Search Results

Search found 18860 results on 755 pages for 'enigma machine'.

Page 214/755 | < Previous Page | 210 211 212 213 214 215 216 217 218 219 220 221  | Next Page >

• Ubuntu cannot access internet, LAN is fine

  - by Kevin Southworth

  I have an Ubuntu 8.04 LTS server that is directly connected to our Comcast Business Gateway modem and I have configured it with 1 of our 5 allotted Static IPs. My other machines on our LAN can connect to this server (via ssh, web, ping, etc.) but I cannot access this server from outside our network, and this machine cannot get out to the internet either (ping google.com fails with unknown host). Here is my /etc/networking/interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 173.162.54.19 netmask 255.255.255.248 broadcast 173.162.54.23 gateway 173.162.54.22 and my /etc/resolv.conf: nameserver 68.87.77.130 nameserver 68.87.72.130 output from sudo route -n: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 173.162.54.16 0.0.0.0 255.255.255.248 U 0 0 0 eth0 0.0.0.0 173.162.54.22 0.0.0.0 UG 100 0 0 eth0 I have a Windows 2008 machine with an almost identical Static IP, static DNS setup and it works correctly, can access it within the LAN and also from public internet, the Windows machine and the Ubuntu machine are both directly connected to the Comcast Business Gateway. I have tried rebooting Ubuntu, rebooting my Comcast modem, but nothing seems to make it work. I'm an Ubuntu noob, is there some other config I need to apply to make this work? UPDATE: Yes I am able to ping my default gateway 173.162.54.22 output of iptables --list -n: Chain INPUT (policy DROP) target prot opt source destination ufw-before-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-input all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy DROP) target prot opt source destination ufw-before-forward all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-forward all -- 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT) target prot opt source destination ufw-before-output all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-output all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-after-forward (1 references) target prot opt source destination LOG all -- 0.0.0.0/0 0.0.0.0/0 limit: avg 3/min burst 10 LOG flags 0 level 4 prefix `[UFW BLOCK FORWARD]: ' RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-after-input (1 references) target prot opt source destination RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:137 RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:138 RETURN tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:139 RETURN tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:445 RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:67 RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:68 LOG all -- 0.0.0.0/0 0.0.0.0/0 limit: avg 3/min burst 10 LOG flags 0 level 4 prefix `[UFW BLOCK INPUT]: ' RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-after-output (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-forward (1 references) target prot opt source destination ufw-user-forward all -- 0.0.0.0/0 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-input (1 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ctstate RELATED,ESTABLISHED DROP all -- 0.0.0.0/0 0.0.0.0/0 ctstate INVALID ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 3 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 4 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 11 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 12 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp spt:67 dpt:68 ufw-not-local all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 224.0.0.0/4 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 224.0.0.0/4 ufw-user-input all -- 0.0.0.0/0 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-output (1 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW,RELATED,ESTABLISHED ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW,RELATED,ESTABLISHED ufw-user-output all -- 0.0.0.0/0 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-not-local (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 ADDRTYPE match dst-type LOCAL RETURN all -- 0.0.0.0/0 0.0.0.0/0 ADDRTYPE match dst-type MULTICAST RETURN all -- 0.0.0.0/0 0.0.0.0/0 ADDRTYPE match dst-type BROADCAST LOG all -- 0.0.0.0/0 0.0.0.0/0 limit: avg 3/min burst 10 LOG flags 0 level 4 prefix `[UFW BLOCK NOT-TO-ME]: ' DROP all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-forward (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-input (1 references) target prot opt source destination ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:80 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:22 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-output (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0

  Read the article

• SSO solution and centralized user mgmt for about 10-30 Ubuntu machines?

  - by nbr

  Hello, I'm looking for a clean way to centralize user management. The setup: About 10-30 linux machines (Ubuntu 10.04 LTS server) Maybe 10-30 users for now. The requirements (hopes and expectations): A single place for the administrator to manage user accounts, passwords and the list of machines each user has access to. (And probably groups.) Doesn't have to be fancy. Single sign-on for SSH: the user should be able to login from machine A to machine B without re-entering his/her password. A Quick Google searches give me pointers to OpenLDAP and Kerberos, but I'm not sure where to start and what problem will each solution actually solve. Which way to go? I'd love to find a clear that focuses on this subject. (Or: am I asking "a wrong question"?)

  Read the article

• Is there a tool for mocking up iPad applications UI?

  - by thelearner

  I am in search of a tool which can be used to mock up iPad applications UI on a Windows machine.

  Read the article

• Linux - Block ssh users from accessing other machines on the network

  - by Sam

  I have set up a virtual machine on my network for uni project development. I have 6 team members and I don't want them to SSH in and start sniffing my network traffic. I already have set the firewall on my W7 pcs to ignore any connection attempts from the Virtual Machine, but would like to go a step further and not allow any network access from the VM to other machines on my network. Team members will be access the VM by SSH. The only external port forwarded is to vm:22. The VM is running in VirtualBox on a bridged network connection. Running latest Debian. If someone could tell me how to do this I would be much obliged.

  Read the article

• JAVA - multirow array

  - by user51447

  Here is my situation: a company has x number of employees and x number of machines. When someone is sick, the program have to give the best possible solution of people on the machines. But the employees can't work on every machine. I need a code for making little groups of possible solutions. this is a static example private int[][] arrayCompetenties={{0,0,1,0,1},{1,0,1,0,1},{1,1,0,0,1},{1,1,1,1,1},{0,0,0,0,1}}; = row is for the people and columns are for machines m1 m2 m3 m4 m5 m6 m7 p1 1 1 p2 1 1 1 1 p3 1 1 1 p4 1 1 1 p5 1 1 1 1 p6 1 1 1 1 p7 1 1 1 1 1 1 my question = with what code do i connect all the people to machine in groups (all the posibilities) like: p1 - m1 , p2-m2 , p3 - m3 , p4-m4 , p5 - m5 , p6-m6 p1 - m1 , p2-m3 , p3 - m3 , p4-m4 , p5 - m5 , p6-m6 p1 - m1 , p2-m4 , p3 - m5 , p4-m4 , p5 - m5 , p6-m6 p1 - m1 , p2-m5 , p3 - m3 , p4-m4 , p5 - m5 , p6-m6 p1 - m1 , p2-m2 , p3 - m3 , p4-m4 , p5 - m5 , p6-m6 .... i need a loop buth how? =D thanks!

  Read the article

• How to authorize standard users to install drivers

  - by Dr I

  I'm currently looking for a way to autorize my non administrators users to perform an installation of drivers. Here is the speech: All my users are standard users, they got a VirtualBox Hypervisor if they need the administrator rights. But if they put an USB device on the local machine and try to redirect the device to the Virtual Machine, Windows ask for some Administrator rights. I've try to set up those GPO: -Allow standard users to install drivers. -Install WHQL Drivers: Allow Silently. I don't know how to do this.

  Read the article

• Dual Boot Win8 and Win7 - Win 7 fails while booting

  - by bjan

  Below are my dual boot settings. Both are on different partitions, default is Windows 8. Both were working fine. There are multiple users of this machine, few run 8 while few 7. All 7's users are novice and they use Internet only. I frequently update Windows 8 but not 7. Few weeks ago, Win 7 stopped booting. Machine gets restarted while booting with 7(Windows 7 start up glowing-Win-logo-screen does not appear) and the 8's loader reappears. Win 7's partition still exists and contains Windows folder What steps should i take to check the problem?

  Read the article

• Xen P2V for large physical hosts with much free space

  - by Sirex

  I need to P2V a rhel5 machine to xen under rhel5. I know I can use dd if=/dev/sda then using virt-install --import on the host, but the downside of this is the original machine has 80% free space on its drive. Does anyone know of (or can document) a quick and easy method which works reliably, to produce a bootable xen image which can run under a hvm in such cases ? I tried clonezilla to make the image, to avoid the free space problem, but it failed to do the clone with "something went wrong" (useless info, i know). At the moment im looking at doing a dd of each partition, and a file level copy of the partition which is mostly empty, then creating a new virtual disk, copying the partitions over to it by mounting both the new image and the virtual drive on a second vm, then copying the boot sectors over, then copying the file level backup..... there must be an easier way ? Oh, and budget is $0. :)

  Read the article

• DD-WRT Router Can't hold a connection after initial setup...

  - by AC

  Struggeling with my new DDWRT router (Buffalo WZR-HP-G300NH) configuration. I configured it using one machine while comparing the settings on my existing Linksys WRT54GL on another machine. To the best of my knowledge, I've set it up the same way as my Linksys, but DDWRT has so many other options. After configuring it, I plugged it into the modem, VOIP device & my network. I see the phones come back online. However after a few minutes, it seems I lose the outbound connection (phones die and I can't get out over HTTP). What's confusing me is it works for a few minutes, then it fails. No idea what to look for. Ideas?

  Read the article

• switch duplicates packets and forward in two route

  - by sami

  there is a network including a router, two hosts and a switch which connects hosts to router. i have a virtual machine on my system. the network adapter is set to act as bridge. so the virtual machine and real OS are my 2 hosts on different LAN. they use one network card and are connected to a switch. when each of host send a packet to the other one, the switch duplicate the packet and forward it to both router and the other host. how can I solve the duplicate packet problem? Thanks.

  Read the article

• linux + automated rsync command

  - by Diana

  my target is to copy /tmp/my_file from 10.10.10.1 to my Linux machine without login and password , I set the passwords file with the right password - secret123 so rsync should work , please advice why I get Permission denied. Remark - 10.10.10.1 address is linux machine version – red hat 5.3 rsync -WavH --password-file=/tmp/passwords --progress [email protected]:/tmp/my_file . Permission denied. rsync: connection unexpectedly closed (0 bytes read so far) rsync error: error in rsync protocol data stream (code 12) at io.c(165) more /tmp/passwords secret123 ls -ltr passwords -rwxr-xr-x 1 root root 10 Sep 12 17:32 passwords

  Read the article

• how to remotely setup powershell to accept Enter-PSSession

  - by user1399195

  I have some computers I'm trying to remotely execute powershell commands but I'm running into some snags. For one thing, the computers do not have Enable-PSRemoting enabled so I am unable to simply Enter-PSSession. I tried to run a powershell script through psexec but I have yet to Set-Execution Policy on the machine. My thoughts were to execute a powershell logon script that accomplished this but before I tried this I was going to see if there were any other methods to enable-psremoting on a machine. Thanks in advance!

  Read the article

• Tunnel requests from remote server with ssh

  - by abronte

  I'm looking to forward requests from port 8003 on the remote machine to my localhost at port 8080

  Read the article

• Anything to share a printer from 32-bit to 64-bit Windows?

  - by marklam

  I've got a printer which only has 32-bit drivers, so it's installed on a 32-bit machine (XP). I need it to appear as a printer (with duplex control etc) on a 64-bit machine (Vista). I can't just share it using Windows printer sharing because the 64-bit client requires drivers to connect to it. There's no 64-bit driver for a similar printer that works (using the new port named \\server\printername). I've tried the ghostscript approach but that doesn't seem to help with the duplex control etc. Printeranywhere doesn't support 64-bit OS yet. Is there another way to do this?

  Read the article

• Connecting via ShrewSoft VPN client means no LAN internet access (Windows 7 64 bit) - any advice please?

  - by iwishiknewmoreaboutnetworking

  I have a Windows 7 64 bit desktop machine which is connected to a LAN. I recently installed ShrewSoft VPN client v 2.1.7 on my machine so that I can connect to a license server hosted by my customer. They are running a Cisco VPN server and I originally tried (unsuccessfully!) to use the Cisco VPN client for Windows 64 bit but the default gateway wasn't being configured correctly after loading in my pcf file. Using ShrewSoft I am able to import the same pcf file, and successfully connect to the machine I need to using the VPN client software. The client machine I need to connect to has IP address 1.52.90.33. The problem is that when I am connected to the customer network using the VPN client application (and after a few minutes) I lose my LAN internet connection. I can only presume that this is because, by default the ShrewSoft VPN client application automatically tunnels all traffic through the VPN connection. I know there is an option to switch off the "Tunnel All" option on the Policy tab of the application and enter a Remote Network Resource (to "Include" or "Exclude") as "Address" and "Netmask" IP addresses however I am not sure what I need to enter here. Here is my ipconfig output before connecting to the VPN (with suffixes blanked out): Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : ***.*** Link-local IPv6 Address . . . . . : fe80::8de3:9dbe:393a:33ba%11 IPv4 Address. . . . . . . . . . . : 150.237.13.17 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 150.237.13.1 Tunnel adapter 6TO4 Adapter: Connection-specific DNS Suffix . : ***.*** IPv6 Address. . . . . . . . . . . : 2002:96ed:d11::96ed:d11 Default Gateway . . . . . . . . . : 2002:c058:6301::c058:6301 Tunnel adapter Local Area Connection* 9: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:2cf9:38c4:6912:f2ee Link-local IPv6 Address . . . . . : fe80::2cf9:38c4:6912:f2ee%12 Default Gateway . . . . . . . . . : Tunnel adapter isatap.***.***: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : ***.*** Here is my route print output before connecting to the VPN: =========================================================================== Interface List 11...20 cf 30 9d ec 2a ......Realtek RTL8168D/8111D Family PCI-E Gigabit Ethern et NIC (NDIS 6.20) 1...........................Software Loopback Interface 1 14...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter 12...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 150.237.13.1 150.237.13.17 2 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 150.237.13.0 255.255.255.0 On-link 150.237.13.17 257 150.237.13.17 255.255.255.255 On-link 150.237.13.17 257 150.237.13.255 255.255.255.255 On-link 150.237.13.17 257 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 150.237.13.17 257 255.255.255.255 255.255.255.255 On-link 12

  Read the article

• USB flash module giving errors

  - by vshenoy

  Hi, I have a SATA USB flash module which was earlier running a 2.4 linux kernel (2.4.36.6) and on which now I am trying to install ubuntu server 10.04.1 LTS. I have two such USB flash modules and on one of them the installation process itself giving these errors: sd 4:0:0:0 [sda] Device not ready sd 4:0:0:0 [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE sd 4:0:0:0 [sda] Sense Key : Not Ready [current] sd 4:0:0:0 [sda] Add. Sense: Medium not present sd 4:0:0:0 [sda] CDB: Write(10): 2a 00 00 05 48 02 00 00 04 00 end_request: I/O error, dev sda, sector 46114 usb 1-1: reset high speed USB device using ehci_hcd and address 2 Buffer I/O error on device sda1, logical block 172033 lost page write due to I/O error on sda1 Buffer I/O error on device sda1, logical block 172034 lost page write due to I/O error on sda1 on the other the installation is successful, but after a day or two of running the machine hangs because of kernel spewing these messages: Remounting filesystem read-only EXT2-fs error (device sda1): read_block_bitmap: Cannot read block [bitmap - block_group = 105, block_bitmap = 860161] EXT2-fs error (device sda1): ext2_get_inode: unable to read inode block - inode=13083, block=24683 ext2_free_inode: bit already cleared for inode 83966 and the machine needs to be hard rebooted. On both the systems SCSI emulation with usb_storage driver is being used to detect the module. Here is the output of /proc/scsi/scsi on 2.4: # cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 02 and on 2.6: # cat /proc/scsi/scsi Attached devices: Host: scsi6 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 00 i.e. only 'ANSI SCSI revision:' is shown as different, although I am not sure if this can cause any problem. Really appreciate if someone can point as to how to debug this issue or any mailing list where I can further ask questions about this.

  Read the article

• External TV only allows 640x480 using VGA cable

  - by EdC

  I have Ubuntu precise installed on a MacBook Pro. When connecting to an external television using a VGA style cable the highest resolution available seems to be 640x480. I'm using the proprietary NVIDEA Accelerated Graphics Driver (version current) and attempting to setup the TV using the nvidea-settings tool. I know all the equipment supports higher resolutions because of the following: Prior to rebuilding my machine with precise, the same TV, cabel & adapter gave higher resolutions The same machine & TV when used with a HDMI cable allows higher resolutions Windows laptops with the same cable & TV are able to achieve higher resolutions I'm not sure what to look for next, there are some similar FAQ questions but I'm not sufficiently familiar with the areas involved to know if these are my issue or are safe to try. Specifically: colord problem & my monitor resolution 640*480 with no other options! - is the closest, but as I'm having no problems with the main laptop monitor I'm not sure the described symptoms apply. I can't work out from the answer or Bumblebee site how to determine if nvidia optimus applies to my laptop. Why isn't my monitor's native resolution appearing as an option? - suggests configuring X by hand, but doesn't entirely match the symptoms I'm seeing

  Read the article

• Can Remote Desktop Services be deployed and administered by PowerShell alone, without a Domain in WIndows Server 2012 and 2012 R2?

  - by Warren P

  Windows Server 2008 R2 allowed deployment of Terminal Server (Remote Desktop Services) without a domain, and without any insistence on domains. This was very useful, especially for standalone virtual or cloud deployments of a server that is managed remotely for a remote client who has no need or desire for any ActiveDirectory or Domain features. This has become steadily more and more difficult as Microsoft restricts its technologies further and further in each Windows release. With Windows Server 2012, configuring licensing for Remote Desktop Services, is more difficult when not on a domain, but possible still. With Windows Server 2012 R2 (at least in the preview) the barriers are now severe: The Add/Remove Roles and Features wizard in Windows Server 2012 R2 has a special RDS deployment mode that has a rule that says if you aren't on a domain you can't deploy. It tells you to create or join a domain first. This of course comes in direct conflict with the fact that an Active Directory domain controller should not be the same machine as a terminal server machine. So Microsoft's technology is not such much a Cloud Operating System as a Cluster of Unwanted Nodes, needed to support the one machine I actually WANT to deploy. This is gross, and so I am trying to find a workaround. However if you skip that wizard and just go check the checkboxes in the main Roles/Features wizard, you can deploy the features, but the UI is not there to configure them, and when you go back to the RDS configuration page on the roles wizard, you get a message saying you can not administer your Remote Desktop Services system when you are logged in as a Local-Computer Administrator, because although you have all admin priveleges you could have (in your workgroup based system), the RDS configuration UI will not accept those credentials and let you continue. My question in brief is, can I still somehow, obtain the following end result: I need to allow 10-20 users per system to have an RDS (TS) session. I do not need any of the fancy pants RDS options, unless Microsoft somehow depends on those features being present. I believe I need the "RDS Session Host" as this is the guts of "Terminal Server". Microsoft says it is "full Windows desktop for Remote Desktop Services client. I need to configure licensing so that the Grace Period does not expire leaving my RDS non functional, so this probably means I need a way to configure TS CALs. If all of the above could technically be done with the judicious use of the PowerShell, I am prepared to even consider developing all the PowerShell scripts I would need to do the above. I'm not asking someone to write that for me. What I'm asking is, does anyone know if there is a technical impediment to what I want to do above, other than the deliberate crippling of the 2012 R2 UI for Workgroup users? Would the underlying technologies all still work if I manipulate and control them from a PowerShell script? Obviously a 1 word Yes or No answer isn't that useful to anyone, so the question is really, yes or no, and why? In the case the answer is Yes, then how.

  Read the article

• Slow write speeds on new Gigabit home file server

  - by Ryan Holder

  So I finally got all my parts delivered to setup a home file/backup server this week. It's currently running Ubuntu Server and I'm using Samba to share files on my network. The server currently has a 2TB WD Green drive in it connected to a Asus M5A78L-M This is then connected via CAT6a to my new Gigabit switch (TP-Link TL-SG1005D). My home desktop is then also connected to this switch and again also through CAT6a cable. Currently when transfering files I will get a perfect 100MB/s read from the server to my Windows machine. When copying from my Windows machine to the server I get around 30/38MB/s. I know this drive is capable is faster speeds so would anybody have an idea of where the bottleneck is? Any help would be greatly appreciated :) EDIT: I have found ftp's write speed is much closer to what my Samba read speed is so I'm going to give it a guess that is a software problem rather than hardware

  Read the article

• Gathering IP address and workstation information; does it belong in a state class?

  - by p.campbell

  I'm writing an enterprisey utility that collects exception information and writes to the Windows Event Log, sends an email, etc. This utility class will be used by all applications in the corporation: web, BizTalk, Windows Services, etc. Currently this class: holds state given to it via public properties calls out to .NET Framework methods to gather information about runtime details. Included are call to various properties and methods from System.Environment, Reflection details, etc. This implementation has the benefit of allowing all those callers not to have to make these same calls themselves. This means less code for the caller to forget, screw up, etc. Should this state class (please what's the phrase I'm looking for [like DTO]?) know how to resolve/determine runtime details (like the IP address and machine name that it's running on)? It seems to me on second thought that it's meant to be a class that should hold state, and not know how to call out to the .NET Framework to find information. var myEx = new AppProblem{MachineName="Riker"}; //Will get "Riker 10.0.0.1" from property MachineLongDesc Console.WriteLine("full machine details: " + myEx.MachineLongDesc); public class AppProblem { public string MachineName{get;set;} public string MachineLongDesc{ get{ if(string.IsNullOrEmpty(this.MachineName) { this.MachineName = Environment.MachineName; } return this.MachineName + " " + GetCurrentIP(); } } private string GetCurrentIP() { return System.Net.Dns.GetHostEntry(this.MachineName) .AddressList.First().ToString(); } } This code was written by hand from memory, and presented for simplicity, trying to illustrate the concept.

  Read the article

• Multiple users writing to one Samba mount point in OSX

  - by Sam

  I have an OSX box containing a script which writes a unique file to a Samba share. The first part of the script mounts the share. On the machine are 2 users- UserA and UserB. Each requires to run this script at any given time however only the user who mounted the share is able to write to it. I really need both users to have rwx access. Here is what I have tried: Mounting then chmod'ing the mountpoint (no effect- overruled by Samba server?) chmod'ing the mountpoint then mounting (same as above) sudo mount_smbfs Both users have admin privileges. Ideally a solution would be executable by one of the users (contained in the script) and not rely on mounting at machine boot time. Any ideas appreciated, thanks!

  Read the article

• Grant user from one domain permissions to shared folder in another domain

  - by w128

  I have two computers set up like this: \\myPC (local Windows 7 SP1 machine); it is in domain1; \\remotePC (Win Server 2008 with SQL Server - a HyperV virtual machine); it is in domain2. In domain2 active directory, I have a user account RemoteAccount. I would like to give this account full permissions to a shared folder located on \\myPC, i.e. folder \\myPC\SharedFolder. The problem is, when I right-click the folder and go to sharing permissions, I can't add permissions for the domain2\RemoteAccount user, because this user cannot be found - I can only see domain1 users. When I click 'Locations' in "Select users, computers, service accounts, or groups" dialog, I only see domain1. Is there a way to do this?

  Read the article

• A proper way to create non-interactive accounts?

  - by AndreyT

  In order to use password-protected file sharing in a basic home network I want to create a number of non-interactive user accounts on a Windows 8 Pro machine in addition to the existing set of interactive accounts. The users that corresponds to those extra accounts will not use this machine interactively, so I don't want their accounts to be available for logon and I don't want their names to appear on welcome screen. In older versions of Windows Pro (up to Windows 7) I did this by first creating the accounts as members of "Users" group, and then including them into "Deny logon locally" list in Local Security Policy settings. This always had the desired effect. However, my question is whether this is the right/best way to do it. The reason I'm asking is that even though this method works in Windows 8 Pro as well, it has one little quirk: interactive users from "User" group are still able to see these extra user names when they go to the Metro screen and hit their own user name in the top-right corner (i.e. open "Sign out/Lock" menu). The command list that drops out contains "Sign out" and "Lock" commands as well as the names of other users (for "switch user" functionality). For some reason that list includes the extra users from "Deny logon locally" list. It is interesting to note that this happens when the current user belongs to "Users" group, but it does not happen when the current user is from "Administrators". For example, let's say I have three accounts on the machine: "Administrator" (from "Administrators", can logon locally), "A" (from "Users", can logon locally), "B" (from "Users", denied logon locally). When "Administrator" is logged in, he can only see user "A" listed in his Metro "Sign out/Lock" menu, i.e. all works as it should. But when user "A" is logged in, he can see both "Administrator" and user "B" in his "Sign out/Lock" menu. Expectedly, in the above example trying to switch from user "A" to user "B" by hitting "B" in the menu does not work: Windows jumps to welcome screen that lists only "Administrator" and "A". Anyway, on the surface this appears to be an interface-level bug in Windows 8. However, I'm wondering if going through "Deny logon locally" setting is the right way to do it in Windows 8. Is there any other way to create a hidden non-interactive user account?

  Read the article

• How To Cancel Pending Windows 7 Updates

  - by Itai

  How To Cancel Pending Windows 7 Updates? The key is pending. The shutdown button has the windows update symbol meaning that there are updates that were selected to be installed which were download and will be installed upon shutdown. The only thing is that my machine will no longer boot if I let it install those updates! They are incompatible with a driver needed in the system and I did not found out until too late. The system admin used a recovery disk to get back to the previous restore point, only the updates are now pending, so I need to cancel those before the machine shutdowns next.

  Read the article

• Account not getting completed deleted within linux

  - by lbanz

  I've got a nas box running some flavour of linux 2.6.31.8.nv+v2 with an arm processor. It has got a samba share called 'all' that has full read write access to everyone. However one Windows machine cannot access it without prompting for authentication and I found out from the logs that the windows account matches a local account on the nas box. What I then went to do is delete the local account on the nas. I can see that /home,/etc/password + /etc/shadow the account doesn't exist anymore. However the samba logs, shows that it thinks it is still there as it says account is disabled. I've tried rebooting both nas + windows box. Is there somewhere else that it stores account information? I logged on with a different account on that Windows machine and I can access the share fine. The smb logs shows that it can't find the user and then allows anonymous access.

  Read the article

< Previous Page | 210 211 212 213 214 215 216 217 218 219 220 221  | Next Page >