Search Results

Search found 40420 results on 1617 pages for 'power line networking'.

Page 23/1617 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• DD-WRT Router acting as a Switch and Wi-Fi AP

  - by dotnetchris

  Recently I upgraded to Comcast Business and their modem has a built-in router so I took off my DD-WRT router and moved to a location in my home where I needed more ports and Wi-Fi (preferably without running new Ethernet cables since it's 50-100 foot run through floor and ceilings). I have my network cable from my Comcast modem going into Port 1 of my DD-WRT router with Port 2 and 3 being networked PCs. I have DD-WRT setup as a DHCP forwarder with the firewall disabled. This lets my all of my devices access the network fine. Is the correct the way to do this? Or is this a less optimal solution and it should be done in a slightly different way?

  Read the article

• Can't connect to LAN when connected to D-Link DIR-615

  - by Senseful

  I'm have a D-Link DIR-615 Wireless N 300 Router. I didn't use the CD it comes with to set up the network. Instead I configured it manually through the router's settings that are accessed via a web browser. The main changes I made are: Secured the router so that a password is required before clients can use the wireless internet. Broadcasting 802.11N only (not B or G). I can connect to the router just fine and I'm able to access the internet. The only problem is that I don't see any of the other computers in my LAN. When I try connecting to another Wi-Fi router that I have (which is connected to the same network), I can see all of the computer's on my LAN just fine. Therefore, I'm guessing that the reason I can't connect to the LAN is not a problem with my computer and is a problem with the router instead. I'm on a MacBook Air running Mac OS X 10.6.6. I tried contacting D-Link technical support, but they only try to help you if you have problems connecting to the internet. They aren't really concerned with problems that have to do with the accessing PC's on the same network.

  Read the article

• Multiple Wireless Networks via Airport?

  - by Moshe

  Is it possible to to connect to multiple networks at the same time using the AirPort wireless card on my iMac 21.5"?

  Read the article

• How do I get more information on a potential network freeloader?

  - by Dov

  I have a home network set up, complete with a relatively good password. I'm in Mac OS X 10.6 (Snow Leopard) and have been noticing, on occasion, a computer showing up in my Finder's Shared section, that is not one of my own (the "pe-xpjalle" box pictured below). He has a tendency to come and go. How can I figure out his MAC address or something, so I can block him? I checked my "Logs and Statistics" in the Airport Utility, and didn't see that computer under DHCP clients. I'd rather not change my password, since I have quite a few devices I'd have to update. Is there any other reason he's show up on my network besides having guessed my password? Update: I fixed the Dropbox URL above (how embarrassing, I'm new to Dropbox. Thanks for the heads up, Doug.) Update 2: I tried clicking on "Connect as..." just for the hell of it, and got the dialog below. Now I have even less an idea what's going on than before. I don't have Parallels of VMware running, just the following: Transmission, NetNewsWire, Mail, Things, Safari, iTunes, Photoshop, Pages, Yojimbo, Preferences, AppleScript Editor, Software Update, Airport Utility, and Terminal. I don't think any of those create a virtual network machine, right? And no VMware machine of mine has ever had a name resembling "pe-xpjalle". Update 3: I just changed my passwords on both my N- and G-only networks, and I'm still seeing this, so I highly doubt that it's someone who's figured out my password (twice now). I'm really stumped.

  Read the article

• UDP multicast streaming of media content over WIFI

  - by sajad

  I am using vlc to stream media content over wireless network in scenario like this (from content streamer to stream receiver client): The bandwidth of wireless network is 54 Mb/s and UDP stream's required bandwidth is only 4 Mb/s; however there is trouble in receiving media stream and quality of playing specifically in multicast mode; means I can play the stream but it has jitter and does not play smoothly. In uni-cast I can stream up to 5 media streams correctly, but in multicast mode there is problem with streaming just one media! However when I stream from client some multicast streams; the wifi access-point can receive data correctly and I can see the video in "udp streamer" side correctly even when number of multicast streams increases to 9; But as you see I want to stream from streaming server and receive media in client size. Is this a typical problem of streaming real-time contents over wireless networks? Is it necessary to change configurations of my WIFI switch or it is just a software trouble? thank you

  Read the article

• Static DHCP!?

  - by voyager

  I've found some home wireless routers/ADSL+ modems (ZyXEL 660) talking about Static DHCP, when refering to assosiating a specific MAC to an IP, but still serve the configuration over DHCP. Doesn't this have another name? What does Cisco call this feature (that I know supports because I've used long time ago)?

  Read the article

• Configure IPv6 routing

  - by godlark

  I've got IPv6 addresses from SIXXS. My host is connected with SIXXS network over a AICCU tunnel ("sixxs" interface). My host address is 2001:::2, the host on the end has address 2001:::1. On my host IPv6 is fully accessible. I have problem with configuring IPv6 network on VMs. I use VirtualBox, the VM (Ubuntu) uses tap1 (on the host bridged by br0) #!/bin/sh PATH=/sbin:/usr/bin:/bin:/usr/bin:/usr/sbin # create a tap tunctl -t tap1 ip link set up dev tap1 # create the bridge brctl addbr br0 brctl addif br0 tap1 # set the IP address and routing ip link set up dev br0 ip -6 route del 2001:6a0:200:172::/64 dev sixxs ip -6 route add 2001:6a0:200:172::1 dev sixxs ip -6 addr add 2001:6a0:200:172::2/64 dev br0 ip -6 route add 2001:6a0:200:172::2/64 dev br0 Host: routing table: 2001:6a0:200:172::1 dev sixxs metric 1024 2001:6a0:200:172::/64 dev br0 proto kernel metric 256 2001:6a0:200:172::/64 dev br0 metric 1024 2000::/3 dev sixxs metric 1024 fe80::/64 dev eth0 proto kernel metric 256 fe80::/64 dev sixxs proto kernel metric 256 fe80::/64 dev br0 proto kernel metric 256 fe80::/64 dev tap1 proto kernel metric 256 default via 2001:6a0:200:172::1 dev sixxs metric 1024 Guest: interface eth1 (it is connected with tap1): auto eth1 iface eth1 inet6 static address 2001:6a0:200:172::3 netmask 64 gateway 2001:6a0:200:172::2 Guest: routing table 2001:6a0:200:172::/64 dev eth1 proto kernel metric 256 fe80::/64 dev eth0 proto kernel metric 256 fe80::/64 dev eth1 proto kernel metric 256 default via 2001:6a0:200:172::2 dev eth1 metric 1024 The guest pings to the host, the host pings to the guest, the host pings to 2001:6a0:200:172::1, but the guest doesn't ping to 2001:6a0:200:172::1. The guest tries to ping, on the host (by tcdump) I can capture its packets, but the host doesn't send them to 2001:6a0:200:172::1. What have I missed in configuration?

  Read the article

• diagnostic multicast issue using wireshark

  - by Abruzzo Forte e Gentile

  I have a network that is setup for multicast traffic. My setup is the following -Machine A : a server generates multicast traffic. -Machine A : few clients subscribing to that multicast traffic -Machine B : few clients subscribing to that multicast traffic # Address I am using IP : 239.193.0.21 PORT: 20401 The clients in machine A , even if they join the group (I can see IGMP messages through wireshark), don't receive any data while (and this is the funny part) machine B,C and D receive everything. I sorted that issue by completely disabling Linux firewall. Before doing that, I enabled the multicast on the firwall ('reject all'). iptables -A INPUT -m addrtype --src-type MULTICAST -j ACCEPT My question is the following: what I can check in wireshark that can help me in spot such firewall issues in the futures? For TCP/IP I realize by using ping and looking at ICMP packets rejected. What I can check/monitor for multicast? I am using LInux/Red-Hat Enterprise 6.2

  Read the article

• Setting up a wireless network with Verizon MiFi

  - by winarm

  I am trying to set up a home network. I live in a location without cable internet so I have a Verizon MiFi card. I have a few laptops at the moment and they each connect through the card but I want to set up an Ubuntu 10.10 server and see if I can use it for DHCP. I have a Trendnet TEG-S50G switch and the computer I plan to use for the server has a Linksys WMP-11 Wireless PCI card. Is there any other equipment I need in order to get this to work? Is this even doable? Is there a better way to make this happen?

  Read the article

• What's a good, affortable ruter that will not give me problems when downloading torrents?

  - by Lirik

  I found several routers on newegg and they're in the $50-60 range, but I'm not sure if they'll handle the number of connections that are created when downloading torrents (100-300 seeds and around 50 peers). My roommate watches netflix movies, my brother and I download torrents, so my NETGEAR router ends up choking on the traffic and I have to restart it quite frequently. I've already posted a couple of questions on the topic and I've come to the conclusion that I need a new router. What are some routers that I should consider (my budget is in the $50 range)?

  Read the article

• SSH: Tunnel multiple ports to remote server

  - by user1594322

  See attached diagram. Host A - Windows server Host B - Linux server Host C - VMWare ESXi server From host A I can SSH to host B over the VPN tunnel. I can ping host C from host B, but not from host A. I am assuming this is because host C has lost its default gateway. Host C is a VMWware ESXi server, so I would need to tunnel several ports (80,443,902) in order to reach host C from host A. What is the correct ssh syntax to create the tunnel in order to reach host C from host A, and can I do it using a single command, or do I need to run three commands (one for each port, 80,443,902)?

  Read the article

• Share laptop's Wi-Fi with a LAN connection and a mobile device

  - by xperator

  OS: Windows 7 64bit I want to share my laptop's internet connection between my PC and my Android device. But I can only do one of them at a time. The laptop is connected to internet wirelessly. The PC is connected to the laptop using a Ethernet cable and internet is shared between them. I want to connect my mobile device to my laptop by making the laptop into a Wi-Fi hotspot. PC (Ethernet) == Laptop (connected to net by Wi-Fi) <== Mobile device (Wi-Fi hotspot) I have 3 connections in my laptop: Wireless Network Connection (internet - shared) Local area connection (PC) Wireless Network Connection 2 (Wi-Fi hotspot) Every time I have to disable either the LAN to get the Wi-Fi hotspot working, or disable the Wi-Fi hotspot to get LAN working. How can I share so I can use both at the same time?

  Read the article

• Wireless and Wired Network Access at same time?

  - by grasper

  At work, I use a laptop. It is a Dell Latitude D630 with Windows XP. I work in a lab environment where I need to use the Ethernet Port as a Static IP to interact with a local network (which cannot talk to the outside world). What I would like to do is use the Wireless as the internet connection so i can check email, etc at the same time I am using the ethernet network... It seems like this is not possible. Is there a piece of software or a way to configure it to allow me to do this?

  Read the article

• Wireless Router will not allow connection

  - by Chris

  I am working with a RangeMax(TM) Wireless Router WPN824 v2, and it will not allow a wireless connection nor a wired connection. I am at an actual lost, with no way into the router I cannot test settings. I have unplugged it, left it off for a 32 hours, and reset it with no luck. Any ideas? Could the router just be done-zo?

  Read the article

• Setting up a wireless connection

  - by shadeMe

  I've got a DLINK router connected to my ADSL modem that forms the hub of my home network. I've two clients - A desktop with an onboard wireless adaptor and a laptop that's outfitted with the same. The former runs Windows 7 x64, the latter Windows XP x86. I'd like to setup a wireless connection between the two that would allow me play games over to and to a lesser extent, transfer and stream data. How would I go about doing it ?

  Read the article

• Mimic the behavior of a machine added to a domain

  - by Ian

  Hello, For some reason, the IT department at our company does not want to add Windows 7 and Windows Vista machine to the domain controller. I hate to always provide my network credentials everytime I access a shared folder on a machine that is joined to the domain. I also hate to always provide my password when I launch outlook or Visual Studio (Team Explorer). Is there a way to mimic the behavior of a machine that is added to a domain without actually adding the machine in the domain? For shares, I can create a batch file that will NET USE the different fileservers we use here but that is a huge security risk as I will type my password as plaintext. Thanks!

  Read the article

• Copying files from NAS to NAS drives

  - by user1001421

  Very simple question. I've got 2 NAS drive that are "wire" connected via a router. If I have a wireless laptop and request a large amount of data be copied from one NAS drive to the other, does the network traffic go direct from the one drive to the other, going via the wired network, or does the network traffic go via my laptop, if you see what I mean. IE. From the NAS drives wired network, to the wireless network and then back to the wired network. Is this a common bottle-neck when copying a large amount of data? And if so, is there a way to avoid it. Thanks.

  Read the article

• NAT, iptables and problematic ports

  - by Rajie

  I am building a small office network with virtual machines. My schema is this: Computer A: gateway, ip 1.1.1.1, iptables used for NAT [eth0=public internet dhcp, dhcp; eth1=gateway] Computer B: client, ip 1.1.1.2, using gateway from Computer A. NAT is working, and Computer B can access the internet using the A's gateway. I redirected some incoming ports from A to B (for instance, if A receives a request to port 80, it goes automatically to Computer B's Apache). The thing is that I do not really understand how to open/close ports for Computer B from Computer A. I know how to close a port: iptables -A INPUT -p tcp --dport 80 -j DROP And it will refuse all incoming (not output) connections to port 80. However, this works for main interface eth0. I tried to, for instance, drop ingoing and outgoing connections for Computer B, port 80: iptables -A FORWARD -i eth1 -o eth0 -p tcp --dport 80 -j DROP iptables -A FORWARD -i eth0 -o eth1 -p tcp --dport 80 -j DROP But it does not work. And I cannot figure out what I am doing wrong. Any clue?

  Read the article

• Delayed startup of network icon (wi-fi)

  - by Michael Dy

  When my Windows 7 Starter netbook boots up and after everything is loaded, it takes about five minutes before the network icon near the clock becomes functional. When there's an available wi-fi signal (which automatically connects to my netbook as preconfigured) after the boot, my netbook seamlessly connects to it even if the network icon cannot be clicked or accessed. (The icon is shown to be loading for about five minutes.) During this time, when I go to Network and Sharing Center, it takes the same time to load. So even while the icon and the Center cannot be accessed, I can surf the Internet. When my netbook was still new, it didn't have this issue. How do I fix this?

  Read the article

• Issues with ForceBindIP on Windows 7 (x64)

  - by Craig

  I am desperately needing a solution to binding certain applications to specific network interfaces. ForceBindIP seems to be my only solution. Although the website claims it works up to XP, Google says that many users running 7 have had it work successfully. I have UAC disabled, yet still: Does anyone know why this is happening? If not, does anyone know a viable alternative to ForceBindIP? I'm a gamer and I'm addictively trying to torrent on a secondary connection while playing games online.

  Read the article

• Should I use 802.11n with a 15 Mbps ISP (Comcast Cable)?

  - by stackoverflowuser2010

  I currently own a LinkSys-WRT54GL 802.11a/b/g wireless router, and my ISP is Comcast Cable providing me with 15 Mbps (that's bits per second, I believe) download speed. I am wondering if there is any benefit with using an 802.11n wireless router to access the Internet? The maximum theoretical speed of the WRT54GL router is 54 Mbps (802.11g), which is faster than the 15 Mbps provided by my ISP. I know that 802.11n has a max bandwidth of 300 Mbps, and it would help for intra-house transfers, such as streaming video from one computer to another. But is there any benefit to 802.11n for Internet activity, such as web browswing, gaming, and streaming video from Netflix?

  Read the article

• Can't view other computers on Network

  - by Darkart

  Systems: My Machine: Windows 7 Ultimate connected through ethernet into router Her Machine--Other Machine: Windows 7 Ultimate connected through wireless Router:F5D8236-4 N Wireless Router Version 1 Firmware: 2.01.03 (Apr 28 2009) ISP: Comcast Problem: I can not view the "Other Machine" on the network at all. I opened command prompt and ran net view and saw the pc name. I tried pinging the pc and it times out. Went inside the router and tried viewing the computer on the DHCP list and it can not be seen. I restored the router back to default settings and firmware and completely reset the modem and router, and created home group. I went to the other machine to configure home group settings and made sure that both PC's had identical settings. She was able to see my machine but I could not see hers. I restarted both machines and now we cant see each other at all. Also her PC ("Other Machine") had exclamation mark in the wireless icon but was connected just fine. There is no firewalls on currently or anti-virus enabled, and still can not see each other. Right now I am checking for updated drivers for the wireless card, but my question is could it be the router or something hardware related? I have went through all the settings in the Home group and visited most FAQ's and still no luck. Also as it stands I can not view her machine inside the router DHCP Client List :(

  Read the article

• How do I add wireless-router to existing VPN-router>DHCP-server network?

  - by j03lar50n

  Our office just acquired a Cisco/Linksys RVL200 VPN Router for use as our primary router. We handle DHCP serving via dhcpd on a Debian server. I want to enable wireless access to our network. We have a Linksys WRT54G v5- and I'm having some difficulty setting it up to work correctly, please help!

  Read the article

• Ericsson W35 ssh administration

  - by jblaster

  I picked up a Ericsson W35 at a pawn shop the other day and when I login to the administration section at 192.168.1.1 I get an error message about connecting to the database. It apparently supports ssh administration and I get a password prompt when attempting to ssh [email protected] but no passwords I try work and theres no documentation for it. Has anyone had success with ssh on the Ericsson W35 and is this issue fixable? Thanks.

  Read the article

• How to make DD-WRT router's (configured like a repeater) devices be accessible on LAN? (i.e. integrate DHCP for both routers)

  - by Annonomus Penguin

  I have a D-Link DIR-600-A1 router running DD-WRT (using the 601's firmware: except for the model number, they are near identical). It has an Atheros chip, so there is no "repeater" option. You can bypass this by setting the main radio as a client to the main router, and adding a virtual radio configured as an AP. You can then set up the credentials for connecting to the main router and allowing devices to connect to the repeater/router. I have a few devices on my network: Ethernet computers Server with Samba running WiFi devices connected to the main router I then wanted to add a repeater. I have a couple of other things on the repeater: WiFi Computer Other WiFi devices. Anyway, I wanted to connect my WiFi computer to the share on my server via Samba. However, for some reason, my router treats the main router as WAN, not another device. I've tried disabling the SPI firewall: However, that doesn't work. I've tried pinging my WiFi computer from my server. However, I can ping my server from my WiFi computer. AFAIK, they are on the same subset, just using different IPs: the main one uses 192.168.0.x and the repeater uses 192.168.1.x (starting at 100 for some reason). It seems as I need to configure my router(s) to work together for DHCP. I noticed there was a "DHCP forwarder" option, but I have no idea what that would do. A quick note: for some reason (that's beyond me) my ISP disabled the capability to bridge a WiFi to ethernet connection with the router they provide (something about PPPoE or similar...). The service rep I talked to when I was having issues after I changed ISPs said that, but they couldn't explain exactly what they were "blocking." How can I get DD-WRT to not treat the client connection as WAN and the router to recognize the devices connected to the repeater?

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >