Search Results

Search found 7935 results on 318 pages for 'aka nice'.

Page 232/318 | < Previous Page | 228 229 230 231 232 233 234 235 236 237 238 239  | Next Page >

• Best way to attach 96 tb to workstation

  - by user994179

  I'm running a workstation with dual xeon 5690's (12 physical/24 logical cores), 192 gb of ram (ie, maxed-out), Windows 7 64bit, 5 slots for adapter cards, and 1 tb of internal storage, with 5 more internal bays available. I have an app that creates data files totaling about 88 tbs. These are written once every 14 months, and the rest of the time the app only needs to read them; and 95% of the reads are sequential reads of huge chunks of data. I have some control over how big the individual files are, but ideally they would be between 5 and 8 tbs. The app will be reading from only one drive at a time, and the nature of the data is such that if (when) a drive dies I can restore the data to a new disk from tape. While it would be nice to be able to use the fastest drive/controllers available, at this point size matters more than speed. After doing lots of reading, I am leaning toward buying a bunch of cheap 2tb drives and putting them into a bunch of cheap enclosures. All this stuff is going into my home office, so I need to avoid the raised floor/refrigerated approach. My questions: Is the cheap drive/enclosure solution the best one for this situation? Given the nature of the app and the way the data is used, does RAID make sense? If so, which one? For huge sequential reads, would Usb 3.0 and eSata be a wash performance-wise? For each slot available on the workstation, can I hook up an enclosure that can hold multiple drives? Or is it one controller per drive? If I can have multiple drives on one controller, am I essentially splitting the bandwidth (throughput)? For example, if I have a 12 bay enclosure, is the throughput of the controller reduced by a factor of 12? Are there any Windows 7 volume/drive/capacity limits I should be aware of? Thanks

  Read the article

• Broken filesystem on Windows XP / 7 virtual machine

  - by Pekka

  I created a virtual machine with Windows XP as the guest system in Microsoft's Virtual PC that ships along with Windows 7. I then installed Virtualbox and began running the MS machine in it. It worked fine. Then, I accidentally started the machine in Microsoft's Virtual PC again. The screen stayed blank, so after a while, realizing my mistake, I closed the Machine. Since then, the VM won't start any more, claiming massive file system problems. Starting Windows in normal mode results in a SOMETHING_FILESYSTEM blue screen; I can start in protected mode and run a checkdisk. That will fix something on every run, but every time I restart, it will start again. I tried re-booting the VM with the Windows CD and doing a repair install. I didn't watch whether that worked out, but I'm caught in the reset / check disk / reset cycle again. Is there anything VM specific that can still be done? On a physical machine, I would say reformat. Is there any way to get hold of the data on the virtual machine through either Virtual PC or Virtualbox? It was an experimental machine, but I had started entering some data on it that would be nice to recover.

  Read the article

• Free/opensource application for charting stock prices?

  - by Homunculus Reticulli

  I am looking for a free or FOSS software application for SIMPLY charting stock prices. I am not interested in any of the other nonsense typically bundled with such packages (technical analysis, back testing, tracking etc, etc). All I want to do is the following: Import file from CSV and plot on the chart Ability to scroll the chart left/right (zoom feature would be nice to) Ability to draw straight line (between 2 points) on the plot Ability to plot the graph for different resolutions (for e.g weekly, monthly - or some other custom resolution that I want) print the displayed graph (I can always use screen capture if printing is too much to ask) Thats all I want to do. I am not interested in anything else. I would have thought I could have found something by now. I would have written my own tool (I still will do that at a later stage), but I am a bit short of time at the moment, so I just want something that will do all of the above. Can anyone recommend a package. Last but not the least, I am running on Linux (and would prefer to do so - BUT if I have to, I can run on ahem - you know, Windows)

  Read the article

• Apple / Mac OS X - Is there a Package Manager like Linux

  - by Walter White

  I am a Linux/UNIX user and love the package management that comes with it. For the most part, I like Ubuntu, but just like anything else, it is the minor things that you live with daily that would be nice if they just worked. My main issue is my wacom tablet while it works, every time there is an OS update, I have to rebuild the wacom driver. The other slightly annoying issue is, my ATI video card is not fully supported. When I use the HDMI out, the sound doesn't go through it, and the screen is not entirely used. I would happily get an Apple if it had a similar package management system like Ubuntu, Gentoo, or other Linux distribution. This takes the work out of getting the latest enhancements or fixes. It also takes all the guess work out about what you need to get something to work. I just want to use my computer, not administer it. Aside from Apple applications, if I wanted to install the GIMP on an apple, would it go and fetch ufraw if I wanted support for that and whatever other dependencies GIMP has? If I want Netbeans installed, will it go and get a JDK and maven if I want that? If not, is there something in the works? I know I don't update my applications that frequently, but that is mainly because I'm not aware of the updates. The updates all happen in the background. Walter

  Read the article

• How can I do a large file upload using Sinatra, haml, nginx, and passenger?

  - by mmr

  Hi all, I need to be able to allow a user to upload 30-60 mb files at a time. Right now, I'm solving the problem with a simple form post: %form{:action=>"/Upload",:method=>"post",:enctype=>"multipart/form-data"} - @theModelHash.each do |key,value| %br %input{:type=>"checkbox", :name=>"#{key}", :value=>1, :checked=>value} =key %br %input{:type=>"file",:name=>"file"} %input{:type=>"submit",:value=>"Upload"} This form allows the user to select processing options contained in theModelHash and upload a file for processing. Problem is, this method both freezes the user's UI and also requires that the entire form be reposted when the user presses the 'back' button. I've looked at SWFUpload, but have no idea how to integrate that into my relatively simple app. There's a page here about integrating it with Rails, but I'm using Sinatra, and am new enough to this whole web programming thing that I don't know how to modify those files to work with what I need to do. Is there a how-to to add large file uploads to my form there? Something relatively simple that just adds in a progress bar and doesn't repost? I feel like I'm having to triple the size of my application just to make this feature play nice, and that's bothering me a bit.

  Read the article

• Libraries merged folder views

  - by Stigma

  So I pretty much love the Windows 7 Libraries feature, and saw one use for them that I thought would be perfect, but I can't seem to manage it. Basically, a merged view of different folder structures. Suppose I make a new generic library and add three locations to it: C:\Test\, D:\Test\ and D:\temp\Test\. Now, these may look somewhat okay as long as there are no duplicates in these folders. (It wants to group them based on the included directory, which one can work around by looking on google - I don't have the precise trick on hand I am afraid.) But when you get collisions and, say, two of those directories have a Sub directory in them, stuff becomes unusable (assuming Arrange by: Folder view). You'll have multiple folders listed named Sub, which is pretty useless when looking for data. I want folders to get 'merged', which ought to be possible somehow since it can create these merged views based on artist, album etc in other views. So all subdirectories that are double (and recursively checking for doubles inside those, etc) ought to be merged for as far the View is concerned. If files have a collision, I don't really care what happens - hide one, show both, filter out duplicates, whatever. (Although an option would be nice...) Anyhow, is there anyone who knows how to get such a 'merged folder structure' functionality for Libraries? It would be really useful for me.

  Read the article

• Burn .srt subtitles to AVC encoded video (transcoding with hardsubs) [closed]

  - by Saxtus

  Possible Duplicate: How do I hard code a movie with subtitles? I am looking for a software (or combination of software) that will allow me to hard burn subtitles from an .srt file, that has italics and bold typefaces, to an H.264/AVC encoded video so it can played from a desktop player that can't display external subtitles correctly. Ideally it could use Directshow as input as DirectVobSub makes nice job showing the subtitles as they should (allowing me to globally adjust font and size). CUDA use, to speed up encoding, will be great but not necessary. Video source is also H.264/AVC encoded. Audio is AC-3 5.1 and should be retained too but I have no problem re-muxin it later as long as it keeps synced. Until now I've unsuccessfully tested: Avisynth 2.58 Unable to make Direcvobsub to launch through it TextSub() command renders subtitles with fixed font/size and doesn't decode tags Malformed audio TMPGEnc 4.0 XPress 4.7.4.299 Audio downmixed to 2.0 Importing of subtitles doesn't decode tags Badaboom 1.2.1.7 No importing of subtitles at all SUPER © 2010.build.37 "Directshow decode" has similar effect as Avisynth above Other modes doesn't appear to allow any subtitles in Thank you.

  Read the article

• ffmpeg: converting an avi to a reduced, shareable flv/mp4...

  - by meder

  I recently followed a guide and recompiled my ffmpeg so x264 is enabled. I used some generic settings to convert my 700 MB avi file to a mp4 file, the result was a 407MB mp4 file. The original avi file's settings: Codec: DX50 Resolution: 704x304 Frame rate: 23.976023 Stream 1 Codec: mpga Type: Audio Channels: 2 Sample rate: 48000 Hz Bitrate 179 kb/s Command I used: ffmpeg -i input.avi -acodec libfaac -ab 128k -ac 2 -vcodec libx264 -vpre hq -crf 22 -threads 0 output.mp4 The settings of the output file (output.mp4): Codec: avc1 Resolution: 704x304 Display resolution: 704x304 Frame rate: 11.988011 Stream 1 Codec: mp4a Type: Audio Channels: 2 Sample Rate: 48000 Hz Bits per sample: 16 Bitrate: 1536 kb/s The quality of the output mp4 is pretty nice, it seems as if it's pretty much the same as the original source. However, I'm trying to reduce the filesize and I'm not really sure whether I should go with an flv format or keep it mp4. The advantage the flv would have obviously is that it would be playable with a flash player ( I have come across some swf players which take a flash parameter to play an flv file ).. but maybe I could use the video element, as I'm only going to be displaying this video privately so I don't have to worry about supporting legacy browsers such as IE. Can someone recommend some settings to specify in order for the filesize to be around ~100-150MB or so? I don't mind a reduction in quality, nor do I mind resizing it - I was going to do it initially but I wasn't sure what the guidelines were ( if any ) for dealing with resolution.. since this video's is 704x304 would it still be ok if I forced it into one that isn't perfectly fit for the aspect ratio? I have no clue about that part. I realize that I could have probably specified 28 instead of 22 for the CRF, I'm not sure if I should do that as opposed to maybe specifying smaller resolution, which might make it smaller as well?

  Read the article

• iptables, blocking large numbers of IP Addresses

  - by Twirrim

  I'm looking to block IP addresses in a relatively automated fashion if they look to be 'screen scraping' content from websites that we host. In the past this was achieved by some ingenious perl scripts and OpenBSD's pf. pf is great in that you can provide it nice tables of IP addresses and it will efficiently handle blocking based on them. However for various reasons (before my time) they made the decision to switch to CentOS. iptables doesn't natively provide the ability to block large numbers of addresses (I'm told it wasn't unusual to be blocking 5000+), and I'm a bit cautious over adding that many rules into an iptable. ipt_recent would be awesome for doing this, plus it provides a lot of flexibility for just severely slowing down access, but there is a bug in the CentOS kernel that is stopping me from using it (reported, but awaiting fix). Using ipset would entail compiling a more up-to-date version of iptables than comes with CentOS which whilst I'm perfectly capable of doing it, I'd rather not do from a patching, security and consistency perspective. Other than those two it looks like nfblock is a reasonable alternative. Is anyone aware of other ways of achieving this? Are my concerns about several thousand IP addresses in iptables as individual rules unfounded?

  Read the article

• Probability of Blade Chassis Failure

  - by ChrisZZ

  In my organisation we are thinking about buying blade servers - instead of rack servers. Of course technology vendors also make them sound very nice. A concern, that I read very often in different forums, is, that there is a theoretical possibility of the server chassis going down - which would in consequence take all the blades down. That is due to shared infrastructure. My reaction on this probability would be to have redundancy and by two chassis instead of one (very costly of course). Some people (including e.g. HP Vendors) try to convince us, that the chassis is very very unlikely to fail, due to many redundancies (redundant power supply, etc.). Another concern on my side is, that if something goes down, spare parts might be required - which is difficult in our location (Ethiopia). So I would ask to experienced administrators, that have managed blade server: What is your experience? Do they go down as a whole - and what is the sensible shared infrastructure, that might fail? That question could be extended to shared storage. Again I would say, that we need two storage units instead of only one - and again the vendors say, that this things are so rock solid, that no failure is expected. Well - I can hardly believe, that such a critical infrastructure can be very reliable without redundancy - but maybe you can tell me, whether you have successfull blade-based projects, that work without redundancy in its core parts (chassis, storage...) At the moment, we look at HP - as IBM looks much to expensive... thanks a lot best regards Christian

  Read the article

• Optical Audio out stuck on on a MacBook

  - by Clinton Blackmore

  Apple have made an interesting headphone port for the MacBook (and some other Intel Mac models). It works like a standard jack: nothing plugged in - audio comes out of built-in speakers headphones/external speakers plugged in - plays through headphones/external speakers but you can also use a special adapter (which trips a tiny microswitch) to get an optical audio out signal (which you can presumably plug into a nice surround-sound system). This is all well and good except when, like auto-tracking, it doesn't work, and you are left with nothing to adjust. Users report that they get no sound when they have nothing plugged in and that a red light emanates from the headphone port. If you go to System Preferences - Sound - Output, it will say (IIRC) "Optical Out" instead of "Internal Speakers". The only solution I'm aware of is to try to reset the switch by inserting and removing a set of headphones or a toothpick, perhaps wiggling it inside of the port, and hoping that you luck out and get it. Are there other ways to fix this problem? Does anyone know where the microswitch is or have a good technique to reset it?

  Read the article

• Web-based SVG or JavaScript Org Chart or Tree Graph Plotting Visualization API

  - by asoltys

  Hi, I'm looking to build an interactive web-based org chart for a large organization. I somewhat like the interface at ancestry.com where you can hover over people and pan/zoom around and click on different nodes to make them the root. Ideally, I'd like it if people could belong to multiple organizational entities like committees, working groups, etc. In other words the API should support graphs in general, not just trees. I'd like to be able to visually explode each organizational substructure into substituents by clicking on it, with a nice animation of the employees ballooning or spilling out so you can really interactively drill down through the organization. I found http://code.google.com/apis/visualization/documentation/gallery/orgchart.html but it looks a bit rudimentary. I know there are desktop tools like OrgPlus and Visio that can build static charts but I'm really looking for a free, web-based API with open standards-based output like SVG or HTML5 Canvas elements rather than Flash or some proprietary output. Something I can embed into a custom web application and style myself. Something interactive.

  Read the article

• Unable to remove Read-Only attribute from folder in Windows XP

  - by elcuco

  I have this directory which I cannot remove the read only attribute from. The computer is running XP SP2 (or SP3, not sure) and the directory sits in a NTFS file system. Looking into the web I found this: http://support.microsoft.com/kb/256614 which tells that if the directory is "customized" it's treated as a system folder and thus "read only". I don't think this is a scenario in my case, but anyway it's not helping, their recommendation is more or less: attr -r -s /d /s d:\data and this is not working for me. Any other ideas? More info: The directory is served to an HTTP server (wamp) and the directory is an SVN check out. What happens is that the web server cannot write files into the directory (imagechace from drupal is you are really interested). Edit 2: The original post claimed that the directory sits on a VFAT FS, however I booted Fedora 11 from livecd and the partition is marked as NTFS. Edit 3: I left the company which I worked on, on which this situation happened... so I cannot fully close this question. But things get even worse: I tested the "attr -r" answer I put, it did not work for me, and now the developer said that it worked for her. A nice WTF moment. Probably a reboot helped... Sorry for loosing details. If anyone has the same problem, and one of the answers helps him - please comment.

  Read the article

• Home network with two isolated separate subnets, running on cablemodem/router and WRT-router.

  - by Johan Allgoth

  I have a new connection with a nice new router/cable-modem. I'd like to setup it up optimally and needs some pointers. I am a complete n00b when it comes to routing. I want to end up with two separate subnets, 10.1.2.0/24 and 192.168.1.0/24 each available on their own wireless channel/SSID. Both firewalled. I want my wired computers on the gigabit switch, optimally with public ips. I want to be able to reach 192.168.1.0/24 from 10.1.2.0/24, but not vice versa. Everyone should have internet access. Hardware and capabilities: Netgear CG3100. Handles cable connection. Gigabit switch. 802.11n. Can do DHCP, firewall, NAT etc. Can choose subnet. Can turn of NAT and if so hand out up to 4 public ips. Somewhat challenged when it comes to configuration. WRT-router. Runs DD/Open-WRT very stable. 100 Mbit switch. 802.11.g Can do DHCP, firewall, NAT etc. Can choose subnet. Highly configurable. I hope to be able to keep 10.1.2.0/24 on the CG3100, for speed reasons and 192.168.0.0/24 on the WRT-router for quota and user control reasons. On my 10.1.2.0/24 network I plan on running servers for various services. Should I turn of NAT on the WRT-router? Or on the cable modem? Activate what in that case? Is double NAT always f-ed up?

  Read the article

• Interactive console based CSV editor

  - by Penguin Nurse

  Although spreadsheet applications for editing CSV files on the console used to be one of the earliest killer applications for personal computers, only few of them and even less documentation about them is still actively maintained. After having done extensive search on the web, manpages and source code, I ended up with the following three applications that all have fundamental drawbacks: sc: abbrev. for spreadsheet calculator; nice tool with vi keybings, but it does not put strings containing the delimiter into quotas when exporting to delimiter separated format and can't import csv files correctly, i.e. all numbers are interpreted as strings GNU oleo: doesn't seem to be actively maintained any longer since 2001 and there are therefore no packages for major linux distributions teapot: offers packages for various operating systems, but uses for example counter-intuitive naming for cells (numbers for row and column, i.e. 11 seems to be intended to be row 1, column 1) and superfluous code for FLTK GUI Various Emacs modes also do not quote strings containing the delimiter well or are require much more typing for entering the scaffold of a table. Therefore I would be very grateful for overcoming one of theses drawbacks or any hints towards another console based CSV editor. It actually needn't do any calculations just editing cells or column- and rowise.

  Read the article

• Problems with Windows 7 restore

  - by Chris Lively

  My WD raptor 150 failed with a nice clicking noise. So, I picked up a velociraptor 300 and popped it in. I had windows set to do a full system backup nightly, so I figured the recovery ought to go easily. Well, it isn't. It is currently stuck on a screen that says: "Windows is restoring your computer from the system image. This might take from a few minutes to a few hours" Below that is a rather large progress meter with maybe the first block filled in. Below that is a message that says "Restoring disk (C:)..." It's been that way for over an hour. The first time around, I gave up after 2 hours. I then booted into the system recovery options and went to a command prompt and ran a chkdsk on the new drive. It showed several file inconsistencies and not much else. I ran a chkdsk /f on it and tried again... Which is where I'm at now. I can't see that the restore process should take this long before. Any ideas? UPDATE After 10 hours, it's still on "Restoring disk (C:)" and the progress meter is at roughly 5%. I'm guessing at the 5% as there isn't an actual number or anything else that I can look at showing what it's actually doing. The backup contains roughly 120GB of data. How slow is windows restore?

  Read the article

• How to read cell data in excel and output to command prompt

  - by Max Ollerenshaw

  Hi All, I'm a sys admin and I am trying to learn how to use powershell... I have never done any type of scripting or coding before and I have been teaching myself online by learning from the technet script centre and online forums. What I am trying to accomplish is to open an excel spreadsheet get information from it (usernames and password) and then output it into the command prompt in powershell. When ever I try to do this I get an Exception calling "InvokeMember" anyway, here is the code I have so far: function Invoke([object]$m, [string]$method, $parameters) { $m.PSBase.GetType().InvokeMember( $method, [Reflection.BindingFlags]::InvokeMethod, $null, $m, $parameters,$ciUS ) } $ciUS = [System.Globalization.CultureInfo]'en-US' $objExcel = New-Object -comobject Excel.Application $objExcel.Visible = $False $objExcel.DisplayAlerts = $False $objWorkbook = Invoke $objExcel.Workbooks.Open "C:\PS\User Data.xls" Write-Host "Numer of worksheets: " $objWorkbook.Sheets.Count $objWorksheet = $objWorkbook.Worksheets.Item(1) Write-Host "Worksheet: " $objWorksheet.Name $Forename = $objWorksheet.Cells.Item(2,1).Text $Surname = $objWorksheet.Cells.Item(2,2).Text Write-Host "Forename: " $Forename Write-Host "Surname: " $Surname $objExcel.Quit() If (ps excel) { kill -name excel} I have read many different posts on forums and articles on how to try and get around the en-US problem but I cannot seem to get around it and hope that someone here can help! Here is the Exeption problem I mentioned: Exception calling "InvokeMember" with "6" argument(s): "Method 'System.Management.Automation.PSMethod.C:\PS\User Data.x ls' not found." At C:\PS\excel.ps1:3 char:33 + $m.PSBase.GetType().InvokeMember <<<< ( + CategoryInfo : NotSpecified: (:) [], MethodInvocationException + FullyQualifiedErrorId : DotNetMethodException Numer of worksheets: You cannot call a method on a null-valued expression. At C:\PS\excel.ps1:18 char:45 + $objWorksheet = $objWorkbook.Worksheets.Item <<<< (1) + CategoryInfo : InvalidOperation: (Item:String) [], RuntimeException + FullyQualifiedErrorId : InvokeMethodOnNull Worksheet: You cannot call a method on a null-valued expression. At C:\PS\excel.ps1:21 char:37 + $Forename = $objWorksheet.Cells.Item <<<< (2,1).Text + CategoryInfo : InvalidOperation: (Item:String) [], RuntimeException + FullyQualifiedErrorId : InvokeMethodOnNull You cannot call a method on a null-valued expression. At C:\PS\excel.ps1:22 char:36 + $Surname = $objWorksheet.Cells.Item <<<< (2,2).Text + CategoryInfo : InvalidOperation: (Item:String) [], RuntimeException + FullyQualifiedErrorId : InvokeMethodOnNull Forename: Surname: This is the first question I have ever asked, try to be nice! :)) Many Thanks Max

  Read the article

• RAID administration in Debian Lenny

  - by Siim K

  I've got an old box that I don't want to scrap yet because it's got a nice working 5-disk RAID assembly. I want to create 2 arrays: RAID 1 with 2 disks and RAID 5 with the other 3 disks. The RAID card is Intel SRCU31L. I can create the RAID 1 volume in the console that you access with Ctrl+C at startup. But it only allows for creation of one volume so I can't do anything with the 3 remaining disks. I installed Debian Lenny on the RAID 1 volume and it worked out nicely. What utilites could I now use to create/manage the RAID volumes in Debian Linux? I installed the raidutils package but get an error when trying to fetch a list: #raidutil -L controller or #raidutil -L physical # raidutil -L controller osdOpenEngine : 11/08/110-18:16:08 Fatal error, no active controller device files found. Engine connect failed: Open What could I try to get this thing working? Can you suggest any other tools? Command #lspci -vv gives me this about the controller: 00:06.1 I2O: Intel Corporation Integrated RAID (rev 02) (prog-if 01) Subsystem: Intel Corporation Device 0001 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Step ping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 26 Region 0: Memory at f9800000 (32-bit, prefetchable) [size=8M] [virtual] Expansion ROM at 30020000 [disabled] [size=64K] Capabilities: <access denied> Kernel driver in use: PCI_I2O Kernel modules: i2o_core

  Read the article

• Can I tell if crashplan has backed up a particular file in a particular state?

  - by Chris Cogdon

  I would like to be able to tell, programmatically, if CrashPlan has backed-up a particular file, including the current updates to that file. I.e., that the current contents of a file are backed up. It's relatively easy to tell when CrashPlan last backed up a file: its file name appears in /usr/local/crashplan/log/backup_files.log.0, and with some accuracy, I could compare the backup time with the last modification time to the file, but that method appears to be somewhat dubious. A couple of methods I could think of, but I don't know how: Compare the current file to CrashPlan's metadata about that file. This needs knowledge about the format of CrashPlan's "cache" files as well as the hashing system used. This might be achievable through the CLI, but the CLI is just a portal into the GUI, and I need something that's scriptable. Restore the file to a temporary directory, and compare it. Unfortunately, there is no CLI to do restores; the GUI is the only way. I'll describe what I'm trying to achieve. It would be nice to know how to do the above, even if there are alternative methods for the following: I'm using CrashPlan for continuous backups to my PostgreSQL database, using WAL archives. In the current configuration, the archive command copies the files to an archive directory, which is backed up by CrashPlan. Every so often I manually confirm (or just trust) a group of WALs are backed up, and remove them from the archive directory, and occasionally do a restore through the GUI to ensure I can retrieve current and "deleted" WALs. The xlog directory is backed-up, too, so I have a good chance of doing a near-full restore even if a particular xlog hasn't been archived by PostgreSQL yet. I'd like to be able to automate this process, which necessitates either confirming the backup status and recency, or automating a restore for comparison purposes. (As a bonus, if the method is trustworthy, I could turn the "archive_command" from "copy to archive directory" into "confirm CrashPlan has backed up the current version", and do away with the archive directory completely). (And, yes, I'm doing regular pg_dumpall's, in addition to the above.)

  Read the article

• Underbraces in Word math zones and dealing with stretchy parentheses

  - by Johannes Rössel

  Parentheses in Word usually stretch with whatever they're containing. This might be un-noticeable for things like but for stuff like it's definitely nice, especially compared to the fact that naïve LaTeX users often produce uglinesses such as There is a problem, however, when using under-/overbraces in math and putting parentheses around the complete term it becomes ugly. For simple things like shown here this can be solved by not letting the parentheses stretch which looks almost right. However, for more complex things it's certainly not an option: Both variants look horrible. So is there a way of letting the parentheses only stretch around the actual term parts, not including the under-/overbraces? Those are frequently used for annotations of individual pieces, so simply not using them is a bad idea too. In LaTeX you can get away with guesswork and using explicit sizes for the parentheses instead of relying on \left and \right but I haven't found a comparable option in Word yet. Since the underbrace is (tree-wise) a sibling of the term in parentheses it probably simply has to stretch and there probably can't be an algorithm that determines when to stretch or when not, considering that \above and \below are used for annotations as well but also for other things where perentheses have to stretch. Also, since the parenthesized expression is opaque from the outside one has to put the underbrace inside. From a markup point of view, at least. One can probably draw the rest around but that falls apart when styles change and wouldn't be a good idea either.

  Read the article

• My Computer hangs for a few minutes just after startup, and then is fine.

  - by EvilChookie

  So I just built myself a reasonably beefy computer, and I installed Windows 7 on it. However, I start the machine up each morning and within a few minutes, the computer will semi hang. That is the mouse is responsive, and most of the time I can open task manager, or a new tab in Chrome. Occasionally windows will be labelled as 'Not responding'. Then, the machine will get over it's problem, and will be nice and quick until I turn it off. Here's my specs: CPU: AMD Phenom-II X4 955 Black (Quad Core, 3.2ghz) RAM: 4GB of DDR3 1300 MOBO: ASUS M4A785T-M (Latest BIOS) HARD DRIVES: 2x1TB Western Digital Caviar Blacks in RAID-0. OS: Windows 7 Ultimate x64. GPU: ASUS GT240 1GB. I believe this issue relates to the RAID array, as I didn't have the lockup problem before I created the array. I purchased a second drive and reformatted after creating a RAID array, since the single drive was a little on the pokey side (compared to the rest of the computer). What I have tried: Updated Raid Drivers Malware checks Windows Updates Unecessary Services CPU and Disk activity appears to be low (via Resource Monitor) No strange errors in the error log. Any thoughts?

  Read the article

• Choosing the right e-mail client

  - by CFP

  Hi all, I'm currently using Outlook 2007 (under windows 7), but I much prefer free software (open source being the best of course), so I thought I'd ask for expert advice here. I thought it might be easier if I included a small "wanted list": I receive about 15 to 30 e-mails every day, but I have large archives (10'000 emails), which I frequently need to access. I usually open and close my mail program many times, so I'd like it to start pretty fast I cannot use an online mailbox, because I have too many email addresses (about 5: 1 for work, 1 for home, 1 semi-private, 1 for specific emails, and 1 for newletters By order of importance, the things I'd like my mail client to be able to: Efficiently categorize e-mails. Until now, I've mostly been using Outlook folders, because filtering by tags was not easy, but I'd rather one large list of mails, neatly tagged so I can easily filter. I'd love being able to select mails by tags (eg in a click or too (could be a tab) show all mails tagged with "software") Create "tagging rules", such as "if the mail was sent to this address, add this tag", or "if the body contains ..., add that tag" Sync contacts with Gmail, handle tasks (syncing with toodledo would be awesome), possibly provide a calendar Create e-mail templates, signatures... Other ideas: A timeline, scripting support, being able to import MS Outlook emails, provide a nice backup format... Thanks for sharing ideas and suggestions!

  Read the article

• How to get automatic upgrades to work on Ubuntu Server?

  - by J. Pablo Fernández

  I followed the documentation for enabling automatic upgrades in Ubuntu servers, but it's not really updating anything at all. My /etc/apt/apt.conf.d/50unattended-upgrades looks almost like the default. // Automatically upgrade packages from these (origin, archive) pairs Unattended-Upgrade::Allowed-Origins { "Ubuntu karmic-security"; "Ubuntu karmic-updates"; }; // List of packages to not update Unattended-Upgrade::Package-Blacklist { // "vim"; // "libc6"; // "libc6-dev"; // "libc6-i686"; }; // Send email to this address for problems or packages upgrades // If empty or unset then no email is sent, make sure that you // have a working mail setup on your system. The package 'mailx' // must be installed or anything that provides /usr/bin/mail. Unattended-Upgrade::Mail "[email protected]"; // Automatically reboot *WITHOUT CONFIRMATION* if a // the file /var/run/reboot-required is found after the upgrade //Unattended-Upgrade::Automatic-Reboot "false"; The directory /var/log/unattended-upgrades/ is empty. Running /etc/init.d/unattended-upgrades start is not very nice: root@mozart:~# /etc/init.d/unattended-upgrades start Checking for running unattended-upgrades: root@mozart:~# Something seems to be broken, but I'm not sure why. I have pending updates and they are not being applied: root@mozart:~# aptitude safe-upgrade Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done The following packages will be upgraded: linux-libc-dev 1 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 0B/743kB of archives. After unpacking 4096B will be used. Do you want to continue? [Y/n/?] In all the servers I have, unattended upgrades seems to have been disabled: root@mozart:~# apt-config shell UnattendedUpgradeInterval APT::Periodic::Unattended-Upgrade root@mozart:~# Any ideas what am I missing?

  Read the article

• On what should i not be pennywise buying a machine for SqlServer 2008?

  - by Michel

  Hi, i'm going to do a project for a client and i'll be hosting the database server myself. Normally it would be on my dev machine, but there will also be data pushed into it during developing and testing, so i would like to setup a dedicated test sql server. But, as you might guess, i can't afford to go to Dell and buy one mega 16 core 16 GIG 10 TB raid 5 machine (wow, that sounds cool) So i have to save the money somewhere... the hardware only has to live for a year (longer is nice of course), and the sql server won't be hit too hard: i guess the average server will only see it as a cough once in a while. But i do want the machine to be a bit performant: if it does get some data, it must be a bit responsive. So my question is were can i leave out the expensive parts: is 2 GB enough, or must i take 4GB, is an average processor enough or should it be a top of the bill? Is Sql server a large resource user or is a simple desktop pc good enough? It wil run on win2008 by the way.

  Read the article

• Virtual machines with failover setup

  - by kimmmo

  We have three servers and our plan is to run a number of virtual machines on them in such manner, that if one of the nodes blow up, we can either quickly or seamlessly get a spare running on another node. In addition to the normal networking, they're interconnected via dual 10Gbit NIC's, so networked raid/mirroring shouldn't be a problem. The guest VM's are mostly going to be running text mode linux, but of course it wouldn't hurt to be able to spin up a non-mission critical windows guest for running Visual Studio or checking IE compatibility of a web app. We've spent some time trying to get some magical cloud setup running using Stackops and Crowbar but it started to look like they were offering way too much and were too complicated for our needs. The next candidate, I think, is Ubuntu 11.04 server + KVM + Ganeti + Drbd, unless you can come up with a suggestion for a better solution that we have missed. Requirements: Installation should be simple or at least understandable without being in the dev team A browser interface for creating and managing VM's is a nice bonus Single node's hardware failure should cause minimal downtime for VM's that were running on that node Adding more nodes should be possible without shutting down the VM's.

  Read the article

< Previous Page | 228 229 230 231 232 233 234 235 236 237 238 239  | Next Page >