Search Results

Search found 36498 results on 1460 pages for 'linux usb drive'.

Page 178/1460 | < Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >

  • Using portable Mode for true crypt for crypting Portable HDD , USB etc

    - by Gaurav_Java
    I was wondering how to encrypt my external HDD so that my data would be safe AND accessible from any OS platform (Windows and Linux). So I went through many posts and forums and found out the best thing was to use true crypt. I went along with this post and encrypt my USB drive. When inserted that, Windows didn't recognize it. Then I followed another post that said to install truecrypt. The thing is : How can i use traveler disk setup in Ubuntu (Option not found)? Install truecrypt in USB so that i can *mount my USB or HDD on any other OS? If there is no solution for the upper two, then is there any other software which I can use to encrypt an USB device so that it can be accessed from any OS?

    Read the article

  • How do you limit root partition disk access to allow drive to go into stanby mode?

    - by Casey
    When there are no users on my system, I would like the hard disk to spindown to low-power state. I realize that this might not be 100% achievable for a straight 24 hours, but it seems reasonable that the system could remain idle for a few hours at a time when it is not in use. My system is headless and running a limited number of services. The primary services are: exim4, mythtv-backend, nfs, samba, cups, apt-cacher-ng Assume that drives are already enabled to go into standby mode. Also, its not acceptable to increase the write-back timeout, since my system is not on a UPS.

    Read the article

  • Recover files in Ubuntu from USB stick

    - by Jon
    I have Ubuntu 11.04 running from a USB stick. I think I ran some updates in terminal and now it has a kernel panic during boot up. Is there a way I can get hold of files I saved when Ubuntu was working? I just managed to watch the booot screen and it looks as if there are some errors saying there is no room to write to disk however my USB stick has 5GB free UPDATE: Here is what I see when I plug the USB stick into Windows

    Read the article

  • Intel intègrera l'USB 3.0 dans Windows 8 et espère aider l'adoption de masse de cette technologie

    Mise à jour du 09.03.2010 par Katleen Intel intègrera l'USB 3.0 dans Windows 8 et espère aider l'adoption de masse de cette technologie Une information importante vient d'être révèlée à propos du futur système d'exploitation de Microsoft. En effet, Intel a annoncé hier que l'USB 3.0 sera embarqué dans Windows 8. Alors que les technologies qui seront utilisées dans deux ans sont encore inconnues, que penser de cette fonctionnalité ? L'USB 3.0, qui a été présenté pour la première fois au public le 18 septembre 2007 lors de l'Intel Developer Forum, apporte un bus capable de transferts ultra-rapides à hauteur de 4 Gbit/s Pour rappel, l'USB 2.0 plafonne à 480 Mbits/s. ...

    Read the article

  • Is it possible to execute keyboard input programmatically in Linux?

    - by Taylor Hawkes
    For example is there a Linux command or way that I could from a program (c++ | python| or other) enter a series of keyboard inputs that are interpreted as though they are keyboard inputs. I have a bad case of Repetitive Stress Injury (RSI) from typing. To ease my pain I developed a voice controlled interface using pocket sphinx and a custom grammar and to run a number of very common commands. ex: "open chrome" , "open vim". Basically what is shown here, but with slightly diff tools: http://bloc.eurion.net/archives/2008/writing-a-command-and-control-application-with-voice-recognition/ I have run into some limitation as I can only execute command line commands given a voice command. Rather than having a "voice command" - "command line command" mapping, I would like to have "voice command" - "keyboard input" mapping. So when my active window is a browser and I type + n, and new tab opens. If I'm in vim and new vim tab opens. Any suggestions, ideas, tools or approaches to this problem would be much appreciated. I understand the answer may not be simple, but would like to develop it none the less.

    Read the article

  • Numpad doesn't work after booting up - forced to reconnect USB keyboard after startup

    - by HorusKol
    I've tried this on two different USB keyboards - both of which work fine on a different computer running Windows XP. For some reason, the numerical keypad doesn't work probably immediately after booting up - neither the numbers work, nor the 'home' commands and so on that you can use with the numlock off. It doesn't make a difference whether I press numlock on or off - the keypad doesn't work correctly no matter what state this is in. However, once I've booted the machine I can disconnect/reconnect the USB connector for the keyboard, and it will work exactly as expected. I'm running Gnome on Ubuntu 10.04. The only other USB devices connected is a mouse - and I've experienced no problems with that. This is a direct connection to the box (not via an external USB hub)

    Read the article

  • is it possible to execute keyboard input programmaticly in linux?

    - by Taylor Hawkes
    For example is there a Linux command or way that I could from a program (c++ | python| or other) enter a serious of keyboard inputs that are interpreted as though they are keyboard inputs. I have a bad case of RSI from typing. To ease my pain I developed a voice controlled interface using pocket sphinx and a custom grammar and to run a number of very common commands. ex: "open chrome" , "open vim". basically what is shown here, but with slightly diff tools: http://bloc.eurion.net/archives/2008/writing-a-command-and-control-application-with-voice-recognition/ I have run into some limitation as I can only execute command line commands given a voice command. Rather than having a "voice command" - "command line command" mapping I would like to have "voice command" - "keyboard input" mapping. So when my active window is a browser and i type + n, and new tab opens. If i'm in vim and new vim tab opens. Any suggestions, ideas, tools or approaches to this problem would be much appreciated. I understand the answer may not be simple, but would like to develop it none the less.

    Read the article

  • Problem in installing Ubuntu 12 using USB

    - by Hitesh Bhatt
    I have a Sony laptop (VPCEH25EN) and i am trying to install Ubuntu 12.04 LTS. I downloaded the iso named "ubuntu-12.04-desktop-amd64.iso". For installing i created a bootable USB using UltraISO. When i booted the USB it hangs and shows " Booting from USB ", I even left it for hours and it didn't moved a bit. When I booted the ISO in Virtual Box, it ran well. I even used other tools to make a bootable USB, then it says " BOOTMNGR missing ". Please help, I am new to Ubuntu and my optical drive is fried. Thanks in advance..

    Read the article

  • Reminder: Oracle Linux 5 Exams Soon To Retire

    - by Brandye Barrington
    This is a reminder that Oracle will retire Oracle Linux System Administration (1Z0-403) and Oracle Linux Fundamentals (1Z0-402) on October 31, 2013. We will also re-release exam 1Z0-402 as Oracle Linux Fundamentals (1Z0-409) on November 1, 2013. New Oracle Linux 5 and 6 OCA and OCP certifications are now available. Existing certification holders should note that these retirements suspend the delivery of any further exams, but do not affect your certification. If you currently hold a certification earned by one of these exams, your credential remains fully valid. Retiring Certification Path Oracle Linux Administrator Certified Associate Retiring Exam 1Z0-402 Oracle Linux Fundamentals (this will be re-released as Oracle Linux Fundamentals (1Z0-409) and lead to the  Oracle Linux Certified Implementation Specialist certification.) 1Z0-403 Oracle Linux System Administration These exams will continue to be offered through October 31, 2013. Candidates pursuing these certification paths must successfully complete the required certification exams by this date. Re-takes will not be available after this date. For more information, see Oracle Certification retirements. For more information on the new exams and certifications, see the Oracle Certification Blog.

    Read the article

  • USB-live does not save files between sessions

    - by Mads Skjern
    I created a USB-stick with Ubuntu, using the recommended tool "Startup Disk Creator" and the image for Ubuntu 13.10. The very simple interface looks like this: There can't be much to misunderstand in this GUI. I have chosen to create a USB stick with a live version of Ubuntu, which will save files and settings from session to session, on the USB drive, right? Well, it just doesn't save anything. I go in, create a file on Desktop, restart and it's gone. I did the whole procedure three times, i.e. first creating the USB, then testing if I could save. Have I misunderstood something?

    Read the article

  • Various issues linked to my CD drive, when it has a disc in it

    - by Voyagerfan5761
    When I go to the Desktop and click on a media icon (for my flash drive, a CD, whatever it is), the following problems occur, in this approximate sequence: Nautilus will close if it's open. the desktop icons disappear my Window List shows a button that says "Starting File Manager" the icons reappear the button in Window List disappears Because of this problem, I can no longer drag and drop media, nor can I right-click to perform actions such as "Eject" and "Safely Remove Drive". The same symptoms occur if I click a media icon (that is also present on the desktop) in Nautilus' Computer view, though notably not if I click in the places list on the left. I have confirmed that this problem happens only if there is a CD in the drive (Matshita UJDA360). Also, inserting a disc into the CD drive appears to kill all running programs and restart Nautilus (or X; I'm not sure). Applications like Brasero and Rhythmbox will not start while there is a disc in the drive. Removing the disc doesn't result in the list of media updating; it must be forced to update by clicking on one of the desktop icons and going through one of the above-described cycles. It doesn't seem to matter what type of disc is in the drive. This has happened with CD-RWs I burned years ago using Roxio on Windows XP, the Ubuntu disc I installed from (burned with InfraRecorder Portable under Windows XP), and the retail game disc for Star Trek Armada II. The first indication of a problem was Brasero dying when I tried to insert a disc for erasure and rewriting. Since then, I've drafted several different questions on various issues, finally combining them into this one when I realized that having a CD in the drive was the common link. Could this be a simple driver issue? If Ubuntu is dynamically detecting my hardware on boot, can I specify drivers for devices that I know will be a problem if the default files are used? I'm beginning to think that my laptop, an old Dell Inspiron 2650, is just too old or proprietary-driver-hungry (or something, maybe RAM-starved) for Ubuntu and Windows XP to play nicely alongside each other. Or maybe I just need to carefully take my wall-wart machine to a coffee shop for an afternoon so I can download updates and such from the Internet, as I lack a home connection.

    Read the article

  • HP dv6910 laptop no longer recognizes wireless adapter, dvd drive, and one usb port. What can I do about this?

    - by Joan H.
    In the last 3 weeks, my not even 3 year old HP laptop (vista) just seems to be failing. First, one of the usb ports stopped working. Next, the dvd drive all of a sudden was not recognized as even existing, so it is now useless. And as of today, I no longer seem to have a wireless adapter on my laptop. It doesn't show up in device manager, same as the dvd drive. I can connect to the internet by ethernet cable, but not wirelessly. It worked fine last night; now it doesn't even exist! I have tried a 'hard reset' I read about on HP's forum- no help. I am not sure what else to try. I read about the USB wifi dongle in another response, but I already have maxed our my usb ports even though I have bought a USB hub since the one port failed. Plus, I'd like my laptop to just work like it's supposed to instead of being jerry rigged with usb hubs, external dvd drives, and wifi dongles etc. Any ideas?

    Read the article

  • USB mouse pointer only moving horizontally on macbook 6.2 with 12.04

    - by Glyn Normington
    After installing Ubuntu 12.04 on a macbook pro 6.2, the touchpad and external USB mouse worked perfectly. After rebooting I can't get either touchpad or external USB mouse to work. Sometimes no mouse pointer is visible, but more often I can only move the mouse pointer horizontally five sixths of the way across the display (from the top left). I have uninstalled mouseemu. xinput list shows the USB mouse. xinput query-state for the USB mouse shows the following: ButtonClass button[1]=up ... button[16]=up ValuatorClass Mode=Relative Proximity=In valuator[0]=480 valuator[1]=2400 valuator[2]=0 valuator[3]=3 and re-issuing this command with the pointer at its right hand extreme displays the same except for: valuator[0]=1679 So the valuator[0] seems to be the x-coordinate of the pointer and the range of motion 480-1679 is indeed about five sixths of the display width (1440). valuator[1] is suspiciously large given the display height is 900. Perhaps this is a side-effect of having previously been using a dual monitor (although booting with that monitor connected does not help). There are other entries listed under xinput list: Virtual core XTEST pointer which seems stuck at position (840,1050). bcm5974 which seems stuck at position (837,6700). Removing the bcm5974 module using rmmod disables the toucpad as expected but does not fix the USB mouse problem. After adding the module back, it is stuck at position (840,1050) instead of (837,6700). /etc/X11/xorg.conf was generated by nvidia-settings and contains: Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "ZAxisMapping" "4 5" although I don't know how plausible these settings are. Any suggestions?

    Read the article

  • Install Ubuntu in UEFI mode (unable to boot from USB)

    - by Adele
    I recently bought a Dell Inspiron 15R SE with Windows 8 (64 bit) pre-installed (UEFI supported). I want to install Ubuntu in dual boot with Windows 8. I tried to follow all instruction here : https://help.ubuntu.com/community/UEFI And here : Installing Ubuntu on a Pre-Installed Windows 8 (64-bit) System (UEFI Supported) So, I set Secure Boot to "off" into BIOS and I disable Fast Startup as described here : http://www.eightforums.com/tutorials/6320-fast-startup-turn-off-windows-8-a.html I created a bootable USB key for Ubuntu (Ubuntu 13.10 64bits international Edition) with Unetbootin. The problem is I am unable to boot from the USB key. The computer tries to boot into infinite loop. I also tried to boot from USB with "Legacy Boot" option instead of UEFI. In this case, the computer says there are no bootable devices. Of course, I tried to boot from my USB key on an other computer having normal BIOS and it works perfectly. Have you ideas about what I need to do to be able to boot from USB ? Thanks in advance for your help, Adele

    Read the article

  • Architectural approaches to creating a game menu/shell overlay on PC/Linux?

    - by Ghopper21
    I'm am working on a collection of games for a custom digital tabletop installation (similar to Microsoft Surface tables). Each game will be an individual executable that runs full-screen. In addition, there needs to be a menu/shell overlay program running simultaneously. The menu/shell will allow users to pause games, switch to other games, check their game history, etc. Some key requirements of the shell: it intercepts all user input (mainly multitouch) first before passing it on to the currently running game (so that it can, for instance, know to pop-up at a "pause" command); can reveal on arbitrary portions of the screen, with the currently running (but presumably paused) game still showing underneath, ideally with its shape/size being dynamic, to allow for creation of an animated in/out drawer effect over the game. I'm currently looking into different architectural approaches to this problem, including Fraps and DirectX overlays, but I'm sure I'm missing some ways to think about this. What are the main approaches I should be considering? (Note the table is currently being run by Windows PC, but it could potentially be a Linux box instead.)

    Read the article

  • Unable to boot from new SSD after installing from USB

    - by user73725
    I'm using a new SSD with nothing on it. It's installed via USB drive, and boots from USB as well. While in Ubuntu I can see the SSD and other devices. When I install from the desktop (have tried from the boot screen as well), system restarts. It takes me to the boot screen, select boot from first hard disk, nothing, goes right back to boot screen. When I take the USB out, it hangs on "Verifing DMI." If I boot onto the USB I can see the correct files located in the SSD. I have a basic knowledge of computers. Give me any thing you think would help. No other OS's are loaded. Gigabyte ga-k8n-sli 1GB RAM AMD Athlon 64 x2 dual core 3800+ OCZ SSD Agility 3 120GB

    Read the article

  • Linux, GNU GCC, ld, version scripts and the ELF binary format -- How does it work? [closed]

    - by themoondothshine
    I'm trying to learn more about library versioning in Linux and how to put it all to work. Here's the context: I have two versions of a dynamic library which expose the same set of interfaces, say libsome1.so and libsome2.so. An application is linked against libsome1.so. This application uses libdl.so to dynamically load another module, say libmagic.so. Now libmagic.so is linked against libsome2.so. Obviously, without using linker scripts to hide symbols in libmagic.so, at run-time all calls to interfaces in libsome2.so are resolved to libsome1.so. This can be confirmed by checking the value returned by libVersion() against the value of the macro LIB_VERSION. So I try next to compile and link libmagic.so with a linker script which hides all symbols except 3 which are defined in libmagic.so and are exported by it. This works... Or at least libVersion() and LIB_VERSION values match (and it reports version 2 not 1). However, when some data structures are serialized to disk, I noticed some corruption. In the application's directory if I delete libsome1.so and create a soft link in its place to point to libsome2.so, everything works as expected and the same corruption does not happen. I can't help but think that this may be caused due to some conflict in the run-time linker's resolution of symbols. I've tried many things, like trying to link libsome2.so so that all symbols are alised to symbol@@VER_2 (which I am still confused about because the command nm -CD libsome2.so still lists symbols as symbol and not symbol@@VER_2), but nothing seems to work. What am I doing wrong?

    Read the article

  • Illuminated USB keyboard flickers

    - by Axj Member
    Does anyone know where I can download a driver for the VAKOSS TK-487-UK illuminated keyboard to run on Ubuntu? Or at least how to control the USB port so that it stops flickering on and off. The USB port works fine but the Keyboard is not recognized by Ubuntu... Already read the post on youtube and script but did not work either...tried changing USB ports, rebooting, etc. This has been going on for a week. The keyboard gets its power from the USB port. http://answers.yahoo.com/question/index?qid=20120128105854AAjgmgn

    Read the article

  • how to use gparted to partion 2 drives as 1

    - by user281745
    I have my lenovo t43 and I have a SATA extra HD drive instead of the CD drive and I have in it a 250 GB hard drive and in my HD caddy I have a 40 GB hard drive I would like to use gparted to partition these 2 drives as 1 i would like to have the 250 GB as a extended part of the 40 GB cause i already have Ubuntu Installed on it, they are right now not side by side im not sure how to do this so please list by step by step thank you http://imgur.com/dE0B7dy,qRRPgoB http://imgur.com/dE0B7dy,qRRPgoB#1

    Read the article

  • Hard drive skipped in boot

    - by Yasin
    Good evening. I just installed Ubuntu 12.04 using a USB, but right after the install, after restarting the machine, I get a message asking me to insert a bootable drive. My boot settings in Bios have the hard drive first, then DVD, then USB stick, and I have two systems installed, Windows 7 and Ubuntu 12.04. I suspected the hard drive got somehow disconnected internally, so I checked but everything was in place. I used the live USB to start Ubuntu, and I could see the hard drive and mount whatever partition I wanted. The one that contains the recently installed Ubuntu, looks the same. (It hasn't been deleted or anything). I'm not sure if this is a hardware problem or a loader(grub) problem, because the hard drive is visible. Only it isn't seen by the BIOS. My only means of internet connection is a USB modem, which doesn't work when I'm using the live USB, so I have can't download anything from the internet, in case someone asks. I also reinstalled Ubuntu 12.04, to no avail. This is my second problem with this laptop, and Ubuntu, and it's not even a week old. I hope this one gets solved. Thank you.

    Read the article

  • installing application packages on ubuntu usb

    - by mazel
    I'm new to ubuntu. I downloaded the newest version on a usb stick then I booted my PC with the usb. upon trying out ubuntu I tried installing additional packages/applications, which worked fine. BUT when I then after tried using my ubuntu usb, the new installed apps were not there! if I get that right, ubuntu would only install new packages to the actual PC I'm using it on. not within ubuntu itself!? is there a way that I can install new applications to my ubuntu usb and it should stay within ubuntu so I can use it for other pc's which don't have an internet connection necessary to update/install packages ? thanks so much

    Read the article

  • Grub rescue doesn't allow me to boot from LIVE CD/USB

    - by Thameem
    I used to have Windows Vista & Ubuntu 12.04 on dual boot. Accidentally, I deleted the Linux partition and landed on Grub rescue on the next boot. The tricky thing for me here is I have been trying to boot through LIVE CD/USB of the ubunutu version, other linux versions but in vain. What happens is, it appears as if it reads the CD/DVD drive or the USB flashes for a while when trying to boot through LIVE versions but the Grub rescue appears after a while. The only option I could think here is to remove the hard disk and connect to the other laptop I have through USB and reinstall a fresh OS. Please suggest me a way to boot through the DVD/USB again. My laptop is Sony VAIO CR32 series.Thanks.

    Read the article

  • No upgrade option when booting from USB (12.04)

    - by Ramzi Njeim
    I am trying to upgrade my ubuntu 11.10, i know that it is better to upgrade using a live cd/usb, i booted from the live usb, followed the instructions as usual, but only found three options: Cleen install Install alongside your other operating systems Other The upgrade choice was missing. I even tried installing it after running ubuntu 12.04 from usb, and ended up with the same result. I have a dual boot Ubuntu 11.10 and Windows 7, i think it is only seeing the windows 7 and missing the ubuntu 11.10 partition. Any help ?

    Read the article

  • Cannot boot from USB wtih ubuntu 13.10

    - by arunkant
    I downloaded ubuntu 13.10 amd64 iso and used all of following methods to make a install media. UNetBootin Universal USB installer (from windows) But I cannot boot from USB pen drive. Some time it just drop me in grub menu of previously installed ubuntu 13.04. Sometime it show a message "Could not open //fallback.efi: 14 ..." for a moment and then just stays there(blank screen). How to boot from USB pen drive?

    Read the article

  • Why might my Fedora 15 live USB persistent storage not work?

    - by Richard J Foster
    I created a Fedora 15 "live" USB stick using the live USB creator found at https://fedorahosted.org/liveusb-creator/ and the Fedora 15 i686 Desktop ISO image with the persistent storage space set to 4096MB. (The USB stick I have available has an 8GB capacity, so there should be plenty of space.) Fedora appears to boot correctly, however it seems that the persistent storage is not working. To verify this, I opened a terminal prompt, then did su - followed by yum update yum. As expected, I was informed that a new version was available. (The live CD contains version 3.2.29-4, at the time of typing 3.2.29-6 is the current version). After installing, I verified that the new version was installed by typing yum --version. I then shutdown the system using shutdown now. After the system had shut down, I rebooted and returned to the terminal prompt. On typing yum --version, I was informed that the version was 3.2.29-4 (i.e. the original version). Why might the persistent storage not be working? Is there anything I can do to fix it?

    Read the article

< Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >