Search Results

Search found 426 results on 18 pages for 'scsi'.

Page 14/18 | < Previous Page | 10 11 12 13 14 15 16 17 18  | Next Page >

• e2fsck extremely slow, although enough memory exists

  - by kaefert

  I've got this external USB-Disk: kaefert@blechmobil:~$ lsusb -s 2:3 Bus 002 Device 003: ID 0bc2:3320 Seagate RSS LLC As can be seen in this dmesg output, there is some problem that prevents that disk from beeing mounted: kaefert@blechmobil:~$ dmesg ... [ 113.084079] usb 2-1: new high-speed USB device number 3 using ehci_hcd [ 113.217783] usb 2-1: New USB device found, idVendor=0bc2, idProduct=3320 [ 113.217787] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1 [ 113.217790] usb 2-1: Product: Expansion Desk [ 113.217792] usb 2-1: Manufacturer: Seagate [ 113.217794] usb 2-1: SerialNumber: NA4J4N6K [ 113.435404] usbcore: registered new interface driver uas [ 113.455315] Initializing USB Mass Storage driver... [ 113.468051] scsi5 : usb-storage 2-1:1.0 [ 113.468180] usbcore: registered new interface driver usb-storage [ 113.468182] USB Mass Storage support registered. [ 114.473105] scsi 5:0:0:0: Direct-Access Seagate Expansion Desk 070B PQ: 0 ANSI: 6 [ 114.474342] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.475089] sd 5:0:0:0: [sdb] Write Protect is off [ 114.475092] sd 5:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 114.475959] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 114.477093] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.501649] sdb: sdb1 [ 114.502717] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.504354] sd 5:0:0:0: [sdb] Attached SCSI disk [ 116.804408] EXT4-fs (sdb1): ext4_check_descriptors: Checksum for group 3976 failed (47397!=61519) [ 116.804413] EXT4-fs (sdb1): group descriptors corrupted! ... So I went and fired up my favorite partition manager - gparted, and told it to verify and repair the partition sdb1. This made gparted call e2fsck (version 1.42.4 (12-Jun-2012)) e2fsck -f -y -v /dev/sdb1 Although gparted called e2fsck with the "-v" option, sadly it doesn't show me the output of my e2fsck process (bugreport https://bugzilla.gnome.org/show_bug.cgi?id=467925 ) I started this whole thing on Sunday (2012-11-04_2200) evening, so about 48 hours ago, this is what htop says about it now (2012-11-06-1900): PID USER PRI NI VIRT RES SHR S CPU% MEM% TIME+ Command 3704 root 39 19 1560M 1166M 768 R 98.0 19.5 42h56:43 e2fsck -f -y -v /dev/sdb1 Now I found a few posts on the internet that discuss e2fsck running slow, for example: http://gparted-forum.surf4.info/viewtopic.php?id=13613 where they write that its a good idea to see if the disk is just that slow because maybe its damaged, and I think these outputs tell me that this is not the case in my case: kaefert@blechmobil:~$ sudo hdparm -tT /dev/sdb /dev/sdb: Timing cached reads: 3562 MB in 2.00 seconds = 1783.29 MB/sec Timing buffered disk reads: 82 MB in 3.01 seconds = 27.26 MB/sec kaefert@blechmobil:~$ sudo hdparm /dev/sdb /dev/sdb: multcount = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 364801/255/63, sectors = 5860533160, start = 0 However, although I can read quickly from that disk, this disk speed doesn't seem to be used by e2fsck, considering tools like gkrellm or iotop or this: kaefert@blechmobil:~$ iostat -x Linux 3.2.0-2-amd64 (blechmobil) 2012-11-06 _x86_64_ (2 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 14,24 47,81 14,63 0,95 0,00 22,37 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util sda 0,59 8,29 2,42 5,14 43,17 160,17 53,75 0,30 39,80 8,72 54,42 3,95 2,99 sdb 137,54 5,48 9,23 0,20 587,07 22,73 129,35 0,07 7,70 7,51 16,18 2,17 2,04 Now I researched a little bit on how to find out what e2fsck is doing with all that processor time, and I found the tool strace, which gives me this: kaefert@blechmobil:~$ sudo strace -p3704 lseek(4, 41026998272, SEEK_SET) = 41026998272 write(4, "\212\354K[_\361\3nl\212\245\352\255jR\303\354\312Yv\334p\253r\217\265\3567\325\257\3766"..., 4096) = 4096 lseek(4, 48404766720, SEEK_SET) = 48404766720 read(4, "\7t\260\366\346\337\304\210\33\267j\35\377'\31f\372\252\ffU\317.y\211\360\36\240c\30`\34"..., 4096) = 4096 lseek(4, 41027002368, SEEK_SET) = 41027002368 write(4, "\232]7Ws\321\352\t\1@[+5\263\334\276{\343zZx\352\21\316`1\271[\202\350R`"..., 4096) = 4096 lseek(4, 48404770816, SEEK_SET) = 48404770816 read(4, "\17\362r\230\327\25\346//\210H\v\311\3237\323K\304\306\361a\223\311\324\272?\213\tq \370\24"..., 4096) = 4096 lseek(4, 41027006464, SEEK_SET) = 41027006464 write(4, "\367yy>x\216?=\324Z\305\351\376&\25\244\210\271\22\306}\276\237\370(\214\205G\262\360\257#"..., 4096) = 4096 lseek(4, 48404774912, SEEK_SET) = 48404774912 read(4, "\365\25\0\21|T\0\21}3t_\272\373\222k\r\177\303\1\201\261\221$\261B\232\3142\21U\316"..., 4096) = 4096 ^CProcess 3704 detached around 16 of these lines every second, so 4 read and 4 write operations every second, which I don't consider to be a lot.. And finally, my question: Will this process ever finish? If those numbers from fseek (48404774912) represent bytes, that would be something like 45 gigabytes, with this beeing a 3 terrabyte disk, which would give me 134 days to go, if the speed stays constant, and e2fsck scans the disk like this completly and only once. Do you have some advice for me? I have most of the data on that disk elsewhere, but I've put a lot of hours into sorting and merging it to this disk, so I would prefer to getting this disk up and running again, without formatting it anew. I don't think that the hardware is damaged since the disk is only a few months and since I can't see any I/O errors in the dmesg output. UPDATE: I just looked at the strace output again (2012-11-06_2300), now it looks like this: lseek(4, 1419860611072, SEEK_SET) = 1419860611072 read(4, "3#\f\2447\335\0\22A\355\374\276j\204'\207|\217V|\23\245[\7VP\251\242\276\207\317:"..., 4096) = 4096 lseek(4, 43018145792, SEEK_SET) = 43018145792 write(4, "]\206\231\342Y\204-2I\362\242\344\6R\205\361\324\177\265\317C\334V\324\260\334\275t=\10F."..., 4096) = 4096 lseek(4, 1419860615168, SEEK_SET) = 1419860615168 read(4, "\262\305\314Y\367\37x\326\245\226\226\320N\333$s\34\204\311\222\7\315\236\336\300TK\337\264\236\211n"..., 4096) = 4096 lseek(4, 43018149888, SEEK_SET) = 43018149888 write(4, "\271\224m\311\224\25!I\376\16;\377\0\223H\25Yd\201Y\342\r\203\271\24eG<\202{\373V"..., 4096) = 4096 lseek(4, 1419860619264, SEEK_SET) = 1419860619264 read(4, ";d\360\177\n\346\253\210\222|\250\352T\335M\33\260\320\261\7g\222P\344H?t\240\20\2548\310"..., 4096) = 4096 lseek(4, 43018153984, SEEK_SET) = 43018153984 write(4, "\360\252j\317\310\251G\227\335{\214`\341\267\31Y\202\360\v\374\307oq\3063\217Z\223\313\36D\211"..., 4096) = 4096 So the numbers in the lseek lines before the reads, like 1419860619264 are already a lot bigger, standing for 1.29 terabytes if those numbers are bytes, so it doesn't seem to be a linear progress on a big scale, maybe there are only some areas that need work, that have big gaps in between them. UPDATE2: Okey, big disappointment, the numbers are back to very small again (2012-11-07_0720) lseek(4, 52174548992, SEEK_SET) = 52174548992 read(4, "\374\312\22\\\325\215\213\23\0357U\222\246\370v^f(\312|f\212\362\343\375\373\342\4\204mU6"..., 4096) = 4096 lseek(4, 46603526144, SEEK_SET) = 46603526144 write(4, "\370\261\223\227\23?\4\4\217\264\320_Am\246CQ\313^\203U\253\274\204\277\2564n\227\177\267\343"..., 4096) = 4096 so either e2fsck goes over the data multiple times, or it just hops back and forth multiple times. Or my assumption that those numbers are bytes is wrong. UPDATE3: Since it's mentioned here http://forums.fedoraforum.org/showthread.php?t=282125&page=2 that you can testisk while e2fsck is running, i tried that, though not with a lot of success. When asking testdisk to display the data of my partition, this is what I get: TestDisk 6.13, Data Recovery Utility, November 2011 Christophe GRENIER <[email protected]> http://www.cgsecurity.org 1 P Linux 0 4 5 45600 40 8 732566272 Can't open filesystem. Filesystem seems damaged. And this is what strace currently gives me (2012-11-07_1030) lseek(4, 212460343296, SEEK_SET) = 212460343296 read(4, "\315Mb\265v\377Gn \24\f\205EHh\2349~\330\273\203\3375\206\10\r3=W\210\372\352"..., 4096) = 4096 lseek(4, 47347830784, SEEK_SET) = 47347830784 write(4, "]\204\223\300I\357\4\26\33+\243\312G\230\250\371*m2U\t_\215\265J \252\342Pm\360D"..., 4096) = 4096 (times are in CET)

  Read the article

• [Bash] Save part of matching pattern to variable

  - by Ben

  I want to extract a substring matching a pattern and save it to a file. An example string: Apr 12 19:24:17 PC_NMG kernel: sd 11:0:0:0: [sdf] Attached SCSI removable disk I want to extract the part between the brackets, in this case []. I tried to do something like grep -e '[$subtext]' to save the text in the brackets to a variable. Of course it doesn't work, but I am looking for a way similar to this. It would be very elegant to include a variable in a regex like this. What can I do best? Thanks!

  Read the article

• Unable to boot Windows 7 after installing Ubuntu

  - by Devendra

  I have Windows 7 on my machine and then installed Ubuntu 12.04 using a live CD. I can see both Windows 7 and Ubuntu in the grub menu, but when I select Windows 7 it shows a black screen for about 2 seconds and the returns to the Grub menu. But if I select Ubuntu it's working fine. This is the contents of the boot-repair log: Boot Info Script 0.61.full + Boot-Repair extra info [Boot-Info November 20th 2012] ============================= Boot Info Summary: =============================== => Grub2 (v2.00) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks in partition 1 for (,msdos6)/boot/grub. sda1: __________________________________________________________________________ File system: ntfs Boot sector type: Grub2 (v1.99-2.00) Boot sector info: Grub2 (v2.00) is installed in the boot sector of sda1 and looks at sector 388911128 of the same hard drive for core.img. core.img is at this location and looks in partition 1 for (,msdos6)/boot/grub. No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe sda2: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sda3: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sda4: __________________________________________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sda5: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: According to the info in the boot sector, sda5 starts at sector 2048. Operating System: Boot files: sda6: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 12.10 Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/i386-pc/core.img sda7: __________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 * 206,848 146,802,687 146,595,840 7 NTFS / exFAT / HPFS /dev/sda2 147,007,488 293,623,807 146,616,320 7 NTFS / exFAT / HPFS /dev/sda3 293,623,808 332,820,613 39,196,806 7 NTFS / exFAT / HPFS /dev/sda4 332,822,526 1,465,145,343 1,132,322,818 f W95 Extended (LBA) /dev/sda5 461,342,720 1,465,145,343 1,003,802,624 7 NTFS / exFAT / HPFS /dev/sda6 332,822,528 453,171,199 120,348,672 83 Linux /dev/sda7 453,173,248 461,338,623 8,165,376 82 Linux swap / Solaris "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/sda1 F6AE2C13AE2BCB47 ntfs /dev/sda2 DC2273012272DFC6 ntfs /dev/sda3 1E76E43376E40D79 ntfs New Volume /dev/sda5 5ED60ACDD60AA57D ntfs /dev/sda6 9e70fd16-b48b-4f88-adcf-e443aef83124 ext4 /dev/sda7 52f3dd94-6be7-4a7b-a3ae-f43eb8810483 swap ================================ Mount points: ================================= Device Mount_Point Type Options /dev/sda6 / ext4 (rw,errors=remount-ro) =========================== sda6/boot/grub/grub.cfg: =========================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ x"${feature_menuentry_id}" = xy ]; then menuentry_id_option="--id" else menuentry_id_option="" fi export menuentry_id_option if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { if [ x$feature_all_video_module = xy ]; then insmod all_video else insmod efi_gop insmod efi_uga insmod ieee1275_fb insmod vbe insmod vga insmod video_bochs insmod video_cirrus fi } if [ x$feature_default_font_path = xy ] ; then font=unicode else insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi font="/usr/share/grub/unicode.pf2" fi if loadfont $font ; then set gfxmode=auto load_video insmod gfxterm set locale_dir=$prefix/locale set lang=en_IN insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=10 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="${1}" if [ "${1}" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ "${recordfail}" != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "${linux_gfx_mode}" != "text" ]; then load_video; fi menuentry 'Ubuntu' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-simple-9e70fd16-b48b-4f88-adcf-e443aef83124' { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi linux /boot/vmlinuz-3.5.0-17-generic root=UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 ro quiet splash $vt_handoff initrd /boot/initrd.img-3.5.0-17-generic } submenu 'Advanced options for Ubuntu' $menuentry_id_option 'gnulinux-advanced-9e70fd16-b48b-4f88-adcf-e443aef83124' { menuentry 'Ubuntu, with Linux 3.5.0-17-generic' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.5.0-17-generic-advanced-9e70fd16-b48b-4f88-adcf-e443aef83124' { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi echo 'Loading Linux 3.5.0-17-generic ...' linux /boot/vmlinuz-3.5.0-17-generic root=UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 ro quiet splash $vt_handoff echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.5.0-17-generic } menuentry 'Ubuntu, with Linux 3.5.0-17-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.5.0-17-generic-recovery-9e70fd16-b48b-4f88-adcf-e443aef83124' { recordfail insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi echo 'Loading Linux 3.5.0-17-generic ...' linux /boot/vmlinuz-3.5.0-17-generic root=UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.5.0-17-generic } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry 'Windows 7 (loader) (on /dev/sda1)' --class windows --class os $menuentry_id_option 'osprober-chain-F6AE2C13AE2BCB47' { insmod part_msdos insmod ntfs set root='hd0,msdos1' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 F6AE2C13AE2BCB47 else search --no-floppy --fs-uuid --set=root F6AE2C13AE2BCB47 fi chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/30_uefi-firmware ### ### END /etc/grub.d/30_uefi-firmware ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f ${config_directory}/custom.cfg ]; then source ${config_directory}/custom.cfg elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### -------------------------------------------------------------------------------- =============================== sda6/etc/fstab: ================================ -------------------------------------------------------------------------------- # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> # / was on /dev/sda6 during installation UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda7 during installation UUID=52f3dd94-6be7-4a7b-a3ae-f43eb8810483 none swap sw 0 0 -------------------------------------------------------------------------------- =================== sda6: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) 162.831275940 = 174.838751232 boot/grub/grub.cfg 1 163.036647797 = 175.059267584 boot/initrd.img-3.5.0-17-generic 1 206.871749878 = 222.126850048 boot/vmlinuz-3.5.0-17-generic 1 163.036647797 = 175.059267584 initrd.img 1 163.036647797 = 175.059267584 initrd.img.old 1 206.871749878 = 222.126850048 vmlinuz 1 =============================== StdErr Messages: =============================== cat: write error: Broken pipe cat: write error: Broken pipe ADDITIONAL INFORMATION : =================== log of boot-repair 2012-12-11__00h59 =================== boot-repair version : 3.195~ppa28~quantal boot-sav version : 3.195~ppa28~quantal glade2script version : 3.2.2~ppa45~quantal boot-sav-extra version : 3.195~ppa28~quantal boot-repair is executed in installed-session (Ubuntu 12.10, quantal, Ubuntu, x86_64) CPU op-mode(s): 32-bit, 64-bit BOOT_IMAGE=/boot/vmlinuz-3.5.0-17-generic root=UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 ro quiet splash vt.handoff=7 =================== os-prober: /dev/sda6:The OS now in use - Ubuntu 12.10 CurrentSession:linux /dev/sda1:Windows 7 (loader):Windows:chain =================== blkid: /dev/sda1: UUID="F6AE2C13AE2BCB47" TYPE="ntfs" /dev/sda2: UUID="DC2273012272DFC6" TYPE="ntfs" /dev/sda3: LABEL="New Volume" UUID="1E76E43376E40D79" TYPE="ntfs" /dev/sda5: UUID="5ED60ACDD60AA57D" TYPE="ntfs" /dev/sda6: UUID="9e70fd16-b48b-4f88-adcf-e443aef83124" TYPE="ext4" /dev/sda7: UUID="52f3dd94-6be7-4a7b-a3ae-f43eb8810483" TYPE="swap" 1 disks with OS, 2 OS : 1 Linux, 0 MacOS, 1 Windows, 0 unknown type OS. Warning: extended partition does not start at a cylinder boundary. DOS and Linux will interpret the contents differently. =================== /etc/default/grub : # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 #GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX="" # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux #GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1" =================== /etc/grub.d/ : drwxr-xr-x 2 root root 4096 Oct 17 20:29 grub.d total 72 -rwxr-xr-x 1 root root 7541 Oct 14 23:06 00_header -rwxr-xr-x 1 root root 5488 Oct 4 15:00 05_debian_theme -rwxr-xr-x 1 root root 10891 Oct 14 23:06 10_linux -rwxr-xr-x 1 root root 10258 Oct 14 23:06 20_linux_xen -rwxr-xr-x 1 root root 1688 Oct 11 19:40 20_memtest86+ -rwxr-xr-x 1 root root 10976 Oct 14 23:06 30_os-prober -rwxr-xr-x 1 root root 1426 Oct 14 23:06 30_uefi-firmware -rwxr-xr-x 1 root root 214 Oct 14 23:06 40_custom -rwxr-xr-x 1 root root 216 Oct 14 23:06 41_custom -rw-r--r-- 1 root root 483 Oct 14 23:06 README =================== UEFI/Legacy mode: This installed-session is not in EFI-mode. EFI in dmesg. Please report this message to [email protected] [ 0.000000] ACPI: UEFI 00000000bafe7000 0003E (v01 DELL QA09 00000002 PTL 00000002) [ 0.000000] ACPI: UEFI 00000000bafe6000 00042 (v01 PTL COMBUF 00000001 PTL 00000001) [ 0.000000] ACPI: UEFI 00000000bafe3000 00256 (v01 DELL QA09 00000002 PTL 00000002) SecureBoot disabled. =================== PARTITIONS & DISKS: sda6 : sda, not-sepboot, grubenv-ok grub2, grub-pc , update-grub, 64, with-boot, is-os, not--efi--part, fstab-without-boot, fstab-without-efi, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, apt-get, grub-install, with--usr, fstab-without-usr, not-sep-usr, standard, farbios, . sda1 : sda, not-sepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, is-os, not--efi--part, part-has-no-fstab, part-has-no-fstab, no-nt, haswinload, no-recov-nor-hid, bootmgr, is-winboot, nopakmgr, nogrubinstall, no---usr, part-has-no-fstab, not-sep-usr, standard, not-far, /mnt/boot-sav/sda1. sda2 : sda, not-sepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, no-os, not--efi--part, part-has-no-fstab, part-has-no-fstab, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, nopakmgr, nogrubinstall, no---usr, part-has-no-fstab, not-sep-usr, standard, farbios, /mnt/boot-sav/sda2. sda3 : sda, not-sepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, no-os, not--efi--part, part-has-no-fstab, part-has-no-fstab, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, nopakmgr, nogrubinstall, no---usr, part-has-no-fstab, not-sep-usr, standard, farbios, /mnt/boot-sav/sda3. sda5 : sda, not-sepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, no-os, not--efi--part, part-has-no-fstab, part-has-no-fstab, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, nopakmgr, nogrubinstall, no---usr, part-has-no-fstab, not-sep-usr, standard, farbios, /mnt/boot-sav/sda5. sda : not-GPT, BIOSboot-not-needed, has-no-EFIpart, not-usb, has-os, 2048 sectors * 512 bytes =================== parted -l: Model: ATA WDC WD7500BPKT-7 (scsi) Disk /dev/sda: 750GB Sector size (logical/physical): 512B/4096B Partition Table: msdos Number Start End Size Type File system Flags 1 106MB 75.2GB 75.1GB primary ntfs boot 2 75.3GB 150GB 75.1GB primary ntfs 3 150GB 170GB 20.1GB primary ntfs 4 170GB 750GB 580GB extended lba 6 170GB 232GB 61.6GB logical ext4 7 232GB 236GB 4181MB logical linux-swap(v1) 5 236GB 750GB 514GB logical ntfs =================== parted -lm: BYT; /dev/sda:750GB:scsi:512:4096:msdos:ATA WDC WD7500BPKT-7; 1:106MB:75.2GB:75.1GB:ntfs::boot; 2:75.3GB:150GB:75.1GB:ntfs::; 3:150GB:170GB:20.1GB:ntfs::; 4:170GB:750GB:580GB:::lba; 6:170GB:232GB:61.6GB:ext4::; 7:232GB:236GB:4181MB:linux-swap(v1)::; 5:236GB:750GB:514GB:ntfs::; =================== mount: /dev/sda6 on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) none on /run/user type tmpfs (rw,noexec,nosuid,nodev,size=104857600,mode=0755) gvfsd-fuse on /run/user/dev/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,user=dev) /dev/sda1 on /mnt/boot-sav/sda1 type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) /dev/sda2 on /mnt/boot-sav/sda2 type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) /dev/sda3 on /mnt/boot-sav/sda3 type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) /dev/sda5 on /mnt/boot-sav/sda5 type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) =================== ls: /sys/block/sda (filtered): alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro sda1 sda2 sda3 sda4 sda5 sda6 sda7 size slaves stat subsystem trace uevent /sys/block/sr0 (filtered): alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro size slaves stat subsystem trace uevent /dev (filtered): alarm ashmem autofs binder block bsg btrfs-control bus cdrom cdrw char console core cpu cpu_dma_latency disk dri dvd dvdrw ecryptfs fb0 fb1 fd full fuse hpet input kmsg kvm log mapper mcelog mei mem net network_latency network_throughput null oldmem port ppp psaux ptmx pts random rfkill rtc rtc0 sda sda1 sda2 sda3 sda4 sda5 sda6 sda7 sg0 sg1 shm snapshot snd sr0 stderr stdin stdout uinput urandom v4l vga_arbiter vhost-net video0 zero ls /dev/mapper: control =================== df -Th: Filesystem Type Size Used Avail Use% Mounted on /dev/sda6 ext4 57G 2.7G 51G 6% / udev devtmpfs 1.9G 12K 1.9G 1% /dev tmpfs tmpfs 770M 892K 769M 1% /run none tmpfs 5.0M 0 5.0M 0% /run/lock none tmpfs 1.9G 260K 1.9G 1% /run/shm none tmpfs 100M 44K 100M 1% /run/user /dev/sda1 fuseblk 70G 36G 35G 51% /mnt/boot-sav/sda1 /dev/sda2 fuseblk 70G 66G 4.8G 94% /mnt/boot-sav/sda2 /dev/sda3 fuseblk 19G 87M 19G 1% /mnt/boot-sav/sda3 /dev/sda5 fuseblk 479G 436G 44G 92% /mnt/boot-sav/sda5 =================== fdisk -l: Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x1dc69d0b Device Boot Start End Blocks Id System /dev/sda1 * 206848 146802687 73297920 7 HPFS/NTFS/exFAT /dev/sda2 147007488 293623807 73308160 7 HPFS/NTFS/exFAT /dev/sda3 293623808 332820613 19598403 7 HPFS/NTFS/exFAT /dev/sda4 332822526 1465145343 566161409 f W95 Ext'd (LBA) Partition 4 does not start on physical sector boundary. /dev/sda5 461342720 1465145343 501901312 7 HPFS/NTFS/exFAT /dev/sda6 332822528 453171199 60174336 83 Linux /dev/sda7 453173248 461338623 4082688 82 Linux swap / Solaris Partition table entries are not in disk order =================== Recommended repair Recommended-Repair This setting will reinstall the grub2 of sda6 into the MBR of sda. Additional repair will be performed: unhide-bootmenu-10s grub-install (GRUB) 2.00-7ubuntu11,grub-install (GRUB) 2. Reinstall the GRUB of sda6 into the MBR of sda Installation finished. No error reported. grub-install /dev/sda: exit code of grub-install /dev/sda:0 update-grub Generating grub.cfg ... Found linux image: /boot/vmlinuz-3.5.0-17-generic Found initrd image: /boot/initrd.img-3.5.0-17-generic Found memtest86+ image: /boot/memtest86+.bin Found Windows 7 (loader) on /dev/sda1 Unhide GRUB boot menu in sda6/boot/grub/grub.cfg Boot successfully repaired. You can now reboot your computer. The boot files of [The OS now in use - Ubuntu 12.10] are far from the start of the disk. Your BIOS may not detect them. You may want to retry after creating a /boot partition (EXT4, >200MB, start of the disk). This can be performed via tools such as gParted. Then select this partition via the [Separate /boot partition:] option of [Boot Repair]. (https://help.ubuntu.com/community/BootPartition)

  Read the article

• Sony VAIO with Insyde H2O EFI bios will not boot into GRUB EFI

  - by Rohan Dhruva

  I bought a new Sony Vaio S series laptop. It uses Insyde H2O BIOS EFI, and trying to install Linux on it is driving me crazy. root@kubuntu:~# parted /dev/sda print Model: ATA Hitachi HTS72756 (scsi) Disk /dev/sda: 640GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 274MB 273MB fat32 EFI system partition hidden 2 274MB 20.8GB 20.6GB ntfs Basic data partition hidden, diag 3 20.8GB 21.1GB 273MB fat32 EFI system partition boot 4 21.1GB 21.3GB 134MB Microsoft reserved partition msftres 5 21.3GB 342GB 320GB ntfs Basic data partition 6 342GB 358GB 16.1GB ext4 Basic data partition 7 358GB 374GB 16.1GB ntfs Basic data partition 8 374GB 640GB 266GB ntfs Basic data partition What is surprising is that there are 2 EFI system partitions on the disk. The sda2 partition is a 20gb recovery partition which loads windows with a basic recovery interface. This is accessible by pressing the "ASSIST" button as opposed to the normal power button. I presume that the sda1 EFI System Partition (ESP) loads into this recovery. The sda3 ESP has more fleshed out entries for Microsoft Windows, which actually goes into Windows 7 (as confirmed by bcdedit.exe on Windows). Ubuntu is installed on sda6, and while installation I chose sda3 as my boot partition. The installer correctly created a sda3/EFI/ubuntu/grubx64.efi application. The real problem: for the life of me, I can't set it to be the default! I tried creating a sda3/startup.nsh which called grubx64.efi, but it didn't help -- on rebooting, the system still boots into windows. I tried using efibootmgr, and that shows as it it worked: root@kubuntu:~# efibootmgr BootCurrent: 0000 BootOrder: 0000,0001 Boot0000* EFI USB Device Boot0001* Windows Boot Manager root@kubuntu:~# efibootmgr --create --gpt --disk /dev/sda --part 3 --write-signature --label "GRUB2" --loader "\\EFI\\ubuntu\\grubx64.efi" BootCurrent: 0000 BootOrder: 0002,0000,0001 Boot0000* EFI USB Device Boot0001* Windows Boot Manager Boot0002* GRUB2 root@kubuntu:~# efibootmgr BootCurrent: 0000 BootOrder: 0002,0000,0001 Boot0000* EFI USB Device Boot0001* Windows Boot Manager Boot0002* GRUB2 However, on rebooting, as you guessed, the machine rebooted directly back into Windows. The only things I can think of are: The sda1 partition is somehow being used Overwrite /EFI/Boot/bootx64.efi and /EFI/Microsoft/Boot/bootmgfw.efi with grubx64.efi [but this seems really radical]. Can anyone please help me out? Thanks -- any help is greatly appreciated, as this issue is driving me crazy!

  Read the article

• E160 ubuntu 12.04 can't detect the modem

  - by Matt

  i've got problem with e160 on ubuntu 12.04. I'cant configure network manager and connect because NM can't see the e160. I;ve tried lot of solutions with no result. ateusz@mateusz-Aspire-5738:~$ sudo usb_modeswitch -v 0x12d1 -p 0x1003 -H [sudo] password for mateusz: aLooking for default devices ... found matching product ID adding device Found device in default mode, class or configuration (1) Accessing device 002 on bus 001 ... Getting the current device configuration ... OK, got current device configuration (1) Using first interface: 0x00 Using endpoints 0x01 (out) and 0x82 (in) Not a storage device, skipping SCSI inquiry USB description data (for identification) ------------------------- Manufacturer: HUAWEI Technology Product: HUAWEI Mobile Serial No.: not provided ------------------------- Sending Huawei control message ... OK, Huawei control message sent - Run lsusb to note any changes. Bye. Dmesg [ 521.480062] usb 1-4: reset high-speed USB device number 4 using ehci_hcd [ 521.617792] option 1-4:1.1: GSM modem (1-port) converter detected [ 521.617945] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB0 [ 521.618062] option 1-4:1.0: GSM modem (1-port) converter detected [ 521.618232] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB1 [ 530.840276] option: option_instat_callback: error -108 [ 530.840455] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 [ 530.840484] option 1-4:1.0: device disconnected [ 537.680378] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0 [ 537.680398] option 1-4:1.1: device disconnected [ 537.792088] usb 1-4: reset high-speed USB device number 4 using ehci_hcd [ 537.929549] option 1-4:1.1: GSM modem (1-port) converter detected [ 537.929702] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB0 [ 537.929818] option 1-4:1.0: GSM modem (1-port) converter detected [ 537.929993] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB1 [ 547.224294] option: option_instat_callback: error -108 [ 547.224470] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 [ 547.224511] option 1-4:1.0: device disconnected [ 556.988066] tty_ldisc_hangup: waiting (usb-storage) for ttyUSB0 took too long, but we keep waiting... [ 558.990663] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0 [ 558.990698] option 1-4:1.1: device disconnected [ 559.100068] usb 1-4: reset high-speed USB device number 4 using ehci_hcd [ 559.241293] option 1-4:1.1: GSM modem (1-port) converter detected [ 559.241446] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB0 [ 559.241565] option 1-4:1.0: GSM modem (1-port) converter detected [ 559.241739] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB1 [ 568.728283] option: option_instat_callback: error -108 [ 568.728466] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 [ 568.728496] option 1-4:1.0: device disconnected lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 064e:a103 Suyin Corp. Acer/HP Integrated Webcam [CN0314] Bus 005 Device 002: ID 09da:c20a A4 Tech Co., Ltd Bus 001 Device 002: ID 12d1:1003 Huawei Technologies Co., Ltd. E220 HSDPA Modem / E230/E270/E870 HSDPA/HSUPA Modem

  Read the article

• Sony VAIO is booting directly into Windows without showing grub

  - by Rohan Dhruva

  I bought a new Sony Vaio S series laptop. It uses Insyde H2O BIOS EFI, and trying to install Linux on it is driving me crazy. root@kubuntu:~# parted /dev/sda print Model: ATA Hitachi HTS72756 (scsi) Disk /dev/sda: 640GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 274MB 273MB fat32 EFI system partition hidden 2 274MB 20.8GB 20.6GB ntfs Basic data partition hidden, diag 3 20.8GB 21.1GB 273MB fat32 EFI system partition boot 4 21.1GB 21.3GB 134MB Microsoft reserved partition msftres 5 21.3GB 342GB 320GB ntfs Basic data partition 6 342GB 358GB 16.1GB ext4 Basic data partition 7 358GB 374GB 16.1GB ntfs Basic data partition 8 374GB 640GB 266GB ntfs Basic data partition What is surprising is that there are 2 EFI system partitions on the disk. The sda2 partition is a 20gb recovery partition which loads windows with a basic recovery interface. This is accessible by pressing the "ASSIST" button as opposed to the normal power button. I presume that the sda1 EFI System Partition (ESP) loads into this recovery. The sda3 ESP has more fleshed out entries for Microsoft Windows, which actually goes into Windows 7 (as confirmed by bcdedit.exe on Windows). Ubuntu is installed on sda6, and while installation I chose sda3 as my boot partition. The installer correctly created a sda3/EFI/ubuntu/grubx64.efi application. The real problem: for the life of me, I can't set it to be the default! I tried creating a sda3/startup.nsh which called grubx64.efi, but it didn't help -- on rebooting, the system still boots into windows. I tried using efibootmgr, and that shows as it it worked: root@kubuntu:~# efibootmgr BootCurrent: 0000 BootOrder: 0000,0001 Boot0000* EFI USB Device Boot0001* Windows Boot Manager root@kubuntu:~# efibootmgr --create --gpt --disk /dev/sda --part 3 --write-signature --label "GRUB2" --loader "\\EFI\\ubuntu\\grubx64.efi" BootCurrent: 0000 BootOrder: 0002,0000,0001 Boot0000* EFI USB Device Boot0001* Windows Boot Manager Boot0002* GRUB2 root@kubuntu:~# efibootmgr BootCurrent: 0000 BootOrder: 0002,0000,0001 Boot0000* EFI USB Device Boot0001* Windows Boot Manager Boot0002* GRUB2 However, on rebooting, as you guessed, the machine rebooted directly back into Windows. The only things I can think of are: The sda1 partition is somehow being used Overwrite /EFI/Boot/bootx64.efi and /EFI/Microsoft/Boot/bootmgfw.efi with grubx64.efi [but this seems really radical]. Can anyone please help me out? Thanks -- any help is greatly appreciated, as this issue is driving me crazy!

  Read the article

• Apprentice Boot Camp in South Africa (Part 1)

  - by Tim Koekkoek

  By Maximilian Michel (DE), Jorge Garnacho (ES), Daniel Maull (UK), Adam Griffiths (UK), Guillermo De Las Nieves (ES), Catriona McGill (UK), Ed Dunlop (UK) The Boot Camp in South Africa was an amazing experience for all of us. The minute we landed, we were made to feel at home from our host Patrick Fitzgerald. The whole family who run the Guest House were also very friendly and always keen to help us. Since we had people from South Africa to show us all the amazing sights and their traditional ways to live their lives, the two weeks were very enjoyable for all of us and we came much closer together as a group. You can read this in the following parts of this report. Enjoy! The first group of Apprentices in Oracle (from left to right): Maximilian Michel (DE), Jorge Garnacho (ES), Daniel Maull (UK), Adam Griffiths (UK), Guillermo De Las Nieves (ES), Catriona McGill (UK), Ed Dunlop (UK) The Training Well, it’s time to talk about the main purpose of our trip to South Africa: the training. Two weeks, two courses. Servers and Storage. Two weeks to learn as much as possible and get the certificate. First week: Eben Pretorius with Servers Boot Camp. Learning about: • Machines: T1000, T2000, T3, T4, M series; • How to connect to the machines: serial and network connections; • Levels of software: ALOM, ILOM, OBP and of course the operating system, Solaris Combined with the practical part (screwdriver in one hand, and antistatic wristband on the other) makes quite a lot of stuff! But fortunately, Eben was able to tell us about everything without making our brains explode. For the second week: Storage Boot Camp with Deon Van Vuuren. Taking a look at the content: • Storage machines; • Connectors and protocols: SCSi, SAS, SATA Fiber Channel. Again, huge amounts of information, but Deon definitely did a great job and helped us learn it all. At the end, there was just one question left. Were we able to pass the exam and get the certificate? Well, what can we say? Just take a closer look at the picture above and make your conclusions! Our lovely Oracle office in Woodmead (near Johannesburg) We are all very proud to receive certification in “Server and Storage Support Fundamentals” together with our trainer Deon Van Vuuren. In summary, in case that you don't remember any of the above, the allies for a field engineer are: • System Handbook • EIS-DVD • A proper toolkit With these tools by our side, we’ll be unbeatable!  In the next article later this week, you can find part 2 of our experiences!

  Read the article

• Ubuntu 14.04 : Lost my sound randomly tried a few commands and I think I failed

  - by Marc-Antoine Théberge

  I lost my sound the other day and I tried to delete pulseaudio then reinstall, then I tried to delete it and install alsa, It did not work and I had to reinstall everything; overall bad idea... now I can't have any sound. Should I do a fresh install? I don't know how to boot an usb drive with GRUB... Here's my sysinfo System information report, generated by Sysinfo: 2014-05-28 05:45:58 http://sourceforge.net/projects/gsysinfo SYSTEM INFORMATION Running Ubuntu Linux, the Ubuntu 14.04 (trusty) release. GNOME: 3.8.4 (Ubuntu 2014-03-17) Kernel version: 3.13.0-27-generic (#50-Ubuntu SMP Thu May 15 18:08:16 UTC 2014) GCC: 4.8 (i686-linux-gnu) Xorg: 1.15.1 (16 April 2014 01:40:08PM) (16 April 2014 01:40:08PM) Hostname: mark-laptop Uptime: 0 days 11 h 43 min CPU INFORMATION GenuineIntel, Intel(R) Atom(TM) CPU N270 @ 1.60GHz Number of CPUs: 2 CPU clock currently at 1333.000 MHz with 512 KB cache Numbering: family(6) model(28) stepping(2) Bogomips: 3192.13 Flags: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx constant_tsc arch_perfmon pebs bts aperfmperf pni dtes64 monitor ds_cpl est tm2 ssse3 xtpr pdcm movbe lahf_lm dtherm MEMORY INFORMATION Total memory: 2007 MB Total swap: 1953 MB STORAGE INFORMATION SCSI device - scsi0 Vendor: ATA Model: ST9160310AS HARDWARE INFORMATION MOTHERBOARD Host bridge Intel Corporation Mobile 945GSE Express Memory Controller Hub (rev 03) Subsystem: ASUSTeK Computer Inc. Device 8340 PCI bridge(s) Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode]) ISA bridge Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) Subsystem: ASUSTeK Computer Inc. Device 830f IDE interface Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode] (rev 02) (prog-if 80 [Master]) Subsystem: ASUSTeK Computer Inc. Device 830f GRAPHIC CARD VGA controller Intel Corporation Mobile 945GSE Express Integrated Graphics Controller (rev 03) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device 8340 SOUND CARD Multimedia controller Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02) Subsystem: ASUSTeK Computer Inc. Device 831a NETWORK Ethernet controller Qualcomm Atheros AR8121/AR8113/AR8114 Gigabit or Fast Ethernet (rev b0) Subsystem: ASUSTeK Computer Inc. Device 8324

  Read the article

• What does Ubuntu do when I signal undocking to a laptop?

  - by Seppo Erviälä

  It seems that Ubuntu runs some script or command when I signal that I want to undock my laptop by pressing the undock button on the dock. Most visible thing that happens is that resolution on external display is changed. After prepearing for undock my laptop is still connected to power, VGA-output and audio jacks through dock but not to any usb devices or optical drive. I'm running 11.04 on a ThinkPad X61s with X6 UltraBase. What happens when I signal undocking? This is what dmesg says after pressing undock button: [81459.990682] ata1.00: disabled [81459.990727] ata1.00: detaching (SCSI 0:0:0:0) [81459.991722] ACPI: \_SB_.GDCK - undocking [81460.009462] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D0 [81460.020252] ehci_hcd 0000:00:1a.7: BAR 0: set to [mem 0xfe226c00-0xfe226fff] (PCI address [0xfe226c00-0xfe226fff]) [81460.020265] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D0 [81460.020281] ehci_hcd 0000:00:1a.7: restoring config space at offset 0xf (was 0x300, writing 0x30b) [81460.020309] ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102) [81460.020338] ehci_hcd 0000:00:1a.7: PME# disabled [81460.020346] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D0 [81460.020352] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D0 [81460.020363] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [81460.020372] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [81460.020432] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0 [81460.040071] ehci_hcd 0000:00:1d.7: BAR 0: set to [mem 0xfe227000-0xfe2273ff] (PCI address [0xfe227000-0xfe2273ff]) [81460.040085] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0 [81460.040104] ehci_hcd 0000:00:1d.7: restoring config space at offset 0xf (was 0x400, writing 0x40b) [81460.040133] ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102) [81460.040170] ehci_hcd 0000:00:1d.7: PME# disabled [81460.040178] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0 [81460.040184] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0 [81460.040195] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [81460.040204] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [81460.040503] ehci_hcd 0000:00:1d.7: PCI INT D disabled [81460.040552] ehci_hcd 0000:00:1d.7: PME# enabled [81460.061657] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D3 [81460.200414] usb 1-4: USB disconnect, address 14 [81462.220088] ehci_hcd 0000:00:1a.7: PCI INT C disabled [81462.220169] ehci_hcd 0000:00:1a.7: PME# enabled [81462.240115] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D3

  Read the article

• Weird Ubuntu Desktop Boot Partition On External Hard Drive

  - by Magnitus

  I have a Thinkpad with Windows 7. Last time I installed an Ubuntu/Windows dual boot, Windows was never same after and regularly got corrupted so this time, I installed Ubuntu on a separate external hard drive. I took a 500 GB external hard drive and used Windows to shrink the partition on it to 400 GB, freeing 100 GB to install Ubuntu. Then I modified the booting priority of my computer to boot from the external hard drive if present. Then, I installed Ubuntu desktop on the external hard drive using a DVD, picked the most simplistic partitioning scheme I could get away with (didn't go auto as it didn't include the external hard drive as a choice) and voilà. Fast forward some time and I'm trying to refresh my understanding of Linux partitions to install a bunch of servers, so I'm looking at the current partitioning scheme on my external hard drive and find the boot partition puzzling... sda is my integrated hard drive with Windows 7. sdb is my Ubuntu desktop external hard drive. Running parted on sdb, I get this: (parted) print Model: WD My Passport 0740 (scsi) Disk /dev/sdb: 500GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 393GB 393GB primary ntfs boot 2 393GB 500GB 107GB extended 5 393GB 425GB 32.8GB logical linux-swap(v1) 6 425GB 500GB 74.6GB logical ext4 At this point, I'm wondering why the ntfs partition is flagged as "boot" and not my ext4 partition which is the partition that contains / (and by extension, /boot since it's not on its own separate partition). Looking at mtab only confirms what I already know: eric@eric-ThinkPad-W530:~$ sudo cat /etc/mtab /dev/sdb6 / ext4 rw,errors=remount-ro 0 0 proc /proc proc rw,noexec,nosuid,nodev 0 0 sysfs /sys sysfs rw,noexec,nosuid,nodev 0 0 none /sys/fs/cgroup tmpfs rw 0 0 none /sys/fs/fuse/connections fusectl rw 0 0 none /sys/kernel/debug debugfs rw 0 0 none /sys/kernel/security securityfs rw 0 0 udev /dev devtmpfs rw,mode=0755 0 0 devpts /dev/pts devpts rw,noexec,nosuid,gid=5,mode=0620 0 0 tmpfs /run tmpfs rw,noexec,nosuid,size=10%,mode=0755 0 0 none /run/lock tmpfs rw,noexec,nosuid,nodev,size=5242880 0 0 none /run/shm tmpfs rw,nosuid,nodev 0 0 none /run/user tmpfs rw,noexec,nosuid,nodev,size=104857600,mode=0755 0 0 none /sys/fs/pstore pstore rw 0 0 systemd /sys/fs/cgroup/systemd cgroup rw,noexec,nosuid,nodev,none,name=systemd 0 0 gvfsd-fuse /run/user/1000/gvfs fuse.gvfsd-fuse rw,nosuid,nodev,user=eric 0 0 /dev/sdb1 /media/eric/My\040Passport fuseblk rw,nosuid,nodev,allow_other,default_permissions,blksize=4096 0 0 My lack of understanding concerning this is not vital to anything (this is only my development desktop partition), but somehow annoys me. Any insight that could shed some light on this would be welcome.

  Read the article

• Ubuntu 10.04 preseed unattended install results in faulty partition table

  - by joschi

  I'm currently trying to set up an unattended installation of Ubuntu 10.04 (Lucid Lynx) through preseeding. But whenever I try to create a custom partition scheme, the Debian installer (which Ubuntu is using) produces a faulty partition table. I've taken the partition scheme described in the example preseed file: d-i partman-auto/expert_recipe string \ boot-root :: \ 40 50 100 ext3 \ $primary{ } $bootable{ } \ method{ format } format{ } \ use_filesystem{ } filesystem{ ext3 } \ mountpoint{ /boot } \ . \ 500 10000 1000000000 ext3 \ method{ format } format{ } \ use_filesystem{ } filesystem{ ext3 } \ mountpoint{ / } \ . \ 64 512 300% linux-swap \ method{ swap } format{ } \ . Unfortunately it also produces an incorrect partition table on the disk. The installation process itself is working and the installed system eventually boots and is working, as far as I can tell. But fdisk and cfdisk are still complaining: # fdisk -l /dev/sda Disk /dev/sda: 17.2 GB, 17179869184 bytes 255 heads, 63 sectors/track, 2088 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000a1cdd Device Boot Start End Blocks Id System /dev/sda1 * 1 5 37888 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 5 2089 16736257 5 Extended /dev/sda5 5 2013 16121856 83 Linux /dev/sda6 2013 2089 613376 82 Linux swap / Solaris cfdisk even refuses to start at all: # cfdisk /dev/sda FATAL ERROR: Bad primary partition 1: Partition ends in the final partial cylinder parted on the other hand does not complain about the cylinder boundary of /dev/sda1: # parted /dev/sda p Model: VMware Virtual disk (scsi) Disk /dev/sda: 17.2GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 39.8MB 38.8MB primary ext4 boot 2 40.9MB 17.2GB 17.1GB extended 5 40.9MB 16.5GB 16.5GB logical ext4 6 16.6GB 17.2GB 628MB logical linux-swap(v1) Since the installed system is working, it shouldn't be a big problem but I'm afraid that this will mean trouble in the future.

  Read the article

• Debian and Multipath IO problem

  - by tearman

  Basically the situation is, I have a box running Debian, the box internally has an Intel SCSI RAID controller which is controlling 2 hard drives in RAID1 mode which is where the OS is installed. Further, I have a QLogic fiber channel adapter that connects the unit to a Fiber Channel SAN. My process of installation is I'll install Debian to the local drives, and leave the QLogic firmware out of it for the time being. Then once I get the unit online, I'll install the firmware drivers. This flops my internal drives from /dev/sda to /dev/sdc, which is a bit annoying, but recoverable. Probably should address these by UUID anyways. Once I get back online, I have to install multipath-tools (the framework is a multipath framework). However, once I reboot the machine again, it fails on boot after discovering multipath targets, saying my local drives are busy and cannot be mounted to /root. Any help in what may be the problem here? Or at least how to disable multipath until after the unit boots and then ignores the internal drives?

  Read the article

• Dell Poweredge 2600 RAID Transfer How-to

  - by DCookie

  Help, please! Hardware: Dell Poweredge 2600 PERC 4 SCSI Drives, 1 standalone 3 in a RAID 5 configuration OS: Windows 2000 Server In other words, a fairly old system. Anyway, we are in the process of taking over support for this site. The current tech wants out and is fading from view fast, so we need to solve this problem: The standalone disk (where the OS was) failed. We've replaced the disk, installed the OS, but need to know exactly how to proceed from here. I've never worked with a RAID system before, so I don't want to touch anything without knowing what I'm doing. We are not certain if the site will want us to attempt to recover the array or wait for the old tech to become available. We have replaced the server with a temporary box, and recovered MOST of the data from an online backup service. However, the other tech failed to backup a part of the data and the only copy of it is on this RAID array. Hence, our caution. We have poked minimally around in the boot-up PERC config utility, and it seems to me that that's where we'll need to be to reclaim the array. Another possibility is that there is some Dell software for the RAID controller we need to acquire. Can anyone provide clues as to how to proceed from here? Any help GREATLY appreciated.

  Read the article

• RAID 5 - DELL 2850 and others

  - by Kiara

  I have installed Ubuntu on a DELL 2850 and I have configured an array of 5 disks (SCSI 73GB 10K) in RAID5. I wanted to simulate a drive error so in the middle of something I just took one of the drives out and put it back again after a bit. Then the drive shows an orange light and seems to be rebuilding but actually is taking hours and hours with no results. So I went to the PERC utility (Ctrl+M) and the disk shows "REBLD". But it never gets to an online state. So I went to Objects - Physical drives - Rebuilding - View rebuild process. And in here I can see a bar moving from 0%... but if I reboot before finishing and get into the PERC Utility again, it seems to start again rebuilding from 0% - so it is not rebuilding automatically. My concern is: what would happen in a real situation? Do I have to just switch the server off and go to the Perc utility to start the rebuilding manually? I thought the whole point was to have this done automatically and without the need of stopping the server. Or does it perhaps rebuild automatically indeed but needs to have enough time without rebooting because otherwise the rebuilding process will start from scratch? It seems to take more than 3h for a 73gb disk! My second question is: can I mix then hard drives? So if I have a RAID of 5x73GB 10K can I use different size (146GB) or speeds (15K)? Apparently someone said it is OK in here Poweredge 2850: replace disk with larger in RAID?

  Read the article

• How can I fix my corrupted RAID1 ext4 partition on a Synology DS212 NAS?

  - by Neil

  I have two identical 3 TB disks that were in a RAID1 array, where one disk crashed. I replaced the failed disk, but not after the RAID partitions got messed up. I need to figure out how to restore the RAID array and get at my ext4 partition. Here are the properties of the surviving disk: # fdisk -l /dev/sda fdisk: device has more than 2^32 sectors, can't use all of them Disk /dev/sda: 2199.0 GB, 2199023255040 bytes 255 heads, 63 sectors/track, 267349 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 267350 2147483647+ ee EFI GPT # parted /dev/sda print Model: ATA ST3000DM001-9YN1 (scsi) Disk /dev/sda: 3001GB Sector size (logical/physical): 512B/512B Partition Table: gpt Disk Flags: Number Start End Size File system Name Flags 1 131kB 2550MB 2550MB ext4 raid 2 2550MB 4698MB 2147MB linux-swap(v1) raid 5 4840MB 3001GB 2996GB raid I replaced the failed drive, and cloned the surviving drive to it so I have something to work with. I cloned the drives with dd if=/dev/sdb of=/dev/sda conv=noerror bs=64M, and now /dev/sda and /dev/sdb are identical. Here is the RAID information: # cat /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] md1 : active raid1 sdb2[1] 2097088 blocks [2/1] [_U] md0 : active raid1 sdb1[1] 2490176 blocks [2/1] [_U] unused devices: <none> It seems that md2 is missing. Here is what testdisk 6.14-WIP finds: Disk /dev/sda - 3000 GB / 2794 GiB - CHS 364801 255 63 Current partition structure: Partition Start End Size in sectors 1 P Linux Raid 256 4980735 4980480 [md0] 2 P Linux Raid 4980736 9175039 4194304 [md1] Invalid RAID superblock 5 P Linux Raid 9453280 5860519007 5851065728 5 P Linux Raid 9453280 5860519007 5851065728 # After a quick search Disk /dev/sda - 3000 GB / 2794 GiB - CHS 364801 255 63 Partition Start End Size in sectors D MS Data 256 4980607 4980352 [1.41.12-2197] D Linux Raid 256 4980735 4980480 [md0] D Linux Swap 4980736 9174895 4194160 D Linux Raid 4980736 9175039 4194304 [md1] >P MS Data 9481056 5858437983 5848956928 [1.41.12-2228] And listing the files on the last partition in the list shows all of my files intact. What should I do?

  Read the article

• ZFS + FreeBSD + virtualbox

  - by John

  Hi, I'm configuring a FreeBSD server hosting virtualbox serving half dozen mission critical busy mail servers. I just learned ZFS, I'm quite attracted, but have a few questions: what is the CPU overhead of ZFS? I googled and found little (or no) benchmark for that. from what I learned, when ZFS updates files, it keeps the old file as snapshot, and write the updated part for the new version. However that would mean for each snapshot it keeps that require significant storage overhead. How much is this storage overhead? For example, suppose I have 2TB usable space, how much space can actually be used for the latest version of files one year later? is FreeBSD with ZFS hosting virtualbox serving half dozen busy guest mission critical mail servers a reasonable combination? Anything particular to be careful with? And can I still choose ZFS for the guest OSs? This is because I may build another identical such box for redundancy, and will need to do some mirroring between each pair of the guest systems across the boxes. I'm trying to configure a Dell R710 for this. From what I learned, I shouldn't choose any RAID at all, is that true? In that case, are the drives still arrive hot swappable? this may sounds a bit pathetic, but since I have no experience with ZFS at all, and this is a mission critical server, so just ask just in case: I'm choosing twin Intel L5630 processors, and 6 x 600GB 15K RPM Serial-Attach SCSI drives. If I need more space in the future, I would just hot swap some drivers with larger capacity to expand the storage. There is no problem with these, right?

  Read the article

• Sparc v440 unable 2 boot after recommended patch install

  - by user100660

  After installing the October 2011 recommended patch bundle on a Solaris 10 the host fails to boot. The output is {0} ok boot SC Alert: Host System has Reset screen not found. keyboard not found. Keyboard not present. Using ttya for input and output. Sun Fire V440, No Keyboard Copyright 1998-2003 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.10.10, 8192 MB memory installed, Serial #54744555. Ethernet address 0:3:ba:43:55:eb, Host ID: 834355eb. Rebooting with command: boot Boot device: /pci@1f,700000/scsi@2/disk@0,0:a File and args: \ Evaluating: Out of memory Warning: Fcode sequence resulted in a net stack depth change of 1 Evaluating: Evaluating: The file just loaded does not appear to be executable. {3} ok If I do a boot -F failsafe the host come up and I'm able to mount the root device (ufs on /dev/dsk/c1t0d0s0) and nothing appears broken, i.e I can see the logfiles from the patch install etc. Root device still have 1GB+ free. Only 2 kernel patches was installed from the patch bundle: 144500-19 & 147440-02. Any hints how to debug it further, etc.

  Read the article

• Unable to boot with Windows 2008 DVD / USB Key

  - by r0ca

  Hi everyone, I am trying to install Windows 2008 server on a HP Proliant DL180 G5. There is no built-in DVD reader so I need to use my LaCie USB one. When I put the CD in and boot from the USB DVD on the server, I get the error message: Boot Failed! Please insert boot media in selected boot device. So I tried with another Windows bootable CD and still no luck. What I've done then, I copied the installation DVD on my 16go USB key. Again, impossible to boot from the USB Key. I have 2 147go SAS 15k HDD on my server. They are not showing in the Bios. I was wondering if this is a reason why nothing will boot on it. I am trying to find a way to deploy Windows 2008 server on my HP server as soon as possible. If you guys have ideas, feel free to let me know :) Best regards, David. System Information: HP Proliant DL180 G5 Quad-Core 2.5 4GO Ram 2x 147GO SAS 15k P.S. This is my first installation ever on SAS/SCSI HDD. Thanks a bunch! Edit: Well, my bad! I purchased a new USB DVD and now I can install Windows 2008 server. Thanks a bunch for your help!

  Read the article

• Resize Debian in VirtualBox

  - by Poni

  I have a VM with one HD of size 3GB and I'd like to enlarge its HD to 7GB. So I execute this command on the host (while guest is shutdown): VBoxManage modifyhd debian.vdi --resize 7168 Then I run the guest, Debian 6, and then: smith@debian6:~$ df -h Filesystem Size Used Avail Use% Mounted on /dev/sda1 2.8G 2.6G 60M 98% / tmpfs 61M 0 61M 0% /lib/init/rw udev 57M 160K 57M 1% /dev tmpfs 61M 0 61M 0% /dev/shm smith@debian6:~$ sudo parted /dev/sda print Model: ATA VBOX HARDDISK (scsi) Disk /dev/sda: 3221MB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 3035MB 3034MB primary ext3 boot 2 3036MB 3220MB 185MB extended 5 3036MB 3220MB 185MB logical linux-swap(v1) smith@debian6:~$ cat /proc/partitions major minor #blocks name 8 0 3145728 sda 8 1 2962432 sda1 8 2 1 sda2 8 5 180224 sda5 So, no automatic resizing (detection) of the HD/partition (while VirtualBox, in the host, shows it's 7GB now). Ok... Then I do: smith@debian6:~$ sudo resize2fs /dev/sda1 resize2fs 1.41.12 (17-May-2010) The filesystem is already 740608 blocks long. Nothing to do! smith@debian6:~$ sudo parted GNU Parted 2.3 Using /dev/sda Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) select /dev/sda1 Using /dev/sda1 (parted) resize WARNING: you are attempting to use parted to operate on (resize) a file system. parted's file system manipulation code is not as robust as what you'll find in dedicated, file-system-specific packages like e2fsprogs. We recommend you use parted only to manipulate partition tables, whenever possible. Support for performing most operations on most types of file systems will be removed in an upcoming release. Partition number? 1 Start? 0 End? [3034MB]? Here I'm stuck. At the above parted it asks me to resize to 3GB. No point in that, right.. What should I do in order to enlarge this partition?

  Read the article

• Cheapest iSCSI SAN for Windows 2008/SQL Server clustering?

  - by MichaelGG

  Are there any production-quality iSCSI SANs suitable for use with Windows Server 2008/SQL Server for failover clustering? So far, I've only seen Dell's MD3000i, and HP's MSA 2000 (2012i), which both are around $6K with a minimal disk configuration. Buffalo (yea, I know), has a $1000 device with iSCSI support, but they say it will not work for 2008 failover clustering. I'm interested in seeing something suitable for failover in a production environment, but with very low IO requirements. (Clustering, say, a 30GB DB.) As for using software: On Windows, StarWind seems to have a great solution. But it's actually more money than buying a hardware SAN. (As I understand, only the enterprise edition supports having replicas, and that's $3000 a license.) I was thinking I could use Linux, something like DRBD + an iSCSI target would be fine. However, I haven't seen any free or low-cost iSCSI software that supports SCSI-3 persistent reservations, which Windows 2008 needs for failover clustering. I know $6K isn't much at all, just curious to see if there are practical cheaper solutions out there. And finally, yes, the software is expensive, but many small business get MS BizSpark, so the Windows 2008 Enterprise / SQL 2008 licenses are completely free.

  Read the article

• How do you monitor SSD wear in Windows when the drives are presented as 'generic' devices?

  - by MikeyB

  Under Linux, we can monitor SSD wear fairly easily with smartmontools whether the drive is presented as a normal block device or a generic device (which happens when the drive has been hardware RAIDed by certain controllers such as the one on the IBM HS22). How can we do the equivalent under Windows? Does anyone actually use smartmontools? Or are there other packages out there? The problem is that SCSI Generic devices just don't show up in Windows. If the drives aren't RAIDed we can see them fine. How I'd do it in Linux: sles11-live:~ # lsscsi -g [1:0:0:0] disk SMART USB-IBM 8989 /dev/sda /dev/sg0 [2:0:0:0] disk ATA MTFDDAK256MAR-1K MA44 - /dev/sg1 [2:0:1:0] disk ATA MTFDDAK256MAR-1K MA44 - /dev/sg2 [2:1:8:0] disk LSILOGIC Logical Volume 3000 /dev/sdb /dev/sg3 sles11-live:~ # smartctl -l ssd /dev/sg1 smartctl 5.42 2011-10-20 r3458 [x86_64-linux-2.6.32.49-0.3-default] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net Device Statistics (GP Log 0x04) Page Offset Size Value Description 7 ===== = = == Solid State Device Statistics (rev 1) == 7 0x008 1 26~ Percentage Used Endurance Indicator |_ ~ normalized value sles11-live:~ # smartctl -l ssd /dev/sg2 smartctl 5.42 2011-10-20 r3458 [x86_64-linux-2.6.32.49-0.3-default] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net Device Statistics (GP Log 0x04) Page Offset Size Value Description 7 ===== = = == Solid State Device Statistics (rev 1) == 7 0x008 1 3~ Percentage Used Endurance Indicator |_ ~ normalized value

  Read the article

• Poor Write Performance in VM inside Proxmox PVE 2.0

  - by sorsenne

  I am running a PVE 2.0 on a decent Hardware (2 SATA HDDs as RAID1, 12GB RAM, i7 CPU) but the I/O Performance is very poor inside the VM (Ubuntu 11.10 Server). The very same VM was copied to another Server running simply Ubuntu Server with KVM and had better I/O Perf. this is how the HDD is shown in the Guest: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata1.00: ATA-8: ST3000DM001-9YN166, CC49, max UDMA/133 ata1.00: 5860533168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA ST3000DM001-9YN1 CC49 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 0:0:0:0: [sda] 4096-byte physical blocks sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA I tested with DD: $ dd bs=1M count=128 if=/dev/zero of=test conv=fdatasync 128+0 records in 128+0 records out 134217728 bytes (134 MB) copied, 19.2222 s, 7.0 MB/s on the Host, this same Test will result with 156 MB/s in average. PS: I am using VirtIO and see no error in dmesg.

  Read the article

• I/O Error on LG GSA-H12N DVD drive on Windows 7

  - by Ashwin

  I am facing an I/O Error when I try to burn DVD data discs on my LG GSA-H12N DVD drive on Windows 7. Note that I was able to do this same operation on the same hardware/software just a day earlier without any problems, but with Windows XP. The only change (AFAIK) has been the installation of Windows 7 to replace Windows XP on this PC. Here is the error I get when I try to burn a DVD data disc using CDBurnerXP 4.2.7.1801: Burning error occured An error occured while burning the disc. Most likely the disc is not usable. Usually these errors happen if the inserted media is not compatible to the drive or of poor quality. (devNTSPTI_IO_Error) Could not write to Disc (LBA: 52864 Length: 32). SCSI Pass-through Interface I/O Error. - 0xFF045D Note that there can be no problem with the discs since I have been using the same discs (from the same box) just before the Windows 7 installation with no problems. The only change has been Windows 7. I tried InfraRecorder v0.5 and ImgBurn v2.5 and got similar I/O errors: Note that Windows 7 lists the LG GSA-H21N drive as being compatible (see this link). I also checked the LG Drivers website and using the firware update from there updated the drive firmware from version UL01 to UL02. But, even this has not helped. The drive reads DVDs without any problem, but continues to produce coasters. Could someone help me figure out what is the problem? Thanks :)

  Read the article

• NFS high CPU usage

  - by user269836

  Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

  Read the article

• linux hardware raid 10 / lvm / virtual machine partition alignment and filesystem optimization

  - by Jason Ward

  I've been reading everything I can find about partition alignment and filesystem optimization (ext4 and xfs) but still don't know enough to be confident in setting up my current configuration. My remaining confusion comes from the LVM layer and if I should use raid parameters on the filesystem in guest os'es. My main questions are: When I use 'pvcreate --dataalignment' do I use the stripe-width as calculated for a filesystem on RAID (128kB for ext4 in my situation), the Stripe size of the RAID set (256kB), something else altogether, or do I not need this? When I create ext2/3/4 or xfs filesystems in guests on the Logical Volumes, should I add the settings for the underlying RAID (e.g. mkfs.ext4 -b 4096 -E stride=64,stripe-width=128)? Does anyone see any glaring errors in my set up below? I'm running some benchmarks now but haven't done enough to start comparing results. I have four drives in RAID 10 on a 3ware 9750-4i controller (more details on the settings below) giving me a 6.0TB device at /dev/sda. Here is my partition table: Model: LSI 9750-4i DISK (scsi) Disk /dev/sda: 5722024MiB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1.00MiB 257MiB 256MiB ext4 BOOTPART boot 2 257MiB 4353MiB 4096MiB linux-swap(v1) 3 4353MiB 266497MiB 262144MiB ext4 4 266497MiB 4460801MiB 4194304MiB Partition 1 is to be the /boot partition for my xen host. Partition 2 is swap. Partition 3 is to be the root (/) for my xen host. Partition 4 is to be (the only) physical volume to be used by LVM (for those who are counting, I left about 1.2TB unallocated for now) For my Xen guests, I usually create a Logical Volume of the needed size and present it to the guests for them to partition as needed. I know there are other ways of handling that but this method works best for my situation. Here's the hardware of interest on my CentOS 6.3 Xen Host: 4x Seagate Barracuda 3TB ST3000DM001 Drives (sector size: 512 logical/4096 physical) 3ware 9750-4i w/BBU (sector size reported: 512 logical/512 physical) All four drives make up a RAID 10 array. Stripe: 256kB Write Cache enabled Read Cache: intelligent StoreSave: Balance Thanks!

  Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18  | Next Page >