Search Results

Search found 9051 results on 363 pages for 'camel space'.

Page 232/363 | < Previous Page | 228 229 230 231 232 233 234 235 236 237 238 239  | Next Page >

• QLogic QLE8152 won't link up with a fiber loop

  - by Mike Pennington

  I have a Dell R710 running Debian Linux 6.0 (Squeeze). I installed a QLogic QLE8152 CNA in the PCI-E riser today and I have been trying to get the CNA's ethernet layer to come up after I put a fiber loop on it; I also scoped it with a light meter, and the SFP+ transceiver is getting the correct amount of light. The whole time I have been working on this problem, the lights on the CNA are blinking green at a rate of about 1 flash every 3 seconds. When I plug the fiber into a Juniper EX4500 10GE in a rack next to it, the Juniper's link stays down as well. I have to confess that this is my first wrangling with a CNA, so perhaps I'm doing something fundamentally wrong, but here is what I have found so far... First the basics... [mpenning@Finger ~]$ uname -a Linux Finger 2.6.32-5-amd64 #1 SMP Mon Oct 3 03:59:20 UTC 2011 x86_64 GNU/Linux [mpenning@Finger ~]$ cat /etc/issue Debian GNU/Linux 6.0 \n \l [mpenning@Finger ~]$ lspci -v shows that the card is properly installed (physically) 04:00.0 Ethernet controller: QLogic Corp. 10GbE Converged Network Adapter (TCP/IP Networking) (rev 02) Subsystem: QLogic Corp. Device 017e Flags: bus master, fast devsel, latency 0, IRQ 34 I/O ports at e000 [size=256] Memory at df8f0000 (64-bit, non-prefetchable) [size=16K] Memory at df900000 (64-bit, non-prefetchable) [size=1M] Expansion ROM at df800000 [disabled] [size=256K] Capabilities: [44] Power Management version 3 Capabilities: [4c] Express Endpoint, MSI 00 Capabilities: [88] MSI: Enable- Count=1/32 Maskable- 64bit+ Capabilities: [98] Vital Product Data Capabilities: [a0] MSI-X: Enable+ Count=8 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [138] Device Serial Number 00-c0-dd-ff-fe-1c-53-b4 Capabilities: [144] Power Budgeting <?> Kernel driver in use: qlge The output from ethtool shows that eth4 is the QLE8152... [mpenning@Finger ~]$ sudo ethtool eth4 Settings for eth4: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: on Current message level: 0x000060f7 (24823) Link detected: no [mpenning@Finger ~]$ sudo ethtool -i eth4 driver: qlge version: v1.00.00-b3 firmware-version: v1.35.11 bus-info: 0000:04:00.0 [mpenning@Finger ~]$ Finally, I tried modprobe -r qlge; modprobe -r qla2xxx and then modprobe qla2xxx; modprobe qlge to kick the system again... I don't see a smoking gun in /var/log/messages... Nov 17 19:46:21 finger kernel: [ 6212.298275] qlge 0000:04:00.1: PCI INT B disabled Nov 17 19:46:22 finger kernel: [ 6213.779974] qlge 0000:04:00.0: PCI INT A disabled Nov 17 19:46:33 finger kernel: [ 6224.554074] qla2xxx 0000:04:00.3: PCI INT D disabled Nov 17 19:46:33 finger kernel: [ 6224.555322] qla2xxx 0000:04:00.2: PCI INT C disabled Nov 17 19:46:54 finger kernel: [ 6245.625854] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:54 finger kernel: [ 6245.625888] qla2xxx 0000:04:00.2: PCI INT C -> GSI 35 (level, low) -> IRQ 35 Nov 17 19:46:54 finger kernel: [ 6245.626837] qla2xxx 0000:04:00.2: MSI-X vector count: 7 Nov 17 19:46:54 finger kernel: [ 6245.626841] qla2xxx 0000:04:00.2: Found an ISP8001, irq 35, iobase 0xffffc90012664000 Nov 17 19:46:54 finger kernel: [ 6245.627113] qla2xxx 0000:04:00.2: Configuring PCI space... Nov 17 19:46:54 finger kernel: [ 6245.639429] qla2xxx 0000:04:00.2: Configure NVRAM parameters... Nov 17 19:46:54 finger kernel: [ 6245.642597] qla2xxx 0000:04:00.2: Verifying loaded RISC code... Nov 17 19:46:54 finger kernel: [ 6245.642708] qla2xxx 0000:04:00.2: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.273340] qla2xxx 0000:04:00.2: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.273401] qla2xxx 0000:04:00.2: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.273486] qla2xxx 0000:04:00.2: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.273856] scsi9 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.274631] qla2xxx 0000:04:00.2: Nov 17 19:46:55 finger kernel: [ 6246.274633] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.274634] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.274636] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.2 hdma+, host#=9, fw=5.01.04 (8d4) Nov 17 19:46:55 finger kernel: [ 6246.274666] qla2xxx 0000:04:00.3: PCI INT D -> GSI 37 (level, low) -> IRQ 37 Nov 17 19:46:55 finger kernel: [ 6246.274748] qla2xxx 0000:04:00.3: MSI-X vector count: 7 Nov 17 19:46:55 finger kernel: [ 6246.274751] qla2xxx 0000:04:00.3: Found an ISP8001, irq 37, iobase 0xffffc900125c4000 Nov 17 19:46:55 finger kernel: [ 6246.275098] qla2xxx 0000:04:00.3: Configuring PCI space... Nov 17 19:46:55 finger kernel: [ 6246.287329] qla2xxx 0000:04:00.3: Configure NVRAM parameters... Nov 17 19:46:55 finger kernel: [ 6246.290624] qla2xxx 0000:04:00.3: Verifying loaded RISC code... Nov 17 19:46:55 finger kernel: [ 6246.290736] qla2xxx 0000:04:00.3: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.920204] qla2xxx 0000:04:00.3: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.920264] qla2xxx 0000:04:00.3: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.920345] qla2xxx 0000:04:00.3: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.920749] scsi10 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.921715] qla2xxx 0000:04:00.3: Nov 17 19:46:55 finger kernel: [ 6246.921716] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.921717] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.921719] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.3 hdma+, host#=10, fw=5.01.04 (8d4) Nov 17 19:46:58 finger kernel: [ 6249.519911] qlge 0000:04:00.0: PCI INT A -> GSI 34 (level, low) -> IRQ 34 Nov 17 19:46:58 finger kernel: [ 6249.533970] qlge 0000:04:00.0: QLogic 10 Gigabit PCI-E Ethernet Driver Nov 17 19:46:58 finger kernel: [ 6249.533975] qlge 0000:04:00.0: Driver name: qlge, Version: v1.00.00-b3. Nov 17 19:46:58 finger kernel: [ 6249.534856] qlge 0000:04:00.0: ql_display_dev_info: Function #0, Port 0, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.534860] qlge 0000:04:00.0: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b4 Nov 17 19:46:58 finger kernel: [ 6249.534888] qlge 0000:04:00.1: PCI INT B -> GSI 44 (level, low) -> IRQ 44 Nov 17 19:46:58 finger kernel: [ 6249.549109] qlge 0000:04:00.1: ql_display_dev_info: Function #1, Port 1, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.549112] qlge 0000:04:00.1: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b6 Any assistance getting a link up on this is greatly appreciated...

  Read the article

• WPF Orthographic Camera. Region of view

  - by Evgeny

  Hello. I added Orthographic Camera to my project. I want to show my chart on screen proportional. For example height is 4 and width 4 (region from -2 to 2). I set width to 4 and it perfectly fit my square in widht. but i have problem with height. The chart top and bottom is always out of screen space. Why this happens and how to set to camera view the same width and height ? Camera position: 0,0,5 Viewport have size: 571.5x497 On image we can see on vertical axis points from 2 to -2 but on vertical much more. How to make them same? Image: http://i076.radikal.ru/1003/96/273c74ed9add.png Sorry for my English.

  Read the article

• postgres - remove whitespace from field?

  - by n00b0101

  I imported a bunch of data using pgloader, and am now seeing that there's a bunch of whitespace (both spaces and tabs) inside of the fields. Is there a way to quickly update the fields to remove it from the beginning, the end, and the middle? I know there's TRIM, but that won't work for me... As an added problem... I only want to remove double spaces and replace it with a single space, but there might be 5 or 6 spaces in a row, and I'd prefer not to have to rerun a replace query until they're all ok? I was looking at regex_replace, but, I'm not sure how to make certain that it removes it from the middle of a string as well...

  Read the article

• How to show button ‘Done’ on number pad on iPhone OS 4?

  - by Will Harris

  I'd like to add a Done button to the iPhone number pad keyboard. There's even a handy space at the bottom left for just such a button. Previously, I was using a similar trick to those described in Question 584538 and Luzian Scherrer's excellent blog post, but that stopped working in iOS 4. I can do it by creating a custom inputView, but I'd prefer to extend Apple's keyboard instead of writing my own. Is there a new way to add a view to the standard keyboard? Has someone published an OSS inputView for this? Is there another way?

  Read the article

• flex combobox backspace or delete key does not delete highlighted text

  - by crazy horse

  Context: I am implementing a flex auto-suggest combobox - as the user types in each character: Consider the string 'Stackoverflow' and user input = 'st' 1) the data provider is filtered to show all items starting with 'st' 2) text is set to auto-suggest string such that the un-typed part is highlighted. So for instance, the combobox text may contain st'ackoverflow', where 'ackoverflow' is highlighted using setSelectedIndex() Issue: When I hit back-space or delete, and check the 'this.text' value, I expect that the last un-highlighted character ('t' in the above case) gets deleted and the data provider is filtered to show all items starting with 's'. However the text property contains 'st', as before Question: what am I missing? What else can I try out?

  Read the article

• Markdown for .NET/C#?

  - by jiewmeng

  is there a way i can have markdown in .NET/C# application? i wonder shld i store the data in HTML or markdown text? if i store the data in HTML, when the user edits, they will see HTML, but if i store in Markdown, everytime i display, i got to convert to HTML(slow?) or store the HTML in another column, will it waste too much space? i understand markdown.net maybe used for this site. isit true? but heard its not updated since 2004/5?

  Read the article

• Win7 Bluescreen: IRQ_NOT_LESS_OR_EQUAL | athrxusb.sys

  - by wretrOvian

  Hi I'd left my system on last night, and found the bluescreen in the morning. This has been happening occasionally, over the past few days. Details: ================================================== Dump File : 022710-18236-01.dmp Crash Time : 2/27/2010 8:46:44 AM Bug Check String : DRIVER_IRQL_NOT_LESS_OR_EQUAL Bug Check Code : 0x000000d1 Parameter 1 : 00000000`00001001 Parameter 2 : 00000000`00000002 Parameter 3 : 00000000`00000000 Parameter 4 : fffff880`06b5c0e1 Caused By Driver : athrxusb.sys Caused By Address : athrxusb.sys+760e1 File Description : Product Name : Company : File Version : Processor : x64 Computer Name : Full Path : C:\Windows\minidump\022710-18236-01.dmp Processors Count : 2 Major Version : 15 Minor Version : 7600 ================================================== HiJackThis ("[...]" indicates removed text; full log posted to pastebin): Logfile of Trend Micro HijackThis v2.0.2 Scan saved at 8:49:15 AM, on 2/27/2010 Platform: Unknown Windows (WinNT 6.01.3504) MSIE: Internet Explorer v8.00 (8.00.7600.16385) Boot mode: Normal Running processes: C:\Windows\DAODx.exe C:\Program Files (x86)\ASUS\EPU\EPU.exe C:\Program Files\ASUS\TurboV\TurboV.exe C:\Program Files (x86)\PowerISO\PWRISOVM.EXE C:\Program Files (x86)\OpenOffice.org 3\program\soffice.exe C:\Program Files (x86)\OpenOffice.org 3\program\soffice.bin D:\Downloads\HijackThis.exe C:\Program Files (x86)\uTorrent\uTorrent.exe R1 - HKCU\Software\Microsoft\Internet Explorer\[...] [...] O2 - BHO: Java(tm) Plug-In 2 SSV Helper - {DBC80044-A445-435b-BC74-9C25C1C588A9} - C:\Program Files (x86)\Java\jre6\bin\jp2ssv.dll O4 - HKLM\..\Run: [HDAudDeck] C:\Program Files (x86)\VIA\VIAudioi\VDeck\VDeck.exe -r O4 - HKLM\..\Run: [StartCCC] "C:\Program Files (x86)\ATI Technologies\ATI.ACE\Core-Static\CLIStart.exe" MSRun O4 - HKLM\..\Run: [TurboV] "C:\Program Files\ASUS\TurboV\TurboV.exe" O4 - HKLM\..\Run: [PWRISOVM.EXE] C:\Program Files (x86)\PowerISO\PWRISOVM.EXE O4 - HKLM\..\Run: [googletalk] C:\Program Files (x86)\Google\Google Talk\googletalk.exe /autostart O4 - HKLM\..\Run: [AdobeCS4ServiceManager] "C:\Program Files (x86)\Common Files\Adobe\CS4ServiceManager\CS4ServiceManager.exe" -launchedbylogin O4 - HKCU\..\Run: [uTorrent] "C:\Program Files (x86)\uTorrent\uTorrent.exe" O4 - HKUS\S-1-5-19\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-19\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-20\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'NETWORK SERVICE') O4 - HKUS\S-1-5-20\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'NETWORK SERVICE') O4 - Startup: OpenOffice.org 3.1.lnk = C:\Program Files (x86)\OpenOffice.org 3\program\quickstart.exe O13 - Gopher Prefix: O23 - Service: @%SystemRoot%\system32\Alg.exe,-112 (ALG) - Unknown owner - C:\Windows\System32\alg.exe (file missing) O23 - Service: AMD External Events Utility - Unknown owner - C:\Windows\system32\atiesrxx.exe (file missing) O23 - Service: ASUS System Control Service (AsSysCtrlService) - Unknown owner - C:\Program Files (x86)\ASUS\AsSysCtrlService\1.00.02\AsSysCtrlService.exe O23 - Service: DeviceVM Meta Data Export Service (DvmMDES) - DeviceVM - C:\ASUS.SYS\config\DVMExportService.exe O23 - Service: @%SystemRoot%\system32\efssvc.dll,-100 (EFS) - Unknown owner - C:\Windows\System32\lsass.exe (file missing) O23 - Service: ESET HTTP Server (EhttpSrv) - ESET - C:\Program Files\ESET\ESET NOD32 Antivirus\EHttpSrv.exe O23 - Service: ESET Service (ekrn) - ESET - C:\Program Files\ESET\ESET NOD32 Antivirus\x86\ekrn.exe O23 - Service: @%systemroot%\system32\fxsresm.dll,-118 (Fax) - Unknown owner - C:\Windows\system32\fxssvc.exe (file missing) O23 - Service: FLEXnet Licensing Service - Acresso Software Inc. - C:\Program Files (x86)\Common Files\Macrovision Shared\FLEXnet Publisher\FNPLicensingService.exe O23 - Service: FLEXnet Licensing Service 64 - Acresso Software Inc. - C:\Program Files\Common Files\Macrovision Shared\FLEXnet Publisher\FNPLicensingService64.exe O23 - Service: InstallDriver Table Manager (IDriverT) - Macrovision Corporation - C:\Program Files (x86)\Common Files\InstallShield\Driver\11\Intel 32\IDriverT.exe O23 - Service: @keyiso.dll,-100 (KeyIso) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @comres.dll,-2797 (MSDTC) - Unknown owner - C:\Windows\System32\msdtc.exe (file missing) O23 - Service: @%SystemRoot%\System32\netlogon.dll,-102 (Netlogon) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @%systemroot%\system32\psbase.dll,-300 (ProtectedStorage) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: Protexis Licensing V2 (PSI_SVC_2) - Protexis Inc. - c:\Program Files (x86)\Common Files\Protexis\License Service\PsiService_2.exe O23 - Service: @%systemroot%\system32\Locator.exe,-2 (RpcLocator) - Unknown owner - C:\Windows\system32\locator.exe (file missing) O23 - Service: @%SystemRoot%\system32\samsrv.dll,-1 (SamSs) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @%SystemRoot%\system32\snmptrap.exe,-3 (SNMPTRAP) - Unknown owner - C:\Windows\System32\snmptrap.exe (file missing) O23 - Service: @%systemroot%\system32\spoolsv.exe,-1 (Spooler) - Unknown owner - C:\Windows\System32\spoolsv.exe (file missing) O23 - Service: @%SystemRoot%\system32\sppsvc.exe,-101 (sppsvc) - Unknown owner - C:\Windows\system32\sppsvc.exe (file missing) O23 - Service: Steam Client Service - Valve Corporation - C:\Program Files (x86)\Common Files\Steam\SteamService.exe O23 - Service: @%SystemRoot%\system32\ui0detect.exe,-101 (UI0Detect) - Unknown owner - C:\Windows\system32\UI0Detect.exe (file missing) O23 - Service: @%SystemRoot%\system32\vaultsvc.dll,-1003 (VaultSvc) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @%SystemRoot%\system32\vds.exe,-100 (vds) - Unknown owner - C:\Windows\System32\vds.exe (file missing) O23 - Service: @%systemroot%\system32\vssvc.exe,-102 (VSS) - Unknown owner - C:\Windows\system32\vssvc.exe (file missing) O23 - Service: @%systemroot%\system32\wbengine.exe,-104 (wbengine) - Unknown owner - C:\Windows\system32\wbengine.exe (file missing) O23 - Service: @%Systemroot%\system32\wbem\wmiapsrv.exe,-110 (wmiApSrv) - Unknown owner - C:\Windows\system32\wbem\WmiApSrv.exe (file missing) O23 - Service: @%PROGRAMFILES%\Windows Media Player\wmpnetwk.exe,-101 (WMPNetworkSvc) - Unknown owner - C:\Program Files (x86)\Windows Media Player\wmpnetwk.exe (file missing) -- End of file - 6800 bytes CPU-Z ("[...]" indicates removed text; see full log posted to pastebin): CPU-Z TXT Report ------------------------------------------------------------------------- Binaries ------------------------------------------------------------------------- CPU-Z version 1.53.1 Processors ------------------------------------------------------------------------- Number of processors 1 Number of threads 2 APICs ------------------------------------------------------------------------- Processor 0 -- Core 0 -- Thread 0 0 -- Core 1 -- Thread 0 1 Processors Information ------------------------------------------------------------------------- Processor 1 ID = 0 Number of cores 2 (max 2) Number of threads 2 (max 2) Name AMD Phenom II X2 550 Codename Callisto Specification AMD Phenom(tm) II X2 550 Processor Package Socket AM3 (938) CPUID F.4.2 Extended CPUID 10.4 Brand ID 29 Core Stepping RB-C2 Technology 45 nm Core Speed 3110.7 MHz Multiplier x FSB 15.5 x 200.7 MHz HT Link speed 2006.9 MHz Instructions sets MMX (+), 3DNow! (+), SSE, SSE2, SSE3, SSE4A, x86-64, AMD-V L1 Data cache 2 x 64 KBytes, 2-way set associative, 64-byte line size L1 Instruction cache 2 x 64 KBytes, 2-way set associative, 64-byte line size L2 cache 2 x 512 KBytes, 16-way set associative, 64-byte line size L3 cache 6 MBytes, 48-way set associative, 64-byte line size FID/VID Control yes Min FID 4.0x P-State FID 0xF - VID 0x10 P-State FID 0x8 - VID 0x18 P-State FID 0x3 - VID 0x20 P-State FID 0x100 - VID 0x2C Package Type 0x1 Model 50 String 1 0x7 String 2 0x6 Page 0x0 TDP Limit 79 Watts TDC Limit 66 Amps Attached device PCI device at bus 0, device 24, function 0 Attached device PCI device at bus 0, device 24, function 1 Attached device PCI device at bus 0, device 24, function 2 Attached device PCI device at bus 0, device 24, function 3 Attached device PCI device at bus 0, device 24, function 4 Thread dumps ------------------------------------------------------------------------- CPU Thread 0 APIC ID 0 Topology Processor ID 0, Core ID 0, Thread ID 0 Type 0200400Ah Max CPUID level 00000005h Max CPUID ext. level 8000001Bh Cache descriptor Level 1, I, 64 KB, 1 thread(s) Cache descriptor Level 1, D, 64 KB, 1 thread(s) Cache descriptor Level 2, U, 512 KB, 1 thread(s) Cache descriptor Level 3, U, 6 MB, 2 thread(s) CPUID 0x00000000 0x00000005 0x68747541 0x444D4163 0x69746E65 0x00000001 0x00100F42 0x00020800 0x00802009 0x178BFBFF 0x00000002 0x00000000 0x00000000 0x00000000 0x00000000 0x00000003 0x00000000 0x00000000 0x00000000 0x00000000 0x00000004 0x00000000 0x00000000 0x00000000 0x00000000 0x00000005 0x00000040 0x00000040 0x00000003 0x00000000 [...] CPU Thread 1 APIC ID 1 Topology Processor ID 0, Core ID 1, Thread ID 0 Type 0200400Ah Max CPUID level 00000005h Max CPUID ext. level 8000001Bh Cache descriptor Level 1, I, 64 KB, 1 thread(s) Cache descriptor Level 1, D, 64 KB, 1 thread(s) Cache descriptor Level 2, U, 512 KB, 1 thread(s) Cache descriptor Level 3, U, 6 MB, 2 thread(s) CPUID 0x00000000 0x00000005 0x68747541 0x444D4163 0x69746E65 0x00000001 0x00100F42 0x01020800 0x00802009 0x178BFBFF 0x00000002 0x00000000 0x00000000 0x00000000 0x00000000 0x00000003 0x00000000 0x00000000 0x00000000 0x00000000 0x00000004 0x00000000 0x00000000 0x00000000 0x00000000 0x00000005 0x00000040 0x00000040 0x00000003 0x00000000 [...] Chipset ------------------------------------------------------------------------- Northbridge AMD 790GX rev. 00 Southbridge ATI SB750 rev. 00 Memory Type DDR3 Memory Size 4096 MBytes Channels Dual, (Unganged) Memory Frequency 669.0 MHz (3:10) CAS# latency (CL) 9.0 RAS# to CAS# delay (tRCD) 9 RAS# Precharge (tRP) 9 Cycle Time (tRAS) 24 Bank Cycle Time (tRC) 33 Command Rate (CR) 1T Uncore Frequency 2006.9 MHz Memory SPD ------------------------------------------------------------------------- DIMM # 1 SMBus address 0x50 Memory type DDR3 Module format UDIMM Manufacturer (ID) G.Skill (7F7F7F7FCD000000) Size 2048 MBytes Max bandwidth PC3-10700 (667 MHz) Part number F3-10600CL9-2GBNT Number of banks 8 Nominal Voltage 1.50 Volts EPP no XMP no JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency JEDEC #1 6.0-6-6-17-23 @ 457 MHz JEDEC #2 7.0-7-7-20-27 @ 533 MHz JEDEC #3 8.0-8-8-22-31 @ 609 MHz JEDEC #4 9.0-9-9-25-34 @ 685 MHz DIMM # 2 SMBus address 0x51 Memory type DDR3 Module format UDIMM Manufacturer (ID) G.Skill (7F7F7F7FCD000000) Size 2048 MBytes Max bandwidth PC3-10700 (667 MHz) Part number F3-10600CL9-2GBNT Number of banks 8 Nominal Voltage 1.50 Volts EPP no XMP no JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency JEDEC #1 6.0-6-6-17-23 @ 457 MHz JEDEC #2 7.0-7-7-20-27 @ 533 MHz JEDEC #3 8.0-8-8-22-31 @ 609 MHz JEDEC #4 9.0-9-9-25-34 @ 685 MHz DIMM # 1 SPD registers [...] DIMM # 2 SPD registers [...] Monitoring ------------------------------------------------------------------------- Mainboard Model M4A78T-E (0x000001F7 - 0x00A955E4) LPCIO ------------------------------------------------------------------------- LPCIO Vendor ITE LPCIO Model IT8720 LPCIO Vendor ID 0x90 LPCIO Chip ID 0x8720 LPCIO Revision ID 0x2 Config Mode I/O address 0x2E Config Mode LDN 0x4 Config Mode registers [...] Register space LPC, base address = 0x0290 Hardware Monitors ------------------------------------------------------------------------- Hardware monitor ITE IT87 Voltage 1 1.62 Volts [0x65] (VIN1) Voltage 2 1.15 Volts [0x48] (CPU VCORE) Voltage 3 5.03 Volts [0xBB] (+5V) Voltage 8 3.34 Volts [0xD1] (VBAT) Temperature 0 39°C (102°F) [0x27] (TMPIN0) Temperature 1 43°C (109°F) [0x2B] (TMPIN1) Fan 0 3096 RPM [0xDA] (FANIN0) Register space LPC, base address = 0x0290 [...] Hardware monitor AMD SB6xx/7xx Voltage 0 1.37 Volts [0x1D2] (CPU VCore) Voltage 1 3.50 Volts [0x27B] (CPU IO) Voltage 2 12.68 Volts [0x282] (+12V) Hardware monitor AMD Phenom II X2 550 Power 0 89.10 W (Processor) Temperature 0 35°C (94°F) [0x115] (Core #0) Temperature 1 35°C (94°F) [0x115] (Core #1)

  Read the article

• Is there a WPF "WrapGrid" control available or an easy way to create one?

  - by Jason Coyne

  Essentially I want a wrapPanel, but I would like items to snap to a grid rather than be pressed up to the left, so I can get a nice uniform looking grid, that automatically consumes available space. WrapPanel handles the resize part. WPF.Contrib.AutoGrid handles a nice automatic grid. Anyone got a control that combines them? My use case is I have a series of somewhat irregularly shaped controls. I would like them to appear in nice columns so the wrap panel should snap to the next "tabstop" when placing a control

  Read the article

• SQL Reporting Services - Subreports Broken into multiple columns

  - by devin

  Hi, I inherited an SQL Reporting Services .rdl project from somebody and need help fixing some functionality. In each row of the report, there is a subreport. In order to save space the subreport is divided into 3. Such that in each row of the report, it splits the data of the subreport into 3 smaller tables. Right now, it fills these 3 subreports horizontally. (ie. if the result has 9 values, the first subtable will have 1, 4 & 7, the second subtable will have 2, 5 & 8, etc) Is there a way to have it fill the subtables vertically? (ie. the first subtable would have 1,2 & 3) Thanks!

  Read the article

• Unable to hide TabBar on sub view in iphone

  - by iPhoneDev

  Hello Everyone, My app flow requires Navigation and TabBar controller. So I decided to use TabBar template. Since my first page is login which do not require TabBar, I used presentModelViewController to show Login screen which have Navigation bar if user Navigate to Forgot password. LoginView *rootView = [[[LoginView alloc] init] autorelease]; navigationController= [[[UINavigationController alloc] initWithRootViewController:rootView] autorelease]; [tabBarController presentModalViewController:navigationController animated:FALSE]; Ones the user login I dismiss view controller and show TabBar with 5 Tab and Each Tab contain TabaleView. User select any row and navigate to sub view. The issue is, on sub view I dont need tab bar. (TabBar is needed ONLY on dashboard). If I hide tabBar a white space remain there. Is there any workaround to solve this issue? Please find the screen shot Firt Screen ( presentModelViewController): Second Screen: Issue on sub view:

  Read the article

• Android: how to hide and then show View with animation effect?

  - by tomash

  I have similar question like this one: http://stackoverflow.com/questions/2079074/update-layout-with-the-animation Basically: I have one vertical LinearLayout View with edittext, button and then list. I'd like to hide exittext after pressing button to make more space for list (button will go up). On second press edittext should be visible again. Edittext and button have "wrap_content" height. I'd like to hide and show edittext with animation. I succeeded to animate hiding by overloading Animation's applyTransformation: final float edittextheight= edittext.getHeight(); [....] @Override protected void applyTransformation(float interpolatedTime, Transformation t) { super.applyTransformation(interpolatedTime, t); android.view.ViewGroup.LayoutParams lp = edittext.getLayoutParams(); lp.height = (int)(edittextheight*(1.0-interpolatedTime)); edittext.setLayoutParams(lp); } Problem: I don't know how to calculate height to animate showing - edittext.getHeight(); returns 0 when widget is hidden and in layout definition I'm using "wrap_content". Help?

  Read the article

• Memory leak with JAXB

  - by Anurag

  Hi, I am getting Out of Memory error: Memory Exception in thread "main" java.lang.OutOfMemoryError: Java heap space at org.apache.xerces.dom.CoreDocumentImpl.createElement(CoreDocumentImpl.java:564) I have a standalone Java program which fetches data from DB and create an XML file using DOM. I get the above error if the data fetched is huge, in my case it is 1,000,000 records. I have defined 2GB as heap size while calling the Java class from unix. I tried it with JAXB, but still do not any significant improvement. Any suggestions how to improve the code.

  Read the article

• CSS layout with 2 columns, taking up all width of browser, where left column can collapse

  - by Matt Dawdy

  I want to have a 2 column layout, and have the left column able to be 200 px at first, and have a "shrink" button to shrink it down to 10px, and have the right column expand to fill all the rest of the available space. Then if they click on the "show" button (which will be all they see in the now 10px wide left column) have the left grow back to 200px and have the right column shrink by that amount. I can't figure out how to make the right column grown and shrink without knowing the exact width of the window. I hope this makes sense, and I really hope someone can point me in the right direction. Browser requirements are IE8, FF3.6, Safari, and Chrome, so in theory I can use some advanced CSS techniques. At least I don't have to support IE6.

  Read the article

• Shared Cookies between WebView and HTTPClient?

  - by Arpit

  An Android app I am building requires web authentication for users to make data calls. In Adobe AIR and later the iPhone, we did this by rendering a login page in a webview-equivalent page and setting a cookie when the user signs in. Subsequent data calls use the same Cookie Jar and so are seen as authenticated. In the Android version, I authenticate the user using a WebView and then once thats done, I make a data call using DefaultHttpClient, however I cant seem to load the data on the second call. Is there some cookie gotcha I am missing? I imagine the HTTPClient and WebView would share the same Cookie space. Am I wrong?

  Read the article

• PHP explode not filling in array spot 0

  - by Billy Winterhouse

  I have a file we will call info.txt under UNIX format that has only the following in it: #Dogs #Cats #Birds #Rabbits and am running this against it: $filename = "info.txt"; $fd = fopen ($filename, "r"); $contents = fread ($fd,filesize ($filename)); fclose ($fd); $delimiter = "#"; $insideContent = explode($delimiter, $contents); Now everything looks to be working fine except when I display the array I get the following. [0] => [1] => Dogs [2] => Cats [3] => Birds [4] => Rabbits I checked the .txt file to make sure there wasn't any space or hidden characters in front of the first # so I'm at a loss of why this is happening other than I feel like I'm missing something terribly simple. Any ideas? Thanks in advanced!

  Read the article

• I need to choose a compression algorithm

  - by chiz

  I need to choose a compression algorithm to compress some data. I don't know the type of data I'll be compressing in advance (think of it as kinda like the WinRAR program). I've heard of the following algorithms but I don't know which one I should use. Can anyone post a short list of pros and cons? For my application the first priority is decompression speed; the second priority is space saved. Compression (not decompression) speed is irrelevant. Deflate Implode Plain Huffman bzip2 lzma

  Read the article

• Can two Silverlight applications share IsolatedStorage on one machine?

  - by Edward Tanguay

  What identifies an application and when can two applications share IsolatedStorage if at all, i.e.: if I want to have two Silverlight applications share IsolatedStorage space, is this possible? What kind of "application id" do I need to give to do this? if I don't want two Silverlight applications to share IsolatedStorage, how do I prevent this? Do I need to do this? For instance, I've noticed when I develop a Silverlight application, I can press F5, in the application save to Isolated Storage, stop the application, press F5 again, and it reads from the same IsolatedStorage. (I would think that a new compilation would cause it to use new IsolatedStorage.) However, when I then copy the .xap and .html files to another directory and open the .html file, it does NOT share the IsolatedStorage with the application I was developing. What changed? What is going on behind the scenes here so I know when IsolatedStorage is shared and when it isn't?

  Read the article

• WPF ListView column auto sizing

  - by Diego Mijelshon

  Let's say I have the following ListView: <ListView ScrollViewer.VerticalScrollBarVisibility="Auto"> <ListView.View> <GridView> <GridViewColumn Header="Something" DisplayMemberBinding="{Binding Path=ShortText}" /> <GridViewColumn Header="Description" DisplayMemberBinding="{Binding Path=VeryLongTextWithCRs}" /> <GridViewColumn Header="Something Else" DisplayMemberBinding="{Binding Path=AnotherShortText}" /> </GridView> </ListView.View> </ListView> I'd like the short text columns to always fit in the screen, and the long text column to use the remaining space, word-wrapping if necessary. Is that possible?

  Read the article

• SQL Server 2005 high memory usage and performance problems

  - by emzero

  Hi there guys. I have this ASP.NET/SQLServer2005 website running on a production server (Win2003, QuadCore, 4GB). The site runs smoothly normally, but after 2-3 weeks I notice a slow performance on the site (especifically in one particular page). Also I notice that the SQL Server process is using like 2GBs of RAM. So I restart the service, the site runs fast again and the process 300-400MBs. I'm looking for an explanation of why is this happening? What is SQL Server storing in RAM that takes too much space and degrades the performance? What can I do to avoid this? I'm trying to avoid restarting the SQLServer everytime this happens. Thank you!

  Read the article

• alternative to visibility:collapse not working on IE and Chrome

  - by tic

  The following page: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <STYLE type="text/css"> tr.cccc { visibility: collapse; } </STYLE> <BODY> <TABLE border="1"> <TR class="cccc"> <TD>one</TD> </TR> </TABLE> </BODY> </HTML> works only in Firefox. IE always displays the row, and Chrome hides the row but showing its vertical space. So, how can I hide completely a row using only CSS? Thanks.

  Read the article

• Best approach for GPGPU/CUDA/OpenCL in Java?

  - by Frederik

  General-purpose computing on graphics processing units (GPGPU) is a very attractive concept to harness the power of the GPU for any kind of computing. I'd love to use GPGPU for image processing, particles, and fast geometric operations. Right now, it seems the two contenders in this space are CUDA and OpenCL. I'd like to know: Is OpenCL usable yet from Java on Windows/Mac? What are the libraries ways to interface to OpenCL/CUDA? Is using JNA directly an option? Am I forgetting something? Any real-world experience/examples/war stories are appreciated.

  Read the article

• Wrapping/warping a CALayer/UIView (or OpenGL) in 3D (iPhone)

  - by jbrennan

  I've got a UIView (and thus a CALayer) which I'm trying to warp or bend slightly in 3D space. That is, imagine my UIView is a flat label which I want to partially wrap around a beer bottle (not 360 degrees around, just on one "side"). I figured this would be possible by applying a transform to the view's layer, but as far as I can tell, this transform is limited to rotation, scale and translation of the layer uniformly. I could be wrong here, as my linear algebra is foggy at this point, to say the least. How can I achieve this?

  Read the article

• jQuery, insertBefore, validation, Placement of error message

  - by Steve

  I am using insertBefore under errorplacement to add validation messages, each one below each other as I want the order of the messages to go from top to bottom. I am using a hidden input at the very bottom of a parent element in order to supply an element for the insertBefore argument. Is there a way to insert from the bottom without using the dummy hidden element? If I use absolute positioning, there is a possibility for white space, for example 3 stacked messages, the middle one missing since there is no collapsing with absolute positioning.

  Read the article

• Data Structures

  - by Phoenix

  There is a large stream of numbers coming in such as 5 6 7 2 3 1 2 3 .. What kind of data structure is suitable for this problem given the constraints that elements must be inserted in descending order and duplicates should be eliminated. I am not looking for any code just ideas? I was thinking of a Self-Balancing BST where we could add the condition that all nodes < current node on left and all nodes current node on right, this takes care of the duplicates .. but i don't think they are necessarily inserted in descending order. Any ideas what might be a better choice .. ofcourse it needs to be efficient time and space wise.

  Read the article

• UITableView: Juxtaposing row, header, and footer insertions/deletions

  - by jdandrea

  Consider a very simple UITableView with one of two states. First state: One (overall) table footer One section containing two rows, a section header, and a section footer Second state: No table footer One section containing four rows and no section header/footer In both cases, each row is essentially one of four possible UITableViewCell objects, each containing its own UITextField. We don't even bother with reuse or caching, since we're only dealing with four known cells in this case. They've been created in an accompanying XIB, so we already have them all wired up and ready to go. Now consider we want to toggle between the two states. Sounds easy enough. Let's suppose our view controller's right bar button item provides the toggling support. We'll also track the current state with an ivar and enumeration. To be explicit for a sec, here's how one might go from state 1 to 2. (Presume we handle the bar button item's title as well.) In short, we want to clear out our table's footer view, then insert the third and fourth rows. We batch this inside an update block like so: // Brute forced references to the third and fourth rows in section 0 NSUInteger row02[] = {0, 2}; NSUInteger row03[] = {0, 3}; [self.tableView beginUpdates]; state = tableStateTwo; // 'internal' iVar, not a property self.tableView.tableFooterView = nil; [self.tableView insertRowsAtIndexPaths:[NSArray arrayWithObjects: [NSIndexPath indexPathWithIndexes:row02 length:2], [NSIndexPath indexPathWithIndexes:row03 length:2], nil] withRowAnimation:UITableViewRowAnimationFade]; [self.tableView endUpdates]; For the reverse, we want to reassign the table footer view (which, like the cells, is in the XIB ready and waiting), and remove the last two rows: // Use row02 and row03 from earlier snippet [self.tableView beginUpdates]; state = tableStateOne; self.tableView.tableFooterView = theTableFooterView; [self.tableView deleteRowsAtIndexPaths:[NSArray arrayWithObjects: [NSIndexPath indexPathWithIndexes:row02 length:2], [NSIndexPath indexPathWithIndexes:row03 length:2], nil] withRowAnimation:UITableViewRowAnimationFade]; [self.tableView endUpdates]; Now, when the table asks for rows, it's very cut and dry. The first two cells are the same in both cases. Only the last two appear/disappear depending on the state. The state ivar is consulted when the Table View asks for things like number of rows in a section, height for header/footer in a section, or view for header/footer in a section. This last bit is also where I'm running into trouble. Using the above logic, section 0's header/footer does not disappear. Specifically, the footer stays below the inserted rows, but the header now overlays the topmost row. If we switch back to state one, the section footer is removed, but the section header remains. How about using [self.tableView reloadData] then? Sure, why not. We take care not to use it inside the update block, per Apple's advisement, and simply add it after endUpdates. This time, good news! The section 0 header/footer disappears. :) However ... Toggling back to state one results in a most exquisite mess! The section 0 header returns, only to overlay the first row once again (instead of appear above it). The section 0 footer is placed below the last row just fine, but the overall table footer - now reinstated - overlays the section footer. Waaaaaah … now what? Just to be sure, let's toggle back to state two again. Yep, that looks fine. Coming back to state one? Yecccch. I also tried sprinkling in a few other stunts like using reloadSections:withRowAnimation:, but that only serves to make things worse. NSRange range = {0, 1}; NSIndexSet *indexSet = [NSIndexSet indexSetWithIndexesInRange:range]; ... [self.tableView reloadSections:indexSet withRowAnimation:UITableViewRowAnimationFade]; Case in point: If we invoke reloadSections... just before the end of the update block, changing to state two hides the first two rows from view, even though the space they would otherwise occupy remains. Switching back to state one returns section 0's header/footer to normal, but those first two rows remain invisible. Case two: Moving reloadSections... to just after the update block but before reloadData results in all rows becoming invisible! (I refer to the row as being invisible because, during tracing, tableView:cellForRowAtIndexPath: is returning bona-fide cell objects for those rows.) Case three: Moving reloadSections... after tableView:cellForRowAtIndexPath: brings us a bit closer, but the section 0 header/footer never returns when switching back to state one. Hmm. Perhaps it's a faux pas using both reloadSections... and reloadData, based on what I'm seeing at trace-time, which brings us to: Case four: Replacing reloadData with reloadSections... outright. All cells in state two disappear. All cells in state one remain missing as well (though the space is kept). So much for that theory. :) Tracing through the code, the cell and view objects, as well as the section heights, are all where they should be at the opportune times. They just aren't rendering sanely. So, how to crack this case? Clues welcome/appreciated!

  Read the article

< Previous Page | 228 229 230 231 232 233 234 235 236 237 238 239  | Next Page >