Search Results

Search found 4304 results on 173 pages for 'bytes'.

Page 14/173 | < Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

  • vlans on openvz, centos 6

    - by arheops
    i have centos 6 with openvz installed on it, switch with vlan support. I need following setup: 1) eth0 on openvz have be tagged multiple vlans. 2) each virtualhost have to be in single vlan. yes,i already read wiki on openvz, but it is just not work. I have on main server interface eth0.108 and able ping address on that interface(using nootbook on untagged port vlan 108), but i not able ping address inside container. Main node: [root@box1 conf]# ifconfig eth0 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:506 errors:0 dropped:0 overruns:0 frame:0 TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68939 (67.3 KiB) TX bytes:1780 (1.7 KiB) Interrupt:16 Memory:c0000000-c0012800 eth0.108 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet addr:10.11.108.3 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:238 errors:0 dropped:0 overruns:0 frame:0 TX packets:19 errors:0 dropped:12 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:25890 (25.2 KiB) TX bytes:926 (926.0 b) eth1 Link encap:Ethernet HWaddr D0:67:E5:F4:11:61 inet addr:192.168.23.233 Bcast:192.168.23.255 Mask:255.255.255.0 inet6 addr: fe80::d267:e5ff:fef4:1161/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1967 errors:0 dropped:0 overruns:0 frame:0 TX packets:356 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:365298 (356.7 KiB) TX bytes:115007 (112.3 KiB) Interrupt:17 Memory:c2000000-c2012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:784 (784.0 b) TX bytes:784 (784.0 b) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet6 addr: fe80::1/128 Scope:Link UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:3 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) veth108.0 Link encap:Ethernet HWaddr 00:18:51:DA:94:D5 inet6 addr: fe80::218:51ff:feda:94d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:639 errors:0 dropped:0 overruns:0 frame:0 TX packets:5 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:17996 (17.5 KiB) TX bytes:308 (308.0 b) virtual node [root@pbx108 /]# ifconfig eth0.108 Link encap:Ethernet HWaddr 00:18:51:CA:B5:C5 inet addr:10.11.108.1 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::218:51ff:feca:b5c5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:685 errors:0 dropped:2 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:308 (308.0 b) TX bytes:19284 (18.8 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:683 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76288 (74.5 KiB) TX bytes:76288 (74.5 KiB) /etc/vz/conf/108.conf # RAM PHYSPAGES="0:4000M" # Swap SWAPPAGES="0:512M" # Disk quota parameters (in form of softlimit:hardlimit) DISKSPACE="200G:200G" DISKINODES="20000000:22000000" QUOTATIME="0" # CPU fair scheduler parameter CPUUNITS="4000" VE_ROOT="/vz/root/$VEID" VE_PRIVATE="/vz/private/$VEID" OSTEMPLATE="centos-6-x86_64" ORIGIN_SAMPLE="vswap-256m" NETIF="ifname=eth0.108,mac=00:18:51:CA:B5:C5,host_ifname=veth108.0,host_mac=00:18:51:DA:94:D5" NAMESERVER="8.8.8.8" HOSTNAME="pbx108.localhost" IP_ADDRESS=""

    Read the article

  • Can't re-mount existing RAID10 on Ubuntu

    - by Zoran
    I saw similar questions, but didn't find what solution to my problem. After power-cut, one of RAID10 (4 disks were) appears to be malfunctioning. I make tha array active one, but can not mount it. Always the same error: mount: you must specify the filesystem type So, here is what I have when type mdadm --detail /dev/md0 /dev/md0: Version : 00.90.03 Creation Time : Tue Sep 1 11:00:40 2009 Raid Level : raid10 Array Size : 1465148928 (1397.27 GiB 1500.31 GB) Used Dev Size : 732574464 (698.64 GiB 750.16 GB) Raid Devices : 4 Total Devices : 3 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Mon Jun 11 09:54:27 2012 State : clean, degraded Active Devices : 3 Working Devices : 3 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : 1a02e789:c34377a1:2e29483d:f114274d Events : 0.166 Number Major Minor RaidDevice State 0 8 16 0 active sync /dev/sdb 1 0 0 1 removed 2 8 48 2 active sync /dev/sdd 3 8 64 3 active sync /dev/sde At the /etc/mdadm/mdadm.conf I have by default, scan all partitions (/proc/partitions) for MD superblocks. alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes automatically tag new arrays as belonging to the local system HOMEHOST <system> instruct the monitoring daemon where to send mail alerts MAILADDR root definitions of existing MD arrays ARRAY /dev/md0 level=raid10 num-devices=4 UUID=1a02e789:c34377a1:2e29483d:f114274d ARRAY /dev/md1 level=raid1 num-devices=2 UUID=9b592be7:c6a2052f:2e29483d:f114274d This file was auto-generated... So, my question is, how can I mount md0 array (md1 has been mounted without problem) in order to preserve existing data? One more thing, fdisk -l command gives the following result: Disk /dev/sdb: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x660a6799 Device Boot Start End Blocks Id System /dev/sdb1 * 1 88217 708603021 83 Linux /dev/sdb2 88218 91201 23968980 5 Extended /dev/sdb5 88218 91201 23968948+ 82 Linux swap / Solaris Disk /dev/sdc: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x0008f8ae Device Boot Start End Blocks Id System /dev/sdc1 1 88217 708603021 83 Linux /dev/sdc2 88218 91201 23968980 5 Extended /dev/sdc5 88218 91201 23968948+ 82 Linux swap / Solaris Disk /dev/sdd: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x4be1abdb Device Boot Start End Blocks Id System Disk /dev/sde: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xa4d5632e Device Boot Start End Blocks Id System Disk /dev/sdf: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xdacb141c Device Boot Start End Blocks Id System Disk /dev/sdg: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xdacb141c Device Boot Start End Blocks Id System Disk /dev/md1: 750.1 GB, 750156251136 bytes 2 heads, 4 sectors/track, 183143616 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk identifier: 0xdacb141c Device Boot Start End Blocks Id System Warning: ignoring extra data in partition table 5 Warning: ignoring extra data in partition table 5 Warning: ignoring extra data in partition table 5 Warning: invalid flag 0x7b6e of partition table 5 will be corrected by w(rite) Disk /dev/md0: 1500.3 GB, 1500312502272 bytes 255 heads, 63 sectors/track, 182402 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x660a6799 Device Boot Start End Blocks Id System /dev/md0p1 * 1 88217 708603021 83 Linux /dev/md0p2 88218 91201 23968980 5 Extended /dev/md0p5 ? 121767 155317 269488144 20 Unknown And one more thing. When using mdadm --examine command, here ise result: mdadm -v --examine --scan /dev/sdb /dev/sdc /dev/sdd /dev/sde /dev/sdf /dev/sd ARRAY /dev/md1 level=raid1 num-devices=2 UUID=9b592be7:c6a2052f:2e29483d:f114274d devices=/dev/sdf ARRAY /dev/md0 level=raid10 num-devices=4 UUID=1a02e789:c34377a1:2e29483d:f114274d devices=/dev/sdb,/dev/sdc,/dev/sdd,/dev/sde md0 has 3 devices which are active. Can someone instruct me how to solve this issue? If it is possible, I would like not to removing faulty HDD. Please advise

    Read the article

  • Can't communicate between lan ports on openwrt router

    - by ScaryAardvark
    I've got a WBMR-HP-G300H Buffalo Airstation router on which I've installed the lates OpenWRT software. All is working well (ADSL, WIFI etc) except for one niggle. I can't communicate between lan ports. i.e. if I have one computer connected on lan port 1 and I try to ping another computer on lan port 2 then I get "destination unreachable". I can ping both computers from the router itself and can also ping each computer from a seperate laptop connected wirelessly. All computers are in the same subnet range (10.0.0.?/24). I suspect that I may need to configure a vlan on the switch but everytime I try and do this with various google'ed configuration I keep freezing out all lan-ports and I have to revert back using a wirelessly connected laptop. Here's my /etc/config/network: config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr '127.0.0.1' option netmask '255.0.0.0' config interface 'lan' option type 'bridge' option proto 'static' option netmask '255.255.255.0' option ipaddr '10.0.0.1' option _orig_ifname 'eth0 wlan0' option _orig_bridge 'true' option ifname 'eth0' config adsl-device 'adsl' option fwannex 'a' option annex 'a2p' config interface 'wan' option _orig_ifname 'nas0' option _orig_bridge 'false' option proto 'pppoa' option encaps 'vc' option atmdev '0' option vci '38' option vpi '0' option username '?????????????' option password '??????????????' Any help would be warmly received. Here's some more config stuff. root@OpenWrt:~# ifconfig -a br-lan Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 inet addr:10.0.0.1 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:226576 errors:0 dropped:346 overruns:0 frame:0 TX packets:269292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:26771676 (25.5 MiB) TX bytes:183986450 (175.4 MiB) eth0 Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifb0 Link encap:Ethernet HWaddr 36:60:EC:DF:13:A1 BROADCAST NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifb1 Link encap:Ethernet HWaddr 4A:7B:75:67:54:E0 BROADCAST NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:780 errors:0 dropped:0 overruns:0 frame:0 TX packets:780 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:58369 (57.0 KiB) TX bytes:58369 (57.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 00-24-A5-BD-66-08-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2424 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:320188 (312.6 KiB) TX bytes:0 (0.0 B) pppoa-wan Link encap:Point-to-Point Protocol inet addr:81.136.179.204 P-t-P:81.134.80.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:258894 errors:0 dropped:0 overruns:0 frame:0 TX packets:212976 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:177341656 (169.1 MiB) TX bytes:25192459 (24.0 MiB) wlan0 Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:204063 errors:0 dropped:0 overruns:0 frame:0 TX packets:245516 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:26613140 (25.3 MiB) TX bytes:162799765 (155.2 MiB) root@OpenWrt:~# brctl show bridge name bridge id STP enabled interfaces br-lan 8000.0024a5bd6608 no wlan0 eth0 root@OpenWrt:~# swconfig dev eth0 show Global attributes: enable_vlan: 0 Port 0: pvid: 0 link: port:0 link:up speed:1000baseT full-duplex txflow rxflow Port 1: pvid: 0 link: port:1 link:down Port 2: pvid: 0 link: port:2 link:down Port 3: pvid: 0 link: port:3 link:down Port 4: pvid: 0 link: port:4 link:up speed:100baseT full-duplex txflow rxflow auto Port 5: pvid: 0 link: port:5 link:up speed:100baseT full-duplex txflow rxflow auto Regards Mark.

    Read the article

  • Crash using WscRegisterForChanges.

    - by user335126
    I'm trying to use the WscRegisterForChanges with C++ function in Windows 7. Documentation located here: http://msdn.microsoft.com/en-us/library/bb432507(v=VS.85).aspx My problem is that even though the callback properly executes, the code crashes when it gets to the end of the callback's execution. Here's the code in question. It's very simple, so I'm not sure why it's crashing: #include #include #include void SecurityCenterChangeOccurred(void *param) { printf("Change occurred!\n"); } int main() { HRESULT result = S_OK; HANDLE callbackRegistration = NULL; result = WscRegisterForChanges( NULL, &callbackRegistration, (LPTHREAD_START_ROUTINE)SecurityCenterChangeOccurred, NULL); while(1) { Sleep(100); } return 0; } My call stack looks like this when the crash occurs: 00faf6e8() ntdll.dll!_TppWorkerThread@4() + 0x1293 bytes kernel32.dll!@BaseThreadInitThunk@12() + 0x12 bytes ntdll.dll!___RtlUserThreadStart@8() + 0x27 bytes ntdll.dll!__RtlUserThreadStart@8() + 0x1b bytes If I add ExitThread(0); to the end of SecurityCenterChangeOccurred, I get an error and the following trace (So I don't think I should be using ExitThread): Unhandled exception at 0x7799852b (ntdll.dll) in WscRegisterForChangesCrash.exe: 0xC000071C: An invalid thread, handle %p, is specified for this operation. Possibly, a threadpool worker thread was specified. ntdll.dll!_TpCheckTerminateWorker@4() + 0x3ca2f bytes ntdll.dll!_RtlExitUserThread@4() + 0x30 bytes WscRegisterForChangesCrash.exe!SecurityCenterChangeOccurred(void * param=0x00000000) Line 8 + 0xa bytes C++ wscapi.dll!WorkItemWrapper() + 0x19 bytes ntdll.dll!_RtlpTpWorkCallback@8() + 0xdf bytes ntdll.dll!_TppWorkerThread@4() + 0x1293 bytes kernel32.dll!@BaseThreadInitThunk@12() + 0x12 bytes ntdll.dll!___RtlUserThreadStart@8() + 0x27 bytes ntdll.dll!__RtlUserThreadStart@8() + 0x1b bytes Does anyone have any ideas why this might be happening? To trigger the crash run the program and turn the firewall on or off.

    Read the article

  • Dual booting on separate hard drives

    - by tornadorider
    I have windows XP professional installed on 1 hard drive and Ubuntu 10.10 on my second hard drive. On start up the computer completely skips the grub menu and boots straight into 10.10. I have tried running os-prober with the windows hard drive mounted and then updating grub but it didnt work. Any ideas? I have changed the boot order so that the HDD with xp on it is first however the computer still booted into linux. I tried running grub-install /dev/sda and got this /usr/sbin/grub-setup: warn: Sector 32 is already in use by FlexNet; avoiding it. This software may cause boot or other problems in future. Please ask its authors not to store data in the boot track.. /usr/sbin/grub-setup: warn: Sector 33 is already in use by FlexNet; avoiding it. This software may cause boot or other problems in future. Please ask its authors not to store data in the boot track.. Installation finished. No error reported I checked using disk utility and the code for my xp hard drive is sdb so i ran the camand grub-install /dev/sdb shich gave me this Installation finished. No error reported. So i rebooted but it still didnt work. Any other ideas? Additional info gedit /boot/grub/grub.cfg: # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga } insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 load_video insmod gfxterm fi terminal_output gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c set locale_dir=($root)/boot/grub/locale set lang=en insmod gettext if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.35-28-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux /boot/vmlinuz-2.6.35-28-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro quiet splash initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-28-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c echo 'Loading Linux 2.6.35-28-generic ...' linux /boot/vmlinuz-2.6.35-28-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-22-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux /boot/vmlinuz-2.6.35-22-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro quiet splash initrd /boot/initrd.img-2.6.35-22-generic } menuentry 'Ubuntu, with Linux 2.6.35-22-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c echo 'Loading Linux 2.6.35-22-generic ...' linux /boot/vmlinuz-2.6.35-22-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-22-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### if [ "x${timeout}" != "x-1" ]; then if keystatus; then if keystatus --shift; then set timeout=-1 else set timeout=0 fi else if sleep --interruptible 3 ; then set timeout=0 fi fi fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### sudo fdisk -l: Disk /dev/sda: 80.1 GB, 80060424192 bytes 255 heads, 63 sectors/track, 9733 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0008a483 Device Boot Start End Blocks Id System /dev/sda1 * 1 9352 75112448 83 Linux /dev/sda2 9352 9734 3068929 5 Extended /dev/sda5 9352 9734 3068928 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc5d6c5d6 Device Boot Start End Blocks Id System /dev/sdb1 1 60800 488375968+ 7 HPFS/NTFS sudo blkid /dev/sda1: UUID="d682c9bd-dd89-4827-9802-a1f921ebe21c" TYPE="ext4" /dev/sda5: UUID="09e9c2cb-d903-4f0b-a181-536951845231" TYPE="swap" /dev/sdb1: UUID="B21844EB1844AFE1" TYPE="ntfs" sudo os-prober (nothing) Boot Info Script 0.55 dated February 15th, 2010 ============================= Boot Info Summary: ============================== => Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in partition #1 for (,msdos1)/boot/grub. => Grub 2 is installed in the MBR of /dev/sdb and looks on the same drive in partition #1 for (,msdos1)/boot/grub. sda1: _________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 10.10 Boot files/dirs: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sda2: _________________________________________________________________________ File system: Extended Partition Boot sector type: Unknown Boot sector info: sda5: _________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: sdb1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows XP Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows XP Boot files/dirs: =========================== Drive/Partition Info: ============================= Drive: sda ___________________ _____________________________________________________ Disk /dev/sda: 80.1 GB, 80060424192 bytes 255 heads, 63 sectors/track, 9733 cylinders, total 156368016 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/sda1 * 2,048 150,226,943 150,224,896 83 Linux /dev/sda2 150,228,990 156,366,847 6,137,858 5 Extended /dev/sda5 150,228,992 156,366,847 6,137,856 82 Linux swap / Solaris Drive: sdb ___________________ _____________________________________________________ Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/sdb1 * 63 976,751,999 976,751,937 7 HPFS/NTFS blkid -c /dev/null: ____________________________________________________________ Device UUID TYPE LABEL /dev/sda1 d682c9bd-dd89-4827-9802-a1f921ebe21c ext4 /dev/sda2: PTTYPE="dos" /dev/sda5 09e9c2cb-d903-4f0b-a181-536951845231 swap /dev/sda: PTTYPE="dos" /dev/sdb1 B21844EB1844AFE1 ntfs /dev/sdb: PTTYPE="dos" ============================ "mount | grep ^/dev output: =========================== Device Mount_Point Type Options /dev/sda1 / ext4 (rw,errors=remount-ro,commit=0) =========================== sda1/boot/grub/grub.cfg: =========================== # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga } insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 load_video insmod gfxterm fi terminal_output gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c set locale_dir=($root)/boot/grub/locale set lang=en insmod gettext if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.35-28-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux /boot/vmlinuz-2.6.35-28-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro quiet splash initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-28-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c echo 'Loading Linux 2.6.35-28-generic ...' linux /boot/vmlinuz-2.6.35-28-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-22-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux /boot/vmlinuz-2.6.35-22-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro quiet splash initrd /boot/initrd.img-2.6.35-22-generic } menuentry 'Ubuntu, with Linux 2.6.35-22-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c echo 'Loading Linux 2.6.35-22-generic ...' linux /boot/vmlinuz-2.6.35-22-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-22-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### if [ "x${timeout}" != "x-1" ]; then if keystatus; then if keystatus --shift; then set timeout=-1 else set timeout=0 fi else if sleep --interruptible 3 ; then set timeout=0 fi fi fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. menuentry "Windows XP" { set root=(hd1,1) chainloader (hd1,1)+1 } ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### =============================== sda1/etc/fstab: =============================== # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 /dev/sda1 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=09e9c2cb-d903-4f0b-a181-536951845231 none swap sw 0 0 =================== sda1: Location of files loaded by Grub: =================== 51.7GB: boot/grub/core.img 58.5GB: boot/grub/grub.cfg 1.2GB: boot/initrd.img-2.6.35-22-generic 1.3GB: boot/initrd.img-2.6.35-28-generic 58.2GB: boot/vmlinuz-2.6.35-22-generic 51.7GB: boot/vmlinuz-2.6.35-28-generic 1.3GB: initrd.img 1.2GB: initrd.img.old 51.7GB: vmlinuz 58.2GB: vmlinuz.old =========================== Unknown MBRs/Boot Sectors/etc ======================= Unknown BootLoader on sda2 00000000 d9 ed 13 ab ff a8 33 8c 01 b2 47 99 e1 4a b1 f1 |......3...G..J..| 00000010 69 5f a7 29 a4 1a 03 9e 31 b9 45 02 71 e6 58 78 |i_.)....1.E.q.Xx| 00000020 3d f6 ee 7b 3e 33 1b 82 c6 7d cf 1a c8 e7 bc 2f |=..{>3...}...../| 00000030 b9 e1 70 75 cf 18 aa e7 d5 7e 3c f1 b4 e7 9e 3a |..pu.....~<....:| 00000040 55 38 f1 b4 ee 78 59 0b 5e f7 3c 4c 57 73 9c 2a |U8...xY.^.<LWs.*| 00000050 28 f1 19 ed 11 9c b2 19 e2 80 92 1c 7b 84 ee 0b |(...........{...| 00000060 e2 c0 ac af 0a 50 42 b9 cf 0c dc 2c 20 77 85 dc |.....PB...., w..| 00000070 8f 70 5f 7b 84 9b a1 f7 8c 2d ee 70 5c ae f7 39 |.p_{.....-.p\..9| 00000080 63 f7 09 8a ec 79 4c ed 9f cc ad 3c f8 1b 47 7d |c....yL....<..G}| 00000090 3f 97 d5 16 cb 29 45 38 25 61 36 08 de 10 93 0f |?....)E8%a6.....| 000000a0 95 4f ea 54 f9 89 ff f1 bf 9a cc bb fd b6 22 b1 |.O.T..........".| 000000b0 65 08 05 21 78 19 46 b0 24 7e fb de d4 b3 ba d6 |e..!x.F.$~......| 000000c0 ec 11 65 82 ee 10 1d 12 04 91 da 6d 67 47 ea 9b |..e........mgG..| 000000d0 6f b0 aa fb cb 67 10 64 86 e8 26 85 fb f9 50 77 |o....g.d..&...Pw| 000000e0 9d 13 9b 9e d9 11 f3 a1 50 1b 11 b7 93 79 9f ab |........P....y..| 000000f0 c1 b6 86 0f 35 ed d4 9f dc f8 db bd ed 45 3a 68 |....5........E:h| 00000100 54 68 4a 1d d1 fc b8 c9 72 b4 d7 7b 60 e7 39 2f |ThJ.....r..{`.9/| 00000110 2a 0a 4e 52 72 52 c6 e2 2a 55 6a 2a e1 82 40 71 |*.NRrR..*Uj*..@q| 00000120 11 11 e0 53 d6 ff 1b a9 c6 65 df 1e b7 15 6f a2 |...S.....e....o.| 00000130 15 02 a4 6d 19 b7 78 57 a6 ee 9e 36 08 7d 6f 7c |...m..xW...6.}o|| 00000140 fd f7 7c d5 40 ff 0f c7 97 dc aa 00 ce 8b bb dc |..|.@...........| 00000150 e2 eb 1c 50 74 d8 14 cc 9a d6 5c a2 ab f2 67 f9 |...Pt.....\...g.| 00000160 58 ed 43 79 0e 78 7a 5c a6 f8 7b e8 05 4e 62 8a |X.Cy.xz\..{..Nb.| 00000170 0a 5f 22 ee a6 38 b9 e1 32 45 97 08 cc 75 66 c6 |._"..8..2E...uf.| 00000180 b3 a2 2d 89 a1 e9 95 21 28 53 fd dd be b1 b2 a2 |..-....!(S......| 00000190 78 3f a3 c9 3d e3 31 54 88 cf 78 0d e1 21 a8 74 |x?..=.1T..x..!.t| 000001a0 06 60 9d 21 c6 7a 24 e1 cc 28 f8 98 e0 99 e3 fc |.`.!.z$..(......| 000001b0 fa 8b eb d5 56 03 20 b8 54 ba c6 ee 9f 57 00 fe |....V. .T....W..| 000001c0 ff ff 82 fe ff ff 02 00 00 00 00 a8 5d 00 00 00 |............]...| 000001d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 000001f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa |..............U.| 00000200

    Read the article

  • fd partitions gone from 2 discs, md happy with it and resyncs. How to recover ?

    - by d0nd
    Hey gurus, need some help badly with this one. I run a server with a 6Tb md raid5 volume built over 7*1Tb disks. I've had to shut down the server lately and when it went back up, 2 out of the 7 disks used for the raid volume had lost its conf : dmesg : [ 10.184167] sda: sda1 sda2 sda3 // System disk [ 10.202072] sdb: sdb1 [ 10.210073] sdc: sdc1 [ 10.222073] sdd: sdd1 [ 10.229330] sde: sde1 [ 10.239449] sdf: sdf1 [ 11.099896] sdg: unknown partition table [ 11.255641] sdh: unknown partition table All 7 disks have same geometry and were configured alike : dmesg : Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect All 7 disks (sdb1, sdc1, sdd1, sde1, sdf1, sdg1, sdh1) were used in a md raid5 xfs volume. When booting, md, which was (obviously) out of sync kicked in and automatically started rebuilding over the 7 disks, including the two "faulty" ones; xfs tried to do some shenanigans as well: dmesg : [ 19.566941] md: md0 stopped. [ 19.817038] md: bind<sdc1> [ 19.817339] md: bind<sdd1> [ 19.817465] md: bind<sde1> [ 19.817739] md: bind<sdf1> [ 19.817917] md: bind<sdh> [ 19.818079] md: bind<sdg> [ 19.818198] md: bind<sdb1> [ 19.818248] md: md0: raid array is not clean -- starting background reconstruction [ 19.825259] raid5: device sdb1 operational as raid disk 0 [ 19.825261] raid5: device sdg operational as raid disk 6 [ 19.825262] raid5: device sdh operational as raid disk 5 [ 19.825264] raid5: device sdf1 operational as raid disk 4 [ 19.825265] raid5: device sde1 operational as raid disk 3 [ 19.825267] raid5: device sdd1 operational as raid disk 2 [ 19.825268] raid5: device sdc1 operational as raid disk 1 [ 19.825665] raid5: allocated 7334kB for md0 [ 19.825667] raid5: raid level 5 set md0 active with 7 out of 7 devices, algorithm 2 [ 19.825669] RAID5 conf printout: [ 19.825670] --- rd:7 wd:7 [ 19.825671] disk 0, o:1, dev:sdb1 [ 19.825672] disk 1, o:1, dev:sdc1 [ 19.825673] disk 2, o:1, dev:sdd1 [ 19.825675] disk 3, o:1, dev:sde1 [ 19.825676] disk 4, o:1, dev:sdf1 [ 19.825677] disk 5, o:1, dev:sdh [ 19.825679] disk 6, o:1, dev:sdg [ 19.899787] PM: Starting manual resume from disk [ 28.663228] Filesystem "md0": Disabling barriers, not supported by the underlying device [ 28.663228] XFS mounting filesystem md0 [ 28.884433] md: resync of RAID array md0 [ 28.884433] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [ 28.884433] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync. [ 28.884433] md: using 128k window, over a total of 976759936 blocks. [ 29.025980] Starting XFS recovery on filesystem: md0 (logdev: internal) [ 32.680486] XFS: xlog_recover_process_data: bad clientid [ 32.680495] XFS: log mount/recovery failed: error 5 [ 32.682773] XFS: log mount failed I ran fdisk and flagged sdg1 and sdh1 as fd. I tried to reassemble the array but it didnt work: no matter what was in mdadm.conf, it still uses sdg and sdh instead of sdg1 and sdh1. I checked in /dev and I see no sdg1 and and sdh1, shich explains why it wont use it. I just don't know why those partitions are gone from /dev and how to readd those... blkid : /dev/sda1: LABEL="boot" UUID="519790ae-32fe-4c15-a7f6-f1bea8139409" TYPE="ext2" /dev/sda2: TYPE="swap" /dev/sda3: LABEL="root" UUID="91390d23-ed31-4af0-917e-e599457f6155" TYPE="ext3" /dev/sdb1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdc1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdd1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sde1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdf1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdg: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdh: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" fdisk -l : Disk /dev/sda: 40.0 GB, 40020664320 bytes 255 heads, 63 sectors/track, 4865 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8c878c87 Device Boot Start End Blocks Id System /dev/sda1 * 1 12 96358+ 83 Linux /dev/sda2 13 134 979965 82 Linux swap / Solaris /dev/sda3 135 4865 38001757+ 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc9bdc1e9 Device Boot Start End Blocks Id System /dev/sdc1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xcc356c30 Device Boot Start End Blocks Id System /dev/sdd1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xe87f7a3d Device Boot Start End Blocks Id System /dev/sde1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdf: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xb17a2d22 Device Boot Start End Blocks Id System /dev/sdf1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdg: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8f3bce61 Device Boot Start End Blocks Id System /dev/sdg1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdh: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xa98062ce Device Boot Start End Blocks Id System /dev/sdh1 1 121601 976760001 fd Linux raid autodetect I really dont know what happened nor how to recover from this mess. Needless to say the 5TB or so worth of data sitting on those disks are very valuable to me... Any idea any one? Did anybody ever experienced a similar situation or know how to recover from it ? Can someone help me? I'm really desperate... :x

    Read the article

  • How do I recieve byteArray send from Server and read 4 single bytes at a time.

    - by k80sg
    I need to receive 320 bytes of data from a server which consist of 80 4 bytes int fields. How do I receive them in bytes of 4 and display their respective int values? Thanks. Not sure if this is right for the receiving part: //for reading the data from the socket BufferedInputStream bufferinput=new BufferedInputStream(NewSocket.getInputStream()); DataInputStream datainput=new DataInputStream(bufferinput); byte[] handsize=new byte[32]; // The control will halt at the below statement till all the 32 bytes are not read from the socket. datainput.readFully(handsize);

    Read the article

  • dual boot install--no GRUB

    - by Jim Syyap
    My computer recently had a hardware upgrade and now runs on Windows 7. I decided to install Ubuntu 11.04 as dual boot using the ISO I got from ubuntu.com downloaded onto my USB stick. Restarting with the USB stick, I was able to install Ubuntu 11.04 choosing the option: Install Ubuntu 11.04 side by side with Windows 7 (or something like that). No errors were encountered on installation. However on restarting, there was no GRUB; the system went straight into Windows 7. Looking for answers, I found these: http://essayboard.com/2011/07/12/how-to-dual-boot-ubuntu-11-04-and-windows-7-the-traditional-way-through-grub-2/ http://ubuntuforums.org/showthread.php?t=1774523 Following their instructions, I got: Boot Info Script 0.60 from 17 May 2011 ============================= Boot Info Summary: =============================== => Windows is installed in the MBR of /dev/sda. => Syslinux MBR (3.61-4.03) is installed in the MBR of /dev/sdb. => Grub2 (v1.99) is installed in the MBR of /dev/sdc and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos7)/boot/grub on this drive. sda1: __________________________________________________ ________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: /grldr /bootmgr /Boot/BCD /grldr sda2: __________________________________________________ ________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /Windows/System32/winload.exe sdb1: __________________________________________________ ________________________ File system: vfat Boot sector type: SYSLINUX 4.02 debian-20101016 ...........>...r>....... ......0...~.k...~...f...M.f.f....f..8~....>2} Boot sector info: Syslinux looks at sector 1437504 of /dev/sdb1 for its second stage. SYSLINUX is installed in the directory. The integrity check of the ADV area failed. According to the info in the boot sector, sdb1 starts at sector 0. But according to the info from fdisk, sdb1 starts at sector 62. Operating System: Boot files: /boot/grub/grub.cfg /syslinux/syslinux.cfg /ldlinux.sys sdc1: __________________________________________________ ________________________ File system: ntfs Boot sector type: Windows XP Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sdc2: __________________________________________________ ________________________ File system: Extended Partition Boot sector type: - Boot sector info: sdc5: __________________________________________________ ________________________ File system: swap Boot sector type: - Boot sector info: sdc6: __________________________________________________ ________________________ File system: swap Boot sector type: - Boot sector info: sdc7: __________________________________________________ ________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 11.04 Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdc8: __________________________________________________ ________________________ File system: swap Boot sector type: - Boot sector info: Going back into Ubuntu and running sudo fdisk -l , I got these: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0002f393 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 19458 156185600 7 HPFS/NTFS Disk /dev/sdb: 2011 MB, 2011168768 bytes 62 heads, 62 sectors/track, 1021 cylinders Units = cylinders of 3844 * 512 = 1968128 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000f2ab9 Device Boot Start End Blocks Id System /dev/sdb1 * 1 1021 1962331 c W95 FAT32 (LBA) Disk /dev/sdc: 1000.2 GB, 1000202043392 bytes 255 heads, 63 sectors/track, 121600 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00261ddd Device Boot Start End Blocks Id System /dev/sdc1 * 1 60657 487222656+ 7 HPFS/NTFS /dev/sdc2 60657 121600 489527681 5 Extended /dev/sdc5 120563 121600 8337703+ 82 Linux swap / Solaris /dev/sdc6 120073 120562 3930112 82 Linux swap / Solaris /dev/sdc7 60657 119584 473328640 83 Linux /dev/sdc8 119584 120072 3923968 82 Linux swap / Solaris Should I proceed and do the following? Assuming Ubuntu 11.04 was installed on device sdb1, do this: sudo mount /dev/sdb1 /mnt Then do this: sudo grub-install--root-directory=/mnt /dev/sdb Notice there are two dashes in front of the root directory, and I'm not using sdb1 but sdb. Since the command in step 15 had reinstalled Grub 2, now we need to unmount the /mnt (i.e. sdb1) to clean up. Do this: sudo umount /mnt Reboot and remove Ubuntu 11.04 CD/DVD from disk tray. Log into Ubuntu 11.04 (you have no choice but it will make you log into Ubuntu 11.04 at this point). Open up a terminal in Ubuntu 11.04 (using real installation, not live CD/DVD). Execute this command: sudo update-grub Reboot the machine.

    Read the article

  • UTF-8 bit representation

    - by Yanick Rochon
    I'm learning about UTF-8 standards and this is what I'm learning : Definition and bytes used UTF-8 binary representation Meaning 0xxxxxxx 1 byte for 1 à 7 bits chars 110xxxxx 10xxxxxx 2 bytes for 8 à 11 bits chars 1110xxxx 10xxxxxx 10xxxxxx 3 bytes for 12 à 16 bits chars 11110xxx 10xxxxxx 10xxxxxx 10xxxxxx 4 bytes for 17 à 21 bits chars And I'm wondering, why 2 bytes UTF-8 code is not 10xxxxxx instead, thus gaining 1 bit all the way up to 22 bits with a 4 bytes UTF-8 code? The way it is right now, 64 possible values are lost (from 1000000 to 10111111). I'm not trying to argue the standards, but I'm wondering why this is so? ** EDIT ** Even, why isn't it UTF-8 binary representation Meaning 0xxxxxxx 1 byte for 1 à 7 bits chars 110xxxxx xxxxxxxx 2 bytes for 8 à 13 bits chars 1110xxxx xxxxxxxx xxxxxxxx 3 bytes for 14 à 20 bits chars 11110xxx xxxxxxxx xxxxxxxx xxxxxxxx 4 bytes for 21 à 27 bits chars ...? Thanks!

    Read the article

  • D key not working on Ubuntu

    - by Jonathan
    For some inexplicable reason the capital d key on my Ubuntu system is no longer producing output. Hitting caps lock and then d produces a D. I've tried multiple keyboards and the issue is the same. There's nothing bound to Shift+d under System Preferences Keyboard Shortcuts. xev produces the following: shift + a KeyPress event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31268952, (130,-16), root:(1000,525), state 0x10, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyPress event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31269376, (130,-16), root:(1000,525), state 0x11, keycode 38 (keysym 0x41, A), same_screen YES, XLookupString gives 1 bytes: (41) "A" XmbLookupString gives 1 bytes: (41) "A" XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31269584, (130,-16), root:(1000,525), state 0x11, keycode 38 (keysym 0x41, A), same_screen YES, XLookupString gives 1 bytes: (41) "A" XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31269608, (130,-16), root:(1000,525), state 0x11, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False shift + d KeyPress event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31102792, (115,-13), root:(985,528), state 0x10, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False FocusOut event, serial 36, synthetic NO, window 0x4c00001, mode NotifyGrab, detail NotifyAncestor FocusIn event, serial 36, synthetic NO, window 0x4c00001, mode NotifyUngrab, detail NotifyAncestor KeymapNotify event, serial 36, synthetic NO, window 0x0, keys: 2 0 0 0 0 0 0 64 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 KeyRelease event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31103104, (115,-13), root:(985,528), state 0x11, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False

    Read the article

  • Analyzing Memory Usage: Java vs C++ Negligible?

    - by Anthony
    How does the memory usage of an integer object written in Java compare\contrast with the memory usage of a integer object written in C++? Is the difference negligible? No difference? A big difference? I'm guessing it's the same because an int is an int regardless of the language (?) The reason why I asked this is because I was reading about the importance of knowing when a program's memory requirements will prevent the programmer from solving a given problem. What fascinated me is the amount of memory required for creating a single Java object. Take for example, an integer object. Correct me if I'm wrong but a Java integer object requires 24 bytes of memory: 4 bytes for its int instance variable 16 bytes of overhead (reference to the object's class, garbage collection info & synchronization info) 4 bytes of padding As another example, a Java array (which is implemented as an object) requires 48+bytes: 24 bytes of header info 16 bytes of object overhead 4 bytes for length 4 bytes for padding plus the memory needed to store the values How do these memory usages compare with the same code written in C++? I used to be oblivious about the memory usage of the C++ and Java programs I wrote, but now that I'm beginning to learn about algorithms, I'm having a greater appreciation for the computer's resources.

    Read the article

  • Capital D key not working / producing output

    - by Jonathan
    For some inexplicable reason the capital d key on my Ubuntu system is no longer producing output. Hitting caps lock and then d produces a D. I've tried multiple keyboards and the issue is the same. There's nothing bound to Shift+d under System Preferences Keyboard Shortcuts. xev produces the following: shift + a KeyPress event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31268952, (130,-16), root:(1000,525), state 0x10, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyPress event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31269376, (130,-16), root:(1000,525), state 0x11, keycode 38 (keysym 0x41, A), same_screen YES, XLookupString gives 1 bytes: (41) "A" XmbLookupString gives 1 bytes: (41) "A" XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31269584, (130,-16), root:(1000,525), state 0x11, keycode 38 (keysym 0x41, A), same_screen YES, XLookupString gives 1 bytes: (41) "A" XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31269608, (130,-16), root:(1000,525), state 0x11, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False shift + d KeyPress event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31102792, (115,-13), root:(985,528), state 0x10, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False FocusOut event, serial 36, synthetic NO, window 0x4c00001, mode NotifyGrab, detail NotifyAncestor FocusIn event, serial 36, synthetic NO, window 0x4c00001, mode NotifyUngrab, detail NotifyAncestor KeymapNotify event, serial 36, synthetic NO, window 0x0, keys: 2 0 0 0 0 0 0 64 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 KeyRelease event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31103104, (115,-13), root:(985,528), state 0x11, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False

    Read the article

  • How should I compress a file with multiple bytes that are the same with Huffman coding?

    - by Omega
    On my great quest for compressing/decompressing files with a Java implementation of Huffman coding (http://en.wikipedia.org/wiki/Huffman_coding) for a school assignment, I am now at the point of building a list of prefix codes. Such codes are used when decompressing a file. Basically, the code is made of zeroes and ones, that are used to follow a path in a Huffman tree (left or right) for, ultimately, finding a byte. In this Wikipedia image, to reach the character m the prefix code would be 0111 The idea is that when you compress the file, you will basically convert all the bytes of the file into prefix codes instead (they tend to be smaller than 8 bits, so there's some gain). So every time the character m appears in a file (which in binary is actually 1101101), it will be replaced by 0111 (if we used the tree above). Therefore, 1101101110110111011011101101 becomes 0111011101110111 in the compressed file. I'm okay with that. But what if the following happens: In the file to be compressed there exists only one unique byte, say 1101101. There are 1000 of such byte. Technically, the prefix code of such byte would be... none, because there is no path to follow, right? I mean, there is only one unique byte anyway, so the tree has just one node. Therefore, if the prefix code is none, I would not be able to write the prefix code in the compressed file, because, well, there is nothing to write. Which brings this problem: how would I compress/decompress such file if it is impossible to write a prefix code when compressing? (using Huffman coding, due to the school assignment's rules) This tutorial seems to explain a bit better about prefix codes: http://www.cprogramming.com/tutorial/computersciencetheory/huffman.html but doesn't seem to address this issue either.

    Read the article

  • Ubuntu 12.04 login screen flickers. “Could not write bytes: broken pipes”

    - by Brayn
    I use Ubuntu 12.04 x64 with a dual-boot setup. Yesterday it worked fine but this morning when I attempted to boot it gets to the login screen and then it just flickers, alternating between the login screen and the console showing boot items (mainly Apache, the last one being "Battery status" although it's a desktop) all with [OK] status. The only error that I can see is: "Could not write bytes: broken pipes" on top of the screen. The only things I can think of that could cause this are: This morning I had a removable hdd plugged in during boot time, which I usually don't have Yesterday I've installed Dwarven Fortress that requires some x32 libraries so I've installed ia32 using synaptic. As far as I know this shouldn't brake the system but I didn't reboot yesterday so I can't be sure. I've tried booting in recovery mode and tried running the utils there but still no luck. I've ran out of ideas. Thanks. EDIT: Forgot to mention that all partitions have plenty of free space EDIT2: In the end I just reinstalled Ubuntu as time was of the essence.

    Read the article

  • extreme slowness with a remote database in Drupal

    - by ceejayoz
    We're attempting to scale our Drupal installations up and have decided on some dedicated MySQL boxes. Unfortunately, we're running into extreme slowness when we attempt to use the remote DB - page load times go from ~200 milliseconds to 5-10 seconds. Latency between the servers is minimal - a tenth or two of a millisecond. PING 10.37.66.175 (10.37.66.175) 56(84) bytes of data. 64 bytes from 10.37.66.175: icmp_seq=1 ttl=64 time=0.145 ms 64 bytes from 10.37.66.175: icmp_seq=2 ttl=64 time=0.157 ms 64 bytes from 10.37.66.175: icmp_seq=3 ttl=64 time=0.157 ms 64 bytes from 10.37.66.175: icmp_seq=4 ttl=64 time=0.144 ms 64 bytes from 10.37.66.175: icmp_seq=5 ttl=64 time=0.121 ms 64 bytes from 10.37.66.175: icmp_seq=6 ttl=64 time=0.122 ms 64 bytes from 10.37.66.175: icmp_seq=7 ttl=64 time=0.163 ms 64 bytes from 10.37.66.175: icmp_seq=8 ttl=64 time=0.115 ms 64 bytes from 10.37.66.175: icmp_seq=9 ttl=64 time=0.484 ms 64 bytes from 10.37.66.175: icmp_seq=10 ttl=64 time=0.156 ms --- 10.37.66.175 ping statistics --- 10 packets transmitted, 10 received, 0% packet loss, time 8998ms rtt min/avg/max/mdev = 0.115/0.176/0.484/0.104 ms Drupal's devel.module timers show the database queries aren't running any slower on the remote DB - about 150 microseconds whether it's the local or the remote server. Profiling with XHProf shows PHP execution times that aren't out of whack, either. Number of queries doesn't seem to make a difference - we seem the same 5-10 second delay whether a page has 12 queries or 250. Any suggestions about where I should start troubleshooting here? I'm quite confused.

    Read the article

  • How to improve Windows Server 2008 R2 to handle many connections?

    - by invisal
    It has been a few days so far that I am trying to figure how to solve this problem. First of all, I am running a website with an average daily page view of 350,000. Previously, all ads management (tracking click and impression that each ads has served) and content were served in a single server with the following spec: Server 1 OS: Windows 2008 R2 64-Bit CPU: Intel® Core™ i5 - 4 cores RAM: 8 GB Storage: 2 x 1 TB hard drives Bandwidth: 10 TB per month To improve our website speed, I decided to separate the ads management script to another dedicated server because we have more than 15 advertisers to 30 advertisers per each page. Server 2 OS: Windows 2008 R2 64-Bit CPU: Intel® Core™ i5 - 4 cores RAM: 4 GB Storage: 2 x 300 GB hard drives Bandwidth: 10 TB per month The Problem The problem is that Server 1 can handle both content and ads system. Now, that I take away the ads system and put it at Server 2. Server 2 can barely serve only ads system. Test First of all, I moved 75% of the ads to Server 2. And then, perform a ping to server: ping -t xxxxx. [I did the ping for 10 minutes and its following similar pattern as below] Reply from xxxxx bytes=32 time=290ms TTL=116 Reply from xxxxx bytes=32 time=289ms TTL=116 Reply from xxxxx bytes=32 time=320ms TTL=116 Reply from xxxxx bytes=32 time=286ms TTL=116 Reply from xxxxx bytes=32 time=286ms TTL=116 Reply from xxxxx bytes=32 time=348ms TTL=116 Reply from xxxxx bytes=32 time=284ms TTL=116 Then, I moved 100% of the ads to Server 2. Then, perform a ping to server again. [I did the ping for 10 minutes and its following similar pattern as below] Reply from xxxxx bytes=32 time=290ms TTL=116 Request timed out Reply from xxxxx bytes=32 time=320ms TTL=116 Reply from xxxxx bytes=32 time=286ms TTL=116 Request timed out Request timed out Reply from xxxxx bytes=32 time=284ms TTL=116 Attempts Increase MaxUserPort and TcpNumConnection Restart the server Increase IIS Max Instances and Instance MaxRequests Server Resource Only 10%-15% of the network connection is used Only 10%-15% of the CPU is used Only 25% of the memory is used

    Read the article

  • Anatomy of a .NET Assembly - CLR metadata 2

    - by Simon Cooper
    Before we look any further at the CLR metadata, we need a quick diversion to understand how the metadata is actually stored. Encoding table information As an example, we'll have a look at a row in the TypeDef table. According to the spec, each TypeDef consists of the following: Flags specifying various properties of the class, including visibility. The name of the type. The namespace of the type. What type this type extends. The field list of this type. The method list of this type. How is all this data actually represented? Offset & RID encoding Most assemblies don't need to use a 4 byte value to specify heap offsets and RIDs everywhere, however we can't hard-code every offset and RID to be 2 bytes long as there could conceivably be more than 65535 items in a heap or more than 65535 fields or types defined in an assembly. So heap offsets and RIDs are only represented in the full 4 bytes if it is required; in the header information at the top of the #~ stream are 3 bits indicating if the #Strings, #GUID, or #Blob heaps use 2 or 4 bytes (the #US stream is not accessed from metadata), and the rowcount of each table. If the rowcount for a particular table is greater than 65535 then all RIDs referencing that table throughout the metadata use 4 bytes, else only 2 bytes are used. Coded tokens Not every field in a table row references a single predefined table. For example, in the TypeDef extends field, a type can extend another TypeDef (a type in the same assembly), a TypeRef (a type in a different assembly), or a TypeSpec (an instantiation of a generic type). A token would have to be used to let us specify the table along with the RID. Tokens are always 4 bytes long; again, this is rather wasteful of space. Cutting the RID down to 2 bytes would make each token 3 bytes long, which isn't really an optimum size for computers to read from memory or disk. However, every use of a token in the metadata tables can only point to a limited subset of the metadata tables. For the extends field, we only need to be able to specify one of 3 tables, which we can do using 2 bits: 0x0: TypeDef 0x1: TypeRef 0x2: TypeSpec We could therefore compress the 4-byte token that would otherwise be needed into a coded token of type TypeDefOrRef. For each type of coded token, the least significant bits encode the table the token points to, and the rest of the bits encode the RID within that table. We can work out whether each type of coded token needs 2 or 4 bytes to represent it by working out whether the maximum RID of every table that the coded token type can point to will fit in the space available. The space available for the RID depends on the type of coded token; a TypeOrMethodDef coded token only needs 1 bit to specify the table, leaving 15 bits available for the RID before a 4-byte representation is needed, whereas a HasCustomAttribute coded token can point to one of 18 different tables, and so needs 5 bits to specify the table, only leaving 11 bits for the RID before 4 bytes are needed to represent that coded token type. For example, a 2-byte TypeDefOrRef coded token with the value 0x0321 has the following bit pattern: 0 3 2 1 0000 0011 0010 0001 The first two bits specify the table - TypeRef; the other bits specify the RID. Because we've used the first two bits, we've got to shift everything along two bits: 000000 1100 1000 This gives us a RID of 0xc8. If any one of the TypeDef, TypeRef or TypeSpec tables had more than 16383 rows (2^14 - 1), then 4 bytes would need to be used to represent all TypeDefOrRef coded tokens throughout the metadata tables. Lists The third representation we need to consider is 1-to-many references; each TypeDef refers to a list of FieldDef and MethodDef belonging to that type. If we were to specify every FieldDef and MethodDef individually then each TypeDef would be very large and a variable size, which isn't ideal. There is a way of specifying a list of references without explicitly specifying every item; if we order the MethodDef and FieldDef tables by the owning type, then the field list and method list in a TypeDef only have to be a single RID pointing at the first FieldDef or MethodDef belonging to that type; the end of the list can be inferred by the field list and method list RIDs of the next row in the TypeDef table. Going back to the TypeDef If we have a look back at the definition of a TypeDef, we end up with the following reprensentation for each row: Flags - always 4 bytes Name - a #Strings heap offset. Namespace - a #Strings heap offset. Extends - a TypeDefOrRef coded token. FieldList - a single RID to the FieldDef table. MethodList - a single RID to the MethodDef table. So, depending on the number of entries in the heaps and tables within the assembly, the rows in the TypeDef table can be as small as 14 bytes, or as large as 24 bytes. Now we've had a look at how information is encoded within the metadata tables, in the next post we can see how they are arranged on disk.

    Read the article

  • I am unable to connect to my netbook from any machine on my network until the netbook has pinged it

    - by Samuel Husky
    I have a rather strange issue with my netbook on my local network. When trying to connect to it in any way from a remote system it does not appear to find it. However if I get the netbook to ping the machine trying to connect it mystically appears to work. Below is the ping test from my main PC to the netbook. C:\Users\Sam>ping 192.168.8.102 Pinging 192.168.8.102 with 32 bytes of data: Reply from 192.168.8.100: Destination host unreachable. Reply from 192.168.8.100: Destination host unreachable. Reply from 192.168.8.100: Destination host unreachable. Reply from 192.168.8.100: Destination host unreachable. Ping statistics for 192.168.8.102: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Now a ping from the netbook to my main PC sam@malamute ~ $ ping 192.168.8.100 PING 192.168.8.100 (192.168.8.100) 56(84) bytes of data. 64 bytes from 192.168.8.100: icmp_req=1 ttl=128 time=2.46 ms 64 bytes from 192.168.8.100: icmp_req=2 ttl=128 time=0.835 ms 64 bytes from 192.168.8.100: icmp_req=3 ttl=128 time=1.60 ms 64 bytes from 192.168.8.100: icmp_req=4 ttl=128 time=1.32 ms 64 bytes from 192.168.8.100: icmp_req=5 ttl=128 time=1.34 ms ^C --- 192.168.8.100 ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4004ms rtt min/avg/max/mdev = 0.835/1.514/2.460/0.536 ms And the same ping again from the main PC after the netbook has made a connection to it C:\Users\Sam>ping 192.168.8.102 Pinging 192.168.8.102 with 32 bytes of data: Reply from 192.168.8.102: bytes=32 time=1ms TTL=64 Reply from 192.168.8.102: bytes=32 time=1ms TTL=64 Reply from 192.168.8.102: bytes=32 time=1ms TTL=64 Reply from 192.168.8.102: bytes=32 time=1ms TTL=64 Ping statistics for 192.168.8.102: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 1ms, Maximum = 1ms, Average = 1ms The netbook is running Gentoo and is currently connected via wireless. My main PC is running Windows 7 however I get the same result no matter what PC I use on this network. Please see this example from a CentOS machine on the same network [root@tiger ~]# ping 192.168.8.102 PING 192.168.8.102 (192.168.8.102) 56(84) bytes of data. From 192.168.8.200 icmp_seq=2 Destination Host Unreachable From 192.168.8.200 icmp_seq=3 Destination Host Unreachable From 192.168.8.200 icmp_seq=4 Destination Host Unreachable --- 192.168.8.102 ping statistics --- 6 packets transmitted, 0 received, +3 errors, 100% packet loss, time 5000ms , pipe 3 If you need any more information or require logs or config files please let me know and any assistance is greatly appreciated. Additional info: No responses on TCP dump from the netbook. Same result when booting into Ubuntu from a USB key. No issue when using a wired Ethernet connection.

    Read the article

  • Automount of external hard disk

    - by moose
    I have an Intenso 6002560 1TB Memory Station - an external hard disk. This hard disk gets connected via Y-USB cable. When I connect both USB-ends to my Notebook, it gets recognized by my Ubuntu 10.04.4 LTS system: moose@pc07:~$ lsusb [...] Bus 002 Device 005: ID 13fd:1840 Initio Corporation [...] and Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00065e10 Device Boot Start End Blocks Id System /dev/sda1 * 1 37810 303704064 83 Linux /dev/sda2 37810 38914 8864769 5 Extended /dev/sda5 37810 38914 8864768 82 Linux swap / Solaris Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0d6ea32a Device Boot Start End Blocks Id System /dev/sdc1 1 121601 976759008+ c W95 FAT32 (LBA) But it did not get mounted: moose@pc07:/dev$ mount -l /dev/sda1 on / type ext4 (rw,errors=remount-ro,user_xattr) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/moose/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=moose) However, I could mount it manually with mount -t vfat /dev/sdc1 /mnt/sdc1 as you can see here: moose@pc07:~$ mount -l /dev/sda1 on / type ext4 (rw,errors=remount-ro,user_xattr) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/moose/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=moose) /dev/sdc1 on /mnt/sdc1 type vfat (rw) edit: Another command: moose@pc07:~$ sudo blkid -o list device fs_type label mount point UUID ---------------------------------------------------------------------------------------------------------------------- /dev/sda1 ext4 / 45eb611b-517e-425b-8057-0391726cccd5 /dev/sda5 swap <swap> e9dc42f3-594c-4b62-874a-305eda5eed41 moose@pc07:~$ blkid -o list device fs_type label mount point UUID ---------------------------------------------------------------------------------------------------------------------- /dev/sda1 ext4 / 45eb611b-517e-425b-8057-0391726cccd5 /dev/sda5 swap <swap> e9dc42f3-594c-4b62-874a-305eda5eed41 /dev/sdc1 /mnt/sdc1 edit: another command: moose@pc07:~$ ls -l /dev/disk/by-uuid/ total 0 lrwxrwxrwx 1 root root 10 2012-09-30 09:31 45eb611b-517e-425b-8057-0391726cccd5 -> ../../sda1 lrwxrwxrwx 1 root root 10 2012-09-30 09:31 e9dc42f3-594c-4b62-874a-305eda5eed41 -> ../../sda5 Here is a link to a Launchpad question about this problem. But I would like it to mount automatically. What do I have to do?

    Read the article

  • Grub Rescue Unknown Filesystem Error. Grub Corrupted or Filesystem?

    - by nightcrawler
    Now it has happened twice & have been pulling my hairs now... I have installed xubuntu on my external hardisk & have been using it for about 3 months. It has three partitions, one of 500 mb mounted at /boot, 2nd one of 48gb mounted at / & the rest (out of 160gb) is ntfs partition....used as normal external storage. The last storage supposedly acts as a buffer b/w Linux distributions & Win platform, buffer in the sense that it provides a universal channel for data transfers. I have constantly used this external hardisk for data transfers b/w win7 laptop & xubuntu (on this external hd) without any hassle. However, on of my desktops where I have ubuntu I (for the first time) attached this external drive which let me do data transfers where all three partitions properly mounted....but then nasty thing occurred the same that occurred before. I (as usual) tried booting via this external hd (one having xubuntu, one having being formerly used under Ubuntu) I got error Now I am totally devastated because similar thing happened ~6months before when I had fedora 17 in my external hd (instead of xubuntu) & after it was used under ubuntu the same happened...i didn't reported it because I already had planned towards debian instead of rpm! The mystery is that as long as I don't attach this external hd under ubuntu the data never** corrupts whereas under win xp/7 I can use it as a normal usb storage of coarse linux partitions aren’t available under win platforms... **From corrupts I mean hd fails to boot with the error mentioned however cant say whether data within remains untouched? It seems that my grub & or MBR is corrupted. Please sir guide me to solve this issue also why I cant attach & use linux external hds under linux platform Disk /dev/sdc: 160.0 GB, 160041884672 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581806 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004e7d0 Device Boot Start End Blocks Id System /dev/sdc1 * 2048 976895 487424 83 Linux /dev/sdc2 978942 96874495 47947777 5 Extended /dev/sdc3 96874496 312575999 107850752 7 HPFS/NTFS/exFAT /dev/sdc5 978944 94726143 46873600 83 Linux /dev/sdc6 94728192 96874495 1073152 82 Linux swap / Solaris I can recall for sure that have seen a thread here when a similar problem occurred & in response someone gave solution of how to mount (now invisible) partitions & recover important data in them. I have misplaced that URL so if any can guide me thither because my important documents resides in / partition What I already have done: Without success I have tried this & related solutions What I plan to do: I believe that filesystem has corrupted & would you recommend solution like this provided I cant recall whether my /boot (500mb) partition was ext4 or ext2 though I am sure that my / (48gb) partition was ext4 UPDATE 1 Attached my external hd under Ubuntu ran followinf command as root grub-install /dev/sdc where /dev/sdc was my external hd containing corrupted xubuntu....it reported all done! I re-ran fdisk -l but to my disappointment it reported Disk /dev/sdc: 160.0 GB, 160041884672 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581806 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1b6b9167 Disk /dev/sdc doesn't contain a valid partition table ...& now I can't even access its ntfs partition (former /dev/sdc3) please help? UPDATE 2 TestDisk (by cgsecurity) failed at founding any partition table :( TestDisk 6.13, Data Recovery Utility, November 2011 Christophe GRENIER <[email protected]> http://www.cgsecurity.org Disk /dev/sdc - 160 GB / 149 GiB - CHS 19457 255 63 Partition Start End Size in sectors

    Read the article

  • Grub2 : Windows 7 can't boot installing with Ubuntu 10.04 on different hard drive

    - by dellphi
    I use a dual boot with two hard disks and two OS is Ubuntu 10.04 and Windows 7. Windows 7 installed on the first disk, first partition. Grub is installed on a second hard disk MBR, and Ubuntu installed on an extended partition on a second hard drive. When I select Windows 7 on the Grub menu, the HDD lamp lights up briefly and then black screen on the monitor, with the status of the keyboard is still functioning. Until now (with the default boot from first HDD), I have to press F12 to get into the Grub to run Linux on a second HDD. ================ fdisk -l ================================ dellph1@dellph1-desktop:~$ fdisk -l omitting empty partition (5) Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00087dec Device Boot Start End Blocks Id System /dev/sda1 * 1 23104 185582848+ 7 HPFS/NTFS /dev/sda2 23105 121601 791177122 5 Extended /dev/sda5 36107 74408 307660783+ 7 HPFS/NTFS /dev/sda6 74409 100081 206218341 7 HPFS/NTFS /dev/sda7 100082 121601 172859368+ 7 HPFS/NTFS Disk /dev/sdb: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x6d43dfb2 Device Boot Start End Blocks Id System /dev/sdb1 1 10030 80560066 5 Extended /dev/sdb5 * 1 5560 44657601 83 Linux /dev/sdb6 5560 9387 30736384 83 Linux /dev/sdb7 9387 10030 5164032 82 Linux swap / Solaris dellph1@dellph1-desktop:~$ ================= grub.cfg ================== # DO NOT EDIT THIS FILE # It is automatically generated by /usr/sbin/grub-mkconfig using templates from /etc/grub.d and settings from /etc/default/grub # BEGIN /etc/grub.d/00_header if [ -s $prefix/grubenv ]; then load_env fi set default="0" if [ ${prev_saved_entry} ]; then set saved_entry=${prev_saved_entry} save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z ${boot_once} ]; then saved_entry=${chosen} save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n ${have_grubenv} ]; then if [ -z ${boot_once} ]; then save_env recordfail; fi; fi } insmod ext2 set root='(hd1,5)' search --no-floppy --fs-uuid --set 2f014a3a-35f3-4d05-87aa-34ca677160b7 if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=1024x768 insmod gfxterm insmod vbe if terminal_output gfxterm ; then true ; else # For backward compatibility with versions of terminal.mod that don't # understand terminal_output terminal gfxterm fi fi insmod ext2 set root='(hd1,5)' search --no-floppy --fs-uuid --set 2f014a3a-35f3-4d05-87aa-34ca677160b7 set locale_dir=($root)/boot/grub/locale set lang=en insmod gettext if [ ${recordfail} = 1 ]; then set timeout=-1 else set timeout=5 fi END /etc/grub.d/00_header BEGIN /etc/grub.d/05_debian_theme insmod ext2 set root='(hd1,5)' search --no-floppy --fs-uuid --set 2f014a3a-35f3-4d05-87aa-34ca677160b7 insmod jpeg if background_image /usr/share/backgrounds/CurlsbyCandy.jpg ; then set color_normal=white/black set color_highlight=black/light-gray else set menu_color_normal=white/black set menu_color_highlight=black/light-gray fi END /etc/grub.d/05_debian_theme BEGIN /etc/grub.d/10_linux menuentry 'Ubuntu, with Linux 2.6.32-24-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd1,5)' search --no-floppy --fs-uuid --set 2f014a3a-35f3-4d05-87aa-34ca677160b7 linux /boot/vmlinuz-2.6.32-24-generic root=UUID=2f014a3a-35f3-4d05-87aa-34ca677160b7 ro splash vga=795 quiet splash nomodeset video=uvesafb:mode_option=1280x1024-24,mtrr=3,scroll=ywrap initrd /boot/initrd.img-2.6.32-24-generic } menuentry 'Ubuntu, with Linux 2.6.32-24-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd1,5)' search --no-floppy --fs-uuid --set 2f014a3a-35f3-4d05-87aa-34ca677160b7 echo 'Loading Linux 2.6.32-24-generic ...' linux /boot/vmlinuz-2.6.32-24-generic root=UUID=2f014a3a-35f3-4d05-87aa-34ca677160b7 ro single splash vga=795 echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.32-24-generic } END /etc/grub.d/10_linux BEGIN /etc/grub.d/30_os-prober menuentry "Windows 7 (loader) (on /dev/sda1)" { insmod ntfs set root='(hd0,1)' search --no-floppy --fs-uuid --set 5cac2139ac210f58 chainloader +1 } END /etc/grub.d/30_os-prober BEGIN /etc/grub.d/40_multisystem Ajout de MultiSystem MULTISYSTEM MENU menuentry "PLoP Boot Manager" { linux16 /boot/plpbt } menuentry "Smart Boot Manager" { search --set -f /boot/sbootmgr.dsk linux16 /boot/memdisk initrd16 /boot/sbootmgr.dsk } FIN MULTISYSTEM MENU END /etc/grub.d/40_multisystem ================================================ I want to keep the Grub on the second HDD. I have been using the Startup Manager, Boot Manager and Grub Customizer, and this problem still unsolved. The easiest thing that I can possibly do is to install Grub on first HDD, but I was curious and maybe someone can help.

    Read the article

  • installer can't find partition, but fdisk can find them

    - by pxd
    I'm installing ubuntu 12.04, my system had install 2 system -- winxp and ubuntu 10.10. Now, I want to update ubuntu to 12.04. I use usb disk to install 12.04. But, the installer can't not find my partition in my harddisk. But, the fdisk can find them. Can you help me? How to do? ubuntu@ubuntu:~$ sudo lshw -short H/W path Device Class Description system HP 2230s (NN868PA#AB2) /0 bus 3037 /0/9 memory 64KiB BIOS /0/0 processor Intel(R) Core(TM)2 Duo CPU T6570 @ 2.10GHz /0/0/1 memory 2MiB L2 cache /0/0/3 memory 32KiB L1 cache /0/0/0.1 processor Logical CPU /0/0/0.2 processor Logical CPU /0/2 memory 32KiB L1 cache /0/4 memory 2GiB System Memory /0/4/0 memory SODIMM [empty] /0/4/1 memory 2GiB SODIMM DDR2 Synchronous 800 MHz (1.2 ns) /0/100 bridge Mobile 4 Series Chipset Memory Controller Hub /0/100/2 display Mobile 4 Series Chipset Integrated Graphics Controller /0/100/2.1 display Mobile 4 Series Chipset Integrated Graphics Controller /0/100/1a bus 82801I (ICH9 Family) USB UHCI Controller #4 /0/100/1a.1 bus 82801I (ICH9 Family) USB UHCI Controller #5 /0/100/1a.2 bus 82801I (ICH9 Family) USB UHCI Controller #6 /0/100/1a.7 bus 82801I (ICH9 Family) USB2 EHCI Controller #2 /0/100/1b multimedia 82801I (ICH9 Family) HD Audio Controller /0/100/1c bridge 82801I (ICH9 Family) PCI Express Port 1 /0/100/1c.1 bridge 82801I (ICH9 Family) PCI Express Port 2 /0/100/1c.1/0 wlan1 network PRO/Wireless 5100 AGN [Shiloh] Network Connection /0/100/1c.2 bridge 82801I (ICH9 Family) PCI Express Port 3 /0/100/1c.4 bridge 82801I (ICH9 Family) PCI Express Port 5 /0/100/1c.5 bridge 82801I (ICH9 Family) PCI Express Port 6 /0/100/1c.5/0 eth1 network 88E8072 PCI-E Gigabit Ethernet Controller /0/100/1d bus 82801I (ICH9 Family) USB UHCI Controller #1 /0/100/1d.1 bus 82801I (ICH9 Family) USB UHCI Controller #2 /0/100/1d.2 bus 82801I (ICH9 Family) USB UHCI Controller #3 /0/100/1d.7 bus 82801I (ICH9 Family) USB2 EHCI Controller #1 /0/100/1e bridge 82801 Mobile PCI Bridge /0/100/1f bridge ICH9M LPC Interface Controller /0/100/1f.2 scsi0 storage 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] /0/100/1f.2/0 /dev/sda disk 500GB WDC WD5000BEVT-0 /0/100/1f.2/0/1 /dev/sda1 volume 48GiB Windows NTFS volume /0/100/1f.2/0/2 /dev/sda2 volume 416GiB Extended partition /0/100/1f.2/0/2/5 /dev/sda5 volume 97GiB HPFS/NTFS partition /0/100/1f.2/0/2/6 /dev/sda6 volume 198GiB HPFS/NTFS partition /0/100/1f.2/0/2/7 /dev/sda7 volume 27GiB Linux filesystem partition /0/100/1f.2/0/2/8 /dev/sda8 volume 93GiB Linux filesystem partition /0/100/1f.2/1 /dev/cdrom disk CDDVDW TS-L633M /0/1 scsi6 storage /0/1/0.0.0 /dev/sdb disk 15GB STORAGE DEVICE /0/1/0.0.0/0 /dev/sdb disk 15GB /0/1/0.0.0/0/1 /dev/sdb1 volume 14GiB Windows FAT volume /1 power HZ04037 ubuntu@ubuntu:~$ ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x31263125 Device Boot Start End Blocks Id System /dev/sda1 * 63 102277727 51138832+ 7 HPFS/NTFS/exFAT /dev/sda2 102277728 976784129 437253201 f W95 Ext'd (LBA) /dev/sda5 102277791 307078127 102400168+ 7 HPFS/NTFS/exFAT /dev/sda6 307078191 724141151 208531480+ 7 HPFS/NTFS/exFAT /dev/sda7 724142080 781459455 28658688 83 Linux /dev/sda8 781461504 976771071 97654784 83 Linux Disk /dev/sdb: 15.9 GB, 15931539456 bytes 64 heads, 32 sectors/track, 15193 cylinders, total 31116288 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009eb92 Device Boot Start End Blocks Id Systemfile:///home/ubuntu/Pictures/Screenshot%20from%202012-07-07%2010:25:40.png /dev/sdb1 * 32 31115263 15557616 c W95 FAT32 (LBA) ubuntu 12.04 installer can't find the partition in my hard disk, only find device - /dev/sda.(sorry, I'm new user, so can't send image.)

    Read the article

  • Ubuntu Server Cannot Route to the Internet

    - by ejes
    I've been having this problem for weeks now, and I can't seem to figure out the problem. My server can route the local network and serves it well, however it cannot access the internet. It can't be the router because everything else on this lan can route through the router. I've even switched the ethernet port. Any help would be appreciated. I've tried all the usual places, anyway, here are the configs: root@uhs:~# uname -a Linux uhs 3.0.0-16-generic-pae #28-Ubuntu SMP Fri Jan 27 19:24:01 UTC 2012 i686 i686 i386 GNU/Linux root@uhs:~# cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface # auto eth1 # iface eth1 inet dhcp auto eth0 iface eth0 inet static address 192.168.0.3 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 root@uhs:~# ping -c 4 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_req=1 ttl=64 time=0.334 ms 64 bytes from 192.168.0.1: icmp_req=2 ttl=64 time=0.339 ms 64 bytes from 192.168.0.1: icmp_req=3 ttl=64 time=0.324 ms 64 bytes from 192.168.0.1: icmp_req=4 ttl=64 time=0.339 ms --- 192.168.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.324/0.334/0.339/0.006 ms root@uhs:~# ping -c 4 209.85.145.103 PING 209.85.145.103 (209.85.145.103) 56(84) bytes of data. --- 209.85.145.103 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3023ms root@uhs:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:0c:6e:a0:92:6e inet addr:192.168.0.3 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:6eff:fea0:926e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13131114 errors:0 dropped:0 overruns:0 frame:0 TX packets:10540297 errors:0 dropped:0 overruns:5 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3077922794 (3.0 GB) TX bytes:3827489734 (3.8 GB) Interrupt:10 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7721 errors:0 dropped:0 overruns:0 frame:0 TX packets:7721 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:551950 (551.9 KB) TX bytes:551950 (551.9 KB) root@uhs:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 root@uhs:~# # PRETEND Traceroute root@uhs:~# for i in {1..30}; do ping -t $i -c 1 209.85.145.103; done | grep "Time to live exceeded" root@uhs:~#

    Read the article

  • How to open first n bytes of file in hexadecimal and edit it?

    - by Larssend
    I want to edit some .avi videos (cut them, to be precise) in VirtualDub but it failed to open the files. They are encoded in xvid, which I have installed, and play in KMPlayer without problem. Also, all other xvid videos can be opened and cut just fine by VirtualDub. I suspect there's something wrong in the first few bytes of these particular videos (the magic number?). This means I have to open the offending files in a hex editor and make some necessary adjustments to the header. Problem is, they are very large ( 3 GB each) and take very long time to open in UltraEdit. Can UltraEdit open just the first few bytes of a file? If not, do you know of an application that can do that? Edit: I'm using Windows XP.

    Read the article

  • How to determine the size (in bytes) of a file downloading using NSURLConnection?

    - by RexOnRoids
    I need to know the size of the file I am downloading (in bytes) into my app using NSURLConnection (GET). Here is my bytes recieved code below if it helps. What I need to know is how to get the filesize in bytes so that I can use it to show a UIProgressView. - (void)connection:(NSURLConnection *)theConnection didReceiveData:(NSData *)data // A delegate method called by the NSURLConnection as data arrives. We just // write the data to the file. { #pragma unused(theConnection) NSInteger dataLength; const uint8_t * dataBytes; NSInteger bytesWritten; NSInteger bytesWrittenSoFar; assert(theConnection == self.connection); dataLength = [data length]; dataBytes = [data bytes]; bytesWrittenSoFar = 0; do { bytesWritten = [self.fileStream write:&dataBytes[bytesWrittenSoFar] maxLength:dataLength - bytesWrittenSoFar]; assert(bytesWritten != 0); if (bytesWritten == -1) { [self _stopReceiveWithStatus:@"File write error"]; break; } else { bytesWrittenSoFar += bytesWritten; } while (bytesWrittenSoFar != dataLength); }

    Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >