Search Results

Search found 22211 results on 889 pages for 'client identifier'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 210/889 | < Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >

  • Cannot install grub to RAID1 (md0)

    - by Andrew Answer
    I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat This is the my mdadm output after sync: /dev/md0: Version : 0.90 Creation Time : Wed Feb 17 16:18:25 2010 Raid Level : raid1 Array Size : 470455360 (448.66 GiB 481.75 GB) Used Dev Size : 470455360 (448.66 GiB 481.75 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Nov 1 15:19:31 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 92e6ff4e:ed3ab4bf:fee5eb6c:d9b9cb11 Events : 0.11049560 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. This is my fdisk -l output: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057d19 Device Boot Start End Blocks Id System /dev/sda1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sda2 940910985 976768064 17928540 5 Extended /dev/sda5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table This is my grub install output: root@answe:~# grub-install /dev/sda /usr/sbin/grub-setup: warn: Attempting to install GRUB to a disk with multiple partition labels or both partition label and filesystem. This is not supported yet.. /usr/sbin/grub-setup: error: embedding is not possible, but this is required for cross-disk install. root@answe:~# grub-install /dev/sdb Installation finished. No error reported. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... Anybody can resolve this issue? I have big headache with this.

    Read the article

  • How to get Synergy working on Ubuntu 11.10 and Windows 7?

    - by Linda
    I'm using Ubuntu 11.10 32-bit and Windows 7 64-bit, however, Synergy only works when a window (application or folder) is open and touching the edge of the screen where the mouse should "jump". In other words, if a window is open and maximized, Synergy works normally. Without any windows, the mouse does not jump to the other screen. My steps: (Ubuntu) apt-get install -y quicksynergy (Windows) Install Synergy (I've tried both 1.3.8 and 1.4.8 and both 32 and 64-bit) On Ubuntu 11.10 32-bit (Synergy Server config): ~/.quicksynergy/synergy.conf section: screens myubuntu: mywin7: end section: links myubuntu: right = mywin7 mywin7: left = myubuntu end On Ubuntu 11.10 32-bit: $ /usr/bin/synergys -f --config .quicksynergy/synergy.conf ... 2012-04-25T14:04:12 NOTE: client "mywin7" has connected /build/buildd/synergy-1.3.6/lib/server/CServer.cpp,287 (output hangs here) On Windows 7 64-bit: Synergy 1.3.8 Client on Microsoft Windows 7 x86 (WOW64) started client connecting to 'myubuntu': ###.###.###.###:24800 connected to server (output hangs here) At this point, things should work, but my mouse still can't change screens unless a window is maximized on my Ubuntu machine. Everything is running on port 24800. No firewall on Ubuntu. Firewall port 24800 open on Windows 7. This was previously working on Ubuntu 10.10 and Windows 7 (so only Ubuntu has been upgraded). I'm open to using either 32 or 64-bit on either server or client side, but I just want to get it working on Ubuntu 11.10 and Windows 7! I'm also using Ubuntu Classic (no effects), and not Unity.

    Read the article

  • Is there a screen sharing/remote desktop app for mac that lets you use a different host screen resolution?

    - by MarqueIV
    Ok, there are tons and tons of questions about remote desktop for mac and they're all being closed as duplicates. I however am specifically looking for one that will let me use a different resolution than the host, the way you can with Remote Desktop for Windows. For instance, when I connect to my 11" Macbook Air booted into Windows7 from my quad-screen desktop, also booted into Win7 using Microsoft's Remote Desktop Client, it blanks out the screen on the notebook, then virtualizes the video across all four of my desktop's monitors at their native resolutions (2560x1600, 2 x 1920x1200 and 1600x1200) and the notebook now acts as if it has four physical monitors connected to it. All of this from a notebook that only has a 1366 x 768 native resolution. Even when running OS X on the client running RDC, while it doesn't support multi-monitors like its Win counterpart, it still lets me run at the native resolution of the client screen of 2560x1600. Again, it just blanks out the host screen while doing so. However when using Mac's screen sharing, since that is just glorified VNC, it just mirrors what's already on the host's screen, meaning it will always be a single screen with the resolution of 1366x768. This of course makes sense since VNC is a mirroring solution, not a video-virtualizing one like RDC, but it means that on my quad-monitor setup, the remote window isn't even large enough to fill up a single monitor, let alone four (unless you have a client that can scale it up, but that's video scaling. It's still only 1366x768.) So what I'm looking for is if there is a solution on the Mac that lets me do the same thing as RDC in a Win environment. Don't care if I have to pay. I'd gladly pay several hundred dollars for this. I just need that specific feature. Note: People have suggested various VNC clients, but the VNC host still runs at 1366x768 so that will not work here. Ever. Also, people have suggested Synergy/Synergy+/Teleport and such which share the keyboard and mouse, not video. Completely different animal unrelated to what I'm looking for.

    Read the article

  • ESXi 5 Guests will not boot

    - by Adrian
    I have a problem with Guests not booting under VMWare ESXi 5.0 on my IBM x3550M3 server. Note: Investigation eventually determined that problem was with the VMware client on a Lenovo Edge laptop, the only Windows box available in a Linux IT shop. vSphere Client v4 and v5 duplicated behavior on the Lenovo Edge. As indicated in the comment to the accepted answer, replacing the workstation with one using different video was the "fix" for this particular issue. The ESXi host boots just fine. The Client connects just fine. Guests can be configured but do not successfully boot. The initial guest memory consumption jumps up to 560MB and drops down to 40MB after a few seconds. Initial CPU usage is 1 full CPU (3000Ghz per the chart) and immediately drops downm to 29Mhz. Guests do not display any output in the Console tab but show a state of 'Powered On'. No errors in the Events tab. Switching Guest from BIOS to EFI makes no difference. VMs are listed as Version 7 and the behavior is duplicated across all availabled Guest OS flavors. Problem also duplicated when server is booted up in Legacy Only mode. Logs do not contain anything particularly suspicious. Edit: No firewalls, routers, or VLANs in between the client and server. Edit 2: We have tried to Boot Guest into BIOS screen at Next Boot checkbox in the Guest Setting. Was not successful. Edit 3: 500GB datastore with 1 40GB VM on it. Plenty of space. Edit 4: Guests copied from my old ESXi 4 server DO NOT boot on the ESXi 5 system. Initially it complains about too little Video RAM being configured for the default 2500x1600, but it still doesn't work properly even after I bump the Video RAM settings or switch it to Auto-Detect.

    Read the article

  • Oracle Error ORA-12560 TNS:Protocol Adapter error?

    - by David Basarab
    I am using Oracle Database 10g. Both Servers are Windows 2003. I have an Orcale Database set up on one server. Here is the TNSNames.ora from the server with the database. # tnsnames.ora Network Configuration File: C:\oracle\product\10.2.0\db_1\network\admin\tnsnames.ora # Generated by Oracle configuration tools. ORCL.VIRTUALHOLD.COM = (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = databaseServer)(PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = orcl) ) ) The Environmental Variables on the Server are ORACLE_HOME = C:\oracle\product\10.2.0\db_1 ORACLE_SID = orcl I am trying to connect to it from another box that has Oracle Client installed. Here is the tnsnames.ora installed on the other client server. # tnsnames.ora Network Configuration File: C:\oracle\product\10.2.0\client_1\network\admin\tnsnames.ora # Generated by Oracle configuration tools. ORCL = (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = databaseServer)(PORT = 1521)) ) (CONNECT_DATA = (SERVICE_NAME = orcl) ) ) ORACLE_HOME = C:\oracle\product\10.2.0\client_1 ORACLE_SID = orcl Locally on the database server I can connect to through sqlplus with no issues. On the client machine I keep getting the error: ORA-12560: TNS:protocol adapter error What am I missing? Does the client TNSNames.ora need to be different?

    Read the article

  • How to configure Windows user accounts for ODBC network with NT authentication?

    - by Ian Mackinnon
    I'm trying to create a connection to an SQL Server database from the ODBC Data Source Administrator using "Windows NT authentication using the network login ID". Both server and client are running Windows XP. It appears that any account with administrator privileges can add the data source on the server*, though connection attempts from the client result in error messages that suggest it is trying to authenticate using a guest account. I found a Microsoft support page that says: For SQL Server...: connect using the impersonated user account. But it doesn't offer advice about how to do that. How do I impersonate a user account on the server? or (since it sounds like that would lead to an unfortuante squashing of privileges and loss of accountability): How do I give an account on the client privileges on the server database and then ensure the client attempts authentication with the privileged account and not with a guest account? I'm aware that I'm providing rather sparse information. This is because I'm in unfamiliar territory and don't know what's pertinent. I'll attempt to add any requested information as quickly as possible. *I'm planning on tightening privileges straight after I get it working as it stands.

    Read the article

  • How do you optimize your Outlook Exchange + IMAP setup?

    - by Mike
    My company provides an Outlook/Exchange account we must use for mail/calendar. Like many companies, they unfortunately also provide a ridiculously small mail quota. I got tired of managing and backing up .pst files (since I'm always in my e-mail there is never a good time to back it up), so I started storing my archived mail "in the cloud", using an IMAP server I set up on my Linux box. This has a few drawbacks for me: IMAP (at least the implementation in Outlook) is *very slow*. Furthermore, if I move a large number of messages to the IMAP server, it blocks the entire Outlook client for hours sometimes, which is quite annoying. Can't use exchange over HTTP to do mail without launching a VPN session, because the client-side rules I have which organize my mail fail and disable the rule if the IMAP server can't be reached. If I reply to a message from my IMAP store, I have to specify a SMTP server willing to relay for me in order to send e-mail, unless I always remember to select my Exchange account while composing e-mail. ... but the main advantage of being very easy to back up, with a couple of cron jobs that essentially do an 'rsync'. Short of moving the IMAP server to my local host (which seem like might have the same file locking problems as using a .pst), my options seem limited for solving (1). I'd like to come up with a solution for (2) and (3) though. For problem (2) would it be possible to somehow tell Outlook that the IMAP server is "offline", and have it synchronize my changes during a periodic "send and receive"? If so, I wonder if it would block the Outlook client, like it does in problem (1), and if it would be compatible with the client-only rules I use to sort my mail into folders. I've looked all over the options menu and have not found a way to tell Outlook to not use a certain account for sending mail, which would solve (3). Is anyone else crazy enough to be doing something like this? Any ideas?

    Read the article

  • Setup windows 2012 AD in Hyper-V for a Test environment

    - by hub
    Im trying to setup a Windos 2012 R2 test environment on my work computer (a laptop). I have a AD, DHCP and DNS server on server A, and a client connecting to the doman and that works. The client can ping the AD server and gets a valid IP adress. If I ping google.com from the client I get the IP adress but I dont get any responses (request time out). If i ping google.com from server A it works as it should. Server A have a connection to the Internet through a "external network switch" in hyper-v, which gets its internet from a router and the client is connected to a "internal network switch". May the poblem be that server A is behind a router? Can I make this solution to work regadless the network my laptop is connected to? At home i have one IP adress, at work its a totally different range. What I would like is to use my laptops internet connection, regardless wifi or wired, to act as incomming internet, is this possible?

    Read the article

  • Can My Personal GMail Query A Remote LDAP Server?

    - by Maarx
    I have a personal GMail account, from which I frequently send e-mail to a great many various users of a specific business. The corporation has been kind enough to provide me with the credentials to access their LDAP server, with which I would like my GMail web client to be able to auto-complete partial addresses or names for which that LDAP server has an entry. Is there any way I can get a personal GMail account (or it's corresponding entire Google account) account to incorporate an LDAP server into it's Contacts? If I cannot get it to query dynamically and on-demand, is there an idiot-proof way (assuming the client permits, which they may not) to query the LDAP server for it's entire database, save it, and bulk import it to GMail? Perhaps, even, something I could set to repeat periodically (weekly, perhaps), without human interaction? If I did the latter, I assume it would be trivial to import all of these contacts under a single category that could be easily manipulated from within the GMail web-based client. I have been a staunch user and supporter of the GMail web-based client since it's instantiation, but this one is kind of a deal-breaker for me. If it's impossible, what do you suggest I do?

    Read the article

  • DNS lookup fails when with all the MAC workstations

    - by user39564
    Hi, I am having this insane problem. We are mac-heavy users. Around 10 workstations, one Xserve server, two windows workstation and one Linux (me). Last year I added an A record to our domain's DNS. However we had to change that a few months ago to a new IP. But all the Mac workstations fail to resolve the proper DNS and they still resolve to the old IP, even after 2 months. On both the windows workstation and my linux box a simple nslookup resolves to proper IP. However, on ALL the mac workstation, dig and nslookup report the old IP address. From my linux workstation: jp@lo:~$ nslookup - 208.67.222.222 client.xyz.com Server: 208.67.222.222 Address: 208.67.222.222#53 Non-authoritative answer: Name: client.xyz.com Address: 68.71.40.xx But when I am trying the exact same command from any Mac workstation, I get the old IP: $ nslookup - 208.67.222.222 client.xyz.com Server: 208.67.222.222 Address: 208.67.222.222#53 Non-authoritative answer: Name: client.xyz.com Address: 98.143.155.xx The strange thing is that this only happens in our internal network. No problem from home nor from another server. I did try to flush the DNS, don't worry. It did not help. I am starting to wonder if my router (OpenWRT) or Mac OS X Server is not in some way spoofing the DNS request and thus acting as a cache. Any suggestions/comments would be grateful. Thank you, JP

    Read the article

  • Connect trough remote computer connection

    - by Didac
    First, sorry for my english and my poor knowlodge of this subject. I have a dedicated server placed in Germany (windows 2008 R2) and I live in spain. I would like to access internet from my home computer (Windows 7 Pro x64), trough my server in Germany, so I can use a German IP, what I need some times. I have complete acces in to both computers, but I just don't know where to start. (My knwoledge is limited to software development :/ ) I'd like to know where to start, if I need to create a VPN and so.. Thanks in advance! Update 1 I tried a lot of options of OpenVPN, but I sadly I know nothing abuot networking, so I have to accept I do not know what I'm doing :( Here are my config files (note most of the options are from the sample config files). server.conf #server config file start port 1194 proto udp dev tun server 10.0.0.0 255.255.255.224 #you may choose any subnet. 10.0.0.x is used for this example. ca "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\ca.crt" cert "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\server.crt" key "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\server.key" dh "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\dh1024.pem" push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" #the following commands are optional keepalive 10 120 comp-lzo persist-key persist-tun verb 5 #config file ends client.conf #client config file start client dev tun proto udp remote 176.9.99.180 1194 resolv-retry infinite nobind persist-key persist-tun ca "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\ca.crt" cert "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\client1.crt" key "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\client1.key" ns-cert-type server comp-lzo verb 5 explicit-exit-notify 2 ping 10 ping-restart 60 route-method exe route-delay 2 # end of client config file And here's the server's network settings: IP address: 176.9.99.180 Subnet mask: 255.255.255.224 Default gateway: 176.9.99.161 Preferred DNS server: 127.0.0.1

    Read the article

  • Problem connecting to remote network using demand-dial VPN interface with Windows Server 2003

    - by Mike Forman
    I have a Windows 2003 server (SP2) that I'm trying to set up route traffic from my local network using a VPN My local network has the following components: Broadband router (192.168.0.1) Windows Server with a single NIC running RRAS (192.168.0.2 def. gateway = 192.168.0.1) Client Machine (192.168.0.3 def. gateway = 192.168.0.1) Using a VPN connection, I am trying to access a remote machine (10.0.0.1 for example) I configured RRAS with a demand-dial interface for the VPN and set it to be a persistent connection. As part of that setup, a static route to 10.0.0.0 (255.255.0.0) was created. When at the console of the server, I can ping 10.0.0.1 with no problems I added a route on the client machine using the following command: ROUTE ADD 10.0.0.0 MASK 255.255.0.0 192.168.0.2 If I run tracert 10.0.0.1 from the client, the first hop is to 192.168.0.2 which tells me that route is working. However, I cannot ping 10.0.0.1 from the client machine. What am I missing? Hopefully something simple.

    Read the article

  • OpenVPN + iptables / NAT routing

    - by Mikeage
    Hi, I'm trying to set up an OpenVPN VPN, which will carry some (but not all) traffic from the clients to the internet via the OpenVPN server. My OpenVPN server has a public IP on eth0, and is using tap0 to create a local network, 192.168.2.x. I have a client which connects from local IP 192.168.1.101 and gets VPN IP 192.168.2.3. On the server, I ran: iptables -A INPUT -i tap+ -j ACCEPT iptables -A FORWARD -i tap+ -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.2.0/24 -o eth0 -j MASQUERADE On the client, the default remains to route via 192.168.1.1. In order to point it to 192.168.2.1 for HTTP, I ran ip rule add fwmark 0x50 table 200 ip route add table 200 default via 192.168.2.1 iptables -t mangle -A OUTPUT -j MARK -p tcp --dport 80 --set-mark 80 Now, if I try accessing a website on the client (say, wget google.com), it just hangs there. On the server, I can see $ sudo tcpdump -n -i tap0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on tap0, link-type EN10MB (Ethernet), capture size 96 bytes 05:39:07.928358 IP 192.168.1.101.34941 > 74.125.67.100.80: S 4254520618:4254520618(0) win 5840 <mss 1334,sackOK,timestamp 558838 0,nop,wscale 5> 05:39:10.751921 IP 192.168.1.101.34941 > 74.125.67.100.80: S 4254520618:4254520618(0) win 5840 <mss 1334,sackOK,timestamp 559588 0,nop,wscale 5> Where 74.125.67.100 is the IP it gets for google.com . Why isn't the MASQUERADE working? More precisely, I see that the source showing up as 192.168.1.101 -- shouldn't there be something to indicate that it came from the VPN? Edit: Some routes [from the client] $ ip route show table main 192.168.2.0/24 dev tap0 proto kernel scope link src 192.168.2.4 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.101 metric 2 169.254.0.0/16 dev wlan0 scope link metric 1000 default via 192.168.1.1 dev wlan0 proto static $ ip route show table 200 default via 192.168.2.1 dev tap0

    Read the article

  • Passing the output of the last command to sed as an argument

    - by neurolysis
    Hi, Basically, I'm wanting to automate adding something to xorg.conf in the right place, I've used some commands to get the line number of the line I want to manipulate, but I'm not really sure how to go about passing this line number (as an argument and NOT something to be manipulated) to sed. I have been told about xargs and looked at the docs on it, but after some reading and experimentation I can't seem to get it to work. In case anyone can think of a better method entirely, the process I want to automate is just finding the line containing both "Identifier" and "Monitor0" (there will only be one) and adding a line below it. The problem with just finding Monitor0 and manipulating that line is that there are multiple lines with Monitor0 in. I've got this far: fgrep -n "Monitor0" </etc/X11/xorg.conf | fgrep "Identifier" | cut -f1 -d: This gives out the line number which I'm wanting to pass to sed, but I'm not really sure how to do it. ...or is there a simpler way which I'm not seeing? Thanks. :)

    Read the article

  • How to wipe the slate clean on an Oracle installation?

    - by nw
    After a basic, successful installation of Oracle 11g, I ran dbca again to enable Enterprise Manager on my database. The operation hung at around 67% for half an hour or more, so I clicked Stop to abort the operation. Things seemed to wrap up cleanly, EM was working, all was well with the world. Then I started getting this dreaded error upon any attempt to connect in SQL*Plus: ORA-12154: TNS:could not resolve the connect identifier specified I thought perhaps the database had been corrupted due to the earlier aborted operation, so I ran dbca again and deleted the database. Then I attempted to create a new database in its stead, using a clone of the template created the first time around. Unfortunately, the clone database operation fails at 50% with the exact same error: ORA-12154: TNS:could not resolve the connect identifier specified How can I clean up the mess I have created, short of reinstalling Oracle entirely from scratch?

    Read the article

  • Steps to debugging web site latency and timeout issues

    - by Paperjam
    I have a client who has multiple offices around the country, all of which share the same Internet connection via their WAN. One specific office for this client is experiencing severe latency and timeout issues with my web site. Most, but not all, of the latency occurs on a specific ASPX page where multiple postbacks are made while populating cascading dropdown lists (rapid form submits). The latency is sporadic and can be anywhere from a few seconds to a full timeout. There is no indication that the timeouts are occurring on the server's end. The IT guy for this client is having trouble narrowing down the problem. Since it is affecting only one location for one client, I am led to believe it is not something with my site but something specific to that location. He's measured ping times while using the site and has noticed no real variance in ping times even when the page has timed out. I believe this may be being caused by some sort of Internet filter that doesn't like rapid form submits, but beyond a hunch I haven't a clue. My question is what things should I tell the IT guy to look for? While I'm not trying to provide active tech support for this issue, I would at least like to glean an understanding of what is going on and try to offer some sort of advice. Thank you.

    Read the article

  • Configuring SQL Server Express 2005

    - by MrTognio
    What's the proper way to configure SQL Server Express 2005 so that it can allow for a number of clients to get connected to the server? I have my application running both in the server machine and the client machines. Given the nature of my application, clients are the branches geographically distant from each other, and the server itself. Every operation the client records must be reported to the server, because the server needs total control over the usage and production. But, what should I consider when configuring the connection in both sides, the server and the client? I'm not as used to SQL Server, I'm a beginner, however through SQL Server Configuration Manager I have set the main options without success. The problem seems to be related to trusted connections even though I have set it to support both windows and SQL Server authentication. When the client tries to connect to the server using windows authentication it displays no table; when it tries to communicate using a password (SQL Server authentication), tables are successfully displayed but no access is allowed... Thanx in advance!

    Read the article

  • is there a man in the middle attacking to my server machine?

    - by GongT
    My server works well about half a year. But a strange thing happened (several hours before). This server has two IP-address 58.17.85.19 & 117.21.178.19 When I navigate to http://58.17.85.19, nothing different as before. But http://117.21.178.19 will return a "302 Object moved" and become a "redirect loop" I do some test: ($cmd = "wget http://117.21.178.19/?xx=$RANDOM --max-redirect 0 -S --no-cache -O -") Step by step: run $cmd on my PC and my firend's one (we live in two side of China, far away). - got 302 run $cmd on this server - got 200 OK (content is correct result of index.php) run $cmd on another server in same computer room - got 200 OK telnet from my PC and build an HTTP request (type by hand) - got 200 OK shutdown php-fpm, run $cmd on my PC - got 302 run $cmd on server - 502 Bad Gateway shutdown nginx, run $cmd on both the server and my PC - Connection refused. create iptables rule, refuse any connection to 58.17.85.19:80. run nc -l 80 -k -vvv on server and run $cmd on my PC NC show me that.... Server accept connection (Connection from [my ip]) My connection closed ! (Remove fd xx from list) wget dump out response - got 302 I know that, normaly, NC will accept connection, then dump HTTP request from client, and client will wait for response. this connection will open forever(infact client will close connection becouse timeout), becouse NC can't give any response. So... where my request gone? who send an response to the client? some virus on my server system? If so, why 58.17.85.19 didn't has this error? or... I was attacked by a middleman?

    Read the article

  • OpenVPN + iptables / NAT routing

    - by Mikeage
    I'm trying to set up an OpenVPN VPN, which will carry some (but not all) traffic from the clients to the internet via the OpenVPN server. My OpenVPN server has a public IP on eth0, and is using tap0 to create a local network, 192.168.2.x. I have a client which connects from local IP 192.168.1.101 and gets VPN IP 192.168.2.3. On the server, I ran: iptables -A INPUT -i tap+ -j ACCEPT iptables -A FORWARD -i tap+ -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.2.0/24 -o eth0 -j MASQUERADE On the client, the default remains to route via 192.168.1.1. In order to point it to 192.168.2.1 for HTTP, I ran ip rule add fwmark 0x50 table 200 ip route add table 200 default via 192.168.2.1 iptables -t mangle -A OUTPUT -j MARK -p tcp --dport 80 --set-mark 80 Now, if I try accessing a website on the client (say, wget google.com), it just hangs there. On the server, I can see $ sudo tcpdump -n -i tap0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on tap0, link-type EN10MB (Ethernet), capture size 96 bytes 05:39:07.928358 IP 192.168.1.101.34941 > 74.125.67.100.80: S 4254520618:4254520618(0) win 5840 <mss 1334,sackOK,timestamp 558838 0,nop,wscale 5> 05:39:10.751921 IP 192.168.1.101.34941 > 74.125.67.100.80: S 4254520618:4254520618(0) win 5840 <mss 1334,sackOK,timestamp 559588 0,nop,wscale 5> Where 74.125.67.100 is the IP it gets for google.com . Why isn't the MASQUERADE working? More precisely, I see that the source showing up as 192.168.1.101 -- shouldn't there be something to indicate that it came from the VPN? Edit: Some routes [from the client] $ ip route show table main 192.168.2.0/24 dev tap0 proto kernel scope link src 192.168.2.4 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.101 metric 2 169.254.0.0/16 dev wlan0 scope link metric 1000 default via 192.168.1.1 dev wlan0 proto static $ ip route show table 200 default via 192.168.2.1 dev tap0

    Read the article

  • HTTPS Proxy which answers CONNECT with own certificate

    - by user1109542
    I'm configuring a DMZ which has the following Scheme: Internet - Server A - Security Appliance - Server B - Intranet In this DMZ I need a Proxy server for http(s) connections from the Intranet to Internet. The Problem is, that all Traffic should be scanned by the Security Appliance. For this I have to terminate the SSL Connection at Server B, proxy it as plain http to Server A through the Security Appliance and then further as https into the Internet. An encryption is then persistent between the Client and Server B and the Target Server and Server A. The communication between Server A and Server B is unencrypted. I know about the security risks and that the client will see some warning about the unknown CA of Server B's certificate. As Software I want to use Apache Web Servers on Server A and Server B. As first step I tried to configure Server B that it serves as endpoint for the SSL Encryption. So it has to establish the encryption with the client (answering HTTP CONNECT). Listen 8443 <VirtualHost *:8443> ProxyRequests On ProxyPreserveHost On AllowCONNECT 443 # SSL ErrorLog logs/ssl_error_log TransferLog logs/ssl_access_log LogLevel debug SSLProxyEngine on SSLProxyMachineCertificateFile /etc/pki/tls/certs/localhost_private_public.crt <Proxy *> Order deny,allow Deny from all Allow from 192.168.0.0/22 </Proxy> </VirtualHost> With this Proxy only the CONNECT request is passed through and an encrypted Connection between the client and the target is established. Unfortunately there is no possibility to configure mod_proxy_connect to decrypt the SSL connection. Is there any possibility to accomplish that kind of proxying with Apache?

    Read the article

  • VPN Authentication Credentials (Local/Remote Identifiers) For Remote Access VPN

    - by thatidiotguy
    So I am trying to set up a remote access VPN using the free ShrewSoft vpn client: https://www.shrew.net/software I want to use a PSK as the authentication mechanism combined with XAuth so that a connection requires a valid username/pass combo. Under the authentication tab this particular VPN Client however is asking for a Local Identity and a Remote Identity. The options for Local Identity Type are: Fully Qualified Domain Name User Fully Qualified Domain Name IP Address Key Identifier The options for Remote Identity are: Any Fully Qualified Domain Name User Fully Qualified Domain Name IP Address Key Identifier My current thinking is that I can use the Fully Qualifed Domain Name provided by the remote firewall for the Remote Identity, but I do not know what it wants for local identity. Just to stress: I am not trying to set up a site to site VPN. Can anybody shed any light on what I am missing here? A screenshot can be provided if that would be helpful. The current error I am getting during the connection is: IKE Responder: Proposed IKE ID mismatch

    Read the article

  • Autossh startup on Ubuntu 10.04 - fails after powering off

    - by grant
    I'm using upstart to keep a reverse ssh tunnel alive using auto ssh similar to Using Upstart to Manage AutoSSH Reverse Tunnel. This works fine, except after a manual power down I can no longer connect to the machine through the "central server" using the tunnel. I receive "ssh_exchange_identification: Connection closed by remote host". The autossh process is running on the client. I can connect again after re-starting networking. I'm trying to figure out why this is failing consistently after a manual shutdown. Is it possible that I need to do some cleanup on startup that would allow the tunnel to work in this situation, or are there some other debugging/troubleshooting steps I can take to determine the problem? Machine A is the client machine, using autossh. This machine sits behind a firewall and uses the following command in upstart to create an ssh tunnel: /usr/bin/autossh -fN -i /keyfile -o StrictHostKeyChecking=no -R 20098:localhost:22 user@centralserver Machine B we'll call the "central server", which sits in the cloud and is the host. This machine is "centralserver" in the command above. When Machine A is hard powered off, and back on, I cannot connect to it by SSH'ing from my machine (C) to Machine B in the cloud, then using the following command to get to Machine A: ssh -p 2098 user@localhost Again, after a reboot of the client (A), this works fine. It is only after a hard power down that the problem occurs. There are autossh processes that are running on the client machine (A) after powering down and back up, but they just don't seem to doing their job.

    Read the article

  • Why can I not edit, delete directories inside of this directory

    - by user43053
    Hello there, First, I thought this was PHP related, but maybe it isn't. My original post, which may be irrelevant now is located at the bottom. The problem is I have a directory : /articles/. In it are 10 sub directories. I have been changing the permissions lately, but now it seems all the permissions of the parent folder, sub-folders and files are either chmod 755 or 777. I cannot move, delete or edit files inside of this parent directory or sub-directories with my FTP-client. I can however edit, delete, create new files and directories and change them with PHP-functions without problems. What may the problem be? OLD POST. Ignore everything below this line: If I create a directory with mkdir(), or create a file with fopen(), file_put_contents() or SimpleXMLElement::asXML(), I am unable to access the file with my FTP-client or c-Panel File Manager. If I try to delete or edit them, I get errors. Dreamweaver suggests it is a permission problem or a network or filesystem fault (but I've set the permissions with chmod() to 0777, and when I check the cPanel, it confirms chmod 777. I also tried to use fileowner() and the function returns int(99), the same owner as those files that I could access with my FTP-client. It seems files and directories created with PHP can only be modified or be deleted with PHP. I thought this must be a server setup related issue, so I write it here. I am on a shared server, and I have no idea about setting up servers. EDIT: It seems the problem is different. I cannot move files with FTP-client to the parent, or sub-directories either. This problem may not be PHP related, then. It seems the problem applies to any directory, regardless of whether it was created by PHP. EDIT 2: The parent directory has chmod 755. Thank you for your time. Kind regards Marius

    Read the article

  • Why is my portable WD MY PASSPORT drive is not recognized?

    - by kloop
    My "MY PASSPORT" (Western Digital) portable drive is not recognized OSx. It used to be recognized, but not anymore. It does not appear in /Volumes. The hard drive is recognized by a Linux machine. I am not sure what happened -- any ideas how to fix that? Thanks. EDIT: ` #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *750.2 GB disk0 1: EFI 209.7 MB disk0s1 2: Apple_HFS Macintosh HD 749.3 GB disk0s2 3: Apple_Boot Recovery HD 650.0 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: FDisk_partition_scheme *1.0 TB disk1 1: DOS_FAT_32 MY PASSPORT 1.0 TB disk1s1 `

    Read the article

  • How do I setup an Alias on Apache with XAMPP on Linux ? (Permission problem)

    - by knarf
    XAMPP works fine but I want to have http://localhost/f to point to /home/knarf/prog/php/fwyxz. I've chmod -R 777 /home/knarf/prog/php/fwyxz I've added Alias /f /home/knarf/prog/php/fwyxz at the end of the httpd.conf And when I try to access it, I get a 403. From the apache error_log: [error] [client 127.0.0.1] (13)Permission denied: access to /f denied. I've already tried several solutions (userdir and symlinks) but they both failed with the same error. I've also tried to add this after the Alias: <Directory "/home/knarf/prog/php/fwyxz"> Order allow,deny Allow from all </Directory> But again, permission denied. Now if I change the User/Group under which apache runs from nobody to knarf, it seems to work (static files are ok) but PHP can't use/initialize sessions : [error] [client 127.0.0.1] PHP Warning: session_start() [function.session-start]: open(/tmp/sess_r5nrmu4ugqguqqe83rs53lq6k0, O_RDWR) failed: Permission denied (13) in /home/knarf/prog/php/fwyxz/index.php on line 3 [error] [client 127.0.0.1] PHP Warning: Unknown: open(/tmp/sess_r5nrmu4ugqguqqe83rs53lq6k0, O_RDWR) failed: Permission denied (13) in Unknown on line 0 [error] [client 127.0.0.1] PHP Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct () in Unknown on line 0 This is really frustrating.

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >