Search Results

Search found 7941 results on 318 pages for 'formatting word'.

Page 232/318 | < Previous Page | 228 229 230 231 232 233 234 235 236 237 238 239  | Next Page >

  • windows 7: Event 55 The file system structure on the disk is corrupt and unusable

    - by Radio
    Here is a real bad one! Windows 7 RTM with SP1 installed [Version 6.1.7601]. Recently tried to delete some folder on my hard drive and Windows prompted "Error 0x80070570: The file or directory is corrupted and unreadable", and at the same time placed an Event 55 describing "The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on \Device\HarddiskVolume2." Ran chkdsk, first with /f option, then with /r option. Result in both cases was: no errors found, 0 bad sectors. No problems chkdsk found at all! Went through StackExchange, Google and spent over 6 hours on this. Still cannot figure out the problem. Re-installing/Re-Formatting is not an option! What did I try: Hotfix - Windows6.1-KB982927-x64.msu - gave me an error about incompatibility with my computer, however it totally matches my system. CRC of hotfix was ok. Windows Repair Console found startup errors and fixed those, but this didn't help an issue, even by running chkdsk c: /R from it. http://support.microsoft.com/kb/246026 does not promise anything good. sfc /scannow does not help too. Replaced hard drive by cloning an old one using True Image, repeated all steps above. At the same time, some minor glitches started to appear in my Windows, like side panel and notification area settings are getting reset. Goal is to delete the folder and get rid of Event 55. Sounds like NTFS bug. Please help. This is completely ridiculous.

    Read the article

  • Windows 8.1 - Won't boot (0xc000000f), bcdedit fails

    - by user3014097
    I’m pretty much stuck at this point. So, backstory: Windows was installed on one of the SSDs currently in my tower. I bought a new SSD to install Windows (8.1 64 bit) on. Windows installation went fine, booted up, and formatted the old SSD from within Windows (this seems to have been a mistake, but I didn’t realize that at the time). Despite formatting the old SSD, whenever I tried to boot I was told that there were 2 Windows installations. Apparently, when I formatted the old drive, not all of the partitions were removed. So, I booted up with the repair utility, went into cmd, and deleted the non-primary partitions on the old SSD (there were 2 – think they were system and recovery, although I’m forgetting now). Reboot – computer won’t boot. Getting the 0xc000000f “The boot selection failed because a required device is inaccessible” error. Troubleshooting so far: Automatic repair doesn’t fix anything (I’ve never had luck with it though) If I go to install a new version of Windows, the drives and partitions are all there. The SSD is functioning, I at least know that. I’ve essentially gone through this guide: https://neosmart.net/wiki/recovering-windows-bootloader/ Unfortunately, I’m not getting anywhere. I’m not even entirely sure how to describe the errors I’m getting, so I’ve just included pictures of every step (I can't actually post them though so I just included a photobucket link). http://s319.photobucket.com/user/DGalt11/library/Computer%20Issue Am I completely screwed here (i.e. reformat and reinstall?)? Thanks

    Read the article

  • Formatted C: from Windows 7 setup, now it won't even install

    - by ocurro
    Help, I'm so confused. I did more or less what's been described here: I formatted Vista and installed Windows 7 over it. Problem is that I'm now unable to boot (...) [1] I'm installing Seven on top of Vista on ACER AS1410 Notebook When it comes to the part where I choose where to install, I pick the partition labeled C: but instead of keeping windows.old files (what would I want them for?) I choose to go and carelessly format the partition (my bad). It shows me this error: Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information Now the only option is "Load Driver". i have tried installing every single one from ACER website, none of them are useful. I even flashed orig. BIOS. I've tried going back and choose "Repair" like in the picture:[2] but I only get an error: "Failed to save startup options" I think this is weird, what else can I do? [1] superuser.com/questions/117076/formatting-of-an-xp-vista-dual-boot-machine-now-unable-to-boot-up-xp [2] www.howtogeek.com/wp-content/uploads/2007/08/image51.png

    Read the article

  • How do I disable the firewall on blackberry?

    - by user15660
    I own a Blackberry 9630 tour.(Sprint). The firewall is enabled with a lock sign and grayed out. I'm not able to disable it. Because of this many of my blackberry apps don't work as it gives a message "The application has tried to open a connection that's not allowed by your IT policy". I tried all options and there's nothing to disable. This is a personal blackberry and I don't have an IT policy on it. I did all methods like wiping, formatting/resetting to factory settings acc. to blackberry site by running their reset app from PC etc etc. but nothing works I tried CrackUtil for blackberry and that worked and wiped the blackberry. I restored my bb and started using it just to notice that the firewall is enabled back after a desktop manager connection to PC. I even made sure the policy.bin file on PC is a regular one with no IT policy. How do I get this disabled? I had the same problem on my old blackberry 8330 and crackutil disabled the firewall. but after a few days after a desktop manager update of blackberry OS and other small stuff the firewall got enabled again. Please give me a solutions to disable the firewall on blackberry

    Read the article

  • Why can't I route to some sites from my MacBook Pro that I can see from my iPad? [closed]

    - by Robert Atkins
    I am on M1 Cable (residential) broadband in Singapore. I have an intermittent problem routing to some sites from my MacBook Pro—often Google-related sites (arduino.googlecode.com and ajax.googleapis.com right now, but sometimes even gmail.com.) This prevents StackExchange chat from working, for instance. Funny thing is, my iPad can route to those sites and they're on the same wireless network! I can ping the sites, but not traceroute to them which I find odd. That I can get through via the iPad implies the problem is with the MBP. In any case, calling M1 support is... not helpful. I get the same behaviour when I bypass the Airport Express entirely and plug the MBP directly into the cable modem. Can anybody explain a) how this is even possible and b) how to fix it? mella:~ ratkins$ ping ajax.googleapis.com PING googleapis.l.google.com (209.85.132.95): 56 data bytes 64 bytes from 209.85.132.95: icmp_seq=0 ttl=50 time=11.488 ms 64 bytes from 209.85.132.95: icmp_seq=1 ttl=53 time=13.012 ms 64 bytes from 209.85.132.95: icmp_seq=2 ttl=53 time=13.048 ms ^C --- googleapis.l.google.com ping statistics --- 3 packets transmitted, 3 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 11.488/12.516/13.048/0.727 ms mella:~ ratkins$ traceroute ajax.googleapis.com traceroute to googleapis.l.google.com (209.85.132.95), 64 hops max, 52 byte packets traceroute: sendto: No route to host 1 traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 *traceroute: sendto: No route to host traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 ^C mella:~ ratkins$ The traceroute from the iPad goes (and I'm copying this by hand): 10.0.1.1 119.56.34.1 172.20.8.222 172.31.253.11 202.65.245.1 202.65.245.142 209.85.243.156 72.14.233.145 209.85.132.82 From the MBP, I can't traceroute to any of the IPs from 172.20.8.222 onwards. [For extra flavour, not being able to access the above appears to stop me logging in to Server Fault via OpenID and formatting the above traceroutes correctly. Anyone with sufficient rep here to do so, I'd be much obliged.]

    Read the article

  • Using UDF on a USB flash drive

    - by CesarB
    After failing to copy a file bigger than 4G to my 8G USB flash drive, I formatted it as ext3. While this is working fine for me so far, it will cause problems if I want to use it to copy files to someone which does not use Linux. I am thinking of formatting it as UDF instead, which I hope would allow it to be read (and possibly even written) on the three most popular operating systems (Windows, MacOS, and Linux), without having to install any extra drivers. However, from what I found on the web already, there seem to be several small gotchas related to which parameters are used to create the filesystem, which can reduce the compability (but most of the pages I found are about optical media, not USB flash drives). I would like to know: Which utility should I use to create the filesystem? (So far I have found mkudffs and genisoimage, and mkudffs seems the best option.) Which parameters should I use with the chosen utility for maximum compability? How compatible with the most common versions of these three operating systems UDF actually is? Is using UDF actually the best idea? Is there another filesystem which would have better compatibility, with no problematic restrictions like the FAT32 4G file size limit, and without having to install special drivers in every single computer which touches it?

    Read the article

  • How to fix a bootable USB Kubuntu installation when the drive has maxed out?

    - by NoCatharsis
    I used Universal-USB-Installer-v1.5.1 from PenDriveLinux.com with Kubuntu 10.04 so I could set up my 4GB flash drive as a totally independent installation. Unfortunately, there was an OS upgrade available which Kubuntu downloaded and attempted to install. This, along with some other software, apparently maxed out my drive before I realized it. Now when I try to boot from the drive, everything boots as normal to the OS boot screen where I select "Boot from this Kubuntu USB Installation." The startup process initiates, then stalls about halfway through and hangs indefinitely. I'm guessing the drive is trying to use space it doesn't have and completely stops working. I realize that once the OS upgrade is in place, the old files could be deleted for a potential 700MB space gain. However, I just have no way to get into the OS and complete the upgrade. My main OS is Windows 7. Is there a way I can fix this issue from within Windows without formatting the entire drive and reinstalling Kubuntu from scratch?

    Read the article

  • How can I wipe my iPod classic and fix any bad sectors on the hard drive without killing it?

    - by Sam Meldrum
    My iPod never finishes syncing and only syncs audio, not pictures or video - any ideas as to how I can fix it? My iPod classic 160GB worked well for a couple of years. I used to sync a lot of photos at full resolution to it, but this recently stopped working after I moved to Windows 7. iTunes is on latest version - 9.1.1.12 iPod software is up to date - 1.1.2 Windows 7 is fully up to date and patched The symptoms are that the iPod will start to sync, all audio (music and podcasts will sync successfully) but the syncing will then just appear to continue - itunes message: Syncing iPod. Do not Disconnect. This sync never completes - I have left it trying for days. I have tried resetting the iPod using the Restore button, whereupon it restarts sync from default options and again will sync audio, but nothing else. I suspect that something has gone wrong on the hard-drive - either a bad sector or some corrupt data. Is there a process I can go through to fix this? E.g. SpinRite or a format? If so how do I go about formatting an iPod and will it be recognised as an iPod after format and work as normal? Any advice on what to try next much appreciated? Update I have eliminated problems with the files, PC or iTunes as they sync fine to other iPods. I have also eliminated the cable by trying different cables which work with other iPods. What I'd really like to know is if there is any way to more fundamentally wipe the iPod safely, attempt to repair any bad sectors on the hard drive and then start from scratch. Anyone ever managed this?

    Read the article

  • How to open semicolon delimited CSV-files in US-version of Excel

    - by Holgerwa
    When I double-click on a .csv file, it is opened in Excel. The csv-files have columns delimited with semicolons (not commas, but also a valid format). Using a German Windows/Excel setup, the opened file is displayed correctly, the columns are separated where the semicolons existed in the csv-file. But when I do the same on an (US-) English Windows/Excel setup, only one column is imported, showing the whole data including the semicolons in the first column. (I don't have an English setup available for tests, users have reported the behavior) I tried to change the list separator value in Windows regional settings, but that didn't change anything. What can I do to be able to double-click-open those CSV-files on an English setup? EDIT: It seems to be the best solution not to rely on CSV-files in this case. I was hoping that there is some formatting for CSV-files that makes it possible to use them internationally. The best solution seems that I'll switch to creating XLS-files. Thanks to all for your suggestions and helpful tips!

    Read the article

  • Clipboard bug in Wordpad in Windows 7 (accidentally pasting large file into application)

    - by frenchglen
    In Win7, I use Wordpad, and I really like it. For my needs it's lean and fast, yet has the formatting functionalities I'm after when working on my TXT/RTF files on a daily basis. I don't intend to change text editors. There's a really bad bug which has ALWAYS plagued me. If you have a large file contained in the clipboard, like a 238MB FLAC file, and you accidentally paste it into Wordpad for whatever reason - it hangs the application for a VERY long time (like 2 hours, it depends on how big the file is, because it tries to 'handle' it). You either have to close the application and lose any unsaved changes, or go do something else until the item has finished pasting into Wordpad (it actually eventually drops the file's icon in wordpad just like how it appears in Windows Explorer). It's a Windows bug, a Wordpad bug. Is there some solution for this? Or is the problem fixed in Windows 8 (if anyone can tell me)? .....I'm not going to try out Win8 myself, merely to answer this question - that's what I'm asking it on SuperUSer for! I'm really hoping it's one of those little-yet-big things that they've fixed in Win8 (like removing the 255-character file path limit in Explorer, which is awesome). Thank you for your help, if you have Win8 handy and can test this. :)

    Read the article

  • Cross OS data recover question, USB drive involved.

    - by Moshe
    Here's the story: A MacBook had OS X 10.4 and Windows XP dual booting using rEFIt. Then the Windows partition gets corrupted and it won't boot. Presumably a virus. There were sensitive files there and those were successfully copied to a USB drive and then 10.5 was installed on the hard drive, formatting the drive in the process. The USB drive's contacts cracked and he data is lost from there, unless it can be resoldered. The issues is that there is too much solder there already. So, how can the data in question be recovered? The files were Microsoft Money (not the latest version) files for the Windows version of the program. Right now, only OS X is installed on the MacBook. Is there Mac based program that can recover the Windows data or am I better off trying to resolder the drive? Does anyone know how to best resolder a USB drive more than once, where the first solder is ther, but detached from the silicon? Also, what format (extension) are Microsoft Money files? In need of help!

    Read the article

  • My iPod never finishes syncing and only syncs audio, not pictures or video - any ideas as to how I c

    - by Sam Meldrum
    My iPod classic 160GB worked well for a couple of years. I used to sync a lot of photos at full resolution to it, but this recently stopped working after I moved to Windows 7. iTunes is on latest version - 9.1.1.12 iPod software is up to date - 1.1.2 Windows 7 is fully up to date and patched The symptoms are that the iPod will start to sync, all audio (music and podcasts will sync successfully) but the syncing will then just appear to continue - itunes message: Syncing iPod. Do not Disconnect. This sync never completes - I have left it trying for days. I have tried resetting the iPod using the Restore button, whereupon it restarts sync from default options and again will sync audio, but nothing else. I suspect that something has gone wrong on the hard-drive - either a bad sector or some corrupt data. Is there a process I can go through to fix this? E.g. SpinRite or a format? If so how do I go about formatting an iPod and will it be recognised as an iPod after format and work as normal? Any advice on what to try next much appreciated?

    Read the article

  • Windows 8 Doesn't Shutdown Properly With Fast Start-Up Enabled

    - by Patrick
    While Fast start-up is enabled, on turning the computer off (shutdown) the computer idles for about 5min after logging out/screen turning off. It then turns off. On returning into Windows I receive the error message saying Windows didn't shut down properly. Hibernate works fine, and I am told this shouldn't be the case - If one doesn't work, neither should. It works when both Fast start-up is enabled and disabled, as does restart and sleep. Windows is installed under UEFI. The UEFI ultra fast boot option for my motherboard cannot be enabled as my GPU doesn't support some UEFI GOP tech. As far as I know, not related to windows fast start-up, but thought it was worth mentioning. To clarify, if this: http://www.eightforums.com/tutorials/6320-fast-startup-turn-off-windows-8-a.html is enabled, the computer does not shut down properly. EDIT: Some more information on the matter: Formatting didn't fix the issue. Still fails regardless of drivers installed. Hardware was purchased ~6months ago. Running a good SSD. Event viewer Always these two messages in close succession: Error (event ID 6008): The previous system shutdown at 7:45:21 PM on ?27/?10/?2012 was unexpected. Critical (kernel power, event ID 41): The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Upon installing WPT as suggested below to figure out what was happening during shutdown, and running the cmd xbootmgr -trace shutdown -noPrepReboot -traceFlags BASE+CSWITCH+DRIVERS+POWER -resultPath C:\TEMP Windows fast start-up is now working consistently. Still works upon uninstalling WPT. This is the only change to occur on the computer. Nothing else has bee installed/uninstalled, no Windows Updates, nothing. Windows fast start-up did not work prior to installing WPT and running the cmd (made sure I tested).

    Read the article

  • Screen Flickering: Hardware or Software?

    - by Wesley
    I have a Samsung N120 netbook (upgraded to 2GB DDR2 RAM) and there has been a screen flickering issue for some time now. However, I have not been able to accurately determine whether it is a software or hardware issue. Here are some of the symptoms: The flicker is white-colored and shows up as vertical lines. Flickering or not, there may be occasionally some random blue patterns (no image distortion) The screen tends to flicker more when the screen is not tilted back all the way. When tilting the screen back and forth, the screen will usually flicker. Some images on the screen may randomly distort without full-on flickering. The screen will flicker only on certain websites, but not on others. A certain part of a webpage may constantly be distorted randomly, even when scrolling. While flickering, the mouse will not move though I'm moving my finger along the touchpad. A connected external monitor does not have any problems. The flickering is completely random and does not seem to follow any CPU/GPU usage trends. Flickering usually gets worse when the screen brightness is turned higher. There will be flickering on battery and while plugged in. Search up "Samsung N120 - Screen Flickering" on YouTube for an idea of what the flickering looks like. However, there is no visible distortions and the flickering seems to stop when the screen has dimmed. Since the problems started, I tried formatting and using Windows 7, then formatted again and went back to Windows XP. The screen was also replaced sometime during this past summer. The uninstallation of the Samsung Battery Manager (on the original install of XP) seemed to reduce the flicker partially, but eventually got worse. So, what could possibly be the problem?

    Read the article

  • Permission issue for apache

    - by Aamir Adnan
    Environment Details: Amazon Ec2 Ubuntu 12.04 Django + mod_wsgi + python 2.6 web server: apache2 I have mounted a 10GB ebs volume to an instance to /mnt/ebs1/. After mounting the volume and formatting, I have placed all my project files in /mnt/ebs1/project. the wsgi file is in /mnt/ebs1/project/apache/django.wsgi. The content of wsgi file is: import os, sys sys.path.insert(0, '/mnt/ebs1/project') sys.path.insert(1, '/mnt/ebs1') os.environ['DJANGO_SETTINGS_MODULE'] = 'project.configs.common.settings' import django.core.handlers.wsgi application = django.core.handlers.wsgi.WSGIHandler() My httpd.conf file looks as: LoadModule wsgi_module /usr/lib/apache2/modules/mod_wsgi.so WSGIPythonHome /usr/bin/python2.6 WSGIScriptAlias / /mnt/ebs1/project/apache/django.wsgi <Directory /mnt/ebs1/project> Order allow,deny Allow from all </Directory> <Directory /mnt/ebs1/project/apache> Order allow,deny Allow from all </Directory> Alias /static/ /mnt/ebs1/project/static/ <Directory /mnt/ebs1/project/static> Order deny,allow Allow from all </Directory> The above configurations gives me Forbidden: You don't have permission to access / on this server. I tried to find the user which is running apache using ps aux which is www-data and has group www-data. I have tried to change the ownership of /mnt/ebs1 and its subdirectories using chown -R www-data:www-data /mnt/ebs1 but that still does not solve the problem. Can any one tell me what I am doing wrong or have missed?

    Read the article

  • The USB mouse sticks in Windows 7 after automatic attempt to fix the boot

    - by chelder
    Avast Antivirus asked me to delete a probable virus and to restart to perform a checking. I had to stop the checking at the middle of the procedure as I needed the computer. It was imposible to turn off the computer pushing the power button (as it entered in suspension mode, no matter how long I kept pushed the power button). I removed the battery as the only way to restart the computer. Windows 7 said that there is a problem to iniziate Windows. Windows 7 tried to fix the problem without success. Windows 7 started after that though. Everything is OK but the USB mouse. The USB mouse sticks and freezes each couple of seconds more or less. The tactile mouse (PS2) works well. I googled for solutions but the posible solutions didn't work for me. What happened? How could I fix it without formatting and reinstalling everything? UPDATE: this is what I did: Change the mouse from one usb port to another Test another mouse Set the number of cores of the CPU manually with msconfig Power management: not disable usb ports Check hard disk errors

    Read the article

  • If I partition a drive connected via eSata will it show different partitions when connected via USB?

    - by jeffreypriebe
    I have an odd problem with an external drive. I'm formatting it connected to my laptop prior to connecting it to my router. The HDD enclosure has both an eSata and USB connections. Generally, I connect it via eSata to my laptop. I created my partitions and connected it to the router, but I see partition information that is different than what I created. After chasing leads concerning large HDD size, I mindlessly connected the HDD to my laptop with USB. Lo! I see the same partitions as the router. Attached are screenshots using the same program and the HDD in question. The only difference is the connection. For the first, I connected via eSata and hit "refresh" on the partition program. Then, turned off the HDD, disconnected the eSata cable, and connected via USB. Power and refresh. eSata: reports a total HDD size of 2328 GB, with four partitions (the third being 1.96TB) USB: reports a total HDD size of 280 GB, with three partitions (the third being 279 GB) Any idea why this is happening? It looks like it clearly is an issue of the 4K sector size and not playing nice with the USB enclosure. I tried it eSata and USB in Windows and Linux and it appears consistently that eSata is reporting correctly, USB incorrectly.

    Read the article

  • Are flash drives and hard drives thought of as "an ocean of bytes"?

    - by Jian Lin
    Why can a USB Flash drive be formatted as NTFS or FAT32? Is the USB Flash Drive and Hard Drive just to be thought of as "an ocean of bytes"? I get very used to hearing formatting a hard drive as FAT32 or NTFS, but we can also format a USB Flash drive as NTFS or FAT32? Is it because a hard drive or Flash drive both can be thought of as "an ocean of bits" or "an ocean of bytes"? I remember RAM as: it takes 16 bit or 32 bit as an address signal (the 16 or 32 copper footing on the circuit board), and give out 8 bit of data (the other 8 copper footing on the circuit board). So can a hard drive be thought of as working that way too? So that's why a Flash drive can be the same too? Just an "ocean of bytes". But is it true that hard drive's hardware make it an ocean of sector or something else, that is, the smaller unit of read / write is not byte but something else? So with this "ocean of bytes", NTFS has the format that says, "if the first byte is __, then it means __ (it is a file or folder, and link to which sector, indicated by byte 2 and 3, etc, etc)"

    Read the article

  • How can I wipe my iPod classic and fix any bad sectors on the hard drive without killing it?

    - by Sam Meldrum
    My iPod never finishes syncing and only syncs audio, not pictures or video. Any ideas as to how I can fix it? My iPod classic 160GB worked well for a couple of years. I used to sync a lot of photos at full resolution to it, but this recently stopped working after I moved to Windows 7. iTunes is on latest version - 9.1.1.12 iPod software is up to date - 1.1.2 Windows 7 is fully up to date and patched The symptoms are that the iPod will start to sync, all audio (music and podcasts will sync successfully) but the syncing will then just appear to continue - itunes message: Syncing iPod. Do not Disconnect. This sync never completes - I have left it trying for days. I have tried resetting the iPod using the Restore button, whereupon it restarts sync from default options and again will sync audio, but nothing else. I suspect that something has gone wrong on the hard-drive - either a bad sector or some corrupt data. Is there a process I can go through to fix this? E.g. SpinRite or a format? If so how do I go about formatting an iPod and will it be recognised as an iPod after format and work as normal? Any advice on what to try next much appreciated? Update I have eliminated problems with the files, PC or iTunes as they sync fine to other iPods. I have also eliminated the cable by trying different cables which work with other iPods. What I'd really like to know is if there is any way to more fundamentally wipe the iPod safely, attempt to repair any bad sectors on the hard drive and then start from scratch. Anyone ever managed this?

    Read the article

  • Issues with VSFTPD / FTP on Linux Ubuntu server - Steps for Troubleshooting?

    - by jnolte
    I am dealing with an issue I am unclear on how to resolve and have been pulling my hair out for some time. I have been trying to configure an FTP user using the following (we use this same documentation on all servers) Install FTP Server apt-get install vsftpd Enable local_enable and write_enable to YES and anonymous user to NO in /etc/vsftpd.conf restart - service vsftpd restart - to allow changes to take place Add WordPress User for FTP access in WP Admin Create a fake shell for the user add "usr/sbin/nologin" to the bottom of the /etc/shells file Add a FTP user account useradd username -d /var/www/ -s /usr/sbin/nologin passwd username add these lines to the bottom of /etc/vsftpd.conf - userlist_file=/etc/vsftpd.userlist - userlist_enable=YES - userlist_deny=NO Add username to the list at top of /etc/vsftpd.userlist restart vsftpd "service vsftpd restart" make sure firewall is open for ftp "ufw allow ftp" allow modify the /var/www directory for username "chown -R /var/www I have also went through everything listed on this post and no luck. I am getting connection refused. Sorry for the poor text formatting above. I think you get the idea. This is something we do over and over and for some reason it is not cooperating here. Setup is Ubuntu 12.04LTS and VSFTPD v2.3.5 Thank you in advance.

    Read the article

  • Apache and Virtual Hosts Problem on OS X

    - by Charles Chadwick
    I recently formatted and installed my iMac. I am running 10.6.5. Prior to this format, I had the default Apache web server up and running with several virtual hosts, and everything ran beautifully. After formatting, I set everything back up again, and now Apache is acting funny. Here is a description of what I have going on. My default root directory for the Apache Web server is pointed to an external hard drive. In my httpd.conf, here is what I have: DocumentRoot "/Storage/Sites" Then a few lines beneath that: <Directory /> Options FollowSymLinks AllowOverride All Order deny,allow Allow from all </Directory> And then beneath that: <Directory "/Storage/Sites"> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny Allow from All </Directory> At the end of this file, I have commented out the user dir include conf file: Include /private/etc/apache2/extra/httpd-userdir.conf And uncommented the virtual hosts conf file: Include /private/etc/apache2/extra/httpd-vhosts.conf Moving on, I have the following entry in my vhosts file: <VirtualHost *:80> DocumentRoot "/Storage/Sites/mysite" ServerName mysite.dev </VirtualHost> I also have a host record in my /etc/hosts file that points mysite.dev to 127.0.0.1 (I also tried using my router IP, 192.168.1.2). The problem I am coming across is, despite having PHP files in /Storage/Sites/mysite, the server is still looking at /Storage/Sites. I know this because in the DocumentRoot contains a php file with phpinfo() (whereas the index.php file in mysite has different code). I have tried setting up other virtual hosts, but they are still doing the same thing. Also, "NameVirtualHost *:80" is in my vhosts file. I saw as a solution on another thread here. Doesn't seem to make a difference. Any ideas on this? Let me know if this is not enough information.

    Read the article

  • Cannot delete flash9.ocx

    - by Kara Marfia
    Some kinda voodoo, indeed. Bought a new boot drive, and it's time to use the old drive for data. I thought I'd save some time by just wiping the unneeded system folders, instead of backing up, formatting, and restoring. Wups! I have a single Adobe file that absolutely will not be deleted. G:\Windows\SysWOW64\Macromed\Flash\flash9.ocx - though it may have started with a different file name. I'm able to rename it, oddly enough. To be clear, the drive is currently plugged in externally. So I can boot the computer, plug this drive in afterward, and immediately attempt to delete. "File in use" box reads "the action can't be completed because the file is open in another program". I'd format at this point, but it's my white whale, and I have to know if Adobe has inserted some nasty little registry hack - or whatever it is - making this impossible. Since I'm sure it'll come up, I've taken ownership of the file - and this was the trick preventing me from deleting anything else on the drive - full rights on the file permissions, you name it, I've fiddled with the file itself. I'm about to try uninstalling flash from the system drive, in case that aligns the planets properly. Sometimes I wish I were less stubborn, and could just format already.

    Read the article

  • Can not copy files after installing windows

    - by Ali
    I am experiencing a weird problem. I was running Xubuntu on my laptop until yesterday that I had to delete Xubuntu and install Windows. I had a NTFS partition on my Xubuntu that I kept some files on it. Today after installing windows I wanted to move all the files from that partition to an external HDD. I selected all files and folders and clicked on Copy, then I went to the HDD and clicked on paste but nothing happened. I can not do that. I do not know why. I copy the files, and wherever I click paste, nothing happens. If I try to copy the files and folders one by one, I can copy some of them, but some of them do not move. The other problem I have is that I can not open some files, in particular pdf files. When I click on pdf files I get this error: There was an error opening this document. This file cannot be found. Also, I cannot play some mp4 files. I can not open some jpg and txt files. I get this error The directory name is invalid. So in summary, after removing Xubuntu and installing windows 7 I have the following problems with one of the NTFS partitions on my internal drive: Can not copy or cut all folders and files from that partition to any other partition - I also do not get any errors. Can copy some folders and files Can not access some pdf, jpeg, txt and mp4 files and get the above errors. I should also mention I did not change anything for this partition during the installation or formatting the other partitions.

    Read the article

  • Recover hard disk from Raw format

    - by user1632736
    I have been all over the web today with no results. So my drive was encrypted (truecrypt) the whole drive where windows resided. I decided to partition it to install W8 and forgot it was encrypted. So the drive got damaged and not accessible. When connected to a computer it asks for formatting. Somehow I enabled the drive through TrueCrypt on another computer and I could see and get all the files. Then I decided to decrypt the drive thinking that everything would be back to normal. After decryption my drive is not NTFS it is in RAW format. I am trying every possible way to recover, and I am desperate enough to ask lol. I tried: ddrescue (linux) (not mountable, no signature, ntfsfix no good) testdisk (linux and windows) Sees the partitions but cant do anything Many recovery applications. etc etc. I read in different places that doing a quickformat to NTFS and then doing a data recovery might help. I would definitely like a second opinion. Any suggestion would be really helpful

    Read the article

  • How to import a text file into powershell and email it, formatted as HTML

    - by Don
    I'm trying to get a list of all Exchange accounts, format them in descending order from largest mailbox and put that data into an email in HTML format to email to myself. So far I can get the data, push it to a text file as well as create an email and send to myself. I just can't seem to get it all put together. I've been trying to use ConvertTo-Html but it just seems to return data via email like "pageFooterEntry" and "Microsoft.PowerShell.Commands.Internal.Format.AutosizeInfo" versus the actual data. I can get it to send me the right data if i don't tell it to ConvertTo-Html, just have it pipe the data to a text file and pull from it, but it's all ran together with no formatting. I don't need to save the file, i'd just like to run the command, get the data, put it in HTML and mail it to myself. Here's what I have currently: #Connects to Database and returns information on all users, organized by Total Item Size, User $body = Get-MailboxStatistics -database "Mailbox Database 0846468905" | where {$_.ObjectClass -eq “Mailbox”} | Sort-Object TotalItemSize -Descending | ft @{label=”User”;expression={$_.DisplayName}},@{label=”Total Size (MB)”;expression={$_.TotalItemSize.Value.ToMB()}} -auto | ConvertTo-Html #Pause for 5 seconds for Exchange write-host -foregroundcolor Green "Pausing for 5 seconds for Exchange" Start-Sleep -s 5 $toemail = "[email protected]" # Emails report to this address. $fromemail = "[email protected]" #Emails from this address. $server = "Exchange.company.com" #Exchange server - SMTP. #Email the report. $email = New-Object System.Net.Mail.MailMessage $email.IsBodyHtml = $True $email.To.Add($toemail) $email.From = $fromemail $email.Subject = "Exchange Mailbox Sizes" $email.Body = $body $client = New-Object System.Net.Mail.SmtpClient $server $client.UseDefaultCredentials = $true $client.Send($email) Any thoughts would be helpful, thanks!

    Read the article

< Previous Page | 228 229 230 231 232 233 234 235 236 237 238 239  | Next Page >