Search Results

Search found 11524 results on 461 pages for 'insurance networking news'.

Page 221/461 | < Previous Page | 217 218 219 220 221 222 223 224 225 226 227 228  | Next Page >

  • How to connect Android phone to a Wifi network using PPPoE?

    - by Slavo
    I have an ISP at home, which provides me with a PPPoE connection. My router supports that and I've configured it to autoconnect periodically, so I don't have to type my username and password each time. When I connect to the Wireless router from the PC, I have internet and everything works fine. However, when I do so using my Android phone, there's no internet connection on the phone. It connects to the router, but I cannot open any web page. How can I enable internet access from such an ISP on my phone? Is it something in the router setup? The router is Linksys WRT54GL.

    Read the article

  • Odd internet packet routing

    - by NachoChip
    I want to know is there anyway to explicitly control the packet routing. I try to connect my computer in HK from San Francisco. It is extremely slow and I use tracert to see what is going on. It seems the packet get routed from HK to Europe and then to New York and then to San Francisco. In US, I am using Astound Cable. Is there any suggestion I can force the packet to not go around the world before it reach my computer? Or it is all ISP dependent?

    Read the article

  • Keep source IP after NAT

    - by John Miller
    Until today I used a cheapy router so I can share my internet connection and keep a webserver online too, while using NAT. Users IP ($_SERVER['REMOTE_ADDR']) was fine, I was seeing class A IPs of users. But as traffic grown up everyday, I had to install a Linux Server (Debian) to share my Internet Connection, because my old router couldn't keep the traffic anymore. I shared the internet via IPTABLES using NAT, but now, after forwarding port 80 to my webserver, now instead of seeing real users IP, I see my Gateway IP (Linux Internal IP) as any user IP Address. How to solve this issue? I edited my post, so I can paste the rules I'm currently using. #!/bin/sh #I made a script to set the rules #I flush everything here. iptables --flush iptables --table nat --flush iptables --delete-chain iptables --table nat --delete-chain iptables -F iptables -X # I drop everything as a general rule, but this is disabled under testing # iptables -P INPUT DROP # iptables -P OUTPUT DROP # these are the loopback rules iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT # here I set the SSH port rules, so I can connect to my server iptables -A INPUT -p tcp --sport 513:65535 --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --sport 22 --dport 513:65535 -m state --state ESTABLISHED -j ACCEPT # These are the forwards for 80 port iptables -t nat -A PREROUTING -p tcp -s 0/0 -d xx.xx.xx.xx --dport 80 -j DNAT --to 192.168.42.3:80 iptables -t nat -A POSTROUTING -o eth0 -d xx.xx.xx.xx -j SNAT --to-source 192.168.42.3 iptables -A FORWARD -p tcp -s 192.168.42.3 --sport 80 -j ACCEPT # These are the forwards for bind/dns iptables -t nat -A PREROUTING -p udp -s 0/0 -d xx.xx.xx.xx --dport 53 -j DNAT --to 192.168.42.3:53 iptables -t nat -A POSTROUTING -o eth0 -d xx.xx.xx.xx -j SNAT --to-source 192.168.42.3 iptables -A FORWARD -p udp -s 192.168.42.3 --sport 53 -j ACCEPT # And these are the rules so I can share my internet connection iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -A FORWARD -i eth0:1 -j ACCEPT If I delete the MASQUERADE part, I see my real IP while echoing it with PHP, but I don't have internet. How to do, to have internet and see my real IP while ports are forwarded too? ** xx.xx.xx.xx - is my public IP. I hid it for security reasons.

    Read the article

  • Servers / ram for social network- how many?

    - by Marty
    I am launching my social network soon an looking into hosting. The question i am lost is: Do i need separate servers for web vs database vs image handling since there is photo sharing? Or does 1 server handle it all? Also is more ram better? If i get 50GB ram is that better than having 8 gb ram? EDIT: It is PHP codeignitor and MySQL for now. (switch to NoSQL DB later if demand calls fr it.) I will be using memcache also. Concept wise it is similar to yelp, so geographic based with lots of user content and image sharing + live feeds an privacy levels. User plan is open question. Without testing the demand for this i cant give a number. But the concept is unique, no one out there with the set of features i am releasing so it could grow. Ideally I want to plan for handling about 1-2 million views / month from launch. If it goes more than that then I will upgrade.

    Read the article

  • How to set up my network/bridging using Apple Airport equipment?

    - by John
    I'd like to set up my network like this, and I want to make sure it's possible using the hardware I have. I think it should be... I've got my cable modem in one room. I want to plug it into an Apple Airport Express and create my wireless my wireless network here. The airport express will do the NAT and DHCP. By my TV there are a few things to be networked (Xbox and Tivo). I have an airport extreme here. I'd like to have the airport extreme join the wireless network and share the connection to the ethernet ports. Can anyone provide some assistance on the best way to configure to do this? Thanks!

    Read the article

  • using wireless with VMWare workstation 6.5

    - by BdotA
    I am using VMWare workstation 6.5 and have installed WinXP SP2 on it. My main operation system is Win 7. when I am hard-wired, I can use internet inside vmware but when I am wireless, I cannot use internet inside vmware... I did a research and found that the network adapter should be on NAT instead of bridge, I tried that but it did not work either.

    Read the article

  • My network manager stop running very shotly when installed VirtualBox-4.0, reporting network manager not running

    - by wangolo joel
    I fell into a snare when i downloaded and install virtual box 4.0 on my ubuntu 10.4, when i started the virtualbox i tried i saw that my network icon on my desktop showed my red x showing iam disconnected and this happened shortily when i installed virtual box 4.0 I have searched through the web and found some people who have faced some problem. but the solution they gave them i tried but it coudn't work, of restarting,starting ,stoping the netowrk manager, i was even thinking of uninstalling this virutalbox but not netowrk connection truely i need your help

    Read the article

  • Small office network setups

    - by user39822
    I work at a small office and we're overhauling our network setup there. We're a web dev company and at the moment we have 50+ production sites running on the same machine that runs our internal email, which is just plain stupid. We're moving all our client hosting off site and are now looking for something to run our internal office requirement. Below is a brain dump: Equal amount of Mac & PC, about 25 machines in total. We need a central "server" to host files that should be accessible everyone as a "network drive". If possible we'd like to use low cost hardware for this (Mac or Win based). Disk space should be upward of 1TB. Ideally we should also be able to run a small web server on this machine (LAMP stack) to run some planning and billing applications we wrote ourselves. We need some sort of MS Exchange alternative for things like a shared calendar and especially being able to set Out of Office replies. We have one printer that is connected to the network Setup should be something can preferably be managed easily via a graphical interface and NOT require command line skills. Users want to keep using Apple Mail or MS Outlook After a quick google I came across the Zimbra collaboration suite, can anyone recommend this or any other solution for our office?

    Read the article

  • Routing application traffic through specific interface

    - by UnicornsAndRainbows
    Hello All! First question here, so please go easy: I have a debian linux 5.0 server with two public interfaces. I would like to route outbound traffic from one instance of an application via one interface and the second instance through the second interface. There are some challenges: both instances of the application use the same protocol both instances of the application can access the entire internet (can't route based on dest network) I can't change the code of the application I don't think a typical approach to load balancing all traffic is going to work well, because there are relatively few destination servers being accessed in the outbound traffic, and all traffic would really need to be distributed pretty evenly across these relatively few servers. I could probably run two virtualized servers on the box and bind each of them to a different external ip, but I'm looking for a simpler solution, maybe using iproute or iptables? Any ideas for me? Thanks in advance - and I'm happy to answer any questions.

    Read the article

  • how do i automatically add a new route to the routing table?

    - by Robbie Mckennie
    I'm looking at linking two networks with a long range Ethernet bridge. I know I can connect my two networks with a router, but my problem is how will my computers know where to send packets if I don't add the route manually? I COULD add them manually, but it seems like a hassle. I have very very limited knowledge of RIP (I know it has something to do with routing), but I don't know how to use it. edit: My vision for the network would be the 2 networks (which are currently independent home networks), connected by a microwave Ethernet link. I assumed i'd need a router on one end of the bridge, to handle communication between the 2 networks.

    Read the article

  • TCPDump and IPTables DROP by string

    - by Tiffany Walker
    by using tcpdump -nlASX -s 0 -vvv port 80 I get something like: 14:58:55.121160 IP (tos 0x0, ttl 64, id 49764, offset 0, flags [DF], proto TCP (6), length 1480) 206.72.206.58.http > 2.187.196.7.4624: Flags [.], cksum 0x6900 (incorrect -> 0xcd18), seq 1672149449:1672150889, ack 4202197968, win 15340, length 1440 0x0000: 4500 05c8 c264 4000 4006 0f86 ce48 ce3a E....d@[email protected].: 0x0010: 02bb c407 0050 1210 63aa f9c9 fa78 73d0 .....P..c....xs. 0x0020: 5010 3bec 6900 0000 0f29 95cc fac4 2854 P.;.i....)....(T 0x0030: c0e7 3384 e89a 74fa 8d8c a069 f93f fc40 ..3...t....i.?.@ 0x0040: 1561 af61 1cf3 0d9c 3460 aa23 0b54 aac0 .a.a....4`.#.T.. 0x0050: 5090 ced1 b7bf 8857 c476 e1c0 8814 81ed P......W.v...... 0x0060: 9e85 87e8 d693 b637 bd3a 56ef c5fa 77e8 .......7.:V...w. 0x0070: 3035 743a 283e 89c7 ced8 c7c1 cff9 6ca3 05t:(>........l. 0x0080: 5f3f 0162 ebf1 419e c410 7180 7cd0 29e1 _?.b..A...q.|.). 0x0090: fec9 c708 0f01 9b2f a96b 20fe b95a 31cf ......./.k...Z1. 0x00a0: 8166 3612 bac9 4e8d 7087 4974 0063 1270 .f6...N.p.It.c.p What do I pull to use IPTables to block via string. Or is there a better way to block attacks that have something in common? Question is: Can I pick any piece from that IP packet and call it a string? iptables -A INPUT -m string --alog bm --string attack_string -j DROP In other words: In some cases I can ban with TTL=xxx and use that should an attack have the same TTL. Sure it will block some legit packets but if it means keeping the box up it works till the attack goes away but I would like to LEARN how to FIND other common things in a packet to block with IPTables

    Read the article

  • Improve wireless performance

    - by djechelon
    Hello, I have a Trust Speedshare Turbo Pro router, which is running on channel 6. I found that the wireless signal (and network performance) dramatically drops from my PDA (I can barely attach to the network, even if I set the PDA's energy settings to maximum wireless performance) when I even exit my room, and I don't have shielded walls or something like that. I can't even stream a SD video from my desktop (connected via LAN) to my laptop using WiFi, while via LAN it works fine. I read that changing router's channel could improve performance due to interference reducing. I found that almost all wireless networks around here run on channels 6 and 11. I tried to go to my router's settings page to change channel, but I found that the combo box only allows me to select 6!! I'm not sure, but I may have been able in the past to change channel, though not to all of the available channels. A few minutes ago I tried a firmware upgrade, but it didn't solve my problem. My question is Is it possible that my router is someway locked to its channel? I bought it on my own, I didn't receive it from my ISP Apart from boosting the antenna power to the maximum (which, by the way, increases the EM radiation my and my family's bodies absorb 24/7 and is little more environment-unfriendly), do you have any tips on getting high quality transmission up to 5 metres from the antenna? Thank you

    Read the article

  • Setting a wireless access point on Ubuntu server 11.10

    - by Solignis
    I am trying to setup a wifi access point with my Ubuntu server. I have managed to get my phone to connect the wireless and now it get a DHCP lease. Though it still cannot ping out or get pinged by anything on my network. I am prety sure my problem is iptables, but I not sure what would be wrong. Here is what my rules look like. (The ones pertaining to the bridge interface) # Allow traffic to / from wireless bridge interface iptables -A INPUT -i br0 -j ACCEPT iptables -A OUTPUT -o br0 -j ACCEPT I am guessing my rules are a little lean, the bridge exists on the same subnet as everything else on my network, I am using a 10.0.0.0/24 subnet. EDIT Oh yeah I should mention also, when I do a ping test, I get Destination Host Unreachable as the error.

    Read the article

  • Add a netbook to an existing Windows XP home network

    - by GorillaSandwich
    I've got a home network set up with a couple of Windows XP computers. I'm now trying to add our new netbook to it - also running XP. (The goal is to share files and a printer.) I have run the Network Setup Wizard and made sure that the workgroup name is the same as the others, and have rebooted several times, but whenever I try to 'view workgroup computers,' the only one on it is the netbook. I have a Windows XP CD, but the netbook has no drive. The wizard has some options for floppy disks, but that's useless to me these days. What is this wizard actually trying to do, and can I do it manually? Surely it can't be this hard.

    Read the article

  • Watching Netflix through a VPN

    - by Sergio
    Recently I bought a VPS from DigitalOcean. I setup a PPTP VPN so I could watch us Netflix content from outside the US. Now that I have it setup and all my traffic is going through the VPN, Netflix is still showing my home country content. Pandora is working, and when I search my IP it shows im in NY, so I guess traffic is being routed correctly. I have also tried to delete flash settings and cookies from browser. Any ideas on what could be happening?

    Read the article

  • How do I network this Windows Failover Cluster and MongoDB Replica Set? (diagram inside)

    - by arex1337
    As you can see, my two Windows Server Failover Cluster (WSFC) nodes have three network interfaces each, which connects them to three different networks : A public network A private network consisting of the WSFC nodes A private network consisting of the WSFC nodes and a machine with the WSFC Quorum Witness File Share Does this network configuration I've planned, make sense? Do I have the "right" number of NICs and networks? I'm thinking the 2nd NIC/network may be unnecessary. My two MongoDB Replica Set nodes also have three network interfaces each - very similar to the previous situation: A public network A private network consisting of the primary and secondary MongoDB Replica Set nodes A private network consisting of the primary, secondary and arbiter MongoDB Replica Set nodes Does this network configuration, make sense? Do I have the "right" number of NICs and networks? I'm thinking the 2nd NIC/network may be unnecessary. Here is the simpler version I'm considering: UPDATE:

    Read the article

  • How to Solve the "Unidentified network" in Windows 7

    - by gylns
    I connect the internet through Ad-hoc network, My machine uses win7 and another uses winows xp, There's no problem when I connect the XP machine, but if i disconnect and reconnect the net, then my local network is marked as "Unidentified network",unless restart the XP machine, I don't know why?

    Read the article

  • Why PowerConnect and Juniper are so rare ? Why do enterprises stick with Cisco ?

    - by Kedare
    Hello ! I have a little question, I'm actually studing in IT in France, and when looking on alternative on the very [...] very expensive Cisco equipment, I've found Juniper and DELL PowerConnect pretty attractive on features and price, but I rarely see something else than the classics Cisco/LinkSys, HP Procurve and Netgear.. Why it's so rare to find those switch ? They looks really great but... I've never seen any Juniper or Powerconnect... Why do enterprises stick with the expensive Cisco ? I've tried to find how to buy both, it's quite easy with PowerConnect, everything is on the DELL website, but it looks it's very hard to find Juniper equipment in France :( Thank you !

    Read the article

  • Can't route specific subnet thru VPN in ubuntu

    - by Disco
    I'm having issues routing traffic thru VPN. Here's my setup I have 3 hosts, let's call them A, B and Z B and Z have a VPN connection in the 10.10.10.x SUBNET A and B have a direct connection in the 10.10.12.x SUBNET I want to be able to route traffic from A to Z, like : A <= 10.10.12.254 [LAN] 10.10.12.111 => B <= 10.10.10.152 [VPN] 10.10.10.10 => Z On host B, i have set up ip_forwarding : net.ipv4.ip_forward = 1 and routing on host B: [root@hostA: ~]# ip route 10.10.10.10 dev ppp0 proto kernel scope link src 10.10.10.152 10.10.12.0/24 dev eth1 proto kernel scope link src 10.10.12.111 10.10.10.0/24 dev ppp0 scope link 169.254.0.0/16 dev eth1 scope link routing on host A: [root@hostA: ~]# ip route 10.10.10.0 via 10.10.12.111 dev eth1 10.10.12.0/24 dev eth1 proto kernel scope link src 10.10.12.254 169.254.0.0/16 dev eth1 scope link default via 192.168.1.1 dev eth0 But still not able to ping 10.10.10.10 from host A. Any idea ? I'm pulling my hairs out.

    Read the article

  • I don't get any Internet when I connect connect Cisco DPC3825 DOCSIS 3.0 Gateway with DLink DIR-625 [on hold]

    - by Asif Akhtar
    I am using Cisco DPC3825 DOCSIS 3.0 Gateway as my modem and router right now and it works fine on a computer directly connected to Cisco DPC3825 DOCSIS 3.0 Gateway with wire but I am getting very low/poor signal strength on my wireless computer due to which I am looking to install DLink DIR-625 as my router but because when I connect Cisco DPC3825 DOCSIS 3.0 Gateway with DLink DIR-625 and connect my computer with wire to DIR-625 then I don’t get any Internet.(I get Internet when I connect my computer with wire with Cisco DPC3825 DOCSIS 3.0 and I know there is nothing wrong with DLink DIR-625).

    Read the article

  • ipv6 with KVM on debian

    - by Eliasdx
    I have trouble setting up IPV6 on my Proxmox (KVM) server: My ISP sent me this information(xxx=placeholder): IPs: 2a01:XXX:XXX:301:: /64 Gateway: 2a01:XXX:XXX:300::1 /59 This is the interface setup on the host server: auto vmbr1 iface vmbr1 inet static address 178.XX.XX.4 broadcast 178.XX.XX.63 netmask 255.255.255.192 pointopoint 178.XX.XX.1 gateway 178.XX.XX.1 bridge_ports eth0 bridge_stp off bridge_fd 0 iface vmbr1 inet6 static address 2a01:XXX:XXX:301::2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del 2a01:XXX:XXX:300::1 dev vmbr1 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev vmbr1 On the guest: auto eth0 iface eth0 inet static address 178.xx.xx.47 netmask 255.255.255.255 broadcast 178.xx.xx.63 gateway 178.xx.xx.1 pointopoint 178.xx.xx.1 iface eth0 inet6 static pre-up modprobe ipv6 address 2a01:XXX:XXX:301::2:2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del 2a01:XXX:XXX:300::1 dev eth0 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev eth0 Ipv4 works on both host and guest but Ipv6 only works "sometimes". It's up for minutes and then down again until I change something. However I can actually ping the host and the guest from both host and guest. host:~# ip -6 neigh 2a01:XXX:XXX:301::100:2 dev vmbr1 lladdr 00:50:56:00:00:e0 REACHABLE 2a01:XXX:XXX:300::1 dev vmbr1 lladdr 00:26:88:76:18:18 router STALE host:~# ip -6 route 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 2a01:XXX:XXX:301::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tap101i1d0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 Does someone know why it isn't working? And is there a way to configure multiple v6 IPs from the same subnet so I can dedicate IPs to websites on a server with multiple virtualhosts?

    Read the article

  • Windows VPN not authenticating from ADSL to Wireless link

    - by deanvz
    I have a normal windows VPN on a computer connecting to a 196.201.x.x/24 IP. If this VPN tries to connect from any address in the 41.x.x.x range it cant get there. The server is a normal windows 2008 server, running exchange with a PPPoE IP natted to a public IP on the public gateway of the wireless network as the server is on site and its connectivity is derived from Mikrotik RB's. The computer on the 41 range can traceroute and ping the server, but the VPN does not authenticate. When on the network or any other, the VPN works fine. Is there something that could be configured on the VPN client? All firewall settings of a standard ADSL router have been checked and found to block only ICMP's. Is this a VPN configuration problem or a network issue?

    Read the article

  • VMware server 2.0 SYN/ACK repeating issues

    - by user65579
    VMWare Server 2.0.0 Build 122956 I am having some issues with connecting into a guest VM (Ubuntu linux 4.4.3-4 lucid) running under VMware 2.0 on a windows server host. All connections to and from the VM's work fine, except for FTP. I thought the issue was the FTP daemon at first but it has been ruled out that it is not the daemon or the server itself. When you try to connect to the FTP server from outside of the host OS it fails with a "421 Service not available" but when you try and connect from the local VM or from the host OS the connection goes through fine. I have ran many packet sniffs using wireshark/tcpdump from the VM, the host OS, and the client connecting, the most informative is the host OS. I have attached a PNG of the relavant packets that were captured. I viewed some other network traffic that was sniffed (WWW specifically) and it seems to do the same syn/ack repeating but the user doesnt see any issues. I have disabled the firewall and the issues persisits, I have tried with specific allow rules to ensure the data is allowed and no changes. It appears like VMware attempts to do the ICMP redirect and it works, but then it vmware repeats the packets sent so you get 3 syn/ack's for every one syn from the client. Also VMWare appears to be attempting to establish an FTP connection between the HOST OS and the GUEST OS, because I see the second SYN sent from the HOST OS to the GUEST to initiate a new connection, and it get the appropriate SYN/ACK followed by an ACK, but the client never sees any of this from its end. EG. syn from client syn/ack from host OS to client syn/ack from guest OS to client syn/ack from host OS to client The same thing happens when the connection reset is attempted, RST's start being sent and repeated, the server responds with a valid header to continue the FTP handshake but the RST acknowledgement is allready issued and things are closed. I am not 100% if this is a bug in VMware or possibly a VMNetwork missconfiguration. Does anyone have any thoughts on where exactly the issue could be, things to try to verify or rule out? I have linked to a picture of the relevant packets sniffed from the host OS. http://img18.imageshack.us/img18/7789/vmwareftpconnection.jpg

    Read the article

< Previous Page | 217 218 219 220 221 222 223 224 225 226 227 228  | Next Page >