Search Results

Search found 47660 results on 1907 pages for 'name resolution'.

Page 209/1907 | < Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >

• Acer aspire 5735z wireless not working after upgrade to 11.10

  - by Jon

  I cant get my wifi card to work at all after upgrading to 11.10 Oneiric. I'm not sure where to start to fix this. Ive tried using the additional drivers tool but this shows that no additional drivers are needed. Before my upgrade I had a drivers working for the Rt2860 chipset. Any help on this would be much appreciated.... thanks Jon jon@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1d:72:ec:76:d5 inet addr:192.168.1.134 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21d:72ff:feec:76d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7846 errors:0 dropped:0 overruns:0 frame:0 TX packets:7213 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8046624 (8.0 MB) TX bytes:1329442 (1.3 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:91 errors:0 dropped:0 overruns:0 frame:0 TX packets:91 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34497 (34.4 KB) TX bytes:34497 (34.4 KB) Ive included by dmesg output below [ 0.428818] NET: Registered protocol family 2 [ 0.429003] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.430562] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.436614] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.437409] TCP: Hash tables configured (established 524288 bind 65536) [ 0.437412] TCP reno registered [ 0.437431] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.437482] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.437678] NET: Registered protocol family 1 [ 0.437705] pci 0000:00:02.0: Boot video device [ 0.437892] PCI: CLS 64 bytes, default 64 [ 0.437916] Simple Boot Flag at 0x57 set to 0x1 [ 0.438294] audit: initializing netlink socket (disabled) [ 0.438309] type=2000 audit(1319243447.432:1): initialized [ 0.440763] Freeing initrd memory: 13416k freed [ 0.468362] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.488192] VFS: Disk quotas dquot_6.5.2 [ 0.488254] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.488888] fuse init (API version 7.16) [ 0.488985] msgmni has been set to 5890 [ 0.489381] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.489413] io scheduler noop registered [ 0.489415] io scheduler deadline registered [ 0.489460] io scheduler cfq registered (default) [ 0.489583] pcieport 0000:00:1c.0: setting latency timer to 64 [ 0.489633] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 0.489699] pcieport 0000:00:1c.1: setting latency timer to 64 [ 0.489741] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 0.489800] pcieport 0000:00:1c.2: setting latency timer to 64 [ 0.489841] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X [ 0.489904] pcieport 0000:00:1c.3: setting latency timer to 64 [ 0.489944] pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X [ 0.490006] pcieport 0000:00:1c.4: setting latency timer to 64 [ 0.490047] pcieport 0000:00:1c.4: irq 44 for MSI/MSI-X [ 0.490126] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.490149] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.490196] intel_idle: MWAIT substates: 0x1110 [ 0.490198] intel_idle: does not run on family 6 model 15 [ 0.491240] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.493473] ACPI: AC Adapter [ADP1] (on-line) [ 0.493590] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0 [ 0.496771] ACPI: Lid Switch [LID0] [ 0.496818] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 [ 0.496823] ACPI: Sleep Button [SLPB] [ 0.496865] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 [ 0.496869] ACPI: Power Button [PWRF] [ 0.496900] ACPI: acpi_idle registered with cpuidle [ 0.498719] Monitor-Mwait will be used to enter C-1 state [ 0.498753] Monitor-Mwait will be used to enter C-2 state [ 0.498761] Marking TSC unstable due to TSC halts in idle [ 0.517627] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.517630] ACPI: Thermal Zone [TZS0] (67 C) [ 0.524796] thermal LNXTHERM:01: registered as thermal_zone1 [ 0.524799] ACPI: Thermal Zone [TZS1] (67 C) [ 0.524823] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.524852] ERST: Table is not found! [ 0.524948] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.680991] ACPI: Battery Slot [BAT0] (battery present) [ 0.688567] Linux agpgart interface v0.103 [ 0.688672] agpgart-intel 0000:00:00.0: Intel GM45 Chipset [ 0.688865] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable [ 0.689786] agpgart-intel 0000:00:00.0: detected 65536K stolen memory [ 0.689912] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 [ 0.691006] brd: module loaded [ 0.691510] loop: module loaded [ 0.691967] Fixed MDIO Bus: probed [ 0.691990] PPP generic driver version 2.4.2 [ 0.692065] tun: Universal TUN/TAP device driver, 1.6 [ 0.692067] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 0.692146] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.692181] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 0.692206] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 0.692210] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 0.692255] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 0.692289] ehci_hcd 0000:00:1a.7: debug port 1 [ 0.696181] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported [ 0.696202] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xf8904800 [ 0.712014] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 0.712131] hub 1-0:1.0: USB hub found [ 0.712136] hub 1-0:1.0: 6 ports detected [ 0.712230] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.712243] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 0.712247] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 0.712287] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 0.712315] ehci_hcd 0000:00:1d.7: debug port 1 [ 0.716201] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 0.716216] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf8904c00 [ 0.732014] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 0.732130] hub 2-0:1.0: USB hub found [ 0.732135] hub 2-0:1.0: 6 ports detected [ 0.732209] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.732223] uhci_hcd: USB Universal Host Controller Interface driver [ 0.732254] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 0.732262] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 0.732265] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 0.732298] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 0.732325] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001820 [ 0.732441] hub 3-0:1.0: USB hub found [ 0.732445] hub 3-0:1.0: 2 ports detected [ 0.732508] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 20 (level, low) -> IRQ 20 [ 0.732514] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 0.732518] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 0.732553] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 0.732577] uhci_hcd 0000:00:1a.1: irq 20, io base 0x00001840 [ 0.732696] hub 4-0:1.0: USB hub found [ 0.732700] hub 4-0:1.0: 2 ports detected [ 0.732762] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 0.732768] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 0.732772] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 0.732805] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 0.732829] uhci_hcd 0000:00:1a.2: irq 20, io base 0x00001860 [ 0.732942] hub 5-0:1.0: USB hub found [ 0.732946] hub 5-0:1.0: 2 ports detected [ 0.733007] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.733014] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.733017] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.733057] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 0.733082] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001880 [ 0.733202] hub 6-0:1.0: USB hub found [ 0.733206] hub 6-0:1.0: 2 ports detected [ 0.733265] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.733273] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.733276] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.733313] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 0.733351] uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018a0 [ 0.733466] hub 7-0:1.0: USB hub found [ 0.733470] hub 7-0:1.0: 2 ports detected [ 0.733532] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.733539] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.733542] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.733578] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 0.733610] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018c0 [ 0.733730] hub 8-0:1.0: USB hub found [ 0.733736] hub 8-0:1.0: 2 ports detected [ 0.733843] i8042: PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 0.751594] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.751605] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.751732] mousedev: PS/2 mouse device common for all mice [ 0.752670] rtc_cmos 00:08: RTC can wake from S4 [ 0.752770] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 [ 0.752796] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 0.752907] device-mapper: uevent: version 1.0.3 [ 0.752976] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [email protected] [ 0.753028] cpuidle: using governor ladder [ 0.753093] cpuidle: using governor menu [ 0.753096] EFI Variables Facility v0.08 2004-May-17 [ 0.753361] TCP cubic registered [ 0.753482] NET: Registered protocol family 10 [ 0.753966] NET: Registered protocol family 17 [ 0.753992] Registering the dns_resolver key type [ 0.754113] PM: Hibernation image not present or could not be loaded. [ 0.754131] registered taskstats version 1 [ 0.771553] Magic number: 15:152:507 [ 0.771667] rtc_cmos 00:08: setting system clock to 2011-10-22 00:30:48 UTC (1319243448) [ 0.772238] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.772240] EDD information not available. [ 0.774165] Freeing unused kernel memory: 984k freed [ 0.774504] Write protecting the kernel read-only data: 10240k [ 0.774755] Freeing unused kernel memory: 20k freed [ 0.775093] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 [ 0.779727] Freeing unused kernel memory: 1400k freed [ 0.801946] udevd[84]: starting version 173 [ 0.880950] sky2: driver version 1.28 [ 0.881046] sky2 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.881096] sky2 0000:02:00.0: setting latency timer to 64 [ 0.881197] sky2 0000:02:00.0: Yukon-2 Extreme chip revision 2 [ 0.881871] sky2 0000:02:00.0: irq 45 for MSI/MSI-X [ 0.896273] sky2 0000:02:00.0: eth0: addr 00:1d:72:ec:76:d5 [ 0.910630] ahci 0000:00:1f.2: version 3.0 [ 0.910647] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.910710] ahci 0000:00:1f.2: irq 46 for MSI/MSI-X [ 0.910775] ahci: SSS flag set, parallel bus scan disabled [ 0.910812] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode [ 0.910816] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ccc ems sxs [ 0.910821] ahci 0000:00:1f.2: setting latency timer to 64 [ 0.941773] scsi0 : ahci [ 0.941954] scsi1 : ahci [ 0.942038] scsi2 : ahci [ 0.942118] scsi3 : ahci [ 0.942196] scsi4 : ahci [ 0.942268] scsi5 : ahci [ 0.942332] ata1: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904100 irq 46 [ 0.942336] ata2: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904180 irq 46 [ 0.942339] ata3: DUMMY [ 0.942340] ata4: DUMMY [ 0.942344] ata5: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904300 irq 46 [ 0.942347] ata6: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904380 irq 46 [ 1.028061] usb 1-5: new high speed USB device number 2 using ehci_hcd [ 1.181775] usbcore: registered new interface driver uas [ 1.260062] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.261126] ata1.00: ATA-8: Hitachi HTS543225L9A300, FBEOC40C, max UDMA/133 [ 1.261129] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 1.262360] ata1.00: configured for UDMA/133 [ 1.262518] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54322 FBEO PQ: 0 ANSI: 5 [ 1.262716] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.262762] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB) [ 1.262824] sd 0:0:0:0: [sda] Write Protect is off [ 1.262827] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.262851] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.287277] sda: sda1 sda2 sda3 [ 1.287693] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.580059] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.581188] ata2.00: ATAPI: HL-DT-STDVDRAM GT10N, 1.00, max UDMA/100 [ 1.582663] ata2.00: configured for UDMA/100 [ 1.584162] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GT10N 1.00 PQ: 0 ANSI: 5 [ 1.585821] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.585824] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.585953] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 1.586038] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 1.632061] usb 6-1: new low speed USB device number 2 using uhci_hcd [ 1.908056] ata5: SATA link down (SStatus 0 SControl 300) [ 2.228065] ata6: SATA link down (SStatus 0 SControl 300) [ 2.228955] Initializing USB Mass Storage driver... [ 2.229052] usbcore: registered new interface driver usb-storage [ 2.229054] USB Mass Storage support registered. [ 2.235827] scsi6 : usb-storage 1-5:1.0 [ 2.235987] usbcore: registered new interface driver ums-realtek [ 2.244451] input: B16_b_02 USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/input/input4 [ 2.244598] generic-usb 0003:046D:C025.0001: input,hidraw0: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-1/input0 [ 2.244620] usbcore: registered new interface driver usbhid [ 2.244622] usbhid: USB HID core driver [ 3.091083] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null) [ 3.238275] scsi 6:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS [ 3.348261] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 3.351897] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 47.138012] udevd[334]: starting version 173 [ 47.177678] lp: driver loaded but no devices found [ 47.197084] wmi: Mapper loaded [ 47.197526] acer_wmi: Acer Laptop ACPI-WMI Extras [ 47.210227] acer_wmi: Brightness must be controlled by generic video driver [ 47.566578] Disabling lock debugging due to kernel taint [ 47.584050] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 47.620666] type=1400 audit(1319239895.347:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=624 comm="apparmor_parser" [ 47.620934] type=1400 audit(1319239895.347:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=624 comm="apparmor_parser" [ 47.621108] type=1400 audit(1319239895.347:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=624 comm="apparmor_parser" [ 47.633056] [drm] Initialized drm 1.1.0 20060810 [ 47.722594] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 47.722602] i915 0000:00:02.0: setting latency timer to 64 [ 47.807152] ndiswrapper (check_nt_hdr:141): kernel is 64-bit, but Windows driver is not 64-bit;bad magic: 010B [ 47.807159] ndiswrapper (load_sys_files:206): couldn't prepare driver 'rt2860' [ 47.807930] ndiswrapper (load_wrap_driver:108): couldn't load driver rt2860; check system log for messages from 'loadndisdriver' [ 47.856250] usbcore: registered new interface driver ndiswrapper [ 47.861772] i915 0000:00:02.0: irq 47 for MSI/MSI-X [ 47.861781] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 47.861783] [drm] Driver supports precise vblank timestamp query. [ 47.861842] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 47.980620] fixme: max PWM is zero. [ 48.286153] fbcon: inteldrmfb (fb0) is primary device [ 48.287033] Console: switching to colour frame buffer device 170x48 [ 48.287062] fb0: inteldrmfb frame buffer device [ 48.287064] drm: registered panic notifier [ 48.333883] acpi device:02: registered as cooling_device2 [ 48.334053] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 48.334128] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 48.334203] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 48.334644] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0 [ 48.334652] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0 [ 48.334673] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 48.334737] HDA Intel 0000:00:1b.0: irq 48 for MSI/MSI-X [ 48.334772] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 48.356107] Adding 261116k swap on /host/ubuntu/disks/swap.disk. Priority:-1 extents:1 across:261116k [ 48.380946] hda_codec: ALC268: BIOS auto-probing. [ 48.390242] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6 [ 48.390365] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [ 48.490870] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,user_xattr [ 48.917990] ppdev: user-space parallel port driver [ 48.950729] type=1400 audit(1319239896.675:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=941 comm="apparmor_parser" [ 48.951114] type=1400 audit(1319239896.675:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=941 comm="apparmor_parser" [ 48.977706] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa44000/0xa0000 [ 49.048871] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8 [ 49.078713] sky2 0000:02:00.0: eth0: enabling interface [ 49.079462] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 50.762266] sky2 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control rx [ 50.762702] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 54.751478] type=1400 audit(1319239902.475:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session-wrapper" pid=1039 comm="apparmor_parser" [ 54.755907] type=1400 audit(1319239902.479:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1040 comm="apparmor_parser" [ 54.756237] type=1400 audit(1319239902.483:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1040 comm="apparmor_parser" [ 54.756417] type=1400 audit(1319239902.483:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1040 comm="apparmor_parser" [ 54.764825] type=1400 audit(1319239902.491:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=1041 comm="apparmor_parser" [ 54.768365] type=1400 audit(1319239902.495:12): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=1041 comm="apparmor_parser" [ 54.770601] type=1400 audit(1319239902.495:13): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=1041 comm="apparmor_parser" [ 54.770729] type=1400 audit(1319239902.495:14): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=1038 comm="apparmor_parser" [ 54.775181] type=1400 audit(1319239902.499:15): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1043 comm="apparmor_parser" [ 54.775533] type=1400 audit(1319239902.499:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1043 comm="apparmor_parser" [ 54.936691] init: failsafe main process (891) killed by TERM signal [ 54.944583] init: apport pre-start process (1096) terminated with status 1 [ 55.000373] init: apport post-stop process (1160) terminated with status 1 [ 55.005291] init: gdm main process (1159) killed by TERM signal [ 59.782579] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 [ 60.992021] eth0: no IPv6 routers present [ 61.936072] device eth0 entered promiscuous mode [ 62.053949] Bluetooth: Core ver 2.16 [ 62.054005] NET: Registered protocol family 31 [ 62.054007] Bluetooth: HCI device and connection manager initialized [ 62.054010] Bluetooth: HCI socket layer initialized [ 62.054012] Bluetooth: L2CAP socket layer initialized [ 62.054993] Bluetooth: SCO socket layer initialized [ 62.058750] Bluetooth: RFCOMM TTY layer initialized [ 62.058758] Bluetooth: RFCOMM socket layer initialized [ 62.058760] Bluetooth: RFCOMM ver 1.11 [ 62.059428] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 62.059432] Bluetooth: BNEP filters: protocol multicast [ 62.460389] init: plymouth-stop pre-start process (1662) terminated with status 1 '

  Read the article

• Simple GET operation with JSON data in ADF Mobile

  - by PadmajaBhat

  Usecase: This sample uses a RESTful service which contains a GET method that fetches employee details for an employee with given employee ID along with other methods. The data is fetched in JSON format. This RESTful service is then invoked via ADF Mobile and the JSON data thus obtained is parsed and rendered in mobile in a table. Prerequisite: Download JDev build JDEVADF_11.1.2.4.0_GENERIC_130421.1600.6436.1 or higher with mobile support.  Steps: Run EmployeeService.java in JSONService.zip. This is a simple service with a method, getEmpById(id) that takes employee ID as parameter and produces employee details in JSON format. Copy the target URL generated on running this service. The target URL will be as shown below: http://127.0.0.1:7101/JSONService-Project1-context-root/jersey/project1 Now, let us invoke this service in our mobile application. For this, create an ADF Mobile application.  Name the application JSON_SearchByEmpID and finish the wizard. Now, let us create a connection to our service. To do this, we create a URL Connection. Invoke new gallery wizard on ApplicationController project.  Select URL Connection option. In the Create URL Connection window, enter connection name as ‘conn’. For URL endpoint, supply the URL you copied earlier on running the service. Remember to use your system IP instead of localhost. Test the connection and click OK. At this point, a connection to the REST service has been created. Since JSON data is not supported directly in WSDC wizard, we need to invoke the operation through Java code using RestServiceAdapter. For this, in the ApplicationController project, create a Java class called ‘EmployeeDC’. We will be creating DC from this class. Add the following code to the newly created class to invoke the getEmpById method. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 public Employee fetchEmpDetails(){ RestServiceAdapter restServiceAdapter = Model.createRestServiceAdapter(); restServiceAdapter.clearRequestProperties(); restServiceAdapter.setConnectionName("conn"); //URL connection created with this name restServiceAdapter.setRequestType(RestServiceAdapter.REQUEST_TYPE_GET); restServiceAdapter.addRequestProperty("Content-Type", "application/json"); restServiceAdapter.addRequestProperty("Accept", "application/json; charset=UTF-8"); restServiceAdapter.setRetryLimit(0); restServiceAdapter.setRequestURI("/getById/"+inputEmpID); String response = ""; JSONBeanSerializationHelper jsonHelper = new JSONBeanSerializationHelper(); try { response = restServiceAdapter.send(""); //Invoke the GET operation System.out.println("Response received!"); Employee responseObject = (Employee) jsonHelper.fromJSON(Employee.class, response); return responseObject; } catch (Exception e) { } return null; } Here, in lines 2 to 9, we create the RestServiceAdapter and set various properties required to invoke the web service. At line 4, we are pointing to the connection ‘conn’ created previously. Since we want to invoke getEmpById method of the service, which is defined by the URL http://IP:7101/REST_Sanity_JSON-Project1-context-root/resources/project1/getById/{id} we are updating the request URI to point to this URI at line 9. inputEmpID is a variable that will hold the value input by the user for employee ID. This we will be creating in a while. As the method we are invoking is a GET operation and consumes json data, these properties are being set in lines 5 through 7. Finally, we are sending the request in line 13. In line 15, we use jsonHelper.fromJSON to convert received JSON data to a Java object. The required Java objects' structure is defined in class Employee.java whose structure is provided later. Since the response from our service is a simple response consisting of attributes like employee Id, name, design etc, we will just return this parsed response (line 16) and use it to create DC. As mentioned previously, we would like the user to input the employee ID for which he/she wants to perform search. So, in the same class, define a variable inputEmpID which will hold the value input by the user. Generate accessors for this variable. Lastly, we need to create Employee class. Employee class will define how we want to structure the JSON object received from the service. To design the Employee class, run the services’ method in the browser or via analyzer using path parameter as 1. This will give you the output JSON structure. Ours is a simple service that returns a JSONObject with a set of data. Hence, Employee class will just contain this set of data defined with the proper data types. Create Employee.java in the same project as EmployeeDC.java and write the below code: package application; import oracle.adfmf.java.beans.PropertyChangeListener; import oracle.adfmf.java.beans.PropertyChangeSupport; public class Employee { private String dept; private String desig; private int id; private String name; private int salary; private PropertyChangeSupport propertyChangeSupport = new PropertyChangeSupport(this); public void setDept(String dept) {         String oldDept = this.dept; this.dept = dept; propertyChangeSupport.firePropertyChange("dept", oldDept, dept); } public String getDept() { return dept; } public void setDesig(String desig) { String oldDesig = this.desig; this.desig = desig; propertyChangeSupport.firePropertyChange("desig", oldDesig, desig); } public String getDesig() { return desig; } public void setId(int id) { int oldId = this.id; this.id = id; propertyChangeSupport.firePropertyChange("id", oldId, id); } public int getId() { return id; } public void setName(String name) { String oldName = this.name; this.name = name; propertyChangeSupport.firePropertyChange("name", oldName, name); } public String getName() { return name; } public void setSalary(int salary) { int oldSalary = this.salary; this.salary = salary; propertyChangeSupport.firePropertyChange("salary", oldSalary, salary); } public int getSalary() { return salary; } public void addPropertyChangeListener(PropertyChangeListener l) { propertyChangeSupport.addPropertyChangeListener(l); } public void removePropertyChangeListener(PropertyChangeListener l) { propertyChangeSupport.removePropertyChangeListener(l);     } } Now, let us create a DC out of EmployeeDC.java.  DC as shown below is created. Now, you can design the mobile page as usual and invoke the operation of the service. To design the page, go to ViewController project and locate adfmf-feature.xml. Create a new feature called ‘SearchFeature’ by clicking the plus icon. Go the content tab and add an amx page. Call it SearchPage.amx. Call it SearchPage.amx. Remove primary and secondary buttons as we don’t need them and rename the header. Drag and drop inputEmpID from the DC palette onto Panel Page in the structure pane as input text with label. Next, drop fetchEmpDetails method as an ADF button. For a change, let us display the output in a table component instead of the usual form. However, you will notice that if you drag and drop Employee onto the structure pane, there is no option for ADF Mobile Table. Hence, we will need to create the table on our own. To do this, let us first drop Employee as an ADF Read -Only form. This step is needed to get the required bindings. We will be deleting this form in a while. Now, from the Component palette, search for ‘Table Layout’. Drag and drop this below the command button.  Within the tablelayout, insert ‘Row Layout’ and ‘Cell Format’ components. Final table structure should be as shown below. Here, we have also defined some inline styling to render the UI in a nice manner. <amx:tableLayout id="tl1" borderWidth="2" halign="center" inlineStyle="vertical-align:middle;" width="100%" cellPadding="10"> <amx:rowLayout id="rl1" > <amx:cellFormat id="cf1" width="30%"> <amx:outputText value="#{bindings.dept.hints.label}" id="ot7" inlineStyle="color:rgb(0,148,231);"/> </amx:cellFormat> <amx:cellFormat id="cf2"> <amx:outputText value="#{bindings.dept.inputValue}" id="ot8" /> </amx:cellFormat> </amx:rowLayout> <amx:rowLayout id="rl2"> <amx:cellFormat id="cf3" width="30%"> <amx:outputText value="#{bindings.desig.hints.label}" id="ot9" inlineStyle="color:rgb(0,148,231);"/> </amx:cellFormat> <amx:cellFormat id="cf4" > <amx:outputText value="#{bindings.desig.inputValue}" id="ot10"/> </amx:cellFormat> </amx:rowLayout> <amx:rowLayout id="rl3"> <amx:cellFormat id="cf5" width="30%"> <amx:outputText value="#{bindings.id.hints.label}" id="ot11" inlineStyle="color:rgb(0,148,231);"/> </amx:cellFormat> <amx:cellFormat id="cf6" > <amx:outputText value="#{bindings.id.inputValue}" id="ot12"/> </amx:cellFormat> </amx:rowLayout> <amx:rowLayout id="rl4"> <amx:cellFormat id="cf7" width="30%"> <amx:outputText value="#{bindings.name.hints.label}" id="ot13" inlineStyle="color:rgb(0,148,231);"/> </amx:cellFormat> <amx:cellFormat id="cf8"> <amx:outputText value="#{bindings.name.inputValue}" id="ot14"/> </amx:cellFormat> </amx:rowLayout> <amx:rowLayout id="rl5"> <amx:cellFormat id="cf9" width="30%"> <amx:outputText value="#{bindings.salary.hints.label}" id="ot15" inlineStyle="color:rgb(0,148,231);"/> </amx:cellFormat> <amx:cellFormat id="cf10"> <amx:outputText value="#{bindings.salary.inputValue}" id="ot16"/> </amx:cellFormat> </amx:rowLayout>     </amx:tableLayout> The values used in the output text of the table come from the bindings obtained from the ADF Form created earlier. As we have used the bindings and don’t need the form anymore, let us delete the form.  One last thing before we deploy. When user changes employee ID, we want to clear the table contents. For this we associate a value change listener with the input text box. Click New in the resulting dialog to create a managed bean. Next, we create a method within the managed bean. For this, click on the New button associated with method. Call the method ‘empIDChange’. Open myClass.java and write the below code in empIDChange(). public void empIDChange(ValueChangeEvent valueChangeEvent) { // Add event code here... //Resetting the values to blank values when employee id changes AdfELContext adfELContext = AdfmfJavaUtilities.getAdfELContext(); ValueExpression ve = AdfmfJavaUtilities.getValueExpression("#{bindings.dept.inputValue}", String.class); ve.setValue(adfELContext, ""); ve = AdfmfJavaUtilities.getValueExpression("#{bindings.desig.inputValue}", String.class); ve.setValue(adfELContext, ""); ve = AdfmfJavaUtilities.getValueExpression("#{bindings.id.inputValue}", int.class); ve.setValue(adfELContext, ""); ve = AdfmfJavaUtilities.getValueExpression("#{bindings.name.inputValue}", String.class); ve.setValue(adfELContext, ""); ve = AdfmfJavaUtilities.getValueExpression("#{bindings.salary.inputValue}", int.class); ve.setValue(adfELContext, ""); } That’s it. Deploy the application to android emulator or device. Some snippets from the app.

  Read the article

• HttpClient POST fails to submit the form

  - by Jayomat

  Hi, I'm writing an app to check for the bus timetable's. Therefor I need to post some data to a html page, submit it, and parse the resulting page with htmlparser. Though it may be asked a lot, can some one help me identify if 1) this page does support post/get (I think it does) 2) which fields I need to use? 3) How to make the actual request? this is my code so far: String url = "http://busspur02.aseag.de/bs.exe?Cmd=RV&Karten=true&DatumT=30&DatumM=4&DatumJ=2010&ZeitH=&ZeitM=&Suchen=%28S%29uchen&GT0=&HT0=&GT1=&HT1="; String charset = "CP1252"; System.out.println("startFrom: "+start_from); System.out.println("goTo: "+destination); //String tag.v List<NameValuePair> params = new ArrayList<NameValuePair>(); params.add(new BasicNameValuePair("HTO", start_from)); params.add(new BasicNameValuePair("HT1", destination)); params.add(new BasicNameValuePair("GTO", "Aachen")); params.add(new BasicNameValuePair("GT1", "Aachen")); params.add(new BasicNameValuePair("DatumT", day)); params.add(new BasicNameValuePair("DatumM", month)); params.add(new BasicNameValuePair("DatumJ", year)); params.add(new BasicNameValuePair("ZeitH", hour)); params.add(new BasicNameValuePair("ZeitM", min)); UrlEncodedFormEntity query = new UrlEncodedFormEntity(params, charset); HttpPost post = new HttpPost(url); post.setEntity(query); InputStream response = new DefaultHttpClient().execute(post).getEntity().getContent(); // Now do your thing with the facebook response. String source = readText(response,"CP1252"); Log.d(TAG_AVV,response.toString()); System.out.println("STREAM "+source); One person also gave me a hint to use firebug to read what's going on at the page, but I don't really understand what to look for, or more precisely, how to use the provided information. I also find it confusing, for example, that when I enter the data by hand, the url says, for example, "....HTO=Kaiserplatz&...", but in Firebug, the same Kaiserplatz is connected to a different field, in this case: \<\td class="Start3" Kaiserplatz <\/td (I inserted \ to make it visible) The last line in my code prints the html page, but without having send a request.. it's printed as if there was no input at all... My app is almost done, I hope someone can help me out to finish it! thanks in advance EDIT: this is what the s.o.p returns: (At some point there actually is some input, but only the destination ???) 04-30 03:15:43.524: INFO/System.out(3303): STREAM <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> 04-30 03:15:43.524: INFO/System.out(3303): <html> 04-30 03:15:43.524: INFO/System.out(3303): <head> 04-30 03:15:43.545: INFO/System.out(3303): <title>Busspur online</title> 04-30 03:15:43.554: INFO/System.out(3303): <base href="http://busspur02.aseag.de"> 04-30 03:15:43.554: INFO/System.out(3303): <meta name="description" content="Busspur im Internet"> 04-30 03:15:43.554: INFO/System.out(3303): <meta name="author" content="Dr. Manfred Enning"> 04-30 03:15:43.554: INFO/System.out(3303): <meta name="AUTH_TYPE" content="Basic"> 04-30 03:15:43.574: INFO/System.out(3303): <meta HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=windows-1252"> 04-30 03:15:43.574: INFO/System.out(3303): <meta HTTP-EQUIV="Content-Language" CONTENT="de"> 04-30 03:15:43.574: INFO/System.out(3303): <link rel=stylesheet type="text/css" href="busspur.css"> 04-30 03:15:43.574: INFO/System.out(3303): </head> 04-30 03:15:43.574: INFO/System.out(3303): 04-30 03:15:43.574: INFO/System.out(3303): <body> 04-30 03:15:43.574: INFO/System.out(3303): <table border="0" cellspacing="0" cellpadding="0" width="100%"> 04-30 03:15:43.574: INFO/System.out(3303): <tr> 04-30 03:15:43.584: INFO/System.out(3303): <td align="left" width="25%"><small>Version: 6.8.1.9s2<br>Datenstand: 13.04.2010 04-30 03:15:43.584: INFO/System.out(3303): 04-30 03:15:43.584: INFO/System.out(3303): <br>12.04.2010 - 12.06.2010 04-30 03:15:43.584: INFO/System.out(3303): <br>1663 04-30 03:15:43.584: INFO/System.out(3303): 3D3B9</small> 04-30 03:15:43.584: INFO/System.out(3303): </td> 04-30 03:15:43.584: INFO/System.out(3303): 04-30 03:15:43.584: INFO/System.out(3303): <td align="center" width="50%"> 04-30 03:15:43.584: INFO/System.out(3303): <a href="/bs.exe/SL?Sprache=Nederlands&amp;SID=3D3B9"><img src="http://www.busspur.de/logos/nederlands.gif" alt="Nederlands" border="0" Width="32" Height="22"></a><a href="/bs.exe/SL?Sprache=English&amp;SID=3D3B9"><img src="http://www.busspur.de/logos/english.gif" alt="English" border="0" Width="32" Height="22"></a><a href="/bs.exe/SL?Sprache=Francais&amp;SID=3D3B9"><img src="http://www.busspur.de/logos/francais.gif" alt="Francais" border="0" Width="32" Height="22"></a> 04-30 03:15:43.584: INFO/System.out(3303): </td> 04-30 03:15:43.584: INFO/System.out(3303): 04-30 03:15:43.594: INFO/System.out(3303): <td align="right" width="25%"> 04-30 03:15:43.594: INFO/System.out(3303): <a href="http://www.avv.de/"><img src="/logos/avvlogo.gif" border="0" alt="AVV"></a> 04-30 03:15:43.594: INFO/System.out(3303): </td> 04-30 03:15:43.594: INFO/System.out(3303): </tr> 04-30 03:15:43.594: INFO/System.out(3303): </table> 04-30 03:15:43.594: INFO/System.out(3303): 04-30 03:15:43.594: INFO/System.out(3303): <!-- Kopfbereich (automatisch erzeugt) --> 04-30 03:15:43.594: INFO/System.out(3303): <div align="center"> 04-30 03:15:43.594: INFO/System.out(3303): 04-30 03:15:43.604: INFO/System.out(3303): <H2>Busspur-Online <i>Verbindungsabfrage</i></H2> 04-30 03:15:43.604: INFO/System.out(3303): </div> 04-30 03:15:43.604: INFO/System.out(3303): <!-- Ende Kopfbereich --> 04-30 03:15:43.604: INFO/System.out(3303): 04-30 03:15:43.604: INFO/System.out(3303): <!-- Ausgabebereich (automatisch erzeugt) --> 04-30 03:15:43.604: INFO/System.out(3303): <div align="center"> 04-30 03:15:43.614: INFO/System.out(3303): <p></p> 04-30 03:15:43.614: INFO/System.out(3303): <p></p> 04-30 03:15:43.614: INFO/System.out(3303): 04-30 03:15:43.614: INFO/System.out(3303): 04-30 03:15:43.624: INFO/System.out(3303): </div> 04-30 03:15:43.624: INFO/System.out(3303): <!-- Ende Ausgabebereich --> 04-30 03:15:43.634: INFO/System.out(3303): 04-30 03:15:43.634: INFO/System.out(3303): <!-- Fussnotenbereich (automatisch erzeugt) --> 04-30 03:15:43.634: INFO/System.out(3303): <div align="left"> 04-30 03:15:43.634: INFO/System.out(3303): 04-30 03:15:43.634: INFO/System.out(3303): 04-30 03:15:43.634: INFO/System.out(3303): </div> 04-30 03:15:43.634: INFO/System.out(3303): <!-- Ende Fussnotenbereich --> 04-30 03:15:43.634: INFO/System.out(3303): 04-30 03:15:43.634: INFO/System.out(3303): <!-- Nachschlageliste (automatisch erzeugt) --> 04-30 03:15:43.634: INFO/System.out(3303): <div align="center"> 04-30 03:15:43.644: INFO/System.out(3303): 04-30 03:15:43.644: INFO/System.out(3303): </div> 04-30 03:15:43.644: INFO/System.out(3303): <!-- Ende Nachschlageliste --> 04-30 03:15:43.644: INFO/System.out(3303): 04-30 03:15:43.644: INFO/System.out(3303): 04-30 03:15:43.644: INFO/System.out(3303): <!-- Eingabeformular --> 04-30 03:15:43.644: INFO/System.out(3303): 04-30 03:15:43.644: INFO/System.out(3303): 04-30 03:15:43.644: INFO/System.out(3303): <!-- Eingabeformular --> 04-30 03:15:43.644: INFO/System.out(3303): <form name="Maske" action="/bs.exe" method="get"> 04-30 03:15:43.644: INFO/System.out(3303): 04-30 03:15:43.644: INFO/System.out(3303): <input type="hidden" name="SID" value="3D3B9"> 04-30 03:15:43.644: INFO/System.out(3303): <input type="hidden" name="ScreenX" value=""> 04-30 03:15:43.654: INFO/System.out(3303): <input type="hidden" name="ScreenY" value=""> 04-30 03:15:43.654: INFO/System.out(3303): <input type="hidden" class="hiddenForm" name="CMD" value="CR" /> 04-30 03:15:43.654: INFO/System.out(3303): 04-30 03:15:43.654: INFO/System.out(3303): 04-30 03:15:43.654: INFO/System.out(3303): <input TYPE="Submit" name="Suchen" value="S" tabindex="20" style="visibility:hidden"> 04-30 03:15:43.654: INFO/System.out(3303): 04-30 03:15:43.654: INFO/System.out(3303): <table align="center" border="0" cellspacing="0" cellpadding="2"> 04-30 03:15:43.654: INFO/System.out(3303): <tr> 04-30 03:15:43.654: INFO/System.out(3303): <td class="Haupt"> 04-30 03:15:43.654: INFO/System.out(3303): 04-30 03:15:43.674: INFO/System.out(3303): <table border="0" cellspacing="0" cellpadding="2"> 04-30 03:15:43.674: INFO/System.out(3303): <!-- 1.Zeile Startauswahl --> 04-30 03:15:43.674: INFO/System.out(3303): <tr> 04-30 03:15:43.674: INFO/System.out(3303): <td rowspan="2" class="Start1"> 04-30 03:15:43.674: INFO/System.out(3303): Start 04-30 03:15:43.685: INFO/System.out(3303): </td> 04-30 03:15:43.685: INFO/System.out(3303): 04-30 03:15:43.685: INFO/System.out(3303): <td class="Start2" height="25"> 04-30 03:15:43.685: INFO/System.out(3303): Stadt/Gemeinde 04-30 03:15:43.685: INFO/System.out(3303): </td> 04-30 03:15:43.685: INFO/System.out(3303): 04-30 03:15:43.685: INFO/System.out(3303): <td class="Start3"> 04-30 03:15:43.685: INFO/System.out(3303): <input type="text" name="GT0" value="" tabindex="1" /> 04-30 03:15:43.704: INFO/System.out(3303): 04-30 03:15:43.704: INFO/System.out(3303): </td> 04-30 03:15:43.704: INFO/System.out(3303): 04-30 03:15:43.704: INFO/System.out(3303): 04-30 03:15:43.704: INFO/System.out(3303): <td rowspan="2" class="Start4"> 04-30 03:15:43.714: INFO/System.out(3303): <input type="submit" name="Map0" value="Karte" tabindex="100" /> 04-30 03:15:43.724: INFO/System.out(3303): 04-30 03:15:43.724: INFO/System.out(3303): </td> 04-30 03:15:43.724: INFO/System.out(3303): 04-30 03:15:43.724: INFO/System.out(3303): 04-30 03:15:43.724: INFO/System.out(3303): </tr> 04-30 03:15:43.724: INFO/System.out(3303): 04-30 03:15:43.724: INFO/System.out(3303): <tr> 04-30 03:15:43.734: INFO/System.out(3303): <td class="Start2" height="25"> 04-30 03:15:43.734: INFO/System.out(3303): <select name="T0" id="efaT0"> 04-30 03:15:43.734: INFO/System.out(3303): <option value="A" >Adresse 04-30 03:15:43.734: INFO/System.out(3303): <option value="H" selected="selected">Haltestelle 04-30 03:15:43.734: INFO/System.out(3303): <option value="Z" >Bes. Ziel 04-30 03:15:43.734: INFO/System.out(3303): </select> 04-30 03:15:43.734: INFO/System.out(3303): 04-30 03:15:43.734: INFO/System.out(3303): </td> 04-30 03:15:43.734: INFO/System.out(3303): 04-30 03:15:43.734: INFO/System.out(3303): <td class="Start3"> 04-30 03:15:43.734: INFO/System.out(3303): <input type="text" name="HT0" value="" tabindex="2" /> 04-30 03:15:43.734: INFO/System.out(3303): 04-30 03:15:43.745: INFO/System.out(3303): </td> 04-30 03:15:43.754: INFO/System.out(3303): 04-30 03:15:43.774: INFO/System.out(3303): </tr> 04-30 03:15:43.784: INFO/System.out(3303): 04-30 03:15:43.784: INFO/System.out(3303): <!-- 2.Zeile Ziel oder ViaAuswahl --> 04-30 03:15:43.784: INFO/System.out(3303): 04-30 03:15:43.805: INFO/System.out(3303): <tr> 04-30 03:15:43.834: INFO/System.out(3303): <td rowspan="2" class="Ziel1"> 04-30 03:15:43.834: INFO/System.out(3303): Ziel 04-30 03:15:43.834: INFO/System.out(3303): </td> 04-30 03:15:43.844: INFO/System.out(3303): 04-30 03:15:43.844: INFO/System.out(3303): <td class="Ziel2" height="25"> 04-30 03:15:43.844: INFO/System.out(3303): Stadt/Gemeinde 04-30 03:15:43.844: INFO/System.out(3303): </td> 04-30 03:15:43.854: INFO/System.out(3303): 04-30 03:15:43.854: INFO/System.out(3303): <td class="Ziel3"> 04-30 03:15:43.854: INFO/System.out(3303): Aachen 04-30 03:15:43.864: INFO/System.out(3303): </td> 04-30 03:15:43.874: INFO/System.out(3303): 04-30 03:15:43.874: INFO/System.out(3303): 04-30 03:15:43.884: INFO/System.out(3303): <td rowspan="2" class="Ziel4"> 04-30 03:15:43.884: INFO/System.out(3303): <input type="submit" name="Map1" value="Karte" tabindex="101" /> 04-30 03:15:43.884: INFO/System.out(3303): 04-30 03:15:43.884: INFO/System.out(3303): </td> 04-30 03:15:43.884: INFO/System.out(3303): 04-30 03:15:43.884: INFO/System.out(3303): 04-30 03:15:43.884: INFO/System.out(3303): </tr> 04-30 03:15:43.884: INFO/System.out(3303): 04-30 03:15:43.884: INFO/System.out(3303): <tr> 04-30 03:15:43.884: INFO/System.out(3303): <td class="Ziel2" height="25"> 04-30 03:15:43.894: INFO/System.out(3303): <small></small> 04-30 03:15:43.894: INFO/System.out(3303): </td> 04-30 03:15:43.894: INFO/System.out(3303): <td class="Ziel3"> 04-30 03:15:43.894: INFO/System.out(3303): Karlsgraben 04-30 03:15:43.904: INFO/System.out(3303): </td> 04-30 03:15:43.904: INFO/System.out(3303): </tr> 04-30 03:15:43.904: INFO/System.out(3303): 04-30 03:15:43.914: INFO/System.out(3303): 04-30 03:15:43.924: INFO/System.out(3303): 04-30 03:15:43.934: INFO/System.out(3303): 04-30 03:15:43.934: INFO/System.out(3303): 04-30 03:15:43.934: INFO/System.out(3303): 04-30 03:15:43.934: INFO/System.out(3303): <!-- 3.Zeile Datum/Zeit/Intervall --> 04-30 03:15:43.934: INFO/System.out(3303): <tr> 04-30 03:15:43.944: INFO/System.out(3303): <td rowspan="3" class="Zeit1"> 04-30 03:15:43.944: INFO/System.out(3303): Zeit 04-30 03:15:43.944: INFO/System.out(3303): </td> 04-30 03:15:43.944: INFO/System.out(3303): <td class="Datum2"> 04-30 03:15:43.944: INFO/System.out(3303): Datum 04-30 03:15:43.944: INFO/System.out(3303): </td> 04-30 03:15:43.944: INFO/System.out(3303): 04-30 03:15:43.944: INFO/System.out(3303): <!-- Für Abfragen ohne Karte alternativ Zeile ohne colspan hinzufügen --> 04-30 03:15:43.954: INFO/System.out(3303): 04-30 03:15:43.964: INFO/System.out(3303): <td class="Datum3" height="25" colspan="2"> 04-30 03:15:43.984: INFO/System.out(3303): <select name="DatumT" tabindex="10" id="efaDatumT"> 04-30 03:15:43.984: INFO/System.out(3303): <option >1</option> 04-30 03:15:43.984: INFO/System.out(3303): <option >2</option> 04-30 03:15:43.984: INFO/System.out(3303): <option >3</option> 04-30 03:15:43.984: INFO/System.out(3303): <option >4</option> 04-30 03:15:43.984: INFO/System.out(3303): <option >5</option> 04-30 03:15:43.984: INFO/System.out(3303): <option >6</option> 04-30 03:15:43.984: INFO/System.out(3303): <option >7</option> 04-30 03:15:43.984: INFO/System.out(3303): <option >8</option> 04-30 03:15:43.994: INFO/System.out(3303): <option >9</option> 04-30 03:15:43.994: INFO/System.out(3303): <option >10</option> 04-30 03:15:43.994: INFO/System.out(3303): <option >11</option> 04-30 03:15:43.994: INFO/System.out(3303): <option >12</option> 04-30 03:15:44.005: INFO/System.out(3303): <option >13</option> 04-30 03:15:44.024: INFO/System.out(3303): <option >14</option> 04-30 03:15:44.034: INFO/System.out(3303): <option >15</option> 04-30 03:15:44.034: INFO/System.out(3303): <option >16</option> 04-30 03:15:44.034: INFO/System.out(3303): <option >17</option> 04-30 03:15:44.034: INFO/System.out(3303): <option >18</option> 04-30 03:15:44.044: INFO/System.out(3303): <option >19</option> 04-30 03:15:44.044: INFO/System.out(3303): <option >20</option> 04-30 03:15:44.044: INFO/System.out(3303): <option >21</option> 04-30 03:15:44.044: INFO/System.out(3303): <option >22</option> 04-30 03:15:44.044: INFO/System.out(3303): <option >23</option> 04-30 03:15:44.044: INFO/System.out(3303): <option >24</option> 04-30 03:15:44.044: INFO/System.out(3303): <option >25</option> 04-30 03:15:44.044: INFO/System.out(3303): <option >26</option> 04-30 03:15:44.044: INFO/System.out(3303): <option >27</option> 04-30 03:15:44.044: INFO/System.out(3303): <option >28</option> 04-30 03:15:44.044: INFO/System.out(3303): <option >29</option> 04-30 03:15:44.044: INFO/System.out(3303): <option selected="selected">30</option> 04-30 03:15:44.044: INFO/System.out(3303): <option >31</option> 04-30 03:15:44.055: INFO/System.out(3303): </select> 04-30 03:15:44.055: INFO/System.out(3303): . 04-30 03:15:44.055: INFO/System.out(3303): <select name="DatumM" tabindex="11" id="efaDatumM"> 04-30 03:15:44.055: INFO/System.out(3303): <option >1</option> 04-30 03:15:44.055: INFO/System.out(3303): <option >2</option> 04-30 03:15:44.055: INFO/System.out(3303): <option >3</option> 04-30 03:15:44.064: INFO/System.out(3303): <option selected="selected">4</option> 04-30 03:15:44.064: INFO/System.out(3303): <option >5</option> 04-30 03:15:44.064: INFO/System.out(3303): <option >6</option> 04-30 03:15:44.064: INFO/System.out(3303): <option >7</option> 04-30 03:15:44.064: INFO/System.out(3303): <option >8</option> 04-30 03:15:44.064: INFO/System.out(3303): <option >9</option> 04-30 03:15:44.064: INFO/System.out(3303): <option >10</option> 04-30 03:15:44.064: INFO/System.out(3303): <option >11</option> 04-30 03:15:44.085: INFO/System.out(3303): <option >12</option> 04-30 03:15:44.085: INFO/System.out(3303): </select> 04-30 03:15:44.085: INFO/System.out(3303): . 04-30 03:15:44.085: INFO/System.out(3303): <select name="DatumJ" tabindex="12" id="efaDatumJ"> 04-30 03:15:44.095: INFO/System.out(3303): <option >2009</option> 04-30 03:15:44.095: INFO/System.out(3303): <option selected="selected">2010</option> 04-30 03:15:44.095: INFO/System.out(3303): <option >2011</option> 04-30 03:15:44.095: INFO/System.out(3303): </select> 04-30 03:15:44.095: INFO/System.out(3303): 04-30 03:15:44.095: INFO/System.out(3303): </td> 04-30 03:15:44.095: INFO/System.out(3303): 04-30 03:15:44.105: INFO/System.out(3303): </tr> 04-30 03:15:44.115: INFO/System.out(3303): 04-30 03:15:44.115: INFO/System.out(3303): <tr> 04-30 03:15:44.115: INFO/System.out(3303): <td class="Uhrzeit2"> 04-30 03:15:44.115: INFO/System.out(3303): <input type="radio" name="AbfAnk" value="Abf" checked />Abfahrten ab<br /> 04-30 03:15:44.115: INFO/System.out(3303): <input type="radio" name="AbfAnk" value="Ank" />Ankünfte bis 04-30 03:15:44.115: INFO/System.out(3303): 04-30 03:15:44.115: INFO/System.out(3303): </td> 04-30 03:15:44.125: INFO/System.out(3303): <td class="Uhrzeit3" height="25"> 04-30 03:15:44.125: INFO/System.out(3303): <select name="ZeitH" tabindex="14" id="efaZeitH"> 04-30 03:15:44.125: INFO/System.out(3303): <option >0</option> 04-30 03:15:44.125: INFO/System.out(3303): <option >1</option> 04-30 03:15:44.125: INFO/System.out(3303): <option >2</option> 04-30 03:15:44.135: INFO/System.out(3303): <option >3</option> 04-30 03:15:44.135: INFO/System.out(3303): <option >4</option> 04-30 03:15:44.135: INFO/System.out(3303): <option >5</option> 04-30 03:15:44.135: INFO/System.out(3303): <option >6</option> 04-30 03:15:44.135: INFO/System.out(3303): <option >7</option> 04-30 03:15:44.135: INFO/System.out(3303): <option >8</option> 04-30 03:15:44.145: INFO/System.out(3303): <option >9</option> 04-30 03:15:44.145: INFO/System.out(3303): <option >10</option> 04-30 03:15:44.145: INFO/System.out(3303): <option >11</option> 04-30 03:15:44.145: INFO/System.out(3303): <option >12</option> 04-30 03:15:44.145: INFO/System.out(3303): <option >13</option> 04-30 03:15:44.145: INFO/System.out(3303): <option >14</option> 04-30 03:15:44.145: INFO/System.out(3303): <option selected="selected">15</option> 04-30 03:15:44.145: INFO/System.out(3303): <option >16</option> 04-30 03:15:44.145: INFO/System.out(3303): <option >17</option> 04-30 03:15:44.145: INFO/System.out(3303): <option >18</option> 04-30 03:15:44.145: INFO/System.out(3303): <option >19</option> 04-30 03:15:44.155: INFO/System.out(3303): <option >20</option> 04-30 03:15:44.155: INFO/System.out(3303): <option >21</option> 04-30 03:15:44.155: INFO/System.out(3303): <option >22</option> 04-30 03:15:44.155: INFO/System.out(3303): <option >23</option> 04-30 03:15:44.155: INFO/System.out(3303): </select> 04-30 03:15:44.155: INFO/System.out(3303): : 04-30 03:15:44.155: INFO/System.out(3303): <select name="ZeitM" tabindex="15" id="efaZeitM"> 04-30 03:15:44.155: INFO/System.out(3303): <option >00</option> 04-30 03:15:44.155: INFO/System.out(3303): <option selected="selected">15</option> 04-30 03:15:44.155: INFO/System.out(3303): <option >30</option> 04-30 03:15:44.155: INFO/System.out(3303): <option >45</option> 04-30 03:15:44.155: INFO/System.out(3303): </select> 04-30 03:15:44.155: INFO/System.out(3303): 04-30 03:15:44.155: INFO/System.out(3303): </td> 04-30 03:15:44.155: INFO/System.out(3303): 04-30 03:15:44.165: INFO/System.out(3303): <td class="Uhrzeit2">&nbsp;</td> 04-30 03:15:44.165: INFO/System.out(3303): 04-30 03:15:44.165: INFO/System.out(3303): </tr> 04-30 03:15:44.165: INFO/System.out(3303): 04-30 03:15:44.165: INFO/System.out(3303): <tr> 04-30 03:15:44.165: INFO/System.out(3303): <td class="Intervall2"> 04-30 03:15:44.165: INFO/System.out(3303): Intervall 04-30 03:15:44.165: INFO/System.out(3303): </td> 04-30 03:15:44.184: INFO/System.out(3303): 04-30 03:15:44.184: INFO/System.out(3303): <td class="Intervall3" height="25"> 04-30 03:15:44.184: INFO/System.out(3303): <select name="Intervall" tabindex="13" id="efaIntervall"> 04-30 03:15:44.184: INFO/System.out(3303): <option value="60" >1 h</option> 04-30 03:15:44.184: INFO/System.out(3303): <option value="120" >2 h</option> 04-30 03:15:44.184: INFO/System.out(3303): <option value="240" >4 h</option> 04-30 03:15:44.184: INFO/System.out(3303): <option value="480" >8 h</option> 04-30 03:15:44.184: INFO/System.out(3303): <option value="1800" >ganzer Tag</option> 04-30 03:15:44.194: INFO/System.out(3303): </select> 04-30 03:15:44.194: INFO/System.out(3303): 04-30 03:15:44.204: INFO/System.out(3303): </td> 04-30 03:15:44.204: INFO/System.out(3303): 04-30 03:15:44.204: INFO/System.out(3303): <td class="Intervall3">&nbsp; 04-30 03:15:44.204: INFO/System.out(3303): 04-30 03:15:44.204: INFO/System.out(3303): </tr> 04-30 03:15:44.204: INFO/System.out(3303): </table> 04-30 03:15:44.204: INFO/System.out(3303): 04-30 03:15:44.204: INFO/System.out(3303): </td> 04-30 03:15:44.204: INFO/System.out(3303): 04-30 03:15:44.204: INFO/System.out(3303): <td class="Schalter" valign="top"> 04-30 03:15:44.204: INFO/System.out(3303): <table class="Schalter"> 04-30 03:15:44.204: INFO/System.out(3303): <!-- Buttons --> 04-30 03:15:44.204: INFO/System.out(3303): <tr> 04-30 03:15:44.204: INFO/System.out(3303): <td class="Schalter" align="center"> 04-30 03:15:44.226: INFO/System.out(3303): <input TYPE="Submit" accesskey="s" class="SuchenBtn" name="Suchen" tabindex="20" VALUE="(S)uchen"> 04-30 03:15:44.226: INFO/System.out(3303): </td> 04-30 03:15:44.226: INFO/System.out(3303): </tr> 04-30 03:15:44.226: INFO/System.out(3303): 04-30 03:15:44.226: INFO/System.out(3303): 04-30 03:15:44.226: INFO/System.out(3303): <tr> 04-30 03:15:44.226: INFO/System.out(3303): <td class="Schalter" align="center"> 04-30 03:15:44.226: INFO/System.out(3303): <input TYPE="Submit" accesskey="o" name="Optionen" tabindex="22" VALUE="(O)ptionen"> 04-30 03:15:44.226: INFO/System.out(3303): </td> 04-30 03:15:44.226: INFO/System.out(3303): </tr> 04-30 03:15:44.226: INFO/System.out(3303): 04-30 03:15:44.226: INFO/System.out(3303): 04-30 03:15:44.226: INFO/System.out(3303): <tr> 04-30 03:15:44.226: INFO/System.out(3303): <td class="Schalter" align="center"> 04-30 03:15:44.226: INFO/System.out(3303): <input TYPE="Button" accesskey="z" tabindex="24" VALUE="(Z)urück" onClick="history.back()"> 04-30 03:15:44.226: INFO/System.out(3303): </td> 04-30 03:15:44.226: INFO/System.out(3303): </tr> 04-30 03:15:44.226: INFO/System.out(3303): <tr> 04-30 03:15:44.226: INFO/System.out(3303): <td class="Schalter" align="center"> 04-30 03:15:44.226: INFO/System.out(3303): <input TYPE="Button" accesskey="h" tabindex="25" VALUE="(H)ilfe" onClick="self.location.href='/bs.exe/FF?N=hilfe&amp;SID=3D3B9'"> 04-30 03:15:44.226: INFO/System.out(3303): </td> 04-30 03:15:44.235: INFO/System.out(3303): </tr> 04-30 03:15:44.235: INFO/System.out(3303): <tr> 04-30 03:15:44.235: INFO/System.out(3303): <td class="Schalter" align="center"> 04-30 03:15:44.235: INFO/System.out(3303): <input TYPE="Submit" accesskey="n" tabindex="26" name="Loeschen" VALUE="(N)eue Suche"> 04-30 03:15:44.235: INFO/System.out(3303): </td> 04-30 03:15:44.235: INFO/System.out(3303): </tr> 04-30 03:15:44.235: INFO/System.out(3303): 04-30 03:15:44.235: INFO/System.out(3303): <tr> 04-30 03:15:44.235: INFO/System.out(3303): 04-30 03:15:44.244: INFO/System.out(3303): <td class="Schalter" align="center"> 04-30 03:15:44.244: INFO/System.out(3303): <input TYPE="Button" accesskey="a" tabindex="27" VALUE="H(a)ltestelle" onClick="self.location.href='/bs.exe/RHFF?Karten=true?N=Result&amp;SID=3D3B9'"> 04-30 03:15:44.244: INFO/System.out(3303): </td> 04-30 03:15:44.244: INFO/System.out(3303): 04-30 03:15:44.244: INFO/System.out(3303): </tr> 04-30 03:15:44.244: INFO/System.out(3303): </table> 04-30 03:15:44.254: INFO/System.out(3303): 04-30 03:15:44.254: INFO/System.out(3303): </td> 04-30 03:15:44.254: INFO/System.out(3303): </tr> 04-30 03:15:44.254: INFO/System.out(3303): </table> 04-30 03:15:44.254: INFO/System.out(3303): </form> 04-30 03:15:44.254: INFO/System.out(3303): 04-30 03:15:44.254: INFO/System.out(3303): 04-30 03:15:44.254: INFO/System.out(3303): <!-- Meldungsbereich (automatisch erzeugt) --> 04-30 03:15:44.254: INFO/System.out(3303): <div align="center" id="meldungen"> 04-30 03:15:44.265: INFO/System.out(3303): <table class="Bedienhinweise"><tr><td rowspan="2"><img SRC="http://www.busspur.de/logos/hinweis.png" ALIGN="top" alt="Symbol" WIDTH="32" HEIGHT="20">&nbsp;</td><td rowspan="2">Start</td><td>Geben Sie den Namen der Stadt/Gemeinde ein</td></tr><tr><td>Geben Sie den Namen der Haltestelle ein</td></tr></table> 04-30 03:15:44.265: INFO/System.out(3303): </div> 04-30 03:15:44.265:

  Read the article

• Can't connect to SSL web service with WS-Security using PHP SOAP extension - certificate, complex WSDL

  - by BillF

  Using the PHP5 SOAP extension I have been unable to connect to a web service having an https endpoint, with client certificate and using WS-Security, although I can connect using soapUI with the exact same wsdl and client certificate, and obtain the normal response to the request. There is no HTTP authentication and no proxy is involved. The message I get is 'Could not connect to host'. Have been able to verify that I am NOT hitting the host server. (Earlier I wrongly said that I was hitting the server.) The self-signed client SSL certificate is a .pem file converted by openssl from a .p12 keystore which in turn was converted by keytool from a .jks keystore having a single entry consisting of private key and client certificate. In soapUI I did not need to supply a server private certificate, the only two files I gave it were the wdsl and pem. I did have to supply the pem and its passphrase to be able to connect. I am speculating that despite the error message my problem might actually be in the formation of the XML request rather than the SSL connection itself. The wsdl I have been given has nested complex types. The php server is on my Windows XP laptop with IIS. The code, data values and WSDL extracts are shown below. (The WSSoapClient class simply extends SoapClient, adding a WS-Security Username Token header with mustUnderstand = true and including a nonce, both of which the soapUI call had required.) Would so much appreciate any help. I'm a newbie thrown in at the deep end, and how! Have done vast amounts of Googling on this over many days, following many suggestions and have read Pro PHP by Kevin McArthur. An attempt to use classmaps in place of nested arrays also fell flat. The Code class STEeService { public function invokeWebService(array $connection, $operation, array $request) { try { $localCertificateFilespec = $connection['localCertificateFilespec']; $localCertificatePassphrase = $connection['localCertificatePassphrase']; $sslOptions = array( 'ssl' => array( 'local_cert' => $localCertificateFilespec, 'passphrase' => $localCertificatePassphrase, 'allow_self-signed' => true, 'verify_peer' => false ) ); $sslContext = stream_context_create($sslOptions); $clientArguments = array( 'stream_context' => $sslContext, 'local_cert' => $localCertificateFilespec, 'passphrase' => $localCertificatePassphrase, 'trace' => true, 'exceptions' => true, 'encoding' => 'UTF-8', 'soap_version' => SOAP_1_1 ); $oClient = new WSSoapClient($connection['wsdlFilespec'], $clientArguments); $oClient->__setUsernameToken($connection['username'], $connection['password']); return $oClient->__soapCall($operation, $request); } catch (exception $e) { throw new Exception("Exception in eServices " . $operation . " ," . $e->getMessage(), "\n"); } } } $connection is as follows: array(5) { ["username"]=> string(8) "DFU00050" ["password"]=> string(10) "Fabricate1" ["wsdlFilespec"]=> string (63) "c:/inetpub/wwwroot/DMZExternalService_Concrete_WSDL_Staging.xml" ["localCertificateFilespec"]=> string(37) "c:/inetpub/wwwroot/ClientKeystore.pem" ["localCertificatePassphrase"]=> string(14) "password123456" } $clientArguments is as follows: array(7) { ["stream_context"]=> resource(8) of type (stream-context) ["local_cert"]=> string(37) "c:/inetpub/wwwroot/ClientKeystore.pem" ["passphrase"]=> string(14) "password123456" ["trace"]=> bool(true) ["exceptions"]=> bool(true) ["encoding"]=> string(5) "UTF-8" ["soap_version"]=> int(1) } $operation is as follows: 'getConsignmentDetails' $request is as follows: array(1) { [0]=> array(2) { ["header"]=> array(2) { ["source"]=> string(9) "customerA" ["accountNo"]=> string(8) "10072906" } ["consignmentId"]=> string(11) "GKQ00000085" } } Note how there is an extra level of nesting, an array wrapping the request which is itself an array. This was suggested in a post although I don't see the reason, but it seems to help avoid other exceptions. The exception thrown by ___soapCall is as follows: object(SoapFault)#6 (9) { ["message":protected]=> string(25) "Could not connect to host" ["string":"Exception":private]=> string(0) "" ["code":protected]=> int(0) ["file":protected]=> string(43) "C:\Inetpub\wwwroot\eServices\WSSecurity.php" ["line":protected]=> int(85) ["trace":"Exception":private]=> array(5) { [0]=> array(6) { ["file"]=> string(43) "C:\Inetpub\wwwroot\eServices\WSSecurity.php" ["line"]=> int(85) ["function"]=> string(11) "__doRequest" ["class"]=> string(10) "SoapClient" ["type"]=> string(2) "->" ["args"]=> array(4) { [0]=> string(1240) " DFU00050 Fabricate1 E0ByMUA= 2010-10-28T13:13:52Z customerA10072906GKQ00000085 " [1]=> string(127) "https://services.startrackexpress.com.au:7560/DMZExternalService/InterfaceServices/ExternalOps.serviceagent/OperationsEndpoint1" [2]=> string(104) "/DMZExternalService/InterfaceServices/ExternalOps.serviceagent/OperationsEndpoint1/getConsignmentDetails" [3]=> int(1) } } [1]=> array(4) { ["function"]=> string(11) "__doRequest" ["class"]=> string(39) "startrackexpress\eservices\WSSoapClient" ["type"]=> string(2) "->" ["args"]=> array(5) { [0]=> string(1240) " DFU00050 Fabricate1 E0ByMUA= 2010-10-28T13:13:52Z customerA10072906GKQ00000085 " [1]=> string(127) "https://services.startrackexpress.com.au:7560/DMZExternalService/InterfaceServices/ExternalOps.serviceagent/OperationsEndpoint1" [2]=> string(104) "/DMZExternalService/InterfaceServices/ExternalOps.serviceagent/OperationsEndpoint1/getConsignmentDetails" [3]=> int(1) [4]=> int(0) } } [2]=> array(6) { ["file"]=> string(43) "C:\Inetpub\wwwroot\eServices\WSSecurity.php" ["line"]=> int(70) ["function"]=> string(10) "__soapCall" ["class"]=> string(10) "SoapClient" ["type"]=> string(2) "->" ["args"]=> array(4) { [0]=> string(21) "getConsignmentDetails" [1]=> array(1) { [0]=> array(2) { ["header"]=> array(2) { ["source"]=> string(9) "customerA" ["accountNo"]=> string(8) "10072906" } ["consignmentId"]=> string(11) "GKQ00000085" } } [2]=> NULL [3]=> object(SoapHeader)#5 (4) { ["namespace"]=> string(81) "http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd" ["name"]=> string(8) "Security" ["data"]=> object(SoapVar)#4 (2) { ["enc_type"]=> int(147) ["enc_value"]=> string(594) " DFU00050 Fabricate1 E0ByMUA= 2010-10-28T13:13:52Z " } ["mustUnderstand"]=> bool(true) } } } [3]=> array(6) { ["file"]=> string(42) "C:\Inetpub\wwwroot\eServices\eServices.php" ["line"]=> int(87) ["function"]=> string(10) "__soapCall" ["class"]=> string(39) "startrackexpress\eservices\WSSoapClient" ["type"]=> string(2) "->" ["args"]=> array(2) { [0]=> string(21) "getConsignmentDetails" [1]=> array(1) { [0]=> array(2) { ["header"]=> array(2) { ["source"]=> string(9) "customerA" ["accountNo"]=> string(8) "10072906" } ["consignmentId"]=> string(11) "GKQ00000085" } } } } [4]=> array(6) { ["file"]=> string(58) "C:\Inetpub\wwwroot\eServices\EnquireConsignmentDetails.php" ["line"]=> int(44) ["function"]=> string(16) "invokeWebService" ["class"]=> string(38) "startrackexpress\eservices\STEeService" ["type"]=> string(2) "->" ["args"]=> array(3) { [0]=> array(5) { ["username"]=> string(10) "DFU00050 " ["password"]=> string(12) "Fabricate1 " ["wsdlFilespec"]=> string(63) "c:/inetpub/wwwroot/DMZExternalService_Concrete_WSDL_Staging.xml" ["localCertificateFilespec"]=> string(37) "c:/inetpub/wwwroot/ClientKeystore.pem" ["localCertificatePassphrase"]=> string(14) "password123456" } [1]=> string(21) "getConsignmentDetails" [2]=> array(1) { [0]=> array(2) { ["header"]=> array(2) { ["source"]=> string(9) "customerA" ["accountNo"]=> string(8) "10072906" } ["consignmentId"]=> string(11) "GKQ00000085" } } } } } ["previous":"Exception":private]=> NULL ["faultstring"]=> string(25) "Could not connect to host" ["faultcode"]=> string(4) "HTTP" } Here are some WSDL extracts (TIBCO BusinessWorks): <xsd:complexType name="TransactionHeaderType"> <xsd:sequence> <xsd:element name="source" type="xsd:string"/> <xsd:element name="accountNo" type="xsd:integer"/> <xsd:element name="userId" type="xsd:string" minOccurs="0"/> <xsd:element name="transactionId" type="xsd:string" minOccurs="0"/> <xsd:element name="transactionDatetime" type="xsd:dateTime" minOccurs="0"/> </xsd:sequence> </xsd:complexType> <xsd:element name="getConsignmentDetailRequest"> <xsd:complexType> <xsd:sequence> <xsd:element name="header" type="prim:TransactionHeaderType"/> <xsd:element name="consignmentId" type="prim:ID" maxOccurs="unbounded"/> </xsd:sequence> </xsd:complexType> </xsd:element> <xsd:element name="getConsignmentDetailResponse"> <xsd:complexType> <xsd:sequence> <xsd:element name="consignment" type="freight:consignmentType" minOccurs="0" maxOccurs="unbounded"/> </xsd:sequence> </xsd:complexType> </xsd:element> <xsd:element name="getConsignmentDetailRequest"> <xsd:complexType> <xsd:sequence> <xsd:element name="header" type="prim:TransactionHeaderType"/> <xsd:element name="consignmentId" type="prim:ID" maxOccurs="unbounded"/> </xsd:sequence> </xsd:complexType> </xsd:element> <xsd:element name="getConsignmentDetailResponse"> <xsd:complexType> <xsd:sequence> <xsd:element name="consignment" type="freight:consignmentType" minOccurs="0" maxOccurs="unbounded"/> </xsd:sequence> </xsd:complexType> </xsd:element> <wsdl:operation name="getConsignmentDetails"> <wsdl:input message="tns:getConsignmentDetailsRequest"/> <wsdl:output message="tns:getConsignmentDetailsResponse"/> <wsdl:fault name="fault1" message="tns:fault"/> </wsdl:operation> <wsdl:service name="ExternalOps"> <wsdl:port name="OperationsEndpoint1" binding="tns:OperationsEndpoint1Binding"> <soap:address location="https://services.startrackexpress.com.au:7560/DMZExternalService/InterfaceServices/ExternalOps.serviceagent/OperationsEndpoint1"/> </wsdl:port> </wsdl:service> And here in case it's relevant is the WSSoapClient class: <?PHP namespace startrackexpress\eservices; use SoapClient, SoapVar, SoapHeader; class WSSoapClient extends SoapClient { private $username; private $password; /*Generates a WS-Security header*/ private function wssecurity_header() { $timestamp = gmdate('Y-m-d\TH:i:s\Z'); $nonce = mt_rand(); $passdigest = base64_encode(pack('H*', sha1(pack('H*', $nonce).pack('a*', $timestamp).pack('a*', $this->password)))); $auth = ' <wsse:Security SOAP-ENV:mustUnderstand="1" xmlns:wsse="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd"> <wsse:UsernameToken> <wsse:Username>' . $this->username . '</wsse:Username> <wsse:Password Type="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-username-token-profile-1.0#PasswordText">' . $this->password . '</wsse:Password> <wsse:Nonce>' . base64_encode(pack('H*', $nonce)).'</wsse:Nonce> <wsu:Created xmlns:wsu="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-utility-1.0.xsd">' . $timestamp . '</wsu:Created> </wsse:UsernameToken> </wsse:Security> '; $authvalues = new SoapVar($auth, XSD_ANYXML); $header = new SoapHeader("http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd", "Security",$authvalues, true); return $header; } // Sets a username and passphrase public function __setUsernameToken($username,$password) { $this->username=$username; $this->password=$password; } // Overwrites the original method, adding the security header public function __soapCall($function_name, $arguments, $options=null, $input_headers=null, $output_headers=null) { try { $result = parent::__soapCall($function_name, $arguments, $options, $this->wssecurity_header()); return $result; } catch (exception $e) { throw new Exception("Exception in __soapCall, " . $e->getMessage(), "\n"); } } } ?> Update: The request XML would have been as follows: <?xml version="1.0" encoding="UTF-8"?> <SOAP-ENV:Envelope xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/" xmlns:ns1="http://startrackexpress/Common/Primitives/v1" xmlns:ns2="http://startrackexpress/Common/actions/externals/Consignment/v1" xmlns:ns3="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd"> <SOAP-ENV:Header> <wsse:Security SOAP-ENV:mustUnderstand="1" xmlns:wsse="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd"> <wsse:UsernameToken> <wsse:Username>DFU00050</wsse:Username> <wsse:Password Type="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-username-token-profile-1.0#PasswordText">Fabricate1</wsse:Password> <wsse:Nonce>M4FIeGA=</wsse:Nonce> <wsu:Created xmlns:wsu="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-utility-1.0.xsd">2010-10-29T14:05:27Z</wsu:Created> </wsse:UsernameToken> </wsse:Security> </SOAP-ENV:Header> <SOAP-ENV:Body><ns2:getConsignmentDetailRequest> <ns2:header><ns1:source>customerA</ns1:source><ns1:accountNo>10072906</ns1:accountNo></ns2:header> <ns2:consignmentId>GKQ00000085</ns2:consignmentId> </ns2:getConsignmentDetailRequest></SOAP-ENV:Body> </SOAP-ENV:Envelope> This was obtained with the following code in WSSoapClient: public function __doRequest($request, $location, $action, $version) { echo "<p> " . htmlspecialchars($request) . " </p>" ; return parent::__doRequest($request, $location, $action, $version); }

  Read the article

• IIS SSL Certificate Renewal Pain

  - by Rick Strahl

  I’m in the middle of my annual certificate renewal for the West Wind site and I can honestly say that I hate IIS’s certificate system.  When it works it’s fine, but when it doesn’t man can it be a pain. Because I deal with public certificates on my site merely once a year, and you have to perform the certificate dance just the right way, I seem to run into some sort of trouble every year, thinking that Microsoft surely must have addressed the issues I ran into previously – HA! Not so. Don’t ever use the Renew Certificate Feature in IIS! The first rule that I should have never forgotten is that certificate renewals in IIS (7 is what I’m using but I think it’s no different in 7.5 and 8), simply don’t work if you’re submitting to get a public certificate from a certificate authority. I use DNSimple for my DNS domain management and SSL certificates because they provide ridiculously easy domain management and good prices for SSL certs – especially wildcard certificates, which is what I use on west-wind.com. Certificates in IIS can be found pegged to the machine root. If you go into the IIS Manager, go to the machine root the tree and then click on certificates and you then get various certificate options: Both of these options create a new Certificate request (CSR), which is just a text file. But if you’re silly enough like me to click on the Renew button on your old certificate, you’ll find that you end up generating a very long Certificate Request that looks nothing like the original certificate request and the format that’s used for this is not accepted by most certificate authorities. While I’m not sure exactly what the problem is, it simply looks like IIS is respecting none of your original certificate bit size choices and is generating a huge certificate request that is 3 times the size of a ‘normal’ certificate request. The end result is (and I’ve done this at least twice now) is that the certificate processor is likely to fail processing those renewals. Always create a new Certificate While it’s a little more work and you have to remember how to fill out the certificate request properly, this is the safe way to make sure your certificate generates properly. First comes the Distinguished Name Properties dialog: Ah yes you have to love the nomenclature of this stuff. Distinguished name, Common name – WTF is a common name? It doesn’t look common to me! Make sure this form gets filled out correctly. Common NameThis is the domain name of the Web site. In my case I’m creating a wildcard certificate so I’m using the * prefix. If you’re purchasing a certificate for a specific domain use www.west-wind.com or store.west-wind.com for example. Make sure this matches the EXACT domain you’re trying to use secure access on because that’s all the certificate is going to work on unless you get a wildcard certificate. Organization Is the name of your company or organization. Depending on the kind of certificate you purchase this name will show up on your certificate. Most low end SSL certificates (ie. those that cost under $100 for single domains) don’t list the organization, the higher signature certificates that also require extensive validation by the cert authority do. Regardless you should make sure this matches the right company/organization. Organizational Unit This can be anything. Not really sure what this is for, but traditionally I’ve always set this to Web because – well this is a Web thing after all right? I’ve never seen this used anywhere that I can tell other than to internally reference the cert. State and CountryPretty obvious. Should reflect the location of the business/organization/person or site.   Next you have to configure the bit size used for the certificate: The default on this dialog is 1024, but I’ve found that most providers these days request a minimum bit length of 2048, as did my DNSimple provider. Again check with the provider when you submit to make sure. Bit length mismatches can cause problems if you use a size that isn’t supported by the provider. I had that happen last year when I submitted my CSR and it got rejected quite a bit later, when the certs usually are issued within an hour or less. When you’re done here, the certificate is saved to disk as a .txt file and it should look something like this (this is a 2048 bit length CSR):-----BEGIN NEW CERTIFICATE REQUEST----- MIIEVGCCAz0CAQAwdjELMAkGA1UEBhMCVVMxDzANBgNVBAgMBkhhd2FpaTENMAsG A1UEBwwEUGFpYTEfMB0GA1UECgwWV2VzdCBXaW5kIFRlY2hub2xvZ2llczEMMAoG B1UECwwDV2ViMRgwFgYDVQQDDA8qLndlc3Qtd2luZC5jb20wggEiMA0GCSqGSIb3 DQEBAQUAA4IBDwAwggEKAoIBAQDIPWOFMkMVRp2Ftj9w/cCVV4OYYhoZYtl+8lTk oqDwKca0xWHLgioX/9v0rZLS6a82MHqKEBxVXu+cuCmSE4AQtB/1YH9lS4tpc/be OZDvnTotP6l4MCEzzAfROcw4CiIg6X0RMSnl8IATAvv2V5LQM9TDdt9oDdMpX2IY +vVC9RZ7PMHBmR9kwI2i/lrKitzhQKaHgpmKcRlM6iqpALUiX28w5HJaDKK1MDHN 607tyFJLHijuJKx7PdTqZYf50KkC3NupfZ2avVycf18Q13jHWj59tvwEOczoVzRL l4LQivAqbhyiqMpWnrZunIOUZta5aGm+jo7O1knGWJjxuraTAgMBAAGgggGYMBoG CisGAQQBgjcNAgMxDBYKNi4yLjkyMDAuMjA0BgkrBgEEAYI3FRQxJzAlAgEFDAZS QVNYUFMMC1JBU1hQU1xSaWNrDAtJbmV0TWdyLmV4ZTByBgorBgEEAYI3DQICMWQw YgIBAR5aAE0AaQBjAHIAbwBzAG8AZgB0ACAAUgBTAEEAIABTAEMAaABhAG4AbgBl AGwAIABDAHIAeQBwAHQAbwBnAHIAYQBwAGgAaQBjACAAUAByAG8AdgBpAGQAZQBy AwEAMIHPBgkqhkiG9w0BCQ4xgcEwgb4wDgYDVR0PAQH/BAQDAgTwMBMGA1UdJQQM MAoGCCsGAQUFBwMBMHgGCSqGSIb3DQEJDwRrMGkwDgYIKoZIhvcNAwICAgCAMA4G CCqGSIb3DQMEAgIAgDALBglghkgBZQMEASowCwYJYIZIAWUDBAEtMAsGCWCGSAFl AwQBAjALBglghkgBZQMEAQUwBwYFKw4DAgcwCgYIKoZIhvcNAwcwHQYDVR0OBBYE FD/yOsTbXE+GVFCFMmldzQvyloz9MA0GCSqGSIb3DQEBBQUAA4IBAQCK6LlsCuIM 1AU0niB6QZ9v0FTsGFxP1dYvVUnJyY6VEKNiGFiQjZac7UCs0p58yScdXWEFOE8V OsjAYD3xYNc05+ckyD67UHRGEUAVB9RBvbKW23KeR/8kBmEzc8PemD52YOgExxAJ 57xWmAwEHAvbgYzQvhO8AOzH3TGvvHbg5UKM1pYgNmuwZq5DkL/IDoeIJwfk/wrI wghNTuxxIFgbH4YrgLgv4PRvrS/LaTCRBdboaCgzATMczaOb1nd/DVNR+3fCtMhM W0psTAjzRbmXF3nJyAQa7jF/52gkY0RfFX2lG5tJnG+XDsVNvKNvh9Qa5Tlmkm06 ILKCm9ciWCKk -----END NEW CERTIFICATE REQUEST----- You can take that certificate request and submit that to your certificate provider. Since this is base64 encoded you can typically just paste it into a text box on the submission page, or some providers will ask you to upload the CSR as a file. What does a Renewal look like? Note the length of the CSR will vary somewhat with key strength, but compare this to a renewal request that IIS generated from my existing site:-----BEGIN NEW CERTIFICATE REQUEST----- MIIPpwYFKoZIhvcNAQcCoIIPmDCCD5QCAQExCzAJBgUrDgMCGgUAMIIIqAYJKoZI hvcNAQcBoIIImQSCCJUwggiRMIIH+gIBADBdMSEwHwYDVQQLDBhEb21haW4gQ29u dHJvbCBWYWxpFGF0ZWQxHjAcBgNVBAsMFUVzc2VudGlhbFNTTCBXaWxkY2FyZDEY MBYGA1UEAwwPKi53ZXN0LXdpbmQuY29tMIGfMA0GCSqGSIb3DQEBAQUAA4GNADCB iQKBgQCK4OuIOR18Wb8tNMGRZiD1c9X57b332Lj7DhbckFqLs0ys8kVDHrTXSj+T Ye9nmAvfPpZmBtE5p9qRNN79rUYugAdl+qEtE4IJe1bRfxXzcKa1SXa8+TEs3zQa zYSmcR2dDuC8om1eAdeCtt0NnkvANgm1VLwGOor/UHMASaEhCQIDAQABoIIG8jAa BgorBgEEAYI3DQIDMQwWCjYuMi45MjAwLjIwNAYJKwYBBAGCNxUUMScwJQIBBQwG UkFTWFBTDAtSQVNYUFNcUmljawwLSW5ldE1nci5leGUwZgYKKwYBBAGCNw0CAjFY MFYCAQIeTgBNAGkAYwByAG8AcwBvAGYAdAAgAFMAdAByAG8AbgBnACAAQwByAHkA cAB0AG8AZwByAGEAcABoAGkAYwAgAFAAcgBvAHYAaQBkAGUAcgMBADCCAQAGCSqG SIb3DQEJDjGB8jCB7zAOBgNVHQ8BAf8EBAMCBaAwDAYDVR0TAQH/BAIwADA0BgNV HSUELTArBggrBgEFBQcDAQYIKwYBBQUHAwIGCisGAQQBgjcKAwMGCWCGSAGG+EIE ATBPBgNVHSAESDBGMDoGCysGAQQBsjEBAgIHMCswKQYIKwYBBQUHAgEWHWh0dHBz Oi8vc2VjdXJlLmNvbW9kby5jb20vQ1BTMAgGBmeBDAECATApBgNVHREEIjAggg8q Lndlc3Qtd2luZC5jb22CDXdlc3Qtd2luZC5jb20wHQYDVR0OBBYEFEVLAyO8gDiv lsfovKrx9mHPyrsiMIIFMAYJKwYBBAGCNw0BMYIFITCCBR0wggQFoAMCAQICEQDu 1E1T5Jvtkm5LOfSHabWlMA0GCSqGSIb3DQEBBQUAMHIxCzAJBgNVBAYTAkdCMRsw GQYDVQQIExJHcmVhdGVyIE1hbmNoZXN0ZXIxEDAOBgNVBAcTB1NhbGZvcmQxGjAY BgNVBAoTEUNPTU9ETyBDQSBMaW1pdGVkMRgwFgYDVQQDEw9Fc3NlbnRpYWxTU0wg Q0EwHhcNMTQwNTA3MDAwMDAwWhcNMTUwNjA2MjM1OTU5WjBdMSEwHwYDVQQLExhE b21haW4gQ29udHJvbCBWYWxpZGF0ZWQxHjAcBgNVBAsTFUVzc2VudGlhbFNTTCBX aWxkY2FyZDEYMBYGA1UEAxQPKi53ZXN0LXdpbmQuY29tMIIBIjANBgkqhkiG9w0B AQEFAAOCAQ8AMIIBCgKCAQEAiyKfL66XB51DlUfm6xXqJBcvMU2qorRHxC+WjEpB amvg8XoqNfCKzDAvLMbY4BLhbYCTagqtslnP3Gj4AKhXqRKU0n6iSbmS1gcWzCJM CHufZ5RDtuTuxhTdJxzP9YqZUfKV5abWQp/TK6V1ryaBJvdqM73q4tRjrQODtkiR PfZjxpybnBHFJS8jYAf8jcOjSDZcgN1d9Evc5MrEJCp/90cAkozyF/NMcFtD6Yj8 UM97z3MzDT2JPDoH3kAr3cCgpUNyQ2+wDNCnL9eWYFkOQi8FZMsZol7KlZ5NgNfO a7iZMVGbqDg6rkS//2uGe6tSQJTTs+mAZB+na+M8XT2UqwIDAQABo4IBwTCCAb0w HwYDVR0jBBgwFoAU2svqrVsIXcz//CZUzknlVcY49PgwHQYDVR0OBBYEFH0AmLiL RSEL9+sQD/n5O4N7/nnqMA4GA1UdDwEB/wQEAwIFoDAMBgNVHRMBAf8EAjAAMDQG A1UdJQQtMCsGCCsGAQUFBwMBBggrBgEFBQcDAgYKKwYBBAGCNwoDAwYJYIZIAYb4 QgQBME8GA1UdIARIMEYwOgYLKwYBBAGyMQECAgcwKzApBggrBgEFBQcCARYdaHR0 cHM6Ly9zZWN1cmUuY29tb2RvLmNvbS9DUFMwCAYGZ4EMAQIBMDsGA1UdHwQ0MDIw MKAuoCyGKmh0dHA6Ly9jcmwuY29tb2RvY2EuY29tL0Vzc2VudGlhbFNTTENBLmNy bDBuBggrBgEFBQcBAQRiMGAwOAYIKwYBBQUHMAKGLGh0dHA6Ly9jcnQuY29tb2Rv Y2EuY29tL0Vzc2VudGlhbFNTTENBXzIuY3J0MCQGCCsGAQUFBzABhhhodHRwOi8v b2NzcC5jb21vZG9jYS5jb20wKQYDVR0RBCIwIIIPKi53ZXN0LXdpbmQuY29tgg13 ZXN0LXdpbmQuY29tMA0GCSqGSIb3DQEBBQUAA4IBAQBqBfd6QHrxXsfgfKARG6np 8yszIPhHGPPmaE7xq7RpcZjY9H+8l6fe4jQbGFjbA5uHBklYI4m2snhPaW2p8iF8 YOkm2V2hEsSTnkf5/flw9mZtlCFEDFXSsBxBdNz8RYTthPMu1h09C0XuDB30sztg nR692FrxJN5/bXsk+MC9nEweTFW/t2HW+XZ8bhM7vsAS+pZionR4MyuQ0mYIt/lD csZVZ91KxTsIm8rNMkkYGFoSIXjQ0+0tCbxMF0i2qnpmNRpA6PU8l7lxxvPkplsk 9KB8QIPFrR5p/i/SUAd9vECWh5+/ktlcrfFP2PK7XcEwWizsvMrNqLyvQVNXSUPT MA0GCSqGSIb3DQEBBQUAA4GBABt/NitwMzc5t22p5+zy4HXbVYzLEjesLH8/v0ot uLQ3kkG8tIWNh5RplxIxtilXt09H4Oxpo3fKUN0yw+E6WsBfg0sAF8pHNBdOJi48 azrQbt4HvKktQkGpgYFjLsormjF44SRtToLHlYycDHBNvjaBClUwMCq8HnwY6vDq xikRoIIFITCCBR0wggQFoAMCAQICEQDu1E1T5Jvtkm5LOfSHabWlMA0GCSqGSIb3 DQEBBQUAMHIxCzAJBgNVBAYTAkdCMRswGQYDVQQIExJHcmVhdGVyIE1hbmNoZXN0 ZXIxEDAOBgNVBAcTB1NhbGZvcmQxGjAYBgNVBAoTEUNPTU9ETyBDQSBMaW1pdGVk MRgwFgYDVQQDEw9Fc3NlbnRpYWxTU0wgQ0EwHhcNMTQwNTA3MDAwMDAwWhcNMTUw NjA2MjM1OTU5WjBdMSEwHwYDVQQLExhEb21haW4gQ29udHJvbCBWYWxpZGF0ZWQx HjAcBgNVBAsTFUVzc2VudGlhbFNTTCBXaWxkY2FyZDEYMBYGA1UEAxQPKi53ZXN0 LXdpbmQuY29tMIIBIjANBgkqhkiG9w0BAQEFAAOCAQ8AMIIBCgKCAQEAiyKfL66X B51DlUfm6xXqJBcvMU2qorRHxC+WjEpBamvg8XoqNfCKzDAvLMbY4BLhbYCTagqt slnP3Gj4AKhXqRKU0n6iSbmS1gcWzCJMCHufZ5RDtuTuxhTdJxzP9YqZUfKV5abW Qp/TK6V1ryaBJvdqM73q4tRjrQODtkiRPfZjxpybnBHFJS8jYAf8jcOjSDZcgN1d 9Evc5MrEJCp/90cAkozyF/NMcFtD6Yj8UM97z3MzDT2JPDoH3kAr3cCgpUNyQ2+w DNCnL9eWYFkOQi8FZMsZol7KlZ5NgNfOa7iZMVGbqDg6rkS//2uGe6tSQJTTs+mA ZB+na+M8XT2UqwIDAQABo4IBwTCCAb0wHwYDVR0jBBgwFoAU2svqrVsIXcz//CZU zknlVcY49PgwHQYDVR0OBBYEFH0AmLiLRSEL9+sQD/n5O4N7/nnqMA4GA1UdDwEB /wQEAwIFoDAMBgNVHRMBAf8EAjAAMDQGA1UdJQQtMCsGCCsGAQUFBwMBBggrBgEF BQcDAgYKKwYBBAGCNwoDAwYJYIZIAYb4QgQBME8GA1UdIARIMEYwOgYLKwYBBAGy MQECAgcwKzApBggrBgEFBQcCARYdaHR0cHM6Ly9zZWN1cmUuY29tb2RvLmNvbS9D UFMwCAYGZ4EMAQIBMDsGA1UdHwQ0MDIwMKAuoCyGKmh0dHA6Ly9jcmwuY29tb2Rv Y2EuY29tL0Vzc2VudGlhbFNTTENBLmNybDBuBggrBgEFBQcBAQRiMGAwOAYIKwYB BQUHMAKGLGh0dHA6Ly9jcnQuY29tb2RvY2EuY29tL0Vzc2VudGlhbFNTTENBXzIu Y3J0MCQGCCsGAQUFBzABhhhodHRwOi8vb2NzcC5jb21vZG9jYS5jb20wKQYDVR0R BCIwIIIPKi53ZXN0LXdpbmQuY29tgg13ZXN0LXdpbmQuY29tMA0GCSqGSIb3DQEB BQUAA4IBAQBqBfd6QHrxXsfgfKARG6np8yszIPhHGPPmaE7xq7RpcZjY9H+8l6fe 4jQbGFjbA5uHBklYI4m2snhPaW2p8iF8YOkm2V2hEsSTnkf5/flw9mZtlCFEDFXS sBxBdNz8RYTthPMu1h09C0XuDB30sztgnR692FrxJN5/bXsk+MC9nEweTFW/t2HW +XZ8bhM7vsAS+pZionR4MyuQ0mYIt/lDcsZVZ91KxTsIm8rNMkkYGFoSIXjQ0+0t CbxMF0i2qnpmNRpA6PU8l7lxxvPkplsk9KB8QIPFrR5p/i/SUAd9vECWh5+/ktlc rfFP2PK7XcEwWizsvMrNqLyvQVNXSUPTMYIBrzCCAasCAQEwgYcwcjELMAkGA1UE BhMCR0IxGzAZBgNVBAgTEkdyZWF0ZXIgTWFuY2hlc3RlcjEQMA4GA1UEBxMHU2Fs Zm9yZDEaMBgGA1UEChMRQ09NT0RPIENBIExpbWl0ZWQxGDAWBgNVBAMTD0Vzc2Vu dGlhbFNTTCBDQQIRAO7UTVPkm+2Sbks59IdptaUwCQYFKw4DAhoFADANBgkqhkiG 9w0BAQEFAASCAQB8PNQ6bYnQpWfkHyxnDuvNKw3wrqF2p7JMZm+SuN2qp3R2LpCR mW2LrGtQIm9Iob/QOYH+8houYNVdvsATGPXX2T8gzn+anof4tOG0vCTK1Bp9bwf9 MkRP+1c8RW/vkYmUW4X5/C+y3CZpMH5dDTaXBIpXFzjX/fxNpH/rvLzGiaYYL3Cn OLO+aOADr9qq5yoqwpiYCSfYNNYKTUNNGfYIidQwYtbHXEYhSukB2oR89xD2sZZ4 bOqFjUPgTa5SsERLDDeg3omMKiIXVYGxlqBEq51Kge6IQt4qQV9P9VgInW7cWmKe dTqNHI9ri3ttewdEnT++TKGKKfTjX9SR8Waj -----END NEW CERTIFICATE REQUEST----- Clearly there’s something very different between this an my original request! And it didn’t work. IIS creates a custom CSR that is encoded in a format that no certificate authority I’ve ever used uses. If you want the gory details of what’s in there look at this ServerFault question (thanks to Mika in the comments). In the end it doesn’t matter  though – no certificate authority knows what to do with this CSR. So create a new CSR and skip the renewal. Always! Use the same Server Keep in mind that on IIS at least you should always create your certificate on a single server and then when you receive the final certificate from your provider import it on that server. IIS tracks the CSR it created and requires it in order to import the final certificate properly. So if for some reason you try to install the certificate on another server, it won’t work. I’ve also run into trouble trying to install the same certificate twice – this time around I didn’t give my certificate the proper friendly name and IIS failed to allow me to assign the certificate to any of my Web sites. So I removed the certificate and tried to import again, only to find it failed the second time around. There are other ways to fix this, but in my case I had to have the certificate re-issued to work – not what you want to do. Regardless of what you do though, when you import make sure you do it right the first time by crossing all your t’s and dotting your i's– it’ll save you a lot of grief! You don’t actually have to use the server that the certificate gets installed on to generate the CSR and first install it, but it is generally a good idea to do so just so you can get the certificate installed into the right place right away. If you have access to the server where you need to install the certificate you might as well use it. But you can use another machine to generated the and install the certificate, then export the certificate and move it to another machine as needed. So you can use your Dev machine to create a certificate then export it and install it on a live server. More on installation and back up/export later. Installing the Certificate Once you’ve submitted a CSR request your provider will process the request and eventually issue you a new final certificate that contains another text file with the final key to import into your certificate store. IIS does this by combining the content in your certificate request with the original CSR. If all goes well your new certificate shows up in the certificate list and you’re ready to assign the certificate to your sites. Make sure you use a friendly name that matches domain name of your site. So use *.mysite.com or www.mysite.com or store.mysite.com to ensure IIS recognizes the certificate. I made the mistake of not naming my friendly name this way and found that IIS was unable to link my sites to my wildcard certificate. It needed to have the *. as part of the certificate otherwise the Hostname input field was blanked out. Changing the Friendly Name If you by accidentally used an invalid friendly name you can change it later in the Windows certificate store. Bring up a Run Box Type MMC File | Add/Remove Snap In Add Certificates | Computer Account | Local Computer Drill into Certificates | Personal | Certificates Find your Certificate | Right Click | Properties Edit the Friendly Name | Click OK Backing up your Certificate The first thing you should do once your certificate is successfully installed is to back it up! In case your server crashes or you otherwise lose your configuration this will ensure you have an easy way to recover and reinstall your certificate either on the same server or a different one. If you’re running a server farm or using a wildcard certificate you also need to get the certificate onto other machines and a PFX file import is the easiest way to do this. To back up your certificate select your certificate and choose Export from the context or sidebar menu: The Export Certificate option allows you to export a password protected binary file that you can import in a single step. You can copy the resulting binary PFX file to back up or copy to other machines to install on. Importing the certificate on another machine is as easy as pointing at the PFX file and specifying the password. IIS handles the rest. Assigning a new certificate to your Site Once you have the new certificate installed, all that’s left to do is assign it to your site. In IIS select your Web site and bring up the Site Bindings from the right sidebar. Add a new binding for https, bind it to port 443, specify your hostname and pick the certificate from the pick list. If you’re using a root site make sure to set up your certificate for www.yoursite.com and also for yoursite.com so that both work properly with SSL. Note that you need to explicitly configure each hostname for a certificate if you plan to use SSL. Luckily if you update your SSL certificate in the following year, IIS prompts you and asks whether you like to update all other sites that are using the existing cert to the newer cert. And you’re done. So what’s the Pain? So, all of this is old hat and it doesn’t look all that bad right? So what’s the pain here? Well if you follow the instructions and do everything right, then the process is about as straight forward as you would expect it to be. You create a cert request, you import it and assign it to your sites. That’s the basic steps and to be perfectly fair it works well – if nothing goes wrong. However, renewing tends to be the problem. The first unintuitive issue is that you simply shouldn’t renew but create a new CSR and generate your new certificate from that. Over the years I’ve fallen prey to the belief that Microsoft eventually will fix this so that the renewal creates the same type of CSR as the old cert, but apparently that will just never happen. Booo! The other problem I ran into is that I accidentally misnamed my imported certificate which in turn set off a chain of events that caused my originally issued certificate to become uninstallable. When I received my completed certificate I installed it and it installed just fine, but the friendly name was wrong. As a result IIS refused to assign the certificate to any of my host headered sites. That’s strike number one. Why the heck should the friendly name have any effect on the ability to attach the certificate??? Next I uninstalled the certificate because I figured that would be the easiest way to make sure I get it right. But I found that I could not reinstall my certificate. I kept getting these stop errors: "ASN1 bad tag value met" that would prevent the installation from completion. After searching around for this error and reading countless long messages on forums, I found that this error supposedly does not actually mean the install failed, but the list wouldn’t refresh. Commodo has this to say: Note: There is a known issue in IIS 7 giving the following error: "Cannot find the certificate request associated with this certificate file. A certificate request must be completed on the computer where it was created." You may also receive a message stating "ASN1 bad tag value met". If this is the same server that you generated the CSR on then, in most cases, the certificate is actually installed. Simply cancel the dialog and press "F5" to refresh the list of server certificates. If the new certificate is now in the list, you can continue with the next step. If it is not in the list, you will need to reissue your certificate using a new CSR (see our CSR creation instructions for IIS 7). After creating a new CSR, login to your Comodo account and click the 'replace' button for your certificate. Not sure if this issue is fixed in IIS 8 but that’s an insane bug to have crop up. As it turns out, in my case the refresh didn’t work and the certificate didn’t show up in the IIS list after the reinstall. In fact when looking at the certificate store I could see my certificate was installed in the right place, but the private key is missing which is most likely why IIS is not picking it up. It looks like IIS could not match the final cert to the original CSR generated. But again some sort of message to that affect might be helpful instead of ASN1 bad tag value met. Recovering the Private Key So it turns out my original problem was that I received the published key, but when I imported the private key was missing. There’s a relatively easy way to recover from this. If your certificate doesn’t show up in IIS check in the certificate store for the local machine (see steps above on how to bring this up). If you look at the certificate in Certificates/Personal/Certificates make sure you see the key as shown in the image below: if the key is missing it means that the certificate is missing the private key most likely. To fix a certificate you can do the following: Double click the certificate Go to the Details Tab Copy down the Serial number You can copy the serial number from the area blurred out above. The serial number will be in a format like ?00 a7 9b a1 a4 9d 91 63 57 d6 9f 26 b8 ee 79 b5 cb and you’ll need to strip out the spaces in order to use it in the next step. Next open up an Administrative command prompt and issue the following command: certutil -repairstore my 00a79ba1a49d916357d69f26b8ee79b5cb You should get a confirmation message that the repair worked. If you now go back to the certificate store you should now see the key icon show up on the certificate. Your certificate is fixed. Now go back into IIS Manager and refresh the list of certificates and if all goes well you should see all the certificates that showed in the cert store now: Remember – back up the key first then map to your site… Summary I deal with a lot of customers who run their own IIS servers, and I can’t tell you how often I hear about botched SSL installations. When I posted some of my issues on Twitter yesterday I got a hell storm of “me too” responses. I’m clearly not the only one, who’s run into this especially with renewals. I feel pretty comfortable with IIS configuration and I do a lot of it for support purposes, but the SSL configuration is one that never seems to go seamlessly. This blog post is meant as reminder to myself to read next time I do a renewal. So I can dot my i's and dash my t’s before I get caught in the mess I’m dealing with today. Hopefully some of you find this useful as well.© Rick Strahl, West Wind Technologies, 2005-2014Posted in IIS7  Security   Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs"); (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

  Read the article

• Using Unity – Part 2

  - by nmarun

  In the first part of this series, we created a simple project and learned how to implement IoC pattern using Unity. In this one, I’ll show how you can instantiate other types that implement our IProduct interface. One place where this one would want to use this feature is to create mock types for testing purposes. Alright, let’s dig in. I added another class – Product2.cs  to the ProductModel project. 1: public class Product2 : IProduct 2: { 3: public string Name { get; set;} 4: public Category Category { get; set; } 5: public DateTime MfgDate { get;set; } 6:  7: public Product2() 8: { 9: Name = "Canon Digital Rebel XTi"; 10: Category = new Category {Name = "Electronics", SubCategoryName = "Digital Cameras"}; 11: MfgDate = DateTime.Now; 12: } 13:  14: public string WriteProductDetails() 15: { 16: return string.Format("Name: {0}<br/>Category: {1}<br/>Mfg Date: {2}", 17: Name, Category, MfgDate.ToShortDateString()); 18: } 19: } Highlights of this class are that it implements IProduct interface and it has some different properties than the Product class. The Category class looks like below: 1: public class Category 2: { 3: public string Name { get; set; } 4: public string SubCategoryName { get; set; } 5:  6: public override string ToString() 7: { 8: return string.Format("{0} - {1}", Name, SubCategoryName); 9: } 10: } We’ll go to our web.config file to add the configuration information about this new class – Product2 that we created. Let’s first add a typeAlias element. 1: <typeAlias alias="Product2" type="ProductModel.Product2, ProductModel"/> That’s all that is needed for us to get an instance of Product2 in our application. I have a new button added to the .aspx page and the click event of this button is where all the magic happens: 1: private IUnityContainer unityContainer; 2: protected void Page_Load(object sender, EventArgs e) 3: { 4: unityContainer = Application["UnityContainer"] as IUnityContainer; 5: 6: if (unityContainer == null) 7: { 8: productDetailsLabel.Text = "ERROR: Unity Container not populated in Global.asax.<p />"; 9: } 10: else 11: { 12: if (!IsPostBack) 13: { 14: IProduct productInstance = unityContainer.Resolve<IProduct>(); 15: productDetailsLabel.Text = productInstance.WriteProductDetails(); 16: } 17: } 18: } 19:  20: protected void Product2Button_Click(object sender, EventArgs e) 21: { 22: unityContainer.RegisterType<IProduct, Product2>(); 23: IProduct product2Instance = unityContainer.Resolve<IProduct>(); 24: productDetailsLabel.Text = product2Instance.WriteProductDetails(); 25: } The unityContainer instance is set in the Page_Load event. Line 22 in the click event of the Product2Button registers a type mapping in the container. In English, this means that when unityContainer tries to resolve for IProduct, it gets an instance of Product2. Once this code runs, following output is rendered: There’s another way of doing this. You can resolve an instance of the requested type with a name from the container. We’ll have to update the container element of our web.config file to include the following: 1: <container name="unityContainer"> 2: <types> 3: <type type="IProduct" mapTo="Product"/> 4: <!-- Named mapping for IProduct to Product --> 5: <type type="IProduct" mapTo="Product" name="LegacyProduct" /> 6: <!-- Named mapping for IProduct to Product2 --> 7: <type type="IProduct" mapTo="Product2" name="NewProduct" /> 8: </types> 9: </container> I’ve added a Dropdownlist and a button to the design page: 1: <asp:DropDownList ID="ModelTypesList" runat="server"> 2: <asp:ListItem Text="Legacy Product" Value="LegacyProduct" /> 3: <asp:ListItem Text="New Product" Value="NewProduct" /> 4: </asp:DropDownList> 5: <br /> 6: <asp:Button ID="SelectedModelButton" Text="Get Selected Instance" runat="server" 7: onclick="SelectedModelButton_Click" /> 1: protected void SelectedModelButton_Click(object sender, EventArgs e) 2: { 3: // get the selected value: LegacyProduct or NewProduct 4: string modelType = ModelTypesList.SelectedValue; 5: // pass the modelType to the Resolve method 6: IProduct customModel = unityContainer.Resolve<IProduct>(modelType); 7: productDetailsLabel.Text = customModel.WriteProductDetails(); 8: } Pretty straight forward right? The only thing to note here is that the values in the dropdownlist item need to match the name attribute of the type. Depending on what you select, you’ll get an instance of either the Product class or the Product2 class and the corresponding WriteProductDetails() method is called. Now you see, how either of these methods can be used to create mock objects your the test project. See the code here. I’ll continue to share more of Unity in the next blog.

  Read the article

• Start a Mapping or Process Flow from OWB Browser

  - by Dong Ruirong

  Basically, we start a Mapping or Process Flow from Oracle Warehouse Builder (OWB) Design Client. But actually we can also start a Mapping or Process Flow from OWB Browser. This paper will introduce the Start Report first and then introduce how to start/rerun a Mapping or Process Flow from OWB Browser. Start Report Start Report is used to start an execution of a Mapping or Process Flow. So there are two kinds of Start Report: Mapping Start Report (See Figure 1) and Process Flow Start Report (See Figure 2). Start Report shows the Mapping or Process Flow identification properties, including latest deployment and latest execution, lists all execution parameters for the Mapping or Process Flow, which were specified by the latest deployment, and assigns parameter default values from the latest deployment specification. You can do a couple of things from Start Report: Sort execution parameters on name, category. Table 1 lists all parameters of a Mapping. Table 2 lists all parameters of a Process Flow. Change values of any input parameter where permitted. For some parameters, selection lists are provided. For example, Mapping’s parameter Audit Level has a selection list. Reset all parameter settings to their default values. Apply basic validation to parameter values before starting an execution. Start the Mapping or Process Flow, which means it is executed immediately. Navigate to Deployment Report for latest deployment details of the Mapping or Process Flow. Navigate to Execution Job Report for latest execution of current Mapping or Process Flow Link to on-link help Warehouse Report Page, Deployment Report, Execution Report, Execution Schedule Report and Execution Summary Report. Figure 1 Mapping Start Report Table 1 Execution Parameters and default values for a Mapping Category Name Mode Input Value System Audit Level In Error Details System Bulk Size In 1000 System Commit Frequency In 1000 System EXECUTE_RESUME_TASK In FALSE System FORCE_RESUME_OPTION In FALSE System Max No of Errors In 50 System NUMBER_OF_TIMES_TO_RETRY In 2 System Operating Mode In Set Based Fail Over to Row Based System PARALLEL_LEVEL In 0 System Procedure Name In main System Purge Group In WB Figure 2 Process Flow Start Report Table 2 Execution Parameters and default values for a Process Flow Category Name Mode Input Value System EVAL_LOCATION In   System Item Key In-Out   System Item Type In PFPKG_1 Start a Mapping or Process Flow To navigate to Start Report, it’s better to login OWB Browser with Control Center option; if not, after logging in OWB Browser, go to Control Center first. Then you can follow the ways introduced in this section to navigate to Start Report. One more thing you need to pay attention to is that you are not allowed to deploy any Mappings and Process Flows from OWB Browser as it’s not supported. So it’s necessary to deploy the Mappings and Process Flows first before starting them from OWB Browser. If you have deployed a Mapping or Process Flow but have not started it, please navigate from Object Summary Report or Deployment Schedule Report to Start Report. 1. Navigating from Object Summary Report to Start Report Open the Object Summary Report to see all deployed Mappings and Process Flows. Click the Mapping Name or Process Flow Name link to see its Deployment Report. Select the Start link in the Available Reports tab for the given Mapping or Process Flow to display a Start Report for the Mapping or Process Flow. The execution parameters have the default deployment-time settings. Change any of the input parameter values as required. Click Start Execution button to execute the Mapping or Process Flow. 2. Navigating from Deployment Schedule Report to Start Report Open the Deployment Schedule Report to see deployment details of Mapping and Process Flow. Expand the project trees to find the deployed Mappings and Process Flows. Click the Mapping Name or Process Flow Name link to see its Deployment Report. Select the Start link in the Available Reports tab for the given Mapping or Process Flow to display a Start Report for the Mapping or Process Flow. The execution parameters have the default deployment-time settings. Change any of the input parameter values as required. Click Start Execution button to execute the Mapping or Process Flow. Re-run a Mapping or Process Flow If you have executed a Mapping or Process Flow, you can navigate from Object Summary Report, Deployment Schedule Report, Execution Summary Report or Execution Schedule Report to Start Report. 1. Navigating from the Execution Summary Report to Start Report Open the Execution Summary Report to see all execution jobs including Mapping jobs and Process Flow jobs. Click on the Mapping Name or Process Flow Name to see its Execution Report. Select the Start link in the Available Reports tab for the given Mapping or Process Flow to display a Start Report for the Mapping or Process Flow. The execution parameters have the default deployment-time settings. Change any of the input parameter values as required. Click Start Execution button to execute the Mapping or Process Flow. 2. Navigating from the Execution Schedule Report to Start Report Open the Execution Schedule Report to see list of all executions of Mapping and Process Flow. Click on the Mapping Name or Process Flow Name to see its Execution Report. Select the Start link in the Available Reports tab for the given Mapping or Process Flow to display a Start Report for the Mapping or Process Flow. The execution parameters have the default deployment-time settings. Change any of the input parameter values as required. Click Start Execution button to execute the Mapping or Process Flow. If the execution of a Mapping or Process Flow is successful, you will see this message from the Start Report: Start Execution request successful. (See Figure 3) Figure 3 Execution Result You can also confirm the execution of the Mapping or Process Flow by referring to Execution Report of the current Mapping or Process Flow by clicking the link in the Available Reports tab for the given Mapping or Process Flow. One new record of execution job details is added to Execution Report of the Mapping or Process Flow which shows the details of the execution such as Start Time, Elapsed Time, Status, the number of records selected, inserted, updated, deleted etc.

  Read the article

• readonly keyword

  - by nmarun

  This is something new that I learned about the readonly keyword. Have a look at the following class: 1: public class MyClass 2: { 3: public string Name { get; set; } 4: public int Age { get; set; } 5:  6: private readonly double Delta; 7:  8: public MyClass() 9: { 10: Initializer(); 11: } 12:  13: public MyClass(string name = "", int age = 0) 14: { 15: Name = name; 16: Age = age; 17: Initializer(); 18: } 19:  20: private void Initializer() 21: { 22: Delta = 0.2; 23: } 24: } I have a couple of public properties and a private readonly member. There are two constructors – one that doesn’t take any parameters and the other takes two parameters to initialize the public properties. I’m also calling the Initializer method in both constructors to initialize the readonly member. Now when I build this, the code breaks and the Error window says: “A readonly field cannot be assigned to (except in a constructor or a variable initializer)” Two things after I read this message: It’s such a negative statement. I’d prefer something like: “A readonly field can be assigned to (or initialized) only in a constructor or through a variable initializer” But in my defense, I AM assigning it in a constructor (only indirectly). All I’m doing is creating a method that does it and calling it in a constructor. Turns out, .net was not ‘frameworked’ this way. We need to have the member initialized directly in the constructor. If you have multiple constructors, you can just use the ‘this’ keyword on all except the default constructors to call the default constructor. This default constructor can then initialize your readonly members. This will ensure you’re not repeating the code in multiple places. A snippet of what I’m talking can be seen below: 1: public class Person 2: { 3: public int UniqueNumber { get; set; } 4: public string Name { get; set; } 5: public int Age { get; set; } 6: public DateTime DateOfBirth { get; set; } 7: public string InvoiceNumber { get; set; } 8:  9: private readonly string Alpha; 10: private readonly int Beta; 11: private readonly double Delta; 12: private readonly double Gamma; 13:  14: public Person() 15: { 16: Alpha = "FDSA"; 17: Beta = 2; 18: Delta = 3.0; 19: Gamma = 0.0989; 20: } 21:  22: public Person(int uniqueNumber) : this() 23: { 24: UniqueNumber = uniqueNumber; 25: } 26: } See the syntax in line 22 and you’ll know what I’m talking about. So the default constructor gets called before the one in line 22. These are known as constructor initializers and they allow one constructor to call another. The other ‘myth’ I had about readonly members is that you can set it’s value only once. This was busted as well (I recall Adam and Jamie’s show). Say you’ve initialized the readonly member through a variable initializer. You can over-write this value in any of the constructors any number of times. 1: public class Person 2: { 3: public int UniqueNumber { get; set; } 4: public string Name { get; set; } 5: public int Age { get; set; } 6: public DateTime DateOfBirth { get; set; } 7: public string InvoiceNumber { get; set; } 8:  9: private readonly string Alpha = "asdf"; 10: private readonly int Beta = 15; 11: private readonly double Delta = 0.077; 12: private readonly double Gamma = 1.0; 13:  14: public Person() 15: { 16: Alpha = "FDSA"; 17: Beta = 2; 18: Delta = 3.0; 19: Gamma = 0.0989; 20: } 21:  22: public Person(int uniqueNumber) : this() 23: { 24: UniqueNumber = uniqueNumber; 25: Beta = 3; 26: } 27:  28: public Person(string name, DateTime dob) : this() 29: { 30: Name = name; 31: DateOfBirth = dob; 32:  33: Alpha = ";LKJ"; 34: Gamma = 0.0898; 35: } 36:  37: public Person(int uniqueNumber, string name, int age, DateTime dob, string invoiceNumber) : this() 38: { 39: UniqueNumber = uniqueNumber; 40: Name = name; 41: Age = age; 42: DateOfBirth = dob; 43: InvoiceNumber = invoiceNumber; 44:  45: Alpha = "QWER"; 46: Beta = 5; 47: Delta = 1.0; 48: Gamma = 0.0; 49: } 50: } In the above example, every constructor over-writes the values for the readonly members. This is perfectly valid. There is a possibility that based on the way the object is instantiated, the readonly member will have a different value. Well, that’s all I have for today and read this as it’s on a related topic.

  Read the article

• Create a Self Signed Sertificate on WLS 10.3.5 Supporting SHA 256 Algorthim.

  - by adejuanc

  1) Set domain to call the keytool $. setDomainEnv.sh 2) Generate the key $ keytool -genkey -alias selfsignedcert -keyalg RSA -sigalg SHA256withRSA -keypass privatepassword -keystore identity.jks -storepass password -validity 365 What is your first and last name? [Unknown]: adejuan-desktop.cl.oracle.com What is the name of your organizational unit? [Unknown]: a What is the name of your organization? [Unknown]: e What is the name of your City or Locality? [Unknown]: i What is the name of your State or Province? [Unknown]: o What is the two-letter country code for this unit? [Unknown]: U Is CN=adejuan-desktop.cl.oracle.com, OU=a, O=e, L=i, ST=o, C=U correct? [no]: yes 3) Export the root certificate $ keytool -export -alias selfsignedcert -sigalg SHA256withRSA -file root.cer -keystore identity.jks Enter keystore password: Certificate stored in file <root.cer> 4) Import the root certificate to the trust store $ keytool -import -alias selfsignedcert -sigalg SHA256withRSA -trustcacerts -file root.cer -keystore trust.jks Enter keystore password: Re-enter new password: Owner: CN=adejuan-desktop.cl.oracle.com, OU=a, O=e, L=i, ST=o, C=U Issuer: CN=adejuan-desktop.cl.oracle.com, OU=a, O=e, L=i, ST=o, C=U Serial number: 4f17459a Valid from: Wed Jan 16 15:33:22CLST 2012 until: Thu Jan 15 15:33:22 CLST 2013 Certificate fingerprints: MD5: 7F:08:FA:DE:CD:D5:C3:D3:83:ED:B8:4F:F2:DA:4E:A1 SHA1: 87:E4:7C:B8:D7:1A:90:53:FE:1B:70:B6:32:22:5B:83:29:81:53:4B Signature algorithm name: SHA256withRSA Version: 3 Trust this certificate? [no]: yes Certificate was added to keystore 5) To check the contents of the keystore keytool -v -list -keystore identity.jks Enter keystore password: ***************** WARNING WARNING WARNING ***************** * The integrity of the information stored in your keystore * * has NOT been verified! In order to verify its integrity, * * you must provide your keystore password. * ***************** WARNING WARNING WARNING ***************** Keystore type: JKS Keystore provider: SUN Your keystore contains 1 entry Alias name: selfsignedcert Creation date: Jan 18, 2012 Entry type: PrivateKeyEntry Certificate chain length: 1 Certificate[1]: Owner: CN=adejuan-desktop.cl.oracle.com, OU=a, O=e, L=i, ST=o, C=U Issuer: CN=adejuan-desktop.cl.oracle.com, OU=a, O=e, L=i, ST=o, C=U Serial number: 4f17459a Valid from: Wed Jan 16 15:42:16CLST 2012 until: Thu Jan 15 15:42:16 CLST 2013 Certificate fingerprints: MD5: 7F:08:FA:DE:CD:D5:C3:D3:83:ED:B8:4F:F2:DA:4E:A1 SHA1: 87:E4:7C:B8:D7:1A:90:53:FE:1B:70:B6:32:22:5B:83:29:81:53:4B Signature algorithm name: SHA256withRSA Version: 3 ******************************************* ******************************************* 6) In some cases, this parameter is needed in the server start up parameters. -Dweblogic.ssl.JSSEEnabled=true Otherwise, enable it from the Server configuration -> SSL -> Use JSSE checkbox.

  Read the article

• Graphics card recommendation for dual-HD output?

  - by Graham

  I'm going for a dual-HD monitor setup (HDMI or DVI output), running Ubuntu 11.10 64-bit with Unity 3D. What graphics card / video card should I get? Requirements: Dual-monitor output for DVI (mixed-resolution: 1920x1080 and 1920x1200) Or dual-HDMI output, if it works with Ubuntu Smooth desktop compositing and (Chrome) browser and IDE window rendering At least 60fps on fullscreen glxgears (1920x1200 resolution) Supported and non-buggy behaviour in Unity 3D/Compiz Not looking to play games Smooth fullscreen video playback (just because)

  Read the article

• Explore the Earth at Night with Google Maps

  - by Jason Fitzpatrick

  Last week we shared a high-resolution video of the Earth at night. Now we’re back with a mashup that combines that same high-resolution data and Google Maps for an interactive look at a human-illuminated Earth. Hit up the link below to take the Google Maps mashup, titled City Lights 2012, for a spin. City Lights 2012 [Google Maps via Mashable] How to Fix a Stuck Pixel on an LCD Monitor How to Factory Reset Your Android Phone or Tablet When It Won’t Boot Our Geek Trivia App for Windows 8 is Now Available Everywhere

  Read the article

• PowerShell Script to Enumerate SharePoint 2010 or 2013 Permissions and Active Directory Group Membership

  - by Brian T. Jackett

  Originally posted on: http://geekswithblogs.net/bjackett/archive/2013/07/01/powershell-script-to-enumerate-sharepoint-2010-or-2013-permissions-and.aspx   In this post I will present a script to enumerate SharePoint 2010 or 2013 permissions across the entire farm down to the site (SPWeb) level.  As a bonus this script also recursively expands the membership of any Active Directory (AD) group including nested groups which you wouldn’t be able to find through the SharePoint UI.   History     Back in 2009 (over 4 years ago now) I published one my most read blog posts about enumerating SharePoint 2007 permissions.  I finally got around to updating that script to remove deprecated APIs, supporting the SharePoint 2010 commandlets, and fixing a few bugs.  There are 2 things that script did that I had to remove due to major architectural or procedural changes in the script. Indenting the XML output Ability to search for a specific user    I plan to add back the ability to search for a specific user but wanted to get this version published first.  As for indenting the XML that could be added but would take some effort.  If there is user demand for it (let me know in the comments or email me using the contact button at top of blog) I’ll move it up in priorities.    As a side note you may also notice that I’m not using the Active Directory commandlets.  This was a conscious decision since not all environments have them available.  Instead I’m relying on the older [ADSI] type accelerator and APIs.  It does add a significant amount of code to the script but it is necessary for compatibility.  Hopefully in a few years if I need to update again I can remove that legacy code.   Solution    Below is the script to enumerate SharePoint 2010 and 2013 permissions down to site level.  You can also download it from my SkyDrive account or my posting on the TechNet Script Center Repository. SkyDrive TechNet Script Center Repository http://gallery.technet.microsoft.com/scriptcenter/Enumerate-SharePoint-2010-35976bdb   001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 ########################################################### #DisplaySPWebApp8.ps1 # #Author: Brian T. Jackett #Last Modified Date: 2013-07-01 # #Traverse the entire web app site by site to display # hierarchy and users with permissions to site. ########################################################### function Expand-ADGroupMembership {     Param     (         [Parameter(Mandatory=$true,                    Position=0)]         [string]         $ADGroupName,         [Parameter(Position=1)]         [string]         $RoleBinding     )     Process     {         $roleBindingText = ""         if(-not [string]::IsNullOrEmpty($RoleBinding))         {             $roleBindingText = " RoleBindings=`"$roleBindings`""         }         Write-Output "<ADGroup Name=`"$($ADGroupName)`"$roleBindingText>"         $domain = $ADGroupName.substring(0, $ADGroupName.IndexOf("\") + 1)         $groupName = $ADGroupName.Remove(0, $ADGroupName.IndexOf("\") + 1)                                     #BEGIN - CODE ADAPTED FROM SCRIPT CENTER SAMPLE CODE REPOSITORY         #http://www.microsoft.com/technet/scriptcenter/scripts/powershell/search/users/srch106.mspx         #GET AD GROUP FROM DIRECTORY SERVICES SEARCH         $strFilter = "(&(objectCategory=Group)(name="+($groupName)+"))"         $objDomain = New-Object System.DirectoryServices.DirectoryEntry         $objSearcher = New-Object System.DirectoryServices.DirectorySearcher         $objSearcher.SearchRoot = $objDomain         $objSearcher.Filter = $strFilter         # specify properties to be returned         $colProplist = ("name","member","objectclass")         foreach ($i in $colPropList)         {             $catcher = $objSearcher.PropertiesToLoad.Add($i)         }         $colResults = $objSearcher.FindAll()         #END - CODE ADAPTED FROM SCRIPT CENTER SAMPLE CODE REPOSITORY         foreach ($objResult in $colResults)         {             if($objResult.Properties["Member"] -ne $null)             {                 foreach ($member in $objResult.Properties["Member"])                 {                     $indMember = [adsi] "LDAP://$member"                     $fullMemberName = $domain + ($indMember.Name)                                         #if($indMember["objectclass"]                         # if child AD group continue down chain                         if(($indMember | Select-Object -ExpandProperty objectclass) -contains "group")                         {                             Expand-ADGroupMembership -ADGroupName $fullMemberName                         }                         elseif(($indMember | Select-Object -ExpandProperty objectclass) -contains "user")                         {                             Write-Output "<ADUser>$fullMemberName</ADUser>"                         }                 }             }         }                 Write-Output "</ADGroup>"     } } #end Expand-ADGroupMembership # main portion of script if((Get-PSSnapin -Name microsoft.sharepoint.powershell) -eq $null) {     Add-PSSnapin Microsoft.SharePoint.PowerShell } $farm = Get-SPFarm Write-Output "<Farm Guid=`"$($farm.Id)`">" $webApps = Get-SPWebApplication foreach($webApp in $webApps) {     Write-Output "<WebApplication URL=`"$($webApp.URL)`" Name=`"$($webApp.Name)`">"     foreach($site in $webApp.Sites)     {         Write-Output "<SiteCollection URL=`"$($site.URL)`">"                 foreach($web in $site.AllWebs)         {             Write-Output "<Site URL=`"$($web.URL)`">"             # if site inherits permissions from parent then stop processing             if($web.HasUniqueRoleAssignments -eq $false)             {                 Write-Output "<!-- Inherits role assignments from parent -->"             }             # else site has unique permissions             else             {                 foreach($assignment in $web.RoleAssignments)                 {                     if(-not [string]::IsNullOrEmpty($assignment.Member.Xml))                     {                         $roleBindings = ($assignment.RoleDefinitionBindings | Select-Object -ExpandProperty name) -join ","                         # check if assignment is SharePoint Group                         if($assignment.Member.XML.StartsWith('<Group') -eq "True")                         {                             Write-Output "<SPGroup Name=`"$($assignment.Member.Name)`" RoleBindings=`"$roleBindings`">"                             foreach($SPGroupMember in $assignment.Member.Users)                             {                                 # if SharePoint group member is an AD Group                                 if($SPGroupMember.IsDomainGroup)                                 {                                     Expand-ADGroupMembership -ADGroupName $SPGroupMember.Name                                 }                                 # else SharePoint group member is an AD User                                 else                                 {                                     # remove claim portion of user login                                     #Write-Output "<ADUser>$($SPGroupMember.UserLogin.Remove(0,$SPGroupMember.UserLogin.IndexOf("|") + 1))</ADUser>"                                     Write-Output "<ADUser>$($SPGroupMember.UserLogin)</ADUser>"                                 }                             }                             Write-Output "</SPGroup>"                         }                         # else an indivdually listed AD group or user                         else                         {                             if($assignment.Member.IsDomainGroup)                             {                                 Expand-ADGroupMembership -ADGroupName $assignment.Member.Name -RoleBinding $roleBindings                             }                             else                             {                                 # remove claim portion of user login                                 #Write-Output "<ADUser>$($assignment.Member.UserLogin.Remove(0,$assignment.Member.UserLogin.IndexOf("|") + 1))</ADUser>"                                                                 Write-Output "<ADUser RoleBindings=`"$roleBindings`">$($assignment.Member.UserLogin)</ADUser>"                             }                         }                     }                 }             }             Write-Output "</Site>"             $web.Dispose()         }         Write-Output "</SiteCollection>"         $site.Dispose()     }     Write-Output "</WebApplication>" } Write-Output "</Farm>"      The output from the script can be sent to an XML which you can then explore using the [XML] type accelerator.  This lets you explore the XML structure however you see fit.  See the screenshot below for an example.      If you do view the XML output through a text editor (Notepad++ for me) notice the format.  Below we see a SharePoint site that has a SharePoint group Demo Members with Edit permissions assigned.  Demo Members has an AD group corp\developers as a member.  corp\developers has a child AD group called corp\DevelopersSub with 1 AD user in that sub group.  As you can see the script recursively expands the AD hierarchy.   Conclusion    It took me 4 years to finally update this script but I‘m happy to get this published.  I was able to fix a number of errors and smooth out some rough edges.  I plan to develop this into a more full fledged tool over the next year with more features and flexibility (copy permissions, search for individual user or group, optional enumerate lists / items, etc.).  If you have any feedback, feature requests, or issues running it please let me know.  Enjoy the script!         -Frog Out

  Read the article

• Using Open MQ as an Oracle CEP Event Source

  - by seth.white

  I helped an Oracle CEP customer recently who wanted to use Open MQ has an event source for their Oracle CEP application.  In this case, the Oracle CEP application was being used to provide monitoring for an electronic commerce website, however, the steps for configuring Open MQ are entirely independent of the application logic. I thought I would list the configuration steps in a blog post in case they might help others in the future. Note that although the Oracle CEP documentation states that only WebLogic and Tibco JMS are "officially" supported, any JMS implementation that provides a Java client should work with Oracle CEP. The first step is to add an adapter to the application's EPN. This can be done in the usual way, using the Eclipse IDE. The end result is something like the following bit of configuration in the application's Spring application context. Note that the provider attribute value of 'jms-inbound' specifies that the out-of-the-box JMS adapter is being used. <wlevs:adapter id="helloworldAdapter" provider="jms-inbound"> </wlevs:adapter>   Next, configure the inbound adapter so that it can connect to Open MQ in the Oracle CEP configuration file (config.xml). The snippet below provides an example of what this configuration should look like. The exact values specified for jndi-provider-url, jndi-factory, connection-jndi-name, destination-jndi-name elements will depend on your Open MQ configuration.  For example , if the name of your Open MQ topic destination is 'ElectronicCommerceTopic', then you would specify that as the destination-jndi-name.  The name of your Open MQ connection factory goes in the connection-jndi-name element. In my simple example, I also specify in event-type element so that the out-of-the-box JMS adapter will attempt to automatically convert incoming messages to events of type HelloWorldEvent. In a more complex application, one would configure a custom converter on the JMS adapter to convert from messages to events.  The Oracle CEP 11.1.3 documentation describes how to do this.   <jms-adapter> <name>helloworldAdapter</name> <event-type>HelloWorldEvent</event-type> <jndi-provider-url>file:///C:/Temp</jndi-provider-url> <jndi-factory>com.sun.jndi.fscontext.RefFSContextFactory</jndi-factory> <connection-jndi-name>YourJMSConnectionFactoryName</connection-jndi-name> <destination-jndi-name>YourJMSDestinationName</destination-jndi-name> </jms-adapter>   Finally, one needs to package the client-side Open MQ jars so that the classes that they contain are available to the Oracle CEP runtime. The recommended way for doing this in the Oracle CEP 11.1.3 release is to package the classes as a library module or simply place them in the application bundle.  The advantage of deploying the classes as a library module is that they are available to any application that wants to connect to Open MQ. In my case, I packaged the classes in my application bundle. A best practice when you want to include additional jars in your application bundle is to create a 'lib' directory in your Eclipse project and then copy the required jars into that directory.  Then, use the support that Eclipse provides to add the jars to the bundle classpath (which makes the classes part of your application in the same way that regular application classes are), and export all of the classes from your application bundle so that they are available to the Oracle CEP server runtime.  The screenshot below Illustrates how this is done in Eclipse.  The bundle classpath contains two Open MQ jars and all packages in the jars are exported.     Finally, import the javax.jms and javax.naming packages into the application module as these are needed by the Open MQ classes. The screenshot below shows the complete list of package imports for my sample application.       Once you have completed these steps, you should be able to build and deploy your application and begin receiving inbound messages from Open MQ. Technorati Tags: CEP,JMS,Adapter,Open MQ,Eclipse .csharpcode { background-color: #ffffff; font-family: consolas, "Courier New", courier, monospace; color: black; font-size: small } .csharpcode pre { background-color: #ffffff; font-family: consolas, "Courier New", courier, monospace; color: black; font-size: small } .csharpcode pre { margin: 0em } .csharpcode .rem { color: #008000 } .csharpcode .kwrd { color: #0000ff } .csharpcode .str { color: #006080 } .csharpcode .op { color: #0000c0 } .csharpcode .preproc { color: #cc6633 } .csharpcode .asp { background-color: #ffff00 } .csharpcode .html { color: #800000 } .csharpcode .attr { color: #ff0000 } .csharpcode .alt { background-color: #f4f4f4; margin: 0em; width: 100% } .csharpcode .lnum { color: #606060 } .csharpcode { background-color: #ffffff; font-family: consolas, "Courier New", courier, monospace; color: black; font-size: small } .csharpcode pre { background-color: #ffffff; font-family: consolas, "Courier New", courier, monospace; color: black; font-size: small } .csharpcode pre { margin: 0em } .csharpcode .rem { color: #008000 } .csharpcode .kwrd { color: #0000ff } .csharpcode .str { color: #006080 } .csharpcode .op { color: #0000c0 } .csharpcode .preproc { color: #cc6633 } .csharpcode .asp { background-color: #ffff00 } .csharpcode .html { color: #800000 } .csharpcode .attr { color: #ff0000 } .csharpcode .alt { background-color: #f4f4f4; margin: 0em; width: 100% } .csharpcode .lnum { color: #606060 } .csharpcode { background-color: #ffffff; font-family: consolas, "Courier New", courier, monospace; color: black; font-size: small } .csharpcode pre { background-color: #ffffff; font-family: consolas, "Courier New", courier, monospace; color: black; font-size: small } .csharpcode pre { margin: 0em } .csharpcode .rem { color: #008000 } .csharpcode .kwrd { color: #0000ff } .csharpcode .str { color: #006080 } .csharpcode .op { color: #0000c0 } .csharpcode .preproc { color: #cc6633 } .csharpcode .asp { background-color: #ffff00 } .csharpcode .html { color: #800000 } .csharpcode .attr { color: #ff0000 } .csharpcode .alt { background-color: #f4f4f4; margin: 0em; width: 100% } .csharpcode .lnum { color: #606060 }

  Read the article

• Easy Profiling Point Insertion

  - by Geertjan

  One really excellent feature of NetBeans IDE is its Profiler. What's especially cool is that you can analyze code fragments, that is, you can right-click in a Java file and then choose Profiling | Insert Profiling Point. When you do that, you're able to analyze code fragments, i.e., from one statement to another statement, e.g., how long a particular piece of code takes to execute: https://netbeans.org/kb/docs/java/profiler-profilingpoints.html However, right-clicking a Java file and then going all the way down a longish list of menu items, to find "Profiling", and then "Insert Profiling Point" is a lot less easy than right-clicking in the sidebar (known as the glyphgutter) and then setting a profiling point in exactly the same way as a breakpoint: That's much easier and more intuitive and makes it far more likely that I'll use the Profiler at all. Once profiling points have been set then, as always, another menu item is added for managing the profiling point: To achieve this, I added the following to the "layer.xml" file: <folder name="Editors"> <folder name="AnnotationTypes"> <file name="profiler.xml" url="profiler.xml"/> <folder name="ProfilerActions"> <file name="org-netbeans-modules-profiler-ppoints-ui-InsertProfilingPointAction.shadow"> <attr name="originalFile" stringvalue="Actions/Profile/org-netbeans-modules-profiler-ppoints-ui-InsertProfilingPointAction.instance"/> <attr name="position" intvalue="300"/> </file> </folder> </folder> </folder> Notice that a "profiler.xml" file is referred to in the above, in the same location as where the "layer.xml" file is found. Here is the content: <!DOCTYPE type PUBLIC '-//NetBeans//DTD annotation type 1.1//EN' 'http://www.netbeans.org/dtds/annotation-type-1_1.dtd'> <type name='editor-profiler' description_key='HINT_PROFILER' localizing_bundle='org.netbeans.eppi.Bundle' visible='true' type='line' actions='ProfilerActions' severity='ok' browseable='false'/> Only disadvantage is that this registers the profiling point insertion in the glyphgutter for all file types. But that's true for the debugger too, i.e., there's no MIME type specific glyphgutter, instead, it is shared by all MIME types. Little bit confusing that the profiler point insertion can now, in theory, be set for all MIME types, but that's also true for the debugger, even though it doesn't apply to all MIME types. That probably explains why the profiling point insertion can only be done, officially, from the right-click popup menu of Java files, i.e., the developers wanted to avoid confusion and make it available to Java files only. However, I think that, since I'm already aware that I can't set the Java debugger in an HTML file, I'm also aware that the Java profiler can't be set that way as well. If you find this useful too, you can download and install the NBM from here: http://plugins.netbeans.org/plugin/55002

  Read the article

• How to make scripts run in Guake terminal instead of normal terminal

  - by Nirmik

  I have installed Guake terminal and I find it amazing. I have many scripts added as .desktop files in launcher. Now I want these scripts to run in the Guake terminal instead of opening in the normal Gnome terminal. How can I achieve this? Thanx :) Edit- The .desktop file is such- [Desktop Entry] Type=Application Terminal=true Icon=/path/to/icon/icon.svg Name=app-name Exec=/path/to/file/mount-unmount.sh Name=app-name

  Read the article

• SCCM 2007 Collections per OU

  - by VirtualizeIT

  Recently I wanted to create our SCCM collections setup as our Active Directory structure. I finally figured out how to create collections per OU of the domain. I decided to create a simple tutorial that may help other IT professionals the steps to complete this task.   1. Open the ConfigMgr and navigation to the collections. To navigate to the collections go to Site Database>Computer Management>Collections. 2. In the ‘Collections’ right-click and select New Collections. Then it will pop up a Wizards so you can enter the name of the collection and any notes that you may want to add that is associated with the collection.                       3. Next, select the database icon. In the ‘Name’ textbox enter the name of the query. I named mine ‘Query’ just for simplicity sake. After you enter the name select ‘Edit Query Statement…’ 4. Select the ‘Criteria’ tab 5. Select the icon that looks like a sun. 6. At this point you should see a dialog box like this…                     7. Next, click the ‘select’ button. 8. Under the ‘Attribute class’ scroll through until you see ’System Resource’ and for the ‘Attribute"’ scroll through you see ‘System OU Name’. It should look something like this…                 9. After that select OK. 10. In the ‘Value’ textbox enter the string that is associated with the OU in your domain. NOTE: If you don’t know your string name for your OU you can simply go to “Active Directory Users and Computers” and right-click on the OU and select properties. In the ‘object’ tab you should see the string under the ‘Canonical name of object”. That is the string that you put in the ‘Value’ text box. 11. After you enter the OU string name press OK>OK>OK>NEXT>NEXT>FINISH.   That’s it!   I hope this tutorial has help you understand how to create a collection through your OU structure.

  Read the article

• set several menuitems.visible=true (7 replies)

  Hi all,i got menu like this Master Transaksi Karyawan name : mnuKaryawan Penjualan name : mnuJual User name : mnuUser Logout Exit I'm trying to show the mnuKaryawan etc based on user rights... I use database to store the menu name,and the table like this position menu admin mnuKaryawan admin mnuUser user mnuJual How to set the mnuKaryawan etc.visible true ? Thanks a lot....

  Read the article

• Force gdm login screen to the primary monitor

  - by Kirill

  I have two monitors attached to my video card. Primary monitor has a resolution equal to 1280x1024 and the second has 1920x1200. My gdm login screen always appears on the second monitor even if it is switched off. My question is how to force gdm to show the login screen always on the primary monitor with resolution 1280x1024? I use Nvidia GT9500 videcard in Twinview mode. I can't use Xinerama because vpdau doesn't work correclty in this mode.

  Read the article

• Execution plan warnings–The final chapter

  - by Dave Ballantyne

  In my previous posts (here and here), I showed examples of some of the execution plan warnings that have been added to SQL Server 2012.  There is one other warning that is of interest to me : “Unmatched Indexes”. Firstly, how do I know this is the final one ?  The plan is an XML document, right ? So that means that it can have an accompanying XSD.  As an XSD is a schema definition, we can poke around inside it to find interesting things that *could* be in the final XML file. The showplan schema is stored in the folder Microsoft SQL Server\110\Tools\Binn\schemas\sqlserver\2004\07\showplan and by comparing schemas over releases you can get a really good idea of any new functionality that has been added. Here is the section of the Sql Server 2012 showplan schema that has been interesting me so far : <xsd:complexType name="AffectingConvertWarningType"> <xsd:annotation> <xsd:documentation>Warning information for plan-affecting type conversion</xsd:documentation> </xsd:annotation> <xsd:sequence> <!-- Additional information may go here when available --> </xsd:sequence> <xsd:attribute name="ConvertIssue" use="required"> <xsd:simpleType> <xsd:restriction base="xsd:string"> <xsd:enumeration value="Cardinality Estimate" /> <xsd:enumeration value="Seek Plan" /> <!-- to be extended here --> </xsd:restriction> </xsd:simpleType> </xsd:attribute> <xsd:attribute name="Expression" type ="xsd:string" use="required" /></xsd:complexType><xsd:complexType name="WarningsType"> <xsd:annotation> <xsd:documentation>List of all possible iterator or query specific warnings (e.g. hash spilling, no join predicate)</xsd:documentation> </xsd:annotation> <xsd:choice minOccurs="1" maxOccurs="unbounded"> <xsd:element name="ColumnsWithNoStatistics" type="shp:ColumnReferenceListType" minOccurs="0" maxOccurs="1" /> <xsd:element name="SpillToTempDb" type="shp:SpillToTempDbType" minOccurs="0" maxOccurs="unbounded" /> <xsd:element name="Wait" type="shp:WaitWarningType" minOccurs="0" maxOccurs="unbounded" /> <xsd:element name="PlanAffectingConvert" type="shp:AffectingConvertWarningType" minOccurs="0" maxOccurs="unbounded" /> </xsd:choice> <xsd:attribute name="NoJoinPredicate" type="xsd:boolean" use="optional" /> <xsd:attribute name="SpatialGuess" type="xsd:boolean" use="optional" /> <xsd:attribute name="UnmatchedIndexes" type="xsd:boolean" use="optional" /> <xsd:attribute name="FullUpdateForOnlineIndexBuild" type="xsd:boolean" use="optional" /></xsd:complexType> I especially like the “to be extended here” comment,  high hopes that we will see more of these in the future.   So “Unmatched Indexes” was a warning that I couldn’t get and many thanks must go to Fabiano Amorim (b|t) for showing me the way.   Filtered indexes were introduced in Sql Server 2008 and are really useful if you only need to index only a portion of the data within a table.  However,  if your SQL code uses a variable as a predicate on the filtered data that matches the filtered condition, then the filtered index cannot be used as, naturally,  the value in the variable may ( and probably will ) change and therefore will need to read data outside the index.  As an aside,  you could use option(recompile) here , in which case the optimizer will build a plan specific to the variable values and use the filtered index,  but that can bring about other problems.   To demonstrate this warning, we need to generate some test data :   DROP TABLE #TestTab1GOCREATE TABLE #TestTab1 (Col1 Int not null, Col2 Char(7500) not null, Quantity Int not null)GOINSERT INTO #TestTab1 VALUES (1,1,1),(1,2,5),(1,2,10),(1,3,20), (2,1,101),(2,2,105),(2,2,110),(2,3,120)GO and then add a filtered index CREATE INDEX ixFilter ON #TestTab1 (Col1)WHERE Quantity = 122 Now if we execute SELECT COUNT(*) FROM #TestTab1 WHERE Quantity = 122 We will see the filtered index being scanned But if we parameterize the query DECLARE @i INT = 122SELECT COUNT(*) FROM #TestTab1 WHERE Quantity = @i The plan is very different a table scan, as the value of the variable used in the predicate can change at run time, and also we see the familiar warning triangle. If we now look at the properties pane, we will see two pieces of information “Warnings” and “UnmatchedIndexes”. So, handily, we are being told which filtered index is not being used due to parameterization.

  Read the article

• When a problem is resolved

  - by Rob Farley

  This month’s T-SQL Tuesday is hosted by Jen McCown, and she’s picked the topic of Resolutions. It’s a new year, and she’s thinking about what people have resolved to do this year. Unfortunately, I’ve never really done resolutions like that. I see too many people resolve to quit smoking, or lose weight, or whatever, and fail miserably. I’m not saying I don’t set goals, but it’s not a thing for New Year. The obvious joke is “1920x1080” as a resolution, but I’m not going there. I think Resolving is a strange word. It makes it sound like I’m having to solve a problem a second time, when actually, it’s more along the lines of solving a problem well enough for it to count as finished. If something has been resolved, a solution has been provided. There is a resolution, through the provision of a solution. It’s a strangeness of English. When I look up the word resolution at dictionary.com, it has 12 options, including “settling of a problem”. There’s a finality about resolution. If you resolve to do something, you’re saying “Yes. This is a done thing. I’m resolving to do it, which means that it may as well be complete already.” I like to think I resolve problems, rather than just solving them. I want my solving to be final and complete. If I tune a query, I don’t want to find that I’m back in there, re-tuning it at some point. Strangely, if I re-solve a problem, that implies that I didn’t resolve it in the first place. I only solved it. Temporarily. We “data-folk” live in a world where the most common answer is “It depends.” Frustratingly, the thing an answer depends on may still be changing in the system in question. That probably means that any solution that is put in place may need reinvestigating at some point later. So do I resolve things? Yes. Am I Chuck Norris, and solve things so well the world would break first? No. Do these two claims happily sit beside each other? No, unfortunately not. But I happily take responsibility for things, and let my clients depend on me to see it through. As far as they are concerned, it is resolved. And so I resolve to keep resolving, right through 2011.

  Read the article

• unknown monitor problem

  - by dev

  I'm using HCL P30 laptop with 1280x800 60 Hz default resolution.But none of the ubuntu versions are capable of detecting my monitor.In 11.04 the resolution is 1024x768 61 Hz. When I run xrandr command in terminal,it returns xrandr: Failed to get size of gamma for output default Screen 0: minimum 640 x 480, current 1024 x 768, maximum 1024 x 768 default connected 1024x768+0+0 0mm x 0mm 1024x768 61.0* 800x600 61.0 640x480 60.0 So,how can I set it to 1280x800 60 Hz. plz reply soon. thnx in advance.

  Read the article

• Enabling EUS support in OUD 11gR2 using command line interface

  - by Sylvain Duloutre

  Enterprise User Security (EUS) allows Oracle Database to use users & roles stored in LDAP for authentication and authorization.Since the 11gR2 release, OUD natively supports EUS. EUS can be easily configured during OUD setup. ODSM (the graphical admin console) can also be used to enable EUS for a new suffix. However, enabling EUS for a new suffix using command line interface is currently not documented, so here is the procedure: Let's assume that EUS support was enabled during initial setup.Let's o=example be the new suffix I want to use to store Enterprise users. The following sequence of command must be applied for each new suffix: // Create a local database holding EUS context infodsconfig create-workflow-element --set base-dn:cn=OracleContext,o=example --set enabled:true --type db-local-backend --element-name exampleContext -n // Add a workflow element in the call path to generate on the fly attributes required by EUSdsconfig create-workflow-element --set enabled:true --type eus-context --element-name eusContext --set next-workflow-element:exampleContext -n // Add the context to a workflow for routingdsconfig create-workflow --set base-dn:cn=OracleContext,o=example --set enabled:true --set workflow-element:eusContext --workflow-name exampleContext_workflow -n //Add the new workflow to the appropriate network groupdsconfig set-network-group-prop --group-name network-group --add workflow:exampleContext_workflow -n // Create the local database for o=exampledsconfig create-workflow-element --set base-dn:o=example --set enabled:true --type db-local-backend --element-name example -n // Create a workflow element in the call path to the user data to generate on the fly attributes expected by EUS dsconfig create-workflow-element --set enabled:true --set eus-realm:o=example --set next-workflow-element:example --type eus --element-name eusWfe// Add the db to a workflow for routingdsconfig create-workflow --set base-dn:o=example --set enabled:true --set workflow-element:eusWfe --workflow-name example_workflow -n //Add the new workflow to the appropriate network groupdsconfig set-network-group-prop --group-name network-group --add workflow:example_workflow -n  // Add the appropriate acis for EUSdsconfig set-access-control-handler-prop \           --add global-aci:'(target="ldap:///o=example")(targetattr="authpassword")(version 3.0; acl "EUS reads authpassword"; allow (read,search,compare) userdn="ldap:///??sub?(&(objectclass=orclservice)(objectclass=orcldbserver))";)' dsconfig set-access-control-handler-prop \       --add global-aci:'(target="ldap:///o=example")(targetattr="orclaccountstatusevent")(version 3.0; acl "EUS writes orclaccountstatusenabled"; allow (write) userdn="ldap:///??sub?(&(objectclass=orclservice)(objectclass=orcldbserver))";)' Last but not least you must adapt the content of the ${OUD}/config/EUS/eusData.ldif  file with your suffix value then inport it into OUD.

  Read the article

• Mutable Records in F#

  - by MarkPearl

  I’m loving my expert F# book – today I thought I would give a post on using mutable records as covered in Chapter 4 of Expert F#. So as they explain the simplest mutable data structures in F# are mutable records. The whole concept of things by default being immutable is a new one for me from my C# background. Anyhow… lets look at some C# code first. using System; using System.Collections.Generic; using System.Linq; using System.Text; namespace MutableRecords { public class DiscreteEventCounter { public int Total { get; set; } public int Positive { get; set; } public string Name { get; private set; } public DiscreteEventCounter(string name) { Name = name; } } class Program { private static void recordEvent(DiscreteEventCounter s, bool isPositive) { s.Total += 1; if (isPositive) s.Positive += 1; } private static void reportStatus (DiscreteEventCounter s) { Console.WriteLine("We have {0} {1} out of {2}", s.Positive, s.Name, s.Total); } static void Main(string[] args) { var longCounter = new DiscreteEventCounter("My Discrete Counter"); recordEvent(longCounter, true); recordEvent(longCounter, true); reportStatus(longCounter); Console.ReadLine(); } } } Quite simple, we have a class that has a few values. We instantiate an instance of the class and perform increments etc on the instance. Now lets look at an equivalent F# sample. namespace EncapsulationNS module Module1 = open System type DiscreteEventCounter = { mutable Total : int mutable Positive : int Name : string } let recordEvent (s: DiscreteEventCounter) isPositive = s.Total <- s.Total+1 if isPositive then s.Positive <- s.Positive+1 let reportStatus (s: DiscreteEventCounter) = printfn "We have %d %s out of %d" s.Positive s.Name s.Total let newCounter nm = { Total = 0; Positive = 0; Name = nm } // // Using it... // let longCounter = newCounter "My Discrete Counter" recordEvent longCounter (true) recordEvent longCounter (true) reportStatus longCounter System.Console.ReadLine() Notice in the type declaration of the DiscreteEventCounter we had to explicitly declare that the total and positive value holders were mutable. And that’s it – a very simple example of mutable types.

  Read the article

• Should SQL Server tools target wide screen formats instead of portrait formats?

  - by Greg Low

  There was a short discussion on the SQL Down Under mailing list this morning about screen resolutions for working with the SQL Server tools. In particular, the issue was about how unusable the tools are on the 1366x768 resolution notebooks that now seem to be the most common. While finding a notebook with an appropriate resolution is obviously the answer at this time, I started thinking that the product itself needs to address this. SQL Server tools currently target a portrait 4:3 shape for minimum...(read more)

  Read the article

• how to call web method in java application?.

  - by user12344

  Hi, I have created java web application(Web Service). I want to call the setName() method in java application(GUI). how is call web method in application?. package sv; import javax.jws.WebMethod; import javax.jws.WebParam; import javax.jws.WebService; @WebService() public class MyService { @WebMethod(operationName = "setName") public String setName(@WebParam(name = "name") String name) { return "my string is "+ name; } }

  Read the article

< Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >