Search Results

Search found 27302 results on 1093 pages for 'annoyed to no end'.

Page 182/1093 | < Previous Page | 178 179 180 181 182 183 184 185 186 187 188 189  | Next Page >

• multiple streaming servers behind a Bastion Host

  - by Bond

  I am using open source streaming server Red5 on multiple servers. Which are running behind a bastion host. the world knows these sites as http://site1.mydomain.com http://site2.mydomain.com http://site3.mydomain.com http://site4.mydomain.com To reach the front end server is using Apache Reverse Proxy. I am also having video streaming on each of these websites using rtmp. To be able to reach the streaming server I embed a javascript in HTML pages as follows Code: <embed ..... var="rtmp://site1.my_domain.com" > the problem is the website are many site1.mydomain.com site2.mydomain.com site3.mydomain.com site4.mydomain.com each on a separate physical server. Each of these four have their own Red5 installations the front end to each of these four is a common Bastion Host. If I run rtmp on each of the subdomains at a different port how will I make sure a request such as rtmp://site1.mydomain.com rtmp://site2.mydomain.com goes to their respective servers. from the front end server. What do I need to handle in this case ? IPTABLES came to mind instantly but from the client browser on internet when some one requests rtmp://site1.mydomain.com how will I make sure this rtmp request is mapped to a port different than 1935 as there are three other streaming servers which are also to respond to their respective requests ?

  Read the article

• Is "DSLAM congestion" a legitimate reason for slow DSL?

  - by Jay Bazuzi

  My DSL has been extremely slow in the evenings recently. To test it, I telnet to my DSL Modem, and ping the gateway. This way I eliminate internet congestion and local network issues. In the mornings I get 30ms - 50ms pings. In the evenings, it bounces around a lot, but 10000ms pings are common. I complained to Qwest support, and they said it was a known issue on their end, their engineers were working on it, and wouldn't say anything else. A couple days later I complained again, and they sent out a technician. He tested my house wiring and found that one of them had a short. It was an unused line, so we disconnected it, and he said things looked better and left. My daytime speeds improved at this point, but evening is still bad. I complained to Qwest support again, and they said it was a problem with DSLAM congestion at their end, and that they were working on it, but no ETA. My neighbor has Qwest DSL and doesn't seem to have these problems. That seems strange. I go use her network when I absolutely must get online and mine is behaving badly. I can't tell if they're yanking my chain or not. Regardless, these speeds are crap. I'm paying for 7Mpbs but am lucky if I get 1/10th that in the evenings. My kids like to watch Netflix streaming movies, and it's just impossible after 5pm or so. Should I wait it out? Will complaining again produce any results? Should I change my subscription to a lower speed until they fix their end? Or switch to cable?

  Read the article

• Why is Windows Update trying to install an update I don't need?

  - by Oliver Salzburg

  I have a Windows 7 system that currently has a single update pending: Windows Internet Explorer 9 for Windows 7 for x64-based Systems If I try to install the update, Windows Update will: Create a restore point Fail with the error: Code 9C48 Windows Update encountered an error. The event log for the event reads: Installation Failure: Windows failed to install the following update with error 0x80070643: Windows Internet Explorer 9 for Windows 7 for x64-based Systems. If you search the web for that error, there are many other people with the exact same issue. Sadly, I am unable to apply the proposed solutions to my case, because I just installed this system. There is nothing on it, except Windows 7. I installed the system and ran through the updates. I also did the exact same process with this machine several times over the past few days due to a long-term test we just started. I didn't have any problems with any Windows Update on the previous installation runs and I know I didn't do anything different this time because I followed the installation procedures instructions which are to be used during the test. How did this happen and how do I solve it? Further Investigation So, as I always like to do, I ran the update again while running Process Monitor and dug up further details. WindowsUpdate.log First of all, there is a Windows Update log file located at C:\Windows\WindowsUpdate.log which I didn't know about. But I fail to see any significant entry in it, maybe you're more lucky: 2012-04-10 22:46:58:017 956 728 AU AU received approval from Ux for 1 updates 2012-04-10 22:46:58:017 956 728 AU AU setting pending client directive to 'Progress Ux' 2012-04-10 22:46:58:095 956 728 AU BeginInteractiveInstall invoked for Download 2012-04-10 22:46:58:095 956 728 AU Auto-approving update for download, updateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}.100, ForUx=1, IsOwnerUx=1, HasDeadline=0, IsMinor=0 2012-04-10 22:46:58:095 956 728 AU Auto-approved 1 update(s) for download (for Ux) 2012-04-10 22:46:58:110 956 728 AU UpdateDownloadProperties: 0 download(s) are still in progress. 2012-04-10 22:46:58:110 956 728 AU ############# 2012-04-10 22:46:58:110 956 728 AU ## START ## AU: Download updates 2012-04-10 22:46:58:110 956 728 AU ######### 2012-04-10 22:46:58:110 956 728 AU # Approved updates = 1 2012-04-10 22:46:58:110 956 728 AU AU initiated download, updateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}.100, callId = {35DF928B-B428-4BAC-8C63-55295967EFBB} 2012-04-10 22:46:58:110 956 728 AU Setting AU scheduled install time to 2012-04-11 01:00:00 2012-04-10 22:46:58:110 956 728 AU Successfully wrote event for AU health state:0 2012-04-10 22:46:58:110 956 728 AU Currently showing Progress UX client - so not launching any other client 2012-04-10 22:46:58:110 956 bb8 DnldMgr ************* 2012-04-10 22:46:58:110 956 bb8 DnldMgr ** START ** DnldMgr: Downloading updates [CallerId = AutomaticUpdatesWuApp] 2012-04-10 22:46:58:110 956 bb8 DnldMgr ********* 2012-04-10 22:46:58:110 956 bb8 DnldMgr * Call ID = {35DF928B-B428-4BAC-8C63-55295967EFBB} 2012-04-10 22:46:58:110 956 bb8 DnldMgr * Priority = 3, Interactive = 1, Owner is system = 0, Explicit proxy = 0, Proxy session id = 1, ServiceId = {9482F4B4-E343-43B6-B170-9A65BC822C77} 2012-04-10 22:46:58:110 956 bb8 DnldMgr * Updates to download = 1 2012-04-10 22:46:58:110 956 bb8 Agent * Title = Windows Internet Explorer 9 for Windows 7 for x64-based Systems 2012-04-10 22:46:58:110 956 bb8 Agent * UpdateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}.100 2012-04-10 22:46:58:110 956 bb8 Agent * Bundles 1 updates: 2012-04-10 22:46:58:110 956 bb8 Agent * {6D9A90B7-FAF9-4A47-9EFE-A506264873B3}.100 2012-04-10 22:46:58:110 956 bb8 DnldMgr *********** DnldMgr: New download job [UpdateId = {6D9A90B7-FAF9-4A47-9EFE-A506264873B3}.100] *********** 2012-04-10 22:46:58:110 956 728 AU Successfully wrote event for AU health state:0 2012-04-10 22:46:58:110 956 728 AU # Pending download calls = 1 2012-04-10 22:46:58:110 956 728 AU ## RESUMED ## AU: Download update [UpdateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}, succeeded] 2012-04-10 22:46:58:313 956 bb8 Agent ** END ** Agent: Downloading updates [CallerId = AutomaticUpdatesWuApp] 2012-04-10 22:46:58:313 956 bb8 Agent ************* 2012-04-10 22:46:58:313 956 718 AU ######### 2012-04-10 22:46:58:313 956 718 AU ## END ## AU: Download updates 2012-04-10 22:46:58:313 956 718 AU ############# 2012-04-10 22:46:58:313 956 718 AU Setting AU scheduled install time to 2012-04-11 01:00:00 2012-04-10 22:46:58:313 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:46:58:313 956 718 AU Currently showing Progress UX client - so not launching any other client 2012-04-10 22:46:58:313 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:46:58:313 956 aac AU Getting featured update notifications. fIncludeDismissed = true 2012-04-10 22:46:58:313 956 aac AU No featured updates available. 2012-04-10 22:47:00:107 956 aac AU BeginInteractiveInstall invoked for Install 2012-04-10 22:47:00:107 956 aac AU Auto-approving update for install, updateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}.100, ForUx=1, IsOwnerUx=1, HasDeadline=0, IsMinor=0 2012-04-10 22:47:00:107 956 aac AU Auto-approved 1 update(s) for install (for Ux), installType=1 2012-04-10 22:47:00:107 956 aac AU ############# 2012-04-10 22:47:00:107 956 aac AU ## START ## AU: Install updates 2012-04-10 22:47:00:107 956 aac AU ######### 2012-04-10 22:47:00:107 956 aac AU # Initiating manual install 2012-04-10 22:47:00:107 956 aac AU # Approved updates = 1 2012-04-10 22:47:00:107 956 aac AU ## RESUMED ## AU: Installing update [UpdateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}] 2012-04-10 22:47:13:773 2232 9fc Handler : WARNING: Exit code = 0x8024200B 2012-04-10 22:47:13:773 956 718 AU # WARNING: Install failed, error = 0x80070643 / 0x00009C48 2012-04-10 22:47:13:773 2232 9fc Handler ::::::::: 2012-04-10 22:47:13:773 2232 9fc Handler :: END :: Handler: Command Line Install 2012-04-10 22:47:13:773 2232 9fc Handler ::::::::::::: 2012-04-10 22:47:13:851 956 a7c Agent ********* 2012-04-10 22:47:13:851 956 a7c Agent ** END ** Agent: Installing updates [CallerId = AutomaticUpdates] 2012-04-10 22:47:13:851 956 718 AU Install call completed. 2012-04-10 22:47:13:851 956 a7c Agent ************* 2012-04-10 22:47:13:851 956 718 AU # WARNING: Install call completed, reboot required = No, error = 0x00000000 2012-04-10 22:47:13:851 956 718 AU ######### 2012-04-10 22:47:13:851 956 718 AU ## END ## AU: Installing updates [CallId = {FCFF2A5C-25AB-4FB9-AB2B-35C65CCA6A9F}] 2012-04-10 22:47:13:851 956 718 AU ############# 2012-04-10 22:47:13:851 956 718 AU Install complete for all calls, reboot NOT needed 2012-04-10 22:47:13:851 956 718 AU Setting AU scheduled install time to 2012-04-11 01:00:00 2012-04-10 22:47:13:851 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:47:13:851 956 498 AU Getting featured update notifications. fIncludeDismissed = true 2012-04-10 22:47:13:851 956 498 AU No featured updates available. 2012-04-10 22:47:14:366 956 168 AU No featured updates notifications to show 2012-04-10 22:47:14:366 956 168 AU UpdateDownloadProperties: 0 download(s) are still in progress. 2012-04-10 22:47:14:366 956 168 AU Triggering Offline detection (non-interactive) 2012-04-10 22:47:14:366 956 168 AU AU setting pending client directive to 'Install Complete Ux' 2012-04-10 22:47:14:366 956 168 AU Changing existing AU client directive from 'Progress Ux' to 'Install Complete Ux', session id = 0x1 2012-04-10 22:47:14:366 956 168 AU Successfully wrote event for AU health state:0 2012-04-10 22:47:14:366 956 b78 AU ############# 2012-04-10 22:47:14:366 956 b78 AU ## START ## AU: Search for updates 2012-04-10 22:47:14:366 956 b78 AU ######### 2012-04-10 22:47:14:366 956 b78 AU ## RESUMED ## AU: Search for updates [CallId = {0198DD3A-D7B0-48F5-A77D-795F8A1BDCE8}] 2012-04-10 22:47:16:097 956 718 AU # 1 updates detected 2012-04-10 22:47:16:097 956 718 AU ######### 2012-04-10 22:47:16:097 956 718 AU ## END ## AU: Search for updates [CallId = {0198DD3A-D7B0-48F5-A77D-795F8A1BDCE8}] 2012-04-10 22:47:16:097 956 718 AU ############# 2012-04-10 22:47:16:097 956 718 AU No featured updates notifications to show 2012-04-10 22:47:16:097 956 718 AU Setting AU scheduled install time to 2012-04-11 01:00:00 2012-04-10 22:47:16:097 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:47:16:097 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:47:16:113 956 55c AU Getting featured update notifications. fIncludeDismissed = true 2012-04-10 22:47:16:113 956 55c AU No featured updates available. 2012-04-10 22:47:18:780 956 bb8 Report REPORT EVENT: {27479C66-E930-4F9C-AFF2-27EDD76DED8F} 2012-04-10 22:47:13:773+0200 1 182 101 {B33ACEC1-3265-4D01-9C37-AC0892E95ED9} 100 80070643 AutomaticUpdates Failure Content Install Installation Failure: Windows failed to install the following update with error 0x80070643: Windows Internet Explorer 9 for Windows 7 for x64-based Systems. 2012-04-10 22:47:18:780 956 bb8 Report CWERReporter::HandleEvents - WER report upload completed with status 0x8 2012-04-10 22:47:18:780 956 bb8 Report WER Report sent: 7.5.7601.17514 0x80070643 B33ACEC1-3265-4D01-9C37-AC0892E95ED9 Install 101 Unmanaged 2012-04-10 22:47:18:780 956 bb8 Report CWERReporter finishing event handling. (00000000) WU-IE9-Windows7-x64.exe The actual update that is executed is downloaded and stored at the following location: C:\Windows\SoftwareDistribution\Download\Install\WU-IE9-Windows7-x64.exe Executing that file manually, results in the following error message: IE9_main.log The IE9 installer/updater also creates an own log file located at C:\Windows\IE9_main.log For the update session in question, the installer logged: 00:00.000: ==================================================================== 00:00.016: Started: 2012/04/10 (Y/M/D) 23:10:53.897 (local) 00:00.032: Time Format in this log: MM:ss.mmm (minutes:seconds.milliseconds) 00:00.063: Command line: "C:\Windows\SoftwareDistribution\Download\Install\WU-IE9-Windows7-x64.exe" 00:00.078: INFO: Setup installer for Internet Explorer: 9.0.8112.16421 00:00.094: INFO: Previous version of Internet Explorer: 9.0.8112.16443 00:00.110: INFO: Checking if iexplore.exe's current version is between 9.0.6001.0... 00:00.125: INFO: ...and 9.1.0.0... 00:00.141: INFO: Maximum version on which to run IEAK branding is: 9.1.0.0... 00:00.156: ERROR: A newer version of Internet Explorer is already installed on the system. 00:00.188: ERROR: Internet Explorer version check failed. 01:03.789: INFO: Setup exit code: 0x00009C48 (40008) - A more recent version of Internet Explorer is installed. 01:03.820: INFO: Scheduling upload to IE SQM server: http://sqm.microsoft.com/sqm/ie/sqmserver.dll 01:03.852: INFO: SQM Upload returned 403 01:03.867: INFO: Cleaning up temporary files in: C:\Windows\TEMP\IE978E.tmp 01:03.883: INFO: Unable to remove directory C:\Windows\TEMP\IE978E.tmp, marking for deletion on reboot. 01:03.898: INFO: Released Internet Explorer Installer Mutex Which pretty much confirms what the error message says when executing the update manually; it's simply already installed or even obsolete because a newer version is installed. So, why does it try to keep installing the update? Possible solutions? Uninstalling Windows Internet Explorer 9 and manually installing the cached C:\Windows\SoftwareDistribution\Download\Install\WU-IE9-Windows7-x64.exe will result in the same error after applying all pending updates. Applying the FixIt for the issue You receive “0x80070643” or “0x643” error codes when you try to install .NET Framework updates through Windows Update or Microsoft Updates will not resolve the issue. Applying the suggested solution for the issue Error message when you try to install updates by using the Windows Update or Microsoft Update Web site: "0x80070003" will not resolve the issue. Running the FixIt Automatically diagnose and fix common problems with Windows Update does report having resolved issues with Windows Update, but didn't resolve the issue. Running the FixIt for the issue How to troubleshoot Windows Update or Microsoft Update when you are repeatedly offered an update does not resolve the issue. Neither with normal nor with aggressive settings.

  Read the article

• Regarding traffic shaping on juniper SRX550

  - by peilin

  We have implemented the Juniper SRX550 in our company. Now we have one issue that how to restrict the internal user download speed from internet. Take one example that i want to restrict the end user with IP:192.168.1.20/32 downloading speed up to 1M via my external port ge-0/0/6.0. Below is my setting: [edit firewall policer p1M] root@SRX550# show if-exceeding { bandwidth-limit 1m; burst-size-limit 15k; } then discard; [edit firewall family inet] root@SRX550# show filter limit-user term 10 { from { destination-address { 192.168.1.20/32; } } then policer p1M; } term else { then accept; } [edit interfaces ge-0/0/6] root@SRX550# show per-unit-scheduler; unit 0 { family inet { filter { input limit-user; } address Hidden Here; } } As per the setting, the end user downloading speed should not exceed the 1m (125KB in windows), but the result is the downloading speed for this end users still can up to 400KB via HTTP/HTTPS. Please advise. Thanks.

  Read the article

• Exchange DiskShadow/Robocopy backup does not purge log files

  - by Robert Allan Hennigan Leahy

  I have a series of scripts setup to backup my Exchange. The following command is executed to start the process: diskshadow /s C:\Backup_Scripts\exchangeserverbackupscript1.dsh This is exchangeserverbackupscript1.dsh: #DiskShadow script file set verbose on #delete shadows all set context persistent writer verify {76fe1ac4-15f7-4bcd-987e-8e1acb462fb7} set metadata C:\Backup_Scripts\shadowmetadata.cab begin backup add volume C: alias SH1 create expose %SH1% P: exec C:\Backup_Scripts\exchangeserverbackupscript1.cmd end backup delete shadows exposed P: exit #End of script And this is exchangeserverbackupscript1.cmd: robocopy "P:\Program Files\Microsoft\Exchange Server\Mailbox\First Storage Group" "\\leahyfs\J$\E-Mail Backups\Day 1" /MIR /R:0 /W:0 /COPY:DT /B This is not causing Exchange to purge its log files. The edb file is 4.7 gigabytes, but the First Storage Group folder itself is 50+ gigabytes due to many, many log files for each day going back to 2009. Is there any way -- I've Googled and haven't found anything -- to notify Exchange when I've completed a full backup, and have it purge its log files? According to this and this, end backup should cause Exchange to "flush the transaction logs for that storage group" but only "if a successful backup of a storage group occurred", which leaves my question as: What constitutes a "successful backup", and why is what I'm doing not it?

  Read the article

• Firefox 3.6 and above. Always show one tab even if all tabs are closed like Firefox 3.0

  - by Jayapal Chandran

  I very much got used to Firefox 3.0. In that, to free the memory, I close all tabs but still the main Firefox window does not close. But in Firefox 3.6 and later if I want to close all tabs and if I do so then Firefox totally exists. This is not the case with 3.0. How to stop Firefox from not closing the main process even if I close all threads (tabs)? The autocomplete feature in the address bar of Firefox 3.6 and greater is in a dark blue color which makes me very much annoyed. With my environment and the monitor glare that is inducing anger in me, so how the color be changed to be like Firefox 3.0? Because you know that black and white are a neutral and good combination and since I have been working in Firefox 3.0 (and earlier versions) for a long time this new color change and other uncomfortable options are making me sick. To check CSS3 I need to use Firefox 3.5 and greater. Besides I like Firefox because it includes the W3C's recommendations so I can learn and test new recomendations from W3C.

  Read the article

• Kickstart CentOS 6 prompting for TCP/IP with network set to DHCP

  - by Andy Shinn

  I am trying to stop my kickstart CentOS install prompting me for TCP/IP information. After I click through this prompt (keeping IPv4 and IPv6 to their defaults) the installation continues and completes just fine. Below is my kickstart file: # Andy's super awesome VM kickstart file install url --url=http://mirrors.kernel.org/centos/6/os/x86_64 lang en_US.UTF-8 keyboard us text %include /tmp/network.ks rootpw --iscrypted $6$RA8DyrNTsVJkGIgY$ohZ62HHiOjNnn1yDMZlIu3lQ63D3plGPcbVZtPKE8Oq6Z.IGUgN.kNLkxs/ZymZuluRDWsW2eey5zLOl2G3mp. firewall --service=ssh authconfig --enableshadow --passalgo=sha512 selinux --disabled timezone America/Los_Angeles bootloader --location=mbr --driveorder=vda --append="crashkernel=auto rhgb quiet" # The following is the partition information you requested # Note that any partitions you deleted are not expressed # here so unless you clear all partitions first, this is # not guaranteed to work zerombr clearpart --all --drives=vda --initlabel part /boot --fstype=ext4 --size=500 part pv.253002 --grow --size=1 volgroup vg1 --pesize=4096 pv.253002 logvol / --fstype=ext4 --name=lv_root --vgname=vg1 --grow --size=1024 --maxsize=51200 logvol swap --name=lv_swap --vgname=vg1 --grow --size=4032 --maxsize=4032 repo --name="CentOS" --baseurl=http://mirrors.kernel.org/centos/6/os/x86_64 --cost=100 repo --name="Puppet Labs Products" --baseurl=http://yum.puppetlabs.com/el/6/products/x86_64 repo --name="Puppet Labs Dependencies" --baseurl=http://yum.puppetlabs.com/el/6/dependencies/x86_64 repo --name="EyeFi" --baseurl=http://flexo.eye.fi/6/eye-fi-api %packages @core @server-policy puppet facter %end %pre --erroronfail #!/bin/bash for x in `cat /proc/cmdline`; do case $x in SERVERNAME*) eval $x echo "network --onboot yes --device eth0 --bootproto dhcp --hostname ${SERVERNAME}.eye.fi" /tmp/network.ks ;; esac; done %end %post puppet agent --waitforcert 10 --onetime --no-daemon --pluginsync --server puppet.eye.fi %end reboot My kernel arguments are in this following virt-install command that I use to start the install: virt-install -n zabbix -r 2048 --vcpus=2 -l http://mirrors.kernel.org/centos/6/os/x86_64 --disk /dev/vg_inf1/zabbix --network bridge=br85 --initrd-inject=/home/ashinn/vm_kickstart --extra-args "ks=file:/vm_kickstart SERVERNAME=zabbix" --autostart During the install, I can pull up a console on the second terminal and verify the contents of /tmp/network.ks are: network --onboot=yes --bootproto=dhcp --ipv6=auto --hostname=jenkins2.mydomain.com Why might Anaconda be prompting for the TCP/IP settings when they are already set to DHCP?

  Read the article

• Campus VLAN Segmentation - By OS?

  - by Moduspwnens

  We've been thinking through re-arranging our network and VLAN configuration. Here's the situation. We already have our servers, VoIP phones, and printers on their own VLANs, but our problem lies with end user devices. There are just too many to lump on the same VLAN without being hammered with broadcasts! Our current segmentation strategy has them split into VLANs like this: Student iPads Staff iPads Student Macbooks Staff Macbooks Gaming devices Staff (Other) Student (Other) *Note that our network has many more iPads and MacBooks than most. Since the primary reason we're splitting them is just to put them in smaller groups, this has been working for us (for the most part). However, this required our staff to maintain access control lists (MAC addresses) of all devices belonging in these groups. It also has the unfortunate side effect of illogically grouping broadcast traffic. For example, using this setup, students on opposite ends of campus using iPads will share broadcasts, but two devices belonging to the same user (in the same room) will likely be on completely separate VLANs. I feel like there must be a better way of doing this. I've done a lot of research and I'm having trouble finding instances of this kind of segmentation being recommended. The feedback on the most relevant SO question seems to point toward VLAN segmentation by building/physical location. I feel like that makes sense because logically, at least among miscellaneous end users, broadcasts will typically be intended for nearby devices. Are there other campuses/large-scale networks out there segmenting VLANs based on end-system OS? Is this a typical configuration? Would VLAN segmentation based on physical location (or some other criteria) be more effective? EDIT: I've been told that we will soon be able to dynamically determine device OS without maintaining access lists, although I'm not sure how much that affects the answers to the questions.

  Read the article

• What is the IPv6 equivalent to IPv4 RFC1918 addresses?

  - by Kumba

  Having a hard time wrapping my head around IPv6 here. A lot of the lingo seems targeted at enterprise-level IPv6 deployments, discussing link-local, site-local, global unicast, scopes, etc. Not a lot of solid information on really small networks, like home networks. I want to check my thinking and make sure I am getting the correct translations from IPv4-speak to IPv6-speak. The first question is, what's the equivalent of RFC1918 for IPv6? Initial searches suggested there was no equivalent. Then I stumbled upon Unique Local Addresses (RFC4193), and that states that all ULA's should be assigned the prefix fc00, followed by a 40-bit random number in the routing prefix. This random number is to "prevent collisions when two IPv6 networks are interconnected" -- again, another reference to an enterprise-level function. If I have a small local LAN at home, numbered using 192.168.4.0/24, what's my equivalent in IPv6's ULA scope? Assuming I will never, ever, tie that IPv6 address into the real internet (a router will NAT & firewall it), can I ignore the RFC to an extent and go with fc00::4:0/120? It also seems that any address in fc00::/7 are to be globally routable. Does this mean I'll need extra protections so my router would not automatically start advertising these private IPv6 addresses to the world? Second question, what's this link-local thing? Reading suggests a default-assigned address in the fe80::/10 range that has the last 64bits of the address comprised of the interface's MAC address. Seems to be required, too, but I'm annoyed by the constant discussion of it in relation to enterprise networks. Third question, what is scope id for? Seems to be yet another term tossed around in relation to enterprise networks, especially when interconnecting them, but almost no explanation on the smaller home network level. Can I see a scope ID AND CIDR notation used together? I.e., fc00::4:0/120%6, or are scope IDs only supposed to be applied to a single /128 IPv6 address?

  Read the article

• What do the readonly attributes in diskpart really mean?

  - by marzipan

  I am wondering exactly what the meaning is of the "Read-only" disk and volume attributes that you can twiddle in diskpart on Windows 7. I am trying to set up an external USB drive as an installation medium for my own software, so I'd like to protect it against casual or inadvertent changes by users who it is given to, so they don't screw up the installation files they might need in the future. From what I can tell by experimentation with diskpart, the volume read-only attribute is actually stored on the physical disk somewhere, because I can set it and it shows up when I take the drive to another machine. This is great because my users can't (easily) change any of the files on the volume, or format it from Windows explorer. However, the disk read-only attribute seems to be just an aspect of how the current machine is accessing the drive. When I set it I can no longer delete the volume in the disk via Disk Management, but when I take the drive to another machine, the attribute is no longer set and in Disk Management I can delete the volume on the disk. I guess I'm not that worried about my users doing that, but I am annoyed that I don't understand what these attributes are really doing. Another thing that I don't understand is that the "volume" read-only attribute actually seems to be global to the disk - if I have two volumes on the disk, and I set the readonly flag on one of them, then it gets set on the other one too. ?!? I have the feeling I'm not searching for the right docs - all I'm finding is diskpart docs that give the syntax for twiddling these attributes, not what they really mean. Any pointers would be very welcome! Thanks, Asa

  Read the article

• Proper way to use hiera with puppetlabs-spec-helper?

  - by Lee Lowder

  I am trying to write some rspec tests for my modules. Most of them now use hiera. I have a .fixures.yml: fixtures: repositories: stdlib: https://github.com/puppetlabs/puppetlabs-stdlib.git hiera-puppet: https://github.com/puppetlabs/hiera-puppet.git symlinks: mongodb: "#{source_dir}" and a spec/classes/mongodb_spec.rb: require 'spec_helper' describe 'mongodb', :type => 'class' do context "On an Ubuntu install, admin and single user" do let :facts do { :osfamily => 'Debian', :operatingsystem => 'Ubuntu', :operatingsystemrelease => '12.04' } end it { should contain_user('XXXX').with( { 'uid' => '***' } ) should contain_group('XXXX').with( { 'gid' => '***' } ) should contain_package('mongodb').with( { 'name' => 'mongodb' } ) should contain_service('mongodb').with( { 'name' => 'mongodb' } ) } end end but when I run the spec test, I get: # rake spec /usr/bin/ruby1.8 -S rspec spec/classes/mongodb_spec.rb --color F Failures: 1) mongodb On an Ubuntu install, admin and single user Failure/Error: should contain_user('XXXX').with( { 'uid' => '***' } ) LoadError: no such file to load -- hiera_puppet # ./spec/fixtures/modules/hiera-puppet/lib/puppet/parser/functions/hiera.rb:3:in `function_hiera' # ./spec/classes/mongodb_spec.rb:15 Finished in 0.05415 seconds 1 example, 1 failure Failed examples: rspec ./spec/classes/mongodb_spec.rb:14 # mongodb On an Ubuntu install, admin and single user rake aborted! /usr/bin/ruby1.8 -S rspec spec/classes/mongodb_spec.rb --color failed Tasks: TOP => spec_standalone (See full trace by running task with --trace) Module spec testing is relatively new, as is hiera. So far I have been unable to find any suitable solutions. (the back and forth on puppet-dev was interesting, but not helpful). What changes do I need to make to get this to work? Installing puppet from a gem and hacking on rubylib isn't a viable solution due to corporate policy. I am using Ubuntu 12.04 LTS + Puppet 2.7.17 + hiera 0.3.0.

  Read the article

• Why is my mono/XSP site loading slow?

  - by acidzombie24

  I have two sites on the same server. One is loading perfectly and incredibly fast. The other is an equally complex site except a bit less javascript and 0 images. Its taking several seconds to load and there is a 1 in 3 chance that i get a Http500 error. WTF I grabbed the lastest 2.6.? version of mono, mod_mono and xsp (libgdiplus-2.6.7, xsp-2.6.5, mod_mono-2.6.3 and mono 2.6.7) This is whats in apache error.log [Mon Jan 03 19:33:40 2011] [error] (70014)End of file found: read_data failed [Mon Jan 03 19:33:40 2011] [error] Command stream corrupted, last command was 1 [Mon Jan 03 19:34:52 2011] [error] (70014)End of file found: read_data failed [Mon Jan 03 19:34:52 2011] [error] (70014)End of file found: read_data failed [Mon Jan 03 19:34:52 2011] [error] Command stream corrupted, last command was 1 [Mon Jan 03 19:34:52 2011] [error] Command stream corrupted, last command was 1 this is the page error Internal Server Error The server encountered an internal error or misconfiguration and was unable to complete your request. Please contact the server administrator, webmaster@localhost and inform them of the time the error occurred, and anything you might have done that may have caused the error. More information about this error may be available in the server error log. Apache/2.2.9 (Debian) PHP/5.2.6-1+lenny9 with Suhosin-Patch mod_mono/2.6.3 Server

  Read the article

• Disk Partitioning problem with fdisk.

  - by MA1

  Currently i am using fdisk to create/resize windows partitions. Following is a sample input script to fdisk to create/resize windows partitions: fdisk /dev/sda < partInput the contents of partInput are as follows: d #delete the partition 3 #partition number to be deleted n #add a new partition p #primary: type of new partition 3 #new partition number 18804 #start cylinder of new partition 77433 #end cylinder of new partition t #change the type of partition 3 #partition number whose type(filesystem) is to be changed 7 #HPFS/NTFS: partition type(filesystem) n #add a new partition p #primary: type of partition 77434 #first cylinder of new partition 77825 #end cylinder new partition w #write all the above changes As you see in the above input we are using cylinders for start and end. Earlier i am using sectors as unit and everything is working fine but getting problems when partitioning a 1.5TB hard drive. Then i changed the unit to cylinders but it is working on some machines not all. On some machines fdisk failed to create the partition table correctly. So, i am thinking to move to parted if there is no way to do the above using fdisk. Please also tell me how to correctly convert sectors to cylinders? How to perform all the above steps using parted without losing the data OR how to use fdisk correctly?

  Read the article

• New Static Website with Hosted DNS alternating 502, 503 and Page Does Not Exist Errors

  - by Dave

  This has become an increasingly frustrating ordeal. I'm mostly a web developer, so forgive me if I am using improper terminology here. I have a client that had purchased a domain at JustHost. We built him a website and have it on our own server space. Now, I'm mostly used to dealing with godaddy and it is simple enough to manage dns records and point the A record to our server IP, where Apache on our end deals with the domains via name-based virtual hosts. But for some reason, in setting this up with JustHost, when attempting to go to the domain name, I either get a 502 or 503 error or "webpage does not exist". Now, I know that the basic functionality of the webpage must be working because I can access the the index etc straight through my servers www data (IE [server-ip]/website_folder). I was on the phone with technical support for over three hours yesterday with justhost and the best I could get was "That's really weird..." I've checked my logs and there doesn't seem to be anything coming through to my end. Does anybody have an idea of whats going on here? I would love for it to be a problem on my end, because justhost doesn't seem capable of helping further. Any help is greatly appreciated, thanks. I forgot to mention that we have several other sites up and running and completely accessible.

  Read the article

• how could application installations/configurations be easier in linux?

  - by ajsie

  although you can do anything in linux it tends to require a lot of tweaking in config files and reading a lot of manuals/tutorials before you can have it running in your way. i know that it gets a lot easier by time, and the apt-get installations with ubuntu/debian is heading the right way. but how can linux be more userfriendly for us in the future? i thought that if more is automated like an IDE environment, eg. typing svn will give us all the commands and description about each command when you move between commands with your keyboard. that would be great. but that's just one example. another is the navigation in the terminal between folders. now you have to type a lot just to jump from/to different folders. would be great with some more automatization here too. i know that these extra features will slow down the server, but its 2010 now, and these features are not that heavy for the cpu, but makes it more userfriendly and encourage maintainance of a server, not frighten u off. what do you think about this? should/could we have more user friendly linux environment in servers, something that has annoyed you a lot? a lot of things are done in the unix way, but maybe we should reinvent the wheel in some areas, cause apparently, its so...repeatingly today and difficult to do easy tasks. it should be easier i think..

  Read the article

• Juniper SSG 5 VPN

  - by Ethabelle

  I have a host who set up our Juniper SSG 5 VPN with Firmware version-6.2.0r5.0 I've been trying to set up VPN on it using this guide: http://kb.juniper.net/InfoCenter/index?page=content&id=KB4094 I've followed the steps and on my Mac, whenever I try to connect using L2TP over IPSec I get the following error; Summary of Steps: Create User (give them L2TP auth ability), Create Group, Place User in Group, Create VPN Gateway, Create VPN, create IP Pool, change default L2TP settings, create Untrust Trust Policy. The L2TP-VPN server did not respond. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I looked in my Firewall's logs, but I don't even see anything under Reports Logs Events. I'm.. obviously missing something, I just don't know what I'm missing at this point. I'm just starting networking and this is sort of Step 101 and I'm getting annoyed and just want to throw up OpenVPN, but I've read that has problems with Juniper Firewalls. Hooray.

  Read the article

• Vim - Displaying Code Output in a New Window á la Textmate?

  - by Michael Density

  A few months back I switched from Textmate to Vim. Overall I really love Vim, but one of the things I miss from Textmate is using the ⌘R command to run Ruby code and having the results neatly pop up in a new, scrollable window. Obviously, Vim is capable of running Ruby code and displaying the output with :w !ruby. The only downside to this is that if the resulting output is too long I can't scroll through it. To combat this problem I tried modifying a :redir function from Vim Tips. It looks like this: function! TabNew(cmd) redir => message silent execute a:cmd redir END tabnew silent put=message set nomodified endfunction command! -nargs=+ -complete=command TabNew call TabNew(<q-args>) Now the output from Ruby is put into a new tab. However, I can't get it to pop up in a new, separate window. Changing tabnew to new just sends the output to a split in the same window. The other problem is that a visible ^M gets appended to the end of each line, so the output ends up looking like this, which is kind of bothersome: Hello World!^M So, is there any way to get the output into a separate window without the ^M appended to the end? Are there any plugins I should be trying to achieve this Textmate-like effect for code output?

  Read the article

• Bouncing between a 502 and 503 error

  - by Dave

  This has become an increasingly frustrating ordeal. I'm mostly a web developer, so forgive me if I am using improper terminology here. I have a client that had purchased a domain at JustHost. We built him a website and have it on our own server space. Now, I'm mostly used to dealing with godaddy and it is simple enough to manage dns records and point the A record to our server IP, where Apache on our end deals with the domains via name-based virtual hosts. But for some reason, in setting this up with JustHost, when attempting to go to the domain name, I either get a 502 or 503 error or "webpage does not exist". Now, I know that the basic functionality of the webpage must be working because I can access the the index etc straight through my servers www data (IE [server-ip]/website_folder). I was on the phone with technical support for over three hours yesterday with justhost and the best I could get was "That's really weird..." I've checked my logs and there doesn't seem to be anything coming through to my end. Does anybody have an idea of whats going on here? I would love for it to be a problem on my end, because justhost doesn't seem capable of helping further. Any help is greatly appreciated, thanks. I forgot to mention that we have several other sites up and running and completely accessible.

  Read the article

• why altgr+p doesn't work, AUTOHOTKEY

  - by voodoomsr

  Hi guys, i try and i try to find the bug in this script but i can't . Maybe some of you can give me a hint... Problem. When i press altgr&p it suppose that the Delete key is triggered, but the weird thing is that after one succesfull delete, if i continue pressing altgr&p appears the p, and the delete isn't triggered anymore. in the meantime i test other solution move to the right and then delete with the backspace, that works, but when i have text selected this alternative isn't good.... here is the code #InstallKeybdHook ;characters very used RAlt & e:: SendInput []{Left} Return RAlt & w:: SendInput <>{Left} Return RAlt & d:: SendInput (){Left} Return RAlt & s:: SendRaw {} SendInput {Left} Return RAlt & x:: SendInput ""{Left} Return RAlt & c:: SendInput ''{Left} Return RAlt & f:: SendInput * Return RAlt & r:: SendRaw + Return RAlt & v:: SendInput - Return ;comienzo y fin de linea RAlt & a:: SendInput {Home} Return RAlt & z:: SendInput {End} Return ;movimientos InEditon /* RAlt & p:: SendInput {Right}{BackSpace} Return */ <^>!p:: Send {Del} Return RAlt & o:: SendInput {Up} Return RAlt & l:: SendInput {Down} Return RAlt & k:: SendInput {Left} Return RAlt & ñ:: SendInput {Right} Return RAlt & ,:: SendInput {Enter} Return RAlt & i:: SendInput {BackSpace} Return ;; clipx ^mbutton:: sendinput ^+{insert} Return ^+k::^+Left +k::+Left ^k::Left +l::+Down ^+l::^+Down ^l::^Down +ñ::+Right ^+ñ::^+Right ^ñ::^Right +o::+Up ^+o::^+Up ^o::^Up +a::+Home ^+a::^+Home +z::+End ^+z::^+End

  Read the article

• Upstart can't determine my process' pid

  - by sirlark

  I'm writing an upstart script for a small service I've written for my colleagues. My upstart job can start the service, but when it does it only outputs queryqueue start/running; note the lack of a pid as given for other services. #/etc/init/queryqueue.conf description "Query Queue Daemon" author "---" start on started mysql stop on stopping mysql expect fork env DEFAULTFILE=/etc/default/queryqueue umask 007 kill timeout 30 pre-start script #if [ -f "$DEFAULTFILE" ]; then # . "$DEFAULTFILE" #fi [ ! -f /var/run/queryqueue.sock ] || rm -rf /var/run/queryqueue.sock #exec /usr/local/sbin/queryqueue -s /var/run/queryqueue.sock -d -l /tmp/upstart.log -p $PIDFILE -n $NUM_WORKERS $CLEANCACHE $FLUSHCACHE $CACHECONN end script script #Originally this stanza didn't exist at all if [ -f "$DEFAULTFILE" ]; then . "$DEFAULTFILE" fi exec /usr/local/sbin/queryqueue -s /var/run/queryqueue.sock -d -l /tmp/upstart.log -p $PIDFILE -n $NUM_WORKERS $CLEANCACHE $FLUSHCACHE $CACHECONN end script post-start script for i in `seq 1 5` ; do [ -S /var/run/queryqueue.sock ] && exit 0 sleep 1 done exit 1 end script The service in question is a python script, which when run without error, forks using the code below right after checking command line options and basic environmental sanity, so I tell upstart to expect fork. pid = os.fork() if pid != 0: sys.exit(0) The script is executable, and has a python shebang. I can send the TERM signal to the process manually, and it quits gracefully. But running stop queryqueue claims queryqueue stop/waiting but the process is still alive and well. Also, it's logs indicate it never received the kill signal. I'm guessing this is because upstart doesn't know which pid it has. I've also tried expect daemon and leaving the expect clause out entirely, but there's no change in behaviour. How can I get upstart to determine the pid of the exec'd process

  Read the article

• How to get rid of Windows XP Pro Blue pop up screen

  - by LISA

  Windows XP user-home edition 36 bit. One day I woke to see a blue pop up screen from Microsoft Windows XP Pro. I have not installed anything new myself. The 'add on' pop up always comes on when I open up mozilla to surf the net. I always just close it out to not install anything. I then woke to have colored tabs, the new download status bar at the bottom and this pop up window that asks me to retype two words spaced, a timer of two minutes starts and states if no word put in system will shut off. I have let it run down more than a few times and it does not shut down. No other options to choose from. If I misspell with a lot of letters it tells me I did so, but if I can't read a few letters I guess at it although it is not and it lets me resume what I am doing. This window pops up every single minute no matter what I am doing. Please help, I'm really annoyed with this. I have searched the net all over and don't quit know what to look for anymore

  Read the article

• Why does my Intel Tolapai network chip not transmit packets?

  - by Hanno Fietz

  I'm trying to deploy an embedded system (NISE 110 by Nexcom) based on the Intel EP80579 (Tolapai) chip. Tolapai apparently integrates controllers for Ethernet etc. on a single chip (Intel homepage). The machine can't get a network connection. Diagnosis as far as I could manage: Drivers drivers from Intel compiled and installed without problems (version 1.0.3-144). Kernel version and Linux distribution (CentOS 5.2, 2.6.18) match the driver's installation instructions. drivers are loaded and show up in lsmod (module names are gcu and iegbe) interfaces eth0 and eth1 show up in ifconfig ifconfig I can bring up the interfaces with fixed IP pinging the interface locally works ifconfig shows flag UP but not RUNNING Link ethtool shows "Link detected: no", "Speed: unknown (65536)" and "Duplex: unknown (255)" Link LED is on on the other side of the cable, ethtool shows "Link detected: yes" and reports a speed of 1000 Mbps, which has allegedly been auto-neogotiated with the problematic device. Network traffic analysis the device does not reply on ARP, ICMP echo or anything else (iptables is down) when trying to send ICMP or DHCP requests, they never reach the other end activity LED is off on the device, on at the other end. I tried the following without any effect: Different cables (2 straight, one crossed), I get the link LED lit up on each. Three different devices on the other end (one PC, one netbook, one router) Fixed ARP table entries on both sides Connecting both network ports of the machine with each other, won't ping through the cable, but will ping locally. Tried straight and crossed cables for that.

  Read the article

• Getting Win32_Service security descriptor using VBScript

  - by invictus

  Hi, I am using VbScript for retrieving the securitydescriptor of a Win32_Service. I am using the following code: SE_DACL_PRESENT = &h4 ACCESS_ALLOWED_ACE_TYPE = &h0 ACCESS_DENIED_ACE_TYPE = &h1 strComputer = "." Set objWMIService = GetObject("winmgmts:" _ & "{impersonationLevel=impersonate, (Security)}!\\" & strComputer & "\root\cimv2") Set colInstalledPrinters = objWMIService.ExecQuery _ ("Select * from Win32_Service") For Each objPrinter in colInstalledPrinters Wscript.Echo "Name: " & objPrinter.Name ' Get security descriptor for printer Return = objPrinter.GetSecurityDescriptor( objSD ) If ( return <> 0 ) Then WScript.Echo "Could not get security descriptor: " & Return wscript.Quit Return End If ' Extract the security descriptor flags intControlFlags = objSD.ControlFlags If intControlFlags AND SE_DACL_PRESENT Then ' Get the ACE entries from security descriptor colACEs = objSD.DACL For Each objACE in colACEs ' Get all the trustees and determine which have access to printer WScript.Echo objACE.Trustee.Domain & "\" & objACE.Trustee.Name If objACE.AceType = ACCESS_ALLOWED_ACE_TYPE Then WScript.Echo vbTab & "User has access to printer" ElseIf objACE.AceType = ACCESS_DENIED_ACE_TYPE Then WScript.Echo vbTab & "User does not have access to the printer" End If Next Else WScript.Echo "No DACL found in security descriptor" End If Next However, every time I run it I get the message saying the resulting code is -2165236532 something, rather than the error codes defined in the manual. Anyone got any ideas? I am using Windows 7 professional.

  Read the article

• Install Exchange 2013 with DSC

  - by Alain Laventure

  I tried to install Exchange 2013 with the resource windowsProcess in existing Exchange Configuration. All prerequisites are installed (the Exchange Organization still exists). This is my Resource section: WindowsProcess Exchange2013 { Credential=$credential Path= "C:\Sources\Cumulative Update 5 for Exchange Server 2013 (KB2936880)\Setup.exe" Arguments= "/mode:Install /role:Mailbox /IAcceptExchangeServerLicenseTerms /TargetDir:C:\EX2013" Ensure= "Present" } #End Filter } #End Node } # End configuration /* @TargetNode='TargetDSC02' @GeneratedBy=exadmin @GenerationDate=08/02/2014 08:16:03 @GenerationHost=SOURCEDSC02 */ instance of MSFT_Credential as $MSFT_Credential1ref { Password = "Password1"; UserName = "S05\\Exadmin"; }; Exadmin is a member of Orgaganization Management Group and it is also member of Domain Admin Group, to be able to install Exchange When I execute this resource , Exchange Installation Start but after 1 minute the installation stops with this error: Failed [Rule:GlobalServerInstall] [Message:You must be a member of the 'Organization Management' role group or a member of the 'Enterprise Admins' group to continue.] To be sure that the right is really the problem I create a special User with only Administrator right of the Exchange server and with no Exchange Permission I run manually on the new Exchange server .\Setup.exe /mode:Install /role:Mailbox /IAcceptExchangeServerLicenseTerms /Targetdir:C:\EX2013 And I got the Same error that with DSC. After I add my test user in the Organization Management Group and I run again manually .\Setup.exe /mode:Install /role:Mailbox /IAcceptExchangeServerLicenseTerms /Targetdir:C:\EX2013 And the Exchange 2013 installation finish without any error. That prove that the problem with DSC is Permission right.

  Read the article

• Move every 3 rows into a column in excel

  - by Eliane El Asmr

  Please i need your help. I need to move every 3 rows into a new colomn. --Let's suppose i have this: Ambassade de France S.E. M. Patrice PAOLI 01-420000-420150 Ambassade de France Mme. Jamilé Anan 01-420000-420150 Ambassade de France Mme . Marie Maamari 01-420000-420150 --I need them to be Like this: Ambassade de France S.E. M. Patrice PAOLI 01-420000-420150 Ambassade de France Mme. Jamilé Anan 01-420000-420150 Ambassade de France Mme . Marie Maamari 01-420000-420150 I have this code. Can you help me Please. It's giving me error. Out of range. What should i change? It's urgent:(the code is for every 7, i need for every 3) Sub Every7() Dim i As Integer, j As Integer, cl As Range Dim myarray(100, 6) As Integer 'I don't know what your data is. Mine is integer data 'Change 100 to however many rows you have in your original data, divided by seven, round up 'remember arrays start at zero, so 6 really is 7 If MsgBox("Is your entire data selected?", vbYesNo, "Data selected?") <> vbYes Then MsgBox ("First select all your data") End If 'Read data into array For Each cl In Selection.Cells Debug.Print cl.Value myarray(i, j) = cl.Value If j = 6 Then i = i + 1 j = 0 Else j = j + 1 End If Next 'Now paste the array for your data into a new worksheet Worksheets.Add Range(Cells(1, 1), Cells(101, 7)) = myarray End Sub Thank you.

  Read the article

< Previous Page | 178 179 180 181 182 183 184 185 186 187 188 189  | Next Page >