Search Results

Search found 8238 results on 330 pages for 'dynamic disks'.

Page 218/330 | < Previous Page | 214 215 216 217 218 219 220 221 222 223 224 225  | Next Page >

• AHCI, Windows 7 and can only boot with Windows DVD present

  - by Rob Pridham

  Foolishly, I installed Windows 7 with my new SSD set to IDE. I would like to change it to AHCI. I have done this before, with a different motherboard. What happens: I set the controller to AHCI in the BIOS; I also check correct boot order On boot, I get the 'BOOTMGR not found' error I use the Windows Recovery Console on the DVD Diskpart etc can see the disks, and bootrec claims to have rewritten the MBR/bootloader I reboot, same problem Recovery Console again and it detects a problem, fixes, reboots Recovery Console again and it detects the OS, and a problem - fixes, reboots I ignore the 'press any key to boot from DVD' prompt Windows boots fine I restart without the DVD and I'm back to square one That optional 'press a key to boot from DVD' stage is something that the recovery process introduces - normally you have to choose to boot to the DVD at the BIOS stage. You also see this when installing Windows. I suspect that whatever temporary state that is is compatible with AHCI - but not the standard it returns to. I have done the msahci/iaStorV registry hacks to no avail (this worked with the previous board). I can put it back to IDE where normal service is resumed. The board is an Asus M5A99X, the southbridge is AMD SB950, and this is Windows 7 x64. I would quite like not to have to reinstall it again. Any ideas as to what I can do as a permanent fix?

  Read the article

• How to share my localhost over the internet?

  - by Loolooii

  I really want to share my localhost over the internet to show my friends the progress of the website we're working on, so that I don't need to upload it to the public server each time I make a change. showoff.io is not free and localtunnel gives me "failed to authenticate" when trying to upload my public key (a lot of people seem to have this problem and there doesn't seem to be a solution for this). Does anyone know any other free service I can use or any other solution at all? I'm using a Mac. Thanks. UPDATE: with localhost I mean a web server running on my computer, I have a dynamic IP address and no I'm not behind a router (just using a wireless modem).

  Read the article

• Linux Software RAID1: How to boot after (physically) removing /dev/sda? (LVM, mdadm, Grub2)

  - by flight

  A server set up with Debian 6.0/squeeze. During the squeeze installation, I configured the two 500GB SATA disks (/dev/sda and /dev/sdb) as a RAID1 (managed with mdadm). The RAID keeps a 500 GB LVM volume group (vg0). In the volume group, there's a single logical volume (lv0). vg0-lv0 is formatted with extfs3 and mounted as root partition (no dedicated /boot partition). The system boots using GRUB2. In normal use, the systems boots fine. Also, when I tried and removed the second SATA drive (/dev/sdb) after a shutdown, the system came up without problem, and after reconnecting the drive, I was able to --re-add /dev/sdb1 to the RAID array. But: After removing the first SATA drive (/dev/sda), the system won't boot any more! A GRUB welcome message shows up for a second, then the system reboots. I tried to install GRUB2 manually on /dev/sdb ("grub-install /dev/sdb"), but that doesn't help. Appearently squeeze fails to set up GRUB2 to launch from the second disk when the first disk is removed, which seems to be quite an essential feature when running this kind of Software RAID1, isn't it? At the moment, I'm lost whether this is a problem with GRUB2, with LVM or with the RAID setup. Any hints?

  Read the article

• Nginx proxy to Apache - resolve HTTP ORIGIN

  - by Fratyr

  I have a server setup with nginx serving static content and proxy all PHP/dynamic requests to apache on 127.0.0.1 I'm building an API for my databases, and I need to allow clients by their origin (domain name), rather than just IP. Based on CORS rules. So when I send an HTTP header header("Access-Control-Allow-Origin: www.client-requesting.myapi.com"); from my API server, I have to tell it which origin I allow, otherwise client side requests won't work to my API due to same-origin policy. The question is how can I know which domain name (if any) called my API? What should be the nginx and apache configuration to pass the origin parameter? I tried to google, and all I found is some possible solution with mod_rpaf, but I wanted to be sure. Thanks!

  Read the article

• Removing a device in "removed" state from Linux software RAID array

  - by Sahasranaman MS

  My workstation has two disks(/dev/sd[ab]), both with similar partitioning. /dev/sdb failed, and cat /proc/mdstat stopped showing the second sdb partition. I ran mdadm --fail and mdadm --remove for all partitions from the failed disk on the arrays that use them, although all such commands failed with mdadm: set device faulty failed for /dev/sdb2: No such device mdadm: hot remove failed for /dev/sdb2: No such device or address Then I hot swapped the failed disk, partitioned the new disk and added the partitions to the respective arrays. All arrays got rebuilt properly except one, because in /dev/md2, the failed disk doesn't seem to have been removed from the array properly. Because of this, the new partition keeps getting added as a spare to the partition, and its status remains degraded. Here's what mdadm --detail /dev/md2 shows: [root@ldmohanr ~]# mdadm --detail /dev/md2 /dev/md2: Version : 1.1 Creation Time : Tue Dec 27 22:55:14 2011 Raid Level : raid1 Array Size : 52427708 (50.00 GiB 53.69 GB) Used Dev Size : 52427708 (50.00 GiB 53.69 GB) Raid Devices : 2 Total Devices : 2 Persistence : Superblock is persistent Intent Bitmap : Internal Update Time : Fri Nov 23 14:59:56 2012 State : active, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Name : ldmohanr.net:2 (local to host ldmohanr.net) UUID : 4483f95d:e485207a:b43c9af2:c37c6df1 Events : 5912611 Number Major Minor RaidDevice State 0 8 2 0 active sync /dev/sda2 1 0 0 1 removed 2 8 18 - spare /dev/sdb2 To remove a disk, mdadm needs a device filename, which was /dev/sdb2 originally, but that no longer refers to device number 1. I need help with removing device number 1 with 'removed' status and making /dev/sdb2 active.

  Read the article

• Thunderbird is unable to find server in DHCP controlled network.

  - by Skizz

  I have a network which consists of linux server and a combination of WinXP, Win7 and linux clients. All the systems are given dynamic IP addresses by the router which connects them all together. The server hosts an IMAP mail server. On Win7 and WinXP Thunderbird can access the IMAP server without any problems. On the linux client, using the same IMAP parameters, Thunderbird is unable to connect to the server. How do I get Thunderbird to find the server? I'm not sure if this is a linux system configuration problem or a Thunderbird issue. Additional note: The linux client is running Gnome, the server has a series of Samba shares defined. In the client, doing Places-Connect to Server and selecting Windows Share and specifying the server name, the Samba share is mounted OK.

  Read the article

• Very slow loading pages with router

  - by user984621

  I bought new router - this one: http://www.tp-link.com/en/products/details/?model=TL-WR841ND and the problem is, that the loading pages is so slow, even sometimes the pages aren't loaded at all. Is the same, when I have on the Mac OS or Windows. Below are the informations from the router-admin section: LAN IP Address: 192.168.2.1 Subnet Mask: 255.255.255.0 WAN IP Address: 192.168.1.100 Dynamic IP Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.254 DNS Server: 89.203.178.2 , 10.14.2.1 How can I fix this problem? Is almost impossible to use the internet this way.

  Read the article

• web spidering/crawling, can i do it or just search engines?

  - by bboyreason

  i already had a question answered about web-scraping with wget. but as i read a little more, i realize i may be looking for a web-crawling program. particularly the part about web-crawlers being able to get specific data like links or, in my case, products. all of the products on my site have the following naming convention, website.com/uniqueAlphaNumericID.html as far as i know, no dynamic content generation is being used and only one page per one item in the above format. should i just be thinking about: wget website.com | grep *.html or should i be looking into spiders/crawlers?

  Read the article

• NTFS frequent corruption when writing many small files, index $I30 error

  - by david sedai

  I'm running Windows 7 Ultimate on a laptop with a 500G HDD, and had all partitions formatted as NTFS. I do a lot of programming and LaTeX typesetting, both of these involves a large amount of reading/writing/deleting to a lot of small files, such as C++ library headers or LaTeX packages. The problem is that frequently, when there is a large number of writing to files, the partition being written to often corrupts, the chkntfs e: returns dirty, where e: is the partition being written. I've re-formatted the drive, I've contacted the laptop manufacturer and had the HDD checked, the HDD is not faulty, there are no bad sectors, and I've tried a brand new HDD, to no avail, and the other partition on the same physical drive doesn't have this issue. I'm pretty sure that it's no hardware related. I've searched the Microsoft support pages, one page http://support.microsoft.com/kb/982018 provides an update for Advanced Format Disks, which I've already installed. The chkntfs log shows $130 index errors. I'm at a loss here. Can anyone help? Thanks in advance.

  Read the article

• Tunneling HTTPS traffic via a PUTTY/SSL tunnel with SOCKS

  - by ripper234

  I have configured a SOCKS ssh tunnel to a remote proxy, and set my Firefox to use localhost:<port> as a SOCKS proxy. My intention is to tunnel outgoing HTTP/S connections from my machine via a specific 3rd party server I own (on AWS). In my testing, HTTP UTLs are forwarded properly (e.g. when I access http://jsonip.com/ from my computer I do get the server's IP) However, whenever I try to reach an HTTPS address, I get this error: The proxy server is refusing connections How do I debug/fix it? My PUTTY tunnel config is simply (some random source port number + dynamic checked): P.S. I'm aware I might need to manually accept SSL certificates. The reason I'm doing this is to resolve problems using gmail as an outbound SMTP service.

  Read the article

• How to dynamically insert text from an external file in a Powerpoint slide?

  - by Xavier Nodet

  My goal is to ensure that the C++ code I insert in my presentation compiles correctly. I therefore thought I'd have each example in a separate file (so that I can compile it), and include the text from those files in the Powerpoint slides... I want this 'inclusion' to be dynamic, so that if I change the code in a file, the slides are automatically updated. Is it possible? Will I have to use LaTeX instead of Powerpoint? Any other suggestion about how to solve this problem? Thanks.

  Read the article

• Server slowdown

  - by Clinton Bosch

  I have a GWT application running on Tomcat on a cloud linux(Ubuntu) server, recently I released a new version of the application and suddenly my server response times have gone from 500ms average to 15s average. I have run every monitoring tool I know. iostat says my disks are 0.03% utilised mysqltuner.pl says I am OK other see below top says my processor is 99% idle and load average: 0.20, 0.31, 0.33 memory usage is 50% (-/+ buffers/cache: 3997 3974) mysqltuner output [OK] Logged in using credentials from debian maintenance account. -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.63-0ubuntu0.10.04.1-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 370M (Tables: 52) [--] Data in InnoDB tables: 697M (Tables: 1749) [!!] Total fragmented tables: 1754 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 19h 25m 41s (1M q [28.122 qps], 1K conn, TX: 2B, RX: 1B) [--] Reads / Writes: 98% / 2% [--] Total buffers: 1.0G global + 2.7M per thread (500 max threads) [OK] Maximum possible memory usage: 2.4G (30% of installed RAM) [OK] Slow queries: 0% (1/1M) [OK] Highest usage of available connections: 34% (173/500) [OK] Key buffer size / total MyISAM indexes: 16.0M/279.0K [OK] Key buffer hit rate: 99.9% (50K cached / 40 reads) [OK] Query cache efficiency: 61.4% (844K cached / 1M selects) [!!] Query cache prunes per day: 553779 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 34K sorts) [OK] Temporary tables created on disk: 4% (4K on disk / 102K total) [OK] Thread cache hit rate: 84% (185 created / 1K connections) [!!] Table cache hit rate: 0% (256 open / 27K opened) [OK] Open file limit used: 0% (20/2K) [OK] Table locks acquired immediately: 100% (692K immediate / 692K locks) [OK] InnoDB data size / buffer pool: 697.2M/1.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 16M) table_cache (> 256)

  Read the article

• Two routers, one off-site, same ISP-assigned static IP. A recipe for conflict?

  - by boost

  This is the situation I've inherited: There are two routers, one off-site. Both are connected to the ISP. The ISP assigns both of them the same static IP (or so it seems). Presumably, the network problems we're having are related to the idea that you can't have two instances of the same IP. So we rang up the folk off-site and told them to turn off the router. Now everything's working okay here. How do I get around this? Get another static IP? Figure out how to get the router to ask for a dynamic IP (as we're not using the static IP for anything)?

  Read the article

• Virtual machine lost after power cut

  - by dannymcc

  We have just had a power issue and our ESX (ESXi 4.1.0) host lost power and then rebooted. All but one of the virtual servers have rebooted with no problem, however one of them refused to power up. I try to power it on and I get the following error: File <unspecified filename> was not found Reason: The system cannot find the file specified. Cannot open the disk '/vmfs/volumes/4e03076e-90834647-b846-001185c38f42/LAMP- Stack/turnkey-lamp-11.3-lucid-x86.vmdk' or one of the snapshot disks it depends on. VMware ESX cannot find the virtual disk "/vmfs/volumes/4e03076e-90834647-b846- 001185c38f42/LAMP-Stack/turnkey-lamp-11.3-lucid-x86.vmdk". Verify the path is valid and try again. I have logged into the ESX host to see if the file is there an have found only the following file that matches the filename: /vmfs/volumes/4e03076e-90834647-b846-001185c38f42/LAMP-Stack/turnkey-lamp-11.3-l ucid-x86-s001.vmdk I notice that the above file has '-s001' after the filename. Is this recoverable? Any help of advice is greatly appreciated! EDIT: Running ls -l on the directory that contains the file shows this: drwxr-xr-t 1 root root 1680 Feb 9 09:49 4e03076e-90834647-b846-001185c38f42 The databrowser file system looks like this: and in a different directory there is the file that matches the missing one:

  Read the article

• EC2 AMI won't boot after edit

  - by Eric Lars0n

  I did something stupid, I got a new laptop and copied everything over to the new one, then wiped the old one clean. Then I realized that I forgot to copy the private key out of .ssh that I use to connect to my AWS EBS backed instance. So I can't log in to my custom AMI. So I created a new Volume from the Snapshot of the AMI, then started up a public instance and attached the Volume to it, edit the sshd_config to allow for password log in. Unmounted the volume, detached it, made a snapshot of it, then made a new AMI from the snapshot. The new AMI launches, but never passes the Status Checks and is not reachable. What am I doing wrong? Or alternatively how can I fix my problem? Edit: Adding some of the console output Linux version 2.6.16-xenU ([email protected]) (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 SMP Mon May 28 03:41:49 SAST 2007 BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000006a400000 (usable) 980MB HIGHMEM available. 727MB LOWMEM available. NX (Execute Disable) protection: active IRQ lockup detection disabled RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize NET: Registered protocol family 2 Registering block device major 8 XENBUS: Timeout connecting to devices! Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,0)

  Read the article

• Computer does not boot, often

  - by tam

  I've ran into a issue with my computer that it does no longer reach POST, but simply powers on for a fraction of a second and powers off. But this is not always, some times it boots just normally and it works as it should, no issues with not enough power or anything. But as soon as I turn it of, I can not turn it back on, but then again at some random point it just powers up again, and resumes normal operation. If I disconnect the 8pin ATX connector from the motherboard, it powers up, fans and disks spinning normally until I power it off again. So this problem only happens when ATX is connected, which seems odd, I normally always saw this kind of an error if ATX was not connected, but here it's the exact opposite. It also does not emit any sound on the buzzer, except the normal beep, when it powers up normally. I have already tried: Remove graphics card Remove one and/or all RAM sticks Disconnect everything non-essential, even hard drives Clear CMOS I have not yet tried to remove all components and tried to boot everything outside of the case, because I did not have the time to disassemble and bleed the water loop. However, I can confirm that nothing is stuck underneath the motherboard, not is any of those brass raisers touching the board where it should not. Specs: Gigabyte GA-970A-UD3 AMD FX6300 ATI HD7850 I think this should be enough for this issue.

  Read the article

• Minimize VirtualBox Hard Drive disk

  - by Aviv

  I have Ubuntu Server 10.04 TLS installed on a Virtual Machine in a VirtualBox. The size of the Hard Drive is dynamic growing hard drive and the maximum is 32GB. At the beginning i had 4GB on the Hard Drive and the size of the .vdi was 4GB. Lately the size of data on the disk is 15GB but the size of the .vdi is almost 32GB. Why is that? How can i pack / optimize / defrag the HD so it will be the same size of the data on the disk? Thanks.

  Read the article

• OS X won't boot up unless I hold down option key

  - by Gazzer

  I have a strange issue on an early 2008 Mac Pro running OS 10.6: if I restart the computer it restarts normally if I shutdown and boot, it stops at the grey screen just before the boot process if I shutdown and boot but hold down the option key, I can select the boot disk and all is good. I've just cloned the disk, and the same thing happens. The disk is a SAMSUNG HD154UI The disk is partitioned (the second partition holds a clone of the Snow Leopard Install disk) One weird thing on the original disk was one of the partitions said 'EFI Boot' in a non-aliased font rather than the name of the disk when the disks are listed upon holding down option. Solution: it seems that there was a problem with the disk. Part of the difficulty in finding the solution was that you need to remove the disk from the computer completely. For example, a good disk in Bay 3, wouldn't boot up if the bad disk was in Bay 2. So for ages I thought the problem was hardware related in Bay 3. So if you think you have a dodgy disk remove it totally if you are testing the hardware with a 'clean' disk. Cleaning the PRAM helped to get the new disk to work too.

  Read the article

• Reverse Proxy (mod_rewrite) and Rails (absolute paths)

  - by SooDesuNe

  I have front end rails app, that reverse proxies to any of a number of backend rails apps depending on URL, for example http://www.my_host.com/app_one reverse proxies to http://www.remote_host_running_app_one.com such that a URL like http://www.my_host.com/app_one/users will display the contents of http://www.remote_host_running_app_one.com/users I have a large, and ever expanding number of backends, so they can not be explicitly listed anywhere other than a database. This is no problem for mod_rewrite using a prg:/ rewrite map reverse proxy. The question is, the urls returned by rails helpers have the form /controller/action making them absolute to the root. This is a problem for the page served by mod_rewrite because links on the proxied page appear as absolute to the domain. i.e.: http://www.my_host.com/app_one/controller/action has links that end up looking like /controller/action/ when they need to look like /app_one/controller/action mod_proxy_html seems like the right idea, but it doesn't seem to be as dynamic as I would need, since the rules need to be hard coded into the config files. Is there a way to fix this server-side, so that the links will be routed correctly?

  Read the article

• automated printouts from a wireless printer

  - by Piotr

  I have a wireless printer which is always on, and an always on fanless linux server. Looking at the mprinter project on Kickstarter I started to wonder if there is an app somewhere in the internet already that will allow to prepare an automated daily printout based on some settings. things to be printed could include - weather forecast for my locations, todo`s scheduled for that day, a "quote of a day" or "word of the day", stats from google analytics for my site, and many more ... I would set a printout at 6:15 every work day so its on my printer when I am already up, having a coffee. anyone knows something that can be used for such purpose? While I know this can be done by combining the power of TeX, cron and a script language to manage the dynamic part of the PDF I believe this is a use case someone has already addressed.

  Read the article

• How to change hybrid disk to basic disk in windows 7?

  - by Marco

  I created a partition E and then deleted the partition. After that I extended my partition C (where OS was installed) to take the space. My partition C became hybrid drive. My hp notebook does not have DVD rom and the notebook only came with an recovery image (I also have a paragon disc image). My computer has some problems now and I want to recover it by either the factory format or the paragon disc image. However, none of them works. I know it is because my disc has become hybrid disk. My question is how to fix the dynamic disk problem?

  Read the article

• Is there a way to automate testing for a GNS3 network topology?

  - by Chedy2149

  I'm working on an MPLS backbone topology using GNS3, this topology includes configuration of several networking technologies such as IPv6, BGP, OSPF, IPv6 to IPv4 dynamic tunneling, MPLS based VPNs, MPLS based traffic engineering... So I'm a beginner with basic knowledge in networking (Ipv4 addressing, basic routing and switching) and I can't just easly test if my topology works or not, moreover fiddling with configuration I've noticed that sometimes when getting MPLS config right and missing BGP config all my topology is messed up. Given that I use Cisco 7200 series routers, is there any way to build a test harness for my topology in order to guarentee correctness with a single push button automated process?

  Read the article

• How to setup RAID 1 with Intel RST on an existing Windows 7 system?

  - by instcode

  I'd like to setup RAID-1 using Intel Rapid Storage Technology on my Windows 7 64-bit system. I have an 1TB SATA HDD with Windows 7 system installed on the first primary partition (leftmost, ~200GB). The rest of this HDD is unallocated (~800GB). I bought another 2TB SATA, then created a primary partition (leftmost, ~500GB) and filled my data in. The rest of this HDD is unallocated (~1.5TB). A quick disk layout (XXX is the unallocated region): HDD1 (1TB): [ 200GB C:\ SYSTEM | XXXXXXXXXXXX ] HDD2 (2TB): [ 500GB Z:\ PROGRAM | XXXXXXXXXXXXXXXXXXXXXX ] Now, I want to create a 500GB RAID-1 partition (I'm not sure if using "partition" is correct here) on the rightmost of the 2 HDDs above without losing any existing data from both disks. Here is the expected layout: HDD1 (1TB): [ 200GB C:\ SYSTEM | XXXXXX | 500GB D:\ DATA - RAID-1 ] HDD2 (2TB): [ 500GB Z:\ PROGRAM | XXXXXXXXXXXXXXXX | 500GB D:\ DATA RAID-1] Let's not concern about data lost, is it possible to have that final layout using Intel RST? Previously, I tried this layout using dynamic disk & software RAID from Windows and it worked as expected, however, it's quite ugly in resynching after an OS failure that I don't want. If yes, is there a way to keep the data on existing partitions untouched or, at least, it should keep the SYSTEM partition safe (I'm okay if the PROGRAM partition has to be gone.)? Well, are there any strict/special steps I should follow when using the Intel RST manager in order to achieve that? If none of those questions above are "Yes", could you please suggest some other possible layouts that leave the C:SYSTEM partition untouched?

  Read the article

• How to make a server check it's own availability on the web?

  - by Javawag

  Hi all, Just a quick question – my server is running at my house serving www pages at www.javawag.com. The problem is that my home internet connection keeps dropping randomly - for about 10 mins at a time. This is only an intermittent problem and will go away soon I hope. However, my server doesn't recover properly - when the connection comes back, I can still access it at 192.168.0.8 (locally) without any issue, but at www.javawag.com there's no reply! (Just an aside - my home internet connection is dynamic ISP, the domain www.javawag.com points to javawag.dyndns.org which in turn points to my IP, updated every minute by ddclient on the server) Is there some way for the server to check if it's accessible from the outside world periodically, and if not restart Apache/reboot? Oh, and if I reboot the problem fixes itself also! Javawag

  Read the article

• How do I turn off caching in IIS7?

  - by jammus

  Hello. I'm developing an ASP classic site under Windows 7 (form a queue ladies). The problem is IIS seems to be heavily making use of its cache for both static and dynamic content which really conflicts with my 'make a small change, alt-tab, hit ctrl-F5' development style. Changes made to .asp files may take two or three refreshes to show up where as changes to .js files can take 20 times as many. How do I go about turning the caching off on my development machine? Cheers. in b4 stop using asp classic

  Read the article

< Previous Page | 214 215 216 217 218 219 220 221 222 223 224 225  | Next Page >