Search Results

Search found 5619 results on 225 pages for 'starts'.

Page 196/225 | < Previous Page | 192 193 194 195 196 197 198 199 200 201 202 203  | Next Page >

  • Two DHCP Servers, Block Clients for one of them?

    - by Rilindo
    I am building out a kickstart network that resides on a different VLAN uses its own DHCP server. For some reason, my kickstart clients kept getting assign IPs from my primary DHCP server. The way I have it set up is that I have a primary DHCP server on this router here: 192.168.15.1 Connected to that DHCP server is a switch with the IP of 192.168.15.2. My kickstart (Scientific Linux) server is connected to that switch on two ports: Port 2 - where the kickstart server communicates to the rest of the production network via eth0. The IP assigned to the server on that interface is 192.168.15.100 (on eth0). The details are: Interface: eth0 IP: 192.168.15.100 Netmask: 255.255.255.0 Gateway: 192.168.15.1 Port 7 - has it's own VLAN ID (along with port 8). The kickstart server is connected to that port with the IP of 172.16.15.100 (on eth1). Again, the details are: Interface: eth1 IP: 172.16.15.100 Netmask: 255.255.255.0 Gateway: none The kickstart server runs its own DHCP server and assigns them over the eth1. Most of the kick starts are built over the kickstart VLAN through port 8. To prevent the kickstart DHCP server from assigning addresses over the production network, I have the route setup like so: route add -host 255.255.255.255 dev eth1 At this point, the clients kept getting assign IPs from the 192.168.15.1 DHCP server. I need to figure out a way to block client requests from reaching that DHCP. Its should be noted that but I also build KVM hosts on the kickstart server as well, so I need those KVMs to have the ability to get DHCP requests from the 192.168.15.1 DHCP server via the bridge network once I finish resolved this particular problem. (Currently, they communicate via NAT). So what would be done to resolve this? Through iptables or some sort of routing I need to put in? I tried to limited to requests via IPtables on that interface, allowing DHCP requests for 172.16.15.x network: -A INPUT -i eth1 -s 172.16.15.0/24 -p udp -m udp --dport 69 -j ACCEPT -A INPUT -i eth1 -s 172.16.15.0/24 -p tcp -m tcp --dport 69 -j ACCEPT -A INPUT -i eth1 -s 172.16.15.0/24 -p udp -m udp --dport 68 -j ACCEPT -A INPUT -i eth1 -s 172.16.15.0/24 -p tcp -m tcp --dport 68 -j ACCEPT -A INPUT -i eth1 -s 172.16.15.0/24 -p udp -m udp --dport 67 -j ACCEPT -A INPUT -i eth1 -s 172.16.15.0/24 -p tcp -m tcp --dport 67 -j ACCEPT And rejects assignments on eth1 from 192.168.15.x network: -A FORWARD -o eth1 -s 192.168.15.0/24 -p udp -m udp --dport 69 -j REJECT -A FORWARD -o eth1 -s 192.168.15.0/24 -p tcp -m tcp --dport 69 -j REJECT -A FORWARD -o eth1 -s 192.168.15.0/24 -p udp -m udp --dport 68 -j REJECT -A FORWARD -o eth1 -s 192.168.15.0/24 -p tcp -m tcp --dport 68 -j REJECT -A FORWARD -o eth1 -s 192.168.15.0/24 -p udp -m udp --dport 67 -j REJECT -A FORWARD -o eth1 -s 192.168.15.0/24 -p tcp -m tcp --dport 67 -j REJECT Nope. :(

    Read the article

  • Cannot access boot menu with compaq 8510p

    - by pinouchon
    I have a problem with my HP compaq 8510p laptop: when I start it, the fan starts and the power light is on, but the screen displays nothing. When I insert a bootable hard drive, it activates the hard drive light (meaning that the CD is recognized) but it stops after a few seconds. Same thing with any hard drive: the drive is recognized but does not boot. What I've tried so far: Changing the hard drive or booting with no hard drive (same problem) Plugging anoher display via VGA : no display on the other screen Inserting a windows-7 CD (same problem) Booting only on battery, with battery and power cable, only with power cable (same problem) So it looks like something is preventing the laptop from booting and displaying the boot menu. Do you have experienced something similar with a laptop ? What could be wrong ? The laptop is out of warranty. The system used to be windows-7 x64. Edit: I went to the help desk of my university. A guy took a look (he also tried to plug an external screen) and said that the computer is dead: on the HP laptops eventually the GPU card dies and so does the motherboard because they are linked. He saw this many times, and even if I can fix the problem, the laptop would crash again after a while. Do you have similar experience with HP laptops ? (mine is 4 years old) Edit 2: Believe it or not, my laptop is magically working again. I have no clue about what is going on. Now it is like starting and old car: when you turn it on you secretly hope it will actually start... With that said, I expect my laptop to break again in the near future (its an HP after all) and I will accept an answer or add my own accordingly. Edit 3: As expected, the laptop is down again. This time, sometimes when I power it up, it shuts down automatically after 3 seconds, sometimes not at all. In addition, when it does not shut down on its own, the power button does not work : the only way to shut it down is by unplugging the battery. As before, the screen is black, and only the power and battery lights are on. (the other ones: hard drive and wifi are off). I have tried to plug in another power plug, removing the battery and removing the hard drive without success. I might buy another laptop. I've brought the laptop to a repair shop. The problem is indeed that the graphic card is down. It will be replaced by a new one.

    Read the article

  • Apache's htcacheclean doesn't scale: How to tame a huge Apache disk_cache?

    - by flight
    We have an Apache setup with a huge disk_cache (500.000 entries, 50 GB disk space used). The cache grows by 16 GB every day. My problem is that the cache seems to be growing nearly as fast as it's possible to remove files and directories from the cache filesystem! The cache partition is an ext3 filesystem (100GB, "-t news") on an iSCSI storage. The Apache server (which acts as a caching proxy) is a VM. The disk_cache is configured with CacheDirLevels=2 and CacheDirLength=1, and includes variants. A typical file path is "/htcache/B/x/i_iGfmmHhxJRheg8NHcQ.header.vary/A/W/oGX3MAV3q0bWl30YmA_A.header". When I try to call htcacheclean to tame the cache (non-daemon mode, "htcacheclean-t -p/htcache -l15G"), IOwait is going through the roof for several hours. Without any visible action. Only after hours, htcacheclean starts to delete files from the cache partition, which takes a couple more hours. (A similar problem was brought up in the Apache mailing list in 2009, without a solution: http://www.mail-archive.com/[email protected]/msg42683.html) The high IOwait leads to problems with the stability of the web server (the bridge to the Tomcat backend server sometimes stalls). I came up with my own prune script, which removes files and directories from random subdirectories of the cache. Only to find that the deletion rate of the script is just slightly higher than the cache growth rate. The script takes ~10 seconds to read the a subdirectory (e.g. /htcache/B/x) and frees some 5 MB of disk space. In this 10 seconds, the cache has grown by another 2 MB. As with htcacheclean, IOwait goes up to 25% when running the prune script continuously. Any idea? Is this a problem specific to the (rather slow) iSCSI storage? Should I choose a different file system for a huge disk_cache? ext2? ext4? Are there any kernel parameter optimizations for this kind of scenario? (I already tried the deadline scheduler and a smaller read_ahead_kb, without effect).

    Read the article

  • How to auto advance a PowerPoint slide after an exit animation is over?

    - by joooc
    PowerPoint entrance animation set up with "Start: With Previous" starts right when a new slide is advanced. However, if you set up an exit animation in the same way, it doesn't start with a slide ending sequence. Instead, the "Start: On Click" trigger needs to be used and after your exit animation is over you still need one extra click just to advance to the next slide. Workarounds to this are obvious: create a duplicate slide, make your ending animations from the original slide being your starting animations on the duplicate slide and let them be followed with whatever you want or create a transition slide with those ending animations only and set up "Change Advance slide - Automatically after - [the time it takes your animations to finish]". These workarounds will make it work for your audience, visually. However, it has an impact on slide numbers you might need to adjust accordingly and/or duplicate content changes. If you are the only one creating and using your presentation, this might be just fine. But if you are creating a presentation in collaborative mode with three other people and don't even know who will be the presenter at the end, you can mess things up. Let's be specific: most of my slides have 0.2s fly in entrance animation applied to blocks of content coming from right, bottom or left. Advancing to the next slide I want them to fly out in another 0.2s exit animation being followed by new slide 0.2s fly in entrance animation of the new blocks. The swapping of the blocks should be triggered while advancing to the next slide, as usually. As mentioned, I'm not able to achieve this without one extra click between the slides. I wrote a VBA script that should start together with an exit animation and will auto advance a slide after 0.3s when the exit animation is over. That way I should get rid of those extra clicks which are needed right now. Sub nextslide() iTime = 0.3 Start = Timer While Timer < Start + iTime DoEvents Wend With SlideShowWindows(1).View .GotoSlide (ActivePresentation.SlideShowWindow.View.Slide.SlideIndex + 1) End With End Sub It works well when binded on a box, button or another object. But I can't make it run on a single click (anywhere on the slide) so that it could start together with the exit animation onclick trigger. Creating a big transparent rectangular shape over the whole slide and binding the macro on it doesn't help either. By clicking it you only get the macro running, exit animation is not triggered. Anyway, I don't want to bind the macro to any other workaround object but the slide itself. Anyone knows how to trigger a PowerPoint VBA script on slide onclick event? Anyone knows a secret setting that will make the exit animation work as expected i.e. animating right before exiting a slide while transitioning to the next one? Anyone knows how to beat this dragon? Thank you!

    Read the article

  • windows 7 virtual wireless adapter keeps going to sleep

    - by conners
    Just a quick question that I can't see mentioned anywhere online. I have a Windows 7 box configured like these guys recommend http://www.itgeekdiary.com/windows-7-as-an-wi-fi-access-point/ simply so that I can have my Windows 7 box as a wifi access point or a wifi emitter. It's also called a Microsoft Virtual WiFi Miniport Adapter. But it powers off and shuts down automatically and stops working. Basically everything works as intended and then - well -it will stopped working when I am not at the Windows 7 PC for a long time. The problem seems to be that every time my PC goes to "power save / sleep" and in the morning the Windows 7 machine "wakes" but blooming heck the wifi has stopped and you have to power cycle the PC (which is very uncool). When I power Cycle I have to do the following as administrator C:\Windows\System32\netsh.exe wlan start hostednetwork I then tried a gazllion things involving services and power management and eventually discovered that if I run the following commands as administrator it will be ok (for a bit) but every 3rd ot 4th time I try this "trick" it simply fails. the trick that seems to work 3 out of 4 times (i.e. "most" of the time) C:\Windows\System32\netsh.exe wlan stop hostednetwork C:\Windows\System32\netsh.exe wlan start hostednetwork But why does this only work "some" of the time? What else I did by myself: on every manage adapter properties (that relates to the wifi) I right clicked [configure] [power management] /disabled/ "allow the computer to power off to save power" <- this made no difference Also (and this is a bit annoying) there is no system tray app/GUI for the Microsoft Virtual WiFi Miniport Adapter output signal ... none... so (lame as it sounds) the ONLY way I can check if it's on is to physically go to another device and SCAN.. lame so my question can probably be solved by any of the following: a) can I stop Windows 7 sleeping this wifi when the machine sleeps b) can I force Windows to force wake this process on wake? if so how? c) what is the service / process REALLY called and how do I restart it if it crashes d) how can I flush the wifi properly rather power cycle the host machine e) anyone have a link to an program or app that can sit in the system tray that shows windows 7 wifi hotspot emission status (on/off/etc etc) Since I am a programmer I can easily write a vbs script / windows exe to fix this (and I will share this solution) and the gui problem if I can work out the actual service that is running that netsh stops/starts

    Read the article

  • Why Photoshop CS5's photomerge's result immediately disappear?

    - by koiyu
    I have a bunch of JPG-files which I want to stitch together with Photoshop's Photomerge function. I choose File → Automate → Photomerge... and browse for the files. Photoshop opens the files and starts analyzing. I see the process bar filling and different phases are mentioned on the process bar. Nothing weird there. When the merging is done (and if I don't blink my eyes), I can see layers-palette is populated with the chosen files and, by quickly judging from the layer thumbnails, they're properly aligned. Sometimes the image window itself can be seen, but not always. Problem is that the layers and the image disappear in a flash. There is no error message. Everything is like prior starting the photomerge. No file has been changed. I could continue to use Photoshop normally. This is what I've tried so far: Loaded folder which has 38 JPG images, 4272 x 2848 and ˜ 5 megabytes per file Loaded the same files, but chose Use Files instead of Use Folder in the photomerge's window Loaded 19 JPG images, 4272 x 2848 and ˜ 5 megabytes per file Loaded 10 JPG images, ⇑ see above Loaded 5 JPG images, see above Loaded 3 JPG images, see above Scaled the images to 2256 x 1504 and ˜< 1 megabytes per file Loaded in a set of 38, 19, 10, 5, 3 Following steps are tested with these smaller files and with a set of 5 images Read Adobe's forums and reduced the amount of RAM Photoshop uses gradually from ˜ 80 % to 50 % (though I didn't understand the logic behind this) Would've reduced cache tile size to 128K, but it was set so already Disabled OpenGL Scaled the images to 800 x 533 and ˜ 100 kilobytes per file, loaded a set of 5 Read more unanswered threads around the internet In between each test I closed and reopened Photoshop. This is the first time I've even tried using photomerge. Am I doing something wrong? How can I locate what is the problem? How do I fix this? Photoshop is 64 bit Extended CS5 version. I'm on a mid-2010 quad-core (i5) iMac with up-to-date Mac OS X 10.6.6. Edit: Weird. First loading the images into one file via File → Scripts → Load Files into Stack… and then using Edit → Auto-Align Layers…, which, effectively, is the same as photomerge (even the dialog looks kind of the same), works! Even with the original JPGs without any issues. This doesn't fix photomerge, though.

    Read the article

  • Windows 7 immediately disconnects a USB drive

    - by Daniel Saner
    I am having a problem with Windows 7 x64 consistently disconnecting one specific USB mass storage drive immediately after it is connected. The drive in question is a Cowon C2 digital music player which works in standard mass storage controller mode (i.e. no device-specific drivers needed/available). When I connect the player, Windows plays the "USB connect" sound and the device appears (under its correct name) in the device manager, but it never appears as a drive. The player itself displays "USB Connected" for a split-second before reporting that it has been disconnected again. Since the player, by design, reboots after it has been disconnected, Windows plays the "USB disconnect" sound before restarting the whole cycle once the player has powered back on. I am connecting the player through an Intel X79 Chipset motherboard (Gigabyte GA-X79-UD3) to Windows 7 Pro 64-bit. The player used to work fine the first few times I connected it, showing up as an external drive; it only recently stopped working. It is not a problem with the player, since it works fine when connected to another computer, even such running the exact same operating system. It is also not a problem with the USB controller, since the issue is the same on both the Intel USB 2.0 and the Fresco Logic FL1009 USB 3.0 controller ports. I have also not had the problem with any other drive so far. Among the things I have tried so far: Disabling USB legacy mode in BIOS Disabling energy-saving power down for all USB controllers in Windows' device manager Removing and reinstalling Windows' USB mass storage driver Removing and reinstalling Intel and Fresco Logic USB controller driver Restoring the player to factory defaults None of these made a difference. Again, the player used to work fine on the exact same system just days ago; I didn't install any new hardware or drivers on it since then. I would be very grateful for any hints on what else to try. Edit: Here is another new hint; I found out that when I connect the drive before booting Windows, it is available in Windows Explorer as it should, and does not automatically disconnect. If I remove and reconnect it though, the infinite connect/disconnect-loop starts anew.

    Read the article

  • HttpWebRequest and Ignoring SSL Certificate Errors

    - by Rick Strahl
    Man I can't believe this. I'm still mucking around with OFX servers and it drives me absolutely crazy how some these servers are just so unbelievably misconfigured. I've recently hit three different 3 major brokerages which fail HTTP validation with bad or corrupt certificates at least according to the .NET WebRequest class. What's somewhat odd here though is that WinInet seems to find no issue with these servers - it's only .NET's Http client that's ultra finicky. So the question then becomes how do you tell HttpWebRequest to ignore certificate errors? In WinInet there used to be a host of flags to do this, but it's not quite so easy with WebRequest. Basically you need to configure the CertificatePolicy on the ServicePointManager by creating a custom policy. Not exactly trivial. Here's the code to hook it up: public bool CreateWebRequestObject(string Url) {    try     {        this.WebRequest =  (HttpWebRequest) System.Net.WebRequest.Create(Url);         if (this.IgnoreCertificateErrors)            ServicePointManager.CertificatePolicy = delegate { return true; };}One thing to watch out for is that this an application global setting. There's one global ServicePointManager and once you set this value any subsequent requests will inherit this policy as well, which may or may not be what you want. So it's probably a good idea to set the policy when the app starts and leave it be - otherwise you may run into odd behavior in some situations especially in multi-thread situations.Another way to deal with this is in you application .config file. Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} <configuration>   <system.net>     <settings>       <servicePointManager           checkCertificateName="false"           checkCertificateRevocationList="false"                />     </settings>   </system.net> </configuration> This seems to work most of the time, although I've seen some situations where it doesn't, but where the code implementation works which is frustrating. The .config settings aren't as inclusive as the programmatic code that can ignore any and all cert errors - shrug. Anyway, the code approach got me past the stopper issue. It still amazes me that theses OFX servers even require this. After all this is financial data we're talking about here. The last thing I want to do is disable extra checks on the certificates. Well I guess I shouldn't be surprised - these are the same companies that apparently don't believe in XML enough to generate valid XML (or even valid SGML for that matter)...© Rick Strahl, West Wind Technologies, 2005-2011Posted in .NET  CSharp  HTTP  

    Read the article

  • Installing Lubuntu 14.04.1 fails, upowerd appears to hang

    - by Rantanplan
    On the live-CD session, I tried installing Lubuntu double clicking on the install button on the desktop. Here, the CD starts running but then stops running and nothing happens. Next, I rebooted and tried installing Lubuntu directly from the boot menu screen using forcepae again. After a while, I receive the following error message: The installer encountered an unrecoverable error. A desktop session will now be run so that you may investigate the problem or try installing again. Hitting Enter brings me to the desktop. For what errors should I search? And how? Thanks for some hints! On Lubuntu 12.04: uname -a Linux humboldt 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:45:51 UTC 2014 i686 i686 i386 GNU/Linux lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.5 LTS Release: 12.04 Codename: precise upowerd appears to hang: Aug 25 10:53:28 lubuntu kernel: [ 367.920272] INFO: task upowerd:3002 blocked for more than 120 seconds. Aug 25 10:53:28 lubuntu kernel: [ 367.920288] Tainted: G S C 3.13.0-32-generic #57-Ubuntu Aug 25 10:53:28 lubuntu kernel: [ 367.920294] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 25 10:53:28 lubuntu kernel: [ 367.920300] upowerd D e21f9da0 0 3002 1 0x00000000 Aug 25 10:53:28 lubuntu kernel: [ 367.920314] e21f9dfc 00000086 f5ef7094 e21f9da0 c1050272 c1a8d540 c1920a00 00000000 Aug 25 10:53:28 lubuntu kernel: [ 367.920333] c1a8d540 c1920a00 d9e44da0 f5ef6540 c1129061 00000002 000001c1 0001c37b Aug 25 10:53:28 lubuntu kernel: [ 367.920351] 00000000 00000002 00000000 e2276240 00000000 00000040 c12b0ec5 c19975a8 Aug 25 10:53:28 lubuntu kernel: [ 367.920368] Call Trace: Aug 25 10:53:28 lubuntu kernel: [ 367.920389] [<c1050272>] ? kmap_atomic_prot+0x42/0x100 Aug 25 10:53:28 lubuntu kernel: [ 367.920404] [<c1129061>] ? get_page_from_freelist+0x2a1/0x600 Aug 25 10:53:28 lubuntu kernel: [ 367.920417] [<c12b0ec5>] ? process_measurement+0x65/0x240 Aug 25 10:53:28 lubuntu kernel: [ 367.920432] [<c1654c73>] schedule_preempt_disabled+0x23/0x60 Aug 25 10:53:28 lubuntu kernel: [ 367.920443] [<c16565bd>] __mutex_lock_slowpath+0x10d/0x171 Aug 25 10:53:28 lubuntu kernel: [ 367.920454] [<c1655aec>] mutex_lock+0x1c/0x28 Aug 25 10:53:28 lubuntu kernel: [ 367.920478] [<f857223a>] acpi_smbus_transaction+0x48/0x210 [sbshc] Aug 25 10:53:28 lubuntu kernel: [ 367.920489] [<c11858e1>] ? do_last+0x1b1/0xf60 Aug 25 10:53:28 lubuntu kernel: [ 367.920504] [<f857242f>] acpi_smbus_read+0x2d/0x33 [sbshc] Aug 25 10:53:28 lubuntu kernel: [ 367.920520] [<f881e0f1>] acpi_battery_get_state+0x74/0x8b [sbs] Aug 25 10:53:28 lubuntu kernel: [ 367.920535] [<f881e8a9>] acpi_sbs_battery_get_property+0x2a/0x233 [sbs] Aug 25 10:53:28 lubuntu kernel: [ 367.920549] [<c14fa61f>] power_supply_show_property+0x3f/0x240 Aug 25 10:53:28 lubuntu kernel: [ 367.920561] [<c114664f>] ? handle_mm_fault+0x64f/0x8d0 Aug 25 10:53:28 lubuntu kernel: [ 367.920573] [<c14fa5e0>] ? power_supply_store_property+0x60/0x60 Aug 25 10:53:28 lubuntu kernel: [ 367.920586] [<c1407d20>] ? dev_uevent_name+0x30/0x30 Aug 25 10:53:28 lubuntu kernel: [ 367.920597] [<c1407d38>] dev_attr_show+0x18/0x40 Aug 25 10:53:28 lubuntu kernel: [ 367.920608] [<c11dad15>] sysfs_seq_show+0xe5/0x1c0 Aug 25 10:53:28 lubuntu kernel: [ 367.920621] [<c119846e>] seq_read+0xce/0x370 Aug 25 10:53:28 lubuntu kernel: [ 367.920633] [<c11983a0>] ? seq_hlist_next_percpu+0x90/0x90 Aug 25 10:53:28 lubuntu kernel: [ 367.920644] [<c1179238>] vfs_read+0x78/0x140 Aug 25 10:53:28 lubuntu kernel: [ 367.920654] [<c11799a9>] SyS_read+0x49/0x90 Aug 25 10:53:28 lubuntu kernel: [ 367.920667] [<c165efcd>] sysenter_do_call+0x12/0x28 /var/log/installer/debug shows upower related error: Ubiquity 2.18.8 Gtk-Message: Failed to load module "overlay-scrollbar" Gtk-Message: Failed to load module "overlay-scrollbar" ERROR:dbus.proxies:Introspect error on :1.23:/org/freedesktop/UPower: dbus.exceptions.DBusException: org.freedesktop.DBus.Error.NoReply: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. Exception in GTK frontend (invoking crash handler): Traceback (most recent call last): File "/usr/lib/ubiquity/bin/ubiquity", line 636, in <module> main(oem_config) File "/usr/lib/ubiquity/bin/ubiquity", line 622, in main install(query=options.query) File "/usr/lib/ubiquity/bin/ubiquity", line 260, in install wizard = ui.Wizard(distro) File "/usr/lib/ubiquity/ubiquity/frontend/gtk_ui.py", line 290, in __init__ mod.ui = mod.ui_class(mod.controller) File "/usr/lib/ubiquity/plugins/ubi-prepare.py", line 93, in __init__ upower.setup_power_watch(self.prepare_power_source) File "/usr/lib/ubiquity/ubiquity/upower.py", line 21, in setup_power_watch power_state_changed() File "/usr/lib/ubiquity/ubiquity/upower.py", line 18, in power_state_changed not misc.get_prop(upower, UPOWER_PATH, 'OnBattery')) File "/usr/lib/ubiquity/ubiquity/misc.py", line 809, in get_prop return obj.Get(iface, prop, dbus_interface=dbus.PROPERTIES_IFACE) File "/usr/lib/python3/dist-packages/dbus/proxies.py", line 70, in __call__ return self._proxy_method(*args, **keywords) File "/usr/lib/python3/dist-packages/dbus/proxies.py", line 145, in __call__ **keywords) File "/usr/lib/python3/dist-packages/dbus/connection.py", line 651, in call_blocking message, timeout)

    Read the article

  • Agile Development

    - by James Oloo Onyango
    Alot of literature has and is being written about agile developement and its surrounding philosophies. In my quest to find the best way to express the importance of agile methodologies, i have found Robert C. Martin's "A Satire Of Two Companies" to be both the most concise and thorough! Enjoy the read! Rufus Inc Project Kick Off Your name is Bob. The date is January 3, 2001, and your head still aches from the recent millennial revelry. You are sitting in a conference room with several managers and a group of your peers. You are a project team leader. Your boss is there, and he has brought along all of his team leaders. His boss called the meeting. "We have a new project to develop," says your boss's boss. Call him BB. The points in his hair are so long that they scrape the ceiling. Your boss's points are just starting to grow, but he eagerly awaits the day when he can leave Brylcream stains on the acoustic tiles. BB describes the essence of the new market they have identified and the product they want to develop to exploit this market. "We must have this new project up and working by fourth quarter October 1," BB demands. "Nothing is of higher priority, so we are cancelling your current project." The reaction in the room is stunned silence. Months of work are simply going to be thrown away. Slowly, a murmur of objection begins to circulate around the conference table.   His points give off an evil green glow as BB meets the eyes of everyone in the room. One by one, that insidious stare reduces each attendee to quivering lumps of protoplasm. It is clear that he will brook no discussion on this matter. Once silence has been restored, BB says, "We need to begin immediately. How long will it take you to do the analysis?" You raise your hand. Your boss tries to stop you, but his spitwad misses you and you are unaware of his efforts.   "Sir, we can't tell you how long the analysis will take until we have some requirements." "The requirements document won't be ready for 3 or 4 weeks," BB says, his points vibrating with frustration. "So, pretend that you have the requirements in front of you now. How long will you require for analysis?" No one breathes. Everyone looks around to see whether anyone has some idea. "If analysis goes beyond April 1, we have a problem. Can you finish the analysis by then?" Your boss visibly gathers his courage: "We'll find a way, sir!" His points grow 3 mm, and your headache increases by two Tylenol. "Good." BB smiles. "Now, how long will it take to do the design?" "Sir," you say. Your boss visibly pales. He is clearly worried that his 3 mms are at risk. "Without an analysis, it will not be possible to tell you how long design will take." BB's expression shifts beyond austere.   "PRETEND you have the analysis already!" he says, while fixing you with his vacant, beady little eyes. "How long will it take you to do the design?" Two Tylenol are not going to cut it. Your boss, in a desperate attempt to save his new growth, babbles: "Well, sir, with only six months left to complete the project, design had better take no longer than 3 months."   "I'm glad you agree, Smithers!" BB says, beaming. Your boss relaxes. He knows his points are secure. After a while, he starts lightly humming the Brylcream jingle. BB continues, "So, analysis will be complete by April 1, design will be complete by July 1, and that gives you 3 months to implement the project. This meeting is an example of how well our new consensus and empowerment policies are working. Now, get out there and start working. I'll expect to see TQM plans and QIT assignments on my desk by next week. Oh, and don't forget that your crossfunctional team meetings and reports will be needed for next month's quality audit." "Forget the Tylenol," you think to yourself as you return to your cubicle. "I need bourbon."   Visibly excited, your boss comes over to you and says, "Gosh, what a great meeting. I think we're really going to do some world shaking with this project." You nod in agreement, too disgusted to do anything else. "Oh," your boss continues, "I almost forgot." He hands you a 30-page document. "Remember that the SEI is coming to do an evaluation next week. This is the evaluation guide. You need to read through it, memorize it, and then shred it. It tells you how to answer any questions that the SEI auditors ask you. It also tells you what parts of the building you are allowed to take them to and what parts to avoid. We are determined to be a CMM level 3 organization by June!"   You and your peers start working on the analysis of the new project. This is difficult because you have no requirements. But from the 10-minute introduction given by BB on that fateful morning, you have some idea of what the product is supposed to do.   Corporate process demands that you begin by creating a use case document. You and your team begin enumerating use cases and drawing oval and stick diagrams. Philosophical debates break out among the team members. There is disagreement as to whether certain use cases should be connected with <<extends>> or <<includes>> relationships. Competing models are created, but nobody knows how to evaluate them. The debate continues, effectively paralyzing progress.   After a week, somebody finds the iceberg.com Web site, which recommends disposing entirely of <<extends>> and <<includes>> and replacing them with <<precedes>> and <<uses>>. The documents on this Web site, authored by Don Sengroiux, describes a method known as stalwart-analysis, which claims to be a step-by-step method for translating use cases into design diagrams. More competing use case models are created using this new scheme, but again, people can't agree on how to evaluate them. The thrashing continues. More and more, the use case meetings are driven by emotion rather than by reason. If it weren't for the fact that you don't have requirements, you'd be pretty upset by the lack of progress you are making. The requirements document arrives on February 15. And then again on February 20, 25, and every week thereafter. Each new version contradicts the previous one. Clearly, the marketing folks who are writing the requirements, empowered though they might be, are not finding consensus.   At the same time, several new competing use case templates have been proposed by the various team members. Each template presents its own particularly creative way of delaying progress. The debates rage on. On March 1, Prudence Putrigence, the process proctor, succeeds in integrating all the competing use case forms and templates into a single, all-encompassing form. Just the blank form is 15 pages long. She has managed to include every field that appeared on all the competing templates. She also presents a 159- page document describing how to fill out the use case form. All current use cases must be rewritten according to the new standard.   You marvel to yourself that it now requires 15 pages of fill-in-the-blank and essay questions to answer the question: What should the system do when the user presses Return? The corporate process (authored by L. E. Ott, famed author of "Holistic Analysis: A Progressive Dialectic for Software Engineers") insists that you discover all primary use cases, 87 percent of all secondary use cases, and 36.274 percent of all tertiary use cases before you can complete analysis and enter the design phase. You have no idea what a tertiary use case is. So in an attempt to meet this requirement, you try to get your use case document reviewed by the marketing department, which you hope will know what a tertiary use case is.   Unfortunately, the marketing folks are too busy with sales support to talk to you. Indeed, since the project started, you have not been able to get a single meeting with marketing, which has provided a never-ending stream of changing and contradictory requirements documents.   While one team has been spinning endlessly on the use case document, another team has been working out the domain model. Endless variations of UML documents are pouring out of this team. Every week, the model is reworked.   The team members can't decide whether to use <<interfaces>> or <<types>> in the model. A huge disagreement has been raging on the proper syntax and application of OCL. Others on the team just got back from a 5-day class on catabolism, and have been producing incredibly detailed and arcane diagrams that nobody else can fathom.   On March 27, with one week to go before analysis is to be complete, you have produced a sea of documents and diagrams but are no closer to a cogent analysis of the problem than you were on January 3. **** And then, a miracle happens.   **** On Saturday, April 1, you check your e-mail from home. You see a memo from your boss to BB. It states unequivocally that you are done with the analysis! You phone your boss and complain. "How could you have told BB that we were done with the analysis?" "Have you looked at a calendar lately?" he responds. "It's April 1!" The irony of that date does not escape you. "But we have so much more to think about. So much more to analyze! We haven't even decided whether to use <<extends>> or <<precedes>>!" "Where is your evidence that you are not done?" inquires your boss, impatiently. "Whaaa . . . ." But he cuts you off. "Analysis can go on forever; it has to be stopped at some point. And since this is the date it was scheduled to stop, it has been stopped. Now, on Monday, I want you to gather up all existing analysis materials and put them into a public folder. Release that folder to Prudence so that she can log it in the CM system by Monday afternoon. Then get busy and start designing."   As you hang up the phone, you begin to consider the benefits of keeping a bottle of bourbon in your bottom desk drawer. They threw a party to celebrate the on-time completion of the analysis phase. BB gave a colon-stirring speech on empowerment. And your boss, another 3 mm taller, congratulated his team on the incredible show of unity and teamwork. Finally, the CIO takes the stage to tell everyone that the SEI audit went very well and to thank everyone for studying and shredding the evaluation guides that were passed out. Level 3 now seems assured and will be awarded by June. (Scuttlebutt has it that managers at the level of BB and above are to receive significant bonuses once the SEI awards level 3.)   As the weeks flow by, you and your team work on the design of the system. Of course, you find that the analysis that the design is supposedly based on is flawedno, useless; no, worse than useless. But when you tell your boss that you need to go back and work some more on the analysis to shore up its weaker sections, he simply states, "The analysis phase is over. The only allowable activity is design. Now get back to it."   So, you and your team hack the design as best you can, unsure of whether the requirements have been properly analyzed. Of course, it really doesn't matter much, since the requirements document is still thrashing with weekly revisions, and the marketing department still refuses to meet with you.     The design is a nightmare. Your boss recently misread a book named The Finish Line in which the author, Mark DeThomaso, blithely suggested that design documents should be taken down to code-level detail. "If we are going to be working at that level of detail," you ask, "why don't we simply write the code instead?" "Because then you wouldn't be designing, of course. And the only allowable activity in the design phase is design!" "Besides," he continues, "we have just purchased a companywide license for Dandelion! This tool enables 'Round the Horn Engineering!' You are to transfer all design diagrams into this tool. It will automatically generate our code for us! It will also keep the design diagrams in sync with the code!" Your boss hands you a brightly colored shrinkwrapped box containing the Dandelion distribution. You accept it numbly and shuffle off to your cubicle. Twelve hours, eight crashes, one disk reformatting, and eight shots of 151 later, you finally have the tool installed on your server. You consider the week your team will lose while attending Dandelion training. Then you smile and think, "Any week I'm not here is a good week." Design diagram after design diagram is created by your team. Dandelion makes it very difficult to draw these diagrams. There are dozens and dozens of deeply nested dialog boxes with funny text fields and check boxes that must all be filled in correctly. And then there's the problem of moving classes between packages. At first, these diagram are driven from the use cases. But the requirements are changing so often that the use cases rapidly become meaningless. Debates rage about whether VISITOR or DECORATOR design patterns should be used. One developer refuses to use VISITOR in any form, claiming that it's not a properly object-oriented construct. Someone refuses to use multiple inheritance, since it is the spawn of the devil. Review meetings rapidly degenerate into debates about the meaning of object orientation, the definition of analysis versus design, or when to use aggregation versus association. Midway through the design cycle, the marketing folks announce that they have rethought the focus of the system. Their new requirements document is completely restructured. They have eliminated several major feature areas and replaced them with feature areas that they anticipate customer surveys will show to be more appropriate. You tell your boss that these changes mean that you need to reanalyze and redesign much of the system. But he says, "The analysis phase is system. But he says, "The analysis phase is over. The only allowable activity is design. Now get back to it."   You suggest that it might be better to create a simple prototype to show to the marketing folks and even some potential customers. But your boss says, "The analysis phase is over. The only allowable activity is design. Now get back to it." Hack, hack, hack, hack. You try to create some kind of a design document that might reflect the new requirements documents. However, the revolution of the requirements has not caused them to stop thrashing. Indeed, if anything, the wild oscillations of the requirements document have only increased in frequency and amplitude.   You slog your way through them.   On June 15, the Dandelion database gets corrupted. Apparently, the corruption has been progressive. Small errors in the DB accumulated over the months into bigger and bigger errors. Eventually, the CASE tool just stopped working. Of course, the slowly encroaching corruption is present on all the backups. Calls to the Dandelion technical support line go unanswered for several days. Finally, you receive a brief e-mail from Dandelion, informing you that this is a known problem and that the solution is to purchase the new version, which they promise will be ready some time next quarter, and then reenter all the diagrams by hand.   ****   Then, on July 1 another miracle happens! You are done with the design!   Rather than go to your boss and complain, you stock your middle desk drawer with some vodka.   **** They threw a party to celebrate the on-time completion of the design phase and their graduation to CMM level 3. This time, you find BB's speech so stirring that you have to use the restroom before it begins. New banners and plaques are all over your workplace. They show pictures of eagles and mountain climbers, and they talk about teamwork and empowerment. They read better after a few scotches. That reminds you that you need to clear out your file cabinet to make room for the brandy. You and your team begin to code. But you rapidly discover that the design is lacking in some significant areas. Actually, it's lacking any significance at all. You convene a design session in one of the conference rooms to try to work through some of the nastier problems. But your boss catches you at it and disbands the meeting, saying, "The design phase is over. The only allowable activity is coding. Now get back to it."   ****   The code generated by Dandelion is really hideous. It turns out that you and your team were using association and aggregation the wrong way, after all. All the generated code has to be edited to correct these flaws. Editing this code is extremely difficult because it has been instrumented with ugly comment blocks that have special syntax that Dandelion needs in order to keep the diagrams in sync with the code. If you accidentally alter one of these comments, the diagrams will be regenerated incorrectly. It turns out that "Round the Horn Engineering" requires an awful lot of effort. The more you try to keep the code compatible with Dandelion, the more errors Dandelion generates. In the end, you give up and decide to keep the diagrams up to date manually. A second later, you decide that there's no point in keeping the diagrams up to date at all. Besides, who has time?   Your boss hires a consultant to build tools to count the number of lines of code that are being produced. He puts a big thermometer graph on the wall with the number 1,000,000 on the top. Every day, he extends the red line to show how many lines have been added. Three days after the thermometer appears on the wall, your boss stops you in the hall. "That graph isn't growing quickly enough. We need to have a million lines done by October 1." "We aren't even sh-sh-sure that the proshect will require a m-million linezh," you blather. "We have to have a million lines done by October 1," your boss reiterates. His points have grown again, and the Grecian formula he uses on them creates an aura of authority and competence. "Are you sure your comment blocks are big enough?" Then, in a flash of managerial insight, he says, "I have it! I want you to institute a new policy among the engineers. No line of code is to be longer than 20 characters. Any such line must be split into two or more preferably more. All existing code needs to be reworked to this standard. That'll get our line count up!"   You decide not to tell him that this will require two unscheduled work months. You decide not to tell him anything at all. You decide that intravenous injections of pure ethanol are the only solution. You make the appropriate arrangements. Hack, hack, hack, and hack. You and your team madly code away. By August 1, your boss, frowning at the thermometer on the wall, institutes a mandatory 50-hour workweek.   Hack, hack, hack, and hack. By September 1st, the thermometer is at 1.2 million lines and your boss asks you to write a report describing why you exceeded the coding budget by 20 percent. He institutes mandatory Saturdays and demands that the project be brought back down to a million lines. You start a campaign of remerging lines. Hack, hack, hack, and hack. Tempers are flaring; people are quitting; QA is raining trouble reports down on you. Customers are demanding installation and user manuals; salespeople are demanding advance demonstrations for special customers; the requirements document is still thrashing, the marketing folks are complaining that the product isn't anything like they specified, and the liquor store won't accept your credit card anymore. Something has to give.    On September 15, BB calls a meeting. As he enters the room, his points are emitting clouds of steam. When he speaks, the bass overtones of his carefully manicured voice cause the pit of your stomach to roll over. "The QA manager has told me that this project has less than 50 percent of the required features implemented. He has also informed me that the system crashes all the time, yields wrong results, and is hideously slow. He has also complained that he cannot keep up with the continuous train of daily releases, each more buggy than the last!" He stops for a few seconds, visibly trying to compose himself. "The QA manager estimates that, at this rate of development, we won't be able to ship the product until December!" Actually, you think it's more like March, but you don't say anything. "December!" BB roars with such derision that people duck their heads as though he were pointing an assault rifle at them. "December is absolutely out of the question. Team leaders, I want new estimates on my desk in the morning. I am hereby mandating 65-hour work weeks until this project is complete. And it better be complete by November 1."   As he leaves the conference room, he is heard to mutter: "Empowermentbah!" * * * Your boss is bald; his points are mounted on BB's wall. The fluorescent lights reflecting off his pate momentarily dazzle you. "Do you have anything to drink?" he asks. Having just finished your last bottle of Boone's Farm, you pull a bottle of Thunderbird from your bookshelf and pour it into his coffee mug. "What's it going to take to get this project done? " he asks. "We need to freeze the requirements, analyze them, design them, and then implement them," you say callously. "By November 1?" your boss exclaims incredulously. "No way! Just get back to coding the damned thing." He storms out, scratching his vacant head.   A few days later, you find that your boss has been transferred to the corporate research division. Turnover has skyrocketed. Customers, informed at the last minute that their orders cannot be fulfilled on time, have begun to cancel their orders. Marketing is re-evaluating whether this product aligns with the overall goals of the company. Memos fly, heads roll, policies change, and things are, overall, pretty grim. Finally, by March, after far too many sixty-five hour weeks, a very shaky version of the software is ready. In the field, bug-discovery rates are high, and the technical support staff are at their wits' end, trying to cope with the complaints and demands of the irate customers. Nobody is happy.   In April, BB decides to buy his way out of the problem by licensing a product produced by Rupert Industries and redistributing it. The customers are mollified, the marketing folks are smug, and you are laid off.     Rupert Industries: Project Alpha   Your name is Robert. The date is January 3, 2001. The quiet hours spent with your family this holiday have left you refreshed and ready for work. You are sitting in a conference room with your team of professionals. The manager of the division called the meeting. "We have some ideas for a new project," says the division manager. Call him Russ. He is a high-strung British chap with more energy than a fusion reactor. He is ambitious and driven but understands the value of a team. Russ describes the essence of the new market opportunity the company has identified and introduces you to Jane, the marketing manager, who is responsible for defining the products that will address it. Addressing you, Jane says, "We'd like to start defining our first product offering as soon as possible. When can you and your team meet with me?" You reply, "We'll be done with the current iteration of our project this Friday. We can spare a few hours for you between now and then. After that, we'll take a few people from the team and dedicate them to you. We'll begin hiring their replacements and the new people for your team immediately." "Great," says Russ, "but I want you to understand that it is critical that we have something to exhibit at the trade show coming up this July. If we can't be there with something significant, we'll lose the opportunity."   "I understand," you reply. "I don't yet know what it is that you have in mind, but I'm sure we can have something by July. I just can't tell you what that something will be right now. In any case, you and Jane are going to have complete control over what we developers do, so you can rest assured that by July, you'll have the most important things that can be accomplished in that time ready to exhibit."   Russ nods in satisfaction. He knows how this works. Your team has always kept him advised and allowed him to steer their development. He has the utmost confidence that your team will work on the most important things first and will produce a high-quality product.   * * *   "So, Robert," says Jane at their first meeting, "How does your team feel about being split up?" "We'll miss working with each other," you answer, "but some of us were getting pretty tired of that last project and are looking forward to a change. So, what are you people cooking up?" Jane beams. "You know how much trouble our customers currently have . . ." And she spends a half hour or so describing the problem and possible solution. "OK, wait a second" you respond. "I need to be clear about this." And so you and Jane talk about how this system might work. Some of her ideas aren't fully formed. You suggest possible solutions. She likes some of them. You continue discussing.   During the discussion, as each new topic is addressed, Jane writes user story cards. Each card represents something that the new system has to do. The cards accumulate on the table and are spread out in front of you. Both you and Jane point at them, pick them up, and make notes on them as you discuss the stories. The cards are powerful mnemonic devices that you can use to represent complex ideas that are barely formed.   At the end of the meeting, you say, "OK, I've got a general idea of what you want. I'm going to talk to the team about it. I imagine they'll want to run some experiments with various database structures and presentation formats. Next time we meet, it'll be as a group, and we'll start identifying the most important features of the system."   A week later, your nascent team meets with Jane. They spread the existing user story cards out on the table and begin to get into some of the details of the system. The meeting is very dynamic. Jane presents the stories in the order of their importance. There is much discussion about each one. The developers are concerned about keeping the stories small enough to estimate and test. So they continually ask Jane to split one story into several smaller stories. Jane is concerned that each story have a clear business value and priority, so as she splits them, she makes sure that this stays true.   The stories accumulate on the table. Jane writes them, but the developers make notes on them as needed. Nobody tries to capture everything that is said; the cards are not meant to capture everything but are simply reminders of the conversation.   As the developers become more comfortable with the stories, they begin writing estimates on them. These estimates are crude and budgetary, but they give Jane an idea of what the story will cost.   At the end of the meeting, it is clear that many more stories could be discussed. It is also clear that the most important stories have been addressed and that they represent several months worth of work. Jane closes the meeting by taking the cards with her and promising to have a proposal for the first release in the morning.   * * *   The next morning, you reconvene the meeting. Jane chooses five cards and places them on the table. "According to your estimates, these cards represent about one perfect team-week's worth of work. The last iteration of the previous project managed to get one perfect team-week done in 3 real weeks. If we can get these five stories done in 3 weeks, we'll be able to demonstrate them to Russ. That will make him feel very comfortable about our progress." Jane is pushing it. The sheepish look on her face lets you know that she knows it too. You reply, "Jane, this is a new team, working on a new project. It's a bit presumptuous to expect that our velocity will be the same as the previous team's. However, I met with the team yesterday afternoon, and we all agreed that our initial velocity should, in fact, be set to one perfectweek for every 3 real-weeks. So you've lucked out on this one." "Just remember," you continue, "that the story estimates and the story velocity are very tentative at this point. We'll learn more when we plan the iteration and even more when we implement it."   Jane looks over her glasses at you as if to say "Who's the boss around here, anyway?" and then smiles and says, "Yeah, don't worry. I know the drill by now."Jane then puts 15 more cards on the table. She says, "If we can get all these cards done by the end of March, we can turn the system over to our beta test customers. And we'll get good feedback from them."   You reply, "OK, so we've got our first iteration defined, and we have the stories for the next three iterations after that. These four iterations will make our first release."   "So," says Jane, can you really do these five stories in the next 3 weeks?" "I don't know for sure, Jane," you reply. "Let's break them down into tasks and see what we get."   So Jane, you, and your team spend the next several hours taking each of the five stories that Jane chose for the first iteration and breaking them down into small tasks. The developers quickly realize that some of the tasks can be shared between stories and that other tasks have commonalities that can probably be taken advantage of. It is clear that potential designs are popping into the developers' heads. From time to time, they form little discussion knots and scribble UML diagrams on some cards.   Soon, the whiteboard is filled with the tasks that, once completed, will implement the five stories for this iteration. You start the sign-up process by saying, "OK, let's sign up for these tasks." "I'll take the initial database generation." Says Pete. "That's what I did on the last project, and this doesn't look very different. I estimate it at two of my perfect workdays." "OK, well, then, I'll take the login screen," says Joe. "Aw, darn," says Elaine, the junior member of the team, "I've never done a GUI, and kinda wanted to try that one."   "Ah, the impatience of youth," Joe says sagely, with a wink in your direction. "You can assist me with it, young Jedi." To Jane: "I think it'll take me about three of my perfect workdays."   One by one, the developers sign up for tasks and estimate them in terms of their own perfect workdays. Both you and Jane know that it is best to let the developers volunteer for tasks than to assign the tasks to them. You also know full well that you daren't challenge any of the developers' estimates. You know these people, and you trust them. You know that they are going to do the very best they can.   The developers know that they can't sign up for more perfect workdays than they finished in the last iteration they worked on. Once each developer has filled his or her schedule for the iteration, they stop signing up for tasks.   Eventually, all the developers have stopped signing up for tasks. But, of course, tasks are still left on the board.   "I was worried that that might happen," you say, "OK, there's only one thing to do, Jane. We've got too much to do in this iteration. What stories or tasks can we remove?" Jane sighs. She knows that this is the only option. Working overtime at the beginning of a project is insane, and projects where she's tried it have not fared well.   So Jane starts to remove the least-important functionality. "Well, we really don't need the login screen just yet. We can simply start the system in the logged-in state." "Rats!" cries Elaine. "I really wanted to do that." "Patience, grasshopper." says Joe. "Those who wait for the bees to leave the hive will not have lips too swollen to relish the honey." Elaine looks confused. Everyone looks confused. "So . . .," Jane continues, "I think we can also do away with . . ." And so, bit by bit, the list of tasks shrinks. Developers who lose a task sign up for one of the remaining ones.   The negotiation is not painless. Several times, Jane exhibits obvious frustration and impatience. Once, when tensions are especially high, Elaine volunteers, "I'll work extra hard to make up some of the missing time." You are about to correct her when, fortunately, Joe looks her in the eye and says, "When once you proceed down the dark path, forever will it dominate your destiny."   In the end, an iteration acceptable to Jane is reached. It's not what Jane wanted. Indeed, it is significantly less. But it's something the team feels that can be achieved in the next 3 weeks.   And, after all, it still addresses the most important things that Jane wanted in the iteration. "So, Jane," you say when things had quieted down a bit, "when can we expect acceptance tests from you?" Jane sighs. This is the other side of the coin. For every story the development team implements,   Jane must supply a suite of acceptance tests that prove that it works. And the team needs these long before the end of the iteration, since they will certainly point out differences in the way Jane and the developers imagine the system's behaviour.   "I'll get you some example test scripts today," Jane promises. "I'll add to them every day after that. You'll have the entire suite by the middle of the iteration."   * * *   The iteration begins on Monday morning with a flurry of Class, Responsibilities, Collaborators sessions. By midmorning, all the developers have assembled into pairs and are rapidly coding away. "And now, my young apprentice," Joe says to Elaine, "you shall learn the mysteries of test-first design!"   "Wow, that sounds pretty rad," Elaine replies. "How do you do it?" Joe beams. It's clear that he has been anticipating this moment. "OK, what does the code do right now?" "Huh?" replied Elaine, "It doesn't do anything at all; there is no code."   "So, consider our task; can you think of something the code should do?" "Sure," Elaine said with youthful assurance, "First, it should connect to the database." "And thereupon, what must needs be required to connecteth the database?" "You sure talk weird," laughed Elaine. "I think we'd have to get the database object from some registry and call the Connect() method. "Ah, astute young wizard. Thou perceives correctly that we requireth an object within which we can cacheth the database object." "Is 'cacheth' really a word?" "It is when I say it! So, what test can we write that we know the database registry should pass?" Elaine sighs. She knows she'll just have to play along. "We should be able to create a database object and pass it to the registry in a Store() method. And then we should be able to pull it out of the registry with a Get() method and make sure it's the same object." "Oh, well said, my prepubescent sprite!" "Hay!" "So, now, let's write a test function that proves your case." "But shouldn't we write the database object and registry object first?" "Ah, you've much to learn, my young impatient one. Just write the test first." "But it won't even compile!" "Are you sure? What if it did?" "Uh . . ." "Just write the test, Elaine. Trust me." And so Joe, Elaine, and all the other developers began to code their tasks, one test case at a time. The room in which they worked was abuzz with the conversations between the pairs. The murmur was punctuated by an occasional high five when a pair managed to finish a task or a difficult test case.   As development proceeded, the developers changed partners once or twice a day. Each developer got to see what all the others were doing, and so knowledge of the code spread generally throughout the team.   Whenever a pair finished something significant whether a whole task or simply an important part of a task they integrated what they had with the rest of the system. Thus, the code base grew daily, and integration difficulties were minimized.   The developers communicated with Jane on a daily basis. They'd go to her whenever they had a question about the functionality of the system or the interpretation of an acceptance test case.   Jane, good as her word, supplied the team with a steady stream of acceptance test scripts. The team read these carefully and thereby gained a much better understanding of what Jane expected the system to do. By the beginning of the second week, there was enough functionality to demonstrate to Jane. She watched eagerly as the demonstration passed test case after test case. "This is really cool," Jane said as the demonstration finally ended. "But this doesn't seem like one-third of the tasks. Is your velocity slower than anticipated?"   You grimace. You'd been waiting for a good time to mention this to Jane but now she was forcing the issue. "Yes, unfortunately, we are going more slowly than we had expected. The new application server we are using is turning out to be a pain to configure. Also, it takes forever to reboot, and we have to reboot it whenever we make even the slightest change to its configuration."   Jane eyes you with suspicion. The stress of last Monday's negotiations had still not entirely dissipated. She says, "And what does this mean to our schedule? We can't slip it again, we just can't. Russ will have a fit! He'll haul us all into the woodshed and ream us some new ones."   You look Jane right in the eyes. There's no pleasant way to give someone news like this. So you just blurt out, "Look, if things keep going like they're going, we're not going to be done with everything by next Friday. Now it's possible that we'll figure out a way to go faster. But, frankly, I wouldn't depend on that. You should start thinking about one or two tasks that could be removed from the iteration without ruining the demonstration for Russ. Come hell or high water, we are going to give that demonstration on Friday, and I don't think you want us to choose which tasks to omit."   "Aw forchrisakes!" Jane barely manages to stifle yelling that last word as she stalks away, shaking her head. Not for the first time, you say to yourself, "Nobody ever promised me project management would be easy." You are pretty sure it won't be the last time, either.   Actually, things went a bit better than you had hoped. The team did, in fact, have to drop one task from the iteration, but Jane had chosen wisely, and the demonstration for Russ went without a hitch. Russ was not impressed with the progress, but neither was he dismayed. He simply said, "This is pretty good. But remember, we have to be able to demonstrate this system at the trade show in July, and at this rate, it doesn't look like you'll have all that much to show." Jane, whose attitude had improved dramatically with the completion of the iteration, responded to Russ by saying, "Russ, this team is working hard, and well. When July comes around, I am confident that we'll have something significant to demonstrate. It won't be everything, and some of it may be smoke and mirrors, but we'll have something."   Painful though the last iteration was, it had calibrated your velocity numbers. The next iteration went much better. Not because your team got more done than in the last iteration but simply because the team didn't have to remove any tasks or stories in the middle of the iteration.   By the start of the fourth iteration, a natural rhythm has been established. Jane, you, and the team know exactly what to expect from one another. The team is running hard, but the pace is sustainable. You are confident that the team can keep up this pace for a year or more.   The number of surprises in the schedule diminishes to near zero; however, the number of surprises in the requirements does not. Jane and Russ frequently look over the growing system and make recommendations or changes to the existing functionality. But all parties realize that these changes take time and must be scheduled. So the changes do not cause anyone's expectations to be violated. In March, there is a major demonstration of the system to the board of directors. The system is very limited and is not yet in a form good enough to take to the trade show, but progress is steady, and the board is reasonably impressed.   The second release goes even more smoothly than the first. By now, the team has figured out a way to automate Jane's acceptance test scripts. The team has also refactored the design of the system to the point that it is really easy to add new features and change old ones. The second release was done by the end of June and was taken to the trade show. It had less in it than Jane and Russ would have liked, but it did demonstrate the most important features of the system. Although customers at the trade show noticed that certain features were missing, they were very impressed overall. You, Russ, and Jane all returned from the trade show with smiles on your faces. You all felt as though this project was a winner.   Indeed, many months later, you are contacted by Rufus Inc. That company had been working on a system like this for its internal operations. Rufus has canceled the development of that system after a death-march project and is negotiating to license your technology for its environment.   Indeed, things are looking up!

    Read the article

  • SQLite, python, unicode, and non-utf data

    - by Nathan Spears
    I started by trying to store strings in sqlite using python, and got the message: sqlite3.ProgrammingError: You must not use 8-bit bytestrings unless you use a text_factory that can interpret 8-bit bytestrings (like text_factory = str). It is highly recommended that you instead just switch your application to Unicode strings. Ok, I switched to Unicode strings. Then I started getting the message: sqlite3.OperationalError: Could not decode to UTF-8 column 'tag_artist' with text 'Sigur Rós' when trying to retrieve data from the db. More research and I started encoding it in utf8, but then 'Sigur Rós' starts looking like 'Sigur Rós' note: My console was set to display in 'latin_1' as @John Machin pointed out. What gives? After reading this, describing exactly the same situation I'm in, it seems as if the advice is to ignore the other advice and use 8-bit bytestrings after all. I didn't know much about unicode and utf before I started this process. I've learned quite a bit in the last couple hours, but I'm still ignorant of whether there is a way to correctly convert 'ó' from latin-1 to utf-8 and not mangle it. If there isn't, why would sqlite 'highly recommend' I switch my application to unicode strings? I'm going to update this question with a summary and some example code of everything I've learned in the last 24 hours so that someone in my shoes can have an easy(er) guide. If the information I post is wrong or misleading in any way please tell me and I'll update, or one of you senior guys can update. Summary of answers Let me first state the goal as I understand it. The goal in processing various encodings, if you are trying to convert between them, is to understand what your source encoding is, then convert it to unicode using that source encoding, then convert it to your desired encoding. Unicode is a base and encodings are mappings of subsets of that base. utf_8 has room for every character in unicode, but because they aren't in the same place as, for instance, latin_1, a string encoded in utf_8 and sent to a latin_1 console will not look the way you expect. In python the process of getting to unicode and into another encoding looks like: str.decode('source_encoding').encode('desired_encoding') or if the str is already in unicode str.encode('desired_encoding') For sqlite I didn't actually want to encode it again, I wanted to decode it and leave it in unicode format. Here are four things you might need to be aware of as you try to work with unicode and encodings in python. The encoding of the string you want to work with, and the encoding you want to get it to. The system encoding. The console encoding. The encoding of the source file Elaboration: (1) When you read a string from a source, it must have some encoding, like latin_1 or utf_8. In my case, I'm getting strings from filenames, so unfortunately, I could be getting any kind of encoding. Windows XP uses UCS-2 (a Unicode system) as its native string type, which seems like cheating to me. Fortunately for me, the characters in most filenames are not going to be made up of more than one source encoding type, and I think all of mine were either completely latin_1, completely utf_8, or just plain ascii (which is a subset of both of those). So I just read them and decoded them as if they were still in latin_1 or utf_8. It's possible, though, that you could have latin_1 and utf_8 and whatever other characters mixed together in a filename on Windows. Sometimes those characters can show up as boxes, other times they just look mangled, and other times they look correct (accented characters and whatnot). Moving on. (2) Python has a default system encoding that gets set when python starts and can't be changed during runtime. See here for details. Dirty summary ... well here's the file I added: \# sitecustomize.py \# this file can be anywhere in your Python path, \# but it usually goes in ${pythondir}/lib/site-packages/ import sys sys.setdefaultencoding('utf_8') This system encoding is the one that gets used when you use the unicode("str") function without any other encoding parameters. To say that another way, python tries to decode "str" to unicode based on the default system encoding. (3) If you're using IDLE or the command-line python, I think that your console will display according to the default system encoding. I am using pydev with eclipse for some reason, so I had to go into my project settings, edit the launch configuration properties of my test script, go to the Common tab, and change the console from latin-1 to utf-8 so that I could visually confirm what I was doing was working. (4) If you want to have some test strings, eg test_str = "ó" in your source code, then you will have to tell python what kind of encoding you are using in that file. (FYI: when I mistyped an encoding I had to ctrl-Z because my file became unreadable.) This is easily accomplished by putting a line like so at the top of your source code file: # -*- coding: utf_8 -*- If you don't have this information, python attempts to parse your code as ascii by default, and so: SyntaxError: Non-ASCII character '\xf3' in file _redacted_ on line 81, but no encoding declared; see http://www.python.org/peps/pep-0263.html for details Once your program is working correctly, or, if you aren't using python's console or any other console to look at output, then you will probably really only care about #1 on the list. System default and console encoding are not that important unless you need to look at output and/or you are using the builtin unicode() function (without any encoding parameters) instead of the string.decode() function. I wrote a demo function I will paste into the bottom of this gigantic mess that I hope correctly demonstrates the items in my list. Here is some of the output when I run the character 'ó' through the demo function, showing how various methods react to the character as input. My system encoding and console output are both set to utf_8 for this run: '?' = original char <type 'str'> repr(char)='\xf3' '?' = unicode(char) ERROR: 'utf8' codec can't decode byte 0xf3 in position 0: unexpected end of data 'ó' = char.decode('latin_1') <type 'unicode'> repr(char.decode('latin_1'))=u'\xf3' '?' = char.decode('utf_8') ERROR: 'utf8' codec can't decode byte 0xf3 in position 0: unexpected end of data Now I will change the system and console encoding to latin_1, and I get this output for the same input: 'ó' = original char <type 'str'> repr(char)='\xf3' 'ó' = unicode(char) <type 'unicode'> repr(unicode(char))=u'\xf3' 'ó' = char.decode('latin_1') <type 'unicode'> repr(char.decode('latin_1'))=u'\xf3' '?' = char.decode('utf_8') ERROR: 'utf8' codec can't decode byte 0xf3 in position 0: unexpected end of data Notice that the 'original' character displays correctly and the builtin unicode() function works now. Now I change my console output back to utf_8. '?' = original char <type 'str'> repr(char)='\xf3' '?' = unicode(char) <type 'unicode'> repr(unicode(char))=u'\xf3' '?' = char.decode('latin_1') <type 'unicode'> repr(char.decode('latin_1'))=u'\xf3' '?' = char.decode('utf_8') ERROR: 'utf8' codec can't decode byte 0xf3 in position 0: unexpected end of data Here everything still works the same as last time but the console can't display the output correctly. Etc. The function below also displays more information that this and hopefully would help someone figure out where the gap in their understanding is. I know all this information is in other places and more thoroughly dealt with there, but I hope that this would be a good kickoff point for someone trying to get coding with python and/or sqlite. Ideas are great but sometimes source code can save you a day or two of trying to figure out what functions do what. Disclaimers: I'm no encoding expert, I put this together to help my own understanding. I kept building on it when I should have probably started passing functions as arguments to avoid so much redundant code, so if I can I'll make it more concise. Also, utf_8 and latin_1 are by no means the only encoding schemes, they are just the two I was playing around with because I think they handle everything I need. Add your own encoding schemes to the demo function and test your own input. One more thing: there are apparently crazy application developers making life difficult in Windows. #!/usr/bin/env python # -*- coding: utf_8 -*- import os import sys def encodingDemo(str): validStrings = () try: print "str =",str,"{0} repr(str) = {1}".format(type(str), repr(str)) validStrings += ((str,""),) except UnicodeEncodeError as ude: print "Couldn't print the str itself because the console is set to an encoding that doesn't understand some character in the string. See error:\n\t", print ude try: x = unicode(str) print "unicode(str) = ",x validStrings+= ((x, " decoded into unicode by the default system encoding"),) except UnicodeDecodeError as ude: print "ERROR. unicode(str) couldn't decode the string because the system encoding is set to an encoding that doesn't understand some character in the string." print "\tThe system encoding is set to {0}. See error:\n\t".format(sys.getdefaultencoding()), print ude except UnicodeEncodeError as uee: print "ERROR. Couldn't print the unicode(str) because the console is set to an encoding that doesn't understand some character in the string. See error:\n\t", print uee try: x = str.decode('latin_1') print "str.decode('latin_1') =",x validStrings+= ((x, " decoded with latin_1 into unicode"),) try: print "str.decode('latin_1').encode('utf_8') =",str.decode('latin_1').encode('utf_8') validStrings+= ((x, " decoded with latin_1 into unicode and encoded into utf_8"),) except UnicodeDecodeError as ude: print "The string was decoded into unicode using the latin_1 encoding, but couldn't be encoded into utf_8. See error:\n\t", print ude except UnicodeDecodeError as ude: print "Something didn't work, probably because the string wasn't latin_1 encoded. See error:\n\t", print ude except UnicodeEncodeError as uee: print "ERROR. Couldn't print the str.decode('latin_1') because the console is set to an encoding that doesn't understand some character in the string. See error:\n\t", print uee try: x = str.decode('utf_8') print "str.decode('utf_8') =",x validStrings+= ((x, " decoded with utf_8 into unicode"),) try: print "str.decode('utf_8').encode('latin_1') =",str.decode('utf_8').encode('latin_1') except UnicodeDecodeError as ude: print "str.decode('utf_8').encode('latin_1') didn't work. The string was decoded into unicode using the utf_8 encoding, but couldn't be encoded into latin_1. See error:\n\t", validStrings+= ((x, " decoded with utf_8 into unicode and encoded into latin_1"),) print ude except UnicodeDecodeError as ude: print "str.decode('utf_8') didn't work, probably because the string wasn't utf_8 encoded. See error:\n\t", print ude except UnicodeEncodeError as uee: print "ERROR. Couldn't print the str.decode('utf_8') because the console is set to an encoding that doesn't understand some character in the string. See error:\n\t",uee print print "Printing information about each character in the original string." for char in str: try: print "\t'" + char + "' = original char {0} repr(char)={1}".format(type(char), repr(char)) except UnicodeDecodeError as ude: print "\t'?' = original char {0} repr(char)={1} ERROR PRINTING: {2}".format(type(char), repr(char), ude) except UnicodeEncodeError as uee: print "\t'?' = original char {0} repr(char)={1} ERROR PRINTING: {2}".format(type(char), repr(char), uee) print uee try: x = unicode(char) print "\t'" + x + "' = unicode(char) {1} repr(unicode(char))={2}".format(x, type(x), repr(x)) except UnicodeDecodeError as ude: print "\t'?' = unicode(char) ERROR: {0}".format(ude) except UnicodeEncodeError as uee: print "\t'?' = unicode(char) {0} repr(char)={1} ERROR PRINTING: {2}".format(type(x), repr(x), uee) try: x = char.decode('latin_1') print "\t'" + x + "' = char.decode('latin_1') {1} repr(char.decode('latin_1'))={2}".format(x, type(x), repr(x)) except UnicodeDecodeError as ude: print "\t'?' = char.decode('latin_1') ERROR: {0}".format(ude) except UnicodeEncodeError as uee: print "\t'?' = char.decode('latin_1') {0} repr(char)={1} ERROR PRINTING: {2}".format(type(x), repr(x), uee) try: x = char.decode('utf_8') print "\t'" + x + "' = char.decode('utf_8') {1} repr(char.decode('utf_8'))={2}".format(x, type(x), repr(x)) except UnicodeDecodeError as ude: print "\t'?' = char.decode('utf_8') ERROR: {0}".format(ude) except UnicodeEncodeError as uee: print "\t'?' = char.decode('utf_8') {0} repr(char)={1} ERROR PRINTING: {2}".format(type(x), repr(x), uee) print x = 'ó' encodingDemo(x) Much thanks for the answers below and especially to @John Machin for answering so thoroughly.

    Read the article

  • Windows Phone 7 development: Using isolated storage

    - by DigiMortal
    In my previous posting about Windows Phone 7 development I showed how to use WebBrowser control in Windows Phone 7. In this posting I make some other improvements to my blog reader application and I will show you how to use isolated storage to store information to phone. Why isolated storage? Isolated storage is place where your application can save its data and settings. The image on right (that I stole from MSDN library) shows you how application data store is organized. You have no other options to keep your files besides isolated storage because Windows Phone 7 does not allow you to save data directly to other file system locations. From MSDN: “Isolated storage enables managed applications to create and maintain local storage. The mobile architecture is similar to the Silverlight-based applications on Windows. All I/O operations are restricted to isolated storage and do not have direct access to the underlying operating system file system. Ultimately, this helps to provide security and prevents unauthorized access and data corruption.” Saving files from web to isolated storage I updated my RSS-reader so it reads RSS from web only if there in no local file with RSS. User can update RSS-file by clicking a button. Also file is created when application starts and there is no RSS-file. Why I am doing this? I want my application to be able to work also offline. As my code needs some more refactoring I provide it with some next postings about Windows Phone 7. If you want it sooner then please leave me a comment here. Here is the code for my RSS-downloader that downloads RSS-feed and saves it to isolated storage file calles rss.xml. public class RssDownloader {     private string _url;     private string _fileName;       public delegate void DownloadCompleteDelegate();     public event DownloadCompleteDelegate DownloadComplete;       public RssDownloader(string url, string fileName)     {         _url = url;         _fileName = fileName;     }       public void Download()     {         var request = (HttpWebRequest)WebRequest.Create(_url);         var result = (IAsyncResult)request.BeginGetResponse(ResponseCallback, request);            }       private void ResponseCallback(IAsyncResult result)     {         var request = (HttpWebRequest)result.AsyncState;         var response = request.EndGetResponse(result);           using(var stream = response.GetResponseStream())         using(var reader = new StreamReader(stream))         using(var appStorage = IsolatedStorageFile.GetUserStoreForApplication())         using(var file = appStorage.OpenFile("rss.xml", FileMode.OpenOrCreate))         using(var writer = new StreamWriter(file))         {             writer.Write(reader.ReadToEnd());         }           if (DownloadComplete != null)             DownloadComplete();     } } Of course I modified RSS-source for my application to use rss.xml file from isolated storage. As isolated storage files also base on streams we can use them everywhere where streams are expected. Reading isolated storage files As isolated storage files are opened as streams you can read them like usual files in your usual applications. The next code fragment shows you how to open file from isolated storage and how to read it using XmlReader. Previously I used response stream in same place. using(var appStorage = IsolatedStorageFile.GetUserStoreForApplication()) using(var file = appStorage.OpenFile("rss.xml", FileMode.Open)) {     var reader = XmlReader.Create(file);                      // more code } As you can see there is nothing complex. If you have worked with System.IO namespace objects then you will find isolated storage classes and methods to be very similar to these. Also mention that application storage and isolated storage files must be disposed after you are not using them anymore.

    Read the article

  • SQLite, python, unicode, and non-utf data

    - by Nathan Spears
    I started by trying to store strings in sqlite using python, and got the message: sqlite3.ProgrammingError: You must not use 8-bit bytestrings unless you use a text_factory that can interpret 8-bit bytestrings (like text_factory = str). It is highly recommended that you instead just switch your application to Unicode strings. Ok, I switched to Unicode strings. Then I started getting the message: sqlite3.OperationalError: Could not decode to UTF-8 column 'tag_artist' with text 'Sigur Rós' when trying to retrieve data from the db. More research and I started encoding it in utf8, but then 'Sigur Rós' starts looking like 'Sigur Rós' note: My console was set to display in 'latin_1' as @John Machin pointed out. What gives? After reading this, describing exactly the same situation I'm in, it seems as if the advice is to ignore the other advice and use 8-bit bytestrings after all. I didn't know much about unicode and utf before I started this process. I've learned quite a bit in the last couple hours, but I'm still ignorant of whether there is a way to correctly convert 'ó' from latin-1 to utf-8 and not mangle it. If there isn't, why would sqlite 'highly recommend' I switch my application to unicode strings? I'm going to update this question with a summary and some example code of everything I've learned in the last 24 hours so that someone in my shoes can have an easy(er) guide. If the information I post is wrong or misleading in any way please tell me and I'll update, or one of you senior guys can update. Summary of answers Let me first state the goal as I understand it. The goal in processing various encodings, if you are trying to convert between them, is to understand what your source encoding is, then convert it to unicode using that source encoding, then convert it to your desired encoding. Unicode is a base and encodings are mappings of subsets of that base. utf_8 has room for every character in unicode, but because they aren't in the same place as, for instance, latin_1, a string encoded in utf_8 and sent to a latin_1 console will not look the way you expect. In python the process of getting to unicode and into another encoding looks like: str.decode('source_encoding').encode('desired_encoding') or if the str is already in unicode str.encode('desired_encoding') For sqlite I didn't actually want to encode it again, I wanted to decode it and leave it in unicode format. Here are four things you might need to be aware of as you try to work with unicode and encodings in python. The encoding of the string you want to work with, and the encoding you want to get it to. The system encoding. The console encoding. The encoding of the source file Elaboration: (1) When you read a string from a source, it must have some encoding, like latin_1 or utf_8. In my case, I'm getting strings from filenames, so unfortunately, I could be getting any kind of encoding. Windows XP uses UCS-2 (a Unicode system) as its native string type, which seems like cheating to me. Fortunately for me, the characters in most filenames are not going to be made up of more than one source encoding type, and I think all of mine were either completely latin_1, completely utf_8, or just plain ascii (which is a subset of both of those). So I just read them and decoded them as if they were still in latin_1 or utf_8. It's possible, though, that you could have latin_1 and utf_8 and whatever other characters mixed together in a filename on Windows. Sometimes those characters can show up as boxes, other times they just look mangled, and other times they look correct (accented characters and whatnot). Moving on. (2) Python has a default system encoding that gets set when python starts and can't be changed during runtime. See here for details. Dirty summary ... well here's the file I added: \# sitecustomize.py \# this file can be anywhere in your Python path, \# but it usually goes in ${pythondir}/lib/site-packages/ import sys sys.setdefaultencoding('utf_8') This system encoding is the one that gets used when you use the unicode("str") function without any other encoding parameters. To say that another way, python tries to decode "str" to unicode based on the default system encoding. (3) If you're using IDLE or the command-line python, I think that your console will display according to the default system encoding. I am using pydev with eclipse for some reason, so I had to go into my project settings, edit the launch configuration properties of my test script, go to the Common tab, and change the console from latin-1 to utf-8 so that I could visually confirm what I was doing was working. (4) If you want to have some test strings, eg test_str = "ó" in your source code, then you will have to tell python what kind of encoding you are using in that file. (FYI: when I mistyped an encoding I had to ctrl-Z because my file became unreadable.) This is easily accomplished by putting a line like so at the top of your source code file: # -*- coding: utf_8 -*- If you don't have this information, python attempts to parse your code as ascii by default, and so: SyntaxError: Non-ASCII character '\xf3' in file _redacted_ on line 81, but no encoding declared; see http://www.python.org/peps/pep-0263.html for details Once your program is working correctly, or, if you aren't using python's console or any other console to look at output, then you will probably really only care about #1 on the list. System default and console encoding are not that important unless you need to look at output and/or you are using the builtin unicode() function (without any encoding parameters) instead of the string.decode() function. I wrote a demo function I will paste into the bottom of this gigantic mess that I hope correctly demonstrates the items in my list. Here is some of the output when I run the character 'ó' through the demo function, showing how various methods react to the character as input. My system encoding and console output are both set to utf_8 for this run: '?' = original char <type 'str'> repr(char)='\xf3' '?' = unicode(char) ERROR: 'utf8' codec can't decode byte 0xf3 in position 0: unexpected end of data 'ó' = char.decode('latin_1') <type 'unicode'> repr(char.decode('latin_1'))=u'\xf3' '?' = char.decode('utf_8') ERROR: 'utf8' codec can't decode byte 0xf3 in position 0: unexpected end of data Now I will change the system and console encoding to latin_1, and I get this output for the same input: 'ó' = original char <type 'str'> repr(char)='\xf3' 'ó' = unicode(char) <type 'unicode'> repr(unicode(char))=u'\xf3' 'ó' = char.decode('latin_1') <type 'unicode'> repr(char.decode('latin_1'))=u'\xf3' '?' = char.decode('utf_8') ERROR: 'utf8' codec can't decode byte 0xf3 in position 0: unexpected end of data Notice that the 'original' character displays correctly and the builtin unicode() function works now. Now I change my console output back to utf_8. '?' = original char <type 'str'> repr(char)='\xf3' '?' = unicode(char) <type 'unicode'> repr(unicode(char))=u'\xf3' '?' = char.decode('latin_1') <type 'unicode'> repr(char.decode('latin_1'))=u'\xf3' '?' = char.decode('utf_8') ERROR: 'utf8' codec can't decode byte 0xf3 in position 0: unexpected end of data Here everything still works the same as last time but the console can't display the output correctly. Etc. The function below also displays more information that this and hopefully would help someone figure out where the gap in their understanding is. I know all this information is in other places and more thoroughly dealt with there, but I hope that this would be a good kickoff point for someone trying to get coding with python and/or sqlite. Ideas are great but sometimes source code can save you a day or two of trying to figure out what functions do what. Disclaimers: I'm no encoding expert, I put this together to help my own understanding. I kept building on it when I should have probably started passing functions as arguments to avoid so much redundant code, so if I can I'll make it more concise. Also, utf_8 and latin_1 are by no means the only encoding schemes, they are just the two I was playing around with because I think they handle everything I need. Add your own encoding schemes to the demo function and test your own input. One more thing: there are apparently crazy application developers making life difficult in Windows. #!/usr/bin/env python # -*- coding: utf_8 -*- import os import sys def encodingDemo(str): validStrings = () try: print "str =",str,"{0} repr(str) = {1}".format(type(str), repr(str)) validStrings += ((str,""),) except UnicodeEncodeError as ude: print "Couldn't print the str itself because the console is set to an encoding that doesn't understand some character in the string. See error:\n\t", print ude try: x = unicode(str) print "unicode(str) = ",x validStrings+= ((x, " decoded into unicode by the default system encoding"),) except UnicodeDecodeError as ude: print "ERROR. unicode(str) couldn't decode the string because the system encoding is set to an encoding that doesn't understand some character in the string." print "\tThe system encoding is set to {0}. See error:\n\t".format(sys.getdefaultencoding()), print ude except UnicodeEncodeError as uee: print "ERROR. Couldn't print the unicode(str) because the console is set to an encoding that doesn't understand some character in the string. See error:\n\t", print uee try: x = str.decode('latin_1') print "str.decode('latin_1') =",x validStrings+= ((x, " decoded with latin_1 into unicode"),) try: print "str.decode('latin_1').encode('utf_8') =",str.decode('latin_1').encode('utf_8') validStrings+= ((x, " decoded with latin_1 into unicode and encoded into utf_8"),) except UnicodeDecodeError as ude: print "The string was decoded into unicode using the latin_1 encoding, but couldn't be encoded into utf_8. See error:\n\t", print ude except UnicodeDecodeError as ude: print "Something didn't work, probably because the string wasn't latin_1 encoded. See error:\n\t", print ude except UnicodeEncodeError as uee: print "ERROR. Couldn't print the str.decode('latin_1') because the console is set to an encoding that doesn't understand some character in the string. See error:\n\t", print uee try: x = str.decode('utf_8') print "str.decode('utf_8') =",x validStrings+= ((x, " decoded with utf_8 into unicode"),) try: print "str.decode('utf_8').encode('latin_1') =",str.decode('utf_8').encode('latin_1') except UnicodeDecodeError as ude: print "str.decode('utf_8').encode('latin_1') didn't work. The string was decoded into unicode using the utf_8 encoding, but couldn't be encoded into latin_1. See error:\n\t", validStrings+= ((x, " decoded with utf_8 into unicode and encoded into latin_1"),) print ude except UnicodeDecodeError as ude: print "str.decode('utf_8') didn't work, probably because the string wasn't utf_8 encoded. See error:\n\t", print ude except UnicodeEncodeError as uee: print "ERROR. Couldn't print the str.decode('utf_8') because the console is set to an encoding that doesn't understand some character in the string. See error:\n\t",uee print print "Printing information about each character in the original string." for char in str: try: print "\t'" + char + "' = original char {0} repr(char)={1}".format(type(char), repr(char)) except UnicodeDecodeError as ude: print "\t'?' = original char {0} repr(char)={1} ERROR PRINTING: {2}".format(type(char), repr(char), ude) except UnicodeEncodeError as uee: print "\t'?' = original char {0} repr(char)={1} ERROR PRINTING: {2}".format(type(char), repr(char), uee) print uee try: x = unicode(char) print "\t'" + x + "' = unicode(char) {1} repr(unicode(char))={2}".format(x, type(x), repr(x)) except UnicodeDecodeError as ude: print "\t'?' = unicode(char) ERROR: {0}".format(ude) except UnicodeEncodeError as uee: print "\t'?' = unicode(char) {0} repr(char)={1} ERROR PRINTING: {2}".format(type(x), repr(x), uee) try: x = char.decode('latin_1') print "\t'" + x + "' = char.decode('latin_1') {1} repr(char.decode('latin_1'))={2}".format(x, type(x), repr(x)) except UnicodeDecodeError as ude: print "\t'?' = char.decode('latin_1') ERROR: {0}".format(ude) except UnicodeEncodeError as uee: print "\t'?' = char.decode('latin_1') {0} repr(char)={1} ERROR PRINTING: {2}".format(type(x), repr(x), uee) try: x = char.decode('utf_8') print "\t'" + x + "' = char.decode('utf_8') {1} repr(char.decode('utf_8'))={2}".format(x, type(x), repr(x)) except UnicodeDecodeError as ude: print "\t'?' = char.decode('utf_8') ERROR: {0}".format(ude) except UnicodeEncodeError as uee: print "\t'?' = char.decode('utf_8') {0} repr(char)={1} ERROR PRINTING: {2}".format(type(x), repr(x), uee) print x = 'ó' encodingDemo(x) Much thanks for the answers below and especially to @John Machin for answering so thoroughly.

    Read the article

  • Searching for tasks with code – Executables and Event Handlers

    Searching packages or just enumerating through all tasks is not quite as straightforward as it may first appear, mainly because of the way you can nest tasks within other containers. You can see this illustrated in the sample package below where I have used several sequence containers and loops. To complicate this further all containers types, including packages and tasks, can have event handlers which can then support the full range of nested containers again. Towards the lower right, the task called SQL In FEL also has an event handler not shown, within which is another Execute SQL Task, so that makes a total of 6 Execute SQL Tasks 6 tasks spread across the package. In my previous post about such as adding a property expressionI kept it simple and just looked at tasks at the package level, but what if you wanted to find any or all tasks in a package? For this post I've written a console program that will search a package looking at all tasks no matter how deeply nested, and check to see if the name starts with "SQL". When it finds a matching task it writes out the hierarchy by name for that task, starting with the package and working down to the task itself. The output for our sample package is shown below, note it has found all 6 tasks, including the one on the OnPreExecute event of the SQL In FEL task TaskSearch v1.0.0.0 (1.0.0.0) Copyright (C) 2009 Konesans Ltd Processing File - C:\Projects\Alpha\Packages\MyPackage.dtsx MyPackage\FOR Counter Loop\SQL In Counter Loop MyPackage\SEQ For Each Loop Wrapper\FEL Simple Loop\SQL In FEL MyPackage\SEQ For Each Loop Wrapper\FEL Simple Loop\SQL In FEL\OnPreExecute\SQL On Pre Execute for FEL SQL Task MyPackage\SEQ Top Level\SEQ Nested Lvl 1\SEQ Nested Lvl 2\SQL In Nested Lvl 2 MyPackage\SEQ Top Level\SEQ Nested Lvl 1\SQL In Nested Lvl 1 #1 MyPackage\SEQ Top Level\SEQ Nested Lvl 1\SQL In Nested Lvl 1 #2 6 matching tasks found in package. The full project and code is available for download below, but first we can walk through the project to highlight the most important sections of code. This code has been abbreviated for this description, but is complete in the download. First of all we load the package, and then start by looking at the Executables for the package. // Load the package file Application application = new Application(); using (Package package = application.LoadPackage(filename, null)) { int matchCount = 0; // Look in the package's executables ProcessExecutables(package.Executables, ref matchCount); ... // // ... // Write out final count Console.WriteLine("{0} matching tasks found in package.", matchCount); } The ProcessExecutables method is a key method, as an executable could be described as the the highest level of a working functionality or container. There are several of types of executables, such as tasks, or sequence containers and loops. To know what to do next we need to work out what type of executable we are dealing with as the abbreviated version of method shows below. private static void ProcessExecutables(Executables executables, ref int matchCount) { foreach (Executable executable in executables) { TaskHost taskHost = executable as TaskHost; if (taskHost != null) { ProcessTaskHost(taskHost, ref matchCount); ProcessEventHandlers(taskHost.EventHandlers, ref matchCount); continue; } ... // // ... ForEachLoop forEachLoop = executable as ForEachLoop; if (forEachLoop != null) { ProcessExecutables(forEachLoop.Executables, ref matchCount); ProcessEventHandlers(forEachLoop.EventHandlers, ref matchCount); continue; } } } As you can see if the executable we find is a task we then call out to our ProcessTaskHost method. As with all of our executables a task can have event handlers which themselves contain more executables such as task and loops, so we also make a call out our ProcessEventHandlers method. The other types of executables such as loops can also have event handlers as well as executables. As shown with the example for the ForEachLoop we call the same ProcessExecutables and ProcessEventHandlers methods again to drill down into the hierarchy of objects that the package may contain. This code needs to explicitly check for each type of executable (TaskHost, Sequence, ForLoop and ForEachLoop) because whilst they all have an Executables property this is not from a common base class or interface. This example was just a simple find a task by its name, so ProcessTaskHost really just does that. We also get the hierarchy of objects so we can write out for information, obviously you can adapt this method to do something more interesting such as adding a property expression. private static void ProcessTaskHost(TaskHost taskHost, ref int matchCount) { if (taskHost == null) { return; } // Check if the task matches our match name if (taskHost.Name.StartsWith(TaskNameFilter, StringComparison.OrdinalIgnoreCase)) { // Build up the full object hierarchy of the task // so we can write it out for information StringBuilder path = new StringBuilder(); DtsContainer container = taskHost; while (container != null) { path.Insert(0, container.Name); container = container.Parent; if (container != null) { path.Insert(0, "\\"); } } // Write the task path // e.g. Package\Container\Event\Task Console.WriteLine(path); Console.WriteLine(); // Increment match counter for info matchCount++; } } Just for completeness, the other processing method we covered above is for event handlers, but really that just calls back to the executables. This same method is called in our main package method, but it was omitted for brevity here. private static void ProcessEventHandlers(DtsEventHandlers eventHandlers, ref int matchCount) { foreach (DtsEventHandler eventHandler in eventHandlers) { ProcessExecutables(eventHandler.Executables, ref matchCount); } } As hopefully the code demonstrates, executables (Microsoft.SqlServer.Dts.Runtime.Executable) are the workers, but within them you can nest more executables (except for task tasks).Executables themselves can have event handlers which can in turn hold more executables. I have tried to illustrate this highlight the relationships in the following diagram. Download Sample code project TaskSearch.zip (11KB)

    Read the article

  • android Emulator always stop at "waiting for Home..."

    - by wuwupp
    hi,there, I freshed install Eclipse, jdk, android sdk 1.5 in winxp. but when I run the "hello world" app, the emulator always stop at "andorid" loading message. In eclipse console, it shows "waiting for HOME..." and in DDMS LogCat, it shows following msg: there are some error and warning. So, what's wrong with my case? I have googled lots of results, but no one can help me. Please help me. Many thx 06-13 00:07:54.323: INFO/DEBUG(551): debuggerd: Jun 30 2009 17:00:51 06-13 00:07:54.383: INFO/vold(550): Android Volume Daemon version 2.0 06-13 00:07:54.724: ERROR/flash_image(556): can't find recovery partition 06-13 00:07:55.223: DEBUG/qemud(558): entering main loop 06-13 00:07:55.323: DEBUG/qemud(558): multiplexer_handle_control: unknown control message (18 bytes): 'ko:unknown command' 06-13 00:07:55.493: INFO/vold(550): New MMC card 'SU02G' (serial 1012966) added @ /devices/platform/goldfish_mmc.0/mmc_host/mmc0/mmc0:e118 06-13 00:07:55.773: INFO/vold(550): Disk (blkdev 179:0), 262144 secs (128 MB) 0 partitions 06-13 00:07:55.773: INFO/vold(550): New blkdev 179.0 on media SU02G, media path /devices/platform/goldfish_mmc.0/mmc_host/mmc0/mmc0:e118, Dpp 0 06-13 00:07:55.814: INFO/vold(550): Evaluating dev '/devices/platform/goldfish_mmc.0/mmc_host/mmc0/mmc0:e118/block/mmcblk0' for mountable filesystems for '/sdcard' 06-13 00:07:56.014: ERROR/vold(550): Error opening switch name path '/sys/class/switch/test2' (No such file or directory) 06-13 00:07:56.014: ERROR/vold(550): Error bootstrapping switch '/sys/class/switch/test2' (m) 06-13 00:07:56.073: ERROR/vold(550): Error opening switch name path '/sys/class/switch/test' (No such file or directory) 06-13 00:07:56.073: ERROR/vold(550): Error bootstrapping switch '/sys/class/switch/test' (m) 06-13 00:07:56.073: DEBUG/vold(550): Bootstrapping complete 06-13 00:07:56.743: INFO//system/bin/dosfsck(550): dosfsck 3.0.1 (23 Nov 2008) 06-13 00:07:56.753: INFO//system/bin/dosfsck(550): dosfsck 3.0.1, 23 Nov 2008, FAT32, LFN 06-13 00:07:56.783: INFO//system/bin/dosfsck(550): Checking we can access the last sector of the filesystem 06-13 00:07:56.893: INFO//system/bin/dosfsck(550): Boot sector contents: 06-13 00:07:56.924: INFO//system/bin/dosfsck(550): System ID "MSWIN4.1" 06-13 00:07:56.934: INFO//system/bin/dosfsck(550): Media byte 0xf8 (hard disk) 06-13 00:07:56.953: INFO//system/bin/dosfsck(550): 512 bytes per logical sector 06-13 00:07:56.974: INFO//system/bin/dosfsck(550): 512 bytes per cluster 06-13 00:07:57.005: INFO//system/bin/dosfsck(550): 32 reserved sectors 06-13 00:07:57.013: INFO//system/bin/dosfsck(550): First FAT starts at byte 16384 (sector 32) 06-13 00:07:57.013: INFO//system/bin/dosfsck(550): 2 FATs, 32 bit entries 06-13 00:07:57.023: INFO//system/bin/dosfsck(550): 1040384 bytes per FAT (= 2032 sectors) 06-13 00:07:57.043: INFO//system/bin/dosfsck(550): Root directory start at cluster 2 (arbitrary size) 06-13 00:07:57.043: INFO//system/bin/dosfsck(550): Data area starts at byte 2097152 (sector 4096) 06-13 00:07:57.043: INFO//system/bin/dosfsck(550): 258048 data clusters (132120576 bytes) 06-13 00:07:57.103: INFO//system/bin/dosfsck(550): 9 sectors/track, 2 heads 06-13 00:07:57.103: INFO//system/bin/dosfsck(550): 0 hidden sectors 06-13 00:07:57.123: INFO//system/bin/dosfsck(550): 262144 sectors total 06-13 00:07:57.313: DEBUG/qemud(558): fdhandler_accept_event: accepting on fd 10 06-13 00:07:57.313: DEBUG/qemud(558): created client 0xe078 listening on fd 8 06-13 00:07:57.313: DEBUG/qemud(558): fdhandler_event: disconnect on fd 8 06-13 00:07:57.623: DEBUG/qemud(558): fdhandler_accept_event: accepting on fd 10 06-13 00:07:57.623: DEBUG/qemud(558): created client 0xf028 listening on fd 8 06-13 00:07:57.643: DEBUG/qemud(558): client_fd_receive: attempting registration for service 'gsm' 06-13 00:07:57.763: DEBUG/qemud(558): client_fd_receive: - received channel id 1 06-13 00:08:12.553: INFO//system/bin/dosfsck(550): Checking for unused clusters. 06-13 00:08:13.483: INFO//system/bin/dosfsck(550): Checking free cluster summary. 06-13 00:08:13.643: DEBUG/AndroidRuntime(553): AndroidRuntime START <<<<<<<<<<<<<< 06-13 00:08:13.705: DEBUG/AndroidRuntime(553): CheckJNI is ON 06-13 00:08:13.793: INFO//system/bin/dosfsck(550): /dev/block//vold/179:0: 0 files, 1/258048 clusters 06-13 00:08:14.063: INFO/logwrapper(550): /system/bin/dosfsck terminated by exit(0) 06-13 00:08:14.143: DEBUG/vold(550): Filesystem check completed OK 06-13 00:08:14.683: INFO/vold(550): Sucessfully mounted vfat filesystem 179:0 on /sdcard (safe-mode on) 06-13 00:08:17.023: INFO/(554): ServiceManager: 0xac38 06-13 00:08:17.883: INFO/AudioFlinger(554): AudioFlinger's thread ready to run for output 0 06-13 00:08:18.163: INFO/CameraService(554): CameraService started: pid=554 06-13 00:08:21.824: DEBUG/AndroidRuntime(553): --- registering native functions --- 06-13 00:08:27.813: INFO/Zygote(553): Preloading classes... 06-13 00:08:27.994: DEBUG/dalvikvm(553): GC freed 764 objects / 42216 bytes in 88ms 06-13 00:08:30.234: DEBUG/dalvikvm(553): GC freed 278 objects / 17160 bytes in 48ms 06-13 00:08:33.094: DEBUG/dalvikvm(553): GC freed 208 objects / 12696 bytes in 44ms 06-13 00:08:34.343: DEBUG/dalvikvm(553): Trying to load lib /system/lib/libmedia_jni.so 0x0 06-13 00:08:35.803: DEBUG/dalvikvm(553): Added shared lib /system/lib/libmedia_jni.so 0x0 06-13 00:08:35.903: DEBUG/dalvikvm(553): Trying to load lib /system/lib/libmedia_jni.so 0x0 06-13 00:08:35.903: DEBUG/dalvikvm(553): Shared lib '/system/lib/libmedia_jni.so' already loaded in same CL 0x0 06-13 00:08:36.003: DEBUG/dalvikvm(553): Trying to load lib /system/lib/libmedia_jni.so 0x0 06-13 00:08:36.003: DEBUG/dalvikvm(553): Shared lib '/system/lib/libmedia_jni.so' already loaded in same CL 0x0 06-13 00:08:36.215: DEBUG/dalvikvm(553): Trying to load lib /system/lib/libmedia_jni.so 0x0 06-13 00:08:36.244: DEBUG/dalvikvm(553): Shared lib '/system/lib/libmedia_jni.so' already loaded in same CL 0x0 06-13 00:08:36.455: DEBUG/dalvikvm(553): GC freed 462 objects / 29144 bytes in 70ms 06-13 00:08:44.123: DEBUG/dalvikvm(553): GC freed 3584 objects / 171648 bytes in 125ms 06-13 00:09:10.473: DEBUG/dalvikvm(553): GC freed 11329 objects / 400856 bytes in 196ms 06-13 00:09:17.373: DEBUG/dalvikvm(553): GC freed 10472 objects / 438272 bytes in 199ms 06-13 00:09:24.563: DEBUG/dalvikvm(553): GC freed 10975 objects / 459800 bytes in 202ms 06-13 00:09:46.403: DEBUG/dalvikvm(553): GC freed 14372 objects / 506896 bytes in 252ms 06-13 00:09:53.793: DEBUG/dalvikvm(553): GC freed 11314 objects / 481360 bytes in 215ms 06-13 00:09:57.743: DEBUG/dalvikvm(553): GC freed 5928 objects / 248640 bytes in 195ms 06-13 00:10:01.324: DEBUG/dalvikvm(553): GC freed 349 objects / 37032 bytes in 190ms 06-13 00:10:05.253: DEBUG/dalvikvm(553): GC freed 778 objects / 48376 bytes in 217ms 06-13 00:10:06.564: DEBUG/dalvikvm(553): GC freed 321 objects / 37288 bytes in 219ms 06-13 00:10:08.194: DEBUG/dalvikvm(553): GC freed 477 objects / 29584 bytes in 212ms 06-13 00:10:08.663: DEBUG/dalvikvm(553): Trying to load lib /system/lib/libwebcore.so 0x0 06-13 00:10:09.743: DEBUG/dalvikvm(553): Added shared lib /system/lib/libwebcore.so 0x0 06-13 00:10:11.634: DEBUG/dalvikvm(553): GC freed 441 objects / 26224 bytes in 236ms 06-13 00:10:12.893: DEBUG/dalvikvm(553): GC freed 506 objects / 41464 bytes in 235ms 06-13 00:10:14.153: DEBUG/dalvikvm(553): GC freed 537 objects / 38832 bytes in 239ms 06-13 00:10:15.883: DEBUG/dalvikvm(553): GC freed 342 objects / 22552 bytes in 248ms 06-13 00:10:17.124: DEBUG/dalvikvm(553): GC freed 338 objects / 18736 bytes in 264ms 06-13 00:10:18.523: DEBUG/dalvikvm(553): GC freed 629 objects / 32136 bytes in 260ms 06-13 00:10:38.933: DEBUG/dalvikvm(553): GC freed 14257 objects / 497280 bytes in 368ms 06-13 00:10:46.453: DEBUG/dalvikvm(553): GC freed 11164 objects / 469576 bytes in 360ms 06-13 00:10:52.973: DEBUG/dalvikvm(553): GC freed 7134 objects / 311432 bytes in 339ms 06-13 00:10:55.595: DEBUG/dalvikvm(553): GC freed 752 objects / 43224 bytes in 520ms 06-13 00:10:56.863: DEBUG/dalvikvm(553): GC freed 598 objects / 31496 bytes in 307ms 06-13 00:10:58.543: DEBUG/dalvikvm(553): GC freed 413 objects / 26336 bytes in 355ms 06-13 00:10:59.263: INFO/Zygote(553): ...preloaded 1166 classes in 151403ms. 06-13 00:10:59.683: DEBUG/dalvikvm(553): GC freed 313 objects / 19952 bytes in 343ms 06-13 00:10:59.793: INFO/Zygote(553): Preloading resources... 06-13 00:11:00.683: DEBUG/dalvikvm(553): GC freed 54 objects / 11248 bytes in 340ms 06-13 00:11:05.723: DEBUG/dalvikvm(553): GC freed 337 objects / 15008 bytes in 317ms 06-13 00:11:08.703: DEBUG/dalvikvm(553): GC freed 280 objects / 11768 bytes in 312ms 06-13 00:11:09.303: INFO/Zygote(553): ...preloaded 48 resources in 9513ms. 06-13 00:11:09.795: INFO/Zygote(553): ...preloaded 15 resources in 454ms. 06-13 00:11:10.303: DEBUG/dalvikvm(553): GC freed 118 objects / 8616 bytes in 420ms 06-13 00:11:10.913: DEBUG/dalvikvm(553): GC freed 205 objects / 8104 bytes in 308ms 06-13 00:11:11.344: DEBUG/dalvikvm(553): GC freed 36 objects / 1400 bytes in 320ms 06-13 00:11:11.543: INFO/dalvikvm(553): Splitting out new zygote heap 06-13 00:11:12.973: INFO/dalvikvm(553): System server process 585 has been created 06-13 00:11:13.336: INFO/Zygote(553): Accepting command socket connections 06-13 00:11:14.963: INFO/jdwp(585): received file descriptor 10 from ADB 06-13 00:11:16.843: WARN/System.err(585): Can't dispatch DDM chunk 46454154: no handler defined 06-13 00:11:16.953: WARN/System.err(585): Can't dispatch DDM chunk 4d505251: no handler defined 06-13 00:11:17.763: DEBUG/dalvikvm(585): Trying to load lib /system/lib/libandroid_servers.so 0x0 06-13 00:11:19.714: DEBUG/dalvikvm(585): Added shared lib /system/lib/libandroid_servers.so 0x0 06-13 00:11:20.123: INFO/sysproc(585): Entered system_init() 06-13 00:11:20.223: INFO/sysproc(585): ServiceManager: 0x1017b8 06-13 00:11:20.359: INFO/SurfaceFlinger(585): SurfaceFlinger is starting 06-13 00:11:20.493: INFO/SurfaceFlinger(585): SurfaceFlinger's main thread ready to run. Initializing graphics H/W... 06-13 00:11:20.634: ERROR/MemoryHeapBase(585): error opening /dev/pmem: No such file or directory 06-13 00:11:20.704: ERROR/SurfaceFlinger(585): Couldn't open /sys/power/wait_for_fb_sleep or /sys/power/wait_for_fb_wake 06-13 00:11:22.013: ERROR/GLLogger(585): couldn't load library (Cannot find library) 06-13 00:11:22.103: INFO/SurfaceFlinger(585): EGL informations: 06-13 00:11:22.113: INFO/SurfaceFlinger(585): # of configs : 6 06-13 00:11:22.123: INFO/SurfaceFlinger(585): vendor : Android 06-13 00:11:22.123: INFO/SurfaceFlinger(585): version : 1.31 Android META-EGL 06-13 00:11:22.134: INFO/SurfaceFlinger(585): extensions: 06-13 00:11:22.134: INFO/SurfaceFlinger(585): Client API: OpenGL ES 06-13 00:11:22.193: INFO/EGLDisplaySurface(585): using (fd=22) 06-13 00:11:22.193: INFO/EGLDisplaySurface(585): id = 06-13 00:11:22.193: INFO/EGLDisplaySurface(585): xres = 320 px 06-13 00:11:22.193: INFO/EGLDisplaySurface(585): yres = 480 px 06-13 00:11:22.193: INFO/EGLDisplaySurface(585): xres_virtual = 320 px 06-13 00:11:22.193: INFO/EGLDisplaySurface(585): yres_virtual = 960 px 06-13 00:11:22.193: INFO/EGLDisplaySurface(585): bpp = 16 06-13 00:11:22.193: INFO/EGLDisplaySurface(585): r = 11:5 06-13 00:11:22.193: INFO/EGLDisplaySurface(585): g = 5:6 06-13 00:11:22.193: INFO/EGLDisplaySurface(585): b = 0:5 06-13 00:11:22.193: INFO/EGLDisplaySurface(585): width = 49 mm (165.877548 dpi) 06-13 00:11:22.193: INFO/EGLDisplaySurface(585): height = 74 mm (164.756760 dpi) 06-13 00:11:22.193: INFO/EGLDisplaySurface(585): refresh rate = 60.00 Hz 06-13 00:11:22.533: WARN/HAL(585): load: module=/system/lib/hw/copybit.goldfish.so error=Cannot find library 06-13 00:11:22.543: WARN/HAL(585): load: module=/system/lib/hw/copybit.default.so error=Cannot find library 06-13 00:11:22.553: WARN/SurfaceFlinger(585): ro.sf.lcd_density not defined, using 160 dpi by default. 06-13 00:11:22.644: INFO/SurfaceFlinger(585): OpenGL informations: 06-13 00:11:22.654: INFO/SurfaceFlinger(585): vendor : Android 06-13 00:11:22.654: INFO/SurfaceFlinger(585): renderer : Android PixelFlinger 1.0 06-13 00:11:22.654: INFO/SurfaceFlinger(585): version : OpenGL ES-CM 1.0 06-13 00:11:22.654: INFO/SurfaceFlinger(585): extensions: GL_OES_byte_coordinates GL_OES_fixed_point GL_OES_single_precision GL_OES_read_format GL_OES_compressed_paletted_texture GL_OES_draw_texture GL_OES_matrix_get GL_OES_query_matrix GL_ARB_texture_compression GL_ARB_texture_non_power_of_two GL_ANDROID_direct_texture GL_ANDROID_user_clip_plane GL_ANDROID_vertex_buffer_object GL_ANDROID_generate_mipmap 06-13 00:11:22.673: WARN/HAL(585): load: module=/system/lib/hw/copybit.goldfish.so error=Cannot find library 06-13 00:11:22.683: WARN/HAL(585): load: module=/system/lib/hw/copybit.default.so error=Cannot find library 06-13 00:11:22.703: WARN/HAL(585): load: module=/system/lib/hw/overlay.goldfish.so error=Cannot find library 06-13 00:11:22.713: WARN/HAL(585): load: module=/system/lib/hw/overlay.default.so error=Cannot find library 06-13 00:11:23.663: INFO/sysproc(585): System server: starting Android runtime. 06-13 00:11:23.733: INFO/sysproc(585): System server: starting Android services. 06-13 00:11:23.953: INFO/SystemServer(585): Entered the Android system server! 06-13 00:11:24.303: INFO/sysproc(585): System server: entering thread pool. 06-13 00:11:24.763: ERROR/GLLogger(585): couldn't load library (Cannot find library) 06-13 00:11:25.893: INFO/ARMAssembler(585): generated scanline__00000077:03545404_00000A01_00000000 [ 30 ipp] (51 ins) at [0x18f708:0x18f7d4] in 72796961 ns 06-13 00:11:26.193: INFO/SystemServer(585): Starting Power Manager. 06-13 00:11:26.953: INFO/SystemServer(585): Starting Activity Manager. 06-13 00:11:31.733: INFO/SystemServer(585): Starting telephony registry 06-13 00:11:32.054: INFO/SystemServer(585): Starting Package Manager. 06-13 00:11:32.553: INFO/Installer(585): connecting... 06-13 00:11:32.914: INFO/installd(555): new connection 06-13 00:11:35.193: INFO/PackageManager(585): Got library android.awt in /system/framework/android.awt.jar 06-13 00:11:35.313: INFO/PackageManager(585): Got library android.test.runner in /system/framework/android.test.runner.jar 06-13 00:11:35.324: INFO/PackageManager(585): Got library com.android.im.plugin in /system/framework/com.android.im.plugin.jar 06-13 00:11:44.643: DEBUG/PackageManager(585): Scanning app dir /system/framework 06-13 00:11:49.513: DEBUG/PackageManager(585): Scanning app dir /system/app 06-13 00:11:51.493: DEBUG/dalvikvm(585): GC freed 6088 objects / 251280 bytes in 1237ms 06-13 00:12:27.497: DEBUG/dalvikvm(585): GC freed 3435 objects / 216088 bytes in 792ms 06-13 00:12:29.213: DEBUG/PackageManager(585): Scanning app dir /data/app 06-13 00:12:30.223: DEBUG/PackageManager(585): Scanning app dir /data/app-private 06-13 00:12:30.425: INFO/PackageManager(585): Time to scan packages: 47.319 seconds 06-13 00:12:30.703: WARN/PackageManager(585): Unknown permission com.google.android.googleapps.permission.GOOGLE_AUTH in package com.android.providers.contacts 06-13 00:12:30.803: WARN/PackageManager(585): Unknown permission com.google.android.googleapps.permission.GOOGLE_AUTH.cp in package com.android.providers.contacts 06-13 00:12:30.853: WARN/PackageManager(585): Unknown permission com.google.android.googleapps.permission.GOOGLE_AUTH in package com.android.development 06-13 00:12:30.913: WARN/PackageManager(585): Unknown permission com.google.android.googleapps.permission.GOOGLE_AUTH.ALL_SERVICES in package com.android.development 06-13 00:12:31.133: WARN/PackageManager(585): Unknown permission com.google.android.googleapps.permission.GOOGLE_AUTH.YouTubeUser in package com.android.development 06-13 00:12:31.143: WARN/PackageManager(585): Unknown permission com.google.android.googleapps.permission.ACCESS_GOOGLE_PASSWORD in package com.android.development 06-13 00:12:31.234: WARN/PackageManager(585): Unknown permission com.google.android.providers.gmail.permission.WRITE_GMAIL in package com.android.settings 06-13 00:12:31.254: WARN/PackageManager(585): Unknown permission com.google.android.providers.gmail.permission.READ_GMAIL in package com.android.settings 06-13 00:12:31.303: WARN/PackageManager(585): Unknown permission com.google.android.googleapps.permission.GOOGLE_AUTH in package com.android.settings 06-13 00:12:31.683: WARN/PackageManager(585): Unknown permission com.google.android.googleapps.permission.GOOGLE_AUTH in package com.android.browser 06-13 00:12:31.803: WARN/PackageManager(585): Unknown permission com.google.android.googleapps.permission.GOOGLE_AUTH.mail in package com.android.contacts 06-13 00:12:34.603: DEBUG/dalvikvm(585): GC freed 2851 objects / 161304 bytes in 845ms 06-13 00:12:35.403: INFO/SystemServer(585): Starting Content Manager. 06-13 00:12:39.954: WARN/ActivityManager(585): Unable to start service Intent { action=android.accounts.IAccountsService comp={com.google.android.googleapps/com.google.android.googleapps.GoogleLoginService} }: not found 06-13 00:12:40.063: WARN/AccountMonitor(585): Couldn't connect to Intent { action=android.accounts.IAccountsService comp={com.google.android.googleapps/com.google.android.googleapps.GoogleLoginService} } (Missing service?) 06-13 00:12:40.253: INFO/SystemServer(585): Starting System Content Providers. 06-13 00:12:40.553: INFO/ActivityThread(585): Publishing provider settings: com.android.providers.settings.SettingsProvider 06-13 00:12:41.433: INFO/ActivityThread(585): Publishing provider sync: android.content.SyncProvider 06-13 00:12:41.683: INFO/SystemServer(585): Starting Battery Service. 06-13 00:12:42.293: ERROR/BatteryService(585): Could not open '/sys/class/power_supply/usb/online' 06-13 00:12:42.433: ERROR/BatteryService(585): Could not open '/sys/class/power_supply/battery/batt_vol' 06-13 00:12:42.543: ERROR/BatteryService(585): Could not open '/sys/class/power_supply/battery/batt_temp' 06-13 00:12:42.933: INFO/SystemServer(585): Starting Hardware Service. 06-13 00:12:43.398: DEBUG/qemud(558): fdhandler_accept_event: accepting on fd 10 06-13 00:12:43.623: DEBUG/qemud(558): created client 0x10fd8 listening on fd 11 06-13 00:12:43.743: DEBUG/qemud(558): client_fd_receive: attempting registration for service 'hw-control' 06-13 00:12:43.873: DEBUG/qemud(558): client_fd_receive: - received channel id 2 06-13 00:15:20.695: WARN/SurfaceFlinger(585): executeScheduledBroadcasts() skipped, contention on the client. We'll try again later...

    Read the article

  • Taking advantage of Windows Azure CDN and Dynamic Pages in ASP.NET - Caching content from hosted services

    - by Shawn Cicoria
    With the updates to Windows Azure CDN announced this week [1] I wanted to help illustrate the capability with a working sample that will serve up dynamic content from an ASP.NET site hosted in a WebRole. First, to get a good overview of the capability you can read the Overview of the Windows Azure CDN [2] content on MSDN. When you setup the ability to cache content from a hosted service, the requirement is to provide a path to your role’s DNS endpoint that ends in the path “/cdn”.  Additionally, you then map CDN to that service. What WAZ CDN does, is allow you to then map that through the CDN to your host.  The CDN will then make a request to your host on your client’s behalf. The requirement is still that your client, and any Url’s that are to be serviced through the CDN and this capability have to use the CDN DNS name and not your host – no different than what CDN does for Blog storage. The following 2 URL’s are samples of how the client needs to issue the requests. Windows Azure hosted service URL: http: //myHostedService.cloudapp.net/cdn/music.aspx   - for regular “dynamic” content Windows Azure CDN URL: http: //<identifier>.vo.msecnd.net/music.aspx   - for CDN “cachable” content. The first URL path’s the request direct to your host into the Azure datacenter.  The 2nd URL paths the request through the CDN infrastructure, where CDN will make the determination to request the content on behalf of the client to the Azure datacenter and your host on the /cdn path. The big advantage here is you can apply logic to your content creation.  What’s important is emitting the CDN friendly headers that allow CDN to request and re-request only when you designate based upon it’s rules of “staleness” as described in the overview page. With IIS7.5 there is an underlying issue when the Managed Module “OutputCache” is enabled that in order to emit a good header for your content, you’ll need to remove, and in my sample, helps provide CDN friendly headers.  You get IIS 7.5 when running under OS Family “2” in your service configuration. By default, and when the OutputCache managed module is loaded, if you use the HttpResponse.CachePolicy to set the Http Headers for “max-age” when the HttpCacheability is “Public”, you will NOT get the “max-age” emitted as part of the “Cache-control:” header.  Instead, the OutputCache module will remove “max-age” and just emit “public”.  It works ok when Cacheability is set to “private”. To work around the issue and ensure your code as follows emits the full max-age along with the public option, you need to remove as follows: <system.webServer>   <modules runAllManagedModulesForAllRequests="true">     <remove name="OutputCache"/>   </modules> </system.webServer>   Response.Cache.SetCacheability(HttpCacheability.Public); Response.Cache.SetMaxAge(TimeSpan.FromMinutes(rv));   In the attached solution, the way I approached it was to have a VirtualApplication under the root site that has it’s own web.config  - this VirtualApplication is the /cdn of the site and when deployed to Azure as a Web Role will surface as a distinct IIS Application – along with a separate AppDomain. The CDN Sample is a simple Web Forms site that the /default landing page contains 3 IFrames to host: 1. Content direct from the host @   http://xxxx.cloudapp.net/cdn 2. Content via the CDN @ http://azxxx.vo.msecnd.net  3. Simple list of recent requests – showing where the request came from.   When you run the sample the first time you hit the page, both the Host and the CDN will cause 2 initial requests to hit the host.  You won’t see the first requests in the list because of timing – but if you refresh, you’ll see that the list will show that you have 2 requests initially. 1. sourced direct from the Browser to the HOST 2. sourced via the CDN The picture above shows the call-outs of each of those requests – green rows showing requests coming direct to the HOST, yellow showing the CDN request.  The IP addresses of the green items are direct from the client, where the CDN is from the CDN data center. As you refresh the page (hit Ctrl+F5 to force a full refresh and avoid “304 – not changed”) you’ll see that the request to the HOST get’s processed direct; but the request to the CDN endpoint is serviced direct from the CDN and doesn’t incur any additional request back to the HOST. The following is the Headers from the CDN response (Status-Line) HTTP/1.1 200 OK Age 13 Cache-Control public, max-age=300 Connection keep-alive Content-Length 6212 Content-Type image/jpeg; charset=utf-8 Date Fri, 11 Mar 2011 20:47:14 GMT Expires Fri, 11 Mar 2011 20:52:01 GMT Last-Modified Fri, 11 Mar 2011 20:47:02 GMT Server Microsoft-IIS/7.5 X-AspNet-Version 4.0.30319 X-Powered-By ASP.NET   The following are the Headers from the HOST response (Status-Line) HTTP/1.1 200 OK Cache-Control public, max-age=300 Content-Length 6189 Content-Type image/jpeg; charset=utf-8 Date Fri, 11 Mar 2011 20:47:15 GMT Last-Modified Fri, 11 Mar 2011 20:47:02 GMT Server Microsoft-IIS/7.5 X-AspNet-Version 4.0.30319 X-Powered-By ASP.NET   You can see that with the CDN request, the countdown (age) starts for aging the content. The full sample is located here: CDNSampleSite.zip [1] http://blogs.msdn.com/b/windowsazure/archive/2011/03/09/now-available-updated-windows-azure-sdk-and-windows-azure-management-portal.aspx [2] http://msdn.microsoft.com/en-us/library/ff919703.aspx

    Read the article

  • Protecting offline IRM rights and the error "Unable to Connect to Offline database"

    - by Simon Thorpe
    One of the most common problems I get asked about Oracle IRM is in relation to the error message "Unable to Connect to Offline database". This error message is a result of how Oracle IRM is protecting the cached rights on the local machine and if that cache has become invalid in anyway, this error is thrown. Offline rights and security First we need to understand how Oracle IRM handles offline use. The way it is implemented is one of the main reasons why Oracle IRM is the leading document security solution and demonstrates our methodology to ensure that solutions address both security and usability and puts the balance of these two in your control. Each classification has a set of predefined roles that the manager of the classification can assign to users. Each role has an offline period which determines the amount of time a user can access content without having to communicate with the IRM server. By default for the context model, which is the classification system that ships out of the box with Oracle IRM, the offline period for each role is 3 days. This is easily changed however and can be as low as under an hour to as long as years. It is also possible to switch off the ability to access content offline which can be useful when content is very sensitive and requires a tight leash. So when a user is online, transparently in the background, the Oracle IRM Desktop communicates with the server and updates the users rights and offline periods. This transparent synchronization period is determined by the server and communicated to all IRM Desktops and allows for users rights to be kept up to date without their intervention. This allows us to support some very important scenarios which are key to a successful IRM solution. A user doesn't have to make any decision when going offline, they simply unplug their laptop and they already have their offline periods synchronized to the maximum values. Any solution that requires a user to make a decision at the point of going offline isn't going to work because people forget to do this and will therefore be unable to legitimately access their content offline. If your rights change to REMOVE your access to content, this also happens in the background. This is very useful when someone has an offline duration of a week and they happen to make a connection to the internet 3 days into that offline period, the Oracle IRM Desktop detects this online state and automatically updates all rights for the user. This means the business risk is reduced when setting long offline periods, because of the daily transparent sync, you can reflect changes as soon as the user is online. Of course, if they choose not to come online at all during that week offline period, you cannot effect change, but you take that risk in giving the 7 day offline period in the first place. If you are added to a NEW classification during the day, this will automatically be synchronized without the user even having to open a piece of content secured against that classification. This is very important, consider the scenario where a senior executive downloads all their email but doesn't open any of it. Disconnects the laptop and then gets on a plane. During the flight they attempt to open a document attached to a downloaded email which has been secured against an IRM classification the user was not even aware they had access to. Because their new role in this classification was automatically synchronized their experience is a good one and the document opens. More information on how the Oracle IRM classification model works can be found in this article by Martin Abrahams. So what about problems accessing the offline rights database? So onto the core issue... when these rights are cached to your machine they are stored in an encrypted database. The encryption of this offline database is keyed to the instance of the installation of the IRM Desktop and the Windows user account. Why? Well what you do not want to happen is for someone to get their rights for content and then copy these files across hundreds of other machines, therefore getting access to sensitive content across many environments. The IRM server has a setting which controls how many times you can cache these rights on unique machines. This is because people typically access IRM content on more than one computer. Their work desktop, a laptop and often a home computer. So Oracle IRM allows for the usability of caching rights on more than one computer whilst retaining strong security over this cache. So what happens if these files are corrupted in someway? That's when you will see the error, Unable to Connect to Offline database. The most common instance of seeing this is when you are using virtual machines and copy them from one computer to the next. The virtual machine software, VMWare Workstation for example, makes changes to the unique information of that virtual machine and as such invalidates the offline database. How do you solve the problem? Resolution is however simple. You just delete all of the offline database files on the machine and they will be recreated with working encryption when the Oracle IRM Desktop next starts. However this does mean that the IRM server will think you have your rights cached to more than one computer and you will need to rerequest your rights, even though you are only going to be accessing them on one. Because it still thinks the old cache is valid. So be aware, it is good practice to increase the server limit from the default of 1 to say 3 or 4. This is done using the Enterprise Manager instance of IRM. So to delete these offline files I have a simple .bat file you can use; Download DeleteOfflineDBs.bat Note that this uses pskillto stop the irmBackground.exe from running. This is part of the IRM Desktop and holds open a lock to the offline database. Either kill this from task manager or use pskillas part of the script.

    Read the article

  • XNA Notes 011

    - by George Clingerman
    Even with a lot of the XNA community working on Dream Build Play entries ( I swear I’m going to finish mine this year!) people are still finding time to do side projects and be amazingly active in the XNA and XBLIG community. With my one eye on my code and one eye on the community, here’s what I noticed these over achievers doing this past week! Time Critical XNA News: Xbox LIVE Indie Games sales data will be delayed March 17-20th due to some schedule maintenance http://create.msdn.com/en-us/news/indie_games_data_delay_march2011 GameMarx is releasing a series of videos to help raise donations for victims of the earthquakes and tsunami in Japan. Help out if you can! http://www.gamemarx.com/video/special/29/help-japan-sushido.aspx XNA MVPs: Catalin Zima shares his thoughts on the MVP summit and my book! http://www.catalinzima.com/2011/03/mvp-summit-2011/ Glenn Wilson (@mykre) helps the XNA team announce some new educational content that you don’t want to miss if you’re porting your app or game to Windows Phone 7 http://www.virtualrealm.com.au/Blog/tabid/62/EntryId/653/Porting-your-App-or-Game-to-Windows-Phone-7.aspx and Windows Phone 7 from scratch http://www.virtualrealm.com.au/Blog/tabid/62/EntryId/654/Windows-Phone-from-Scratch.aspx and shares a link to some free architectural models and textures http://twitter.com/#!/Mykre/status/46410160784158720 George (that’s me!) shares his MVP Summit 2011 summary and XBLIG thoughts http://geekswithblogs.net/clingermangw/archive/2011/03/15/144366.aspx XNA Developers: @SmallCaveGames shares a Code of Ethics for Xbox LIVE Indie Game Developers http://smallcavegames.blogspot.com/2011/03/unofficial-xblig-developers-code-of.html Derek S adds more Xbox LIVE Indie Game studios to his master list of XBLIG links http://twitter.com/#!/Mr_Deeke/status/46140996056125440 http://xbl-indieverse.blogspot.com/p/xblig-links.html Making games and want to help kids? Then share your story with GameFace: America! http://gameitupinitiative.com/about-the-initiative/programs/gameface-america/ Xbox LIVE Indie Games (XBLIG): XonaGames shares some video footage of their booth from GDC 2011 Video 1: http://youtu.be/lxIV9nk3Gq4 Video 2: http://youtu.be/GgfrjqkxR_o Video 3: http://youtu.be/yVcpXrTX7SQ Joystiq on Mommy’s Best Games Serious Sam Double D http://www.joystiq.com/2011/03/16/the-most-important-thing-about-serious-sam-double-d/ And The Escapist recommends that gamers start learning to avoid cleavage now http://www.escapistmagazine.com/news/view/108543-Boobie-Bomber-Makes-First-Appearance-in-Serious-Sam-Double-D Magiko Gaming started a blog on the XBLIG dashboard daily Top 10 games in the US. Good way to go back in time and look at the history of which games were in the the Top 10. http://dailytop10indiegames.wordpress.com/ Where are they going now? XBLIG developers at a crossroads.. http://www.gamesetwatch.com/2011/03/where_are_they_going_now_xblig.php http://www.gamasutra.com/view/news/33527/InDepth_Where_Are_They_Going_Now_XBLIG_Developers_At_A_Crossroads_.php BinaryTweed’s Clover: A Curious Tail is Xbox LIVE’s Deal of the Week! http://www.armlessoctopus.com/2011/03/15/what-luck-clover-a-curious-tale-is-half-price-this-week/ Looking for an Xbox LIVE Indie Game to buy? Writings of Mass Deduction has over 125 suggestions at this point! http://writingsofmassdeduction.com/ SkaStudios shares Vampire Smile Achievements AND their PAX East 2011 Both Setup video http://www.ska-studios.com/2011/03/14/vampire-smile-achievement/ http://www.ska-studios.com/2011/03/15/pax-booth-setup-time-lapse/ MasterBlud and VVGTV starts a new community for XBLIG developers and gamers to join http://vvgtv.forumotion.com/ Raymond Matthews (@DrakstarMatryx) covers Mommy’s Best Games getting Serious http://www.darkstarmatryx.com/?p=286 XNA Development: Dave Henry (@mort8088) posts the 4th tutorial in his series XNA 4.0 SpriteBatch extended http://mort8088.com/2011/03/11/xna-4-0-tutorial-4-spritebatch-extended/ Tutorial 5 - Creating a manual blank texture http://mort8088.com/2011/03/13/xna-4-tutorial-5-manual-blank-texture/ XNA 4.0 Tutorial 6 - Spritesheet Object http://mort8088.com/2011/03/18/xna-4-0-tutorial-6-spritesheet-object/ Jason Mitchell shares a tutorial on setting the alpha value for spritebatch in XNA 4.0 http://www.jason-mitchell.com/index.php/2011/03/13/setting-alpha-value-for-spritebatch-draw-in-xna-4/ XNA for Silverlight Developers: Part 7 - Collision Detection http://www.silverlightshow.net/items/XNA-for-Silverlight-developers-Part-7-Collision-detection.aspx Markus Ewald (@Cygon4) shares the full Ninject 2.0 binding for XNA and Sunburn http://twitter.com/#!/Cygon4/status/48330203826622464 Michael B. McLaughlin shares an AccelerometerInput XNA GameComponent he created (which I’m probably going to snag for a game I’m working on...) http://geekswithblogs.net/mikebmcl/archive/2011/03/17/accelerometerinput-xna-gamecomponent.aspx Extra Credit tackles the building of a good tutorial. Must watch for all Indie game devs (thanks for pointing it out Evan Johnson!) http://twitter.com/#!/johnsonevan/status/48452115680604160 http://www.escapistmagazine.com/videos/view/extra-credits/2921-Tutorials-101 ExEn is fully funded at this point so definitely something for XBLIG developers to keep an eye on as they consider releasing their games on other platforms http://rockethub.com/projects/752-exen-xna-for-iphone-android-and-silverlight Channel 9 and Greg Duncan post Mixing the Game State Management and Platformer XNA Recipes http://channel9.msdn.com/coding4fun/blog/Mixing-the-Game-State-Management-and-Platformer-XNA-Recipes Sgt. Conker has noticed Mike McLaughlin has been crazy productive and has done a recap of his recent posts http://www.sgtconker.com/2011/03/recap-of-mikebmcls-posts/

    Read the article

  • Restore Your PC from Windows Home Server

    - by Mysticgeek
    If your computer crashes or you get a virus infection that makes it unrecoverable, doing a clean install can be a hassle, let alone getting your data back. If you’re backing up your computers to Windows Home Server, you can completely restore them to the last successful backup. Note: For this process to work you need to verify the PC you want to restore is connected to your network via Ethernet. If you have it connected wirelessly it won’t work. Restore a PC from Windows Home Server On the computer you want to restore, pop in the Windows Home Server Home Computer Restore disc and boot from it. If you don’t have one already made, you can easily make one following these instructions. We have also included the link to the restore disc below. Boot from the CD then select if your machine has 512MB or RAM or more. The disc will initialize… Then choose your language and keyboard settings. Hopefully if everything goes correctly, your network card will be detected and you can continue. However, if it doesn’t like in our example, click on the Show Details button. In the Detect Hardware screen click on the Install Drivers button. Now you will need to have a USB flash drive with the correct drivers on it. It has to be a flash drive or a floppy (if you happen to still have one of those) because you can’t take out the Restore CD. If you want to make sure you have the correct drivers on the USB flash drive, open the Windows Home Server Console on another computer on your network. In the Computers and Backup section right-click on the computer you want to restore and select View Backups. Select the backup you want to restore from and click the Open button in the Restore or view Files section. Now drag the entire contents of the folder named Windows Home Server Drivers for Restore to the USB flash drive. Back to the machine you’re trying to restore, insert the USB flash drive with the correct drivers and click the Scan button. Wait a few moments while the drivers are found then click Ok then Continue.   The Restore Computer Wizard starts up… Enter in your home server password and click Next. Select the computer you want to restore. If it isn’t selected by default you can pull it up from the dropdown list under Another Computer. Make certain you’re selecting the correct machine. Now select the backup you want to restore. In this example we only have one but chances are you’ll have several. If you have several backups to choose from, you might want to check out the details for them. Now you can select the disk from backup and and restore it to the destination volume. You might need to initialize a disk, change a drive letter, or other disk management tasks, if so, then click on Run Disk Manger. For example we want to change the destination drive letter to (C:).   After you’ve made all the changes to the destination disk you can continue with the restore process. If everything looks correct, confirm the restore configuration. If you need to make any changes at this point, you can still go back and make them. Now Windows Home Server will restore your drive. The amount of time it takes will vary depend on the amount of data you have to restore, network connection speed, and hardware. You are notified when the restore successfully completes. Click Finish and the PC will reboot and be restored and should be working correctly. All the updates, programs, and files will be back that were saved to the last successful backup. Anything you might have installed after that backup will be gone. If you have your computers set to backup every night, then hopefully it won’t be a big issue.   Conclusion Backing up the computers on your network to Windows Home Server is a valuable tool in your backup strategy. Sometimes you may only need to restore a couple files and we’ve covered how to restore them from backups on WHS and that works really well. If the unthinkable happens and you need to restore the entire computer, WHS makes that easy too.  Download Windows Home Server Home Computer Restore CD Similar Articles Productive Geek Tips Restore Files from Backups on Windows Home ServerCreate A Windows Home Server Home Computer Restore DiscGMedia Blog: Setting Up a Windows Home ServerShare Ubuntu Home Directories using SambaInstalling Windows Home Server TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Make your Joomla & Drupal Sites Mobile with OSMOBI Integrate Twitter and Delicious and Make Life Easier Design Your Web Pages Using the Golden Ratio Worldwide Growth of the Internet How to Find Your Mac Address Use My TextTools to Edit and Organize Text

    Read the article

  • Book Review: Oracle ADF Real World Developer’s Guide

    - by Frank Nimphius
    Recently PACKT Publishing published "Oracle ADF Real World Developer’s Guide" by Jobinesh Purushothaman, a product manager in our team. Though already the sixth book dedicated to Oracle ADF, it has a lot of great information in it that none of the previous books covered, making it a safe buy even for those who own the other books published by Oracle Press (McGrwHill) and PACKT Publishing. More than the half of the "Oracle ADF Real World Developer’s Guide" book is dedicated to Oracle ADF Business Components in a depth and clarity that allows you to feel the expertise that Jobinesh gained in this area. If you enjoy Jobinesh blog (http://jobinesh.blogspot.co.uk/) about Oracle ADF, then, no matter what expert you are in Oracle ADF, this book makes you happy as it provides you with detail information you always wished to have. If you are new to Oracle ADF, then this book alone doesn't get you flying, but, if you have some Java background, accelerates your learning big, big, big times. Chapter 1 is an introduction to Oracle ADF and not only explains the layers but also how it compares to plain Java EE solutions (page 13). If you are new to Oracle JDeveloper and ADF, then at the end of this chapter you know how to start JDeveloper and begin your ADF development Chapter 2 starts with what Jobinesh really is good at: ADF Business Components. In this chapter you learn about the architecture ingredients of ADF Business Components: View Objects, View Links, Associations, Entities, Row Sets, Query Collections and Application Modules. This chapter also provides a introduction to ADFBC SDO services, as well as sequence diagrams for what happens when you execute queries or commit updates. Chapter 3 is dedicated to entity objects and  is one of many chapters in this book you will enjoy and never want to miss. Jobinesh explains the artifacts that make up an entity object, how to work with entities and resource bundles, and many advanced topics, including inheritance, change history tracking, custom properties, validation and cursor handling.  Chapter 4 - you guessed it - is all about View objects. Comparable to entities, you learn about the XM files and classes that make a view object, as well as how to define and work with queries. List-of-values, inheritance, polymorphism, bind variables and data filtering are interesting - and important topics that follow. Again the chapter provides helpful sequence diagrams for you to understand what happens internally within a view object. Chapter 5 focuses on advanced view object and entity object topics, like lifecycle callback methods and when you want to override them. This chapter is a good digest of Jobinesh's blog entries (which most ADF developers have in their bookmark list). Really worth reading ! Chapter 6 then is bout Application Modules. Beside of what application modules are, this chapter covers important topics like properties, passivation, activation, application module pooling, how and where to write custom logic. In addition you learn about the AM lifecycle and request sequence. Chapter 7 is about the ADF binding layer. If you are new to Oracle ADF and got lost in the more advanced ADF Business Components chapters, then this chapter is where you get back into the game. In very easy terms, Jobinesh explains what the ADF binding is, how it fits into the JSF request lifecycle and what are the metadata file involved. Chapter 8 then goes into building data bound web user interfaces. In this chapter you get the basics of JavaServer Faces (e.g. managed beans) and learn about the interaction between the JSF UI and the ADF binding layer. Later this chapter provides advanced solutions for working with tree components and list of values. Chapter 9 introduces bounded task flows and ADF controller. This is a chapter you want to read if you are new to ADF of have started. Experts don't find anything new here, which doesn't mean that it is not worth reading it (I for example, enjoyed the controller talk very much) Chapter 10 is an advanced coverage of bounded task flow and talks about contextual events  Chapter 11 is another highlight and explains error handling, trains, transactions and more. I can only recommend you read this chapter. I am aware of many documents that cover exception handling in Oracle ADF (and my Oracle Magazine article for January/February 2013 does the same), but none that covers it in such a great depth. Chapter 12 covers ADF best practices, which is a great round-up of all the tips provided in this book (without Jobinesh to repeat himself). Its all cool stuff that helps you with your ADF projects. In summary, "Oracle ADF Real World Developer’s Guide" by Jobinesh Purushothaman is a great book and addition for all Oracle ADF developers and those who want to become one. Frank

    Read the article

  • Announcing the June 2012 Release of the Ajax Control Toolkit

    - by Stephen.Walther
    I’m excited to announce the June 2012 release of the Ajax Control Toolkit. You can download the new release by visiting http://AjaxControlToolkit.CodePlex.com or (better) download the new release with NuGet: Install-Package AjaxControlToolkit The Ajax Control Toolkit continues to be super popular. The previous release (May 2012) had over 87,000 downloads from CodePlex.com and over 16,000 downloads from NuGet. That’s over 100,000 downloads in less than 2 months. Security Improvements for the HtmlEditorExtender Unfortunately, in the previous release, we made the HtmlEditorExtender too secure! We upgraded the version of the Microsoft Anti-Cross Site Scripting Library included in the Ajax Control Toolkit to the latest version (version 4.2.1) and the latest version turned out to be way too aggressive about stripping HTML. It not only strips dangerous tags such as <script> tags, it also strips innocent tags such as <b> tags. When the latest version of the Microsoft Anti-Cross Site Scripting Library is used with the HtmlEditorExtender, the library strips all rich content from the HtmlEditorExtender control which defeats the purpose of using the control. Therefore, we had to find a replacement for the Microsoft Anti-Cross Site Scripting Library. In this release, we’ve created a new HTML sanitizer built on the HTML Agility Pack. If you were using the AntiXssSanitizerProvider then you will need to substitute the HtmlAgilityPackSanitizerProvider. In particular, you need to modify the sanitizer sections in your Web.config file like this: <configuration> <configSections> <sectionGroup name="system.web"> <section name="sanitizer" requirePermission="false" type="AjaxControlToolkit.Sanitizer.ProviderSanitizerSection, AjaxControlToolkit" /> </sectionGroup> </configSections> <system.web> <sanitizer defaultProvider="HtmlAgilityPackSanitizerProvider"> <providers> <add name="HtmlAgilityPackSanitizerProvider" type="AjaxControlToolkit.Sanitizer.HtmlAgilityPackSanitizerProvider"></add> </providers> </sanitizer> </system.web> </configuration> We made one other backwards-breaking change to improve the security of the HtmlEditorExtender. We want to make sure that users don’t accidently use the HtmlEditorExtender without an HTML sanitizer by accident. Therefore, if you don’t configure a HTML sanitizer provider in the web.config file then you’ll get the following error: If you really want to use the HtmlEditorExtender without using an HTML sanitizer – for example, you are using the HtmlEditorExtender for an Intranet application and you trust all of your fellow employees – then you can explicitly indicate that you don’t want to enable HTML sanitization by setting the EnableSanitization property to false like this: <ajaxToolkit:HtmlEditorExtender TargetControlID="txtComments" EnableSanitization="false" runat="server" /> Please don’t ever set the EnableSanitization property to false for a public website. If you disable HTML sanitization then you are making your website an easy target for Cross-Site Scripting attacks. Lots of Fixes for the ComboBox Control In the latest release, we also made several important bug fixes and feature enhancements to the ComboBox control. Here’s the list of issues that we fixed: 22930 — ComboBox doesn’t close its drop down list when losing input focus to another ComboBox control 23140 — ComboBox Issues – Delete, Backspace, Period 23142 — ComboxBox SelectedIndex = -1 does not clear text 24440 — ComboBox postback on enter 25295 — ComboBox problems when container is hidden at page load 25469 — ComboBox – MaxLength ignored 26686 — Backspace and Delete exception when optionList is null 27148 — Combobox breaks if ClientIDMode is static Fixes to Other Controls In this release, we also made bug fixes and enhancements to the UpdatePanelAnimation, Tabs, and Seadragon controls: 21310 — OnUpdated animation starts before OnUpdating has finished 26690 — Seadragon Control’s openTileSource() method doesn’t work (with fix) Title is required We also fixed an issue with the Tabs control which would result in an InvalidOperation exception. Summary I want to thank the Superexpert team for the hard work that they put into this release. In particular, I want to thank them for their effort in researching, building, and writing unit tests for the HtmlAgilityPack HTML sanitizer.

    Read the article

  • Hack Extension Files to Make Them Version-Compatible for Firefox

    - by Asian Angel
    A well known drawback in using Firefox is the problem with extension compatibility when a new major version is released. Whether it is for a new extension that you are trying for the first time or an old favorite we have a way to get those extensions working for you again. There are multiple reasons why you might want to choose this method to fix a non-compatible extension: You are uncomfortable with tweaking the “about:config” settings You prefer to maintain the original “about:config” settings in a pristine state and like having compatibility checking active You are looking to gain some “geek cred” Keep in mind that most extensions will work perfectly well with a new version of Firefox and simply have the “version compatibility number” problem. But once in a while there may be one that needs to have some work done on it by the extension’s author. The Problem Here is a perfect example of everyone’s least favorite “extension message”. This is the last thing that you need when all that you want is for your favorite extension (or a new one) to work on a fresh clean install. Note: This works nicely to “replace” non-compatible extensions already present in your browser if you are simply upgrading. Hacking the XPI File For this procedure you will need to manually download the extension to your hard-drive (right click on the extension’s “Install Button” and select “Save As”). Once you have done that you are ready to start hacking the extension. For our example we chose the “GCal Popup Extension”. The best thing to do is place the extension in a new folder (i.e. the Desktop or other convenient location) then unzip it just the same way that you would with any regular zip file. Once it is unzipped you will see the various folders and files that were in the “xpi file” (we had four files here but depending on the extension the number may vary). There is only one file that you need to focus on…the “install.rdf” file. Note: At this point you should move the original extension file to a different location (i.e. outside of the folder) so that it is no longer present. Open the file in “Notepad” so that you can change the number for the “maxVersion”. Here the number is listed as “3.5.*” but we needed to make it higher… Replacing the “5” with a “7” is all that we needed to do. Once you have entered your new “maxVersion” number save the file. At this point you will need to re-zip all of the files back into a single file. Make certain that you “create” a file with the “.zip file extension” otherwise this will not work. Once you have the new zip file created you will need to rename the entire file including the “file extension”. For our example we copied and pasted the original extension name. Once you have changed the name click outside of the “text area”. You will see a small message window like this asking for confirmation…click “Yes” to finish the process. Now your modified/updated extension is ready to install. Drag the extension into your browser to install it and watch that wonderful “Restart to complete the installation.” message appear. As soon as your browser starts you can check the “Add-ons Manager Window” and see the version compatibility numbers for the extension. Looking very very nice! And just like that your extension should be up and running without any problems. Conclusion If you are looking to try something new, gain some geek cred, or just want to keep your Firefox install as close to the original condition as possible this method should get those extensions working nicely for you again. Similar Articles Productive Geek Tips Make Firefox Extensions Compatible After Firefox Update Breaks Them For No Good ReasonCheck Extension Compatibility for Upcoming Firefox ReleasesFirefox 3.6 Release Candidate Available, Here’s How to Fix Your Incompatible ExtensionsHow To Force Extension Compatibility with Firefox 3.6+Test and Report Add-on Compatibility in Firefox TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional 15 Great Illustrations by Chow Hon Lam Easily Sync Files & Folders with Friends & Family Amazon Free Kindle for PC Download Stretch popurls.com with a Stylish Script (Firefox) OldTvShows.org – Find episodes of Hitchcock, Soaps, Game Shows and more Download Microsoft Office Help tab

    Read the article

  • Searching for tasks with code – Executables and Event Handlers

    Searching packages or just enumerating through all tasks is not quite as straightforward as it may first appear, mainly because of the way you can nest tasks within other containers. You can see this illustrated in the sample package below where I have used several sequence containers and loops. To complicate this further all containers types, including packages and tasks, can have event handlers which can then support the full range of nested containers again. Towards the lower right, the task called SQL In FEL also has an event handler not shown, within which is another Execute SQL Task, so that makes a total of 6 Execute SQL Tasks 6 tasks spread across the package. In my previous post about such as adding a property expressionI kept it simple and just looked at tasks at the package level, but what if you wanted to find any or all tasks in a package? For this post I've written a console program that will search a package looking at all tasks no matter how deeply nested, and check to see if the name starts with "SQL". When it finds a matching task it writes out the hierarchy by name for that task, starting with the package and working down to the task itself. The output for our sample package is shown below, note it has found all 6 tasks, including the one on the OnPreExecute event of the SQL In FEL task TaskSearch v1.0.0.0 (1.0.0.0) Copyright (C) 2009 Konesans Ltd Processing File - C:\Projects\Alpha\Packages\MyPackage.dtsx MyPackage\FOR Counter Loop\SQL In Counter Loop MyPackage\SEQ For Each Loop Wrapper\FEL Simple Loop\SQL In FEL MyPackage\SEQ For Each Loop Wrapper\FEL Simple Loop\SQL In FEL\OnPreExecute\SQL On Pre Execute for FEL SQL Task MyPackage\SEQ Top Level\SEQ Nested Lvl 1\SEQ Nested Lvl 2\SQL In Nested Lvl 2 MyPackage\SEQ Top Level\SEQ Nested Lvl 1\SQL In Nested Lvl 1 #1 MyPackage\SEQ Top Level\SEQ Nested Lvl 1\SQL In Nested Lvl 1 #2 6 matching tasks found in package. The full project and code is available for download below, but first we can walk through the project to highlight the most important sections of code. This code has been abbreviated for this description, but is complete in the download. First of all we load the package, and then start by looking at the Executables for the package. // Load the package file Application application = new Application(); using (Package package = application.LoadPackage(filename, null)) { int matchCount = 0; // Look in the package's executables ProcessExecutables(package.Executables, ref matchCount); ... // // ... // Write out final count Console.WriteLine("{0} matching tasks found in package.", matchCount); } The ProcessExecutables method is a key method, as an executable could be described as the the highest level of a working functionality or container. There are several of types of executables, such as tasks, or sequence containers and loops. To know what to do next we need to work out what type of executable we are dealing with as the abbreviated version of method shows below. private static void ProcessExecutables(Executables executables, ref int matchCount) { foreach (Executable executable in executables) { TaskHost taskHost = executable as TaskHost; if (taskHost != null) { ProcessTaskHost(taskHost, ref matchCount); ProcessEventHandlers(taskHost.EventHandlers, ref matchCount); continue; } ... // // ... ForEachLoop forEachLoop = executable as ForEachLoop; if (forEachLoop != null) { ProcessExecutables(forEachLoop.Executables, ref matchCount); ProcessEventHandlers(forEachLoop.EventHandlers, ref matchCount); continue; } } } As you can see if the executable we find is a task we then call out to our ProcessTaskHost method. As with all of our executables a task can have event handlers which themselves contain more executables such as task and loops, so we also make a call out our ProcessEventHandlers method. The other types of executables such as loops can also have event handlers as well as executables. As shown with the example for the ForEachLoop we call the same ProcessExecutables and ProcessEventHandlers methods again to drill down into the hierarchy of objects that the package may contain. This code needs to explicitly check for each type of executable (TaskHost, Sequence, ForLoop and ForEachLoop) because whilst they all have an Executables property this is not from a common base class or interface. This example was just a simple find a task by its name, so ProcessTaskHost really just does that. We also get the hierarchy of objects so we can write out for information, obviously you can adapt this method to do something more interesting such as adding a property expression. private static void ProcessTaskHost(TaskHost taskHost, ref int matchCount) { if (taskHost == null) { return; } // Check if the task matches our match name if (taskHost.Name.StartsWith(TaskNameFilter, StringComparison.OrdinalIgnoreCase)) { // Build up the full object hierarchy of the task // so we can write it out for information StringBuilder path = new StringBuilder(); DtsContainer container = taskHost; while (container != null) { path.Insert(0, container.Name); container = container.Parent; if (container != null) { path.Insert(0, "\\"); } } // Write the task path // e.g. Package\Container\Event\Task Console.WriteLine(path); Console.WriteLine(); // Increment match counter for info matchCount++; } } Just for completeness, the other processing method we covered above is for event handlers, but really that just calls back to the executables. This same method is called in our main package method, but it was omitted for brevity here. private static void ProcessEventHandlers(DtsEventHandlers eventHandlers, ref int matchCount) { foreach (DtsEventHandler eventHandler in eventHandlers) { ProcessExecutables(eventHandler.Executables, ref matchCount); } } As hopefully the code demonstrates, executables (Microsoft.SqlServer.Dts.Runtime.Executable) are the workers, but within them you can nest more executables (except for task tasks).Executables themselves can have event handlers which can in turn hold more executables. I have tried to illustrate this highlight the relationships in the following diagram. Download Sample code project TaskSearch.zip (11KB)

    Read the article

  • SnagIt Live Writer Plug-in Updated

    - by Rick Strahl
    Ah, I love SnagIt from TechSmith and I use the heck out of it almost every day. So no surprise that I've decided some time ago to integrate SnagIt into a few applications that require screen shots extensively. It's been a while since I've posted an update to my small SnagIt Windows Live Writer plug-in. There have been a few nagging issues that have crept up with recent changes in the way SnagIt handles captures in recent versions and they have been addressed in this update of SnagIt. Personally I love SnagIt and use it extensively mostly for blogging, but also for writing documentation and articles etc. While there are many other (and also free) tools out there to do basic screen captures, SnagIt continues to be the most convenient tool for me with its nice built in capture and effects editor that makes creating professional looking captures childishly simple. And maybe even more importantly: SnagIt has a COM interface that can be automated and  makes it super easy to embed into other applications. I've built plugins for SnagIt as well as for one of my company's own tools, Html Help Builder. If you use the Windows Live Writer offline WebLog Editor to write blog posts and have a copy of SnagIt it's probably worth your while to check this out if you haven't already. In case you haven't, this plugin integrates SnagIt with Live Writer so you can easily capture and edit content and embed it into a post. Captures are shown in the SnagIt Preview editor where you can edit the image and apply image markup or effects, before selecting Finish (or Cancel). The final image can then be pasted directly into your Live Writer post. When installed the SnagIt plug-in shows up on the PlugIn list or in the Plug-Ins toolbar shortcut: Once you select the Plug in you get the capture window that allows you to customize the capture process which includes most of the useful SnagIt capture options: Once you're done capturing the image shows up in the SnagIt Image Editor and you can crop, mark up and apply effects. When done you click the Finish button and the image is embedded right into your blog post. Easy - how do you think the images in this blog entry got in here? The beauty of SnagIt is that it's all easily integrated - Capturing, editing and embedding, it only takes a few seconds to do it all especially if you save image effect presets in SnagIt. What's updated The main issue addressed in this update has to do with the plug-in updates the Live Writer window. When a capture starts Live Writer gets minimized to get out of the way to let you pick your capture source. When the capture is complete and the image has been embedded Live Writer is activated once again. Recent versions of SnagIt however had changed the Window positioning of SnagIt so that Live Writer ended up popping up back behind the SnagIt window which was pretty annoying. This update pushes Live Writer back to the top of the window stack using some delaying tactics in the code. There have also been a few small changes to the way the code interacts with the COM object which is more reliable if a capture fails or SnagIt blows up or is locked because it's already in a capture outside of the automation interface. Source Code SnagIt Automation is something I actually use a lot. As mentioned I've integrated this automation into Live Writer as well as my documentation tool Html Help Builder, which I use just about daily. The SnagIt integration has a similar interface in that application and provides similar functionality. It's quite useful to integrate SnagIt into other applications. Because it's quite useful to embed SnagIt into other apps there's source code that you can download and embed into your own applications. The code includes both the dialog class that is automated from Live Writer, as well as the basic capture component that captures images to a disk file. Resources Download the SnagIt Capture Plug-in Installer An MSI installer that you can run that will install the plug-in into Live Writer's PlugIns directory. Source Code to the SnagIt Capture Plug-in Contains the plug-in assembly, as well as the source code to the plug-in and the setup project.© Rick Strahl, West Wind Technologies, 2005-2011Posted in Live Writer  WebLog   Tweet (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

    Read the article

  • Formal Languages, Inductive Proofs &amp; Regular Expressions

    - by MarkPearl
    So I am slogging away at my UNISA stuff. I have just finished doing the initial once non stop read through the first 11 chapters of my COS 201 Textbook - “Introduction to Computer Theory 2nd Edition” by Daniel Cohen. It has been an interesting couple of days, with familiar concepts coming up as well as some new territory. In this posting I am going to cover the first couple of chapters of the book. Let start with Formal Languages… What exactly is a formal language? Pretty much a no duh question for me but still a good one to ask – a formal language is a language that is defined in a precise mathematical way. Does that mean that the English language is a formal language? I would say no – and my main motivation for this is that one can have an English sentence that is correct grammatically that is also ambiguous. For example the ambiguous sentence: "I once shot an elephant in my pyjamas.” For this and possibly many other reasons that I am unaware of, English is termed a “Natural Language”. So why the importance of formal languages in computer science? Again a no duh question in my mind… If we want computers to be effective and useful tools then we need them to be able to evaluate a series of commands in some form of language that when interpreted by the device no confusion will exist as to what we were requesting. Imagine the mayhem that would exist if a computer misinterpreted a command to print a document and instead decided to delete it. So what is a Formal Language made up of… For my study purposes a language is made up of a finite alphabet. For a formal language to exist there needs to be a specification on the language that will describe whether a string of characters has membership in the language or not. There are two basic ways to do this: By a “machine” that will recognize strings of the language (e.g. Finite Automata). By a rule that describes how strings of a language can be formed (e.g. Regular Expressions). When we use the phrase “string of characters”, we can also be referring to a “word”. What is an Inductive Proof? So I am not to far into my textbook and of course it starts referring to proofs and different types. I have had to go through several different approaches of proofs in the past, but I can never remember their formal names , so when I saw “inductive proof” I thought to myself – what the heck is that? Google to the rescue… An inductive proof is like a normal proof but it employs a neat trick which allows you to prove a statement about an arbitrary number n by first proving it is true when n is 1 and then assuming it is true for n=k and showing it is true for n=k+1. The idea is that if you want to show that someone can climb to the nth floor of a fire escape, you need only show that you can climb the ladder up to the fire escape (n=1) and then show that you know how to climb the stairs from any level of the fire escape (n=k) to the next level (n=k+1). Does this sound like a form of recursion? No surprise then that in the same chapter they deal with recursive definitions. An example of a recursive definition for the language EVEN would the 3 rules below: 2 is in EVEN If x is in EVEN then so is x+2 The only elements in the set EVEN are those that be produced by the rules above. Nothing to exciting… So if a definition for a language is done recursively, then it makes sense that the language can be proved using induction. Regular Expressions So I am wondering to myself what use is this all – in fact – I find this the biggest challenge to any university material is that it is quite hard to find the immediate practical applications of some theory in real life stuff. How great was my joy when I suddenly saw the word regular expression being introduced. I had been introduced to regular expressions on Stack Overflow where I was trying to recognize if some text measurement put in by a user was in a valid form or not. For instance, the imperial system of measurement where you have feet and inches can be represented in so many different ways. I had eventually turned to regular expressions as an easy way to check if my parser could correctly parse the text or not and convert it to a normalize measurement. So some rules about languages and regular expressions… Any finite language can be represented by at least one if not more regular expressions A regular expressions is almost a rule syntax for expressing how regular languages can be formed regular expressions are cool For a regular expression to be valid for a language it must be able to generate all the words in the language and no other words. This is important. It doesn’t help me if my regular expression parses 100% of my measurement texts but also lets one or two invalid texts to pass as well. Okay, so this posting jumps around a bit – but introduces some very basic fundamentals for the subject which will be built on in later postings… Time to go and do some practical examples now…

    Read the article

< Previous Page | 192 193 194 195 196 197 198 199 200 201 202 203  | Next Page >