Search Results

Search found 14402 results on 577 pages for 'interface builder'.

Page 226/577 | < Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >

  • iptables : how to allow incoming ftp traffic?

    - by logansama
    Hi, Still fighting my way through the jungle that is called iptables. I have managed to allow FTP access outside of our LAN: both these would work. NOTE: eth0 is the LAN interface and eth1 is the WAN interface. iptables -t filter -A FORWARD -i eth0 -p tcp --dport 20:21 -j ACCEPT or iptables -A FORWARD -i eth0 -o eth1 -p tcp --sport 20:21 --dport 1024:65535 -j ACCEPT But when i connect to a external FTP server i manage to log in and all is fine until it wishes to List the directory content. Then nothing happens as the data is blocked, due to the fact that i do not have a rule set up to allow it! (my last rule on the FORWARD chain is to block all traffic) I have tried a gazillion rules (many of which i did not understand) to try and allow the FTP traffic back through my server. One such rule for example was: iptables -A FORWARD -i eth1 -o eth0 -p tcp --sport 20:21 --dport 1024:65535 -j ACCEPT But i cannot get the List to work. It just times out after a while. Would anyone perhaps know how to build a rule which would allow FTP to List / allow such traffic back? Or have a link to sources i could work through? Thank you,

    Read the article

  • USB-to-Serial showing gibberish at 115200 Baud

    - by Mose
    I've got a serious problem which drives me crazy because I tried everything I could think of. First of all, I made a video: http://youtu.be/boghkuq7L_s but please read the following text for more information, not only view the video! When using a USB-to-Serial interface everything works as long as I don't go beyond 57600 Baud. At higher rates I only get giberish like this: év.­b0JNLYÆÿ¿iëd0U²(kßÞb! ú]/xscB!ï¯!BoXûÿ1ïâÖCÿ6ÌAnè*íÌC)º¿BíÞØ.C.@ÆÃwHJÂs "YE:ñ.èFðÌCÊ÷ÞÄ !x H w6@BtbHJ ̪ Ì6ì H¾a¿bH.">îvy®;f<ßBÌ p­L¨fæH­E ­þ¼MBÞI What makes the problem so strange is, I exchanged every component and the problem still presists. I tried differtent OSes (Ubuntu, WinXP, Win7, OSX 10.7) with 32 and 64 Bit. I tried USB-to-Serial interface from FTDI and Prolific. I tried reading the output from my Raspberry PI and from an Asterisk Appliance. I changed the cables and the wiring. Nothing helped. In the video I made a example with a old Notebook with native COM and put the USB-to-Serial to the same connection as "sniffer" (only Rx and GND connected) to make sure the output and everything is ok as one can see on the native port. The voltage is ok. Settings for both are 115200 Baud, 8 Bit with 1 Stop and no flow control. Native is ok. USB is messed up. I used the newest drivers and double checked all connections. I have no idea what is wrong here. As I couldn't find anyone describing problems like this I question my long experiance in computer science and think I'm doing some completly wrong... Please help :-/

    Read the article

  • Ubuntu IP Configuration - multiple subnets & interfaces

    - by HaydnWVN
    Have a 'new' mailserver running postfix on Ubuntu. We are having some problems configuring the subnets & interfaces. Basically 2 subnets (.253. & .254.) need to be connected through the 3rd subnet (.252.) where the Router is residing. # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.62.254.199 netmask 255.255.0.0 network 10.62.254.0 broadcast 10.62.255.255 #gateway 10.62.252.138 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 10.62.252.138 dns-search ***.com auto eth1 iface eth1 inet static address 10.62.253.199 netmask 255.255.0.0 network 10.62.253.0 broadcast 10.62.255.255 #gateway 10.62.252.138 #dns-nameservers 10.62.254.199 10.62.253.199 10.62.252.199 dns-nameservers 10.62.252.138 dns-search ***.com auto eth2 iface eth2 inet static address 10.62.252.199 netmask 255.255.0.0 network 10.62.252.0 broadcast 10.62.255.255 gateway 10.62.252.138 #dns-nameservers 10.62.254.199 10.62.253.199 10.62.252.199 dns-search ***.com I have an external support company who are looking into this (they built and configured this server), but it's taking far too long... So I'm looking to highlight the mistake!

    Read the article

  • How to write rules for persistent net names?

    - by ndemou
    I know that a process generates persistent network card names based on rules found in /lib/udev/rules.d/75-persistent-net-generator.rules. I also know how to completely disable this process with a simple echo '#' > /etc/udev/rules.d/75-persistent-net-generator.rules but I've read that I "could also write my own rules file to give the interface a name — the persistent rules generator ignores the interface if a name has already been set" (/etc/udev/rules.d/README confirms that this is possible). Do you have any pointers to documentation about how to write such rules? (I mostly care about Debian/Ubuntu and a bit less for CentOS) As a specific example of why I want to write custom rules: I have two identical servers with one onboard LAN and one PCI LAN. In case of HW failure I want to be able to move disks from HW#1 to HW#2 and it's important for eth0 to continue pointing to the onboard card and eth1 to the PCI card (no one wants to mess with cabling in the middle of a HW failure panic). My current workaround works but is a lot of work[1] so I wonder if writing custom rules would allow me to express something simple like this: cards with MAC A or B should be named eth0 cards with MAC C or D should be named eth1 follow default naming scheme for anything else [1] install the OS in HW#1 and keep a copy of /etc/udev/rules.d/70-persistent-net.rules. Move the disks to HW#2 and keep a second copy of the same file. Concatenate the two copies and manually edit the NAME="ethX" part. Replace /etc/udev/rules.d/70-persistent-net.rules with my version. Finally disable auto-creation of a new 70-persistent-net.rules using echo '#' > /etc/udev/rules.d/75-persistent-net-generator.rules

    Read the article

  • Linux as a router for public networks

    - by nixnotwin
    My ISP had given me a /30 network. Later, when I wanted more public ips, I requested for a /29 network. I was told to keep using my earlier /30 network on the interface which is facing ISP, and the newly given /29 network should be used on the other interface which connects to my NAT router and servers. This is what I got from the isp: WAN IP: 179.xxx.4.128/30 CUSTOMER IP : 179.xxx.4.130 ISP GATEWAY IP:179.xxx.4.129 SUBNET : 255.255.255.252 LAN IPS: 179.xxx.139.224/29 GATEWAY IP :179.xxx.139.225 SUBNET : 255.255.255.248 I have a Ubuntu pc which has two interfaces. So I am planning to do the following: eth0 will be given 179.xxx.4.130/30 gateway 179.xxx.4.129 eth1 will be given 179.xxx.139.225/29 And I will have the following in the /etc/sysctl.conf: net.ipv4.ip_forward=1 These will be iptables rules: iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT My clients which have the ips 179.xxx.139.226/29 and 179.xxx.139.227/29 will be made to use 179.xxx.139.225/29 as gateway. Will this configuration work for me? Any comments? If it works, what iptables rules can I use to have a bit of security? P.S. Both networks are non-private and there is no NATing.

    Read the article

  • How to define nodes from a Hiera file in Puppet?

    - by Pigueiras
    I am using puppet and the puppet network device management module and I am trying to build my custom type. In the built-in type for the routers configuration, you can specify a list of nodes and then the configuration inside that node: node "c2950.domain.com" { Interface { duplex => auto, speed => auto } interface { "FastEthernet 0/1": description => "--> to end-user workstation", mode => access, native_vlan => 1000 # [...] More configuration } What I am trying to do, is to move the manifest declaration of the nodes and the configuration of my custom type to a Hiera file like this one: nodes: - node1 - node2 config_device: node1: custom_parameter: "whatever1" node2: custom_parameter: "whatever2" And then in the manifest iterate over the hiera file creating the nodes with the configuration of each node with something like (I am taking as reference this question in serverfault): class my_class { $nodes = hiera_array('nodes') define hash_extract() { $conf_hash = hiera_hash("config_device") $custom_paramter = $conf_hash[$name] ## TRICK lies in $name variable node $name { my_custom_device { $name: custom_parameter => $device_conf['custom_parameter'] } } } hash_extract{$pdu_names: } } } But for this solution I have two problems, I can not define a node inside a define and I can not parameterize a node name. So, is there any way to declare nodes from a Hiera file with their configuration inside?

    Read the article

  • Recommendations for good Unix MTA / groupware solutions? [closed]

    - by Jez
    Possible Duplicate: Exchange server replacement that runs on Linux I'm setting up a Debian server, and one of the things I need on it is an MTA. I don't want to use something like Exim or Postfix because I want something that ties in SMTP, POP3, and IMAP all in one (a la Microsoft Exchange). Most MTAs also seem to be hellishly difficult to configure. Try and read the Exim documentation; you could do a university degree on it (I'm not kidding). When you can get an HTTP server like Cherokee which is easy to configure and has a nice web interface, do MTAs or groupware solutions need to be that hard? I'm aware that some people think "the Unix way" is to have lots of different interacting pieces of software (like maybe an SMTP MTA, POP3 service, webmail service, and overarching manager to tie them all together), but I think this is a situation where that just makes things a lot harder to deal with and one large software suite fits in much more nicely. So, I'm looking for good open source software suites that will run on Debian that: Combine (at least) SMTP, POP3, and IMAP Are easy(ish) to configure Have a nice configuration web interface or GUI Are not defunct projects I don't mind if it's groupware and offers calendaring too, but I would only be using the e-mail functionality for now. Another nice-to-have would be built-in webmail (if we're combining a bunch of functionality, why not?) Note however that I do NOT need Outlook support. I am not really looking for an "Exchange replacement drop-in". The suites I've found so far that seem to match the above criteria (and have appropriate licenses) are Citadel, Kolab, and Zimbra. I'd appreciate anyone who has experience with any of these giving me the pros and cons of them, such as how easy they are to configure and what their performance is like. I'd also appreciate any other suggestions for solutions that fulfil my criteria that I may have missed out.

    Read the article

  • Wireless driver activation issue in Compaq c700 in Ubuntu 9.04

    - by Fazil
    I am using Ubuntu 9.04, I cant access my wireless driver, I activate the madwifi in administrationhardware drivers, but I could'nt activated the wireless too. when I type lspci I get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when I tried in Windows I found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can I do for solving this problem.

    Read the article

  • Todo/task manager for android and desktop linux

    - by RiaD
    I'm looking forward to Task/ToDo Manager. It should work under Android, Linux(or Web). If it's very cool, one of them is OK too, Android is preferable in this situation. Necessary features: Russian or English language Possibility to mark task as finished Interesting features: (I want as more, as possible, while it's OK, if some of them isn't avaliable) Nice and easy-to-use interface Possibility to choose finish time for task. After that it's showed as overdue. Possibility to choose start time for task. Before it task is inactive and maybe shown or hide Possibility to add nested tasks. Task marks completed when all sub-tasks are completed. Possibility to make dependencies. If A depends on B, and B isn't finished yet, A is inactive as in third feature. Possibility to create task in a moment without fill-all-this-forms Syncronization between version(Android to linux or Android to web) Notification (on Android only) Features, that I'm not interested in: Creating more than one todo list sharing ToDo's I've seen couple of managers. Best I've seen now is Task Coach for Linux, but I don't very like its interface, and there is no version for Android.

    Read the article

  • iptables: How to combine DNAT and SNAT to use a secondary IP address?

    - by Que_273
    There are lots of questions on here about iptables DNAT/SNAT setups but I haven't found one that solves my current problem. I have services bound to the IP address of eth0 (e.g. 192.168.0.20) and I also have a IP address on eth0:0 (192.168.0.40) which is shared with another server. Only one server is active, so this alias interface comes and goes depending on which server is active. In order to get traffic accepted by the service a DNAT rule is used to change the destination IP. iptables -t nat -A PREROUTING -d 192.168.0.40 -p udp --dport 7100 -j DNAT --to-destination 192.168.0.20 I also wish all outbound traffic from this service to appear to come from the shared IP, so that return responses will work in the event of a active-standby failover. iptables -t nat -A POSTROUTING -p udp --sport 7100 -j SNAT --to-source 192.168.0.40 My problem is that the SNAT rule is not always run. Inbound traffic causes a connection tracking entry like this. [root]# conntrack -L -p udp udp 17 170 src=192.168.0.185 dst=192.168.0.40 sport=7100 dport=7100 src=192.168.0.20 dst=192.168.0.185 sport=7100 dport=7100 [ASSURED] mark=0 secmark=0 use=2 which means the POSTROUTING chain is not run and outbound traffic leaves with the real IP address as the source. I am thinking I can set up a NOTRACK rule in the raw table to prevent conntracking for this port number, but is there a better or more efficient way to make this work? Edit - Alternative question: Is there a way (in CentOS/Linux) to have an interface that can be bound to but not used, such that it can be attached to the network or detached when a shared IP address is swapped between servers?

    Read the article

  • Korean characters not appearing in Korean Windows XP computer

    - by user13267
    I am using a Korean software (with a partial English interface) in a Korean Version of Windows XP SP 3 However, in parts of the software, even when I change the interface to Korean, Korean letters show up as random characters, as shown here: This is happening at others parts of the software as well, and I am not sure what is the difference between the places where this is happening, and places where this is not happening. For example, a command button where Korean letters are showing up properly is shown below: This software is a video conferencing software and has a chat feature as well. When I type into the chat box, i can see the Korean letters appear properly at my side, but when I press Enter and send the message, it changes into random characters as shown above in the chat box. What could be the issue here? Could it be a missing font in my computer? Since this is a Korean Windows installation I was hoping everything would work properly by default. What can be done here? EDIT 1: I asked some other people who are using this software, and they think that the problem is at my end, and playing around with the Regional and Language Settings might solve the problem. Also, they suggested I install all the language packs related to Korean display. But it looks like all the language packs have been installed, and my location is set to Korea in Regional and Language Settings in Control Panel, and I still have this problem. Also, I have had similar problems with displaying Korean on an English Windows XP computer. This answer suggested some solutions, but I still do not quite understand exactly what I have to do (at that time I had not fixed the problem, as I later on changed the computer). If I follow that answer, what fonts exactly do I need to install?

    Read the article

  • Problem with connecting two different networks

    - by tanascius
    I have two networks: 192.168.13.0/24 (blue) and 192.168.15.0/24 (green). Computer A is connected to the 13-net, only. Computer B has two interfaces, one in each network. There is third computer that acts like a router and connects the 13-net to the 15-net (only in this direction). Now, I'd like to ping 192.168.15.100 from computer A to B. Unfortunately there is never a reply. But when I use a hub instead of a switch it works. In my opinion the ping packet travels through the switch to the router (which is the default route/gateway for A). The router sends the packet back to the switch to B. Probably B receives it on its 15-net interface but answers with it's 15th interface? Is this possible? The problem is, that B may have only a gateway 192.168.13.50 - but I am not really sure of it (B is a embedded system with limited configuration possibilities). Can anyone explain what happens here? Thank you!

    Read the article

  • What does the 'Burst Rate' stat mean in HDTune?

    - by UpTheCreek
    I recently upgraded my laptop's v slow hard drive to a seagate momentus 7200. Everything is working fine, but I'm a bit confused by these benchmark results: The burst rate is significantly less than the Maximim transfer rate, and not much higher than the normal minimum (if you ignore the spikes). What's going on here? On the HDtune website it defines Burst Rate as: ...the highest speed (in megabytes per second) at which data can be transferred from the drive interface (IDE or SCSI for example) to the operating system. Which begs some questions... e.g. if this is the highest, then how did the bechmarking tool record the 103MB/sec maximum? And if this really is the true maximum, then where is the bottleneck? The laptops SATA interface is on an Intel 82801GBM southbridge controller. When I check in hardware manager, I see that it's driver is iaStor.sys from 2005. Maybe that's the issue? I'll look for a newever version, but any insights would be appreciated. Thanks

    Read the article

  • Connect USB hard drive to wireless router on RJ45 port? Possible?

    - by lawphotog
    just a quick story behind. I was trying to set up wireless networked hard drive at home. My wireless router doesn't take USB. I am considering few options. First i was considering to get something like WD My Cloud. My router is an old one provided by service provider. It only has 10/100 Ethernet. WD My Cloud has Gigabit interface. So unless i changed a new router, data transfer will be slow. So upgrading the router is a must if i want fast transfer speed. Plus I already own an external hard drive with USB 3.0 interface. So if I get a router like Netgear D6300, i can get a decent speed wireless shared drive at home. And i can use my existing HDD instead of WD My Cloud. But the router isn't cheap so I am saving up for that. In the meantime I found out the existence of USB to RJ45 adaptor. I read the reviews and some say it works for them and for some don't. They didn't really say what they were trying to do so I'm confused. So if i bought an adaptor like this, can i connect my existing HDD (USB) with my existing router (RJ45) and use it as a shared drive for data transfer? I know it will be slow as the adaptor will only have USB 2.0 and 10/100 for Ethernet. But it's fine as it's for temporary until i got my new router.

    Read the article

  • Cisco ASA 5505 - InterVLAN NAT Exemptions Implementation not working

    - by Brandon Bearden
    Short version is we cannot communicate between our subnets. We have a Cisco ASA 5505 we are using for our network router. We have a Netgear L3 switch behind that with 10 vlans. Each VLAN is on its own subnet. (10.0.10.x/24, 10.0.11.x/24, etc) So ASA Switch Hosts We have PAT for each subnet to our outside interface. Each subnet NATs out properly. I have NAT exemption enabled for 2 of the subnets (eventually I will need all, but am just testing at the moment). Config is here: http://pastebin.com/pDsG7hsh I have tried multiple ways for the NAT exemption to allow all traffic from our inside VLANS. At this point in time I am trying to get "Engineering" to communicate with all hosts on "AuthUser". I can ping some hosts, but not as many as if I am directly on the interface. I can reach a port 80 service, but not 443. I cannot access anything via hostname or NetBIOS. What am I missing to allow higher security level interfaces to fully communicate with lower security level interfaces? Thx!

    Read the article

  • Linux as a gateway (no NAT)

    - by Hugo
    I'm trying to configure a linux server as a gateway/router, but I can't get it to work, and all information I've managed to find is NAT-related. I have a public IP block for the gateway and devices behind it, so I want the gateway to simply route packets to the internet - again: no NATing! I've managed to get the gateway to access the internet successfully (that was just a matter of configuring the IP and GW), and the computers behind it can communicate with it. [EDIT: more info] This is actually an IPv6 block (2800:40:403::0/48) (but I've found that most utilities and instructions can be easily adapted from IPv4 to IPv6 with little hastle). The server has too ports: wan: 2800:40:403::1/48 lan: 2800:40:403::3/48 One of the computers behind it is connected to it via a switch; 2800:40:403::7/48 The wan interface on the server can ping6 www.google.com without issues. The lan interface on the server and the client can mutually ping each other without issues (as well as SSH, etc). I've tried setting the server as a default gateway for the client, with no luck: client # route -A inet6 add default gw 2800:40:403::3 dev eth1 server # cat /proc/sys/net/ipv6/conf/all/forwarding 1 I don't want any filtering/firewalling/etc, just plain routing. Thanks.

    Read the article

  • Secure NAT setup with iptables

    - by TheBigB
    I have Debian running device that needs to act as an internet-gateway. On top of that I want to provide a firewall that not only blocks inbound traffic, but also outbound traffic. And I figured iptables should be able to do the job. The problem: I've configured NAT properly (I think?), but once I set the default policy to DROP and add rules to for instance allow HTTP traffic from inside the LAN, HTTP is not going through. So basically my rules don't seem to work. Below is the initialization script that I use for iptables. The device has two NICs, respectively eth0 (the WAN interface) and eth1 (the LAN interface). echo 1 > /proc/sys/net/ipv4/ip_forward # Flush tables iptables -F iptables -t nat -F # Set policies iptables -P INPUT DROP iptables -P OUTPUT DROP # NAT iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -A FORWARD -i eth0 -o eth1 -m state --state RELATED,ESTABLISHED -j ACCEPT # Allow outbound HTTP from LAN? iptables -A FORWARD -i eth1 -o eth0 -p tcp --dport 80 -j ACCEPT iptables -A OUTPUT -p tcp --dport 80 -j ACCEPT Can anyone shed some light on this?

    Read the article

  • LMDE detects a wireless card, but can't use it

    - by Davidos
    LMDE can see my wireless card, and correctly identifies it, but it refuses to let me turn it on through the shiny graphical interface. Is there a way to use the non-shiny terminal to turn on my wireless? One small tidbit I noticed was the stated version; it says the version is 00. I believe that's hexadecimal for 0, which may indicate something screwy with the software. It would be nice if someone could tell me how to figure out how to solve this kind of problem in the future. *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 00 serial: 91:e3:7b:0d:a3:a9 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-1-amd64 firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:e1d00000-e1d01fff I've tested multiple other network managers, and none of them work. W ireless switch is on, I'm sure it's a driver problem.

    Read the article

  • Low 'Burst Rate' from SATA drive in HDTune?

    - by UpTheCreek
    I recently upgraded my laptop's v slow hard drive to a seagate momentus 7200. Everything is working fine, but I'm a bit confused by these benchmark results: The burst rate is significantly less than the Maximim transfer rate, and not much higher than the normal minimum (if you ignore the spikes). What's going on here? On the HDtune website it defines Burst Rate as: ...the highest speed (in megabytes per second) at which data can be transferred from the drive interface (IDE or SCSI for example) to the operating system. Which begs some questions... e.g. if this is the highest, then how did the bechmarking tool record the 103MB/sec maximum? And if this really is the true maximum, then where is the bottleneck? The laptops SATA interface is on an Intel 82801GBM southbridge controller. When I check in hardware manager, I see that it's driver is iaStor.sys from 2005. Maybe that's the issue? I'll look for a newever version, but any insights would be appreciated. Thanks UPDATE: Acorting to this page on the HDTune website... An important parameter of the test is the Burst Rate. This value should always be higher than the maximum transfer rate. A lower value is usually an indication of a configuration problem. So what might be the configuration problem?

    Read the article

  • Mercurial no longer working in NetBeans?

    - by John Isaacks
    I have been using Mercurial inside NetBeans for a while now. For the past few weeks now Windows Explorer has been crashing for various reasons, including every time I right click. Finally someone suggested I try uninstalling TourtoiseSVN and TortoiseHG since they affect Windows Explorer directly. I uninstalled both last week since I don't ever use them (I either user the NetBeans interface or use the command line interface.) Since then my Windows Explorer stopped crashing. Today I noticed that in NetBeans it is no longer showing me any of the Mercurial features. I pull up a command prompt and its not working their either. It seems like uninstalling TortoiseHG also uninstalled Mercurial altogether, which was not intended. I went to http://mercurial.selenic.com/wiki/Download to download the 64bit 1.8.4 .exe version of Mercurial for Windows. I installed it, and I can now use the command line. However it is still now working in NetBeans. Does NetBeans require Tortoise to work? Is there something else I am missing?

    Read the article

  • Reverse NAT Setup for Hyper-V on Win 2008 R2

    - by sukru
    I'm trying to setup a Linux server behind a Windows Hyper-V host that will help supply some of the services (SSH, HTTPS, etc). However getting RRAS configured for reverse NAT (port forwarding) turned out to be a non trivial task. As a staring point, I tried forwarding port 22 (SSH) to the virtual machine. The virtual machine is on a public interface (i.e.: it also has a visible IP on the same network as the host). On RRAS management console I tried to add a rule, by adding "Local Area Connection" to NAT pool (Public Interface - Enable Nat), and an incoming rule for port 22 - :22. I also tried with the same port enabled on Windows Firewall (and not). The NAT management page tells there are "1 mappings" and "30+ Outbound packets transleted". However all other counters (Inbound packets translated, and respective rejected ones) are always zero. (I'm trying to access the server from an external machine). I can directly access the service if I give the VM's public IP, but not the host's one. Is there a way to enable this on RRAS?

    Read the article

  • Where is SQLite on Nokia N810? How to get?

    - by klausnrooster
    I need SQLite3 with the TCL interface for a simple command-line app I use on all my PCs and want to use on my new (to me) Nokia N810. But "find" does not find any SQLite on the Nokia N810. Several apps use it, supposedly, like the maps/gps (poi.db), and others. I got sudo gainroot before using find, tried with wildcards * and dot . No luck. I guess it's embedded in the apps that use it? The N810's app manager doesn't offer SQLite. Apt-get has it and then fails with error: "Unable to fetch some archives, ..." The "update" and "--fix-missing" options do not help. I don't really want to get scratchbox and compile SQLite and TCL extension for it from sources. I looked at README and it seems like it might be straightforward. However [1] it's not clear what scratchbox download I would need (there are dozens in the Index of /download/files/sbox-releases/hathor/deb/i386), [2] I've never compiled any C sources successfully before, [3] and the whole mess entails a lot of learning curve for what is a very small one-off personal project. http://www.gronmayer.com/ has a few (sqlite (v. 2.8.17-4), libsqlite0 (v. 2.8.17-4), and libsqlite0-dev (v. 2.8.17-4)) but they appear to part of some huge package, may or may not include the TCL interface, ... and no I don't want to port my tiny app to Python. Is there some option I've overlooked? Must I get scratchbox and compile for ARM myself? Thanks for your time.

    Read the article

  • Xen HVM Windows 2008 network bridge

    - by JavierMartinz
    I have a problem with the Windows Server 2008 guest (hvm). I can't get a network interface running for him. I also have a Debian guest and it's working ok, but I can't do it with the Win2k8 guest. When I started the VM, the machine freezes and I can't connect by ssh to the host. /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 188.165.B.C netmask 255.255.255.0 network 188.165.B.0 broadcast 188.165.255.255 gateway 188.165.B.254 brctl show bridge name bridge id STP enabled interfaces eth0 8000.e840f20acc28 no peth0 /etc/xen/xend-config.sxp ... (vif-script vif-bridge) (network-script 'network-bridge') ... /etc/xen/win2k8.cfg # Networking # vif = [ 'ip=5.39.F.G,mac=yy:yy:yy:yy:yy:yy,type=ioemu,bridge=eth0' ] /etc/xen/debian.cfg # Networking # vif = [ 'ip=178.33.D.E,mac=xx:xx:xx:xx:xx:xx' ] As you can see, in the Debian guest I only have to specify an IP address and a MAC. But if I put that in the Win2k8 guest, the machine does not start. I am using Xen 4.0

    Read the article

  • Linux: Three default gateways?

    - by Daniel
    My server has three default gateways, how can that be? Shouldn't there be one default gw? I have three NICs, each attached to a separate subnet: server1:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.5.0.0 * 255.255.255.224 U 0 0 0 eth3 localnet * 255.255.255.224 U 0 0 0 eth0 192.168.8.0 * 255.255.255.192 U 0 0 0 eth1 default 10.5.0.1 0.0.0.0 UG 0 0 0 eth3 default 192.168.8.1 0.0.0.0 UG 0 0 0 eth1 default 10.1.0.1 0.0.0.0 UG 0 0 0 eth0 Sometimes, I can't ping a host on the Internet, sometimes I can. What I want is traffic to the Internet (0.0.0.0) routed through a specific NIC. Can I just add a route for 0.0.0.0 and default gw to one of the eth0-3 interfaces? Will it break my connection? I'm using Debian, here is my /etc/network/interfaces: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 10.1.0.4 netmask 255.255.255.224 network 10.1.0.0 broadcast 10.1.0.31 gateway 10.1.0.1 allow-hotplug eth1 iface eth1 inet static address 192.168.8.4 netmask 255.255.255.192 network 192.168.8.0 broadcast 192.168.8.63 gateway 192.168.8.1 allow-hotplug eth3 iface eth3 inet static address 10.5.0.4 netmask 255.255.255.224 network 10.5.0.0 broadcast 10.5.0.31 gateway 10.5.0.1

    Read the article

  • OpenVPN / iptables restrict some access

    - by RitonLaJoie
    I want to create an openvpn service on a dedicated server I have, for some friends so that they are able to play online games faster. Is there an easy way to restrict which traffic I allow them with iptables ? It seems iptable is not very easy to maintain and we can easily get kicked out of our own server. Rebooting on a rescue mode every time I would get kicked out because of bad iptable rules would just be a pain. As far as I understand, the tun interface would be providing the access. Which kind of rule in iptables would I have to implement to restrict their access to only 1 ip ? Also, I don't want this vpn to be the default gateway for all the traffic. I guess I should go with the option of pushing a route to the clients so that they connect to the IP of the game server through the VPN and use their regular routes through their ISP for all the other traffic ? As a side not, it seems Openvpn AS is not very robust. Is there some other (commercial is ok) product that would give me the same administration options through a web interface ? Is Webmin the only other solution ? Thanks !

    Read the article

< Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >