Search Results

Search found 11207 results on 449 pages for 'ip ban'.

Page 205/449 | < Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >

• How do I configure networking when using XEN on 12.04 Server

  - by Ingram

  I'm following this guide, https://help.ubuntu.com/community/XenProposed, and I'd like to setup a static IP address, but I don't know how. I'm using 12.04 Server. This is the step I'm having trouble at (I'm using eth1): Edit /etc/network/interfaces, and make it look like this: auto lo iface lo inet loopback auto xenbr0 iface xenbr0 inet dhcp bridge_ports eth0 auto eth0 iface eth0 inet manual I do this, and here is my output from ifconfig: eth1 Link encap:Ethernet HWaddr 00:17:a4:f8:79:20 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:478264 errors:0 dropped:0 overruns:0 frame:0 TX packets:2895 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:46470058 (46.4 MB) TX bytes:214620 (214.6 KB) Interrupt:17 Memory:fa000000-fa012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) xenbr0 Link encap:Ethernet HWaddr 00:17:a4:f8:79:20 inet addr:192.168.1.122 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::217:a4ff:fef8:7920/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:471842 errors:0 dropped:0 overruns:0 frame:0 TX packets:2795 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:37005780 (37.0 MB) TX bytes:182010 (182.0 KB) So how do I give this system a static IP address? Sorry, I'm not that familiar with networking on Ubuntu.

  Read the article

• Get to Know a Candidate (5 of 25): Jim Carlson&ndash;Grassroots Party

  - by Brian Lanham

  DISCLAIMER: This is not a post about “Romney” or “Obama”. This is not a post for whom I am voting. Information sourced for Wikipedia. Carlson is an American businessman and the Grassroots Party nominee. Carlson is the owner of Last Place on Earth, a head shop located in Duluth, Minnesota. In September 2011, the shop was raided by police for selling bath salts and synthetic marijuana. After the raid, Carlson filed a lawsuit to strike down Minnesota's ban on the substances. His suit was dismissed by the court in November 2011. The Grassroots Party was created in the 1980s to oppose drug prohibition.  The party shares many of the the political leftist values of the Green Party but with a greater emphasis on marijuana/hemp legalization issues.  The permanent platform of the Grassroots Party is the Bill of Rights. Individual candidate's positions on issues vary from Libertarian to Green. All Grassroots candidates would end marijuana/hemp prohibition and re-legalize Cannabis for all its uses. Learn more about Jim Carlson and Grassroots Party on Wikipedia.

  Read the article

• Why does modx-based site start using different domains for some content?

  - by naxa

  situation I have a modx site on a VPS with multiple domain and subdomain names. The modx site should use what I call the 'primary' domain name's 'primary' subdomain, ie www.intendedname.tld . The problem is that as time pass, the site mysteriously starts using another subdomain for links to content like videos, images, and even pages and (internal) links. The other subdomains doesn't serve this content of course. If I clear the modx cache, the original state is restored. However, the problem comes back again later. The VPS has a domain registered and multiple A records pointing to the VPS's IP, as subdomains. There is the 'primary' whan which is intended to be used as the public content server, the other ones are like docs. and test., etc. On top of that, I have dynamic-dns service client installed from no-ip on the machine and a dynamic domain-name bound. It gives a completely different domain name. I originally used it for ssh login and to serve a completely different site. An nginx server is put into good use to do rewrite the different subdomains to the right places. edit The modx templates use Templates use <base href="[[++site_url]]" />. current attempt to fix The current 'solution' to the problem is to also use the rewrite to rewrite everything to the 'primary' domain and subdomain. In the nginx config file for the site, it utilizes (unsurprisingly) the rewrite directive to rewrite the unexpected server_name entries (ie. the other subdomains) in a server block dedicated to this task. So with this, the main site basically works (sort of) but this renders all the other functions (docs) useless. Before this rewrite was set, the 'solution' was to clear the modx cache on a regular basis. The original modx content is not getting corrupted, only the files in cache are. What can I do to find out what actual the problem is and fix it?

  Read the article

• Host is unreacheble with static networking configuration via /etc/network/interfaces while GUI NetworkManager is ok

  - by Riccardo

  I have some trouble setting-up the network interface using the static IP configuration. I run ubuntu 12.04 kernel 3.11.0-22 with the back-ports enabled. I followed these instructions from help.ubuntu.com but there seems to exist some conflict between the GUI approach (NetworkManager) and the command line approach. $ sudo nano /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 10.1.1.50 gateway 10.1.1.10 netmask 255.255.255.0 dns-nameservers 192.168.3.45 192.168.8.10 $ sudo /etc/init.d/networking restart I than try to ping for example google.com ping -c 3 www.google.com the response is that the host is unreachable. The icon on the top right of the desktop says: wired network disconnected. If I work using the GUI approach (Edit Connections and so on...) all works great. Can same one explain to me where I wrong? $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 90:e6:ba:07:4a:77 inet addr:10.1.1.50 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::92e6:baff:fe07:4a77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39619 errors:0 dropped:0 overruns:0 frame:0 TX packets:18520 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:19030895 (19.0 MB) TX bytes:2768769 (2.7 MB) $ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0

  Read the article

• Apache (XAMPP 1.8.0) access.log/Intrusion Detection Concern

  - by Andy Holaday

  [I originally posted on SO but it earned me a Tumbleweed badge. This looks like a better venue for the question.] I have Apache (XAMPP 1.8.0) running on Vista Pro x64. A couple times now I have seen a pattern like the example below in access.log. Concerning is the "attack" seems to somehow shift from a public IP to a valid private IP on my network (happens to be the WAN address of one of my routers). Two questions: How is this possible, and what happens if the "attacker" stumbles on a valid request? I've googled this to no avail. 177.0.X.X - - [03/Jun/2012:08:19:34 -0400] "GET /phpMyAdmin-2.5.4/index.php HTTP/1.1" 403 177.0.X.X - - [03/Jun/2012:08:19:34 -0400] "GET /phpMyAdmin-2.5.5-rc1/index.php HTTP/1.1" 403 177.0.X.X - - [03/Jun/2012:08:19:34 -0400] "GET /phpMyAdmin-2.2.6/index.php HTTP/1.1" 403 177.0.X.X - - [03/Jun/2012:08:19:34 -0400] "GET /phpMyAdmin-2.5.5-rc2/index.php HTTP/1.1" 403 192.168.15.3 - - [03/Jun/2012:08:19:56 -0400] "GET /phpMyAdmin-2.5.6-rc2/index.php HTTP/1.1" 403 177.0.X.X - - [03/Jun/2012:08:19:56 -0400] "GET /phpMyAdmin-2.5.6-rc1/index.php HTTP/1.1" 403 177.0.X.X - - [03/Jun/2012:08:19:56 -0400] "GET /phpMyAdmin-2.5.5-pl1/index.php HTTP/1.1" 403 192.168.15.3 - - [03/Jun/2012:08:19:59 -0400] "GET /phpMyAdmin-2.5.7/index.php HTTP/1.1" 403 192.168.15.3 - - [03/Jun/2012:08:20:01 -0400] "GET /phpMyAdmin-2.5.7-pl1/index.php HTTP/1.1" 403 192.168.15.3 - - [03/Jun/2012:08:20:02 -0400] "GET HTTP/1.1" 400 1060 "-" "-"

  Read the article

• Site in subdomain (MaraDNS + Nginx)

  - by Grzegorz

  Welcome, Actually I'm doing some experiments on my VPS with Ubuntu. I've installed MaraDNS with Nginx. At this moment I've correctly launch static site which is available from Internet (maindomain.com). In next step I want to add new site which will be available in subdomain, for example dev.maindomain.com. I've tried to db.maindomain.com file (used by MaraDNS): maindomain.com. xxx.xxx.xxx.xxx www.maindomain.com. CNAME maindomain.com. dev.maindomain.com. xxx.xxx.xxx.xxx Where xxx.xxx.xxx.xxx is VPS IP address. In nginx.conf I have: server { listen 80; server_name maindomain.com; access_log /var/log/nginx/maindomain.com.log location / { root /var/www/maindomain.com; index index.html; } } server { listen 80; server_name dev.maindomain.com; access_log /var/log/nginx/dev.maindomain.com.log location / { root /var/www/dev.maindomain.com; index index.html; } } With this configuration maindomain.com works properly, but dev.maindomain.com isn't available. When I try: ping dev.maindomain.com then I get my xxx.xxx.xxx.xxx IP. Do you have any suggestions how can I resolve this problem?

  Read the article

• Apache HTTPS ProxyPass certificate location

  - by oz1cz

  I'm trying to set up an Apache server that uses ProxyPass to pass HTTPS requests on to another server. Let's call the proxy server ALPHA and the target server BETA. ALPHA does not run HTTPS, but BETA does. I first tried using this virtual host specification on ALPHA: <VirtualHost *:443> ServerName mysite.com ProxyPass / https://192.168.1.105/ # BETA's IP address ProxyPassReverse / https://192.168.1.105/ # BETA's IP address ProxyPreserveHost On ProxyTimeout 600 SSLProxyEngine On RequestHeader set Front-End-Https "On" CacheDisable * </VirtualHost> But when I tried this, Apache complained saying, "[error] Server should be SSL-aware but has no certificate configured [Hint: SSLCertificateFile]". I had to copy the SSL certificate from BETA to ALPHA and add these lines to the host specification on ALPHA: SSLEngine on SSLCertificateKeyFile /usr/local/ssl/private/BETA_private.key SSLCertificateFile /usr/local/ssl/crt/BETA_public.crt SSLCertificateChainFile /usr/local/ssl/crt/BETA_intermediate.crt Now the system works. But I have a feeling that I have done something wrong or unnecessary. I have the web site's private key and certificate lying on both ALPHA and BETA. Is that necessary? Should I have done it differently?

  Read the article

• Dual LAN Printing

  - by Christopher

  I want to use Ubuntu 10.10 Server in a classroom, a computer lab whose bandwidth is provided by a local cable ISP. That's no problem, though the school network has an IP printer that I want to use. I cannot reach the printer through the cable Internet. But, I have two network cards. How is it possible to use both networks at once? eth0 (static 192.168.1.254) is plugged into a four-port router, 192.168.1.1. On the public side of the four-port router is Internet provided by the cable company. I also have the classroom workstations plugged into a switch. The switch is plugged into the four-port router. The whole classroom is wired into the cable Internet. The other NIC, eth1, could it be plugged into an Ethernet jack in the wall? It uses the school network, and I might receive by DHCP an IP address like 10.140.10.100, with the printer on maybe 10.120.50.10. I was thinking about installing the printer on the server so that it could be shared with the workstations. But how does this work? Can I just plug eth1 into the school network and access both LANs? Thanks for any insight, Chris

  Read the article

• Bizarre image loading problem from apache2

  - by NateDSaint

  Users have complained a few times about seeing a bizarre set of pink or green stripes on our webpage. At first I thought there were a rash of video card outages, but then someone sent me a screenshot from their browser (IE8). I later saw the same thing, but with slightly different colors on Chrome. Users have experienced this on their iPads and iPhones (iOS Safari). Because I've optimized the site to cache images, the bad image stays around until you clear your cache, so once you do, it resolves itself. My assumption is that the transmission of the image is being cut off mid-stream and then staying that way, but I can't for the life of me figure out why. Here's what I've checked: Header length is being sent, and transmission looks okay (wget sample below): wget http://www.superiorlivestock.com/templates/sla2/images/wallbg2.jpg --2012-04-05 08:46:00-- http://www.superiorlivestock.com/templates/sla2/images/wallbg2.jpg Resolving www.superiorlivestock.com (www.superiorlivestock.com)... [ip redacted] Connecting to www.superiorlivestock.com (www.superiorlivestock.com)|[ip redacted]|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 45926 (45K) [image/jpeg] Saving to: `wallbg2.jpg' Images are not being served gzipped (apache conf below): SetOutputFilter DEFLATE SetEnvIfNoCase Request_URI \.(?:gif|jpe?g|png)$ no-gzip dont-vary The site is www.superiorlivestock.com, and here's a sample of the bad page load: Is there something obvious I'm missing? Am I saving my images in the wrong format somehow?

  Read the article

• Adsense click bot is click bombing my site

  - by Graham

  I have a site that get's roughly 7,000 - 10,000 page views per day right now. Starting around 1 AM on 7/1/12 I noticed the CTR was rising dramatically. These clicks would be credited then de-credited soon after. So, they were obviously fraudulent clicks. The next day I had about 200 clicks in account with about 100 of them being fraudulent. It's about 3 - 8 per hour evenly dispersed for each of the three ads 24 hours a day. This leads me to believe that it's some sort of Adsense click bot. Also, I removed the ads last evening then put them back up around 3AM and the invalid clicks started within 10 minutes. I signed up for statcounter.com to analyze the exit links on the Adsense. Then I conditionally blocked ads for the IP address of the person / bot I suspected doing this. But, I think that the bot has several proxies to choose from and can refresh IP addresses. I've notified Google through the invalid click form / email 4 times over the past two days in order to let them know I'm aware of the situation and am working on a solution. I've also temporally removed all ads on that site. How can I block a bot like this? Thank you.

  Read the article

• Recommendations for managing DNS issues when hosting customer sites.

  - by Thomas

  I'm working at a company which primarily provides SaaS products but also will host some of our customers corporate websites. My question relates to recommendations for managing DNS for client's domain names. My objectives: Not restrict my ability to change the server's IP address such as might happen when I move my servers to a new host. Not have to contact the customer to change their domain's DNS if I need to change the server's IP address. Often times, customers lose this information or have to track down the one person with any knowledge of the domain settings. Map both .clientdomain.com and www.clientdomain.com to the proper IIS site. However, I'm running into a couple of common problems: Sometimes, the DNS console provided by the client's hosting company does not allow for CNAME records. Sometimes, the DNS console provided by the client's hosting company will not let me create a CNAME entry for .spiffydomain.com because the given hosting company has created a SOA record for that entry or simply requires that .spiffydomain.com be an A record. I believe one solution to #2 is to use a wildcard for a CNAME entry (i.e. *.spiffydomain.com). Is that correct? How do other folks that are hosting many customer's site manage change of DNS entries on their servers?

  Read the article

• Can not access Internet (DNS names do not resolve) after update today

  - by Aras

  I have been using Precise for a few weeks now for work with no problem. Today, I am not able to access any website using either wired or wireless connections. I installed the updates today which included nautilus, xserver, and a new kernel (3.2.0-24). After restarting I no longer was able to browse the Internet using firefox or chrome. Trying to ping google in terminal gives ping: unknown host google.ca I have tried: Connecting to wireless or wired networks (both working on other machines) Restart the machine and boot with previous Kernel Manually configure opendns on my wired connection Restart the network and the laptop and the wireless card Without any success so far. I am not sure where to go next. Please let me know the cause of the issue or help me troubleshoot it. Note that the laptop does receive an ip address, and it can ping ip address of google.ca (74.125.127.94) but not the domain name, or any domain name for that matter. This system was upgraded from 11.10 to 12.04 more two weeks ago.

  Read the article

• Changing frontend cache

  - by Utsav

  Our architecture consists of a front-end cache that most read only users obtain their data from directly. The front-end cache sits in front of a farm of webservers that serve pages written in PHP. We need to be able to detect certain conditions at the front-end cache level and pass those values through to the back-end via HTTP headers. For example we would like to manually tag the carrier network based on the IP address. So, for incoming traffic if the user is say coming from an IP address in the range of "41.202.192.0"/19 we would tag them as being a Orange Cameroon user by setting the appropriate HTTP request header, e.g., X-Carrier = "Orange Cameroon". Based on the setting of this header we would like to vary the cache and serve a different banner to the end user. How would you go about doing this? Keep in mind that we don't want to pollute the cache and we also don't want to create too many small cache segments. Assumptions: You can assume that the X-Carrier has already been detected in our cache. So, for the purposes of your test you can just set this value manually in your example script.

  Read the article

• Ubuntu and racadm

  - by lmqcn

  I recently purchased a used poweredge 1850 server and it came with a DRAC card. After wiping the HDD and installing ubuntu server 12.04.3 LTS amd64 on it, I am now trying to gain access to the DRAC which I believe is version 4. I have properly configured the DRAC to use it's own IP on my LAN and when I point my browser to the IP address, I am greeted with the DRAC login page (it has the dell logo and everything). However, after trying the credentials of root/calvin, I was denied access. So I think that the previous owners had set their own password. After doing some reading, it appears that I can reset the credentials to the default using racadm config -g cfgUserAdmin -o cfgUserAdminPassword -i 1 newpassword but upon entering the command, I get this error: bash: /usr/sbin/racadm: No such file or directory This holds true even if I run sudo su prior to running the racadm command. If, however, I run sudo racadm config -g cfgUserAdmin -o cfgUserAdminPassword -i 1 newpassword there are no errors. Yet, when I try to log into the DRAC via the web interface using the credentials of root/newpassword I am still not granted access. I installed the dell utilities via the guide at https://wiki.ubuntu.com/HardwareSupportMachinesServersDellNotes. I first tried to install the 64 bit version that is on the dell repositories, but after that was unsuccessful, I just followed the guide verbatim. No errors were produced in either case. I even followed the information at the bottom of the guide by executing sudo pppd /dev/ttyS1 1382400 crtscts noipdefault noauth lock persist connect 'chat -v "" CLIENT CLIENTSERVER "\\c"' but obviously, replacing the /dev/ttyS1 with the correct information for my system. ls -l /usr/sbin/ | grep racadm yields -rwxr-xr-x 1 root root 87930 Sep 16 04:03 racadm I have tried these credentials after each attempt of changing the password: root/calvin root/newpassword admin/calvin admin/newpassword All have been unsuccessful. What is the next course of action that I should take?

  Read the article

• Malaysian Airlines bans kids under 12, creates separate cabins in basement of flight

  - by Gopinath

  Kids are lot of fun to watch and play as long as they don’t start crying. Once they start crying it’s tough job for parents to calm them down and for people around it’s painful to be part of it. If it happens to be on a flight, it’s a biggest annoyance one can ever experience. Especially on long journey over night flights, it’s a nightmare for passengers if couple of kids are uncontrollable. After receiving many complaints from its passengers who are disturbed by kids in flight, Malaysian Airlines decided to ban kids under 12 in their regular Economy class cabins of new Airbus A380s. Parents with under 12 years old kids are allowed only in to special kids zone created in the basement of  the multi-storied jumbo flights Airbus A380s. May be parents with under 12 kids does not appreciate this move, but the rest of travellers would be happy. Back in June 2011 Malaysian Airlines banned infants in first class of its Boeing 747-400 jets. The CEO of Malaysian Airlines defended on twitter about the decision as first classers spend pricy amount for a comfortable journey.  So if you are a parent of kids  under 12, think twice before you book tickets on Malaysian Airlines. Creative commons image courtesy: flickr/transworld

  Read the article

• samba share not on network after upgrading to Ubuntu 12.04LTS.

  - by Sylvain Huard

  I just upgraded an old Ubuntu box to 12.04LTS (machine named A-Ubuntu). This is an upgrade not a format re-install. All the accounts and config were preserved. The basic setup is a local network with 2 Ubuntu machines (let say A-Ubuntu, B-Ubuntu) and a MAC (C-MAC). Before the upgrade, all of them could see each other by their names not only the IP address. The local network has a D-Link Router where everybody is connected with RJ-45 wired etherenet (not wi-fi). Since the A-Ubuntu upgrade, we can't see this machine name on the Network and its name is not on machine list in the D-Link router anymore. We can see it's IP address only. I can't access A-Ubuntu from the other two by its name but I can ping it with its address (192.168.0.109). From A-Ubuntu, I can connect and see the shared samba folders on B-Ubuntu and C-MAC. But from B-Ubuntu and C-MAc, I can't connect to A-Ubuntu. Correct me if I'm wrong but this tells me that Samba should be fine and the real problem is that A-Ubuntu does not advertise its name on the Network so the D-Link does not have it in its table so nobody else finds it. After a lot of googling, I see that it is the job of avahi and mdns to do so. Those packages are running, I checked multiple config files for samba, avahi, mdns to see as if it is like the examples on the WEB and also similar to what I find on the working B-Ubuntu machine. This is the same. I did multiple service restart with samba, avahi, remove the firewall to make sure it does not block the hostname broadcast. I rebooted multiple time to make sure the update I was making were effective. Still, Can't see the A-Ubuntu name on the network. Any idea what it can be?, Where to look next?

  Read the article

• can ping, but not SSH

  - by Matt

  So I have NetworkManager, connected to an AP on wlan1. I have wlan0 connected to a AdHoc network. I have Firestarter sharing my inet on the Adhoc. I have my ipod connected to wlan0, IP 10.42.43.101. wlan0 Link encap:Ethernet HWaddr ac:xx:12:81:7f:xx inet addr:10.42.43.1 Bcast:10.255.255.255 Mask:255.0.0.0 wlan1 Link encap:Ethernet HWaddr 00:xx:b3:98:f2:xx inet addr:10.0.1.61 Bcast:10.0.1.255 Mask:255.255.255.0 Now, I can ping my Jailbroken, SSH-enabled and running ipod touch: matt: ~ $ ping 10.42.43.101 PING 10.42.43.101 (10.42.43.101) 56(84) bytes of data. 64 bytes from 10.42.43.101: icmp_req=1 ttl=64 time=168 ms 64 bytes from 10.42.43.101: icmp_req=2 ttl=64 time=256 ms 64 bytes from 10.42.43.101: icmp_req=3 ttl=64 time=151 ms ^C --- 10.42.43.101 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1999ms rtt min/avg/max/mdev = 151.465/191.979/256.316/46.003 But I cannot SSH it: $ ssh [email protected] -vv OpenSSH_5.8p1 Debian-1ubuntu3, OpenSSL 0.9.8o 01 Jun 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 10.42.43.101 [10.42.43.101] port 22. It just stays there till I ^C it.. Here's my routing: $ ip route show 10.0.1.0/24 dev wlan1 proto kernel scope link src 10.0.1.61 metric 2 10.0.1.0/24 dev wlan1 proto kernel scope link src 10.0.1.61 metric 319 169.254.0.0/16 dev vboxnet0 proto kernel scope link src 169.254.128.223 metric 204 10.0.0.0/8 dev wlan0 proto kernel scope link src 10.42.43.1 default via 10.0.1.1 dev wlan1 proto static default via 10.0.1.1 dev wlan1 metric 319

  Read the article

• How do I access shared folders on Ubuntu server from Mac OS?

  - by Stephen

  I have an old dell desktop running ubuntu 11.04, I also have samba installed on it. I'm trying to access the shared folders on the Ubuntu machine from my Mac, so I go into 'Finder', click on 'Go' and 'Connect to Server'. I type in the ip address of the ubuntu machine smb://xxx.xxx.x.xx and click connect, I can then see the list of shared folders from the ubuntu machine so I know its making a connection. But when I access the 'Music' folder I get an error message stating: There was an error connecting to the server "xxx.xxx.x.xx". Check the server name or IP address, and try again. Any thoughts anyone ? EDIT I have a external hard drive attached to the server, and the folders I'm trying to access are located on that external hard drive. The location of the folder is /media/HD-CELU2/test, so I think the path from Finder should be smb://xxx.xxx.x.xx/media/HD-CELU2/test, but having tested this, I'm still not getting in. P.S. I'm using Samba as I have a Windows machine on my home network as well.

  Read the article

• Strange behavior on Gnome after update on from 13.04 to 13.10

  - by WayneBrady

  I made an automatic update on my Ubuntu 13.10 (from 13.04) system today. Since this point of time, I am in really big trouble. I use a VNC server with Gnome classic, after the update my Gnome was gone. So i tried everything. Checked the xstartup file of vncserver. Right now I reached a point where I can't find the answer. The logfile says that gnome-session-fallback is missing, even directly after I installed it with apt-get (tried it serveral times, installing, uninstalling and so on). I have no chance to use it as you can see in this terminal copy: root@ip-xxx:~/.vnc# apt-get install gnome-session-fallback Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed: gnome-session-fallback 0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded. Need to get 0 B/2,914 B of archives. After this operation, 247 kB of additional disk space will be used. Selecting previously unselected package gnome-session-fallback. (Reading database ... 210977 files and directories currently installed.) Unpacking gnome-session-fallback (from .../gnome-session-fallback_1%3a3.6.2-0ubuntu15_all.deb) ... Setting up gnome-session-fallback (1:3.6.2-0ubuntu15) ... root@ip-xxx:~/.vnc# gnome-session-fallback The program 'gnome-session-fallback' is currently not installed. You can install it by typing: apt-get install gnome-session-fallback If you have some idea, please give me a hint... Thank you!

  Read the article

• Add static ARP entries when network is brought up

  - by jozzas

  I have some pretty dumb IP devices on a subnet with my Ubuntu server, and the server receives streaming data from each device. I have run into a problem in that when an ARP request is issued to the device while it is streaming data to the server, the request is ignored, the cache entry times out and the server stops receiving the stream. So, to prevent the server from sending ARP requests to these devices altogether, I would like to add a static ARP entry for each, something like arp -i eth2 -s ip.of.the.device mac:of:the:device But these "static" ARP entries are lost if networking is disabled / enabled or if the server is rebooted. Where is the best place to automatically add these entries, preferably somewhere that will re-add them every time the interface eth2 is brought up? I really don't want to have to write a script that monitors the output of arp and re-adds the cache entries if they're missing. Edit to add what my final script was: Created the file /etc/network/if-up.d/add-my-static-arp With the contents: #!/bin/sh arp -i eth0 -s 192.168.0.4 00:50:cc:44:55:55 arp -i eth0 -s 192.168.0.5 00:50:cc:44:55:56 arp -i eth0 -s 192.168.0.6 00:50:cc:44:55:57 And then obviously add the permission to allow it to be executed: chmod +x /etc/network/if-up.d/add-my-static-arp And these arp entries will be manually added or re-added every time any network interface is brought up.

  Read the article

• Why do people crawl sites without downloading pictures?

  - by Michael

  Let me show you what I mean: IP Pages Hits Bandwidth 85.xx.xx.xxx 236 236 735.00 KB 195.xx.xxx.xx 164 164 533.74 KB 95.xxx.xxx.xxx 90 90 293.47 KB It's very clear that these person are crawling my site with bots. There's no way that you could visit my site and use <1MB bandwidth. You might say that there's the possibility that they could be browsing the site using some browser or plug-in that does not download images, js/css files, etc., but the simple fact of the matter is that there are not 90-236 pages that are linked from the home page (outside of WP files), even if you visited every page twice. I could understand if these people were crawling the site for pictures, but once again, the bandwidth indicates that this isn't what is happening. Why, then, would they crawl the site to simply view the HTML/txt/js/etc. files? The only thing that I can come up with is that they are scanning for outdated versions of WordPress, SQL injection vulnerabilities, etc., which makes me inclined to outright ban the IPs, but I'm curious, is it possible that this person is a legitimate user, or at the very least, not intending to be harmful?

  Read the article

• How to design a scriptable communication emulator?

  - by Hawk

  Requirement: We need a tool that simulates a hardware device that communicates via RS232 or TCP/IP to allow us to test our main application which will communicate with the device. Current flow: User loads script Parse script into commands User runs script Execute commands Script / commands (simplified for discussion): Connect RS232 = RS232ConnectCommand Connect TCP/IP = TcpIpConnectCommand Send data = SendCommand Receive data = ReceiveCommand Disconnect = DisconnectCommand All commands implement the ICommand interface. The command runner simply executes a sequence of ICommand implementations sequentially thus ICommand must have an Execute exposure, pseudo code: void Execute(ICommunicator context) The Execute method takes a context argument which allows the command implementations to execute what they need to do. For instance SendCommand will call context.Send, etc. The problem RS232ConnectCommand and TcpIpConnectCommand needs to instantiate the context to be used by subsequent commands. How do you handle this elegantly? Solution 1: Change ICommand Execute method to: ICommunicator Execute(ICommunicator context) While it will work it seems like a code smell. All commands now need to return the context which for all commands except the connection ones will be the same context that is passed in. Solution 2: Create an ICommunicatorWrapper (ICommunicationBroker?) which follows the decorator pattern and decorates ICommunicator. It introduces a new exposure: void SetCommunicator(ICommunicator communicator) And ICommand is changed to use the wrapper: void Execute(ICommunicationWrapper context) Seems like a cleaner solution. Question Is this a good design? Am I on the right track?

  Read the article

• Suddely internet is not accessible

  - by user189708

  I am going crazy here. One day everything was working fine. I turned pc off and went to sleep. Next day turn pc on and cannot access internet (from any browser). The situation is: I cannot open any webpage from browser (tried Firefox and Epiphany) and cannot receive emails in thunderbird. BUT if I run firefox from console as sudo, I can use it as usual. I can access Skype and pretty much any other network stuff (like installing software with apt-get etc.), also if I use Astrill VPN software I can access webpages even running without sudo. I haven't install any software or anything like that for several days = I have not a clue what could cause this. Just by the way, other Win PC in our home has no issue. Here is what I have tried to fix this: I have tried to restart my pc, router, modem - multiple times I have tried to change permissions to my firefox profile I have tried to completely re-install firefox and start with blank profile, thus no addons I have tried to change /etc/resolv.conf to an IP of my router (it was 127.0.1.1) I have tried to change my hostname (from tomino-NB to tominoNB) I think I might try even more stuff. None of it works. Can someone please try to help me. Thank you UPDATE 1: I have tried this: Removing resolv.conf - Didn't help Also "ping" and "dig" commands cannot resolve host UPDATE 2: I have tried to edit nameservers in resolv.conf but still no effect. I can ping router as well as I can ping outside IP. So definitely just some DNS issue. Is it possible that something is rewriting path to resolv.conf and using different file? UPDATE 3: I have just restarted PC and everything works now... resolv.conf went back to nameserver 127.0.1.1 . I have no clue what happened that it works again...

  Read the article

• Strange spam posts not making sense

  - by Paaland

  I'm running a web site with a forum where one small part is open for posting from unregistered users. The site uses captcha, but still some spam posts get through every day. Here is the thing. All of the messages follow the same pattern, but all also come from different IP's. That makes me thing this is some sort of automated scripted "attack" from a botnet of some sorts. The strange thing is that all the messages start with six random characters and contains a couple of links. The words have no meaning and the domains in the links does not even exist. Why would anyone use time and resources spreading these things? Below you can see two of these messages: A5Zfs6 exrzvrbspntz, [url=http://nktqoqllnuab.com/]nktqoqllnuab[/url], [link=http://wtrenldadvsy.com/]wtrenldadvsy[/link], [http://rnlrqfgdvdot.com/] O2oLpL nqeffxhryfdk, [url=http://jutyurbpfxow.com/]jutyurbpfxow[/url], [link=http://jpcdtmdalpow.com/]jpcdtmdalpow[/link], [http://qopqwqxwjdjx.com/] Since all the messages come from different IP's I can't see blocking those will help much. For now I'm considering just dropping all messages following this pattern since it's quite easy to match with a regexp. Have anyone else seen these kinds of messages or know the point of posting them?

  Read the article

• An adequate message authentication code for REST

  - by Andras Zoltan

  My REST service currently uses SCRAM authentication to issue tokens for callers and users. We have the ability to revoke caller privileges and ban IPs, as well as impose quotas to any type of request. One thing that I haven't implemented, however, is MAC for requests. As I've thought about it more, for some requests I think this is needed, because otherwise tokens can be stolen and before we identify this and deactivate the associated caller account, some damage could be done to our user accounts. In many systems the MAC is generated from the body or query string of the request, however this is difficult to implement as I'm using the ASP.Net Web API and don't want to read the body twice. Equally importantly I want to keep it simple for callers to access the service. So what I'm thinking is to have a MAC calculated on: the url, possibly minus query string the verb the request ip (potentially is a barrier on some mobile devices though) utc date and time when the client issues the request. For the last one I would have the client send that string in a request header, of course - and I can use it to decide whether the request is 'fresh' enough. My thinking is that whilst this doesn't prevent message body tampering it does prevent using a model request to use as a template for different requests later on by a malicious third party. I believe only the most aggressive man in the middle attack would be able to subvert this, and I don't think our services offer any information or ability that is valuable enough to warrant that. The services will use SSL as well, for sensitive stuff. And if I do this, then I'll be using HMAC-SHA-256 and issuing private keys for HMAC appropriately. Does this sound enough? Have I missed anything? I don't think I'm a beginner when it comes to security, but when working on it I always. am shrouded in doubt, so I appreciate having this community to call upon!

  Read the article

< Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >