Search Results

Search found 12497 results on 500 pages for 'linked servers'.

Page 23/500 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• compiling Boost linked libraries (Ubuntu)

  - by Adam Greenhall

  I installed Boost via sudo apt-get install libboost-all-dev on the most recent version of Ubuntu. Now I want to compile a project that uses the Boost.Serialization library, which needs to be linked. I've tried many variants of the following, without success: gcc -I /usr/lib code.cpp -o compiled /usr/lib/libboost_serialization.a and gcc -I /usr/lib code.cpp -o compiled -l libboost_serialization The error message is: error: ‘split_member’ is not a member of ‘boost::serialization ` What am I missing?

  Read the article

• Pfsense 2.1 OpenVPN can't reach servers on the LAN

  - by Lucas Kauffman

  I have a small network set up like this: I have a Pfsense for connecting my servers to the WAN, they are using NAT from the LAN - WAN. I have an OpenVPN server using TAP to allow remote workers to be put on the same LAN network as the servers. They connect through the WAN IP to the OVPN interface. The LAN interface also servers as the gateway for the servers to get internet connection and has an IP of 10.25.255.254 The OVPN Interface and the LAN interface are bridged in BR0 Server A has an IP of 10.25.255.1 and is able to connect the internet Client A is connecting through the VPN and is assigned an IP address on its TAP interface of 10.25.24.1 (I reserved a /24 within the 10.25.0.0/16 for VPN clients) Firewall currently allows any-any connection OVPN towards LAN and vice versa Currently when I connect, all routes seem fine on the client side: Destination Gateway Genmask Flags Metric Ref Use Iface 300.300.300.300 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.25.0.0 10.25.255.254 255.255.0.0 UG 0 0 0 tap0 10.25.0.0 0.0.0.0 255.255.0.0 U 0 0 0 tap0 0.0.0.0 300.300.300.300 0.0.0.0 UG 0 0 0 eth0 I can ping the LAN interface: root@server:# ping 10.25.255.254 PING 10.25.255.254 (10.25.255.254) 56(84) bytes of data. 64 bytes from 10.25.255.254: icmp_req=1 ttl=64 time=7.65 ms 64 bytes from 10.25.255.254: icmp_req=2 ttl=64 time=7.49 ms 64 bytes from 10.25.255.254: icmp_req=3 ttl=64 time=7.69 ms 64 bytes from 10.25.255.254: icmp_req=4 ttl=64 time=7.31 ms 64 bytes from 10.25.255.254: icmp_req=5 ttl=64 time=7.52 ms 64 bytes from 10.25.255.254: icmp_req=6 ttl=64 time=7.42 ms But I can't ping past the LAN interface: root@server:# ping 10.25.255.1 PING 10.25.255.1 (10.25.255.1) 56(84) bytes of data. From 10.25.255.254: icmp_seq=1 Redirect Host(New nexthop: 10.25.255.1) From 10.25.255.254: icmp_seq=2 Redirect Host(New nexthop: 10.25.255.1) I ran a tcpdump on my em1 interface (LAN interface which has the IP of 10.25.255.254) tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on em1, link-type EN10MB (Ethernet), capture size 96 bytes 08:21:13.449222 IP 10.25.24.1 > 10.25.255.1: ICMP echo request, id 23623, seq 10, length 64 08:21:13.458211 ARP, Request who-has 10.25.255.1 tell 10.25.24.1, length 28 08:21:14.450541 IP 10.25.24.1 > 10.25.255.1: ICMP echo request, id 23623, seq 11, length 64 08:21:14.458431 ARP, Request who-has 10.25.255.1 tell 10.25.24.1, length 28 08:21:15.451794 IP 10.25.24.1 > 10.25.255.1: ICMP echo request, id 23623, seq 12, length 64 08:21:15.458530 ARP, Request who-has 10.25.255.1 tell 10.25.24.1, length 28 08:21:16.453203 IP 10.25.24.1 > 10.25.255.1: ICMP echo request, id 23623, seq 13, length 64 So traffic is reaching the LAN interface, but it's not getting passed it. But no answer from the 10.25.255.1 host. I'm not sure what I'm missing.

  Read the article

• Recursion in assembly?

  - by Davis

  I'm trying to get a better grasp of assembly, and I am a little confused about how to recursively call functions when I have to deal with registers, popping/pushing, etc. I am embedding x86 assembly in C++. Here I am trying to make a method which given an array of integers will build a linked list containing these integers in the order they appear in the array. I am doing this by calling a recursive function: insertElem (struct elem *head, struct elem *newElem, int data) -head: head of the list -data: the number that will be inserted at the end of a list -newElem: points to the location in memory where I will store the new element (data field) My problem is that I keep overwriting the registers instead of a typical linked list. For example, if I give it an array {2,3,1,8,3,9} my linked-list will return the first element (head) and only the last element, because the elements keep overwriting each other after head is no longer null. So here my linked list looks something like: 2--9 instead of 2--3--1--8--3--9 I feel like I don't have a grasp on how to organize and handle the registers. newElem is in EBX and just keeps getting rewritten. Thanks in advance!

  Read the article

• What is wrong with this append func in C

  - by LuckySlevin

  My Struct Definitions. typedef struct inner_list {char word[100]; inner_list*next;} inner_list; typedef struct outer_list { char word [100]; inner_list * head; outer_list * next; } outer_list; And The problem part: void append(outer_list **q,char num[100],inner_list *p) { outer_list *temp,*r; temp = *q; char *str; if(*q==NULL) { temp = (outer_list *)malloc(sizeof(outer_list)); strcpy(temp->word,num); temp->head = p; temp->next=NULL; *q=temp; } else { temp = *q; while(temp->next !=NULL) { temp=temp->next; } r = (outer_list *)malloc(sizeof(outer_list)); strcpy(r->word,num); temp->head = p; r->next=NULL; temp->next=r; } } I don't know what is i'm doing wrong in this append function i'm sending a char array and a linked list to be stored another linked list. But i can't store the linked list in another linked list. I couldn't figure out the problem. Any ideas?

  Read the article

• Is it safe to block redirected (but still linked) URLs with robots.txt?

  - by Edgar Quintero

  I have a website that has all URLs optimized and 301 redirected from nasty URLs to clean ones. However, everywhere throughout the site the unclean URLs are linked in menus, content, products, etc. Google currently has all clean URLs indexed, along with a few unclean URLs too. So the site still has linked everywhere the old URLs (ideally this wouldn't be the case but this is how it is ATM). I would like to block the unclean URLs with robots.txt. The question: if I block these unclean URLs with the robots.txt, when the entire website is linked with them (but they all redirect to the clean version), will this affect the indexing status at all?

  Read the article

• Setting value for autocomplete search field linked to Google Places API

  - by user1653350

  I have a web page where people will be able to enter multiple destinations. When they state they want to enter a new destination, the current field values are stored in arrays. If they choose to go back to a previous destination, the relevant values are reinserted into the form fields. I am using the search field linked to autocomplete as the visible display of the destination. When I attempt to put a value into the linked search field, the value is presented as if it is a placeholder instead of a value. Enter the field and the value is removed by the onFocus() event of the Google Places autocomplete add-in. How can I reinsert the value and have it recognised as a value instead of placeholder. field definition in the form <label for="GoogleDestSrch" class="inputText">Destination: <span id="DestinationDisplay2">1</span> <span class="required"><font size="5"> * </font></span></label> <input id="GoogleDestSrch" type="text" size="50" placeholder="Please enter your destination" /> initialise code for Google Places API listener var input = document.getElementById('GoogleDestSrch'); var autocomplete = new google.maps.places.Autocomplete(input); google.maps.event.addListener(autocomplete, 'place_changed', function() { fillInAddress(); }); attempting to reinsert value into search field when prior destination reloaded form.GoogleDestSrch.value = GoogleDestSrch[index]; Issue With Google Places <script language="JavaScript" type="text/javascript"> function GotoDestination(index) { var domove = true; if (index == 0) { index = lastIndex + 1; } else { if (index == -1) { index = lastIndex - 1; if (index == 0) { index = 1; domove = false; } } } if (domove) { if (index != lastIndex) { var doc = window.document; var pdbutton = doc.getElementById("pdbutton"); var pdbutton1 = doc.getElementById("pdbutton1"); if ((index > lastIndex)) { // move to next destination saveDataF(lastIndex); loadDataF(index); lastIndex = index; } else if (index <= lastIndex) { // move to previous destination saveDataF(lastIndex); loadDataF(index); lastIndex = index; } } } } var input; var autocomplete; // fill in the Google metadata when a destination is selected function fillInAddress() { var strFullValue = ''; var strFullGeoValue = ''; var place = autocomplete.getPlace(); document.getElementById("GoogleType").value = place.types[0]; } function saveDataF(index) { var fieldValue; var blankSearch = "Please enter"; // placeholder text for Google Places fieldValue = document.getElementById("GoogleDestSrch").value; if (fieldValue.indexOf(blankSearch) > -1) { fieldValue = ""; } GoogleDestSrch[index] = fieldValue; } function loadDataF(index) { if ((GoogleDestSrch[index] + "") == "undefined") { document.getElementById("GoogleDestSrch").value = ""; } else { document.getElementById("GoogleDestSrch").value = GoogleDestSrch[index]; } } // -- Destination: 1 * Type of place // input = document.getElementById('GoogleDestSrch'); autocomplete = new google.maps.places.Autocomplete(input); google.maps.event.addListener(autocomplete, 'place_changed', function () { fillInAddress(); }); //]]

  Read the article

• User cannot access a system DSN on Windows Server 2008

  - by Ra Osolage

  We run our SQL Server services using a low privileged domain account. That account is NOT a local admin on the OS. Only access I give the user account is assigned during install of SQL: full control over its mount points and then everything else is granted by the SQL Server 2005/2008 installer. I need to create a linked server in SQL Server 2008 to an ODBC data source. So I remoted into the computer using my domain account, which is part of a group that DOES have local admin privs to the OS. I created a system DSN and configured it to connect to another SQL Server. The DSN works perfectly when I test it. However, when I try to create the linked server, I get an error. It appears to me that the DSN is invisible to the domain account that SQL Server is running as. It seems that this problem is only happening to me on Windows 2008 servers. Does anybody know whether there's anything that you need to do after creating a DSN to make it visible for other users to access?

  Read the article

• User cannot access a system DSN on Windows Server 2008

  - by Ra Osolage

  We run our SQL Server services using a low privileged domain account. That account is NOT a local admin on the OS. Only access I give the user account is assigned during install of SQL: full control over its mount points and then everything else is granted by the SQL Server 2005/2008 installer. I need to create a linked server in SQL Server 2008 to an ODBC data source. So I remoted into the computer using my domain account, which is part of a group that DOES have local admin privs to the OS. I created a system DSN and configured it to connect to another SQL Server. The DSN works perfectly when I test it. However, when I try to create the linked server, I get an error. It appears to me that the DSN is invisible to the domain account that SQL Server is running as. It seems that this problem is only happening to me on Windows 2008 servers. Does anybody know whether there's anything that you need to do after creating a DSN to make it visible for other users to access?

  Read the article

• "power limit notification" clobbering on 12G Dell servers with RHEL6

  - by Andrew B

  Server: Poweredge r620 OS: RHEL 6.4 Kernel: 2.6.32-358.18.1.el6.x86_64 I'm experiencing application alarms in my production environment. Critical CPU hungry processes are being starved of resources and causing a processing backlog. The problem is happening on all the 12th Generation Dell servers (r620s) in a recently deployed cluster. As near as I can tell, instances of this happening are matching up to peak CPU utilization, accompanied by massive amounts of "power limit notification" spam in dmesg. An excerpt of one of these events: Nov 7 10:15:15 someserver [.crit] CPU12: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU0: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU6: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU14: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU18: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU2: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU4: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU16: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU0: Package power limit notification (total events = 11) Nov 7 10:15:15 someserver [.crit] CPU6: Package power limit notification (total events = 13) Nov 7 10:15:15 someserver [.crit] CPU14: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU18: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU20: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU8: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU2: Package power limit notification (total events = 12) Nov 7 10:15:15 someserver [.crit] CPU10: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU22: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU4: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU16: Package power limit notification (total events = 13) Nov 7 10:15:15 someserver [.crit] CPU20: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU8: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU10: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU22: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU15: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU3: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU1: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU5: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU17: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU13: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU15: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU3: Package power limit notification (total events = 374) Nov 7 10:15:15 someserver [.crit] CPU1: Package power limit notification (total events = 376) Nov 7 10:15:15 someserver [.crit] CPU5: Package power limit notification (total events = 376) Nov 7 10:15:15 someserver [.crit] CPU7: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU19: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU17: Package power limit notification (total events = 377) Nov 7 10:15:15 someserver [.crit] CPU9: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU21: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU23: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU11: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU13: Package power limit notification (total events = 376) Nov 7 10:15:15 someserver [.crit] CPU7: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU19: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU9: Package power limit notification (total events = 374) Nov 7 10:15:15 someserver [.crit] CPU21: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU23: Package power limit notification (total events = 374) A little Google Fu reveals that this is typically associated with the CPU running hot, or voltage regulation kicking in. I don't think that's what is happening though. Temperature sensors for all servers in the cluster are running fine, Power Cap Policy is disabled in the iDRAC, and my System Profile is set to "Performance" on all of these servers: # omreport chassis biossetup | grep -A10 'System Profile' System Profile Settings ------------------------------------------ System Profile : Performance CPU Power Management : Maximum Performance Memory Frequency : Maximum Performance Turbo Boost : Enabled C1E : Disabled C States : Disabled Monitor/Mwait : Enabled Memory Patrol Scrub : Standard Memory Refresh Rate : 1x Memory Operating Voltage : Auto Collaborative CPU Performance Control : Disabled A Dell mailing list post describes the symptoms almost perfectly. Dell suggested that the author try using the Performance profile, but that didn't help. He ended up applying some settings in Dell's guide for configuring a server for low latency environments and one of those settings (or a combination thereof) seems to have fixed the problem. Kernel.org bug #36182 notes that power-limit interrupt debugging was enabled by default, which is causing performance degradation in scenarios where CPU voltage regulation is kicking in. A RHN KB article (RHN login required) mentions a problem impacting PE r620 and r720 servers not running the Performance profile, and recommends an update to a kernel released two weeks ago. ...Except we are running the Performance profile... Everything I can find online is running me in circles here. What's the heck is going on?

  Read the article

• Good idea to use NLB for DNS servers?

  - by I.T. Support

  Is it a good idea to use NLB to load balance DNS requests to primary and secondary dns servers on port 53?

  Read the article

• Bidirectional real-time sync of large file tree between two distant linux servers

  - by dlo

  By large file tree I mean about 200k files, and growing all the time. A relatively small number of files are being changed in any given hour though. By bidirectional I mean that changes may occur on either server and need to be pushed to the other, so rsync doesn't seem appropriate. By distant I mean that the servers are both in data centers, but geographically remote from each other. Currently there are only 2 servers, but that may expand over time. By real-time, it's ok for there to be a little latency between syncing, but running a cron every 1-2 minutes doesn't seem right, since a very small fraction of files may change in any given hour, let alone minute. EDIT: This is running on VPS's so I might be limited on the kinds of kernel-level stuff I can do. Also, the VPS's are not resource-rich, so I'd shy away from solutions that require lots of ram (like Gluster?). What's the best / most "accepted" approach to get this done? This seems like it would be a common need, but I haven't been able to find a generally accepted approach yet, which was surprising. (I'm seeking the safety of the masses. :) I've come across lsyncd to trigger a sync at the filesystem change level. That seems clever though not super common, and I'm a bit confused by the various lsyncd approaches. There's just using lsyncd with rsync, but it seems this could be fragile for bidirectionality since rsync doesn't have a notion of memory (eg- to know whether a deleted file on A should be deleted on B or whether it's a new file on B that should be copied to A). lipsync appears to be just a lsyncd+rsync implementation, right? Then there's using lsyncd with csync2, like this: http://www.axivo.com/community/threads/lightning-fast-synchronization-with-csync2-and-lsyncd.121/ ... I'm leaning towards this approach, but csync2 is a little quirky, though I did do a successful test of it. I'm mostly concerned that I haven't been able to find a lot of community confirmation of this method. People on here seem to like Unison a lot, but it seems that it is no longer under active development and it's not clear that it has an automatic trigger like lsyncd. I've seen Gluster mentioned, but maybe overkill for what I need? UPDATE: fyi- I ended up going with the original solution I mentioned: lsyncd+csync2. It seems to work quite well, and I like the architectural approach of having the servers be very loosely joined, so that each server can operate indefinitely on its own regardless of the link quality between them.

  Read the article

• OpenDNS servers initial response is very slow

  - by Ben Collins

  I've got a Time Warner cable ISP package (RoadRunner), and the modem they gave me doesn't allow me to specify which DNS servers to use; it always uses whatever the upstream dhcp server gives it. I prefer to use OpenDNS on my home network, so i've configured a couple of my PCs manually in the Windows adapter settings for IPv4 such that their IP addresses are obtained via DHCP, but the DNS server settings are fixed to the OpenDNS server IPs. Now, when I startup Windows on these PCs, it always takes 2-3 minutes to start receiving responses from the DNS servers; any request before that times out. While not debilitating, this is quite annoying. Any ideas why this might be happening?

  Read the article

• How to distribute email's delivery between 2 or more servers

  - by user181186

  We provide Email Marketing service through our online App. We have about 30 customers. And each one has it's own mailling list (5k to 20k emails each). What we really want is to distribute email's delivery between 2 or more servers. I was wondering What kind of aproach/solutions MailChimp , Constant Contact uses to provide a great service ? use many servers ? many IPs ? Our spam policy suspends ANY user/customer that gets 10% bounced .

  Read the article

• Name Servers changed over 48 hrs ago and site is still down

  - by Solomon Closson

  Ok, I just recently changed Name Servers for my site (Oct. 29th): http://dream-portal.net but there is an issue, the name servers were changed from godaddy, however, the DNS is being hosted elsewhere. Godaddy states that the DNS is resolving the site to www.dream-portal.net and that is making it inaccessible from the DNS on the other host and that they can't do anything because I'm not hosting DNS with godaddy. I've contacted the other host and they say that everything is fine, however, people are not able to access the site and I can't access it from my work computer. I can only access it from my home computer. From my work computer it says that the page can not be found. What should I do? What can I do? Other people reported problems with the site here: http://www.simplemachines.org/community/index.php?topic=487592.msg3629960#msg3629960

  Read the article

• Query two different Servers

  - by Felipe Fiali

  I have to query two different servers from a dynamically built query. It basically gets data from one server, treats it, and inserts it into another server. The only problem is I have to be sure it works for both situations: If both the source and destination databases are on the same server, and if they're not. I understand the concept of using Linked Servers in SQL Server, but I cannot think of a way to consider both alternatives, same server and different servers. A little help?

  Read the article

• Should my servers boot from VHD?

  - by tony roth

  I've been testing native vhd boot on several servers. It seems to be pretty transparent in terms of deployment and with my seat of the pants testing I have not noticed any difference in performance. The main reason that I want to boot vhd is due to their transportablility between different hardware and to hyper-v servers. the following roles will be installed. dfsr dhcp iis application server dc <- haven't tested this yet but see no reason why it won't work. With the above low impact (in terms of performance) roles do you thing booting from VHD is appropriate. thx

  Read the article

• Migrating master-slave MySQL database servers to 2 new servers, any tips or suggestions?

  - by mmattax

  I'm setting up 2 new database servers that will be replacing a current master-slave setup. All boxes are running / will be running MySQL on RHEL. Our current naming conventions: db1 - master database db2 - slave (using MySQL replication) db01 - new master db02 - new slave We need to get db01 to be the new master with db02 as the new slave. What is the best way to migrate db1 and db2 to db01 and db02? db1 and db2 are running in a production setting and we need to minimize all downtime; db1 has roughly 30GB of data in the database. Any suggestions or tips on how to migrate to our new servers would be much appreciated.

  Read the article

• W2k8 RC1: Windows Media Servers (WMS) as proxy

  - by da_didi

  (fullquote from stackoverflow.com/questions/2690788/w2k8-rc1-windows-media-servers-wms-as-proxy/2690791#2690791) I will have one streaming-server (W2k8, unknown streaming protocol [rtsp, mss, http]) and half dozen streaming-servers as proxies to save bandwidth. I have read the documentation and installed the modules, but I am unsure how I have to configure the proxy's according to http://technet.microsoft.com/de-de/library/ee126142(en-us,WS.10).aspx - as a proxy or reverse proxy and how I minimize the bandwidth needs between origin server and proxy's. What is the best way to realize my setup? Any short how-tos? How can I announce all players to use the proxy? Route all rtsp/mms/http-requests through my proxy? Announce the proxy with DHCP-releases? Thanks!

  Read the article

• Installing Windows on HP Proliant Servers without SmartStart

  - by Fitzroy

  I have a PXE server for deploying Windows XP and Windows 7 to workstations. The process is as follows: Boot the workstation from the NIC. Workstation sends a DHCP request. DHCP server responds with an IP address and the location of the PXE server. Workstation downloads WinPE image file from PXE server via TFTP Workstation stores WinPE image file in memory and executes it. Once booted into WinPE, I connect to a network share to gain access to either the Windows XP or Windows 7 installation files. A custom script is launched to guide you through the process of formatting and partitioning the hard drive(s) (using DISKPART and FORMAT). Another custom script asks for details such as the hostname to assign to the workstation. The answers provided are used to build an unattended answer file (SIF [Setup Information File] for WinXP and XML for Win7). The Windows setup EXE is launched, passing the unattended answer file to it as a parameter. The Windows XP and Windows 7 installation sources have been customised to include the drivers for our Dell workstations. They also run a number of scripts upon first booting up to install software packages. This process works very well for our workstations and I would now like to use it for building our servers too. The vast majority of our servers are HP Proliant DL360 G6, DL380 G5 and DL380 G6. They’re running Windows Server 2003 (various editions) or 2008 (various editions). To date, we have always built the HP Proliant servers using the SmartStart CD provided. SmartStart does three useful things for us: Setup RAID with HP Array Configuration Utility (ACU). Installs and configures SNMP Installs various HP Tools for Windows (HP Array Configuration Utility, HP Array Diagnostic Utility, HP Proliant Integrated Management Log Viewer, etc) Using SmartStart I have never had to manually download and install Windows drivers for network, sound, video, etc. I'm not sure if this is because SmartStart copies drivers from the CD during setup, or whether Windows just has the drivers natively in its driver CAB. If I abandon the SmartStart CD in favour of my PXE server I would have to do the following: As I wont have access to ACU, I'll configure the RAID (before booting to the PXE server) by pressing F8 (during the boot process) to access Option ROM Configuration for Arrays (ORCA). Installation of SNMP and the HP Tools will have to be installed once the Windows installation is complete using the Proliant Support Pack. Is this method OK? Is there anything that the SmartStart CD does that I'll be unable to do by other means? Are there any disadvantages to not using the SmartStart CD? Many thanks. UPDATE 05/01/12 I’ve been reading through the SmartStart Scripting Toolkit documentation. The scripting toolkit contains command line tools which work within WinPE and can such things as configure BIOS settings, configure an array and setup ILO. I’m personally not too bothered about configuring BIOS settings as I rarely deviate from the defaults (unless the server is to be a Hyper-V host). I’m not too fussed about being able to configure the array from within WinPE, as I’m happy to just press F8 and use Option ROM Configuration for Arrays (ORCA). Although, if it’s easy enough to do, I will explore this further, as it saves time if everything can be configured from within WinPE. One of the nice features all the tools possess is that you can pass input files to them. EG. Configure one server to your requirements, capture its configuration to a file (using the appropriate tool), you can then use the tool on other servers passing the input file with the captured configuration. Array controller drivers appear to be included with the toolkit along with example of how to incorporate them within a WinPE build. I suppose WinPE won’t be able to see logical volumes (I.E 2x physical disks in a RAID 1 configuration) without the array controller drivers? I mentioned in my post that SmartStart normally installs a bunch of Windows HP tools for you. I’ve had a look today, and if you run the SmartStart CD from within Windows all the tools can be installed. Therefore I can do this after the Windows installation is complete. The SmartStart CD appears to contain a lot Windows drivers. I can customise my Windows 2008 source to incorporate these drivers. However, I understand that incorporating an array controller driver is a little different to most drivers. I believe that you have to provide the driver during the very early stages of the Windows setup. I’m working through the Scripting Toolkit documentation to try and work this out...

  Read the article

• Syncronizing multiple exchange servers 2007

  - by Mustafa Ismail Mustafa

  We're introducing a new exchange server for several reasons. After the introduction of the new server, and synchronizing it with the old one (mailboxes, contacts, rules, the whole shebang) we're going to be formatting the old machine, install XenServer 5.5 on it, and create a slices, one of which will have Exchange server, which again will need to be synchronized. Then, we'll have 2 different routes to the mail servers (mx1, mx2) so that if there is an outage on one, the other should be available. So now, I'm wondering how to synch? I can move a mailbox from one server to the other, and I'm sure that can be done in bulk, but that's not what I'm looking for. I'm looking to make both Servers equal, the first time so I can make a backup of the original, and the second time so that they can be made into peers. This is with Exchange 2007 on Windows 2008 R2 (x64) Suggestions? TIA

  Read the article

• run two apache servers on one computer

  - by harry_T

  I would like to run two XAMPP apache servers and mysql on one Windows computer. My first idea was to run one under directory XAMPP, the other under XAMPP_B. Why you ask? I have two applications that have to be in the "root" directory of localhost. Both servers do not have to be active at same time, so I don't think I will have any conflicts I will have to modify my.cnf in mySQL httpd.conf, apache_start and maybe other config files as well. Or maybe someone can suggest a better way...

  Read the article

• Applying the Windows Experience Index to Servers

  - by Scott

  I finally convinced upper management that we need a computer replacement plan, and I've been tasked with making an inventory of what we have and determining what needs to be replaced this year, next year, the year after, etc. I had to use some sort of criteria to back up my recommendations, so I decided to try using the Windows Experience Index. I've determined the CPU and Memory scores for all of our desktops and servers using community data. I also feel fairly successful in assigning a WEI score to each user based on their computing needs. I'm struggling with assigning a WEI score to the various servers that we have: file server, database server, Exchange server, backup server (for doing backups), web server. Suggestions would be appreciated.

  Read the article

• Changing Servers - Redirect to new IP = No Downtime?

  - by Denis Pshenov

  I am changing servers of my website. The IP of old server cannot be moved to the new one. To have no downtime I am planing to do the following, please someone confirm it will work: Setup the new server and listen on the new IP Old server redirect all traffic to the new IP Change DNS records to point to the new IP My logic tells me that when I redirect to the new IP from my old box, the user will not see the domain name in the browser but will see the new IP. Is there a way to redirect to the new IP and send along the HOSTNAME with it so that the user will see the domain name in the browser? Im doing this because the site is in constant use and simply changing DNS settings won't do as database won't be synced between the new and old servers during propagation.

  Read the article

• RSH between servers not working

  - by churnd

  I have two servers: one CentOS 5.8 & one Solaris 10. Both are joined to my workplace AD domain via PBIS-Open. A user will log into the linux server & run an application which issues commands over RSH to the solaris server. Some commands are also run on the linux server, so both are needed. Due to the application these servers are being used for (proprietary GE software), the software on the linux server needs to be able to issue rsh commands to the solaris server on behalf of the user (the user just runs a script & the rest is automatic). However, rsh is not working for the domain users. It does work for a local user, so I believe I have the necessary trust settings between the two servers correct. However, I can rlogin as a domain user from the linux server to the solaris server. SSH works too (how I wish I could use it). Some relevant info: via rlogin: [user@linux~]$ rlogin solaris connect to address 192.168.1.2 port 543: Connection refused Trying krb4 rlogin... connect to address 192.168.1.2 port 543: Connection refused trying normal rlogin (/usr/bin/rlogin) Sun Microsystems Inc. SunOS 5.10 Generic January 2005 solaris% via rsh: [user@linux ~]$ rsh solaris ls connect to address 192.168.1.2 port 544: Connection refused Trying krb4 rsh... connect to address 192.168.1.2 port 544: Connection refused trying normal rsh (/usr/bin/rsh) permission denied. [user@linux ~]$ relevant snippet from /etc/pam.conf on solaris: # # rlogin service (explicit because of pam_rhost_auth) # rlogin auth sufficient pam_rhosts_auth.so.1 rlogin auth requisite pam_lsass.so set_default_repository rlogin auth requisite pam_lsass.so smartcard_prompt try_first_pass rlogin auth requisite pam_authtok_get.so.1 try_first_pass rlogin auth sufficient pam_lsass.so try_first_pass rlogin auth required pam_dhkeys.so.1 rlogin auth required pam_unix_cred.so.1 rlogin auth required pam_unix_auth.so.1 # # Kerberized rlogin service # krlogin auth required pam_unix_cred.so.1 krlogin auth required pam_krb5.so.1 # # rsh service (explicit because of pam_rhost_auth, # and pam_unix_auth for meaningful pam_setcred) # rsh auth sufficient pam_rhosts_auth.so.1 rsh auth required pam_unix_cred.so.1 # # Kerberized rsh service # krsh auth required pam_unix_cred.so.1 krsh auth required pam_krb5.so.1 # I have not really seen anything useful in either system log that seem to be directly related to the failed login attempt. I've tail -f'd /var/adm/messages on solaris & /var/log/messages on linux during the failed attempts & nothing shows up. Maybe I need to be doing something else?

  Read the article

• nginx is not using gzip to talk to backend servers

  - by Michael Gorsuch

  Our web servers are running IIS 7 and are configured to compress dynamic and static content. When I hit these servers directly, gzip compression works. I recently placed nginx in front of them, and gzip compression has stopped. I was able to work around this by explicitly enabling gzip compression on nginx itself, but that seems a little inefficient considering I have half a dozen backends and only one active nginx box. It appears that nginx is stripping out the Accept-Encoding header. Does anyone have any advice for how to 'correct' this behavior? A sample configuration: upstream backend { server 127.0.0.1:8080; } server { listen 80; proxy_set_header Host $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; location / { proxy_pass http://backend; } }

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >