Search Results

Search found 64639 results on 2586 pages for 'work stealing'.

Page 20/2586 | < Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >

• help: cannot make ubuntu 64-bit v12.04 install work

  - by honestann

  I decided it was time to update my ubuntu (single boot) computer from 64-bit v10.04 to 64-bit v12.04. Unfortunately, for some reason (or reasons) I just can't make it work. Note that I am attempting a fresh install of 64-bit v12.04 onto a new 3TB hard disk, not an upgrade of the 1TB hard disk that has contained my 64-bit v10.04 installation. To perform the attempted install of v12.04 I unplug the SATA cable from the 1TB drive and plug it into the 3TB drive (to avoid risking damage to my working v10.04 installation). I downloaded the ubuntu 64-bit v12.04 install DVD ISO file (~1.6 GB) from the ubuntu releases webpage and burned it onto a DVD. I have downloaded the DVD ISO file 3 times and burned 3 of these installation DVDs (twice with v10.04 and once with my winxp64 system), but none of them work. I run the "check disk" on the DVDs at the beginning of the installation process to assure the DVD is valid. I also tried to install on two older 250GB seagate drives in the same computer. During every attempt I plug the same SATA cable (sda) into only one disk drive (the 3TB or one of the 250GB drives) and leave the other disk drives unconnected (for simplicity). Installation takes about 30 minutes on the 250GB drives, and about 60 minutes on the 3TB drive - not sure why. When I install on the 250GB drives, the install process finishes, the computer reboots (after the install DVD is removed), but I get a grub error 15. It is my understanding that 64-bit ubuntu (and 64-bit linux in general) has no problem with 3TB disk drives. In the BIOS I have tried having EFI set to "enabled" and "auto" with no apparent difference (no success). I have tried partitioning the drive in a few ways to see if that makes a difference, but so far it has not mattered. Typically I manually create partitions something like this: 8GB swap 8GB /boot ext4 3TB / ext4 But I've also tried the following, just in case it matters: 100MB boot efi 8GB swap 8GB /boot ext4 3TB / ext4 Note: In the partition dialog I specify bootup on the same drive I am partitioning and installing ubuntu v12.04 onto. It is a VERY DANGEROUS FACT that the default for this always comes up with the wrong drive (some other drive, generally the external drive). Unless I'm stupid or misunderstanding something, this is very wrong and very dangerous default behavior. Note: If I connect the SATA cable to the 1TB drive that has been my ubuntu 64-bit v10.04 system drive for the past 2 years, it boots up and runs fine. I guess there must be a log file somewhere, and maybe it gives some hints as to what the problem is. I should be able to boot off the 1TB drive with the 3TB drive connected as a secondary (non-boot) drive and get the log file, assuming there is one and someone tells me the name (and where to find it if the name is very generic). After installation on the 3TB drive completes and the system reboots, the following prints out on a black screen: Loading Operating System ... Boot from CD/DVD : Boot from CD/DVD : error: unknown filesystem grub rescue Note: I have two DVD burners in the system, hence the duplicate line above. The same install and reboot on the 250GB drives generates "grub error 15". Sigh. Any ideas? ========== motherboard == gigabyte 990FXA-UD7 CPU == AMD FX-8150 8-core bulldozer @ 3.6 GHz RAM == 8GB of DDR3 in 2 sticks (matched pair) HDD == seagate 3TB SATA3 @ 7200 rpm (new install 64-bit v12.04) HDD == seagate 1TB SATA3 @ 7200 rpm (current install 64-bit v10.04) GPU == nvidia GTX-285 ??? == no overclocking or other funky business USB == external seagate 2TB HDD for making backups DVD == one bluray burner (SATA) DVD == one DVD burner (SATA) The current ubuntu 64-bit v10.04 system boots and runs fine on a seagate 1TB.

  Read the article

• Building on someone else's DefaultButton Silverlight work...

  - by KyleBurns

  This week I was handed a "simple" requirement - have a search screen execute its search when the user pressed the Enter key instead of having to move hands from keyboard to mouse and click Search.  That is a reasonable request that has been met for years both in Windows and Web apps.  I did a quick scan for code to pilfer and found Patrick Cauldwell's Blog posting "A 'Default Button' In Silverlight".  This posting was a great start and I'm glad that the basic work had been done for me, but I ran into one issue - when using bound textboxes (I'm a die-hard MVVM enthusiast when it comes to Silverlight development), the search was being executed before the textbox I was in when the Enter key was pressed updated its bindings.  With a little bit of reflection work, I think I have found a good generic solution that builds upon Patrick's to make it more binding-friendly.  Also, I wanted to set the DefaultButton at a higher level than on each TextBox (or other control for that matter), so the use of mine is intended to be set somewhere such as the LayoutRoot or other high level control and will apply to all controls beneath it in the control tree.  I haven't tested this on controls that treat the Enter key special themselves in the mix. The real change from Patrick's solution here is that in the KeyUp event, I grab the source of the KeyUp event (in my case the textbox containing search criteria) and loop through the static fields on the element's type looking for DependencyProperty instances.  When I find a DependencyProperty, I grab the value and query for bindings.  Each time I find a binding, UpdateSource is called to make sure anything bound to any property of the field has the opportunity to update before the action represented by the DefaultButton is executed. Here's the code: public class DefaultButtonService { public static DependencyProperty DefaultButtonProperty = DependencyProperty.RegisterAttached("DefaultButton", typeof (Button), typeof (DefaultButtonService), new PropertyMetadata (null, DefaultButtonChanged)); private static void DefaultButtonChanged(DependencyObject d, DependencyPropertyChangedEventArgs e) { var uiElement = d as UIElement; var button = e.NewValue as Button; if (uiElement != null && button != null) { uiElement.KeyUp += (sender, arg) => { if (arg.Key == Key.Enter) { var element = arg.OriginalSource as FrameworkElement; if (element != null) { UpdateBindings(element); } if (button.IsEnabled) { button.Focus(); var peer = new ButtonAutomationPeer(button); var invokeProv = peer.GetPattern(PatternInterface.Invoke) as IInvokeProvider; if (invokeProv != null) invokeProv.Invoke(); arg.Handled = true; } } }; } } public static DefaultButtonService GetDefaultButton(UIElement obj) { return (DefaultButtonService) obj.GetValue(DefaultButtonProperty); } public static void SetDefaultButton(DependencyObject obj, DefaultButtonService button) { obj.SetValue(DefaultButtonProperty, button); } public static void UpdateBindings(FrameworkElement element) { element.GetType().GetFields(BindingFlags.Public | BindingFlags.Static).ForEach(field => { if (field.FieldType.IsAssignableFrom(typeof(DependencyProperty))) { try { var dp = field.GetValue(null) as DependencyProperty; if (dp != null) { var binding = element.GetBindingExpression(dp); if (binding != null) { binding.UpdateSource(); } } } // ReSharper disable EmptyGeneralCatchClause catch (Exception) // ReSharper restore EmptyGeneralCatchClause { // swallow exceptions } } }); } }

  Read the article

• (libgdx) Button doesn't work

  - by StercoreCode

  At the game I choose StopScreen. At this screen displays button. But if I click it - it doesn't work. What I expect - when I press button it must restart game. At this stage must display at least a message that the button is pressed. I tried to create new and clear project. Main class implement ApplicationListener. I put the same code in the appropriate methods. And it's works! But if i create this button in my game - it doesn't work. When i play and go to the StopScreen, i saw button. But if i click, or touch, nothing happens. I think that the proplem at the InputListener, although i set the stage as InputProcessor. Gdx.input.setInputProcessor(stage); I also try to addListener for Button as ClickListener. But it gave no results. Or it maybe problem that i implements Screen method - not ApplicationListener or Game. But if StopScreen implement ApplicationListener, at the mainGame I can't to setScreen. Just interests question: why button displays but nothing happens to it? Here is the code of StopScreen if it helps find my mistake: public class StopScreen implements Screen{ private OrthographicCamera camera; private SpriteBatch batch; public Stage stage; //** stage holds the Button **// private BitmapFont font; //** same as that used in Tut 7 **// private TextureAtlas buttonsAtlas; //** image of buttons **// private Skin buttonSkin; //** images are used as skins of the button **// public TextButton button; //** the button - the only actor in program **// public StopScreen(CurrusGame currusGame) { camera = new OrthographicCamera(); camera.setToOrtho(false, 800, 480); batch = new SpriteBatch(); buttonsAtlas = new TextureAtlas("button.pack"); //** button atlas image **// buttonSkin = new Skin(); buttonSkin.addRegions(buttonsAtlas); //** skins for on and off **// font = AssetLoader.font; //** font **// stage = new Stage(); stage.clear(); Gdx.input.setInputProcessor(stage); TextButton.TextButtonStyle style = new TextButton.TextButtonStyle(); style.up = buttonSkin.getDrawable("ButtonOff"); style.down = buttonSkin.getDrawable("ButtonOn"); style.font = font; button = new TextButton("PRESS ME", style); //** Button text and style **// button.setPosition(100, 100); //** Button location **// button.setHeight(100); //** Button Height **// button.setWidth(100); //** Button Width **// button.addListener(new InputListener() { public boolean touchDown(InputEvent event, float x, float y, int pointer, int button) { Gdx.app.log("my app", "Pressed"); return true; } public void touchUp(InputEvent event, float x, float y, int pointer, int button) { Gdx.app.log("my app", "Released"); } }); stage.addActor(button); } @Override public void render(float delta) { Gdx.gl.glClearColor(0, 1, 0, 1); Gdx.gl.glClear(GL20.GL_COLOR_BUFFER_BIT); stage.act(); batch.setProjectionMatrix(camera.combined); batch.begin(); stage.draw(); batch.end(); }

  Read the article

• Upgraded to 12.04 now wifi doesn't work

  - by Benito Kestelman

  My laptop's wifi stopped working when I upgraded to Ubuntu 12.04 (wired works). I just reinstalled 12.04 over my old 12.04 on which wifi didn't work either in an attempt to restore any settings I may have accidentally changed, but it still doesn't work. I also used a wired connection to install updates in case this bug has been fixed, but it has not. Here is the result of sudo lshw -class network: *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:5f:5b:f4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-29-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 14:da:e9:c0:da:78 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) Here is rfkill list all: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-wimax: WiMAX Soft blocked: no Hard blocked: no lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 8087:07d6 Intel Corp. Bus 001 Device 004: ID 13d3:5710 IMC Networks Bus 002 Device 003: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Bluetooth Bus 003 Device 003: ID 0781:5530 SanDisk Corp. Cruzer lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) 03:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller 04:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0)

  Read the article

• Macbook pro 8,1 ubuntu 12.04 sd card reader doesnt work

  - by mandy

  THe built in sd card reader on the macbook pro 8,1 (2011, early or mid i think) doesnt work AT ALL. However i read here.... https://bugs.launchpad.net/ubuntu/+source/linux/+bug/801034 that someone plugged in ethernet and it works. How the hell does that make a difference? There has to be some kind of better workaround? I take my laptop on the go, thats why i bought a LAPTOP. I dont want to be tethered down. Please help?

  Read the article

• Installing skype will not work - skype-bin not installable, and 'held broken packages'

  - by Michionlion

  So, I am trying to install skype through apt-get, but after running into this problem multiple times, and trying to find a solution, it still doesn't work... I tried all the answers here: Installing Skype on 12.04 64 bit causes errors, but I still get the error. (my problem is exactly the same as that one, too) I even went and edited the package status thing manually, and removed all references to 'skype' or 'skype-bin'. I still get the problem... I'm running ubuntu 12.10, as a dual-boot with windows 7. It's a 64-bit computer.

  Read the article

• Which LAN card / module combinations proven to work with Wake on LAN

  - by pablomo

  I've got a 12.04 headless server that I've been trying to get to work with wake-on-lan. The card is Marvel 88E8053 using the sky2 module. Although WOL is enabled in BIOS and ethtool shows the card as WOL enabled, it refuses to wake when I send the magic packet. I have verified that the packet is being received OK when the machine is on. The machine does wake OK from a BIOS alarm which suggests it is a network card issue. I've seen reference to bugs in sky2 that mean WOL fails in recent versions of Ubuntu (and have tried a module conf file as suggested here but to no avail) So I am thinking the best bet is to replace the ethernet card with one that definitely works with WOL in 12.04 - please could you post your card make and model no if you are using it successfully?

  Read the article

• What Agile Model do you use at Work?

  - by Kyle Rozendo

  I am looking to start pushing for more Agile processes to be brought into play in the work place and do my best to outlaw cowboy coding as much as possible. I understand many of the different models and am just looking to see which model has the higher uptake (or which parts of the model as well), and in what industry it is being used. Extreme Programming (XP) Adaptive Software Development (ASD) Scrum Dynamic Systems Development Model (DSDM) Crystal Feature Driven Development (FDD) Lean Software Development (LSD) Agile Modelling (AM) Agile Unified Process (AUP) Kanban If you care to add to your answer with comments about what you don't like, do like or have tried and it hadn't worked, that would also be appreciated.

  Read the article

• Running Unity 2d - Does not work on actual system but works fine in VM

  - by Dylan

  So I'm running Ubuntu 10.10 and I cannot get Unity 2d to work with my system. This is particularly frustrating as it works just fine in all the VMs I've tested it on. I actually really like Unity and I want to get to know it (in part) before Ubuntu 11.04. I checked Synaptic and it looks like everything's there. The only thing not installed are dev libs and so on. Should I install those as well? Obviously the difference between my system and a VM is that the VM is running off a basically brand new OS. I only use VMs to test new stuff out and remake them often, so my only guess is that I have something installed on my system that is preventing Unity from running. Any thoughts?

  Read the article

• How Lead-Acid Batteries Work [Video]

  - by Jason Fitzpatrick

  Every morning when you go out and start your car, you’re pulling power from a lead-acid battery. But how exactly do they work? In this informative video we see how lead plates and sulfuric acid provide the power your car craves. Courtesy of Engineer Guy Video: Bill explains the essential principles of a lead-acid battery. He shows the inside of motorcycle lead-acid battery, removes the lead and lead-oxide plates and shows how they generate a 2 volt potential difference when placed in sulfuric acid. He explains how the build up of lead sulfate between the plates will make the battery unusable if it discharged completely, which leads him to a description of how to make a deep cycle battery used for collecting solar energy. [via Make] How to Use an Xbox 360 Controller On Your Windows PC Download the Official How-To Geek Trivia App for Windows 8 How to Banish Duplicate Photos with VisiPic

  Read the article

• How do software updates work?

  - by Jonas

  I would like to know how software updates work for my Ubuntu Server 10.10. I have been recommended to use apt-get install for installing new software and apt-get update for updating software for a Ubuntu Server in production use. Because these packages are tested for Ubuntu in contrast to download source code and compile the software on the box. But on my Ubuntu Server 10.10, I don't get the latest stable version of PostgreSQL (9) or the latest stable version of Nginx (8) using apt-get install. So how is this working, will these software be updated when I later run apt-get update or do I have to later run apt-get install again, or do I have to wait for the next release of Ubuntu to get them? And are patches and security updates managed in the same way? Or can they be updated automatically? If there is such a setting, how do I check what my system is using?

  Read the article

• Rails noob - How to work on data stored in models

  - by Raghav Kanwal

  I'm a beginner to Ruby and Rails, and I have made a couple applications like a Microposts clone and a Todo-List for starters, but I'm starting work on another project. I've got 2 models - user and tracker, you log in via the username which is authenticated and you can log down data which is stored in the tracker table. The tracker has a column named "Calories" and I would like Rails to sum all of the values entered if they are on the same date, and output the result which is subtracted from, say 3000 in a new statement after the display of the model. I know what I'm talking about is just ruby code, im just not sure how to incorporate it. :( Could someone please guide me through this? And also link me to some guides/tutorials which teach working on data from models? Thank you :)

  Read the article

• How do software updates work on Ubuntu?

  - by Jonas

  I would like to know how software updates work for my Ubuntu Server 10.10. I have been recommended to use apt-get install for installing new software and apt-get update for updating software for a Ubuntu Server in production use. Because these packages are tested for Ubuntu in contrast to download source code and compile the software on the box. But on my Ubuntu Server 10.10, I don't get the latest stable version of PostgreSQL (9) or the latest stable version of Nginx (8) using apt-get install. So how is this working, will these software be updated when I later run apt-get update or do I have to later run apt-get install again, or do I have to wait for the next release of Ubuntu to get them? And are patches and security updates managed in the same way? Or can they be updated automatically? If there is such a setting, how do I check what my system is using?

  Read the article

• Check your Embed Interop Types flag when doing Visual Studio extensibility work

  - by Daniel Cazzulino

  In case you didn’t notice, VS2010 adds a new property to assembly references in the properties window: Embed Interop Types: This property was introduced as a way to overcome the pain of deploying Primary Interop Assemblies. Read that blog post, it will help understand why you DON’T need it when doing VS extensibility (VSX) work. It's generally advisable when doing VSX development NOT to use Embed Interop Types, which is a feature intended mostly for office PIA scenarios where the PIA assemblies are HUGE and had to be shipped with your app. This is NEVER the case with VSX authoring. All interop assemblies you reference (EnvDTE, VS.Shell, etc.) are ALWAYS already there in the users' machine, and you NEVER need to distribute them. So embedding those types only increases your assembly size without a single benefit to you (the extension developer/author).... Read full article

  Read the article

• HTG Explains: How Software Installation & Package Managers Work On Linux

  - by Chris Hoffman

  Installing software on Linux involves package managers and software repositories, not downloading and running .exe files from websites like on Windows. If you’re new to Linux, this can seem like a dramatic culture shift. While you can compile and install everything yourself on Linux, package managers are designed to do all the work for you. Using a package manager makes installing and updating software easier than on Windows. How to Banish Duplicate Photos with VisiPic How to Make Your Laptop Choose a Wired Connection Instead of Wireless HTG Explains: What Is Two-Factor Authentication and Should I Be Using It?

  Read the article

• GPL: does one line of GPLed code make program a "derived work"

  - by SigTerm

  I've recently run into some argument with a person that claims to be a lawyer (I have my suspicions about this not being completely true, though). As far as I know, copying even one line of code from GPLed program into proprietary body of code requires you to release the whole thing under GPL, if you ever decide to publish the software and make it available to the public. The person in question claims that it is "absurd" (I know it is, but AFAIK that's how GPL works), it is "redefining the copyright", "GPL has no power to do that", and claiming that "one line of GPLed code makes you release the whole thing under GPL" is absurd. That contradicts the GPL FAQ. Can somebody clarify the situation? Am I right in assumption that copying even smallest subroutine from GPL program into your code automatically makes your program a "derived work" which means you are obliged to release it under GPL license if you publish it?

  Read the article

• Proper attribution of derived work in a GPL project

  - by Anton Gogolev

  This is a continuation of me rewriting GPL project. What will be the correct way of attributing my project as being a derivative of some other GPL-licensed project? So far I came up with: HgSharp Original Copyright Matt Mackall <[email protected]> and contributors. The following code is a derivative work of the code from the Mercurial project, which is licensed GPLv2. This code therefore is also licensed under the terms of the GNU Public License, verison 2. For information on the license of this code when distributed with and used in conjunction with the other modules in the HgSharp project, please see the root-level COPYING file. Copyright 2011-2012 Anton Gogolev <[email protected]>

  Read the article

• DNS records: make mydomain.com work without www

  - by brentonstrine

  I am trying to configure DNS on my domain, however, I can only get it to work with the www prefix. Right now I have the following DNS A records: @ A 123.456.789 www A 123.456.789 http://www.mydomain.com works perfectly. But http://mydomain.com fails. I've tried all of the following: mydomain.com A 123.456.789 mydomain A 123.456.789 * A 123.456.789 But it always goes to port :80 requires a username and password. Except now it's somehow being redirected to a spammers website.

  Read the article

• Apache wont work after changing port

  - by user73595

  I am working with ubuntu 12.04 server 64-bit edition. I have intalled apache2 without any problems and i can see the "It works" message. And i can also access from other pc within the network. I want to host my website using home DSL, However i found out that my ISP is blocking the port 80, 25 ,110 so i changed the port to 8010 (/etc/apache2/port.conf) After this I am unable to get the "It Works" web page. All it shows that "NOT FOUND" i tried with ipaddress:8010 and it doesnot work with both internal and also external.

  Read the article

• Can't make the Multimedia keys work in LXDE

  - by Uri Herrera

  I've tried to edit the configuration file in ~/.config/openbox/lxde-rc.xml however the changes don't take effect, i still can't use the keys. The LXDE wiki shows that after finding that my keyboard sends the correct standardized keyboard events i should go and edit the file to my liking, the keyboard does send the correct events and the keys are properly identified yet nothing happens. Since LXDE doesn't come with a sound preferences option i have installed xfce4-mixer. I too have a netbook running Lubuntu and it's media keys are working fine, i don't know if what i installed has had something to do here?. I also installed xfce4-volumed volume keys daemon from synaptic but to no avail, still nothing. How can i make the multimedia keys of my keyboard work in LXDE with xfce4-mixer Edit: Here is my lxde-rc.xml file

  Read the article

• Should I work on CSS or apps first?

  - by Fred

  I am working on my own website for my business, and I need to contract out some assistance. For example, I have the site looking pretty good on Firefox, but it needs help on other browsers. I also need some help with adding some Django apps to the site and setting up a database. I plan to seek the help of two different individuals via elance or odesk. My question is which to do first - get the css and html right then do the apps, or get the apps done and then work on the css and html? Thanks in advance for any suggestions.

  Read the article

• Printing multiple pages per sheet doesn't work

  - by Ricky Robinson

  In Ubuntu 12.04, I added a network printer which I had previously used without any problems on a different machine (with the same release of Ubuntu). Now, with the default generic driver installed, printing multiple pages per sheet from evince doesn't work properly. If I select 2 per sheet, be it long or short edge, it always prints 4. Why is this? It used to happen with non-pdf documents in the past, like from a browser. My workaround was to print to pdf file and then print the pdf itself. Now I'm clueless... Edit: the same happens with a different network printer, in which I installed the driver specific to its particular model.

  Read the article

• Thinkpad x201 Tablet - Touch doesn't work correctly under 12.04

  - by Joachim

  running 12.04 on my Thinkpad X201t. On the login screen the touch works fine, the mouse cursor appears where I touch the screen. After I logged in, it doesn't work anymore. If I touch the display, the cursor stays on the point where it was before, it doesn't jump to the touchpoint. I can move it, yes, but its chaotic. With the pen it works fine, but without the touch-function it's not enought for real tablet usage. So, would be glad if touch-function can be fixed. I'm very new to Linux/Ubuntu, so don't know where I can start. Haven't found anything in the system settings & Compiz so far, also no luck in google etc. Would be glad for help ;-). Of course I could go back to 11.04... but I would prefer to stay with the new system. Best, Joachim

  Read the article

• Dealing with a developer continuously ignoring edge cases in his work

  - by Alex N.

  I have an interesting, fairly common I guess, issue with one of the developers in my team. The guy is a great developer, work fast and productive, produces fairly good quality code and all. Good engineer. But there is a problem with him - very often he fails to address edge cases in his code. We spoke with him about it many times and he is trying but I guess he just doesn't think this way. So what ends up happening is that QA would find plenty issues with his code and return it back for development again and again, ultimately resulting in missed deadlines and everyone in the team unhappy. I don't know what to do with him and how to help him overcome this problem. Perhaps someone with more experience could advise? Thank you!

  Read the article

• How do you make Bastille work and secure Ubuntu 12.04? It doesnt work for me `sudo bastille -x`

  - by BobMil

  I was able to install bastille from the normal repositories and then run the GUI. After going through the options and clicking OK to apply, it showed these errors. Do you know why Bastille wont work on Ubuntu 12.04? NOTE: Executing PSAD Specific Configuration NOTE: Executing File Permissions Specific Configuration NOTE: Executing Account Security Specific Configuration NOTE: Executing Boot Security Specific Configuration ERROR: Unable to open /etc/inittab as the swap file /etc/inittab.bastille already exists. Rename the swap file to allow Bastille to make desired file modifications. ERROR: open /etc/inittab.bastille failed... ERROR: open /etc/inittab failed. ERROR: Couldn't insert line to /etc/inittab, since open failed.NOTE: Executing Inetd Specific Configuration

  Read the article

< Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >