Search Results

Search found 80052 results on 3203 pages for 'data load performance'.

Page 234/3203 | < Previous Page | 230 231 232 233 234 235 236 237 238 239 240 241  | Next Page >

• SAS Array with or without expander

  - by tegbains

  Is it better to use a SAS Expander backplane for 12 drives via one SAS connection or is it better to use a SAS backplane with 3 SAS connections? This is in terms of performance, rather than expansion. This array will be setup using ZFS on a OpenSolaris via a LSI SAS controller as an iSCSI target. The two products being considered are the SuperMicro SuperChassis 826A-R1200LPB or the SuperChassis 826E2-R800LPB

  Read the article

• Vista failing to load after apparently being repaired

  - by Joomaz

  Hi, I apologise if I'm a litre vague and can give more info if needed. My vista machine has been working fine until today when I tried booting it. Vista loads showing the loading bar then goes to a black screen with the cursor on which you can move. It then remains like this for several minutes, during this time the computer doesn't sound like it's doing much, it is relatively quiet. Finally the welcome screen appears. It stays on this for several minutes again and the computer reboots. This keeps happening and the machine fails to load in safe mode - the same happens. I booted the pc with the vista disk in and ran repair your computer and used the system repair. It took about 20 minutes saying it was repairing damaged giles. I booted the pc again and the same happened. I loaded the pc with yeh vista disk again and chose repair my computer again. System repair seemed to run automatically this time and agian it did the same. I rebooted and the problem persisted. I then tried system restore to a few days ago. After half a hour as it finished it said it failed due to a portion being corrupt. I am really not sure what to do now. Any advice appreciated!

  Read the article

• Can't get an IBM xSeries 345 server to load Windows Server 2003 using ServerGuide utility

  - by Kyle Noland

  I have a client that has an IBM xSeries 345 eServer. Per the IBM support website, I have downloaded the ServerGuide Setup 7.4.17 installation ISO and burned a bootable CD. The CD boots fine and loads the utility. I walk through the following screens without any issue: Set the date and Time Detect the IBM ServeRAID card and install the latest firmware Clear the hard disks Set up the RAID array The next step is format the NOS partition. I select my partition size and the utility goes through the following steps: Creating NOS partition Formatting NOS partition (NTFS) Copying W32 files The copying W32 files takes about 10 minutes. I see the CD drive and disks working hard. When the copying is complete, I'm taken to a blank page just NOS Partitioning at the top. At the bottom of the screen are the familiar Back and Exit buttons. I see the place where the Next button should be, and if I click on it I can tell there is something there, but the space is empty. No button is displayed and clicking the empty spot doesn't ever take me to the next screen. I can't load the OS until I get past this part. I have already tried: Burning multiple copies and versions of the ServerGuide CD Letting the final screen just sit there over the weekend thinking it might advance after syncing the drives or something Has anybody else seen this? I'm really at a loss here.

  Read the article

• Speed of TrueCrypt whole disk encryption

  - by Gareth

  I'm getting a new development laptop soon, and I'm thinking of using TrueCrypt to encrypt the whole disk. What kind of performance drop can I expect? 10%? 30%? more? Also, assuming the workload has an effect, would compiling/using Visual Studio be affected much? I cannot seem to find anything like this on the web.

  Read the article

• Apache start failing after apache config modifications, showing syntax error, cannot load php5apache2_2.dll into server

  - by Sandeepan Nath

  I am stuck again with apache setup guys. I am working on a Windows 7 system. I copied the working php5 installation directory from teammates, copied the necessary .dll files from inside php5 installation folder (like they were in the working setup of teammates) to my windows/system32/. Apache server started successfully with the default apache config file. I was able to access localhost in browser. But php code was not parsing. I noticed no such line like the following in the apache config file:- # PHP5 module LoadModule php5_module D:/php5/php5apache2_2.dll If I add this line, apache server start fails. Running test configuration gives the following error - httpd.exe: Syntax error on line 60 of C:/Program Files (x86)/Apache Software Foundation/Apache2.2/conf/httpd.conf: Cannot load D:/php5/php5apache2_2.dll into server: The specified procedure could not be found. But the dll file is there in the specified location and I have given all permissions to the current system user to the php5 installation directory. The same line also appears in the apache error log, though I am not sure when exactly logs are written to the log file. I am confused if log entries are not made if I have opened the log file for reading? lol ... because I could not observe a pattern in when entries are made. I saw some log entries being made, some not. Oh, why is apache setup such a headache always????

  Read the article

• IIS6 intranet site using integrated authentication fails to load when accessed externally

  - by maik

  I've developed a couple of internal sites for my organization that use integrated authentication. Ultimately we want these sites to be accessible externally to users with domain-joined computers. The sites work as expected on domain computers while on the internal network. The problem comes when I take my laptop home and try to access those sites. IIS only has integrated authentication enabled for the two sites. When I browse to the site using IE8 I get a username/password prompt asking for domain credentials. I can put those in and it will work, but the goal is to use the cached token for integrated authentication. Next I reasoned that IE wouldn't response to an integrated auth request (is NTLM the right term for this?) unless the site was trusted. I tried adding the site to Trusted Sites but I get the same behavior as the before. I then added the site to Local Intranet sites and that is where things get weird. I get a generic error page from IE, no error code or anything. Just for funsies I loaded up Firefox (which I had previously set up to use integrated authentication) and I added this new site to network.automatic-ntlm-auth.trusted-uris. Much to my surprise I was able to load the pages up with no problem at all and saw exactly what I was expecting (including verification that the integrated authentication worked). My mind is a bit boggled at the moment as I'm not really sure where to go from here. I was hoping some of you may be able to provide some insight.

  Read the article

• Any reason not to disable Windows kernel paging?

  - by Nathaniel

  So I'm planning on eventually going to 2 GB (mobo max) RAM from 1 GB, and I want to disable kernel paging once I do, because I've heard it can give a performance boost (and that I believe). Any reason not to do it or any general thoughts about it? Edit: for clarification, this is not disabling general RAM paging. This is disabling having kernel memory paged (or at least parts of it, as Charlls noted).

  Read the article

• Ways to go about optimizing website performance WordPress, Amazon EC2 Apache and RDS MySQL

  - by fuzzybee

  I have 6 WordPress websites running on 1 single EC2 instance. All the the websites are connecting to databases in 1 same RDS instance. Earlier today, traffic to the largest website peaked and the RDS instance went bottle-neck - CPU utilization was 100% for over an hour. It affected all of my websites as it took them all forever to load. In order to prevent such issue from happening again, which of the following will matter most so that I invest time and effort in first of all? (I will work on all later, I just need to prioritise now) To improve caching for all websites To fine-tune the database server To fine-tune my Apache server What will be the effect on user experience for my websites? Some quick searches show that I should limit number of concurrent connections to my web server but wouldn't that prevent users from accessing my websites? More background: My largest website has 140k visits and 660k page views a month. The other 5 websites should add up much less than that. I'm using a large EC2 instance as the web server I'm using a medium RDS instance as the database server What I've already done: Use W3 Total Cache plugin for caching for most the websites, especially the largest one (I can barely anything else in terms of caching I could do for the largest website) Am I using my resources wastefully or is there simply not enough resources for my websites - or rather, how do I answer that question myself?

  Read the article

• ApacheBench result to a file

  - by Tomaszs

  I would like to save ApacheBench (ab) tool on linux to a file. When I run it with -v 2 it displays some results in my ssh window. How to move these data into a file and make sure that it will not display on ssh no more? I've tried file.txt 2&1 but it does not work and still display data in my ssh window. I use: ab -n 10000 -c 200 http://mywebsite.com > file.txt 2>&1

  Read the article

• Getting Windows (VMware) to load from OSX's localhost without an Internet Connection

  - by Jonah Goldstein

  I'm using MAMP to host my local sites, and VirtualHostX so that I can access sites during local development via a convenient URL like mysite.dev I'm also running Windows XP via VirtualBox, and it would be great to be able to load up any of my local sites within windows while offline as currently often working without access, on the move, unfortunately. I know that I can append my IP and a nice domain name to the host file in C:/WINDOWS/system32/drivers/etc ... and i can find my IP simply through terminal with "ifconfig" while I'm online. The problem is that when I'm not online, there's no IP. Even if there is an IP (when i have a connection), I still have grab it and update the windows hosts' file all the time, since I'm developing from a laptop and have a new IP at the drop of a dime. I found a tutorial where the author is able to get a permanent IP. He uses VMware Fusion as his VMachine, which is the only difference between his setup and mine. By running the terminal command "ifconfig vmnet1" he gets: a secret IP the virtual machine uses to talk to OSX And that doesn't change - which is awesome. I'm assuming it exists even if he's offline. His tutorial is here, http://bit.ly/U2lq It would be pretty fantabulous if I could replicate this with virtualBox. Anyone have ideas? Thanks:)

  Read the article

• How to monitor the total number of SQL Server logins

  - by Shiraz Bhaiji

  We have an SQL Server 2005 that is the backend of a web application. The application is partly SharePoint and partly web services accessing the database via Entity Framework. In the performance monitor I am seeing average SQL Logins is ca, 60 per second (max 170), but the average logouts is less than 1. Where can I see the total number of SQL Server logins? Anyone have an idea what could be causing this?

  Read the article

• PPP kernel module fails to load

  - by Harel

  I am trying to deal with a problem on a server I don't normally deal with. Out of the blue a script using ppp started failing saying that the ppp kernel module is not loaded. When I try to modprobe it it complains about files missing. Note below that the kernel version the server thinks it at, does not match the kernel version directory in /lib/modules. I'm not sure how this could have happened. Could the other maintainers of the server botched a kernel upgrade? My question is how can I fix this discrepancy. Can I simply rename the lib directory and hope for the best? I don't want to break stuff for the people who actually maintain the server but I do need to fix the PPP issue. $ sudo /sbin/modprobe -v ppp FATAL: Could not load /lib/modules/2.6.35.4-rscloud/modules.dep: No such file or directory $ cat /proc/version Linux version 2.6.35.4-rscloud ([email protected]) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) ) #8 SMP Mon Sep 20 15:54:33 UTC 2010 $ ls /lib/modules/ 2.6.33.5-rscloud

  Read the article

• Looking for CDN Comparison

  - by David Andersson

  I can't seem to find a good performance comparison of different CDN services, like CloudFront, Limelight etc. Anyone's got a good link?

  Read the article

• Why are there many processes listed under the same title in htop?

  - by javanix

  Can anyone explain to me why there are sometimes 10 or 15 processes with the same title and "stats" listed in htop? I'm guessing there are multiple threads running - but that many of them obviously couldn't be running concurrently. Is there any sort of performance hit taken if a process uses say, 15 non-concurrent threads vs. 10 non-concurrent threads?

  Read the article

• Why is my new Phenom II 965 BE not significantly faster than my old Athlon 64 X2 4600+?

  - by Software Monkey

  I recently rebuilt my 5 year old computer. I upgraded all core components, in particular from an Athlon 64 X2 4600+ at 2.4 GHz with DDR2 800 to a Phenom II 965 BE (quad core) at 3.6 GHz with DDR3 1333 (actually 1600, but testing consistently detected memory errors at 1600). The motherboard is also much newer and better. The HDD's (x3), DVD writer and card reader are the same. The BIOS memory config is auto-everything except the base timing which I overrode to 1T instead of 2T. The BIOS CPU multiplier is slightly over-clocked to 3.6 GHz from the stock 3.4 GHz. I noticed compiling Java is slower than I expected. As it happens I have some (single-threaded) Java pattern-matching code which is CPU and memory bound and for which I have performance numbers recorded on a number of hardware platforms, including my old system. So I did a test run on the new equipment and was stunned to find that the numbers are only slightly better than my old system, about 25%. The data set it is operating on is a 148,975 character array, which should easily fit in caches, but in any event the new CPU has larger caches all around. The system was, of course, otherwise idle for the test and the test run is a timed 10 seconds to eliminate scheduling anomalies. A long while ago, when I upgraded only memory from DD2 667 to DDR2 800 there was no change in performance of this test, which subjectively supports that the test cycle does not need to (significantly) access main memory, but yes it is creating and garbage collecting a large number of objects in the process of this test (low millions of matches are found for the pattern set). I am about 99.999% certain the code hasn't changed since I last ran it on 2009-03-17 - but I can't easily retest the old hardware, because it is currently in pieces on my work-bench waiting to be built into a new computer for my kids. Note that Windows (XP) reports a CPU speed of 795 MHz unless I have some thing running. With stuff running it seems to jump all over the place each time I use ALT-Pause to display the system properties, everywhere from 795 MHz to 3.4 Ghz. So why might my shiny new hardware under-performing so badly? EDIT: The old memory was Mushkin DDR2 800 with timings set for auto which should have been 5-5-5-12. The new memory is Corsair DDR3 1600, running at 1333 with timings also auto which are 9-9-9-21. In both cases they are a paired set of dual channel DIMMs. I was waiting to ensure my system was stable before tweaking with memory timings.

  Read the article

• HAproxy with MySQL Master-Master Replication incredibly slow

  - by Yayap

  I have two MySQL servers in multi-master mode, with an HAproxy machine for simple load balancing/redundancy. When I am connected to one of the servers directly and try to update about 100,000 entries, it is completed including replication in about half a minute. When connecting through the proxy it takes usually over three whole minutes. Is it normal to have that type of latency? Is something amiss with my proxy configuration (included below)? This is getting really frustrating as I assumed the proxy would do some sort of load balancing, or at least have little to no overhead. #--------------------------------------------------------------------- # Example configuration for a possible web application. See the # full configuration options online. # # http://haproxy.1wt.eu/download/1.4/doc/configuration.txt # #--------------------------------------------------------------------- #--------------------------------------------------------------------- # Global settings #--------------------------------------------------------------------- global # to have these messages end up in /var/log/haproxy.log you will # need to: # # 1) configure syslog to accept network log events. This is done # by adding the '-r' option to the SYSLOGD_OPTIONS in # /etc/sysconfig/syslog # # 2) configure local2 events to go to the /var/log/haproxy.log # file. A line like the following can be added to # /etc/sysconfig/syslog # # local2.* /var/log/haproxy.log # log 127.0.0.1 local2 # chroot /var/lib/haproxy # pidfile /var/run/haproxy.pid maxconn 4096 user haproxy group haproxy daemon #debug #quiet # turn on stats unix socket stats socket /var/lib/haproxy/stats #--------------------------------------------------------------------- # common defaults that all the 'listen' and 'backend' sections will # use if not designated in their block #--------------------------------------------------------------------- defaults mode tcp log global #option tcplog option dontlognull option tcp-smart-accept option tcp-smart-connect #option http-server-close #option forwardfor except 127.0.0.0/8 #option redispatch retries 3 #timeout http-request 10s #timeout queue 1m timeout connect 400 timeout client 500 timeout server 300 #timeout http-keep-alive 10s #timeout check 10s maxconn 2000 listen mysql-cluster 0.0.0.0:3306 mode tcp balance roundrobin option tcpka option httpchk server db01 192.168.15.118:3306 weight 1 inter 1s rise 1 fall 1 server db02 192.168.15.119:3306 weight 1 inter 1s rise 1 fall 1

  Read the article

• Web Service gets unavailable after several concurrent calls

  - by Roman

  We are testing GoDaddy Virtual Data Center and came to a very strange issue when our web site gets unavailable. GoDaddy Support keeps saying the issue is in our web server settings, but looking at the result of our tests I doubt it. TEST ENVIRONMENT Virtual DataCenter with Windows hosted at GoDaddy.com. All servers have Windows Server 2008 R2 Datacenter, IIS 7. Server One with IP address 10.1.0.4 Server Two with IP address 10.1.0.3 Both servers are in private network not visible from outside. Port Forward with IP address 50.62.13.174. Port Forward is assigned to Server One TEST DESCRIPTION JMeter is used as a Client App to simulate 30 concurrent users sending 100 SOAP requests each. Interval between requests is 1 second. Http link used for testing: http://50.62.13.174/v2/webservices.asmx TEST ONE Test is run from a computer in our office. After JMeter starts running test, almost immediately, the link above becomes unavailable in a browser. After test completion, the link is not available in a browser for about 5 more minutes. Remote Desktop is working well, so we can connect to Server One remotely. After about 5 minutes since test completion, the link becomes available in a browser again. TEST TWO Test is run from Server Two (that is part of our virtual data center). Test works very well, no visible delays in processing. The link is available in a browser all the time. TEST THREE Test is run from Server One using localhost. The result is the same as in TEST TWO - no issues. TEST FOUR We repeated TEST ONE from other computers that we have located in different countries, all with the same result as TEST ONE. CONCLUSION As the test works well from Server Two, but does not work from outside our virtual data center, we feel there are issues with the network or its capacity. The whole behaviour looks like out requests from outside get stuck somewhere before reaching our virtual data center. Has anybody had similar issues in the past? Are there chances that something is wrong with our server settings?

  Read the article

• No architecture vs architecture-specific binaries

  - by Aaron

  From what I understand, the noarch suffix means that it's architecture independent and should work universally. If this is the case, why should I install architecture-specific packages at all? Why not just go straight for the noarch? Are there optimizations in the x86 or x64 binaries that aren't found in the noarch binaries? What's best for high performance applications? Folding@Home does this with their controller:

  Read the article

• Testing realistic loads for new versions of existing web app

  - by David Cournapeau

  Assuming I have a relatively complex web application, I am interested in testing performances of a new version using a traffic as realistic as possible. Traffic is relatively complex (session-based, lots of internal logic which depends on incoming requests). The webapp depends on many servers (databases, frontends, etc...). I can think of two basic directions: Recording every incoming request with its timestamp in production in a centralized manner and replaying it from N clients to reproduce a load as close as possible as the original. Issue: because we have many servers, getting the centralized log is not trivial. having a system duplicating requests to a staging area so that I could "plug" a dev version of my webapp to it at anytime without affecting the production. Issue: I have not found much information about it expect this, which suggests to me that may not be the best solution. OTOH, it is realistic by definition. What is the standard way of doing this kind of testing ? I did not find much information about load testing with complex, realistic traffic.

  Read the article

• Hiera datatypes wont load in Puppet

  - by Cole Shores

  I have spent a couple of days on this, followed the instructions on http://downloads.puppetlabs.com/docs/puppetmanual.pdf and even the Puppet Training Advanced Puppet manual. When I run a test against it, the results always come back as 'nil' and Im not sure why. I am running Puppet 3.6.1 Community Edition, with Hiera 1.2.1 on SLES 11. My puppet.conf file at /etc/puppet/puppet.conf consists of: [main] # The Puppet log directory. # The default value is '$vardir/log'. logdir = /var/log/puppet # Where Puppet PID files are kept. # The default value is '$vardir/run'. rundir = /var/run/puppet # Where SSL certificates are kept. # The default value is '$confdir/ssl'. ssldir = $vardir/ssl certificate_revocation = false [master] hiera_config=/etc/puppet/hiera.yaml reporturl = http://puppet2.vvmedia.com/reports/upload ssl_client_header = SSL_CLIENT_S_DN ssl_client_verify_header = SSL_CLIENT_VERIFY # certname = dev-puppetmaster2.vvmedia.com # ca_name = 'dev-puppetmaster2.vvmedia.com' # facts_terminus = rest # inventory_server = localhost # ca = false [agent] # The file in which puppetd stores a list of the classes # associated with the retrieved configuratiion. Can be loaded in # the separate ``puppet`` executable using the ``--loadclasses`` # option. # The default value is '$confdir/classes.txt'. classfile = $vardir/classes.txt # Where puppetd caches the local configuration. An # extension indicating the cache format is added automatically. # The default value is '$confdir/localconfig'. localconfig = $vardir/localconfig my /etc/puppet/hiera.yaml consists of: :backends: yaml :yaml: :datadir: /etc/puppet/hieradata :hierarchy: - common - database I have a directory created in /etc/puppet/hieradata and within it contains: /etc/puppet/hieradata/common.yaml :nameserver: ["dnsserverfoo1", "dnsserverfoo2"] :smtp_server: relay.internalfoo.com :syslog_server: syslogfoo.com :logstash_shipper: logstashfoo.com :syslog_backup_nfs: nfsfoo:/vol/logs :auth_method: ldap :manage_root: true and /etc/puppet/hieradata/database.yaml :enable_graphital: true :mysql_server_package: MySQL-server :mysql_client_package: MySQL-client :allowed_groups_login: extranet_users does anyone have any idea what could be causing Hiera to not load the requested values? I have tried even restarting the Master. Thanks in advance, Cole

  Read the article

• Nginx + PHP-FPM Timeouts, almost zero load consumption?

  - by javipas

  I've got a server running on a Linode with Ubuntu 10.04 LTS, Nginx 0.7.65, MySQL 5.1.41 and PHP 5.3.2 with PHP-FPM. There is a WordPress blog on it, updated to WordPress 3.2.1 recently. I have made no changes to the server (except updating WordPress) and while it was running fine, a couple of days ago I started having downtimes. I tried to solve the problem, and checking the error_log I saw many timeouts and messages that seemed to be related to timeouts. The server is currently logging this kind of errors: 2011/07/14 10:37:35 [warn] 2539#0: *104 an upstream response is buffered to a temporary file /var/lib/nginx/fastcgi/2/00/0000000002 while reading upstream, client: 217.12.16.51, server: www.mydomain.com, request: "GET /page/2/ HTTP/1.0", upstream: "fastcgi://127.0.0.1:9000", host: "www.mydomain.com", referrer: "http://www.mydomain.com/" 2011/07/14 10:40:24 [error] 2539#0: *231 upstream timed out (110: Connection timed out) while reading response header from upstream, client: 46.24.245.181, server: www.mydomain.com, request: "GET / HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "www.mydomain.com", referrer: "http://www.google.es/search?sourceid=chrome&ie=UTF-8&q=mydomain" and even saw this previous serverfault discussion with a possible solution: to edit /etc/php/etc/php-fpm.conf and change request_terminate_timeout=30s instead of ;request_terminate_timeout= 0 The server worked for some hours, and then broke again. I edited the file again to leave it as it was, and restarted again php-fpm (service php-fpm restart) but no luck: the server worked for a few minutes and back to the problem over and over. The strange thing is, although the services are running, htop shows there is no CPU load (see image) and I really don't know how to solve the problem. The config files are on pastebin The php-fpm.conf file is here The /etc/nginx/nginx.conf is here The /etc/nginx/sites-available/www.mydomain.com is here Please help :(

  Read the article

• how to go about scaling a web-application ?

  - by phoenix24

  for someone whoes been primarily a web-application developer, and know not much about scaling/scalability techniques. I'll start by stating my application is written in Python, using Django; a fairly standard setup. I currently use Apache 2.2 for my webserver, and MySql for my database server; both running on the same vps server. Up until now, it was basically a prototype and merely 15-30 concurrent users at any given time; so I had no issues, but now since we'll be adding more users we'll have severe performance issues. So my question is how do i go about scaling my web-application? and my plan is as follows. Now I have just one vps server running, apache + mysql. Next, I plan to add another vps server, to run only MySql; so i'll have one web-server and one db server. Next, I'll add Memcache to the webserver for caching data; and taking some load off mysql. Next, another web-server for serving all the static content; Next, a vps server for load-balancing (nginx/varnish) behind which would be my two web-servers and then db-server. Does that sound like a workable strategy, please guide me around here.

  Read the article

• Cannot load from raid with grub

  - by Andrew Answer

  I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... This is my partial fdisk -l output: Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Anybody can resolve this issue? I have big headache with this.

  Read the article

• How to clear Windows disk read cache?

  - by Sebastiaan Megens

  For performance testing I need to clear Windows' disk read cache. I tried googling but I couldn't find anything other than rebooting or other manual stuff. Before I give in and do that, I'd like to know if anyone knows of a way to clear Windows disk read cache. I'm testing on Windows 7, but I'm also interested in Windows XP solutions.

  Read the article

• What is good usage scenario for Rackspace Cloud Files CDN (powered by AKAMAI) [closed]

  - by Andrew Smith

  I have just setup my website as static page via Rackspace CDN / Akamai. www.example.co.uk is an alias for d9771e6f24423091aebc-345678991111238fabcdef6114258d0e1.r61.cf3.rackcdn.com. d9771e6f24423091aebc-345678991111238fabcdef6114258d0e1.r61.cf3.rackcdn.com is an alias for a61.rackcdn.com. a61.rackcdn.com is an alias for a61.rackcdn.com.mdc.edgesuite.net. a61.rackcdn.com.mdc.edgesuite.net is an alias for a63.dscg10.akamai.net. a63.dscg10.akamai.net has address 63.166.98.41 a63.dscg10.akamai.net has address 63.166.98.40 a63.dscg10.akamai.net has IPv6 address 2001:428:4c02::cda8:ecb9 a63.dscg10.akamai.net has IPv6 address 2001:428:4c02::cda8:ed09 The HTTP header: HTTP/1.0 200 OK Last-Modified: Fri, 19 Oct 2012 23:27:41 GMT ETag: fdf9e14b77def799e09e8ce815a521da X-Timestamp: 1350689261.23382 Content-Type: text/html X-Trans-Id: tx457979be3bd746c2b4e5403a1189cdbc Cache-Control: public, max-age=900 Expires: Sat, 27 Oct 2012 22:18:56 GMT Date: Sat, 27 Oct 2012 22:03:56 GMT Content-Length: 7124 Connection: keep-alive I am wondering, if it's really the fastest solution to power the website? By investigating it thru http://www.just-ping.com/ it seems, that from many places the ping is very high, and during quick investigation I found that they use GeoIP to resolve addresses based on WHOIS, which is not accurate and because of that from many places the ping is above 300ms (for example, if ISP is in balgladore and request is routed to bangladore even if it's 300ms, for period of 1 month), while by just using Amazon Web Services and Route 53 Anycast DNS servers and only 4 EC2 instances it seems that for example India is always below 100ms, while using Akamai it goes above 300ms in some cases, and this is because Route 53 is using BGP. By quickly checking the Akamai, it seems that they are not getting feedback from the traffic - the high ping stays constant even if I keep downloading large files and videos, which is opposite to what they say on their website. They state, that they optimize the performance by taking feedback from the requests, while it seems they just use GeoIP with per City resolution (which are mostly big cities). Because of this, AWS with Route 53 / Anycast DNS seems to be much more reliable, as well EdgeCast which is using BGP, but I dont know how much does it cost to deploy static website. Actually, I dont know if EdgeCast is not a lie, because from isolated places there are many errors - so their performance is at the cost of quality of delivery, because of BGP switching the routes during transfer of large files. So I was wondering, what is really Akamai good for, because they dont seem to pose any strength in any field in what I do understand now, except they offer some software based WAF on their website, but what I really care about is the core distribiution, so the question is? Is really Akamai good for Videos? For static websites? ??? I found so far AWS most usable with most consistent ping and stable transfers.

  Read the article

< Previous Page | 230 231 232 233 234 235 236 237 238 239 240 241  | Next Page >