Search Results

Search found 16809 results on 673 pages for 'nothing 2 lose'.

Page 198/673 | < Previous Page | 194 195 196 197 198 199 200 201 202 203 204 205  | Next Page >

  • PXE-E32 TFTP Open Timeout While Attempting to PXE Boot from Windows Deployment Services

    - by bschafer
    I'm running Windows Deployment Services on Windows Server 2008 R2 on top of an ESX 4.0 box. This is the only function of this VM instance, although it had previously functioned as an AD Domain Controller. My DHCP server is running on our primary Domain Controller, which is also Server 2008 R2, but running on metal. Everything was working perfectly until we recently had our backup generator fail during a power outage, causing all of our servers and networking equipment to lose power for a period of time. When we brought all of our equipment back up, everything was working as expected except for WDS. Our network is split up into several different vlans. Now, depending on which vlan the client computer is on, it's behaving differently when attempting to PXE boot into WDS. Our servers are located on the 10.55.x.x vlan, which, due to the nature of it, has no DHCP server active in it. The first computer we plugged in happened to be in the 10.99.x.x vlan, which is supposed to be reserved for network management devices (i.e. switches), but we've been using it occasionally otherwise. That computer gave us PXE-E11 ARP Timeout errors. When we moved to a different computer on the 10.19.x.x vlan (for general purpose use), it finally gets an IP from DHCP, but it presents us with a very stumping PXE-E32 TFTP Open Timeout error. Before the power outage, it didn't matter which vlan a device was on; it would PXE boot and image just fine. I've made no changes to anything server-side. Everything is configured exactly the same way it was on my WDS and DHCP servers as before the power outage. I've tried several different computers, including different models. All of this, combined with the quirky behavior depending on the vlan, makes me think something went wrong in one or more of our switches, probably because of the power outage. Unfortunately, I'm no network guy, and I know very little about how to configure our switches properly. Is this an issue with switches, etc? If so, how can I fix it? Is there some magical option I'm not aware of? Does anybody out there have any hunches? I've pretty much exhausted my ideas. Our main switch is an HP Procurve 5406. We also have 3x HP Procurve 4208 switches. The ESX Server is an HP ProLiant DL380 G6. The WDS VM is currently using the VMXNET3 network adaptor, but we've also tried the E1000 adaptor.

    Read the article

  • Simple Backup Strategy for Amazon EC2 instances / volumes?

    - by minerj
    You have entered Introductory Backups for Amazon EC2 EBS-backed Windows Images 010... I have been browsing my brains out to find a simple backup strategy for our single windows 2008 server running SharePoint Services. This is an EBS-backed image of one server with one data volume. I don’t need anything exotic. I only need a “daily” backup (losing a day’s worth of data is not catastrophic). We have created and saved an EBS backed AMI image (Windows 2008) we are comfortable using. We started off making backups by simply creating a new EBS AMI image. This is really simple, but the running server is put offline during the first 10 – 15 minutes of creating the image – not ideal. The standard way of creating backups would seem to be creating snapshots of volumes attached to a running instance. Again it’s pretty simple and the server remains usable during the snapshot generation. The apparent Catch-22 is that you can’t simply launch a new instance directly from a snapshot. I know how to bundle a running instance to S3 storage and then register the AMI from the S3 bucket. This does allow me to capture a backup of a running instance and, if the running instance is lost, register the AMI from the S3 bucket and launch the new AMI to recover the instance, but this seems really convoluted and it seems ridiculous to have to juggle back and forth between the AWS Console and the S3 Organizer plug-in for Firefox to get this accomplished. (Please don't mention the command line approach, this is an 010 level course). From playing around with EBS-backed images, the following approach appears to work for me (all done within the AWS Console): 1.For your backups, simply snapshot the system volume (/dev/sda1) as needed. 2.If you lose your running instance, do the following: a.Create a new volume from your last snapshot backup b.Launch another instance of your starting AMI (must be EBS-backed) c.Stop this instance. d.Detach the existing system volume from the new stopped instance and discard. e.Attach the newly created volume as system volume (/dev/sda1) to the stopped instance. f.Re-start the new instance. I have tested this out a couple of times and it seems to work for me. Question: Is there anything wrong with this approach?

    Read the article

  • Real server, Multiple IP Addresses, HyperV Virtual Server, How to partition IPs across real and Virtual NICs

    - by Steven_W
    This is a slightly difficult problem to explain without same basic background information - I'll try and refine the question later as necessary Originally, I have a single hosted server (Win 2008R2) with the following range of 8 IP addresses. - Single NIC - IP: x.x.128.72 -> x.x.128.79 - Subnet: x.x.255.192 - GW: x.x.128.65 After installing Hyper-V and setting up a single virtual server on the same box, I then wanted to assign one of the IP addresses to the virtual server, leaving everything else running normally. -- Firstly, I tried using the "External" network, but (even after setting IPs on the "Virtual Adapter" similar to Here but struggled to get networking running at all. I needed to keep the server running (otherwise I would have spent more time pursuing this approach) Q1 ... Was this a sensible thing to do ? Should I have carried on down this route ? -- I then decided to try different approach - Set the HyperV network to "Internal" (visible to Management OS) - Physical NIC - IP: x.x.128.72 -> x.x.128.75 - Subnet: x.x.255.192 - GW: x.x.128.65 - Virtual NIC - IP: x.x.128.78 - Subnet: x.x.255.252 - GW: x.x.128.72 ... { The same as the IP of the physical NIC ) - Virtual OS-NIC - IP: x.x.128.77 - Subnet: x.x.255.252 - GW: x.x.128.78 ... { The same as the IP of the host virtual-NIC ) -- Surprisingly enough, this approach actually worked, and I was able to connect from all the following: - Internet to/from physical NIC (x.x.128.72) - physical NIC (x.x.128.72) to virtual-OS-NIC (x.x.128.77) e.g. testing via ping + FTP - Internet to/from virtual-OS-NIC (x.x.128.72) -- The problem I have is that this approach seems to only last for a short while (a few hours). After this time, it seems that I lose the ability to connect from Virtual-OS-NIC to/from the internet (but I can still connect from the host-OS to the virtual-OS and from the host-OS to the internet) I have re-tested this a couple of times with the same results ... I leave the server on for a few hours (e.g. overnight), and when I come back in the morning, the Virtual-OS loses the ability to route to the internet -- I'm not quite sure what to look at next (or whether I'm going about this completely the wrong way ) One "possible relevant item" is that the host-OS is also running RRAS (Routing and Remote Access), but this is only to run a simple VPN -- Q2 - Wheat should I be looking at next ? (Any good references / recommendations of what to try) Would appreciate any thoughts or comments (even if you tell me I'm going about this the wrong way)

    Read the article

  • Multi-Role Domain Controllers for Small Offices (< 50 clients)

    - by kce
    Warning: I'm a Linux/*NIX admin so this is all new to me. I understand that it's not considered a good idea to have only a single domain controller, and that it is also probably a good idea for a domain controller to only do AD/DHCP/DNS (Here). We have two offices, location A with 30 users and location B with 10 users. Our two offices are separated by a WAN that is not particularly robust so I have be instructed that we need to have standalone services in each office. This means that according to "best practices" we will need to build a domain controller and a separate file server in each office. Again, I am not knowledgeable in the ways of Windows but this seems a little unnecessary for an organization of 40 users. People have commented that I could "get away with" running file services on the domain controller as long as the "load is light". That just seems to generate more questions than it answers. What constitutes light load? What are the potential consequences of mixing these roles? Ideally I would prefer to only have one physical machine at each location. The one in location A (the location with IT staff) can act as the primary domain controller and the one in the smaller office can act as the backup domain controller. If either domain controller fails we can still use the other one for authentication (albeit with some latency) and if the WAN connection fails each office still has access to their respective "local" domain controller. If the file services are ALSO run on each server (and synchronized with something like DFS), a similar arrangement in terms of redundancy can be had without having to purchase, build and install two additional separate servers. It's not that I'm adverse to that (well, any more adverse than I am to whole thing to begin with) but to my simple mind it just seems, well a bit overkill. I can definitely see the benefits of functional separation when we're talking larger organizations, but I need to consider the additional overhead too. None of this excludes having a DRP setup for the domain controller/s. I assume you can lose two domain controllers just as easily as one.

    Read the article

  • In search of a network file system with extended caching to speed up file access

    - by Brecht Machiels
    I'm running a small home server that stores my documents. The disks in this server are in a RAID 1 configuration (using Linux md) and it's also periodically being backup up to an external hard drive to make sure I don't lose them. However, I'm always accessing the files from other computers on the home network using an SMB share, and this results in a considerable speed penalty (especially when connected over WLAN). This is quite annoying when editing large files, such as digital camera RAWs, for example. I've been looking for a solution to this problem. It would have to offer some kind of local caching to speed up the file access. The client would preferably not keep a copy of all data on the server, as it consists of a very large collection of photographs, most of which I will not access frequently. Instead, it should only cache the accessed files and sync the changes back in the background. Ideally, it would also do some smart read-ahead (cache the files that are in the same directory as the currently opened file, for examples), but I suppose that's asking a bit much. Synchronization should be automatic (on file change). Conflicting file changes (at the same time on different clients) are unlikely to happen in my use case, but I would prefer if they are handled properly (notification to the user). I've come across the following options, so far: something similar to Dropbox. iFolder seems to be the only thing that comes close, but its reputation (stability) and requirements put me off. A distributed file system such as OpenAFS. I'm not sure this will speed up file access. It is probably overkill for what I need. Maybe NFS or even Samba offer these possibilities. I read a bit about Windows' Offline Files, but its operation seems limited (at least on Windows XP). As this is just for personal use, I'm not willing to spend a lot of money. A free solution would be preferred. Also, the server needs to run on Linux, and I need a client for at least Windows.

    Read the article

  • route lan traffic through wirless mifi

    - by Randall Blake
    I have a Windows 7 laptop accessing the internet through Verizon wireless MIFI configured as 192.168.1.1. It supports only 5 wireless connections, so I don't want to use up connections unnecessarily. That laptop has an ethernet nic which I have given a static IP of 192.168.0.5. Everything else on the 192.168.0.0 network acquires an address via DHCP from a DLink router whose address is 192.168.0.1. Also on that network are a printer, some network cameras, and a linux pc. The linux pc does not have a wireless card (and I don't want to buy one). The linux pc is located at 192.168.0.122. I can ping the linux pc from the windows pc. But I cannot access the internet from the linux pc. I can ping everything on the 192.168.0.0 network EXCEPT the ethernet card in the Windows PC. It seems as though my DLink router will not route requests to the 192.168.0.5 nic on the windows pc. My windows pc has a default route pointing to the 192.168.1.0 network. It also has a route telling it to route all traffic destined for the 192.168.0.0 network through the 192.168.0.5 interface. I have tried adding a default route to the linux pc to "gateway" 192.168.0.5, but that does not work. I have also tried adding a default route to the linux pc to the gateway 192.168.0.1 (the DLink router) but that will not give me internet access either (over the 192.168.1.0 network). I tried these two different routes at different times - I did not set them both at the same time. I suppose this is a simple problem to solve, but I cannot seem to solve it. How can I give internet access over the 192.168.1.1 MIFI to my linux pc on 192.168.0.122? Thanks EDIT: Additional Info Internet | | MIFI (192.168.1.1) (wireless) | | (192.168.1.3) (wireless) Windows 7 PC Dlink Router (192.168.0.1) ------------ (192.168.0.5) (wired) | | |linux pc (192.168.0.122) (wired) | |printer (192.168.0.100) (wireless) | |network cameras, etc (192.168.0.103) (wireless) Only the windows pc is multi-homed with a wireless nic that connects to the MIFI wirelessly, and an ethernet nic with a wired connection to the DLink router. (The DLink permits both wired and wireless connections.) I don't want to use Windows internet connection sharing because I believe it will set up the ethernet nic as a gateway on 192.168.0.1 and a DHCP server. I already have the Dlink performing that role and I don't want to change that if I do not have to. (The Dlink permits me to make DHCP reservations and I really like that feature. I don't want to lose it.)

    Read the article

  • Profiles and using the local profile for a domain user

    - by Harry
    I’m having some trouble with profiles and would like to reach out for some help. I’ve tried to do some research to help myself along, but I’m not making much progress on my own. I’ve pretty much taken over the sys admin duties for my small lab, I don’t have much experience to justify it besides I’m the only with the time and dedication to go at it (The environment was in a state of disrepair). My network and domain I look over are extremely small by most standards, about 10 users at a time. They are pretty intensive activity on the network, and we do work with fairly large files. None of the network is online, which is nice at the moment because it allows me not to have another headache. On to my profile problem, I have set up roaming profiles for the users in the network. Now after a little research, I think I will be switching this to a hybrid of folder redirection and roaming profiles as this seems to best practice. I also don’t want the users having to wait for a long time if they have a bloated profile. Now I’ve finally got a build working using MDT. We have Mac Pros, and it wasn’t fun getting everything to play nice. The way I did this was by setting up a reference computer and installing all the software and tools that each user would need and editing the settings preferences to how we would need them. I think used MDT to do a sys prep and capture to create the image of my reference computer. Using the reference image I can push out my images to the rest of the desktops in my environment. The issue I’m having is when we join the computer to domain. The user can login and operate fine on the computer, but I’d like a more. When the user is logged on with their domain user name they lose a lot of the icons I had on my reference image, as well as the desktop background and some other miscellaneous settings. I would love to have the user log on using their domain user name and see the icons and desktop environment as I had it setup on the reference computer. I’m not sure if it is possible, or something simple that I’m missing, but any help would be greatly appreciated!

    Read the article

  • DB2 Integrity Checks and Exception Tables

    - by imthefirestartr
    I am working on planning a migration of a DB2 8.1 database from a horrible IBM encoding to UTF-8 to support further languages etc. I am encountering an issue that I am stuck on. A few notes on this migration: We are using db2move to export and load the data and db2look to get the details fo the database (tablespaces, tables, keys etc). We found the loading process worked nicely with db2move import, however, the data takes 7 hours to load and this was unacceptable downtime when we actually complete the conversion on the main database. We are now using db2move load, which is much faster as it seems to simply throw the data in without integrity checks. Which leads to my current issue. After completing the db2move load process, several tables are in a check pending state and require integrity checks. Integrity checks are done via the following: set integrity for . immediate checked This works for most tables, however, some tables give an error: DB21034E The command was processed as an SQL statement because it was not a valid Command Line Processor command. During SQL processing it returned: SQL3603N Check data processing through the SET INTEGRITY statement has found integrity violation involving a constraint with name "blah.SQL120124110232400". SQLSTATE=23514 The internets tell me that the solution to this issue is to create an exception table based on the actual table and tell the SET INTEGRITY command to send any exceptions to that table (as below): db2 create table blah_EXCEPTION like blah db2 SET INTEGRITY FOR blah IMMEDIATE CHECKED FOR EXCEPTION IN blah USE blah_EXCEPTION NOW, here is the specific issue I am having! The above forces all the rows with issues to the specified exception table. Well that's just super, buuuuuut I can not lose data in this conversion, its simply unacceptable. The internets and IBM has a vague description of sending the violations to the exception tables and then "dealing with the data" that is in the exception table. Unfortunately, I am not clear what this means and I was hoping that some wise individual knows and could help me out and let me know how I can retrieve this data from these tables and place the data in the original/proper table rather than these exception tables. Let me know if you have any questions. Thanks!

    Read the article

  • Loose component cables causing HDMI video problems

    - by jwir3
    I'm not sure this is the correct forum, but I'll ask anyway. I have an A/V setup at home that has something like the following: Five Components (actually a few more, like a CD player, but they don't really relate to this question): Older Pioneer Receiver Digital Set Top Box Sony BluRay Player Samsung Plasma TV Speakers The reason for the receiver is so that all the sound can go through the speakers, rather than some going to the TV speakers and some to the external speakers. They are connected as follows: Digital Set Top Box connects via component video to Samsung TV directly via Component 2 (audio goes to Older Pioneer Receiver). Sony BluRay player is connected via HDMI 1 to TV, but audio goes to the receiver. Now, the problem I'm having is that when I have the digital set top box connected, there are times when the Netflix or Hulu streams I watch through the Sony BluRay player (it's connected to a router for internet access) will lose video. What I mean by this is that the sound of the episode will keep playing, but the screen will go black. If I jiggle the component cables, it will often come back. If I disconnect the component cables, it will always come back. I've noticed that one of the connections (the red component cable) doesn't like to sit very well in the component socket in the back of the digital set top box. It seems like there is a bad connection here, but it doesn't seem like this should be affecting the HDMI input at all. What I've noticed, though, is that when I disconnect the digital set top box completely (i.e. remove the component cable from the back of the TV), the problem seems to resolve itself. I'm not talking about actually removing the cable physically, because I thought perhaps the cables were mashing against one another, and possibly jiggling each other loose. To correct this possible problem, I took the component cable completely out of the cable ties it was in in the back of my entertainment center, as well as pulled the digital set top box out from the entertainment center altogether. It's now connected directly to the TV, without any other cables touching it to cause some kind of weird interference or just physical pulling on the cable. Same problem. If, however, I disconnect the component cable and just leave it sitting behind the TV, then the problem goes away. So, my question is this - what could be causing this? Is it a case where it's an improperly shielded component cable that's causing interference with the HDMI input, or something that's wrong with the TV? It's an intermittent problem, so it's difficult to track down. The TV isn't that old, so it's probably still under warranty. I'm just wondering if there is something else I can do that might reduce this problem without having to haul a massive television set out of my house to get repaired/replaced.

    Read the article

  • NTPD issue - syncs then slowly loses ground

    - by ethrbunny
    RHEL 5 workstation. Has been running smoothly for years. I did a 'pup' recently and followed with a nice, cleansing reboot. Afterwards the system had some startup issues: namely MySQL refused to start. It just went "...." for 5-10 minutes before I did another boot and skipped that step (using 'interactive'). This was the only service that didn't wan't to start normally. So now that the system is booted I've found that it doesn't want to stay in sync with the NTP master and after 48 hours is refusing any SSH other than root. NTPD: this service starts normally and gets a lock on 4 servers. Almost immediately it starts to lose ground and now (after 3 days) is almost 40 hours behind. If I stop/start the service it gets the lock, resets the system clock and starts losing ground again. The 'hwclock' is set properly and maintains its time. Login: when I (re)start the ntp server I am able to login normally. I assume this problem is due to losing sync with LDAP. This appears to be verified by LDAP errors in /var/log/messages. Suggestions on where to look? ADDENDA: Tried deleting the 'drift' file. After a bit it gets recreated with 0.000. from /var/log/messages: Jan 17 06:54:01 aeolus ntpdate[5084]: step time server 129.95.96.10 offset 30.139216 sec Jan 17 06:54:01 aeolus ntpd[5086]: ntpd 4.2[email protected] Tue Oct 25 12:54:17 UTC 2011 (1) Jan 17 06:54:01 aeolus ntpd[5087]: precision = 1.000 usec Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, 0.0.0.0#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, ::#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, ::1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, fe80::213:72ff:fe20:4080#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, 127.0.0.1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, 10.127.24.81#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: kernel time sync status 0040 Jan 17 06:54:02 aeolus ntpd[5087]: frequency initialized 0.000 PPM from /var/lib/ntp/drift Jan 17 06:54:02 aeolus ntpd[5087]: system event 'event_restart' (0x01) status 'sync_alarm, sync_unspec, 1 event, event_unspec' (0xc010) You can see the 30 second offset. This was after about one minute of operation.

    Read the article

  • Has the hardware in my modem gone bad?

    - by Tyler Scott
    I contacted CenturyLink about my modem recently and received useless and unrelated information. The problem seems to be that the modem will no longer save settings, the web interface is unusable except in internet explorer for some reason, and the modem keeps resetting. CenturyLink claimed it had to do with signal strength but I checked and it is currently between good and outstanding according to this. All of the lights remain green even when it starts acting up and I lose internet and shortly before it crashes and reboots. Does anyone have any idea what is going on or what I can do to fix it? (Asking CenturyLink again is obviously not going to help.) Update 1: Accessing the syslog from the web interface causes a crash. After it reboots, the log looks like as follows: 01/01/1970 12:01:29 AM Ethernet Ethernet client connected ,ip(192.168.0.2), mac(1c:6f:65:4c:6d:3b) 01/01/1970 12:01:38 AM Wireless 802.11 client connected ,ip(192.168.0.18), mac(d0:df:c7:c2:73:ca) 01/01/1970 12:01:41 AM System Event Line 0: VDSL2 link up, Bearer 0, us=20128, ds=40127 01/01/1970 12:01:43 AM dhcp6s[2028] dhcp6_ctl_authinit: failed to open /etc/dhcp6sctlkey: No such file or directory 01/01/1970 12:01:50 AM dhcp6s[2469] dhcp6_ctl_authinit: failed to open /etc/dhcp6sctlkey: No such file or directory 01/01/1970 12:01:52 AM radvd[2306] poll error: Interrupted system call 01/01/1970 12:01:56 AM PPP Link PPP server detected. 01/01/1970 12:01:56 AM PPP Link PPP session established. 01/01/1970 12:01:56 AM PPP Link PPP LCP UP. 01/01/1970 12:01:56 AM System Event Received valid IP address from server. Connection UP. 06/05/2014 08:16:01 AM radvd[2511] poll error: Interrupted system call 06/05/2014 08:16:03 AM System Event Dead loop on virtual device tun6rd, fix it urgently! 06/05/2014 08:16:03 AM System Event Dead loop on virtual device tun6rd, fix it urgently! 06/05/2014 08:16:03 AM System Event Dead loop on virtual device tun6rd, fix it urgently! 06/05/2014 08:16:03 AM System Event Dead loop on virtual device tun6rd, fix it urgently! 06/05/2014 08:16:03 AM System Event Dead loop on virtual device tun6rd, fix it urgently! 06/05/2014 08:16:03 AM System Event Dead loop on virtual device tun6rd, fix it urgently! 06/05/2014 08:16:03 AM System Event Dead loop on virtual device tun6rd, fix it urgently! 06/05/2014 08:16:03 AM System Event Dead loop on virtual device tun6rd, fix it urgently! 06/05/2014 08:16:03 AM System Event Dead loop on virtual device tun6rd, fix it urgently! 06/05/2014 08:16:04 AM System Event Dead loop on virtual device tun6rd, fix it urgently! 06/05/2014 08:16:04 AM dhcp6s[3236] dhcp6_ctl_authinit: failed to open /etc/dhcp6sctlkey: No such file or directory 06/05/2014 08:16:08 AM Wireless 802.11 client connected ,ip(192.168.0.7), mac(44:6d:57:c4:d7:08) I also get it to crash on various other pages. I am guessing the web server is unstable.

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • PC monitors shut off and system hangs while playing 3D games, but sound continues - Diagnosis?

    - by Jon Schneider
    Two days ago, I started running into a problem with my Windows PC: The PC's two connected monitors simultaneously lose signal and go black (as though the PC had been powered off). The keyboard's Numlock, Capslock, and Scroll Lights will become "stuck" in their current positions, as though the PC is hung. (For example, the Numlock light on the keyboard remains lit regardless of me pressing the Numlock key repeatedly.) No keyboard input does anything. (Ctrl+Alt+Del, Ctrl+Shift+Esc, Ctrl+C, etc.) However -- Whatever sound/music the PC was playing continues to play, and the PC's fans continue running, so the PC hasn't powered itself off or rebooted itself. Opening up the case, the graphics card is pretty hot to the touch. I had this happen 3 times in one evening. In all cases, I was playing a game with 3D graphics when the problem occurred (Torchlight, Minecraft, Magic: The Gathering 2012, Avadon: The Black Fortress demo). I have yet to have the problem happen when I'm not playing a game. This system has been running stable for about 2.5 years prior to this. I didn't make any changes to the system prior to the problem starting to occur. System specs: OS: Windows 7 64-bit Processor: Intel Core 2 Duo E7200 Wolfdale 2.53GHz Video Card: XFX GeForce 9800 GT 512 MB Motherboard: Foxconn P45A-S LGA 775 Intel ATX RAM: Corsair 4 GB (2x 2GB) DDR2-800 (PC2 6400) Full specs: New PC 2008 Troubleshooting tried so far (the problem occurred again after taking each of these steps, one at a time): Updated the video drivers with the latest drivers from NVidia's site. Opened up the case and cleaned out the video card and processor fans (both were pretty dirty). Installed and ran temperature monitor software. The processor idles at about 50 degrees C, and goes up to about 63 degrees C while playing a game (seems on the warm side, but not excessively so?). The software wasn't able to report the temperature of the GPU -- not sure this particular GPU supports software temperature readout? My initial diagnosis is that maybe the GPU is on its last legs (given that it seems to be running pretty hot, and the problem only occurs while playing 3D games). Does this seem likely? Or is it likely that this problem is caused by the processor, RAM, or motherboard? Or could this be a software issue of some kind? Thanks for any advice!

    Read the article

  • How to get more information from the system crash

    - by viraptor
    I'd like to debug an issue I'm having with a linux (debian stable) server, but I'm running out of ideas of how to confirm any diagnosis. Some background: The servers are running DL160 class with hardware raid between two disks. They're running a lot of services, mostly utilising network interface and CPU. There are 8 cpus and 7 "main" most cpu-hungry processes are bound to one core each via cpu affinity. Other random background scripts are not forced anywhere. The filesystem is writing ~1.5k blocks/s the whole time (goes up above 2k/s in peak times). Normal CPU usage for those servers is ~60% on 7 cores and some minimal usage on the last (whatever's running on shells usually). What actually happens is that the "main" services start using 100% CPU at some point, mainly stuck in kernel time. After a couple of seconds, LA goes over 400 and we lose any way to connect to the box (KVM is on it's way, but not there yet). Sometimes we see a kernel reporting hung task (but not always): [118951.272884] INFO: task zsh:15911 blocked for more than 120 seconds. [118951.272955] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [118951.273037] zsh D 0000000000000000 0 15911 1 [118951.273093] ffff8101898c3c48 0000000000000046 0000000000000000 ffffffffa0155e0a [118951.273183] ffff8101a753a080 ffff81021f1c5570 ffff8101a753a308 000000051f0fd740 [118951.273274] 0000000000000246 0000000000000000 00000000ffffffbd 0000000000000001 [118951.273335] Call Trace: [118951.273424] [<ffffffffa0155e0a>] :ext3:__ext3_journal_dirty_metadata+0x1e/0x46 [118951.273510] [<ffffffff804294f6>] schedule_timeout+0x1e/0xad [118951.273563] [<ffffffff8027577c>] __pagevec_free+0x21/0x2e [118951.273613] [<ffffffff80428b0b>] wait_for_common+0xcf/0x13a [118951.273692] [<ffffffff8022c168>] default_wake_function+0x0/0xe .... This would point at raid / disk failure, however sometimes the tasks are hung on kernel's gettsc which would indicate some general weird hardware behaviour. It's also running mysql (almost read-only, 99% cache hit), which seems to spawn a lot more threads during the system problems. During the day it does ~200kq/s (selects) and ~10q/s (writes). The host is never running out of memory or swapping, no oom reports are spotted. We've got many boxes with similar/same hardware and they all seem to behave that way, but I'm not sure which part fails, so it's probably not a good idea to just grab something more powerful and hope the problem goes away. Applications themselves don't really report anything wrong when they're running. I can run anything safely on the same hardware in an isolated environment. What can I do to narrow down the problem? Where else should I look for explanation?

    Read the article

  • load-causing processes disappearing from "top" ps -o pcpu shows bogus numbers

    - by Alec Matusis
    I administer a large number of servers, and I have this problem only with Ubuntu 10.04 LTS: I run a server under normal load (say load average 3.0 on an 8-core server). The "top" command shows processes taking certain % of CPU that cause this load average: say PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 11008 mysql 20 0 25.9g 22g 5496 S 67 76.0 643539:38 mysqld ps -o pcpu,pid -p11008 %CPU PID 53.1 11008 , everything is consistent. The all of the sudden, the process causing the load average disappears from "top", but the process continues to run normally (albeit with a slight performance decrease), and the system load average becomes somewhat higher. The output of ps -o pcpu becomes bogus: # ps -o pcpu,pid -p11008 %CPU PID 317910278 1587 This happened to at least 5 different severs (different brand new IBM System X hardware), each running different software: one httpd 2.2, one mysqld 5.1, and one Twisted Python TCP servers. Each time the kernel was between 2.6.32-32-server and 2.6.32-40-server. I updated some machines to 2.6.32-41-server, and it has not happened on those yet, but the bug is rare (once every 60 days or so). This is from an affected machine: top - 10:39:06 up 73 days, 17:57, 3 users, load average: 6.62, 5.60, 5.34 Tasks: 207 total, 2 running, 205 sleeping, 0 stopped, 0 zombie Cpu(s): 11.4%us, 18.0%sy, 0.0%ni, 66.3%id, 4.3%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 74341464k total, 71985004k used, 2356460k free, 236456k buffers Swap: 3906552k total, 328k used, 3906224k free, 24838212k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 805 root 20 0 0 0 0 S 3 0.0 1493:09 fct0-worker 982 root 20 0 0 0 0 S 1 0.0 111:35.05 fioa-data-groom 914 root 20 0 0 0 0 S 0 0.0 884:42.71 fct1-worker 1068 root 20 0 19364 1496 1060 R 0 0.0 0:00.02 top Nothing causing high load is showing on top, but I have two highly loaded mysqld instances on it, that suddenly show crazy %CPU: #ps -o pcpu,pid,cmd -p1587 %CPU PID CMD 317713124 1587 /nail/encap/mysql-5.1.60/libexec/mysqld and #ps -o pcpu,pid,cmd -p1624 %CPU PID CMD 2802 1624 /nail/encap/mysql-5.1.60/libexec/mysqld Here are the numbers from # cat /proc/1587/stat 1587 (mysqld) S 1212 1088 1088 0 -1 4202752 14307313 0 162 0 85773299069 4611685932654088833 0 0 20 0 52 0 3549 27255418880 5483524 18446744073709551615 4194304 11111617 140733749236976 140733749235984 8858659 0 552967 4102 26345 18446744073709551615 0 0 17 5 0 0 0 0 0 the 14th and 15th numbers according to man proc are supposed to be utime %lu Amount of time that this process has been scheduled in user mode, measured in clock ticks (divide by sysconf(_SC_CLK_TCK). This includes guest time, guest_time (time spent running a virtual CPU, see below), so that applications that are not aware of the guest time field do not lose that time from their calculations. stime %lu Amount of time that this process has been scheduled in kernel mode, measured in clock ticks (divide by sysconf(_SC_CLK_TCK). On a normal server, these numbers are advancing, every time I check the /proc/PID/stat. On a buggy server, these numbers are stuck at a ridiculously high value like 4611685932654088833, and it's not changing. Has anyone encountered this bug?

    Read the article

  • Local admin password recovery: Windows Vista

    - by Jim Dennis
    I am faced with an unsettling situation. A friend of my father's has rather suddenly become a widower. Naturally they've taken care of the bank accounts and all the normal mundane things that people have been doing for a century or so. However, she was the computer user of the household. He was aware that they had some online banking stuff and bill paying stuff ... and that she spent lots of time on FaceBook and stuff like that. However, he doesn't know what her local passwords were (actually only vaguely aware that her couple of desktop and couple of laptop system even had passwords). He's never heard of "admin" passwords so that's no good either. In the past I've used KNOPPIX and the old LinuxCare "bootable business card" to recover NT passwords. I've never done this with MS Windows Vista. So, I'm looking for the best advice on how to do this. Naturally I do have physical access to the systems (the two laptops are charging across the room from me; and her old desktop systems are, naturally, still back at his place). Getting it right is much more important than fast or easy (I don't want to mess up those filesystems and possibly lose some photos or other stuff that he or his kids or grandkids will want). (BTW: if anyone things this is some social engineering hack to play upon the sympathies of the community to get the information I'm asking for ... think about it for a minute. I know about IRC and the "warez" boards. I know I can find this stuff out there if I dig enough. I'm just asking here because it'll hopefully be faster and, secondarily to raise awareness. As more of us put more of our lives online ... as we get older and as places like FaceBook continue to widen the appeal of computing to a broader segment of older people ... we are, as computer nerds, going to see a lot more of this. Survivors will needs us to be careful, sensitive and ethically responsible as they try to recover those bits of legacy during their bereavement. I can now tell you, first hand, it sucks!)

    Read the article

  • Suggestions for splitting server roles amongst Hyper-V virtual servers / RAID6 or RAID10? / AppAssure

    - by Anon
    We have 2 Hyper-V hosts at present running 1 virtual server that was converted from a physical box running all roles. My plan is to split the roles over various virtual machines, upgrading to the latest software versions as I go, and use the backup server as a standby in case the main server fails. AppAssure backup software has a feature called Virtual Standby, so the VHD's can be ready to be fired up on the backup server if necessary. Off-site backups will be done via external USB drive for now. I'm just seeking some input/suggestions into how I'm planning to split the roles out amongst various virtual servers. Also, I'm curious how to setup the storage on the servers. We do not have any NAS's, SAN'S or any budget for this. What would the best RAID level be to use? I'm thinking either RAID6 (which is currently used) however I'm concerned about the write speeds, or RAID10 but again I'm worried that I can only lose 1 drive (from the same mirror) as opposed to any 2 with RAID6. I realise I have a hot swap for this, but what if a further drive fails during a rebuild? Is the write penalty of RAID6 worth the extra reliability over RAID10? Or will it be too slow with all the roles I am planning, therefore RAID10 is my only real option? The reason for the needed redundancy is I am the only technician and I'm not always on-site. Options I've considered: 1) 5 drives in RAID6 set, 200gb for host OS, rest for VM storage. 1 drive for hot swap - this is how it is currently setup 2) 4 drives in RAID10 set, 200gb for host OS, rest for VM storage. 2 drives for hot swap 3) 4 drives in RAID10 set for VM storage, 2 drives in RAID1 set for host OS. No drives for hot swap - While this is probably the best option with the amount of drives I have, I don't like the idea of having no hot swap 4) 3 drives in RAID6 set for VM storage, 2 drives in RAID1 set for host OS. 1 drive for hot swap All options give us enough storage capacity for our files, etc. We don't have any budget for extra drives or extra hot swap HD chassis for the servers. We have about 70 clients and about 150 users. MAIN SERVER Intel Xeon 5520 @ 2.27 GHz (2 processors) 16GB RAM 6 x 1TB Seagate Barracuda ES.2 Enterprise SATA drives Intel SRCSATAWB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: DC01 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM DC02 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM Member Server - DHCP server, File server, Print server - 1GB RAM SCCM Member Server - 4GB RAM Third Party Software Member Server - A/V server, Ticketing software, etc - 4GB RAM Exchange 2007 - 4GB RAM - however we are probably migrating to a hosted solution, therefore freeing up resources BACKUP SERVER Intel Xeon E5410 @ 2.33GHz (2 processors) 16GB RAM 6 x 2TB WD RE4 SATA drives Intel SRCSASRB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: AppAssure backup software - 8GB RAM

    Read the article

  • WiFi signal is lost every 3 minutes

    - by Software Monkey
    For several weeks now my Android phone has been losing it's WiFi signal momentarily, typically at about 3 minute intervals (about 3 minutes, 1.5 seconds) and occasionally at some longer interval that always seems to be just over 3 minutes. This causes an interruption of several seconds while the WiFi connection is re-established and typically fails any kind of download/streaming that is happening, makes web sites "unreachable" and generally makes the phone unusable as a data device due to the frequency. The signal remains down for about a second, but the phone takes a few more seconds to reconnect to the router. This happens regardless of proximity to the router, which otherwise show a very strong signal - usually -40 to -30 dBm or better in the same room, nowhere less than 060 dBm anywhere in the house. Changing channels does not help (I've tried 1, 4, 8 and 9). Nor does turning off the router's guest access. Nor does turning off the 5.0 GHz band. Monitoring the signal on my phone with WiFi analyzer, shows all WiFi signals on all channels drop to nothing when the WiFi connection is lost (there are two other networks on different channels which are strong enough to be relevant, with about 6 others constantly fading in and out). WiFi analyzer shows 3 separate signals for my router, the main 2.4 GHz, the guest 2.4 GHz and the 5.0 GHz. Using WiFi Analyzer on my wife's phone side-by-side shows no change in signal when my phone drops, nor does her phone drop. Monitoring the signal using our laptop, side-by-side likewise shows no signal loss and likewise the laptop does not lose it's WiFi connection. But, at work, the phone seems to not exhibit the same behavior, or, if it does, it's very occasional. Monitoring it all day at work I only saw the signal drop 3 or 4 times. The signal strength of the various networks there is comparatively weak. AT&T were super helpful: "Sorry, we can't help you with WiFi problems. You could try doing a factory reset on your phone". </sarcasm The router is relatively new, but has been working fine with this phone since last Dec. Phone : Motorola Atrix (about 8 months old). Router : Belkin N750 DB (F9K1103 v1 (01C)). Router Firmware: 1.00.46 (2011/10/28 6:37:11). Security : WPA/WPA2-Personal (PSK)

    Read the article

  • Can't Move Windows to 2nd Monitor without Left Mouse and Cntl Key

    - by John C
    I have 2 very frustrating problems that maybe someone can help me with: I have 2 monitors (different sizes and resolutions) setup with the "Extended" monitor Win7 setup. My problem is this = I can not "move" a window from my Primary Monitor (larger and higher resolution on right side in front of me) to my Secondary 2nd monitor (smaller and lower resolution) with just selecting the title bar with the left mouse button and dragging it to the left. Windows 7 "snaps" it back to the left Primary Monitor when the window is physically in the 2nd window area as I'm holding the left mouse button. I can prevent this problem - by holding down the Cntl Key with the Left Mouse button, but this is extremely annoying to me. Also I typically "lose" focus if I try typing input on the 2nd monitor. Typing is erratic with regard to keystroke accuracy from my keyboard translated into input on the 2nd screen. No problem with typing input on the primary left monitor. I find this extremely annoying in Windows 7 and turning off the "snap" feature via the Control panel does NOT work for me. Win7 stubbornly refuses to move my selected window to my 2nd monitor without me "forcing" Win7 to do this with the Cntrl Key. Please tell me this is not a Win7 feature. Also on my system - Windows Key + Shift, Left arrow Key (pressed together) or the same combo with The Right arrow Key - don't do anything whatsoever. Widows Key with "+" however does maximize current window across both monitors, and I can "restore" it with Windows Key and "-" back to original monitor and size. I have tried various solutions including changing the resolutions of one or both of my monitors and sometimes "temporarily helps" but reverts back to the problem. Also if I swap the logical (not physical) layout so that I tell Win7 the monitors are setup in a reserved situation (Large monitor on the left, and small on the right) - this also sometimes helps for awhile - and is very strange and awkward to work with "backwards". But all of these solutions stop working. The only solution that consistently works for "moving" the screens is to hold the Cntrl Key down as I'm moving window with the left mouse selected on the title bar. Even that however, doesn't prevent the loss of typing focus for me on the 2nd monitor - while at the same time the typing on the 1st monitor is fine. Any help on moving my window screens from one monitor on my 2nd monitor without having to press the Cntrl key while holding down my left mouse button with be appreciated. Also any help on gaining typing "focus" into my 2nd screen with be helpful too. Thanks - John

    Read the article

  • What the best way to achieve RPO of zero and lowest possible RTO (less than 15 minutes) with SQL 2008 R2?

    - by Adrian Hope-Bailie
    We are running a payments (EFT transaction processing) application which is processing high volumes of transactions 24/7 and are currently investigating a better way of doing DB replication to our disaster recovery site. Our current and previous strategies have included using both DoubleTake and Redgate to replicate data to a warm stand-by. DoubleTake is the supported solution from the payments software vendor however their (DoubleTake's) support in South Africa is very poor. We had a few issues and simply couldn't ever resolve them so we had to give up on DoubleTake. We have been using Redgate to manually read the data from the primary site (via queries) and write to the DR site but this is: A bad solution Getting the software vendor hot and bothered whenever we have support issues as it has a tendency to interfere with the payment application which is very DB intensive. We recently upgraded the whole system to run on SQL 2008 R2 Enterprise which means we should probably be looking at using some of the built-in replication features. The server has 2 fairly large databases with a mixture of tables containing highly volatile transactional data and pretty static configuration data. Replication would be done over a WAN link to a separate physical site and needs to achieve the following objectives. RPO: Zero loss - This is transactional data with financial impact so we can't lose anything. RTO: Tending to zero - The business depends on our ability to process transactions every minute we are down we are losing money I have looked at a few of the other questions/answers but none meet our case exactly: SQL Server 2008 failover strategy - Log shipping or replication? How to achieve the following RTO & RPO with logshipping only using SQL Server? What is the best of two approaches to achieve DB Replication? My current thinking is that we should use mirroring but I am concerned that for RPO:0 we will need to do delayed commits and this could impact the performance of the primary DB which is not an option. Our current DR process is to: Stop incoming traffic to the primary site and allow all in-flight transaction to complete. Allow the replication to DR to complete. Change network routing to route to DR site. Start all applications and services on the secondary site (Ideally we can change this to a warmer stand-by whereby the applications are already running but not processing any transactions). In other words the DR database needs to, as quickly as possible, catch up with primary and be ready for processing as the new primary. We would then need to be able to reverse this when we are ready to switch back. Is there a better option than mirroring (should we be doing log-shipping too) and can anyone suggest other considerations that we should keep in mind?

    Read the article

  • Windows doesn't get access to internet though linux easily does

    - by flashnik
    We have a very interesting problem. The network is configured in this way: internet is connected to Trendnet switch TS DHCP server at 192.168.0.1 running on Ubuntu (S) is connected to internet switch DNS is also configured on 192.168.0.1 on S D-Link Wi-Fi boosters are connected to switch TS PCs use D-Link PCI-E Wi-Fi cards to get access to network PCs have both Ubuntu and Windows 7 There are about 40 PCs. When PC is booted to Ubuntu it easily gets access to internet. But when it's booted to Windows 7, it gets a valid IP-address, but doesn't get access to internet. The address, mask, DNS, GW-address are totally the same as when it's booted under Ubuntu. The S is reacheble and pingable. Sometimes when we are lucky the PC gets access to Internet, but after rebooting it can lose it. When PC under Windows has access, it has totally the same settings as when it doesn't. What can be done? UPDATE I shared a dropbox with 2 captures of traffic. Ping.pcap is a capture of pinging 8.8.8.8. And google-browser.pcap is a capture of opening a google.com in a browser, both of them are in tcpdump formats and made by Wireshark on Win PC. The MAC of Win PC ends on b7:63 and IP is 192.168.0.130. UPDATE2 This is ifconfig output from Ubuntu Server eth0 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:193.200.211.74 Bcast:193.200.211.78 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe13:d58d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:196284 errors:0 dropped:44 overruns:0 frame:0 TX packets:190682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:158032255 (158.0 MB) TX bytes:156441225 (156.4 MB) Interrupt:19 Memory:c1400000-c1420000 eth0:2 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:192.168.0.1 Bcast:192.168.0.254 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Memory:c1400000-c1420000 eth1 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Memory:c1300000-c1320000 nslookup from Win results in DNS request timeout, nbtstat in 'not found'.

    Read the article

  • Windows 7 & Virtual PC and Internet (gateway) problems on host PC

    - by Mufasa
    I upgraded to Windows 7 on a PC that is a few years old. The CPU was one revision away from having Hyper-V on it. So, I had to install Microsoft Virtual PC 2007 (v6.0.156.0) to run full XP instances instead of the seamless XP virtualization that is advertised so much. That's fine though; the 'older' version is useful since I use it to run different versions of the whole XP/IE stack for testing. (I'm a web developer.) ...And for the one 16-bit application we still use at the office for scheduling. * sigh * The virtual instances work fine, including networking. My issue is that after a reboot or coming out of sleep mode, my host Windows 7 won't connect to the Internet. It will connect to the local network fine. If I disable the "Virtual Machine Network Services" item (I'll call "VMNS" from here on) in the LAN Connection properties box, it starts working. But than the Virtual PC instances lose their network connectivity. If I re-enable VMNS again in the same instance, everything works (Internet on host and in the virtualized instances). But after the next reboot/sleep cycle this starts over. The route table gave me a clue though. When doing a cycle w/ VMNS enabled: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.3.51 20 0.0.0.0 0.0.0.0 10.0.10.10 10.0.3.51 276 ... After VMNS is disabled, the first route goes away. I assume that is for VMNS to intercept virtualized instance's network connections and forward them correctly? Just a guess though. More info: I checked my Firewall settings and Services (because I'm sort of a control nazi and turn off a lot) but couldn't find anything that made sense and if turned on changed anything. So it might be something there I'm missing, but I don't know what. My current hacked solution: So, I figured I'd mess with the routes myself to see if that helped, it did. If I run a route delete 0.0.0.0 on the universal (0.0.0.0) gateway routes, and add back in just the 2nd line with route add 0.0.0.0 mask 0.0.0.0 10.0.10.10--the one that points to my actual gateway (10.0.10.10)--then I don't have to mess with the disable/enable cycle of VMNS, and everything works. Running those two commands is faster then bringing up connection options and disabling and re-enabling VMNS, but I still don't want to have use that hack script every boot either. (Oh, and I also tried messing with hard-coding TCP/IP settings in my network adapter, including setting high metrics, etc., but that didn't help either.) Any suggestions on the right way to fix this?

    Read the article

  • How to make Windows 7 use the internet connection that I specify

    - by user138957
    I have a LAN adapter and a USB wireless internet connection. When both connected windows 7 always uses the USB. I tried changing the metric values but no luck. Let me explains the steps I took. Currently automatic metric on all adapters. LAN connected. ipconfig shows that it is connected to the correct ip/dns/gateway etc. IPv4 Route table shows Metric 24 Then connected USB. ipconfig shows USB connectivity then LAN in that order. Internet is now through USB. IPv4 Route table shows Metric 4249 for LAN and USB is 41. Gateway for USB shows "on-link". netstat -rn shows USBDEVICE on top. Changed LAN metric to 5 and now the route table shows LAN as 9 (not sure why it added 4) and USB as 41. netstat shows LAN then USB. ipconfig shows LAN then USB. But still connection is through USB. How do I know? Task manager shows utilization only through USB as well as speed is showing around 1mbps rather than LANs 10mbps. How can I get win7 use LAN while USB is connected. I am just trying to use USB as a backup just in case I lose LAN connection. Please help!! I thought i will make USB metric manually to say 10. But it says I have to reconnect for it to be effective. Currently USB still shows below LAN and still has 9 and 41 in the table. Disconnected USB. Table shows LAN metric as 24 (Not sure why it got changed from 9 and setting got reverted by to automatic) Reconnected USB. Now in the setting still shows 10 and the route table shows 11 for USB and LAN shows 4249 (settings shows 4245, 4 less)) For some reason restarting USB is resetting LAN setting when reconnected. Thanks

    Read the article

  • Display is slightly blurry on (native) 1920x1080 resolution

    - by Martin Tuskevicius
    I have a computer monitor that is approximately 23" in size. Its native resolution is 1920x1080, and Windows 7 will not allow it to be any higher. However, I cannot make the resolution a little lower as well. When I right-click on my desktop and select 'Screen resolution,' the vertical slider has only two options: 1920x1080 and 1280x720. There are no real problems that I am having besides the fact that the image is slightly blurry. I can easily make things out and see them, but I definitely feel that the image is not as clear as it could be. My graphics card is ATI Radeon HD 5450 and it has the latest graphics drivers installed. I've tried playing around with the AMD VISION Engine Control Center to see if I can change an option to make the image clearer, but I had no luck. I did find one odd thing, though. When I lowered the refresh rate from 60Hz to 50Hz, the image kind of "zoomed in" but it also became perfectly clear like I would expect it to look. The problem is that when I use 50Hz, the image zooms in a little on the center and I lose maybe an inch and a half of the screen (I do not see the bar at the top of applications, I do not see the Windows taskbar thing, etc). I figured if I could somehow zoom in so that the entire image fills the screen (not the slightly cropped version) then I would have the perfectly crisp image of 50Hz, and also the uncropped image of 60Hz. However, upon zooming in, the image began to look blurry again just like it did with 60Hz. So I am at a loss here. I do not know how to make the image look as clear as it should. I have the latest drivers (I updated them today) and I know that my monitor supports the resolution that I am trying to use. Has anybody experienced something like this before? I'd really appreciate any input - thanks! Update: I have figured out how to make the display look crisp! I set it to the 50Hz option, and then I changed the scaling through the monitor itself, rather than software. Now, however, I am finding that games look pretty bad because since it is clear, the lower quality really becomes apparent. I cannot run new games at 1080p, so I run them at the lowest resolution possible (1280x720, since it is the only other option offered, as I have mentioned). So I am wondering, is there a way to have Windows display more resolution options?

    Read the article

  • Reliable file copy (move) process - mostly Unix/Linux

    - by mfinni
    Short story : We have a need for a rock-solid reliable file mover process. We have source directories that are often being written to that we need to move files from. The files come in pairs - a big binary, and a small XML index. We get a CTL file that defines these file bundles. There is a process that operates on the files once they are in the destination directory; that gets rid of them when it's done. Would rsync do the best job, or do we need to get more complex? Long story as follows : We have multiple sources to pull from : one set of directories are on a Windows machine (that does have Cygwin and an SSH daemon), and a whole pile of directories are on a set of SFTP servers (Most of these are also Windows.) Our destinations are a list of directories on AIX servers. We used to use a very reliable Perl script on the Windows/Cygwin machine when it was our only source. However, we're working on getting rid of that machine, and there are other sources now, the SFTP servers, that we cannot presently run our own scripts on. For security reasons, we can't run the copy jobs on our AIX servers - they have no access to the source servers. We currently have a homegrown Java program on a Linux machine that uses SFTP to pull from the various new SFTP source directories, copies to a local tmp directory, verifies that everything is present, then copies that to the AIX machines, and then deletes the files from the source. However, we're finding any number of bugs or poorly-handled error checking. None of us are Java experts, so fixing/improving this may be difficult. Concerns for us are: With a remote source (SFTP), will rsync leave alone any file still being written? Some of these files are large. From reading the docs, it seems like rysnc will be very good about not removing the source until the destination is reliably written. Does anyone have experience confirming or disproving this? Additional info We will be concerned about the ingestion process that operates on the files once they are in the destination directory. We don't want it operating on files while we are in the process of copying them; it waits until the small XML index file is present. Our current copy job are supposed to copy the XML file last. Sometimes the network has problems, sometimes the SFTP source servers crap out on us. Sometimes we typo the config files and a destination directory doesn't exist. We never want to lose a file due to this sort of error. We need good logs If you were presented with this, would you just script up some rsync? Or would you build or buy a tool, and if so, what would it be (or what technologies would it use?) I (and others on my team) are decent with Perl.

    Read the article

< Previous Page | 194 195 196 197 198 199 200 201 202 203 204 205  | Next Page >