Search Results

Search found 15595 results on 624 pages for 'ip forward'.

Page 127/624 | < Previous Page | 123 124 125 126 127 128 129 130 131 132 133 134  | Next Page >

• DHCP for Multiple Subnets

  - by TheD

  So this is the current setup - essentially I would like to get my DHCP server, serving DHCP requests for two seperate subnets. Netgear DG834G acting as a modem connected to a Sonicwall Pro 2040. X0 - LAN - 192.168.1.0/24 X1 - WAN - <WAN-IP> X2 - WLAN - 192.168.10.0/24 At the moment, I have a 2008R2 server with DHCP installed, with an IP address on the 192.168.1.0/24 range handling DHCP fine for this subnet. The Sonicwall is configured correctly - anything connected to the WLAN has Full Allow to anything in the LAN, and vice versa but it will not lease an IP from my Server. I've also added another IP address to the server, so the physical NIC now has two IP's: 192.168.1.2 and 192.168.10.2 with a DHCP scope configured for each. Still no luck! Any ideas? Thanks!

  Read the article

• Connecting to VPN / proxy with different port number

  - by user779159

  I have an IP address, port, username, and password for one of those VPN / proxy services that allows you to use an IP address other than what your ISP gives you, but in the 'Edit Connections VPN' GUI I don't see where to enter a port. I enter the IP address under 'Gateway' and the username and password where it asks for it, but it doesn't work. I try to enter it with the IP address ending with a colon, followed by the port, but that doesn't work either (e.g. "1.1.1.1:9999"). Any idea how I could make it work? I'm using Ubuntu 12.04 LTS. Thanks.

  Read the article

• iptables question

  - by RubyFreak

  i have a small network, with one valid IP and a firewall with 3 network interfaces (LAN, WAN, DMZ). I want to enable PAT on this valid IP to redirect http traffic to a server in my DMZ. (done) I want to enable MASQ on this ip from traffic that comes from my LAN (done) I want from my LAN as well to access my http server at DMZ. (partially) Question: in the above scenario, i cannot from my LAN, to access my http server in the DMZ, since it has the IP used by the MASQ (the only valid ip that i have). What would be the best option to solve this problem? network interfaces: eth0 (WAN) eth1 (DMZ) eth2 (LAN) /sbin/iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE /sbin/iptables -A FORWARD --o eth1 -d 2.2.2.2 -p tcp --dport 80 -j ACCEPT /sbin/iptables -t nat -A PREROUTING -i eth0 -d 1.1.1.1 -p tcp --dport 80 -j DNAT --to 2.2.2.2 /sbin/iptables -A FORWARD -i eth0 -o eth1 -m state --state RELATED,ESTABLISHED -j ACCEPT /sbin/iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT /sbin/iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT

  Read the article

• ARP replies contain wrong MAC address

  - by Jayen

  I've got a robot running linux with wired and wireless adapters. When I boot up, it connects to the wireless fine. When I assign an IP to the wired (either statically or with DHCP), it looks like it works. As in, ifconfig shows a proper IP and route shows proper routes. However, when I do an ARP request of the wired IP, the ARP reply contains the wireless MAC. ??? There's no bridge running on the robot, so why don't I get the wired MAC??? When the wire is disconnected, the wired IP replies to ping... Why is the robot replying over the wireless interface to IP requests on the wired???

  Read the article

• Network interface selection

  - by Antonino

  Hello. Suppose I have more than a network interfaces and I want to selectively use them per application. eth0 is the standard interface with the standard gateway in the main routing table eth1 is another interface with a different gateway. Suppose I launch an application as a user "user_eth1". I used the following set of rules for iptables / ip rules. IPTABLES: iptables -t mangle -A OUTPUT -m user --uid-owner user_eth1 -j MARK --set-mark 100 iptables -t nat -A POSTROUTING -m user -uid-owner -o eth1 user_eth1 -j SNAT --to-source <eth_ipaddress> IPRULE: ip rule add fwmark 100 lookup table100 and i build "table100" as follows (no doubts on that) ip route show table main | grep -Ev ^default | while read ROUTE; do ip route add table table100 $ROUTE; done ip route add default via <default_gateway> table table100 It doesn't work at all. What's wrong with this? Thank you in advance!

  Read the article

• Redirect public traffic to a different subfolder, while local traffic remains unchanged

  - by ecnepsnai

  I would like to have local (intranet) HTTP traffic go to the /var/www/html folder while any public traffic goes to the subfolder, /var/www/html/public I've tried this configuration, with some variation, in httpd.conf <VirtualHost PRIVATE-IP> DocumentRoot /var/www/html ServerName ecn ErrorLog /var/www/logs/error/private CustomLog /var/www/logs/access/private common </VirtualHost> <VirtualHost PUBLIC-IP> DocumentRoot /var/www/html/public ServerName PUBLIC-DOMAIN-NAME ErrorLog /var/www/logs/error/public CustomLog /var/www/logs/access/public common </VirtualHost> PUBLIC-IP, PRIVATE-IP, and PUBLIC-DOMAIN name are all replaced with the correct values in the actual document. The problem is, local traffic can browse fine but remote traffic is directed to the root folder and getting 403d (because I have that folder blocked off through my .htaccess file). If I append /public to the URL it works fine.

  Read the article

• Cross-Forest Trust

  - by cdalley

  I am looking at testing a cross-domain trust we can have two domain controllers (with different forests and domain names) setup so we can move everyone onto the new domain. We do NOT run exchange on site and we do not have any links to O365 to AD currently. Onto the problem: I have setup two DCs in a Virtual Machine: They are on the same network 192.168.0.* The Windows 2003 server: Name: OLDSRVR "Clone" of our current Domain Controller IP: 192.168.0.1 Domain: internal.test.com The Windows 2012 server: Name: ADCTEST01 Brand new domain setup from scratch separate to internal.test.com Domain: internal.test2.com IP: 192.168.0.2 OLDSRVR can only see ADCTEST if it has dynamic IP set. If I set a static IP it cannot see it. If I try using the dynamic IP and try to join it gets to the end then complains "??The trust relationship between this workstation and the primary domain failed" Any ideas?

  Read the article

• Application to organize / manage installed networks

  - by vicmp3

  I was wondering if there is a Application where you can organize networks. I mean if you have installed some networks you have to note every pc's name, his ip-address and so on. Is there a Application where you can manage it? I saw the monitoring tools but that is not exactly what I'm looking for. Maybe I didnt explain me well, after all my englis his not so good :) For example if I install many different networks I write in a book how I configured them. I write pc-name ip-address ip-gateway ip-broadcast and so on for each network. It will be great if I can do it in a program to organize it well, and for example it gives me a node view of the network.

  Read the article

• Route eth0 to internet traffic and eth1 to local traffic

  - by Romain Caire

  How can I route all my internet traffic on eth0 (everything except 192.168.1.0/24) and route my local traffic through eth1 (192.168.1.0)? Here is my attempt : # Flush ALL THE THINGS. ip route flush table main # Restore the main table. I flushed it because OpenVPN does weird things to it. ip route add 127.0.0.0/8 via 127.0.0.1 dev lo ip route add 0.0.0.0/0 via 164.67.195.1 ip route add 192.168.1.0/24 via 192.168.1.1 ip route flush cache

  Read the article

• Can connect to WAN via PC but router doesnt.

  - by user16877

  I have a very strange problem regarding the office network. We are currenltly in a executive suite and when i connect to wan via ethernet cable i get dhcp assigned IP address in my network config. I hooked up the linksys router to the wall expecting it to receive all the necessary ip info but that didnt work. So we have been assigned static ip address to put in to our router later but even with the static ip router doesnt seem to connect to internet. But using the same ip address and assigning to laptop works. I m very puzzled what might be the cause of this so any help is really appreciated.

  Read the article

• How to connect two subnet with Windows Server?

  - by 9dan

  Hello, I have some work to do in a small office. This office has two separate Internet connections. One is a kind of DSL line and connected through the Internet sharing router (DHCP). One is a leased line with public IP adresses (No DHCP). This leased line provide only 30 IP addresses and the gateway is provided by the ISP. Some workers use private IP provided by the router, some workers use manually setup public IP. There is a Windows 2008 R2 server with two NICs, connected to each lines. I want to connect/merge(?)/bridge(?) two subnet with this server so that users from the different subnet can access each other. How can I accomplish this? Something like, add gateway function to this server and public IP users change the gateway to point this server.. It it possible ? Sorry for my rambling. Thanks in advance.

  Read the article

• Internet Magic (Proxy sever) windows application

  Windows application which create proxy server to share Internet over any TCP/IP network

  Read the article

• Routing between two VLANs on Single Dell 6200 Switch

  - by jenglee

  I want to be able to route between two vlans that I have created and I am not sure how to go about it. So I have created, VLAN 5 with IP Address 192.168.5.1/24 and VLAN 10 with IP Address 192.168.0.1/24 //main IP addresses that I use. How would I be able to get (for example) the IP Address 192.168.0.144 to see any ip addresses in 192.168.5.1/24? Also do you have to set a default gateway for each VLAN or do you set the default gateway for the switch.

  Read the article

• Routing using Linux with 2 NIC cards

  - by Kevin Parker

  Configured Clear OS to be in Gateway mode on a machine with two NIC cards. eth0:192.168.2.0/24 with ip 192.168.2.27 which is connected to a modem and thus have internet connectivity. eth1:192.168.122.0/24 with ip 192.168.122.10 which is connected to other machines in LAN through switch. LAN machines with network 192.168.122.0 is not getting internet.How can they get internet Through Clear OS gateway.I have enabled packet forwarding in clear os using "ip_forward=1" What am i missing?.Can you please help me in this. Following are the static routing i have added: on LAN machine1 with ip address 192.168.122.11 ip route add 192.168.2.0/24 via 192.168.122.10 dev eth0 ip route show 192.168.2.0/24 via 192.168.122.10 dev eth0 192.168.122.0/24 dev eth0 proto kernel scope link src 192.168.122.11 But still 192.168.2.0/24 network is not reachable.Where can be the problem??

  Read the article

• How two use 2 subnets on one network

  - by BGuy2010

  I have some servers at a colocation. They've given us an IP range,subnet,and gateway. Now we have run out of IP's and they've given us a new range of IP's but with a different subnet and gateway. We have a Juniper NetScreen firewall and a load balancer, and I am not sure how to proceed in order to be able to use these new IPS that are on a different subnet. Do I need to setup a new VLAN? on our firewall? I tried adding one of the new IP's on one of our servers, with the new subnet and gateway. I could ping the alternate gateway, but could not ping the assigned IP from outside or from inside.

  Read the article

• Can Ping but Cannot Telnet directly to SQL Server 2012 Cluster Nodes

  - by tresstylez

  We have a monitoring tool (Solarwinds Orion) that needs to connect to a 2-node failover SQL Server Cluster. For reasons outside of our control -- we cannot monitor the CLUSTER IP directly at this time, so we have fallen back to monitoring each cluster node IP directly. This is not working. Upon troubleshooting, we tried to test that the cluster node was listening on the proper (fixed) port by using telnet to the cluster node IP/port -- and the telnet failed. However, telnet'ing to the Cluster IP/Port was SUCCESSFUL! Each node has its own IP. Each node is listening on the identical FIXED port. Each node has Dynamic Ports disabled. Each node can be PINGED successfully from the monitoring tool. Windows Firewall is DISABLED. How can I troubleshoot why I cannot telnet to the listening port on the cluster nodes?

  Read the article

• DNS Help: Move domain, not mailserver

  - by Preserved

  I'm in the middle of launching a new website for an already-in-use domain. The domain has a complicated email system so we'd like to move that over to the new server a bit later on. Currently the domain DNS is managed by the current webhost. I plan on moving the DNS management back to Network Solutions, then point the A record to the new website's IP. However, currently the DNS has the MX record the same as the A record. When NetworkSolutions is managing the DNS, and I point the A record to the new IP, then the MX record can't be the A record.. Right now: A Record mydomain.com points to IP address 198.198.198.198 MX record mydomain.com points to IP address 198.198.198.198 What I want: A Record mydomain.com points to IP address of new server MX record somehow points to current existing mailserver Does this even make sense?

  Read the article

• how to connect virtual box os and local machine

  - by soul

  This question is in connection to this question asked by a user before: http://superuser.com/questions/73470/virtualbox-vdi-file-to-vmware On how to convert vdi to vmdk or vmx using vmware converter. How do I connect the windows xp that is in virtual box to the local computer (windows 7) in a network. Because I got this error while I tried following this instruction: Give the IP address, username and password of the remote machine that you would like to convert and then hit next I got this error in vmware converter: Unable to connect the specified host 10.0.2.15 which is the ip address of the xp machine inside virtual box. It also said that there is a network configuration problem. And when I inputted the ip address from whatismyip.com which should be the same as the ip address on local machine. I didn't get the previous error but I got another one, it said that: insufficient permissions to connect to "ip address" What solution can you suggest for this problem?

  Read the article

• How do I bridge a connection from Wi-Fi to TAP on Mac OS X? (for the emulator QEMU)

  - by penx

  I'm trying to setup a bridge between my Wi-Fi connection and an emulator (QEMU). I need a virtual machine to be on the same LAN as the host, with its own IP address. QEMU requires using a TAP (virtual network device) so I have installed tuntaposx, have it running, and can open up QEMU using a TAP: qemu-system-arm -kernel zImage.integrator -initrd arm_root.img -m 256 -net nic -net tap,ifname=tap1 -nographic -append "console=ttyAMA0" I have a script that configures the bridge once QEMU has opened up the TAP interface: sysctl -w net.link.ether.inet.proxyall=1 sysctl -w net.inet.ip.forwarding=1 sysctl -w net.inet.ip.fw.enable=1 ifconfig bridge0 create ifconfig bridge0 addm en1 ifconfig tap1 0.0.0.0 up ifconfig bridge0 addm tap1 ifconfig bridge0 up If I manually set an IP on the VM, I can ping from the VM to the host, but not from the host to the VM. Also, I can't access the rest of the network from the VM - including not being able to set an IP over DHCP. Any ideas?

  Read the article

• Setting up a copy of a site with IIS 7?

  - by SJaguar13

  I have a site running on IIS with a dyndns.org domain that points to the IP of the Windows 2008 machine hosting it. I need a copy of that site for development purposes. I set up another folder with all the files, and create a new site in IIS. I don't really have a domain for it, so I was just going to use the IP address. When I go to localhost, 127.0.0.1, or the internal IP, I get bad hostname. If I use the IP address on port 80 (the same as the real version of the site), I get 404 not found. If I use a different port so I don't have them both on the same IP with the same port, I get connection timed out. How do I go about setting this up?

  Read the article

• Issue updating domain name servers from BlueHost to AWS

  - by cowls

  I am trying to migrate my site hosting from bluehost to AWS cloud based service. I have the site up and running on AWS with an elastic IP configured, it loads fine when I specify the IP address in the browser. I have gone into Route 53 on the AWS console and created a "hosted zone" for the domain. I then created a new record set of type "A" using the IP address as the value. I have a domain name registered with bluehost. Ive logged into the bluehost account and updated the domain name servers to point to those specified in Route 53 in the AWS console. When I hit the IP address directly the site loads, however it doesn't load when using the domain name (I get a google chrome oops error page saying page is not found) I've tried using this site: http://dns.squish.net/ to debug but it seems to be giving me the correct results. fizaclegems.com 300 IN A 107.20.209.78 Where 107.20.209.78 matches the elastic IP configured in the AWS console. This is the result it gives for all 4 name servers. Am I missing a step here? Does anyone know what else I should be doing or looking for?

  Read the article

• Kloxo - Use third party nameserver

  - by LePhleg

  Here's my case: I got my domain from a registrar. I got my VPS up from a provider who also offers free DNS hosting, on their own server (separately from my VPS, IP:111.111.111.111). So I got these third-party nameservers, lets name them: ns1.provider.com ns2.provider.com and pointed my domain registrar to them. I let it propagate for 24 hours so I believe its ok. (if I ping my domain I get the IP for these nameservers - 111.111.111.111) Afterwards I headed to my providers cPanel (the one they gave me for the DNS hosting service) and changed the default A Record IP from 111.111.111.111 to the IP associated with my VPS (IP:222.222.222.222). The last step, as I see it, is to configure my VPS via Kloxo panel and add the domain. Can someone guide me how can I achieve that? Is it just enough to create a new DNS Template and add as Primary DNS "ns1.provider.com" and Secondary DNS "ns2.provider.com"? Every tutorial I found is using Kloxo to create local nameservers on the same VPS which is something I want to avoid to save resources..

  Read the article

• Iptables port mapping from two PCs to one

  - by Anton

  We have 3 PCs, two of it are connected to internet (both of it have 2 NIC) PC1: eth0 - 1.0.0.1 (external IP) eth1 - 172.16.0.1 (internal IP) PC2: eth0 - 1.0.0.2 (external IP) eth1 - 172.16.0.2 (internal IP) PC3: eth0 - 172.16.0.3 (internal IP) Now we want to map port 80 from PC1 and PC2 to PC3. But there is the problem: iptables port forwarding works well from PC1 or PC2, but only in case if PC3 have PC1 or PC2 as gateway. So, question is: can we have port mapping from both PC1 and PC2 regardless of gateway settings on PC3? Thank you in advance.

  Read the article

• iptables change destination address base on result from mysql

  - by user1812225

  I need to change destination address of tcp/ip packets based on result of execution mysql query... SELECT `score` FROM `reputation` WHERE `ip` = packet.source_ip if (score < a) then packet.destination_ip = ... else packet.destination_ip = ... What ways of solving this problem do you see? Thanks. P.S. this is important that destination host knows REAL ip address where packet came from, not IP address of firewall.

  Read the article

• Configure SQL Express 2005 for remote access

  Please follow the below steps as shown in pictures to configure SQL Server Express 2005 for remote access. Fig1: Open SQL Serve Configuration Manager Fig2: Navigate to SQL Serve 2005 N/W configuration and click on Protocols node Fig3: Enable TCP/IP Protocol Fig4: Enable Named Pipes Protocol Fig5: After enabling TCP/IP and Named Pipes protocols Fig6: Finally click on TCP/IP to configure the port number to listen N/W requests to SQL Express 2005. span.fullpost {display:none;}

  Read the article

< Previous Page | 123 124 125 126 127 128 129 130 131 132 133 134  | Next Page >