb cd and some finish in 5 mins Why is that. All writers can write upto 40px speed. Which thing determines the speed

  Read the article

• Is there an application I can run that will tell me how fast my computer is running?

  - by Robert Hume

  At work I log into a virtual Windows machine. I'm told it runs as fast as a PC, but I'm skeptical. Is there an application I can run on the machine that will tell me how faster the machine is actually running? It would be nice if it ran on Windows and on Mac. Updating with more details -- I was asked "why does it matter" -- here's why: It matters because I'm a programmer and I need as much speed (CPU and memory) as possible to do my work. IMO, the virtual machine is noticeably slower than a basic $800 PC would be, but I need a way a proving it. Websites like Bandwidthtest.com can show me my internet speed, so I'm wondering if there's an app that can test my computer's speed.

  Read the article

• Windows 7 - sharing file - slow seek time?

  - by progtick

  I do not want to copy the files. I simply have video files (.flv) on one computer and I would like another computer user to watch them without copying. Playback is fine, but seek time (as in if you move the cursor to skip some portion of the video) takes forever! I thought wireless speed might be the culprit, so I wired the two computer. Maybe I saw some improvement but still so bad. It's 1 Gbps! (I know real speed will vary, but before I monitor real speed and such, do I have reasonable issue? Or am I bound to have very slow seek time?) What is going on? I must mention some of these files are huge!

  Read the article

• Is computer's DRAM size not as important once we get a Solid State Drive?

  - by Jian Lin

  I am thinking of getting a Dell X11 netbook, and it can go up to 8GB of DRAM, together with a 256GB Solid State Drive. So in that case, it can handle quite a bit of Virtual PC running Linux, and Win XP, etc. But is the 8GB of RAM not so important any more. Won't 2GB or 4GB be quite good if a Solid State Hard drive is used? I think the most worried thing is that the memory is not enough and the less often used data is swapped to the pagefile on hard disk and it will become really slow, but with SDD drive, the problem is a lot less of a concerned? Is there a comparison as to, if DRAM speed is n, then SDD drive speed is how many n and hard disk speed is how many n just as a ball park comparison?

  Read the article

• Hypertransport sync flood error

  - by Carl B

  What is it? And what causes it? Is it only for uncorrectable DIMM Errors(Troubleshooting DIMM errors)? When an UCE occurs, the memory controller causes an immediate reboot of the system. During reboot, the BIOS checks the Machine Check registers and determines that the previous reboot was due to an UCE, then reports this in POST after the memtest stage: A Hypertransport Sync Flood occurred on last boot 3 BIOS reports this event in the service processor’s system event log (SEL) as shown in the sample IPMItool output There are what seems to be some suggested answers to include Bad Caps Bios verisons (happens in one version not the other) Graphics card issues Lack of power to the CPU The list of possible generators seems to target everything but the computer case. System Specs: Windows Home Premium 64 Motherboard - MSI790FX-GD70 (MS7577) / Bios v 1.9 (American Megatrensa Inc) Ram - Patriot G Series ‘Sector 5’ Edition 4GB DDR3 1600 CPU - AMD Phenom II X2 555 Black Edition Callisto 3.2GHz Socket AM3 80W (Note: unlocked 2 cores CPU Z ids it as phenom II x4 B55) Graphics - 2 x Radeon 5750 in crossfire PSU - ABS 900w HDDs - 2 Seagate 1.5 TB Sata SSD - 1 OCZ 120 GB Vertex Plus R2

  Read the article

• Ubuntu: Take actions when system temperature gets too high

  - by Josh

  One of the CPU fans on my Compaq Presario laptop running Ubuntu 9.10 seems to have bit the dust. The fan is deep within the case and I intend to replace the laptop in the next 6 months so it's not worth replacing it. I have the laptop on a cooling pad and most of the time the system is fine, CPU temps around 90°-110°F. Occasionally, however, I'm seeing random lockups which I believe is due to the system overheating. How can I configure the system to: Lower the CPU speed when the temperature reaches a certain level? (I.E. 110°F) Shutdown the system when the tempature reaches a critical level? (And what would that be? 130°?)

  Read the article

• Any opinions on Paragon's NTFS for Mac solution?

  - by AngryHacker

  I am currently using the free NTFS-3G to access my NTFS drive from the Mac. It seems pretty stable (except once in the very beginning, it locked up the Mac and corrupted my NTFS drive, which I then fixed with chkdsk from a PC). However, speed is NOT one of its virtues. I've been looking at buying Paragon NTFS for Mac OS X 7.0. Their product comparison PDF claims nearly double the speed (vs NTFS-3G) in almost every category (read, write, etc...). Can someone tell me whether the product is stable and whether the speed claims are true.

  Read the article

< Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >