Search Results

Search found 5885 results on 236 pages for 'monitor'.

Page 222/236 | < Previous Page | 218 219 220 221 222 223 224 225 226 227 228 229  | Next Page >

  • what is the best mid/high-end class audio/music creation audio sound card?

    - by Chris
    Hello, I have a computershop myself, and I repair computers. But one of the things I really don't know (yet) is the performace od audio cards for music creation with midi. I have searched and searched and came up with some good reviews, but after browsing for a couple of hours I could't see the trees trough the forrest :-D (it's a dutch expression) At one moment I thought the M-Audio - Delta 1010LT would be a good PCIe card, later on I read that this card was released years ago. (but that could be false information) Also any personal expierence would be great, but not necessairy. I have searched a few cards, and I hope someone can help me make a choice for a friend of mine. He's buget is between $100 and $350 I know there are audio cards from $ 500 - $1850,- this is just too expensive. The following specs are crucial: ASIO Midi Mic in minimal 5.1, 7.1 recommended it's not for airplay, but just to compose music at home. using Ableton and midi keyboard. 1. M-Audio - Delta 1010LT: 8 x 8 analog I/O 2 mic preamps or line inputs S/PDIF digital I/O (coaxial) with 2-channel PCM SCMS copy protection control digital I/O supports surround-encoded AC-3 and DTS pass-through 1 x 1 MIDI I/O directly drive up to 7.1 surround (bass management software included) software controlled 36-bit internal DSP digital mixing/routing +4dbu/-10dBV operation individually switched in software word clock I/O for sample accurate device synchronization 2. RME HDSP 9632: * Stereo Analog Ein- und Ausgang, symmetrisch*, 24-Bit/192kHz, > 110 dB SNR * Optionale Erweiterungsboards mit je 4 symmetrischen Ein- und Ausgängen * Alle analogen I/Os voll 192 kHz-fähig, also keine Reduzierung der Kanalzahl * 1 x ADAT Digital In/Out, 96 kHz-fähig (S/MUX) * 1 x SPDIF Digital In/Out, 192 kHz-fähig * 1 x Breakout Kabel für koaxialen SPDIF-Betrieb* * Also bis zu 16 Ein-und Ausgänge gleichzeitig nutzbar! * 1 x Stereo Kopfhörerausgang, parallel zum analogen Ausgang, aber eigene Pegelanpassung * 1 x MIDI I/O für 16 Kanäle Hi-Speed MIDI über Breakout Kabel * DIGICheck, RMEs einzigartiges Meter- und Analysetool mit Spectral Analyser, Professionelle Level Meter 2/8/16-Kanalig, Vector Audio Scope und diversen weiteren Analysefunktionen * HDSP Meter Bridge: Frei skalierbare Levelmeter mit Peak- und RMS Berechnung in Hardware * TotalMix: 512-Kanal Mischer mit 40 Bit interner Auflösung 3. EMU 1212M (1212 M) PCIe: * Top kwaliteit convertors 24-bit/192kHz convertors. * Hardware gestuurde effecten. * DSP zero-latency hardware mixen en monitoring. * Analoge en digitale I/O plus MIDI. * EMU Production Tools Software Bundle - Cakewalk SONAR , Steinberg Cubase LE, Ableton Live E-MU Edition **EMU 1212M PCI-e inputs/outputs:** * 2 balanced jack inputs. * 2 balanced jack outputs. * 24-bit/192kHz ADAT I/O. * 24-bit/192kHz Coaxiale S/PDif I/O switchable to AES/EBU. * MIDI I/O. 4. M-Audio Audiophile 192: - Up to 24-bit/192kHz audio - 2 balanced analog inputs (1/4” TRS) - 2 balanced analog outputs (1/4” TRS) - S/PDIF digital I/O (coaxial RCA connectors) with 2-channel PCM - SCMS copy protection control - Digital I/O supports surround-encoded AC-3 and DTS pass-through - Direct hardware input monitoring via separate balanced 1/4” TRS monitor outputs - Software routing of inputs and outputs - Digital I/O can be routed to/from external effects - 16-channel MIDI I/O - ASIO, WDM, GSIF 2 and Core Audio driver support for compatibility with most applications - 64-bit driver support for Windows - PCI 2.2 compatibility - Apple G5 compatible - Incompatible exceptions - Includes Ableton Live Lite music production software, so you can make music right away - Works with other Delta cards Technical Specifcations: - Compatibility - ASIO - WDM - GSIF 2 - Core Audio

    Read the article

  • Application Does Not Start in Windows 7

    - by Jim Fell
    I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fresh from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried running sfc /scannow from the command line (with administrator privileges), shutting down the Spybot Resident, and disabling the firewall and virus scanner. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Faulting application name: SSDFresh.exe, version: 1.0.0.0, time stamp: 0x4f2a45d8 Faulting module name: unknown, version: 0.0.0.0, time stamp: 0x00000000 Exception code: 0xc0000005 Fault offset: 0x000007ff0016dbba Faulting process id: 0x994 Faulting application start time: 0x01cd11fd9fe978df Faulting application path: C:\Program Files (x86)\SSD Fresh\SSDFresh.exe Faulting module path: unknown Report Id: dfeed551-7df0-11e1-a2c7-002522c47ec0 Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Application: SSDFresh.exe Framework Version: v4.0.30319 Description: The process was terminated due to an unhandled exception. Exception Info: System.NullReferenceException Stack: at AbBugReporter.BugForm.InitLanguage() at AbBugReporter.BugForm..ctor(AbFlexTrans.LanguageInfo, AbBugReporter.BugReportManager, Boolean) at AbBugReporter.BugReportManager.Show(System.Exception) at SSDFresh.App.App_DispatcherUnhandledException(System.Object, System.Windows.Threading.DispatcherUnhandledExceptionEventArgs) at System.Windows.Threading.Dispatcher.CatchException(System.Exception) at MS.Internal.Threading.ExceptionFilterHelper.TryCatchWhen(System.Object, System.Delegate, System.Object, Int32, System.Delegate) at System.Windows.Threading.Dispatcher.WrappedInvoke(System.Delegate, System.Object, Int32, System.Delegate) at System.Windows.Threading.Dispatcher.InvokeImpl(System.Windows.Threading.DispatcherPriority, System.TimeSpan, System.Delegate, System.Object, Int32) at MS.Win32.HwndSubclass.SubclassWndProc(IntPtr, Int32, IntPtr, IntPtr) at MS.Win32.UnsafeNativeMethods.DispatchMessage(System.Windows.Interop.MSG ByRef) at System.Windows.Threading.Dispatcher.PushFrameImpl(System.Windows.Threading.DispatcherFrame) at System.Windows.Application.RunInternal(System.Windows.Window) at System.Windows.Application.Run() at SSDFresh.App.Main() Error 4/2/2012 11:35:39 PM SideBySide 59 None Activation context generation failed for "C:\Windows\Microsoft.NET\Framework64\v4.0.30319\csc.exe".Error in manifest or policy file "C:\Windows\Microsoft.NET\Framework64\v4.0.30319\csc.exe.Config" on line 0. Invalid Xml syntax. Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

    Read the article

  • Alternative Methods of Sharing Folders in Windows?

    - by Blaenk
    Hey guys. I'm running Windows 7 and as of now I simply share folders as one usually does in Windows. I then have a MacBook with Leopard (Now Snow Leopard) which I use to connect to my computer to mount the shares by going to Finder, then CMD + K and typing smb://BlaenkPC (The name of my PC) into the address box. This consequently connects to my computer and mounts all of the shares. The problem is that sometimes, if for example I close my MacBook (Which makes it go to sleep) or sometimes even without doing that, the connection somehow drops. Sometimes I close the MacBook and upon re-opening it, everything still works; it's random. It still shows the computer as being connected, but it just shows 'loading' indefinitely. If I hit 'eject' with the intention of re-connecting to the computer, it disappears from the sidebar (The Computer Icon) in Finder, but I cannot re-connect. Activity Monitor (or ps aux, whichever) both show hung instances of umount; one for each share that was mounted. I cannot kill these processes with kill or killall (Yes, even with sudo, and sending signal -9). This has happened to me before, and here is another person who has experienced this. My question boils down to this: Is there an alternative method of sharing folders in Windows, that my Mac can read/understand, that is possibly more reliable and preferably just as fast? I usually use the mounted shares to watch television episodes off my computer, or movies, etc. (In other words, I open them in VLC and they automatically stream from my computer). As far as I can tell, this is a problem with the Samba protocol. I have heard of NFS, but I am not sure if I would have to re-format my drives, or what. I don't mind running a service or daemon to allow the sharing of the folders, I just want it to be done and hopefully in a better way than typical Windows shares through Samba. Usually when I encounter this problem, which is often (read: every day), I have no other option but to restart the MacBook. As I stated in the first question I linked to, shutting down and restarting don't work; I have to manually force the shutdown by holding the power button. I have not modified my installation of Mac OS X in any hackish way, so I doubt it's something with the Operating System, but worst come to worst, I might end up reformatting and doing a clean install to see if that fixes anything, as I am at a complete loss as to what may be causing the problem, and no one else seems to have any idea or care, despite there being quite a few people suffering from this problem, as my research has shown. Any pieces of information that can help are extremely appreciated. You don't have to answer every question on here, but maybe even some insight as to why it might not be possible to kill those hung umount instances for example, or why I may not be able to reconnect using samba (Is it something regarding the way the protocol works?). One thing to note is that I have another computer in the home network that doesn't seem to have this problem. However, it is also running Windows 7 (Note though that I am not using the homegroup feature, but the typical windows sharing feature). My only deduction is that the problem is being caused by the way the Mac (Or Samba implementation, whichever) is handling things. Perhaps it is a limitation.

    Read the article

  • Troubleshooting Website problems within the local network

    - by HaydnWVN
    Have an external website which opens fine on some PC's, yet seems to time out (or symptoms of timing out, but never actually does) on others. Seems to only affect (some) of our newer HP Pro 3305 MT Workstations. All of which are running Win7 32bit SP1 with all updates. Older PC's (Win7 32bit SP1 & WinXP) are unaffected. Using Google Chrome & Firefox makes no difference. Opening the website in IE9 Compatibility Mode has exactly the same symptoms. All PC's are on the same local network (Workgroup) using the same DNS server & gateway (inhouse) on the same internet connection, on the same subnet. There is no proxy server, no content filtering, no load balancing etc etc. Only group policy in effect (locally) is for Update scheduling. Local firewalls are all the same (Kaspersky WP4) and our external facing firewall has no IP specific settings. I have no control over the external website, traceroute shows the same destination on all PC's. It is a fairly popular website in our industry (Horticulture) and i'm not aware of any other people (even other sites within our sister companies) with the same problem. Update: Used Fiddler2 to monitor the HTTP request, seems its not getting fulfilled for some reason?! Request sent: GET http://www.rhs.org.uk/ HTTP/1.1 Host: www.rhs.org.uk Connection: keep-alive User-Agent: Mozilla/5.0 (Windows NT 6.1) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Encoding: gzip,deflate,sdch Accept-Language: en-GB,en-US;q=0.8,en;q=0.6 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Log from Fiddler 2 of the request: This session is not yet complete. Press F5 to refresh when session is complete for updated statistics. Request Count: 1 Bytes Sent: 567 (headers:567; body:0) Bytes Received: 0 (headers:0; body:0) ACTUAL PERFORMANCE -------------- ClientConnected: 17:02:33.720 ClientBeginRequest: 17:02:39.118 GotRequestHeaders: 17:02:39.118 ClientDoneRequest: 17:02:39.118 Determine Gateway: 0ms DNS Lookup: 0ms TCP/IP Connect: 46ms HTTPS Handshake: 0ms ServerConnected: 17:02:39.165 FiddlerBeginRequest: 17:02:39.165 ServerGotRequest: 17:02:39.165 ServerBeginResponse: 00:00:00.000 GotResponseHeaders: 00:00:00.000 ServerDoneResponse: 00:00:00.000 ClientBeginResponse: 00:00:00.000 ClientDoneResponse: 00:00:00.000 RESPONSE BYTES (by Content-Type) -------------- ~headers~: 0 Log of a successful request from a working PC (done this morning, excuse the timestamps being different from above): Request Count: 1 Bytes Sent: 493 (headers:493; body:0) Bytes Received: 20,413 (headers:525; body:19,888) ACTUAL PERFORMANCE -------------- ClientConnected: 08:22:47.766 ClientBeginRequest: 08:22:47.766 GotRequestHeaders: 08:22:47.766 ClientDoneRequest: 08:22:47.766 Determine Gateway: 0ms DNS Lookup: 26ms TCP/IP Connect: 30ms HTTPS Handshake: 0ms ServerConnected: 08:22:47.828 FiddlerBeginRequest: 08:22:47.828 ServerGotRequest: 08:22:47.828 ServerBeginResponse: 08:22:48.905 GotResponseHeaders: 08:22:48.905 ServerDoneResponse: 08:22:48.905 ClientBeginResponse: 08:22:48.905 ClientDoneResponse: 08:22:48.905 Overall Elapsed: 00:00:01.1388020 RESPONSE BYTES (by Content-Type) -------------- text/html: 19,888 ~headers~: 525 So my question has evolved into: What is the difference between the 2 requests and how do I determine why 1 PC is not getting a reply to it's GET request?

    Read the article

  • i cant ping to my DMZ zone from the local inside PC

    - by Big Denzel
    HI everybody. Can anyone please help me on the following issue. I got a Cisco Asa 5520 configured at my network. I cant ping to my DMZ interface from a local inside network PC. so the only way a ping the DMZ is right from the Cisco ASA firewall, there i can pint to all 3 interfaces, Inside, Outside and DMZ,,,, But no PC from the Inside Network can access the DMZ. Can please any one help? I thank you all in advance Bellow is my Cisco ASA 5520 Firewall show run; ASA-FW# sh run : Saved : ASA Version 7.0(8) ! hostname ASA-FW enable password encrypted passwd encrypted names dns-guard ! interface GigabitEthernet0/0 description "Link-To-GW-Router" nameif outside security-level 0 ip address 41.223.156.109 255.255.255.248 ! interface GigabitEthernet0/1 description "Link-To-Local-LAN" nameif inside security-level 100 ip address 10.1.4.1 255.255.252.0 ! interface GigabitEthernet0/2 description "Link-To-DMZ" nameif dmz security-level 50 ip address 172.16.16.1 255.255.255.0 ! interface GigabitEthernet0/3 shutdown no nameif no security-level no ip address ! interface Management0/0 description "Local-Management-Interface" no nameif no security-level ip address 192.168.192.1 255.255.255.0 ! ftp mode passive access-list OUT-TO-DMZ extended permit tcp any host 41.223.156.107 eq smtp access-list OUT-TO-DMZ extended permit tcp any host 41.223.156.106 eq www access-list OUT-TO-DMZ extended permit icmp any any log access-list OUT-TO-DMZ extended deny ip any any access-list inside extended permit tcp any any eq pop3 access-list inside extended permit tcp any any eq smtp access-list inside extended permit tcp any any eq ssh access-list inside extended permit tcp any any eq telnet access-list inside extended permit tcp any any eq https access-list inside extended permit udp any any eq domain access-list inside extended permit tcp any any eq domain access-list inside extended permit tcp any any eq www access-list inside extended permit ip any any access-list inside extended permit icmp any any access-list dmz extended permit ip any any access-list dmz extended permit icmp any any access-list cap extended permit ip 10.1.4.0 255.255.252.0 172.16.16.0 255.255.25 5.0 access-list cap extended permit ip 172.16.16.0 255.255.255.0 10.1.4.0 255.255.25 2.0 no pager logging enable logging buffer-size 5000 logging monitor warnings logging trap warnings mtu outside 1500 mtu inside 1500 mtu dmz 1500 no failover asdm image disk0:/asdm-508.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (dmz,outside) tcp 41.223.156.106 www 172.16.16.80 www netmask 255.255.255 .255 static (dmz,outside) tcp 41.223.156.107 smtp 172.16.16.25 smtp netmask 255.255.2 55.255 static (inside,dmz) 10.1.0.0 10.1.16.0 netmask 255.255.252.0 access-group OUT-TO-DMZ in interface outside access-group inside in interface inside access-group dmz in interface dmz route outside 0.0.0.0 0.0.0.0 41.223.156.108 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute http server enable http 10.1.4.0 255.255.252.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh timeout 5 console timeout 0 management-access inside ! ! match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect dns maximum-length 512 inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! service-policy global_policy global Cryptochecksum: : end ASA-FW# Please Help. Big Denzel

    Read the article

  • Choice of an OS for a home ZFS NAS

    - by OlafM
    I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post.

    Read the article

  • Supermicro IPMI on MBD-X8DAH+-F-O motherboard. Keyboard and mouse do not work after booting Windows Server 2008 R2

    - by LDelgado
    Hell Everyone, I built a server with the mentioned motherboard. I installed Windows Server 2008 R2 Enterprise on this server. IPMI is integrated on the motherboard with its own dedicated NIC. I've got that NIC configured with its own IP address. I can remote into it using IPMI, and I can remotely control the server settings before booting the OS ( BIOS, RAID configuration, etc). When the OS boots, I lose the mouse and keyboard. I cannot use the keyboard or mouse when installing the OS either. So the Keyboard and Mouse only work when no OS is loaded. Once the OS loads I lose it - that is my problem. I've been doing some research and trying a few things, but I have not been successful in fixing this issue. I may be wrong, but based on the things I've found online, it seems that the problem could be caused by the way the OS handles USB. The server is headless. There is no keyboard, mouse, or monitor plugged into it. When I boot up the OS and remote into it, I cannot see a mouse or keyboard listed in the Device Manager. Based on what I've read, it seems that the OS should detect a mouse and a keyboard when connecting remotely via IPMI. The following are the solutions I've tried. Nothing has worked so far: I've updated the firmware of the IPMI component to the latest firmware - 1.33. I made sure that the mouse mode was set to Absolute (Windows OS). I've loaded the factory defaults several times. I've enabled Port64h/60h Emulation under the USB settings in the BIOS. I've disabled USB legacy support in the BIOS. I made sure the firewall wasn't blocking IPMI (disabled the firewall). And that's about it. I've found threads in some forums from people having the same issue as me, but they were not running the same OS. They were either running Linux or FreeBSD. Most of them fixed their problem by selecting the right mouse mode (Linux in their case). There was one other that solved the problem by disabling USB Mass Storage mode. He stated "When I set it to disable USB Mass Storage when no image is loaded, the ukbd came alive, and I'm typing this on the IPMI Console. " source: http://freebsd.1045724.n5.nabble.com/IPMI-Console-No-luck-once-OS-is-booted-td3967868.html I suspect the solution described in the previous paragraph is somehow related to my problem. I've found several threads on the internet with issues describing the same problem, but none of them were with Windows Server 2008 R2. Again, I may be wrong, but it seems like that could be the issue. I just don't know how I go about applying a solution in Windows Server 2008 R2. In any case, I could use your expertise. Maybe I am missing something, or maybe I'm on the right track. Your help is much appreciated. Thank you in advance,

    Read the article

  • How to diagnose and solve an erratic "HDCP Support Required"?

    - by Jom Orgstrom
    I am playing a digital tv broadcast on Windows Media Center for Windows 7. I built this system so it works with HDCP, and in fact I have been able to watch tv and bluray before with this same computer. However, I suddenly started getting an "HDCP Support Required" error from WMC. The entire message is as follows: HDCP Support Required High-bandwidth Digital Content Protection (HDCP) may not be supported by the current video card. Use an HDCP-compliant display, video card, and video driver. Or, connect using an analog connection such as component or VGA. Relevant specs are: CPU: Ivy Bridge Core i7-3770 Motherboard: Asus P8H77-I Memory: 16GB DDR3-1600 Graphics: Radeon HD 7850 (Driver by AMD, version 8.982.0.0 built on 2012/07/27) Display: Acer P243w connected by HDMI Sound: Roland Quad-Capture (It complains even when I use the bundled VIA HD Audio) TV Tuner: I-O Data GV-MC7/HZ3 OS: Windows 7 Professional SP1, Windows Update enabled. All patched and up to date. As you can see, there is nothing weird or old about my setup. I am also not doing anything strange, not doing any overclocking, weird system changes and so on. One thing that does happen from time to time, is that the display goes black for a few seconds (sometimes when watching media contents, sometimes when just using photoshop or Visual Studio). This happened with my previous setup as well, so I'd be inclined to think it is a display or cable issue (apart from the BD drive, these are the only things I kept from my previous setup to this one). But being a digital transfer, as far as I know, these things either work or not. Never erratically or with decreased quality. The thing is that sometimes I can watch the TV, sometimes not. This happens with recorded programs as well, so it's not a per-program thing. Sometimes rebooting helps, sometimes it doesn't. Sometimes unplugging and plugging back the HDMI connector helps, sometimes it doesn't. Sometimes doing so doesn't even turn the screen back on, so I have to reboot. Unfortunately, WMC's error message is quite unhelpful. I'd like to know exactly where the problem is, so I can solve it. I don't want to buy a brand new display just to then find out it was a registry setting that was misconfigured. I've tried looking at the system event viewer, but these errors don't show up at all in there. Other people who have this problem seem to have a setup that is not HDCP compliant, so I turn to you guys here. Anybody knows how to diagnose this problem? Edit: So I got the Cyberlink Blu-ray disc advisor. I ran it and told me everything was okay, except for the Video Connection Type, which showed as "Digital (without HDCP)". I then proceeded to unplug the power cable from the monitor, plugged it in again, ran the tool again, and now it's "Digital (with HDCP)". Needless to say, I can watch my TV and recorded programs on WMP again. I'm guessing that at some point, something may be slightly wrong with the HDCP setup, and Windows decides to reset the entire content protection path (which leads to the screen blanking out). Usually the reset succeeds, but sometimes it doesn't, so Windows defaults to turning HDCP off. There's no way to turn it back on, except by doing a hard reset of the display. I really want to know what the exact error was, so I can fix it. Is it the cable? is it the display? is it the video card? the driver? Also, is there any other way to try and turn HDCP on again without having to hard reset the display? Oh, questions, questions...

    Read the article

  • What would cause Memcached to Hang for 2+ seconds?

    - by Brad Dwyer
    I'm going nuts trying to scale memcached. From their site: Memcached operations are almost all O(1). Connecting to it and issuing a get or stat command should never lag. If connecting lags, you may be hitting the max connections limit. See ServerMaint for details on stats to monitor. If issuing commands lags, you can have a number of tuning problems. Most common are hardware problems, not enough RAM (swapping), network problems (bandwidth, dropped packets, half-duplex connections). On rare occasion OS bugs or memcached bugs can contribute. Well.. it is most certainly not performing like an O(1) operation for me. Under low to normal load on our site memcached response times for get and set ops are about 0.001 seconds. Not bad. But if we triple the load we get outliers that take 100x (or in rare cases 1000x!) that long. I even had one instance where it took 2.2442 seconds for memcached to store a value. Obviously this is killing our site. Here's the output of Memcached-getStats during one of the slow periods: [pid] => 18079 [uptime] => 8903 [threads] => 4 [time] => 1332795759 [pointer_size] => 32 [rusage_user_seconds] => 26 [rusage_user_microseconds] => 503872 [rusage_system_seconds] => 125 [rusage_system_microseconds] => 477008 [curr_items] => 42099 [total_items] => 422500 [limit_maxbytes] => 943718400 [curr_connections] => 84 [total_connections] => 4946 [connection_structures] => 178 [bytes] => 7259957 [cmd_get] => 1679091 [cmd_set] => 351809 [get_hits] => 1662048 [get_misses] => 17043 [evictions] => 0 [bytes_read] => 109388476 [bytes_written] => 3187646458 [version] => 1.4.13 So things that I have ruled out so far are: Hitting the max connections limit (curr_connections of 84 is well below the default of max of 1024) Swapping - the machine has 900M out of 1024M of memory dedicated to memcached on a dedicated machine. It only appears to be using about 7MB of data as per the bytes stat. How would I diagnose the other hardware problems? prstat doesn't really show a whole lot going on in terms of CPU or memory usage. Not sure how to figure out the network problems but as this is a dedicated server on the same private network as the web box I don't think it's a connectivity issue (ping is less than a millisecond between the boxes). Is there something else I'm missing here? It's driving me nuts. Edit: Also forgot to mention that I've tried both persistent and non-persistent connections with minimal-to-no impact.

    Read the article

  • how to troubleshoot using rsyslog to output to a mysql database

    - by ChrisNZ
    Using FreeBSD 8.0 32 bit. I have installed rsyslogd 5.5.5 with ommysql. (installed ports /usr/ports/sysutils/rsyslog55 and /usr/ports/sysutils/rsyslog55-mysql) My rsyslog.conf file looks like: $ModLoad imudp $ModLoad imtcp $ModLoad ommysql $ModLoad immark.so $ModLoad imuxsock.so $ModLoad imklog.so $OptimizeForUniprocessor on $AllowedSender UDP, 10.0.0.0/8 $UDPServerAddress 0.0.0.0 $UDPServerRun 514 $UDPServerTimeRequery 2 # +SG560 *.* :ommysql:127.0.0.1,Syslog,sysloguser,mypassword My command line flags for rsyslogd are: -c5 -4 Checking the code with -c5 -N1 returns no errors. I have confirmed that rsyslogd is working by changing the last line to say: *.* /var/log/snapgear.log which results in messages appearing in the snapgear.log file. So it is probably something to do with my MySQL setup If I do: mysql -u sysloguser -p Syslog Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 56 Server version: 5.0.86 FreeBSD port: mysql-server-5.0.86 mysql> select * from SystemEvents; Empty set (0.00 sec) mysql> :-( I have confirmed that sysloguser has full privileges for the Syslog database. If I run rsyslogd on the console in debug mode: /usr/local/sbin/rsyslogd -f /usr/local/etc/rsyslog.conf -c5 -n -d I can see this sequence of events each time a message is received: 9244.376687256:28359280: main Q: entry added, size now log 1, phys 1 entries 9244.376705694:28359280: main Q: EnqueueMsg advised worker start 9244.376726647:28359280: Listening on UDP syslogd socket 4 (IPv4/port 514). 9244.376728602:28359280: --------imUDP calling select, active file descriptors (max 4): 4 9244.376890075:283593c0: wti 0x28306e80: worker awoke from idle processing 9244.376892031:283593c0: we deleted 0 objects and enqueued 0 objects 9244.376893986:283593c0: delete batch from store, new sizes: log 1, phys 1 9244.376895942:283593c0: msgConsumer processes msg 0/1 9244.376897898:283593c0: msg parser: flags 70, from '~NOTRESOLVED~', msg 'Jun 29 17:32:24 SG560 kernel: (20000629T1732244' 9244.376900132:283593c0: parse using parser list 0x283080e8 (the default list). 9244.376902088:283593c0: dropped LF at very end of message (DropTrailingLF is set) 9244.376904044:283593c0: Parser 'rsyslog.rfc5424' returned -2160 9244.376905999:283593c0: Message will now be parsed by the legacy syslog parser (one size fits all... ;)). 9244.376907955:283593c0: Parser 'rsyslog.rfc3164' returned 0 9244.376909910:283593c0: testing filter, f_pmask 255 9244.376911866:283593c0: Called action, logging to ommysql 9244.376918012:283593c0: actionTryResume: action state: susp, next retry (if applicable): 1277869250 [now 1277869244] 9244.376919967:283593c0: action call returned -2123 9244.376921923:283593c0: tryDoAction: unexpected error code -2123, finalizing 9244.376926113:283593c0: actionTryResume: action state: susp, next retry (if applicable): 1277869250 [now 1277869244] 9244.376928069:283593c0: ruleset: get iRet 0 from rule.ProcessMsg() 9244.376930024:283593c0: ruleset.ProcessMsg() returns 0 9244.376931980:283593c0: regular consumer finished, iret=0, szlog 0 sz phys 1 9244.376933936:283593c0: XXX: enqueueing data element 0 of 1 9244.376935891:283593c0: we deleted 1 objects and enqueued 0 objects 9244.376938126:283593c0: delete batch from store, new sizes: log 0, phys 0 9244.376940082:283593c0: regular consumer finished, iret=4, szlog 0 sz phys 0 9244.376942037:283593c0: main Q:Reg/w0: worker IDLE, waiting for work. .... I can see the Action Call to ommysql returns unexpected error code -2123 Now I am stuck! Any ideas on what to look for next? Perhaps I there are extra ports I need to install? I will be very grateful for any assistance here!

    Read the article

  • After each command tmux prints: ps1_update: command not found

    - by B.I.
    On Linux Ubuntu 11.04, after each command (cd, ls, vim...) successful or not, tmux prints out as a last line ps1_update: command not found. Is there any config option I am missing? Thank you very much! tmux.conf # http://lukaszwrobel.pl/blog/tmux-tutorial-split-terminal-windows-easily # just remember that after every modification, tmux must be refreshed # to take new settings into account. # This can be achieved either by restarting it or by typing in: # tmux source-file .tmux.conf # Here is a list of a few basic tmux commands: # Ctrl+b " - split pane horizontally. # Ctrl+b % - split pane vertically. # Ctrl+b arrow key - switch pane. # Hold Ctrl+b, don't release it and hold one of the arrow keys - resize pane. # !Ctrl+b c - (c)reate a new window. # !Ctrl+b n - move to the (n)ext window. # Ctrl+b p - move to the (p)revious window. # Shift+LMB - select text. # ALT+Arrows to move among panes. # rebind default prefix to C-a unbind C-b set -g prefix C-a # use ALT+Arrows to move around panes bind -n M-Left select-pane -L bind -n M-Right select-pane -R bind -n M-Up select-pane -U bind -n M-Down select-pane -D # activity monitoring setw -g monitor-activity on set -g visual-activity on # highlight current pane set-window-option -g window-status-current-bg yellow # enable pane switching with mouse set-option -g mouse-select-pane on # read bashrc source ~/.bashrc # Sane scrolling set -g terminal-overrides 'xterm*:smcup@:rmcup@' commandline print out ($(cat)user@tiki:~/.vim$ ls autoload bash_profile bashrc bundle README.md tmux.conf vimrc xmonad xmonad-ubuntu-conf xsessionrc ps1_update: command not found ($(cat)user@tiki:~/.vim$ ll total 56 drwxrwxr-x 2 user user 4096 Mar 17 10:20 autoload/ -rw-rw-r-- 1 user user 170 Mar 17 10:20 bash_profile -rw-rw-r-- 1 user user 4004 Apr 2 11:37 bashrc drwxrwxr-x 20 user user 4096 Aug 20 10:55 bundle/ -rw-rw-r-- 1 user user 11170 Aug 20 11:24 README.md -rw-rw-r-- 1 user user 1243 Mar 17 10:20 tmux.conf ps1_update: command not found ($(cat)user@tiki:~/.vim$ And the following is plain terminal output, without tmux running user@tiki:~$ ls backup_list.md Documents Dropbox examples.desktop hakers_and_painters.md~ hyundai Music projects ror Ubuntu One Videos windows.sh Desktop Downloads elif.txt hakers_and_painters.md help.txt maqola.txt Pictures Public tmp update_background.sh VirtualBox VMs user@tiki:~$ ll total 116 -rw-rw-r-- 1 user user 380 Aug 9 17:34 backup_list.md drwxr-xr-x 6 user user 4096 Jul 15 09:26 Desktop/ drwxr-xr-x 2 user user 4096 Jul 7 11:26 Documents/ drwxr-xr-x 11 user user 20480 Aug 20 13:53 Downloads/ -rwx------ 1 user user 729 May 7 14:45 update_background.sh* drwxr-xr-x 2 user user 4096 Dec 10 2013 Videos/ drwxrwxr-x 4 user user 4096 Sep 10 2013 VirtualBox VMs/ -rwxrwxr-x 1 user user 36 Jan 11 2014 windows.sh* user@tiki:~$ cd Desktop/ user@tiki:~/Desktop$ ll total 36 -rw-rw-r-- 1 user user 3388 Jul 14 17:10 daily--report.md -rw-rw-r-- 1 user user 71 Jan 28 2014 fernandez readme.md -rw-rw-r-- 1 user user 23 Jan 28 2014 fernandez readme.md~ drwx------ 4 user user 4096 Mar 23 14:02 my_docs/ drwx------ 2 user user 4096 Feb 3 2014 Origami/ drwx------ 7 user user 4096 Feb 1 2013 Plants_vs._Zombies_v1.2.0.1065/ -rwxr-xr-x 1 user user 301 Apr 15 11:28 Sky Fight.desktop* drwx------ 2 user user 4096 Feb 11 2014 webdesign/ -rwxrwxr-x 1 user user 26 Jan 11 2014 windows.sh~* user@tiki:~/Desktop$

    Read the article

  • Pushing DNSSEC updates with offline keys

    - by eggyal
    In a non-professional capacity, I look after the DNS of some 18 domains: mostly personal/vanity domains for immediate family. I outsource the whole shebang to an inexpensive managed hosting provider with a web interface through which I manage the zones; since the provider also offers DNSSEC, I have successfully deployed that too. These domains are so unimportant that an attack targetted against them seems much less likely than a general compromise of my provider's systems, at which point the records of all their customers might be changed to misdirect traffic (perhaps with extremely long TTLs). DNSSEC could protect against such an attack, but only if the zone's private keys are not held by the hosting provider. So, I wonder: how can one keep DNSSEC private keys offline yet still transfer signed zones to an outsourced DNS host? The most obvious answer (to me, at least) is to run one's own shadow/hidden master (from which the provider can slave) and then copy offline-signed zonefiles to the master as required. The problem is that the only machine I (want to*) control is my personal laptop, which usually connects from a typical home ADSL (behind NAT over a dynamically-assigned IP address). Having them slave from that (e.g. with a very long Expiry time on the zone for periods when my laptop is offline/unavailable) would not only require a Dynamic DNS record from which they can slave (if indeed they can slave from a named host rather than a static IP address), but would also involve me running a DNS server on my laptop and opening both it and my home network up to the incoming zone transfer requests: not ideal. I would prefer a much more push-oriented design, whereby my laptop initiates transfer of offline-signed zonefiles/updates to the provider's servers. I looked into whether nsupdate could fit the bill: documentation is a little sketchy, but my testing (with BIND 9.7) suggests it can indeed update DNSSEC zones, but only where the server holds the keys to perform the zone signing; I have not found a way to have it take an update including the relevant RRSIG/NSEC/etc. records and have the server accept them. Is this a supported use-case? If not, I suspect the only solutions which could fit the bill will involve non-DNS-based transfer of the zone updates and would welcome recommendations that are supported by (hopefully inexpensive) hosting providers: SFTP/SCP? rsync? RDBMS replication? Proprietary API? Finally, what would be the practical implications of such a setup? Key rotation is jumping out at me as being an obvious difficulty, especially if my laptop is offline for extended periods. But the zones are extremely stable, so perhaps I could get away with long-lived ZSKs**...? * Whilst I could run a shadow/hidden master on e.g. an outsourced VPS, I dislike the overhead of having to secure / manage / monitor / maintain yet another system; not to mention the additional financial costs of so doing. ** Okay, this would enable a concerted attacker to replay outdated records—but the risk and impact of such are both tolerable in the case of these domains.

    Read the article

  • Choice of an OS for a home ZFS NAS

    - by OlafM
    I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post. UPDATES Given the first answers, I will strongly suggest the person paying the hardware to insert a second HD. Better 2x2TB than 1x3TB (3 TB is oversized anyway). I was trying to keep the initial costs down to spread them over a longer period, but better having something good from the beginning.

    Read the article

  • Hosed Windows 7 permissons

    - by Anthony
    Here is the most interesting thing I've noticed since the problems started: If I go into a control panel/system module (in this case the Resource Monitor) that has a "Check Online" type option, Firefox (my default browser) opens right up without a problem. But if I just start Firefox from any shortcuts (start menu, desktop, etc), the Firefox process starts up (and the start menu icon starts glowing) only to end without notice a few seconds later. Possibly related: If I start up in Safe-Mode (w/o Networking, but haven't tried with yet), I can start up FF or Chrome just fine, but if I attempt to open Chrome normally, I get a permissions error. Opera and Safari seem to be okay (mostly). Safari crashes when I try to download any files. All of the above leads me to believe that some (but clearly not all) core files have messed up permissions. Or rather, that I no longer have permission. System still does, based on Firefox opening without fail when the system initiates it. I've run MS Forefront once in normal mode, Malwarebytes twice in normal mode and once in safe-mode. One trojan found and deleted, but the problem persists. Two other things worth mentioning: I accidentally duplicated my library... I thought I'd try to add the "Internet" folder to my start menu, next to music and downloads. The first advanced thing I tried was "create new library". I clearly misunderstood what this means. I thought it was a way to add virtual folders to the library (which I thought, in turn, would allow me to choose it as a link on the start menu), but instead it recreated my already existing user folder, AppData and all. I didn't notice this until today. Then I tried setting permissions for my User folder to full control, recursively... Confused but not giving up,I thought I could maybe create a shortcut to the NetHood folder manually, but instead got hit with an access denied error. So I tried to change the permission levels for all sub-folders to my user folder so that I had full control. I got several access denied errors along the way. At this point I gave up, went out, ended up caught in the rain and stuck on a friend's couch and showing up late for work the next day. Thanks for nothing, Microsoft. When I finally got home today (20 hours later), I noticed that Firefox was acting really strange. I tried opening Chrome to see if the problem was client side or server side, and instead got the above-mentioned "you don't have permission to open this program" alert. And I think that's the whole story. Oh, I also did a system restore, but not chose a point from this morning (an auto update), and it worked but the problem wasn't fixed. And then all the earlier restore points were gone. So the questions are: a) is there a way to set the admin and user privs back to "default"? b) would this, in anyone's expert opinion, fix the problems I'm having? c) how come being logged in as an admin isn't the same as being logged in with admin privs? It seems that half the time I have to do run as admin for fairy standard things because i'm being treated as me-theuser and not me-theadmin. Thanks for reading.

    Read the article

  • Problem with waitable timers in Windows (timeSetEvent and CreateTimerQueueTimer)

    - by MusiGenesis
    I need high-resolution (more accurate than 1 millisecond) timing in my application. The waitable timers in Windows are (or can be made) accurate to the millisecond, but if I need a precise periodicity of, say, 35.7142857141 milliseconds, even a waitable timer with a 36 ms period will drift out of sync quickly. My "solution" to this problem (in ironic quotes because it's not working quite right) is to use a series of one-shot timers where I use the expiration of each timer to call the next timer. Normally a process like this would be subject to cumulative error over time, but in each timer callback I check the current time (with System.Diagnostics.Stopwatch) and use this to calculate what the period of the next timer needs to be (so if a timer happens to expire a little late, the next timer will automagically have a shorter period to compensate). This works as expected, except that after maybe 10-15 seconds the timer system seems to get bogged down, and a few timer callbacks here and there arrive anywhere from 25 to 100 milliseconds late. After a couple of seconds the problem goes away and everything runs smoothly again for 10-15 seconds, and then the stuttering again. Since I'm using Stopwatch to set each timer period, I'm also using it to monitor the arrival times of each timer callback. During the smooth-running periods, most (maybe 95%) of the intervals are either 35 or 36 milliseconds, and no intervals are ever more than 5 milliseconds away from the expected 35.7142857143. During the "glitchy" stretches, the distribution of intervals is very nearly identical, except that a very small number are unusually large (a couple more than 60 ms and one or two longer than 100 ms during maybe a 3-second stretch). This stuttering is very noticeable, and it's what I'm trying to fix, if possible. For the high-resolution timer, I was using the extremely antique timeSetEvent() multimedia timer from winmm.dll. In pursuit of this problem, I switched to using CreateTimerQueueTimer (along with timeBeginPeriod to set the high-resolution), but I'm seeing the same problem with both timer mechanisms. I've tried experimenting with the various flags for CreateTimerQueueTimer which determine which thread the timer runs on, but the stuttering appears no matter what. Is this just a fundamental problem with using timers in this way (i.e. using each one-shot timer to call the next)? If so, do I have any alternatives? One thing I was considering was to determine how many consecutive 1-millisecond-accuracy ticks would keep my within some arbitrary precision limit before I need to reset the timer. So, for example, if I wanted a 35.71428 period, I could let a 36 ms timer elapse 15 times before it was off by 5 milliseconds, then kill it and start a new one.

    Read the article

  • Unauthorized Sharepoint WSDL from Coldfusion 8

    - by antony.trupe
    How do I solve the error: Unable to read WSDL from URL: https://workflowtest.site.edu/_vti_bin/Lists.asmx?WSDL. Error: 401 Unauthorized. I can successfully view the WSDL from the browser using the same user account. I'm not sure which authentication is being used (Basic or Integrated). How would I find that out? The code making the call is: <cfinvoke username="username" password="password" webservice="https://workflowtest.liberty.edu/_vti_bin/Lists.asmx?WSDL" method="GetList" listName="{CB02EB71-392E-4906-B512-8EC002F72436}" > The impression I get is that coldfusion doesn't like being made to authenticate to get the WSDL. Full stack trace: coldfusion.xml.rpc.XmlRpcServiceImpl$CantFindWSDLException: Unable to read WSDL from URL: https://workflowtest.liberty.edu/_vti_bin/Lists.asmx?WSDL. at coldfusion.xml.rpc.XmlRpcServiceImpl.retrieveWSDL(XmlRpcServiceImpl.java:709) at coldfusion.xml.rpc.XmlRpcServiceImpl.access$000(XmlRpcServiceImpl.java:53) at coldfusion.xml.rpc.XmlRpcServiceImpl$1.run(XmlRpcServiceImpl.java:239) at java.security.AccessController.doPrivileged(Native Method) at coldfusion.xml.rpc.XmlRpcServiceImpl.registerWebService(XmlRpcServiceImpl.java:232) at coldfusion.xml.rpc.XmlRpcServiceImpl.getWebService(XmlRpcServiceImpl.java:496) at coldfusion.xml.rpc.XmlRpcServiceImpl.getWebServiceProxy(XmlRpcServiceImpl.java:450) at coldfusion.tagext.lang.InvokeTag.doEndTag(InvokeTag.java:413) at coldfusion.runtime.CfJspPage._emptyTcfTag(CfJspPage.java:2662) at cftonytest2ecfm1787185330.runPage(/var/www/webroot/tonytest.cfm:16) at coldfusion.runtime.CfJspPage.invoke(CfJspPage.java:196) at coldfusion.tagext.lang.IncludeTag.doStartTag(IncludeTag.java:370) at coldfusion.filter.CfincludeFilter.invoke(CfincludeFilter.java:65) at coldfusion.filter.ApplicationFilter.invoke(ApplicationFilter.java:279) at coldfusion.filter.RequestMonitorFilter.invoke(RequestMonitorFilter.java:48) at coldfusion.filter.MonitoringFilter.invoke(MonitoringFilter.java:40) at coldfusion.filter.PathFilter.invoke(PathFilter.java:86) at coldfusion.filter.ExceptionFilter.invoke(ExceptionFilter.java:70) at coldfusion.filter.BrowserDebugFilter.invoke(BrowserDebugFilter.java:74) at coldfusion.filter.ClientScopePersistenceFilter.invoke(ClientScopePersistenceFilter.java:28) at coldfusion.filter.BrowserFilter.invoke(BrowserFilter.java:38) at coldfusion.filter.NoCacheFilter.invoke(NoCacheFilter.java:46) at coldfusion.filter.GlobalsFilter.invoke(GlobalsFilter.java:38) at coldfusion.filter.DatasourceFilter.invoke(DatasourceFilter.java:22) at coldfusion.CfmServlet.service(CfmServlet.java:175) at coldfusion.bootstrap.BootstrapServlet.service(BootstrapServlet.java:89) at jrun.servlet.FilterChain.doFilter(FilterChain.java:86) at coldfusion.monitor.event.MonitoringServletFilter.doFilter(MonitoringServletFilter.java:42) at coldfusion.bootstrap.BootstrapFilter.doFilter(BootstrapFilter.java:46) at jrun.servlet.FilterChain.doFilter(FilterChain.java:94) at jrun.servlet.FilterChain.service(FilterChain.java:101) at jrun.servlet.ServletInvoker.invoke(ServletInvoker.java:106) at jrun.servlet.JRunInvokerChain.invokeNext(JRunInvokerChain.java:42) at jrun.servlet.JRunRequestDispatcher.invoke(JRunRequestDispatcher.java:286) at jrun.servlet.ServletEngineService.dispatch(ServletEngineService.java:543) at jrun.servlet.jrpp.JRunProxyService.invokeRunnable(JRunProxyService.java:203) at jrunx.scheduler.ThreadPool$DownstreamMetrics.invokeRunnable(ThreadPool.java:320) at jrunx.scheduler.ThreadPool$ThreadThrottle.invokeRunnable(ThreadPool.java:428) at jrunx.scheduler.ThreadPool$UpstreamMetrics.invokeRunnable(ThreadPool.java:266) at jrunx.scheduler.WorkerThread.run(WorkerThread.java:66)

    Read the article

  • WiX unresolved reference error

    - by David
    I'm using Wix version 3.0.5419.0. I have two .wxs files, one which is a fragment, and another which uses the fragment to create the .msi file. Here is the file which uses the fragment (DaisyFarmer.wxs): <?xml version='1.0' encoding='windows-1252'?> <Wix xmlns='http://schemas.microsoft.com/wix/2006/wi' xmlns:iis='http://schemas.microsoft.com/wix/IIsExtension'> <Product Name='Daisy Web Site 1.0' Id='BB7FBBE4-0A25-4cc7-A39C-AC916B665220' UpgradeCode='8A5311DE-A125-418f-B0E1-5A30B9C667BD' Language='1033' Codepage='1252' Version='1.0.0' Manufacturer='the man'> <Package Id='5F341544-4F95-4e01-A2F8-EF74448C0D6D' Keywords='Installer' Description="desc" Manufacturer='the man' InstallerVersion='100' Languages='1033' Compressed='yes' SummaryCodepage='1252' /> <Media Id='1' Cabinet='Sample.cab' EmbedCab='yes' DiskPrompt="CD-ROM #1" /> <Property Id='DiskPrompt' Value="the man" /> <PropertyRef Id="NETFRAMEWORK35"/> <Condition Message='This setup requires the .NET Framework 3.5.'> <![CDATA[Installed OR (NETFRAMEWORK35)]]> </Condition> <Feature Id='DaisyFarmer' Title='DaisyFarmer' Level='1'> <ComponentRef Id='SchedulerComponent' /> </Feature> </Product> </Wix> The fragment I'm referencing is (Scheduler.wxs): <?xml version="1.0" encoding="utf-8"?> <Wix xmlns="http://schemas.microsoft.com/wix/2006/wi"> <Fragment> <DirectoryRef Id="TARGETDIR"> <Directory Id="dir2787390E4B7313EB8005DE08108EFEA4" Name="scheduler"> <Component Id="SchedulerComponent" Guid="{9254F7E1-DE41-4EE5-BC0F-BA668AF051CB}"> <File Id="fil9A013D0BFB837BAC71FED09C59C5501B" KeyPath="yes" Source="SourceDir\DTBookMonitor.exe" /> <File Id="fil4F0D8D05F53E6AFBDB498E7C75C2D98F" KeyPath="no" Source="SourceDir\DTBookMonitor.exe.config" /> <File Id="filF02F4686267D027CB416E044E8C8C2FA" KeyPath="no" Source="SourceDir\monitor.bat" /> <File Id="fil05B8FF38A3C85FE6C4A58CD6FDFCD2FB" KeyPath="no" Source="SourceDir\output.txt" /> <File Id="fil397F04E2527DCFDF7E8AC1DD92E48264" KeyPath="no" Source="SourceDir\pipelineOutput.txt" /> <File Id="fil83DFACFE7F661A9FF89AA17428474929" KeyPath="no" Source="SourceDir\process.bat" /> <File Id="fil2809039236E0072642C52C6A52AD6F2F" KeyPath="no" Source="SourceDir\README.txt" /> </Component> </Directory> </DirectoryRef> </Fragment> </Wix> I then run the following commands: candle -ext WixUtilExtension -ext WiXNetFxExtension DaisyFarmer.wxs Scheduler.wxs light -sice:ICE20 -ext WixUtilExtension -ext WiXNetFxExtension Scheduler.wixobj DaisyFarmer.wixobj -out DaisyFarmer.msi I'm getting an error when I run light.exe which says "DaisyFarmer.wxs(20) : error LGHT0094 : Unresolved reference to symbol 'Component:SchedulerComponent' in section 'Product:{BB7FBBE4-0A25-4CC7-A39C-AC916B665220}'." What am I missing?

    Read the article

  • .Net Intermittent System.Web.Services.Protocols.SoapHeaderException

    - by ScottE
    We have a .net 3.5 web app that consumes third party web services. The proxy was created by adding a web reference to their wsdl. This proxy is not compiled. Our error logging is picking up frequent but intermittent exceptions: An exception of type 'System.Web.Services.Protocols.SoapHeaderException' occurred and was caught If I follow the url to the page that generated the exception, I can't recreate it. Edit: Here is most of the exception - where it bubbled up from Message : Internal Error Type : System.Web.Services.Protocols.SoapHeaderException, System.Web.Services, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a Source : System.Web.Services Help link : Actor : Code : http://schemas.xmlsoap.org/soap/envelope/:Client Detail : Lang : Node : Role : SubCode : Data : System.Collections.ListDictionaryInternal TargetSite : System.Object[] ReadResponse(System.Web.Services.Protocols.SoapClientMessage, System.Net.WebResponse, System.IO.Stream, Boolean) Stack Trace : at System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) at System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) at Vendor.getSearch(getSearchRequest getSearchRequest) in c:\WINDOWS\Microsoft.NET\Framework\v2.0.50727\Temporary ASP.NET Files\root\be43c34e\b09edc7e\App_WebReferences.pww-cf-q.0.cs:line 73 Edit 2: Inner exceptions: I sometimes get the following inner exceptions logged: Message : Unable to read data from the transport connection: An existing connection was forcibly closed by the remote host. Type : System.IO.IOException, mscorlib, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089 Source : System Help link : Data : System.Collections.ListDictionaryInternal TargetSite : Int32 Read(Byte[], Int32, Int32) Stack Trace : at System.Net.Sockets.NetworkStream.Read(Byte[] buffer, Int32 offset, Int32 size) at System.Net.FixedSizeReader.ReadPacket(Byte[] buffer, Int32 offset, Int32 count) at System.Net.Security.SslState.StartReceiveBlob(Byte[] buffer, AsyncProtocolRequest asyncRequest) at System.Net.Security.SslState.CheckCompletionBeforeNextReceive(ProtocolToken message, AsyncProtocolRequest asyncRequest) at System.Net.Security.SslState.StartSendBlob(Byte[] incoming, Int32 count, AsyncProtocolRequest asyncRequest) at System.Net.Security.SslState.ForceAuthentication(Boolean receiveFirst, Byte[] buffer, AsyncProtocolRequest asyncRequest) at System.Net.Security.SslState.ProcessAuthentication(LazyAsyncResult lazyResult) at System.Net.TlsStream.CallProcessAuthentication(Object state) at System.Threading.ExecutionContext.runTryCode(Object userData) at System.Runtime.CompilerServices.RuntimeHelpers.ExecuteCodeWithGuaranteedCleanup(TryCode code, CleanupCode backoutCode, Object userData) at System.Threading.ExecutionContext.RunInternal(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Net.TlsStream.ProcessAuthentication(LazyAsyncResult result) at System.Net.TlsStream.Write(Byte[] buffer, Int32 offset, Int32 size) at System.Net.PooledStream.Write(Byte[] buffer, Int32 offset, Int32 size) at System.Net.ConnectStream.WriteHeaders(Boolean async) And/Or: Message : An existing connection was forcibly closed by the remote host Type : System.Net.Sockets.SocketException, System, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089 Source : System Help link : ErrorCode : 10054 SocketErrorCode : ConnectionReset NativeErrorCode : 10054 Data : System.Collections.ListDictionaryInternal TargetSite : Int32 Receive(Byte[], Int32, Int32, System.Net.Sockets.SocketFlags) Stack Trace : at System.Net.Sockets.Socket.Receive(Byte[] buffer, Int32 offset, Int32 size, SocketFlags socketFlags) at System.Net.Sockets.NetworkStream.Read(Byte[] buffer, Int32 offset, Int32 size) Update We're still working on it. Originally there was a route issue, which was resolved. We're still getting the inner exception with socket errors. We had MS support involved today, and they looked at some traces and network captures. The web service host does round-robin DNS, and they may be responding on a different IP address for the syn syn/ack from one ip, and the next from a different ip. This is not good. This is likely quite specific to our situation, but perhaps it applies to others as well. Microsoft Network Monitor and an application trace got us the information we needed.

    Read the article

  • rspec & rails 3 cannot find model object

    - by Ceilingfish
    I'm trying to put some specs around a new rails 3 project I am working on, and my first test doesn't seem to be able to find a model. I've installed rspec from the command line using: sudo gem install rspec --pre and then I put the following in my Gemfile gem "rspec-rails", ">= 2.0.0.beta.1" But when I run my test I get ./spec/models/world_spec.rb:1: uninitialized constant World (NameError) rake aborted! Command /opt/local/bin/ruby -Ilib -Ispec "./spec/models/world_spec.rb" failed /opt/local/lib/ruby/gems/1.8/gems/rspec-core-2.0.0.beta.4/lib/rspec/core/rake_task.rb:71:in `define' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:1112:in `verbose' /opt/local/lib/ruby/gems/1.8/gems/rspec-core-2.0.0.beta.4/lib/rspec/core/rake_task.rb:57:in `send' /opt/local/lib/ruby/gems/1.8/gems/rspec-core-2.0.0.beta.4/lib/rspec/core/rake_task.rb:57:in `define' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:636:in `call' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:636:in `execute' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:631:in `each' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:631:in `execute' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:597:in `invoke_with_call_chain' /opt/local/lib/ruby/1.8/monitor.rb:242:in `synchronize' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:590:in `invoke_with_call_chain' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:583:in `invoke' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2051:in `invoke_task' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2029:in `top_level' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2029:in `each' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2029:in `top_level' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2068:in `standard_exception_handling' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2023:in `top_level' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2001:in `run' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2068:in `standard_exception_handling' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:1998:in `run' /opt/local/lib/ruby/gems/1.8/gems/rake-0.8.7/bin/rake:31 /opt/local/bin/rake:19:in `load' /opt/local/bin/rake:19 My spec is in spec/models/world_spec.rb, and looks like describe World, "#hello" do it "should be invalid" do World.new.should be_invalid? end end I tried adding a line like require "app/model/world" and require "world" but to no success. Does anyone know what I'm doing wrong?

    Read the article

  • jQuery monitoring form field created by AJAX query

    - by Jon Rhoades
    Preface: I am sure this is incredibly simple, but I have searched this site & the jQuery site and can't figure out the right search term to get an answer - please excuse my ignorance! I am adding additional form fields using jQuery's ajax function and need to then apply additional ajax functions to those fields but can't seem to get jQuery to monitor these on the fly form fields. How can I get jQuery to use these new fields? $(document).ready(function() { $('#formField').hide(); $('.lnk').click(function() { var t = this.id; $('#formField').show(400); $('#form').load('loader.php?val=' + t); }); //This works fine if the field is already present var name = $('#name'); var email = $('#email'); $('#uid').keyup(function () { var t = this; if (this.value != this.lastValue) { if (this.timer) clearTimeout(this.timer); this.timer = setTimeout(function () { $.ajax({ url: 'loader.php', data: 'action=getUser&uid=' + t.value, type: 'get', success: function (j) { va = j.split("|"); displayname = va[1]; mail = va[2]; name.val(displayname); email.val(mail); } }); }, 200); this.lastValue = this.value; } }); }); So if the is present in the basic html page the function works, but if it arrives by the $.load function it doesn't - presumably because $(document).ready has already started. I did try: $(document).ready(function() { $('#formField').hide(); $('.lnk').click(function() { var t = this.id; $('#formField').show(400); $('#form').load('loader.php?val=' + t); prepUid(); }); }); function prepUid(){ var name = $('#name'); var email = $('#email'); $('#uid').keyup(function () { snip........... But it didn't seem to work...

    Read the article

  • MKMapView memory usage grows out of control with setRegion: calls

    - by Kurt
    Hi, I have a single MKMapView instance that I have programmatically added to a UIView. As part of the UI, the user can cycle through a list of addresses and the map view is updated to show the correct map for each address as the user goes through them. I create the map view once, and simply change what it displays with setRegion:animated:. The problem is that each time the map is changed to show a new address, the memory usage of my program increases by 200K-500K (as reported by Memory Monitor in Instruments). According to Object Allocations, it appears that a lot of 1.0K Mallocs are happening each time, and the Extended Detail pane for these 1.0K allocations shows that the Responsible Caller is convert_image_data and the Extended Detail pane shows that this is the result of [MKMapTileView drawLayer:inContext:]. So, seems likely to me that the memory usage is due to MKMapView not freeing memory it uses to redraw the map each time. In fact, when I don't display the map at all (by not even adding it as a subview of my main UIView) but still cycle through the addresses (which changes various UILabels and other displayed info) the memory usage for the app does NOT increase. If I add the map view but never update it with setRegion:, the memory also does NOT increase when changing to a new address. One more bit of info: if I go to a new address (and therefore ask the map to display the new address) the memory jumps as described above. However, if I go back to an address that was already displayed, the memory does not jump when the map redraws with the old address. Also, this happens on iPad (real device) with 3.2 and on iPhone (again, real device) with 3.1.2. Here's how I initialize the MKMapView (I only do this once): CGRect mapFrame; mapFrame.origin.y = 460; // yes, magic numbers. just for testing. mapFrame.origin.x = 0; mapFrame.size.height = 500; mapFrame.size.width = 768; mapView = [[MKMapView alloc] initWithFrame:mapFrame]; mapView.delegate = self; [self.view insertSubview:mapView atIndex:0]; And in response to the user selecting an address, I set the map like so: MKCoordinateRegion region; MKCoordinateSpan span; span.latitudeDelta=kStreetMapSpan; // 0.003 span.longitudeDelta=kStreetMapSpan; // 0.003 region.center = address.coords; // coords is CLLocationCoordinate2D region.span = span; mapView.region.span = span; [mapView setRegion:region animated:NO]; Any thoughts? I've scoured the net but haven't seen mention of this problem, and I've reached the limits of my Instruments knowledge. Thanks for any ideas.

    Read the article

  • Using 32bit COM object from C# or VBS on Vista 64bit and getting error 80004005

    - by alexandroid
    I need some mind reading here, since I am trying to do what I do not completely understand. There is a 32-bit application (electronic trading application called CQG) which provides a COM API for external access. I have sample programs and scripts which access this API from Excel, .NET (C++, VB and C#) and shell VBScript. I have these .NET applications as source code and as compiled executables (32-bit, compiled on Windows XP). Now I have Windows Vista Home 64-bit which makes my head to spin. Excel examples work just fine (in Excel 2003). Compiled .NET sample executables work as well. But when I am trying to run .NET C# sample converted to and compiled by Visual Studio C# Expression, or run the VBScript script, I am getting error 80004005 when trying to create an object. Initially the .NET application also gave me 80040154 but then I figured how to make it produce 32-bit code and not 64-bit, so now the errors in C# and VBScript applications are the same. That's all the progress I got for now. And yes, I tried running 32-bit versions of cscript.exe/WScript from SysWOW64 folder on my VBS, but still the result is the same (80004005). How to solve this problem? I am almost ready to believe it is practically impossible, but the fact that Excel VBA works and .NET executables compiled on Windows XP run just fine just makes me angry. There should be a way to beat this thing (some secret which probably only Windows Vista developers know)! I will appreciate any help! PS: I believe code samples do not make much sense here, but this is the line of VBScript which fails: Set CEL = WScript.CreateObject("CQG.CQGCEL.4.0", "CEL_") And this is C#: CQGCEL CEL = new CQGCEL(); Update: Forgot to say UAC is off, of course. And I am working from account with administrator priviledges. I also tried watching which registry keys are read using Process Monitor but everything looks OK for GUIDs of this object. I could not recognize some other GUIDs so I am not sure whether they were critical or not. Is there a chance that this COM object uses Internet Explorer and gets the wrong one (like Internet Explorer 7 instead of Internet Explorer 6 engine or something)?

    Read the article

  • Unable to rename file with c# ftp methods when current user directory is different from root

    - by Agata
    Hello everyone, Remark: due to spam prevention mechanizm I was forced to replace the beginning of the Uris from ftp:// to ftp. I've got following problem. I have to upload file with C# ftp method and afterwards rename it. Easy, right? :) Ok, let's say my ftp host is like this: ftp.contoso.com and after logging in, current directory is set to: users/name So, what I'm trying to achieve is to log in, upload file to current directory as file.ext.tmp and after upload is successful, rename the file to file.ext The whole difficulty is, as I guess, to properly set the request Uri for FtpWebRequest. MSDN states: The URI may be relative or absolute. If the URI is of the form "ftp://contoso.com/%2fpath" (%2f is an escaped '/'), then the URI is absolute, and the current directory is /path. If, however, the URI is of the form "ftp://contoso.com/path", first the .NET Framework logs into the FTP server (using the user name and password set by the Credentials property), then the current directory is set to UserLoginDirectory/path. Ok, so I upload file with the following URI: ftp.contoso.com/file.ext.tmp Great, the file lands where I wanted it to be: in directory "users/name" Now, I want to rename the file, so I create web request with following Uri: ftp.contoso.com/file.ext.tmp and specify rename to parameter as: file.ext and this gives me 550 error: file not found, no permissions, etc. I traced this in Microsoft Network Monitor and it gave me: Command: RNFR, Rename from CommandParameter: /file.ext.tmp Ftp: Response to Port 53724, '550 File /file.ext.tmp not found' as if it was looking for the file in the root directory - not in the current directory. I renamed the file manually using Total Commander and the only difference was that CommandParameter was without the first slash: CommandParameter: file.ext.tmp I'm able to successfully rename the file by supplying following absolute URI: ftp.contoso.com/%2fusers/%2fname/file.ext.tmp but I don't like this approach, since I would have to know the name of current user's directory. It can probably be done by using WebRequestMethods.Ftp.PrintWorkingDirectory, but it adds extra complexity (calling this method to retrieve directory name, then combining the paths to form proper URI). What I don't understand is why the URI ftp.contoso.com/file.ext.tmp is good for upload and not for rename? Am I missing something here? The project is set to .NET 4.0, coded in Visual Studio 2010.

    Read the article

  • activeX component in axapta

    - by Nico
    hi folks, i'm struggling with an .net activeX i try to use in ms axapta 2009. using this component on my local machine where it was compiled, it's working quite fine. it can be added as activeX element on a form, the methods and events are listed in the axapta-activeX-explorer and i can interact with it without any problems. but trying to distribute the dll to other clients isn't working as intended. the registration of the dll via regasm /codebase /tlb works properly - getting the message, registration was successful. the component is also listed when selecting an activeX-element to add in ax, but neither functions nor properties are listed. and launching the form results in an errormessage - activeX component CLSID ... not found on system, not installed. the classID is indeed the one, defined in .net. strange things happen, having a look on the task-manager. the activeX-component itself is just a wrapper to interact with a com-application. when launching the ax-form with the not working and _not_installed_!! activeX-thing, the taskmanager shows a new process of the com-application, which is instanciated by the activeX :/ things i tried: using different versions of regasm, eg \Windows\Microsoft.NET\Framework\v2.0.50727 ; C:\Windows\Microsoft.NET\Framework64\v2.0.50727 using new GUIDs in .net, prior removing the old ones from the registry compiling, using different versions of the .net framework doing registration via regasm, regasm /codebase, regasm /codebase /tlb, using a visual-studio-setup running registration via command-line as administrator running setup as administrator running even ax as administrator on client-machine moving dll to a different folder followed by new registration ( windows/system32; ax/client/bin ) installing to GAC ( gacutil /i ) different project-options in visual studio ( COM-Visibility; register for COM-Interop; different targetPlatform ) hoped for the fact, that compiling in visual studio with register for COM-Interop option enabled does something more than just the regasm-registration, i used a registry-monitor-microsoft-tool for logging the registry-activity which happend during compilation. using these logs to create all registry-entries on the target-client in addition didn't work either. any hints or help would be so much appreciated! this thing is blocking me for days now :(

    Read the article

  • mysql error using Rails-- Please help

    - by Cypher
    Alright I am sry for the noob question but this has been driving me up a wall-especially because I got it to work yesterday and I can't remember what I did.... I am just trying to use mysql with rails with a mongrel server. I set up the server fine and can run rails applications that don't need mysql but when I create a project using (for example) rails -d mysql blog and then create some simple controller e.g. ruby script/generate Test then put this code in the controller... class TestController < ApplicationController def index render :text => 'WORK' end end then when I start the server up and open up localhost:3000/test I get the following error: = Booting Mongrel = Rails 2.3.5 application starting on http://0.0.0.0:3000 = Call with -d to detach = Ctrl-C to shutdown server /!\ FAILSAFE /!\ Mon May 10 20:15:06 -0500 2010 Status: 500 Internal Server Error Can't connect to MySQL server on 'localhost' (10061) C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/mysql_adapter.rb:589:in 'real_connect' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/mysql_adapter.rb:589:in 'connect' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/mysql_adapter.rb:203:in 'initialize' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/mysql_adapter.rb:75:in 'new' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/mysql_adapter.rb:75:in 'mysql_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/abstract/connection_pool.rb:223:in 'send' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/abstract/connection_pool.rb:223:in 'new_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/abstract/connection_pool.rb:245:in 'checkout_new_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/abstract/connection_pool.rb:188:in 'checkout' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/abstract/connection_pool.rb:184:in 'loop' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/abstract/connection_pool.rb:184:in 'checkout' C:/Ruby/lib/ruby/1.8/monitor.rb:242:in 'synchronize' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/abstract/connection_pool.rb:183:in 'checkout' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/abstract/connection_pool.rb:98:in 'connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/abstract/connection_pool.rb:326:in 'retrieve_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/abstract/connection_specification.rb:123:in 'retrieve_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_adapter s/abstract/connection_specification.rb:115:in 'connection' etc... In the browser i get a 'We're sorry, but something went wrong' Does anyone know what I am doing wrong?

    Read the article

< Previous Page | 218 219 220 221 222 223 224 225 226 227 228 229  | Next Page >