Search Results

Search found 5789 results on 232 pages for 'tuner card'.

Page 209/232 | < Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >

• Computer making strange sound when turned on, ever since power outage

  - by Dot NET

  Recently we experienced a power outage, and the PC was off. However, once the power came back, I switched on the PC and heard a strange noise - almost as if the hard disk or fans were struggling to work. I can't really describe the sound, but it's a laboured, loud sound almost like a jack-hammer. This has been persisting ever since the power outage, however the noise stops after around 10 minutes or so, and doesn't start again until the computer is turned off and on again. At first I thought it had something to do with the HDD, but all my files are intact, chkdsk did not report any issues and performance is 100% unchanged, even in games (so the gfx card is fine, and so is the HDD most likely). My PC setup basically has around 3 cooling fans, but I'm not sure if it's one of these either as the noise actually stops after 10 minutes or so, and if I leave the PC on for 4 hours (for example) the noise never starts again. It's there solely when turning on the PC. I haven't got a UPS, and it's important to note that the computer was not on when the power went out - it was merely plugged in. I then promptly unplugged the PC once the power was out, and only plugged it in again when the power came back. Could it be the power supply? Unfortunately I can't open my tower as I would void the warranty. Are there any tests which I could carry out without voiding the warranty?

  Read the article

• Dns - wildcard vs. cname subdomains

  - by Matthew

  Alright I have to admit I'm confused with how DNS works. I've always just added things until they worked, and now it's time to learn how they work. So one confusing thing to me is that there's sort of two places I can have records. I have an account with rackspace cloud servers. And then there's the place I registered the domain. But both allow me to edit DNS records. Should I do everything at both places or is one better than the other or am I missing the point? Subdomains confuse me too. I'd like to be able to just have a wildcard subdomain (I've done this in the past.) I just don't like the idea of adding a cname record or A record every time I need a new subdomain. Then I read this and it says: The exact rules for when a wild card will match are specified in RFC 1034, but the rules are neither intuitive nor clearly specified. This has resulted in incompatible implementations and unexpected results when they are used.

  Read the article

• DVI output only working on Windows, not during booting or on Linux

  - by Mononofu

  So yesterday I booted my laptop up and the external monitor I have it connected to just stayed black. At first, I thought the problem would go away when Ubuntu was loaded, but it didn't. I tried to reboot a few times, to no avail. Then I decided to give Windows 7 a try, and suddenly (at the login-screen), my external monitor turned on and worked like normal. I have connected the monitor via DVI, and this only seems to work with Windows now. I don't even get a signal in my BIOS! Mind you, everything was working fine before that, and I didn't change a single thing. I then tried to connect the monitor via VGA (from my DVI jack, which can output VGA using an adaptor), and it worked again. However, 1920x1200 using VGA looks like crap - black print on white background is basically illegible. Do you have any ideas how to fix this peculiar problem? I only use windows for gaming, so it's no real help that it still works normally. Please also excuse any spelling mistakes, I am practically typing this blindly. Edit: I only have one graphics card in my laptop, and I can't select anything related to that in my BIOS. In fact, I can pretty much do almost nothing there. My laptop is a Nexoc Osiris E703, graphics gard is a GeForce Go 7900 GTX. As I mentioned before, DVI output during booting and on Ubuntu was working fine for years before yesterday!

  Read the article

• how is the the linux console displayed to the user and how does the user go about changing the conso

  - by Chris

  I've been searching for the last two day on trying to understand how the console displays itself to the user and how to change the console settings. I've had some luck along the way but nothing that I've found has giving me a real clear explanation of how the console is displayed or how to change or control it's display settings. Some examples that of what I'm looking for are as follows: How is the console displayed on the screen? I know with X11 it uses your graphics card driver to display graphics to the screen, but how is the consoles text mode handled? Could some one ether explain this to me or point me to an in-depth overview of it all? Is it possible to have multi-head support in console mode with separate tty's on each screen? If so how would I go about setting this up? How would you go about changing the size of the console display from the default 80x25 to a custom size? I'm testing anything I find on a debian testing build, which is just the minimal base install on a virtual box. In time I will be using this information to setup my main system which is multi-head with 3 monitors. I would like to be able to support all three displays in console mode if possible.

  Read the article

• DVI output _only_ working on Windows, not during booting or on Linux

  - by Mononofu

  So yesterday I booted my laptop up and the external monitor I have it connected to just stayed black. At first, I thought the problem would go away when Ubuntu was loaded, but it didn't. I tried to reboot a few times, to no avail. Then I decided to give Windows 7 a try, and suddenly (at the login-screen), my external monitor turned on and worked like normal. I have connected the monitor via DVI, and this only seems to work with Windows now. I don't even get a signal in my BIOS! Mind you, everything was working fine before that, and I didn't change a single thing. I then tried to connect the monitor via VGA (from my DVI jack, which can output VGA using an adaptor), and it worked again. However, 1920x1200 using VGA looks like crap - black print on white background is basically illegible. Do you have any ideas how to fix this peculiar problem? I only use windows for gaming, so it's no real help that it still works normally. Please also excuse any spelling mistakes, I am practically typing this blindly. Edit: I only have one graphics card in my laptop, and I can't select anything related to that in my BIOS. In fact, I can pretty much do almost nothing there. My laptop is a Nexoc Osiris E703, graphics gard is a GeForce Go 7900 GTX. As I mentioned before, DVI output during booting and on Ubuntu was working fine for years before yesterday!

  Read the article

• System With Two Network Adapters

  - by Synetech inc.

  Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

  Read the article

• Bypass network stack. Which options do we have? Pros and cons of each option [on hold]

  - by javapowered

  I'm writing trading application. I want to bypass network stack in Linux but I don't know how this can be done. I'm looking for complete list of options with pros and cons of each of them. The only option I know - is to buy solarflare network card which supports OpenOnLoad. What other options should I consider and what is pros and cons of each of them? Well the question is pretty simple - what is the best way to bypass network stack? upd: OpenOnload It achieves performance improvements in part by performing network processing at user-level, bypassing the OS kernel entirely on the data path. Intel DDIO to allow Intel® Ethernet Controllers and adapters to talk directly with the processor cache of the Intel® Xeon® processor E5. What's key difference between these techologies? Do they do roughly the same things? I much better like Intel DDIO because it's much easy to use, but OpenOnload required a lot of installation and tuning. If good OpenOnload application is much faster than good Intel DDIO application?

  Read the article

• Magical moving desktop icons

  - by Nathan Taylor

  I have encountered a very strange behavior in Windows 7 that I cannot seem to identify and I have never seen or heard of on any system configuration. Whenever I move my mouse to the left-most edge of my primary display (centered in 3-display setup), my desktop icons magically move away from the cursor (up or down and to the right). It only happens when my desktop has focus and the mouse is positioned on the left, top or bottom edge of the main display. Moving the mouse all the way to the right edge of my right secondary display causes the mouse icons to snap back into their correct position. Ridiculous video of the issue My setup is 3 displays on two display adapters. The main display is running at 2560x1600, connected to the machine via a USB-powered DVI-D to DisplayPort adapter and is driven by an NVIDIA NVS 3100M video card. The secondary displays are running at 1440x900 and 1200x1920 and are driven by integrated Intel HD Graphics (mobile). It seems like some kind of panning behavior, but it's obviously not working as expected. I have updated all of my drivers, but no change. It's probably worth noting that the desktop icons are set to auto-arrange.

  Read the article

• How do I tell Windows to use 802.11 in preference to 3G?

  - by Jon Skeet

  I have a Samsung NC-10 netbook which I take to work every day. Most of the time I use it just on the train/bus, but I also use it at work and home. It has a built-in 3G card which I want to use when travelling, but I'd prefer to use wifi when I'm at work or home, for obvious reasons. Unfortunately, if the 3G connection is up, Windows appears to use that in preference to wifi. Starting up and shutting down the 3G modem is a bit of a pain - it's not hard as such, just a bit inconvenient. Ideally I'd like it to always be up, and even have the connection itself up all the time, but without routing traffic through it if there's a wifi connection up. This is what my Android phone does, for example. Is there somewhere in Windows which lets me express an ordering for network interfaces? I suspect the routing table may be relevant, but it's a bit of a pain to mess around with. I'd really expect there to be a simple GUI way of setting this up - after all, it would equally be useful when dealing with wired vs wifi connections. I'm currently using Windows XP Home, but Windows 7 answers would also be useful as I'll be migrating soon.

  Read the article

• lenovo x1 carbon windows 8 frequent wifi disconnect issue

  - by hIpPy

  I'm having frequent wifi disconnects on my Lenovo X1 Carbon Touch laptop. I got this laptop 2 months back and it has been happening ever since about 3-5 times a day and 10 times a week on average. I've Frontier Fios internet. Power connected or not does not matter. Once I get disconnected, I try below to connect again in that order: turn Airplane mode on and off, troubleshoot network problems windows troubleshooter), restart the laptop I'd find that the WiFi adapter would get disabled and sometimes windows troubleshooting would help but more than often I'd end up restarting the laptop. A week back, I upgraded my wifi network adapter drivers (now Intel, version 15.5.6.48, 10/3/2012). I still get disconnected frequently but turning Airplane mode on and off gets me connected again. So the driver update did help. Windows 8 is updated. None of the other devices (nexus, iphone phones, nexus7, ipad tablets) would have wifi issues when my laptop would get disconnected. config: Intel(R) Centrino(R) Advanced-N 6205 (WiFi network adapter) Microsoft Windows 8 Pro Microsoft Windows [Version 6.2.9200] x64-based PC LENOVO System Model: 3443CTO X1 Carbon Touch I recently noticed this log message When I got disconnected in event viewer: Your computer was not assigned an address from the network (by the DHCP Server) for the Network Card with network address 0x[XXXXXXXXXXXX]. The following error occurred: 0x79. Your computer will continue to try and obtain an address on its own from the network address (DHCP) server. Any idea?

  Read the article

• Win7 Hangs During App Install/Upgrade/Uninstall

  - by JadeMason

  I have a custom built PC that intermittently hangs when installing, uninstalling, or upgrading applications. Technical Specs ASUS P5E w/ WiFi Motherboard Intel Core2 Quad Q6600 Processor 4x 2GB G.Skill DDR2 800 SDRAM ASUS EAH2900XT / Radeon HD 2900XT 512MB Video Card Under normal operation the machine runs reliably, even under heavy load, such as video transcoding. The temperature never gets anywhere near where I would worry about it. However, the machine regularly hangs (complete lockup, no response to keyboard or mouse, no activity on-screen) when either installing a new application, uninstalling an existing application, or applying patches to existing applications or the OS. This is extremely frustrating as this machine is primarily used as a HTPC. Several apps are configured for automatic updates, and these updates sometimes cause the machine to lockup while we are watching content on the PC. In previously investigating this issue, I found one likely problem could be my Logitech Webcam. The Logitech software has a bug that leaves an entry in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\ Control\SessionManager\PendingFileRenameOperations Which references the Temp directory. My registry contained this error, so I uninstalled the webcam software and deleted this registry key value. Unfortunately, the machine will still intermittently hang. I've noticed that the hangs always happen when an install/upgrade/uninstall requires elevated privileges (presumably to modify the registry). I can typically get at least one install/upgrade/uninstall to complete after a reboot, but after that it is a game of russian roulette to see if the operation will succeed or hang the machine. The event log is not helpful, as log messages end at the time of the hang, with no record of a warning or error. My only recourse when the machine hangs in this way is to perform a hard reset/power cycle. Any tips on how to further debug this issue are greatly appreciated.

  Read the article

• Basic connectivity issues between Win 7 and XP mixed wired/wireless network. [Solved]

  - by Pulse

  Setup: Windows 7 x64 Ultimate desktop hard wired to Asus WL500gp router (WL500gpv2-1.9.2.7-d-r1445 firmware) Several Bridged VirtualBox VM's running XP, 7, ubuntu server 10.04, Mint 9 and SuSE 11.2 Win XP Pro SP3 notebook with D-Link Airplus wireless network card. No firewall or other security software currently running on either platform (at least for the duration of the test) Situation: Router is acting DHCP server Clients are receiving correct addresses and additional parameters Internet connectivity is available from all clients Windows 7 sharing is set to Network type = work (not home group) NetBT is disabled on all clients using smb over TCP What I can do: I can ping the router and internet addresses from the wireless XP notebook I can ping the Win 7 desktop and any VM from the XP wireless notebook I can ping all devices from the router All VM's and 7 can ping each other and the router as well as Internet addresses What I can't do: I cannot ping the XP wireless notebook from either the Win 7 desktop or the VM's; it always returns a destination host unreachable error. Tracert resolves the name or the XP notebook but also returns a destination host unreachable. From the above it would seem that something is blocking connectivity in a single direction (from the Win 7 box to the Win XP notebook) only but the router can ping the XP notebook. Some fresh input would be most welcome, as this is beginning to drive me batty. Thanks

  Read the article

• Ubuntu Server Wireless connection issue - replaced router but kept ESSID

  - by Stevo

  I have a ubuntu server 12.04 which was connected to my wireless network with no problem I replaced the wireless router but kept the ESSID and password the same. All other devices on network have connected correctly. However the Ubuntu Server will not route correctly. It will connect to the wifi router, and get a dhcp served IP address, however it will not route anything. I cannot ping the router from the server. the contents of /etc/resolve.conf are updated with the information from the router, (the host name has been served) I know there is nothing wrong with the router or the server, or the wireless card etc. I'm assuming there's some cached setting that associates the old router with the ESSID and causing the issue. I've got a lot of other devices connected to the router, so don't want to change the name of the ESSID. How do I fix this? EDIT: outputs (abbreviated as I've got no cut and paste) netstat -rn: Kernel IP Routing table Dest Gate Gen Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0. UG 0 0 0 wlan0 192.168.0.0 0.0.0.0. 255.255.255.0 U 0 0 0 wlan0

  Read the article

• How can I take browser screenshots at a higher resolution than my browser supports?

  - by user53575

  I need to take a screenshot of a website as it would appear on a very high resolution monitor... say 16000x12800 pixels. My laptop's screen has a native resolution of 1280x800. Basically, I need to simulate having a monitor resolution much higher than my monitor and video card actually supports. I want the screenshot of the site to look pretty much how it does when you hit CTRL MINUS (zoom out) in Firefox repeatedly, but without any loss of pixels due to scaling. How can I do this? Is there some way to use virtual machine software to simulate a super-high-res display? If not, is there some way to open a browser window bigger than the screen, and then capture its contents as a PNG somehow? Anything else that might work? Here was an answer: http://superuser.com/questions/120266/how-can-i-take-browser-screenshots-at-a-higher-resolution-than-my-browser-support But it doesn't work. Firefox remains in the resolution of the physical screen. The window blinks and shrinks back to normal resolution. Please Help!!

  Read the article

• TCP dies on a Linux laptop

  - by Roman Cheplyaka

  Once in several days I have the following problem. My laptop (Debian GNU/Linux testing) suddenly becomes unable to work with TCP connections to the internet. The following things continue to work fine: UDP (DNS), ICMP (ping) — I get instant response TCP connections to other machines in the local network (e.g. I can ssh to a neighbour laptop) everything is ok for other machines in my LAN But when I try TCP connections from my laptop, they time out (no response to SYN packets). Here's a typical curl output: % curl -v google.com * About to connect() to google.com port 80 (#0) * Trying 173.194.39.105... * Connection timed out * Trying 173.194.39.110... * Connection timed out * Trying 173.194.39.97... * Connection timed out * Trying 173.194.39.102... * Timeout * Trying 173.194.39.98... * Timeout * Trying 173.194.39.96... * Timeout * Trying 173.194.39.103... * Timeout * Trying 173.194.39.99... * Timeout * Trying 173.194.39.101... * Timeout * Trying 173.194.39.104... * Timeout * Trying 173.194.39.100... * Timeout * Trying 2a00:1450:400d:803::1009... * Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable * Success * couldn't connect to host * Closing connection #0 curl: (7) Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable Restarting the connection and/or reloading the network card kernel module doesn't help. The only thing that helps is reboot. Clearly something is wrong with my system (everything else works fine), but I have no idea what exactly. I don't know how to reproduce this, but as I said, it happens every several days. My setup is a wireless router that is connected to the ISP via PPPoE. Any advice?

  Read the article

• Latitude D600 USB port problem

  - by Moab

  Both USB ports stopped communicating on my D600, they have power, my optical mouse still lights up, no device works on the ports, everything is fine in Device manager in Dual boot XP and W7. Checked the bios, not much in there for USB. No usb device shows up when I use the F12 boot device menu either, so it must be some hardware issue. I have another hard drive with Ubuntu on it, popped it in and USB does not communicate with it either. Appears to have 5v but no communication, any Ideas besides another motherboard or USB card for the pcmcia slot (these don't work to well from my research)? I mostly use them for mass storage devices and pcmcia slots don't supply enough power for these devices. Thanks to all who answer with last ditch efforts. I hate to give up on it, its been good to me and still runs rather well for its vintage. EDIT: I did inspect the ports with a flashlight and did a partial disassembly of the laptop in an attempt to check the solder joints, but would require complete motherboard removal to see them, that is where I stopped. .

  Read the article

• Troubleshooting my internet connection

  - by Simon Verbeke

  While I was out of the house, my father rearranged the network cables a bit. I don't know what he has done exactly - He says nothing more then pulling and untangling. When I came back home, my internet connection changed its IP from 192.168.0.205 to 169.254.197.233. The speed changed from 1Gbps to 10Mbps. It has also been at 100Mbps for a while. My subnetmask changed from 255.255.255.0 to 255.255.0.0. The standard gateway changed from 192.168.0.1 to no standard gateway. My DNS servers remain the same. I have checked the lights of the UTP ports, and it looks like it's only sending a heartbeat every few seconds. A sketch of the (relevant part of) the network: My PC ----- extender ----- modem ^ ^ ^ Wired | Wired | This thing connects two cables to each other All the cabling is gigabit, my network card is a Realtek RTL8168C(P)/8111(P) Family PCI-E Gigabit Ethernet NIC (NDIS 6.20). THe modem is a CBN SVG6540E I have no idea what is going on here and I don't know how to find out either. Any help is welcome! If you need any more info, please ask.

  Read the article

• Using Truecrypt to secure mySQL database, any pitfalls?

  - by Saul

  The objective is to secure my database data from server theft, i.e. the server is at a business office location with normal premises lock and burglar alarm, but because the data is personal healthcare data I want to ensure that if the server was stolen the data would be unavailable as encrypted. I'm exploring installing mySQL on a mounted Truecrypt encrypted volume. It all works fine, and when I power off, or just cruelly pull the plug the encrypted drive disappears. This seems a load easier than encrypting data to the database, and I understand that if there is a security hole in the web app , or a user gets physical access to a plugged in server the data is compromised, but as a sanity check , is there any good reason not to do this? @James I'm thinking in a theft scenario, its not going to be powered down nicely and so is likely to crash any DB transactions running. But then if someone steals the server I'm going to need to rely on my off site backup anyway. @tomjedrz, its kind of all sensitive, individual personal and address details linked to medical referrals/records. Would be as bad in our field as losing credit card data, but means that almost everything in the database would need encryption... so figured better to run the whole DB in an encrypted partition. If encrypt data in the tables there's got to be a key somewhere on the server I'm presuming, which seems more of a risk if the box walks. At the moment the app is configured to drop a dump of data (weekly full and then deltas only hourly using rdiff) into a directory also on the Truecrypt disk. I have an off site box running WS_FTP Pro scheduled to connect by FTPs and synch down the backup, again into a Truecrypt mounted partition.

  Read the article

• Computer loop restarts on Windows loading

  - by Robinson G.

  My computer restarts, just after or during Windows loading (4 squares getting together), or after some time on the desktop IF I'm idle. In order to start the computer I either have to swap my RAM (24Go) in differents DIMM slots, for example (I have 4 slots) : 1-2-4 or 2-3-4 or 1-3-4, not the same position each boot or it restarts in a loop... I can also change the ram timing from 1.5 to 1.6V and it starts, at the next reboot I have to change it again to 1.5 or it won't boot... And If after all, I succeed to boot, I have to use the computer for about 10 minutes, and it's ok, if I don't, it restarts by itself after some minutes. If I stay on the BIOS, It's all OK, I can stay for a whole year without restarting. I have check my RAM on Memtest (4*8G SDRAM DDR3) : OK I have check without graphic card : Still the same. I tried to reset the bios stack by getting it off and on : Still the same. I tried to reset my BIOS, and many settings about the RAM in the menu : Still the same. CPU temps are just fine (around 35°C) I was thinking ofc about the motherboard but I want to be sure. Motherboard : MSI zh77a-g43 RAM : 4*8G Dual Mode or not (depends on the number I put ofc.) PSU : 600W (enough to run all the config) CPU : i7 3770 non K

  Read the article

• Computer not finding hard drives on boot -sometimes-

  - by todd.pund

  Computer specs: Mobo: Gigabyte ultradurable 3 - GA-970A-UD3 Processor: First gen I7 3.2GHZ Ram: 8GB Kingston DDR3 1066 Video Card: EVGA NVidia GTX 460 1GB Hard Drive: 500MB 7200rpm x2 (can't remember brand, sorry I'm at work.) Last week my developer preview for Windows 8 ran out so I put my copy of windows 7 back on the computer. The computer at that point started suffering from frequent freezing and crashing. When I rebooted the computer sometimes it wouldn't find the system HD at all. When I looked at the post screen it seemed to show that it wasn't finding either of the HDs. Then yesterday when turning on the computer I just got GRUB as a message (not a GRUB prompt, just GRUB) I haven't had a dual boot of Linux for at least a year. I loaded windows 7 recovery console from the disk and ran: bootrec /fixboot bootrec /fixmbr Which did not help. At that point I just installed Ubuntu 13.04 over the windows 7 install and still received the GRUB post. I went into the BIOS and switched the Hard Drive priorities and then it loaded into Ubuntu fine. For several days everything was just hunky dory until I installed the Ubuntu version of Steam, install Portal and tried to run it. At that point the computer froze and after hard rebooting couldn't find the hard disks again. Then after restarting the system it loaded up fine again and no issues since. (I have not tried to launch portal again). My next thought is to remove the system hard drive and try to use the secondary as the master to see if the primary HD is bad. I'm sorry if this has been confusing, I'll answer any questions I can. Any thoughts?

  Read the article

• How do I enable Ubuntu Gnome system tools

  - by RussellW

  I am running Ubuntu 10 with Gnome 2.30.2. This is a VMWare workstation image provided by another company that I do not have support in this regard. I am trying to access the graphical tools for configuring the network, users, and services but the System-Administration menu does not have these options listed. The main issue I am trying to solve is to correct the problems with the gnome menu options and network settings I have the gnome-system-tools package installed, and I am unable to run command-line versions of the tools, such as nm-applet (I get no GUI if I run that command, the process is running in the background). I realize that I can perform many tasks command-line, but I would like to use the GUI for administrative functions as I am not overly proficient for all command for restarting services and setting a static IP with a specific gateway. Further, I can run gnome-nettool, but I cannot change the IP, I can only see my network card. nm-connection-editor does not show any network cards that I can configure to change the IP. Currently, I am getting a DHCP through my NAT in VMWare, I want to set it to a specific IP address though. Preferences Menu (note some missing options) ![Preferences Menu][1] Admin Menu (note some missing options) ![Admin Menu][2] Network Tools (I can view but not change IP address) ![Network Tools][3] Network Settings (Unable to change IP address) ![Network Settings][4] Network Connections (no connections listed, not even my existing ethernet NAT connection through VMWare) ![Network Connections][5] See images here that I have referenced: 1- http://i.imgur.com/kl8pP.png 2- http://i.imgur.com/K3Cjz.png 3- Iq7Xb.png 4- 7wheV.png 5- J2ad8.png

  Read the article

• Running computer from separate room

  - by Dan

  I want my computer to be in the basement, but to use it on the first floor. Which cables should I run through the floor? Can some be wireless or other methods? Here are some of the options I've thought of: Basic: Run DVI, usb (mouse), usb (keyboard), and audio cable (4 cables) USB Hub option: Run DVI, and 1 usb, then using a usb hub split it into mouse, keyboard, maybe even audio (2-3 cables) HDMI Option: If I get a new video card and monitor that supports HDMI, would I be able to run both audio and video through it? Would the monitor have to have an audio out? Also there is a lot of extra bandwidth in the HDMI cables, could I send two monitors on 1 cable or would I have to use 2 cables? How about sending mouse/keyboard through the HDMI cable? I see a lot of monitors with USB hubs built in, but I assume I'd still have to wire HDMI + 1 USB cable to use the USB hubs? X Terminal Machine/Thin Client: I don't really know much about this option. Not sure if it would allow me to run graphics acceleration and watch movies, does anyone know more details about what this would allow me to do? Other options: Any other ways to do this? Can any of this be wireless?

  Read the article

• Display errors using VMWare Player and Remote Desktop on Windows XP

  - by Tim

  I've come up against a weird display issue that I can't seem to find any "fix" for. When I first boot up my computer, everything behaves normally. If I start to use VMWare Player and/or Remote Desktop, my desktop starts having some odd video issues. The frames for some windows aren't drawn at all, if I move windows around rapidly, the area under where the window used to be isn't cleared (still shows artifacts of the content of the window), etc. In some cases, the minimize / restore / maximize buttons aren't drawn (but are click-able if you can guess where they are). I've tried the usual stuff - current drivers all around, using a single monitor, etc.. none of it seems to have any bearing. If I try to disable hardware acceleration, it tends to crash the computer. As I said earlier, it's running Windows XP, dual monitors, an NVidia en8400GS video card, asus p7p55d motherboard. Not sure what other pertinent details are needed. I would appreciate any help or suggestions!

  Read the article

• linux shutdown hang with wifi cifs mounts

  - by Sirex

  Since fedora 15 (and now with 16) it seems that wireless clients take a long while to shutdown when they have network filesystems mounted at shutdown time. I've pushed out a cifs mount via puppet, and all clients have it, including those on wireless. If say a laptop is on a wired connection it shuts down just fine, but if its on the wifi at the time (and no wired connection) it'll hang at the fedora f logo. I'm not sure if its indefinite or just a really long while, but ill give it a test when i shut this machine down in a second. Needless to say its pretty annoying, so is there a way of causing the machine to shutdown even if network connectivity has been lost at unmount time, -- or an official way to reorder events so the wireless card is kept up until after the unmount happens during the shut down process (short of writing a custom script for shutdowns which is a bit of a kludge) ? It does this on multiple machines, and all started doing it when we went from fedora 14 to 15. It was such an obvious issue i'd kind of assumed someone must have reported it or there was an easy fix, but i've not discovered anything yet. Additional info: I can confirm that manually unmounting the mounts then shutting down (sudo shutdown or the xfce shutdown button) will shutdown just fine, it only hangs if the mounts are still mounted The puppet config that sets the mount looks like this (now with the _netdev entry that is indeed pushed to clients successfully, but makes no difference): file { "/mnt/share": ensure = directory,} mount { "/mnt/share": atboot = true, ensure = mounted, remounts = false, fstype = cifs, device = "//srv/share", options = "user,gid=shareusers,uid=${user},file_mode=0700,dir_mode=0700,credentials=/root/.smbcreds,_netdev", require = [ File["/mnt/share"], Group["shareusers"] ], } }

  Read the article

• iptables rule on INPUT between 2 ethernet cards on the same host

  - by user1495181

  I have 2 eth cards on the same host. Both connected directly with LAN cable. I set eth0 with ip - 192.168.1.2 I set eth1 with ip - 192.168.1.1 I set this rule: iptables -A INPUT -p tcp -j NFQUEUE --queue-num 0 There are no other rules. (I ran iptables -X,-F) I send TCP syn packet ( with c++ program by using raw socket) from 192.168.1.2 to 192.168.1.1 In wireshark i see that the packet received on eth0, but the iptables rule (above) dosnt apply for this packet. when i sent the packet to remote host and apply this rule on the remote host than it work correct. So, i guess that this is due to the fact that both eth cards exists the same host. . I need to create iptables INPUT rule for local eth card (dest and src on the same machine ). I need it for simplify test. Did i guess the problem correct? is there a way to bypass this? Ps - connected them via switch didn't help. the rule wasn't applied. Run on Ubuntu. TCDUMP show the packet: 10:48:42.365002 IP 192.168.1.2.38550 > 192.168.1.1.34298: Flags [S], seq 0, win 5840, length 0 but logging of iptables like this, has nothing: iptables -A INPUT -p tcp -j LOG --log-prefix '*****************' iptables -A OUTPUT -p tcp -j LOG --log-prefix '#################'

  Read the article

< Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >