Search Results

Search found 6030 results on 242 pages for 'quartz graphics'.

Page 212/242 | < Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >

• My desktop has started overheating -- how hot is hot?

  - by Jerry

  I have a two year old desktop, some random quad core HP desktop. It used to run very quietly, but in the past month, the fans start up anytime anything "serious" is being done -- compiles, playing video, etc. Right now, speedfan and speccy report the cores are between 50C and 70C. Speedfan reports this as hot. (Nice flame icon.) Well, the system does sit on my carpet, so two weeks ago, I took off the lid, and cough *cough* it was pretty filled with dust. I got out an air can, turned on a vacuum and carefully got out all the dust that I saw on the CPU fan the case fans any fan I saw (graphics board) and blew out all the dust I could from all the circuit boards. And then I closed the case back up. It has definitely run cooler since then, but it still runs hot, and I hear high speed fan noise I never heard before. How hot is too hot? At what temps do consumer grade CPUs die? What should I be looking to do? Replace CPU fan? (It seems to work) Replace power supply fan? Assuming the dust problem is gone, where should I be looking to determine why the machine is heating up? Epilogue: After following the various pieces of advice given here, the system did run cooler, but it was still noticeably running louder (hotter) than just a few months prior. I ended up purchasing a new cpu heatsink and fan and during installation found the cooling grease from the original heatsink was just a dried, cracked layer, probably more of an insulator than heat transfer agent. With the new fan AND the new heatsink compound, the system ran much much cooler and the fan rarely turns on.

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• Video output vanishes and it isn't the video card... suggestions?

  - by Ira Baxter

  I have a high-end dual processor Dell workstation that operated for several years without problem. Recently, the video output has gone flaky, in the sense that after 2-3 days, it loses synch with the monitor (sometimes you can still see a hashed-mess of the what you expect to see on the screen). Poking at the keyboard, and accessing the file system on the machine from over the network, indicates that the machine is running fine and its just the video. A reboot fixes the problem... for another day or two. This in effect makes the machine unusable. So, I replaced the video card with an exact duplicate bought from e-bay. (I checked after the dupe arrived to be sure, yep, same model number). I still get the same behavior. So unless I believe that both video cards are broken the same way, I have to beleive this is a problem with the motherboard/power supply, neither of which I am inclined to replace. The only other possibility I can think of is a Windows update to the graphics driver. How would I check for this? Anybody had a similar problem? Otherwise we're junking what used to be a perfectly good machine. (Another couple of hours of more wasted effort and that's it in terms of economics anyway).

  Read the article

• Looking for an application that scrolls or pans netbook screens running Windows

  - by Rob

  I'm looking for a Windows 7 and XP compatible Windows desktop panning/scrolling tool. This is to solve a problem where some applications for example MSN have settings/preference Windows that are not resizeable. I have a Netbook with a small maximum screen resolution e.g. 1024x600. The fixed non-resizeable windows are too large for this display screen size so I cannot see all of the items on these windows, particularly the OK button to save settings. What I would like is a desktop scrolling/panning tool where if I move my mouse pointer to any edge of the display, it pans to show the region of the too-large-fixed window that I could not see. I use a Samsung N110 and Toshiba NB100 netbooks. I'm looking for: A general program that provides desktop panning/scrolling/expanded resolution to allow all regions of a non-resizeable fixed window Preferably a non-graphics hardware specific program but will accept a solution that works with both the above machines I'm NOT looking for (i.e. unsatisfactory answers others have asked that I've already searched and found): Advice on what programs to use that DON'T have the problem of fixed windows Alternative operating system solutions Plugging in an external monitor with larger resolution - I use this option but I need a solution when one is not available, e.g. while travelling etc Advice about not using small screen netbooks - I enjoy the compact convenience of them Advice about change the dpi settings in the Control Panel Display settings Advice about guesswork with the tab key to move the focus the off-screen item I cannot see Thank you in advance.

  Read the article

• Windows 7 blank dvi screen

  - by user99

  I've just upgraded to Windows 7 Ultimate 64 bit. I had an issue during installation; after setup rebooted instead of going to the 'Completing installation' screen I just got a blank screen. I eventually(!) figured out that this meant 'un-plug your second monitor to proceed'. When I did this, installation completed in a snap and everything runs fine. However, whenever I plug my second monitor into my PC, it gets no signal, the the primary monitor removes all windows. icons, the taskbar and the cursor just shows the desktop wallpaper. I'm running a GTS8800 512mb, with the latest drivers (197 IIRC). The monitors are identical, and both plug into DVI sockets on the graphics card, the only difference is I connect one using a straight DVI cable and the other using a VGA cable and a VGA-DVI converter. It's the DVI cabled one that has the issues (if I plug it in by itself it gets no signal). Everything was working fine before I upgraded to Windows 7 (I used to run XPSP2). Anyone have any ideas?

  Read the article

• Reduce power consumption of gaming computer while idle

  - by White Phoenix

  This is my current build: EVGA X58 (first generation) motherboard Intel i7 965 clocked @ 3.3 Ghz 3x DDR3-1600 Corsair RAM at stock timings and voltages Corsair AX750 80 Plus Gold PSU 1 Optical Drive 1 Seagate 7200.10 500 GB drive 2x Western Digital Caviar Black 1 TB drives OCZ Vertex 1 60 GB EVGA GTX 460 oc'd at 800/1600/1850 Antec 1200 case HT-Omega Striker 7.1 Sound Card Windows 7 32-bit Professional (PAE Enabled) I've already seen this post Reduce power use on computer and this post How do I lower power consumption of my computer and while useful, I'm looking for answers specific to my build and OS. I'm pretty sure this build is a energy-intensive build by default, but I want to try to reduce the amount of energy my build uses when I leave it idle (when I go to bed or go out, etc). The first requirement for this machine is that I need to leave it on, so I cannot turn it off while it's being unused. I run it as a file server for personal reasons and I also leave it on in case people leave me messages on various IM services and chat clients (IRC, MSN, Steam, XFire, Pidgin, etc). I'm also unable to replace the parts in my computer with a cheaper "greener" part. What are some ways to minimize the amount of power the machine uses? I'm already using a high efficiency power supply (80 Plus Gold), but I imagine there's other things that can be done in the BIOS and Windows' power settings to reduce power usage while I'm not using the computer. From what I can tell, I can't use Sleep since that'll disable network access (whole reason why I leave the computer on in the first place). I already turn off my monitor when it's not in use. I enabled Intel SpeedStep within the BIOS (I know, I have a 965 and why am I enabling SpeedStep?) Should I bring the graphics card back to stock speeds and lower the clock on the processor even more? Main reason why I'm asking is I think this computer alone is the reason why my power bill is high, so I want to reduce its consumption to as low as possible without having to shut the thing down.

  Read the article

• Netbook thinks it is a desktop

  - by Narcolapser

  Question: Are, and if so what, there packages for download that I can get netbook to understand it is not a desktop and that it is a netbook. Info: I'm running an Acer Aspire One with ubuntu desktop 9.10. I tried Ubuntu Netbook Remix first but it has graphics issues with the aspire one. So I changed to Ubuntu Desktop. It was the only distro (after debian, centOS, Fedora, and Knoppix all failed me) that I managed to get working. The only thing is that it is having issues doing things that a netbook/laptop should be doing. most notably is that it will run it's battery dead if I close the screen and throw it into my back pack. It seems to just stay fully on and runs it's self to death. also it will lock up some times if I close the screen and come back to it 10 or 20 minutes later. It also won't retain volume settings when I reboot, as well as screen brightness. and just a couple of other things that I can't quite put my finger on, but just seem amiss. like I said, Essentially my netbook thinks it is a desktop, how can I fix this? ~N

  Read the article

• Can't set screen brightness in Gentoo system

  - by Real Yang

  My system: Linux gentoo 3.10.7-gentoo-r1 VGA compatible controller: NVIDIA Corporation GT216M [GeForce GT 240M] (rev a2) output of xbacklight: No outputs have backlight property output of xrandr: xrandr: Failed to get size of gamma for output default Screen 0: minimum 640 x 480, current 1280 x 720, maximum 1280 x 768 default connected 1280x720+0+0 0mm x 0mm 1280x720 0.0* 1024x768 61.0 800x600 61.0 640x480 60.0 1280x768 0.0 output of ls /proc/acpi: button/ event When I'm in kernel 3.8.13, I can change my brightness using xbacklight. I compiled 3.10.7-r1 using genkernel all. Before the upgrade I did get a notice of "compatible issues for Nvdia users" from emerge but I still don't know the details. It there anyway to let me set the brightness? Then i found a ebuild app-laptop/nvdiabl-0.81 and tried to emerege nvidabl, I got this message: Your kernel does not support FB_BACKLIGHT. To enable you it you can enable any frame buffer with backlight control or nouveau. Note that you cannot use FB_NVIDIA with nvidia's proprietary driver Please check to make sure these options are set correctly. Failure to do so may cause unexpected problems. Once you have satisfied these options, please try merging this package again. ERROR: app-laptop/nvidiabl-0.81::gentoo failed (pretend phase): Incorrect kernel configuration options Call stack: ebuild.sh, line 93: Called pkg_pretend nvidiabl-0.81.ebuild, line 31: Called linux-mod_pkg_setup linux-mod.eclass, line 559: Called linux-info_pkg_setup linux-info.eclass, line 911: Called check_extra_config linux-info.eclass, line 805: Called die The specific snippet of code: die "Incorrect kernel configuration options" [SOLVED] I enter the menuconfig again and check the Device Drivers -> Graphics support -> Support for frame buffer devices, then i found this: <*> nVidia Framebuffer Support [*] Support for backlight control (NEW) What can i say. Recompiling...

  Read the article

• What do I need to consider when buying hardware to meet my needs?

  - by Darth Android

  I'm looking to build a new computer from the ground up. I'm not sure what to look out for and need guidance and help on how to pick the hardware needed to construct my new rig. How do I know what to buy? How do I find out if a given CPU will be enough for a certain game or application that I want to run? How do I find out if a given graphics card will be enough for a certain game or application? What is important when looking at motherboards? How much memory do I need? How do I know how much wattage I need for a power supply? What size case do I need? What relevant standards do I need to read up on and be aware of? PCI, PCIe, SATA, USB 2.0, USB 3.0, etc... What "gotchas" do I need to be on the lookout for? Please keep responses generation-agnostic to ensure they will be helpful to our future users. While Stack Exchange does not permit shopping recommendations, it doesn't provide any general advice to consider when buying hardware. So, instead of just telling those that ask what to buy that it's not allowed, let's tell them how to figure out what they need. This question was Super User Question of the Week #20 Read the June 20, 2011 blog entry for more details or submit your own Question of the Week.

  Read the article

• Hardware doesn't work some times

  - by Ali

  I have an Asus n51vf laptop. I bought it not long time ago (less than a month) and installed Windows 7 on it. Since that it wasn't new when I bought it, I don't know, if the problem was occuring before re-installing Windows 7. There are two problems, that might (or might not) have something to do with each other: Problem The less annoying problem is that the screen flickers ONLY on YouTube when scrolling and/or pausing/playing the video or moving the curser over the video. The second more timeconsuming problem is that some of the hardware doesn't work when I turn up the computer. Then I have to reboot the computer and try again. Example: I turn on the computer, and the touchpad doesn't work - I then reboot and it works again. This has so far happened to the screen (leading to a black screen), the keyboard and the touchpad. More frequently the mouse. What have I tried to do so far? I tried reeinstalling the touchpad driver (Synaptic Touchpad driver from Asus Support Page) - didn't help at all. I even tried reinstalling the driver when the non-responding mouse on startup-problem occured (using the keyboard), but it asked me to reboot and didn't help at all. I also installed (and reinstalled) the graphics driver; it's a GeForce GT 130M. Now, the problem never occurs spontaneously - it only appears when booting my computer. I can even use the computer for heavy tasks (games, multiple programs running etc.) with no problem at all. I suspect, that the problem is in some booting mechanism that fails: Maybe the Windows driver loading? Motherboard problems?

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro to watch TV and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing TV okay (with the new DirecTV) before I tried to run setup. (I ran setup to try to do recording with Media Center.) Hardware/Software: Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• No audio in my ubuntu system

  - by hap497

  Hi, I am running ubuntu 9.10. But there is no sound in my environment. When I go to System-Preference, there is no 'sound' entry there. $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: I82801AAICH [Intel 82801AA-ICH], device 0: Intel ICH [Intel 82801AA-ICH] Subdevices: 1/1 Subdevice #0: subdevice #0 $ lsmod Module Size Used by usb_storage 52576 3 binfmt_misc 8356 1 vboxvfs 34620 0 vboxvideo 1884 1 drm 159584 2 vboxvideo agpgart 34988 1 drm snd_intel8x0 30168 2 snd_ac97_codec 101216 1 snd_intel8x0 ac97_bus 1532 1 snd_ac97_codec snd_pcm_oss 37920 0 snd_mixer_oss 16028 1 snd_pcm_oss snd_pcm 75296 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_seq_dummy 2656 0 snd_seq_oss 28576 0 iptable_filter 3100 0 snd_seq_midi 6432 0 ip_tables 11692 1 iptable_filter x_tables 16544 1 ip_tables snd_rawmidi 22208 1 snd_seq_midi snd_seq_midi_event 6940 2 snd_seq_oss,snd_seq_midi ppdev 6688 0 snd_seq 50224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event snd_timer 22276 2 snd_pcm,snd_seq snd_seq_device 6920 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq psmouse 56500 0 serio_raw 5280 0 snd 59204 14 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_ oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_ti mer,snd_seq_device i2c_piix4 9932 0 parport_pc 31940 0 soundcore 7264 1 snd snd_page_alloc 9156 2 snd_intel8x0,snd_pcm vboxguest 143836 7 vboxvfs lp 8964 0 parport 35340 3 ppdev,parport_pc,lp pcnet32 32644 0 mii 5212 1 pcnet32 floppy 54916 0 ~:987:2$ lspci 00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC [Natoma] (rev 02) 00:01.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] 00:01.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter 00:03.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 40) 00:04.0 System peripheral: InnoTek Systemberatung GmbH VirtualBox Guest Service 00:05.0 Multimedia audio controller: Intel Corporation 82801AA AC'97 Audio Controller (rev 01) 00:06.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB 00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 0 00:0b.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller ~:988:3$

  Read the article

• How to get a higher resolution on Ubuntu 11.04 using an intel chipset

  - by Saif Bechan

  I have a bit slow PC here, so I decided to put Ubuntu 11.04 on it. It use to run Windows Vista on a resolution of 1280x1024, so both my hardware and monitor support it. Now I'm on Ubuntu, but can only run 1024x768, and the screen is not that bright. Its like when you don't have the right drivers on a Windows machine. Now i'm new to linux, so I do not know what do do. I have an onboard Intel chipset i965. Maybe this is some useful information, I read something about it on a forum: lspci 00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 02) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) 00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 03:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) Can someone please tell me how I can get the screen better? saif@sodium:~$ xrandr Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0* 800x600 60.3 56.2 848x480 60.0 640x480 59.9

  Read the article

• Can Xen be configured to dedicate only one port of a dual-port NIC to a domU?

  - by jamieb

  I'm using CentOS 5.4 on my dom0 with a stock Xen kernel. I'm attempting to use the pciback module to hide some of the Ethernet ports from the host and reserve them for a domU I intend to use for a firewall (process described here). However, when I launch the domU, I get the following error message: Using config file "/etc/xen/firewall". Error: pci: improper device assignment specified: pci: 0000:01:04.0 must be co-assigned to the same guest with 0000:01:06.0, but it is not owned by pciback. lspci gives me the following output: 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) From the sound of the error message, it seems like I also need to dedicate eth0 (PCI ID 01:04.0) to the domU. Am I correct? If not, what am I doing wrong? Thanks!

  Read the article

• Building a PC, advice on SSD/Hybrid Hard Drives

  - by Jamie Hartnoll

  I am looking at building a new PC, it's mainly for office (graphics heavy) use and programming. Looking for good performance with opening and closing programs and files as well as a fast boot. I plan to have 3 primary hard drives Windows 7 Programs (photoshop etc) Current Files (There'll also be a large storage capacity back up drive, but this will be the Seagate drive I already have.) So, my question is, looking at standard "old fashioned" hard drives and SSD drives, obviously there's a massive price difference. I have been looking at drives like this: http://www.ebuyer.com/268693-corsair-120gb-force-3-ssd-cssd-f120gb3-bk-cssd-f120gb3-bk and this: http://www.ebuyer.com/321969-momentus-xt-750gb-sata-2-5in-7200rpm-hybrid-8gb-ssd-in-st750lx003 Having no experience of using either I don't know what's the most efficient thing to go for. Clearly the SSD will have better performance, but: If, for example, I had an SSD for Windows (say about 100gB), that would clearly give me the boot speed I want, then I guess my real questions are: If I were to buy one more SSD, would it give the greatest improvement on standard performance if used to store programs, or currently used files? Given that the OS is on an SSD, should I not bother with the 3 drives and instead, partition that Hybrid drive to store programs and currently used files on it? Obviously, option two is cheaper and option one could cause me storage issues, but that's when I can dump files I am not currently using onto another drive. Any, I am open to suggestions... so what do you suggest?!

  Read the article

• Windows 7 x64 RTM USB Port Has Power But Won't Recognize Mouse/Keyboard/Anything

  - by ben

  I have an odd error that doesn't seem to fit in with any of the other odd Windows 7 x64 USB errors that have been kicked up on Google. Here we go: Uninstalled Tortoise SVN and clicked restart computer. My machine had been up for around 28 days On reboot my mouse and keyboard failed to work anymore, couldn't log in. Tried every USB port I have on my Dell 390 and the ports on my Dell 19's, nothing worked. They had power but Windows would not respond when I manipulated the keyboard/mouse. Rebooted my computer and pressed F2 to get into bios, my keyboard is working fine in bios. Keyboard and mouse work fine on other computers when using USB. Found adapters for keyboard and mouse to convert from USB to PS/2 ports, works fine. I'm actually typing this question on the same keyboard, same computer, just using PS/2 ports for my mouse and keyboard. It appears to be a Windows 7 x64 issue. Other things I have tried: Multiple other mice and keyboards, iphone, all with no luck. Each one gets power, but Windows never tries to install drivers or sees that they are connected. Uninstall and reinstall all USB drivers. Drives uninstall and reinstall fine and report no errors in Control Panel. In Power Management I disallow Windows from turning off USB ports to save power Installed the latest nVidia drivers for my graphics card, no change. Anyplace else I can look/try? Thanks!

  Read the article

• Looking for suitable backup solution Mac OS X to offsite Centos 6 server 1TB of working data

  - by Brady

  I'll start by saying what we have in place currently: On site file server (Mac OS X Server) that is used by GFX designers and they have a working 1TB of data. Offsite server with 2TB available storage (Centos 6) Mac OS X server rsync data to offsite server every 6 hours (rsync -avz --delete --progress -e ssh ...) Mac OS X server does full data backup to LTO 4 tape on a 10 day recycle (Mon-Fri for 2 weeks) rsync pushes about 60GB of file changes a day. The problem: The onsite tape backup is failing as 1TB of graphics files don't compress well to fit onto a 800GB LTO4 tape. Backup is incredibly slow doing a full backup. Pain in the backside getting people to remember to change the tape. Often gets forgotten etc The quick solution: Buy LTO5 Drive and tapes. However this has been turned down because of the cost... What I would like: Something that works in the same way rysnc works. Only changed data is sent over the wire and can be scheduled to run multiple times during the day. Data that is sent is compressed and sent over SSH. Something that keeps a 14day retention but doesn't keep duplicate data So as an example if I have 1TB of working data and 60GB of changes are made each day then I expect around 1.84TB of data to be stored on the offsite server. To work with the Mac OS X server and Centos 6 server. Not cost an arm and a leg. Must be a cheaper solution than buying an LTO5 drive with tapes (around £1500). Be able to be setup to run autonomously. Have some sort of control panel that will allow an admin to easily restore a file/folder. Any recommendations?

  Read the article

• No headphone or speakers plugged in - Windows 7 issue

  - by Amit Ranjan

  I am facing a wierd issue between my sound card driver and Windows7(any edition). I have a sony vaio notebook (VPCEB24EN). Two days ago, on start I got diabled wifi, charging and speakers. Then I restart the PC and everthing worked fine. Later on I again restarted my machine, and then I found the my speakers were not working. I thought, restart will work. I restarted many more times but it did'nt work. I searched google and found that , it might be due to : 1. Hardware is not switched on from bios. 2. No hardware. 3. overriding 64-bit drivers with 32-bit drivers. To make it working, I restored my laptop from scratched, but while restoring pc, the realtek HD drivers, it gave me an error 505. I then formatted the drive and installed Win7 Ultimate 32bit (With PC was, Win7 64-bit Home Basic). I got lots of yellow exclamation in device manager, thinking now this will resolve my issue. But Even after the installing all drivers on a fresh installation, I was still with the same position. A red cross on speaker- No Speakers or Headphone plugged in. Please Note: My Laptop is Vaio , E Series, VPCEB24EN. Audio : Intel® High Definition Audio compatible but accepts Realted Audio. While using BIOS Agent, I got Intel Chipset 5 Series Audio Adapter and ATI RV370 Audio adapter found on my board. Installed is Win7 32bit Ultimate. factory default was Win7 64-bit Home Basic Memory: RAM 3GB/ 320GB HDD Display : ATI Mobility Radeon™ HD 5145 Graphics

  Read the article

• Dual Monitor setup issues between laptop and external led monitor

  - by Julian

  I have two challenges. Monitor will not connect to laptop through HDMI Watching HD video content causes the laptop to sometimes turn off expecially when I'm streaming from tekzilla.com Setup. I got my new HP 2311x LED LCD monitor this week and I have it running as the main monitor extended by the 15 inch screen on my Dell Studio 1558. Right now I have to connect the external monitor through VGA. For the HDMI connection issue. I suspect that either the appropriate drivers are not installed because I don't see any hdmi device in the device manager. I've checked and I don't see any hdmi specific drivers listed online. For the shut down issue, I suspect the laptop might be overheating. Not sure why it would. It never did that while I watched movies on my laptop's default screen. My Laptop Configuration: 15" led lcd screen at 1366 x 768 intel i5 processor integrated graphics card 4 GB DDR3 RAM 500 GB hard drive I've tried everything from switching the source on my monitor to hdmi to start up combinations and nothing has worked. What could be the issue and how do I solve it?

  Read the article

• HP G61 Laptop wont boot- display stays off, caps and num lock indicators blink repeatedly

  - by Benguy12

  I had my HP G61 laptop running in sleep for a while. When I came back to it about a half-hour later, it was no longer in sleep mode - the power light and the Wi-Fi indicator light were on (I keep Wi-Fi off becuase I use a wired connection) - but nothing was showing on screen. In fact, the display wasn't even turned on. So I let it sit for about 10 minutes but nothing happened. I did a force shut down and rebooted. Instead of a normal boot, the display didnt turn on, the Wi-Fi indicator was off, and the Caps Lock and Num Lock lights just blinked repeatedly. On the external keyboard i use, none of the light indicators were blinking or even on. I tried force shut-down again 10 times, then unplugged all connections except for the power cable (my laptop battery dosent hold a charge for more than 2 minutes, so I always must have a wall connection) and tried to boot again but still nothing happened. I unplugged the battery and even then nothing happened. I also tried booting with the disk drive open, and then with it closed again. On the time it was closed, I was able to successfully boot into Windows, but recieved a "Windows did not shut-down sucessfully" notice. Does anybody know why this may have happened? My PC's specs: Windows 7 Home Premium, 64-bit 4GB of physical RAM, 8GB of vRAM (on a flash drive) AMD Vision x64 processor (don't know any other specs about it) ATI Radeon graphics card, 392 MB DVD-R/W lightscribe drive 2 External hard-disks (first one is 1.5TB, second one is 1TB) custom boot-screen and boot-annimation Standard BIOS apps running before sleep: firefox 10.4 itunes 10.6 adobe photoshop extended CS5.1 rockstar games social club (running in background) microsoft powerpoint 2010 professional edition google chrome I was NOT running Aero or any fancy themes - I was using the normal windows classic theme. I have a desktop icon manager application called Stardock Fences that was also running (it runs as a service/process).

  Read the article

• Ubuntu 10.04 freezing and Ctrl + Alt + Backspace does nothing but music keeps playing

  - by Bryce Thomas

  I'm having intermittent problems where the screen will freeze in Ubuntu. I've tried using Ctrl + Alt + Backspace to restart the X-server, though this does nothing. When the freeze occurs, there's a small square of black dashes around the mouse pointer - maybe 1 inch in size. These dashes look a lot like a 2d barcode. The rest of the screen looks normal, but I can't move the mouse and none of the keyboard shortcuts work to do anything. However, music that I begin playing before the freeze continues to play, which seems to indicate it hasn't stalled up completely. I've noticed a similar freezing problem when I'm using Windows 7. That is, I see the same barcode like dashes around the mouse pointer when it freezes up. So I'm guessing it's either a driver or hardware problem. I thought if it was a hardware problem though, the whole computer might stop working (i.e. music would stop playing)? The video card I am using is an Nvidia, and I believe it's in the 7600 range. In Ubuntu I have the drivers for the card set to the latest available (proprietary). Ideally I'd like to be able to continue using the proprietary drivers. Is there any known issues with the drivers for this model graphics card, or has anyone experienced the same problem and knows how to fix it?

  Read the article

• OC'ing a Sapphire 7950, problems with memory clock

  - by Cliff

  I bought a new rig with sapphire radeon 7950 flex w/ boost. Good scores initially in 3dmark 11, around 7300 stock. Problem is, as soon as i start overclocking, issues arise. the core clock is at 860, but rises to 925 with boost applied in pressured situations. So all the OC tools are showing 925 as base clock for some reason. Ocing the core clock has been no problem though, got up to 1200 pretty stable, but only an incremental increase in 3dmark 11, to 7600 from 7300, which is worrying. The real trouble starts when i start touching the memory clock. As soon as i touch it even by 1 point up to 1251mhz, the performance goes way down. suddenly i score under 5000 graphics in 3dmark11, no matter if its 1251hz or 1500hz. Ive tried adjusting every other parameter, different tools (sapphiretrixx, catalyst, afterburner) all still the same. Tried upping the power, still same. Where is the issue here?

  Read the article

• How come my Intel 520 180GB SSD performs extremely poorly?

  - by Willem

  I recently installed a new Intel 520 series 180GB SSD in my brand new MacBook Pro. The system is as follows: Model: MacBook Pro 15-inch, Late 2011 (MacBookPro8,2) Processor: 2.4 GHz Intel Core i7 Memory: 16 GB 1333 MHz DDR3 Graphics: AMD Radeon HD 6770M 1024 MB Software: Mac OS X Lion 10.7.3 Main Drive Bay: Intel 520-series 180GB SATA-3 (6GB/s negotiated link) SSD (Firmware: 400i) [80GB free] Optical Bay: Toshiba 5400 RPM 750GB SATA-2 HDD Trim: Enabled (according to Trim Enabler App) And here are the speeds I'm getting: Read: 412 MB/s Write: 186 MB/s What have I done wrong? Results expected: Read/write both 500MB/s I have seen benchmarks with lesser SSD:s (SATA-2 even) outperform my write-speeds by far. Also, Intel 520 SSD:s are supposed to be the top class of SSD:s. Trim Enabler report: This looks a bit odd compared to screenshots from their site: These is the defined S.M.A.R.T attributes (taken from Intel): And here are my S.M.A.R.T attributes read using smartctl tool from smartmontools: They don't seem very compatible. I'm going to try and look for a S.M.A.R.T attributes reader tool for OS X which might support Intel 520 series.

  Read the article

• Weird PCI bug: lots of missed packets, or data comes in "bursts"

  - by Thomas O

  I have an ABIT KN9 motherboard. It has one PCI-e x16 slot, three PCI-e x4 slots and two legacy PCI. My problem is with the legacy PCI (which I shall just call "PCI".) I currently have an Nvidia GeForce 8600 GT (a low end card) installed in the x16 slot and a TV card in PCI #1; the x4 slots are unused, as is PCI #2. I plan to upgrade the graphics card soon, the current card was spare. I sometimes install a USB expander in PCI #2 but it causes a lot of problems - see below. The problem is under Linux (Ubuntu 10.10, Linux 2.6.35-22-generic), but probably under all operating systems (I have not yet been able to test Windows, but I suspect it will do the same as the problems occur on the BIOS/POST side too, e.g. when using a USB keyboard on the expander the keyboard will not work at all) PCI has an enourmous delay, and packets arrive in large chunks. For example, when using the USB expander, my USB mouse lags and jumps in large steps every second or so, while using the motherboard USB does not present this problem. My TV card will only do one or two frames per second, and the program (xawtv) usually times out and crashes. In dmesg, I'm getting messages like: bttv0: timeout: drop=74, irq=154/100476, risc=31f6256c, bits: VSYNC HSYNC OFLOW RISCI for my TV card, and similar timeout issues for my USB expander with a mouse. I received the motherboard, processor and RAM second hand and have only just got around to building it, so I don't know if this problem has always existed, or if it's a result of my set up. If anyone has any hints or solutions it would be appreciated - this is kind of a show-stopper for me.

  Read the article

• What laptop would be recommended for video-editing or transcoding to blu-ray?

  - by Rob

  I'm looking for a machine (has to be a laptop) reasonably fast enough to handle editing/transcoding/rendering to Blu-ray disc of full true HD 1080p (1920x1080) video from a Samsung R10 camcorder - MPEG4 25fps (not the Sony-Panasonic AVCHD format): To be able to browse through the footage (say, quarter screen is fine for monitoring) and do simple edits - cut out bad bits, add titles, fades, nothing too fancy To be able to burn the footage in 1920x1080p 24p (twenty-four) fps to blu-ray, probably don't mind if I have to leave it for a few hours, or even overnight, as long as its not still running in the morning or takes days. I ALREADY have an external USB 2.0 LG BE06LU10 blu-ray burner. Does quad core make much difference? Or would Dual-core suffice for the above? NVidia because of CUDA for increased speed. What software today can take advantage of this? Which graphics card do I need? So far I've found Dell/Alienware to be well-specified, having a 5yr old Dell laptop that still runs well, albeit slow by today's standards, gives me a good impression. My concerns are too much fan-noise and budget and some Dell Precision Laptops exceed 1500 pounds. Thoughts?

  Read the article

< Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >