Search Results

Search found 22177 results on 888 pages for 'dell studio xps 16'.

Page 131/888 | < Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >

  • how do i fix this: the networking and wireless are enabled. but list of networks under wireless networks not available

    - by Ayesha Ahmad
    i started working with ubuntu 11.10 last year. i upgraded to 12.04 a week back. since then i have had all sorts of problems with network connection. first had to install the new driver. the hardware switch somehow got disabled then the above problem arrived. even tho the options are all enabled, the OS is not able to detect scan available network connections. also i have to bring to notice that once in a while it does get connected, can not explain how it happens. I want to fix this problem once and for all. please help. ifconfig: eth0 Link encap:Ethernet HWaddr f0:4d:a2:51:b3:c8 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:44 eth1 Link encap:Ethernet HWaddr 1c:65:9d:67:d5:e1 inet6 addr: fe80::1e65:9dff:fe67:d5e1/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:170 TX packets:0 errors:27 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:344 errors:0 dropped:0 overruns:0 frame:0 TX packets:344 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:20336 (20.3 KB) TX bytes:20336 (20.3 KB) lshw -c network *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 01 serial: 1c:65:9d:67:d5:e1 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: AR8152 v1.1 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c1 serial: f0:4d:a2:51:b3:c8 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 multicast=yes port=twisted pair resources: irq:44 memory:f0400000-f043ffff ioport:2000(size=128) iwconfig lo no wireless extensions. eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:196 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 04:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) I hope this information is of some help.

    Read the article

  • How do I force Windows 7 to recognize my Projector?

    - by user63564
    I have a new Dell XPS with an NVIDIA GeForce GT 445M and an old (several years) Epson PowerLite Cinema 550 projector. Windows 7 refuses to recognize that the projector is connected under normal conditions (I'll get to the strange condition in a moment). Here are some things that I have already tried: Confirm that the projector continues to work well on my old Windows XP laptop. Confirm that the video cable (HDMI to HDMI) is connected Make sure the Dell laptop is plugged in to wall power at all times Reboot both the computer and the projector Click "Detect" under the "Connect to an External Display" Windows dialog (no reaction) Click "Rigorous Display Detection" under NVIDIA Control Panel (dialog: none found) Checked "Force Television Detection on startup" under "My display is not shown..." in NVIDIA Control Panel (no effect) Here's where it gets weird... My projector has three states: off, standby and on. Standby means the power switch on the back is on, but the projector is effectively off (no picture, no access to menu or controls). When I plug in the HDMI cable while the projector is in standby, Windows detects the projector! It lets me switch to Duplicate, Extend, or Project Only mode, and adjusts the resolution appropriately. A new Generic Plug-n-Play monitor shows up in my device manager. A "Seiko EPSON PJ" display shows up in my NVIDIA control panel. Then if I turn my projector on, Windows no longer recognizes the display. This is true whether I turn the projector on while the HDMI cable is plugged in, or if I unplug the HDMI cable while turning on the projector. Anyone have any ideas, because I'm completely stumped...?

    Read the article

  • How do you get - Better than 1024x768 Driver for 64 bit Dell PowerEdge Server

    - by tinyJoe
    How do you get better than 1024x768 resolution? Just installed MS Server 2008 64bit on a Dell PowerEdge 64bit box (works OK - Previously running MS Server 2003 32bit) After install - gives a a max resultion of 1024x768 I want to change the reslution to 1280x1024 (Same LCD Worked OK on server 2003) When I down load a driver I get a messeage "Radeon 7000 does not recognise driver" Also have Have a new LG W1042 I'd like to use. This goes up to 1440

    Read the article

  • Compatibility of ESX 4 and LTO 3 with LSI2032 Dell Power Edge

    - by dbaur
    Hello, does anybody know something about the compatibility of an LTO 3 Tapedrive (PV HH LTO 3 400GB) attached to an LSI2032 SCSI-Controller? These devices are added to an Dell PowerEdge T610 Server which is listed in the certified Compatibility Guide. I can`t find any information for this controller and this tapdevice. Or are they automaticly compatible because they are options for an compatible Server? greetings Dennis

    Read the article

  • Pen Mouse compatibility with Office 2007 on Vista Dell Inspiron 1525

    - by Iddy
    Are there mouse pens that work with a Dell laptop running Vista and Word 2007 that allow direct input into Word using the Vista tablet functionality? Currently I can write with my mouse and the tablet OCR recognizes even that poor handwriting but if there is a pen-shaped mouse that I could just plug and play that would be great. Any brands/education etc would be greatly appreciated as I am woefully ignorant on this technology.

    Read the article

  • Install SAS/SATA backplane in Dell PowerVault 220S

    - by e151280
    Is the backplane of a Dell PowerVault 220S svc tag 3sdpcb1 (14 drive, 80 pin hot swap scsi) upgradeable to a SAS/SATA backplane & controller card replacement? The unit already seems to be quite modular, with slide-out replaceable scsi controllers/connectors on the back, and slide out redundant power supplies. With everything else so modular, the backplane would seem to be the next logically upgradeable part of this unit. Thanks in advance for your input

    Read the article

  • Unable to install sbs 2008 in DELL POWEREDGE T100 [closed]

    - by Swaminathan Shanmugam
    Still unable to install WIN SBS 2008 in DELL POWEREDGE T100 server and the long post is going on at http://social.technet.microsoft.com/Forums/en-US/winservergen/thread/aa1bc4b0-943e-4ada-8de1-e03161c8fc2c My problem is unable to install sbs 2008 in 500 GB 4k sectors hdd but installation is successful in 512 bytes sector hdd. Anybody please help to solve this issue? Installation of SBS 2008 proceeds ; atlast it is not getting completed with the error message "Windows Setup could not configure Windows on this computer’s hardware"

    Read the article

  • What is the Dell E772c CRT Screen kWh consumption

    - by r0ca
    I have a Dell CRT Screen and the only info I have is this: AC input voltage / frequency / current : 90 to 264 VAC / 50 or 60 Hz + 3 Hz / 1.5 A max. (RMS) at 120 VAC and 0.8 A max.(RMS) at 220 VAC How can I calcultate the energy consumption in Watt for an hour or better, a day. Regards, David.

    Read the article

  • Dell Optiplex GX620 > windows xp home addition OU7670

    - by Ren D
    My question is my Dell Optiplex 620 is not working properly !! when i turn it on it goes automaticaly to bios and says click on safe mode or safe network or best last start up or normal mode ?? but when i click on normal it comes back to that window then i click on safe mode and it works for about 5 min then it reboots its self every time what can i do ? i checked if there was a virus and its clean !! please help

    Read the article

  • Dell All-in-One 810 CD software will no longer install

    - by authentictech
    I have a Dell All-in-One 810 printer from years ago and only recently installed it (a few months ago). Later I had reason to uninstall and re-install the printer but whenever I connect the printer Windows installs the printer drivers from its cache without the CD. How can I remove all traces of the drivers from the cache so that it will install only from the CD and not from the Windows driver cache?

    Read the article

  • Dell PowerEdge R720 - Corrupted RAID

    - by BT643
    Apologies in advance for the lengthy question. We have a Dell PowerEdge R720 server with: 2 x 136GB SAS drives in RAID 1 for the OS (Ubuntu Server 12.04) 6 x 3TB SATA drives in RAID 5 for data A few days ago we were getting errors when trying to access files on the large RAID 5 partition. We rebooted the server and got a message about the raid controller has found a foriegn config. We've had this before, and just needed to use Dell's RAID configuration utility to import foreign config on the RAID. Last time this worked, but this time, it started doing a disk check then we got this: FSCK has returned the following: "/dev/sdb1 inode 364738 has a bad extended attribute block 7 /dev/sdb1 unexpected inconsistency run fsck manually (i.e without -a or -p options) MOUNTALL fsck /ourdatapartition [1019] terminated with status 4 MOUNTALL filesystem has errors /ourdatapartition errors where found while checking the disk drive for /ourdatapartition Press F to fix errors, I to Ignore or M for Manual Recovery" We pressed F to try and fix the errors, but it eventually errored with: Inode 275841084, i_blocks is 167080, should be 0. Fix? yes Inode 275841141 has an invalid extend node (blk 2206761006, lblk 0) Clear? yes Inode 275841141, i_blocks is 227872, should be 0. Fix? yes Inode 275842303 has an invalid extend node (blk 2206760975, lblk 0) Clear? yes .... Error storing directory block information (inode=275906766, block=0, num=2699516178): Memory allocation failed /dev/sdb1: ***** FILE SYSTEM WAS MODIFIED ***** e2fsck: aborted /dev/sdb1: ***** FILE SYSTEM WAS MODIFIED ***** mountall: fsck /ourdatapartition [1286] terminated with status 9 mountall: Unrecoverable fsck error: /ourdatapartition We noticed one of the drive lights was not lit at all, and thought this may have failed and be the problem. We replaced the drive with a spare, and tried "F" to repair it again, but we keep just getting the same error as above. In the RAID configuration utility, all drives show as "online" and "optimal". We do have this data on another replicated server, so we're not worried about "recovering" anything, we just want to get the system back online asap. The server has 64 or 32GB memory, can't remember off the top of my head, but either way, with a 14TB RAID, I think it may still not be enough. Thanks EDIT - I checked the memory usage while fsck was running as suggested and after 2 or 3 minutes, it looked like this, using up nearly all of our servers memory: When it failed after 5 minutes or so with the error in my post, the memory immediately freed up again:

    Read the article

  • Intel Centrino Advanced-N + WiMAX 6250 Drivers for Windows 8 (64 Bit) on Dell N7010

    - by kindrudekid
    I cannot seem to find or get the required drivers for Intel Centrino Advanced-N + WiMAX 6250 on windows 8 64bit on my Dell N7010 Laptop I have wifi connectivity but all i get is max G speeds and no N speeds, transfering files on mapped drives is really slow as a result, this wasnt the case before, i dont care about wimax, but even those drivers would be appreciated incase i decide to sell in future...

    Read the article

  • Bad DMA/do_IRQ errors on suspend/resume, with occasional freezing

    - by Steve Kroon
    Every time I suspend or resume my laptop (Dell Latitude E6520, bought this year), I get 2 messages of the form displayed on the console just before shutting down/starting up: [ 407.107610] ehci_hcd 0000:00:1d.0: dma_pool_free buffer-128, f6f18000/36f18000 (bad dma) On occasion, I get a message of the form: [ 3753.979066] do_IRQ: 0.177 No irq handler for vector (irq -1) On occasion, my machine freezes with a flashing Caps Lock button when suspending, after which I need to do a hard shutdown. This never happened before the messages started appearing (a while back), and I think it never happens without a do_IRQ message appearing (although I'm not sure about that). [There's nothing in the owner's manual on a flashing Caps Lock button; apparently it may be a kernel panic if the scroll lock also flashes, but the laptop doesn't have a scroll lock light, and there's no message on the console saying kernel panic.] Are these bad DMA/do IRQ messages serious, and what can I do to investigate/troubleshoot them and the freezing? Edit: I've also now received the following error messages a few times: [246943.023908] JBD: I/O error detected when updating journal superblock for sdb1. [246943.023958] Buffer I/O error on device sdb1, logical block 0 [246943.023996] EXT3-fs (sdb1): I/O error while writing superblock Edit: Output of dmesg at http://pastebin.com/ra7MTQEj ; contents of /var/log/kern.log at http://pastebin.com/i6jf0Md9 Edit: the output of some smartctl (-a, -x, --log=error, --log=xerror) instructions is available at http://paste.ubuntu.com/1088488/ . Edit (31/8/2012): Output of dmesg|grep -i ehci available at http://paste.ubuntu.com/1177246/ .

    Read the article

  • My laptop with Linux/ Ubuntu isn't working

    - by Andy Campos
    I have a dell laptop with ubuntu linux. A day I tried to start it up and a black screen just appeared that says: GNU GRUB version1.98+20100804-5ubuntu3 (and these clickable options:) -Ubuntu, with Linux 2.6.35-22-generic -Ubuntu, with Linux 2.6.35-22-generic (recovery mode) -Memory test (memtest86+) -Memory test (memtest86+, serial console 115200) When I click the first one, a bunch of text appears like: mount: mounting /dev/disk/by-uuid/8396a225... failed: invalid argument mount: mounting /dev on /root/dev failed: no such file or directory mount: mounting /sys on /root/sys failed: no such file or directory mount: mounting /proc on /root/proc failed: no such file or directory Target file system doesn't have requested /sbin/init No init found. Try passing init= bootarg Enter 'help' for a list of built-in commands BusyBox v1.15.3 (Ubuntu 1:1.15.3-1ubuntu5) built-in shell (ash) (initramfs) When I enter 'help' a bunch more incomprehensible text appears. Whenever I press the enter key all that pops up is (intetramfs) If anyone can make rhyme or reason out of this please, please help me out so it can boot up normally and i can be set. If there's some kind of special code I have to type in or something I know nothing about computers.

    Read the article

  • Ubuntu 12.04 Fails to Boot after Reboot

    - by Joe
    I have installed Ubuntu 12.04 on several Dell c6220 servers. The install was successful and all hardware is recognized. The problem that I am running into is that when issuing the reboot command or when pressing ctrl-alt-del, the server shuts down, but never comes back up. Instead, the fan revs up to full speed and stays that way until I power the server down. Once the server has been powered down via the power button, Ubuntu will boot just fine -- until the next reboot. I have found that by rebooting the server via the DRAC web interface will reboot the server correctly. I have also found that this problem does not exist with CentOS -- I can press ctrl-alt-del all day long and it always comes back up. I've tried several kernel parameters such as: reboot=bios reboot=pci reboot=acpi reboot=cold acpi=off noapic Nothing seems to work. I have also tried upgrading to kernel 3.4, but no change there, either. Has anyone run into a similar problem or any pointers on troubleshooting? Thanks, Joe

    Read the article

  • How can I extend the desktop onto an external monitor/projector?

    - by hellocatfood
    I've plugged in a projector into my laptop and I'm attempting to extend the desktop onto it (so that I can run a full screen app on the projector and have the controls on my laptop). I'm able to mirror the screens effectively (it does this by default) but I can't extend it. When I untick "Mirror screens" and press apply it asks me to log out and then back in again but it goes back to mirroring the screens. I'm able to extend desktop on to my external monitor at home, just not this projector. Is there a manual way or other way to do this other that through Monitors setting? My computer model is Dell Studio 1555: Pentium Dual Core T4300(2.1GHz,800MHz,1MB), 4096MB 800MHz DDR2 Dual Channel, 512 MB ATI Mobility RADEON HD 4570 using the ATI proprietary driver. My screen resolution is 1366x768 (16:9) The projector that it wont connect properly is a Hitachi CPX3. That page specifies that it's especially designed for projectors that use 16:10 aspect ratio, but considering my external monitor at home uses 4:3 should the differences in aspect ratio matter or be causing this error?

    Read the article

  • How to fix Black screen?

    - by stupidwhiteguy
    so I recently had my question deleted and merged into a standard how to for blank screens. I am relatively new to This type of computer work and i don't understand the steps nessary to diagnose my problem well enough to solve it so this help full how to has me feeling helpless I can use Ctrl + Alt +F1 and log in So how do I use sudo commands to fix the blank screen on my old dell? sudo lsoci -nn tells me my video card is a ATI rage 128 pro ultra tf /var/log/Xorg.0.log tells me Permission denied that is all i get Sudo apt-get install --reinstall unity tried thay also have also tried Apt-get update and upgrade Please dont close this question without providing an actual answer or if you think it is an exact duplicate provide a solution that worked for that question. I see a lot of these questions as closed and there is no real answer given I will try any solutions available and report results so that others can also solve problems not be overwhelmed by overly broad troubleshooting guides that do nothing to help solve specific issues The nomodeset change from quiet splash also yields no results on reboot I still get a blank screen this screen still has contorl alt f1 abilities but that is it contorl alt f8 causes blinking cursor and F7 gets a crazy flash with green and blue then blank screen Contorl alt f1 a log in prompt in text only when run in recovery mode with failsafe graphics its says the syestem is running in low graphics mode your screen graphics card and input device settings could not be detected correctly. You will need to configure these your self how do i do that? I got this /var/log/failsafeX-backup-120909200641.tar as the location of my log files but i have no idea how to axcess sounds work in blank screen also screen responds or flashes after log in is typed and password entered really any help is good I don't even know where to start I believe 12.04 is installed and functioning but i don't think I can see it at the end of the error log it says error setting mtrr (base= oxf0000000, size= 0x01000000, type=1) inappropriate ioctl for device(25) i have tried to provide as much info as I understand how to provide

    Read the article

  • Why does my system slow down or freeze when there is heavy disk activity?

    - by user72270
    Im a first-time user to Ubuntu-12.04 with WUBI installation. My NoteBook Information : Dell vostro 3450 : i5 2410m, 3 gb ram, intel hd3000, amd 6630m hybrid. Surfing and playing games works flawlessly, however, I'm having huge problems when installing applications and generally copying and moving files. When doing so, system is significantly slower and freezes quite often (Firefox gets bluish, sometimes even black n white). I would say that Ubuntu allocates too much resources on file transfers and installing, but even these tasks are very slow. Here is very specific example : today, i tried to move 6 GB file from win 7 installation. It was good at first, i jumped to firefox but after a while firefox started to randomly turn bluish and mouse was randomly stopping working. It was gradually worse and worse and it got to a point when firefox black n whited and mouse wasn't working at all. I raged and went for some meal, when i got back screen was black. It probably unlogged me due to inactivity, when i pushed random button to bring screen to life i had to wait few minutes to let it show me only my screen background. No log in screen, just background and working mouse. NoteBook fan was working at 100 % so I assumed that file transfer was going on and I left it to work. Nothing then changed for a full hour so I hard rebooted it. File transfer unsuccessful, It transfered hardly 2 gigs. Is this normal ? What to do in these situations ? It didn't let me load system manager and not even terminal. Thanks.

    Read the article

< Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >