Search Results

Search found 19557 results on 783 pages for 'networking programming'.

Page 238/783 | < Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >

• RESOLVED Why does IPtables's NAT stop working when I enable the firewall's third interface?

  - by Kronick

  On my firewall I've three interfaces : eth0 : public IP (46.X.X.X.) eth0:0 public IP (46.X.X.Y.) eth1 : public IP (88.X.X.X.) eth2 : private LAN (172.X.X.X) I've setup a basic NAT which works great until I turn on the eth1 interface, I basically loose the connectivity. When I turn off the interface (ifconfig eth1 down) then the NAT re-work. I've added some policy routing via iproute, which makes my three public IP's available. I don't understand why turning on eth1 on makes the LAN unavailable. PS : weirder ; when I turn on eth1 BUT remove the NAT, then the firewall is accessible by using the public IPS. So to me it's exclusively a NAT issue, since without the NAT the network works while with the NAT without the second public interface, the NAT does work. Regards EDIT : I've been able to make it work by using iproute2 rules. That was definitely a routing issue. Here is what I did : ip rule add prio 50 table main ip rule add prio 201 from ip1/netmask table 201 ip rule add prio 202 from ip2/netmask table 202 ip route add default via gateway1 dev interface1 src ip1 proto static table 201 ip route append prohibit default table 201 metric 1 proto static ip route add default via gateway2 dev interface2 src ip2 proto static table 202 ip route append prohibit default table 202 metric 1 proto static # mutipath ip rule add prio 221 table 221 ip route add default table 221 proto static \ nexthop via gateway1 dev interface1 weight 2\ nexthop via gateway2 dev interface2 weight 3

  Read the article

• solving network connection problem on xp

  - by doug

  Hi there I feel so stupid, because I have to fix my dad computer(which was mine years ago). So it is an old computer on which I have installed windows xp and the drivers for main-board. The device manager says that I have no more problems with the hardware. That computer has to connect to a router from my room but it doesn't. On ping 192.168.2.1 I get "Request time out"., The other computers are connecting to that router. Only the old computer doesn't connect to the LAN and later to the internet. Also it doesn't get a good IP(from the same class). After running ipconfig command I know that i have an IP with 169.... What can I do? Do you have any tips for me?

  Read the article

• How can I start hostednetwork on Windows 7?

  - by Pirozek

  When I type in admin console command to start hostednetwork netsh wlan start hostednetwork it gives me this: The hosted network couldn't be started. The group or resource is not in the correct state to perform the requested operation. There is a hotfix from Microsoft but it didn't help me. Any advice? C:\Users\Pirozek>netsh wlan show driver Interface name: Wireless Network Connection 3 Driver : D-Link AirPlus DWL-G520 Wireless PCI Adapter(rev .B) Vendor : Atheros Communications Inc. Provider : Atheros Communications Inc. Date : 8.7.2009 Version : 8.0.0.171 INF file : C:\Windows\INF\oem108.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g FIPS 140-2 mode supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Shared WEP-40bit Open WEP-104bit Shared WEP-104bit Open WEP Shared WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP

  Read the article

• WinXP workgroup, 3 routers 3 computers

  - by Silvera

  I have 3 computers with WinXP x86, and 3 Cisco 1800 series routers. I'm trying to create a workgroup so that the 3 computers can share files with eachother. They can ping eachother (without any internet connection), and the routers setup is correctly configured (with interfaces, ip adresses, and ports). But none of the computers can see eachother, even though they are on the same network. My first question would be - can it be done the way it is currently configured - and, if yes, how, or can anyone point me in the right direction?

  Read the article

• Troubleshooting my internet connection

  - by Simon Verbeke

  While I was out of the house, my father rearranged the network cables a bit. I don't know what he has done exactly - He says nothing more then pulling and untangling. When I came back home, my internet connection changed its IP from 192.168.0.205 to 169.254.197.233. The speed changed from 1Gbps to 10Mbps. It has also been at 100Mbps for a while. My subnetmask changed from 255.255.255.0 to 255.255.0.0. The standard gateway changed from 192.168.0.1 to no standard gateway. My DNS servers remain the same. I have checked the lights of the UTP ports, and it looks like it's only sending a heartbeat every few seconds. A sketch of the (relevant part of) the network: My PC ----- extender ----- modem ^ ^ ^ Wired | Wired | This thing connects two cables to each other All the cabling is gigabit, my network card is a Realtek RTL8168C(P)/8111(P) Family PCI-E Gigabit Ethernet NIC (NDIS 6.20). THe modem is a CBN SVG6540E I have no idea what is going on here and I don't know how to find out either. Any help is welcome! If you need any more info, please ask.

  Read the article

• Conflicting ip routes with local table on attaching a virtual network interface

  - by user1071840

  I have an EC2 instance with these ip rules: $ sudo ip rule show 0: from all lookup local 32766: from all lookup main 32767: from all lookup default I can attach an elastic network interface to it with a private IP. Say the IP of my machine is 10.1.3.12 and the IP of the interface is 10.1.1.190. As soon as I attach the interface to my machine a new entry is added to the routing policy and local routing table: sudo ip rule show 0: from all lookup local 32765: from 10.1.1.190 lookup 10003 32766: from all lookup main 32767: from all lookup default $ sudo ip route show table local broadcast 10.1.1.0 dev eth3 proto kernel scope link src 10.1.1.190 local 10.1.1.190 dev eth3 proto kernel scope host src 10.1.1.190 broadcast 10.1.1.255 dev eth3 proto kernel scope link src 10.1.1.190 broadcast 10.1.3.0 dev eth0 proto kernel scope link src 10.1.3.12 local 10.1.3.12 dev eth0 proto kernel scope host src 10.1.3.12 broadcast 10.1.3.255 dev eth0 proto kernel scope link src 10.1.3.12 broadcast 127.0.0.0 dev lo proto kernel scope link src 127.0.0.1 local 127.0.0.0/8 dev lo proto kernel scope host src 127.0.0.1 local 127.0.0.1 dev lo proto kernel scope host src 127.0.0.1 broadcast 127.255.255.255 dev lo proto kernel scope link src 127.0.0.1 I can send traffic to this ENI directly from a host that can have the same IP as the host the ENI is attached to. This is where the problem starts. I ran tcpdump on the port in question and saw multiple SYNs going to the ENI with src '10.1.3.12' and destination '10.1.1.190' but didn't see even a single ACK. In my understanding if ACKs were being sent from the ENI they'd have destination as 10.1.3.12 i.e. the same as the local machine's IP and such packets will now be routed as local packets matching local routing policy: local 10.1.3.12 dev eth0 proto kernel scope host src 10.1.3.12 I'd like to send all the packets originating from 10.1.1.190 (my ENI) to go back on the same interface i.e. eth3 in this case. Contents of the nee table 10003 are: $ sudo ip route show table 10003 default via 10.1.1.1 dev eth3 I think I can do the following: I don't know if its possible but probably decrease the priority of local table so the packets match the table 10003. Use iptables to mangle these packets and update the local table route to include the mark information But I'm not sure if these are the right approaches.

  Read the article

• Jumbo Frames on DIR-655

  - by Spookyone

  I am trying to set up jumbo frames on my gigabit home LAN but no luck so far. My setup is: D-Link DIR-655 router, HW Revision A3, Firmware 1.21 EU Synology DS107+, Firmware 3.0-1337 Laptop w/ Win7 x64, external PCIx NIC managed by "Generic Marvel Yukon 88E8053 based Ethernet Controller" The router is supposed to support jumbo frames but doesn't feature any relevant setting. I set the Jumbo Packet value to 9000 on both the NIC and the Synobox but it doesn't work, ping -f -l 8972 says "Packet needs to be fragmented but DF set". Is there any other setting I overlooked, the DIR-655 doesn't actually support jumbo frames, or what else could be the problem?

  Read the article

• Share PC over network

  - by Sachin Verma

  I have a server installed on one local Win7 machine (say as 192.168.2.14:8080/myAPP) and I want to access that server from different computer (say ip as 192.168.2.16). Even they are connected to same network I can't access server from other computer. I guess the problem is in firewall. This is working when I disable firewall and not working when I allow certain ports in windows firewall but keeping firewall on (As a rule to allow incoming connections).

  Read the article

• Window 7 image in vmware will allow network connection out but not http

  - by Ormis

  I am currently trying to create a set of images to deploy on my network, but I've run in to a snag. When I create my own Windows 7 image I can successfully use NAT for connecting to the network but whenever I try to access a webpage I get nothing. To be more specific, All firewalls/iptables are disabled on my host machine, my virtual machine, and my network. I can do lookups and all addresses respond correctly (i'm even using Google's DNS). On the host OS i have full connectivity. On the virtual machine I can ping any device I want and all addresses resolve correctly. Within a browser I cannot reach any page via hostname or IP. I feel almost like port 80 is being blocked but i can't find any reason this would be the case. If anyone has had this occur before, I would love some insight to the problem. I initially asked this on stackoverflow and now my eyes are now opened up to superuser. Thank you for any help you can provide.

  Read the article

• map linux drives to windwos 7 for media stream over internet

  - by Ortix92

  I'm trying to map a linux network drive to my windows 7 laptop, however this laptop is not on LAN. At home, I simply use Samba, but this obviously won't work over the internet. I'm trying to avoid VPN, so if there are other solutions, I would like to know about them. The reason I ask is because my university does this as well. We can simply map folders to our computers without VPN connections. I'm not sure what they are running as servers. The main reason is because I want to be able to access my files stored on my home server wherever I go. They are located in the /home/ folder (videos, music and pictures folder). I'm trying to keep my websites and media separate from each other. I wouldn't mind accessing them from a web interface either, but I would like to keep the directory structure intact. I remember having an app like that come with winamp and running it on my windows pc (As the server). Unfortunately it doesn't work for linux. Any ideas on what I could use? Would XBMC be able to help me out with this? I did do some researching but I couldn't find any concrete answers

  Read the article

• WAN Optimization for Small Office/Home Office

  - by TiernanO

  I have been reading up on WAN optimization for the last while, mostly out of interest of speeding up my own internet connections, but also to speed up the office internet connection. At home, I have 2 cable modems plugged into a RouterBoard RB750, which load balances the connections. In the office, we have a single connection into a NetGear router. Most of the WAN Optimization products I have seen, seem to be prohibitively expensive, but also seem to be based on the idea of having multiple branches around the world. What I am looking for, ideally, is as follows: software install: I am "guessing" I need to install it in 2 places: one in the office or house, and one in "the cloud". any connections going to, say, The US (we are in Europe, but our backup's live in the US currently, which would be something important to speed up) would be "tunnelled" though the Optimizer. If downloading or uploading large files, open multiple connections between both "the cloud" and the optimizer... This is where a lot of speed could be gained. finally, for items not compressed, they would be compressed on the cloud side of things, also items that are already on the optimizer could be not sent again. kind of like RSync or Proxy servers... So, is there something that can be done? Is it available using off the shelf components (some magic script with SSH, Squid, Linux and duct tape) or is it something that needs to be purchased? or even an Open Source Project that does 90% of what i am asking?

  Read the article

• Mount linux partition as Windows network share over internet

  - by CptEO

  I have a Linux server running RHEL 6. I have two Windows servers. All servers are connected directly to the web with an external IP, they are not in a local lan. What I would like to achieve is to setup the Linux server so that it offers a single share (the whole partition) that can be mounted as network drive within Windows. I don't want to use any 3rd party software to access the linux server because I want to use the linux server as a backup for Bare Metal Restore. In order to do so, I need to be able to access the linux partition from within the Windows Recovery Enviroment where I cannot install any 3rd party software. The linux server should only be accessible from given IP addresses (e.g. the 2 windows servers). Does anyone know if the setup I would like to have is possible?

  Read the article

• Planning office network [closed]

  - by gakhov

  I'm planning to setup my office network from scratch and want to ask professional opinions or tips. My office is connected to Internet with Cable connection (100Mb/s). The devices i would like to connect are VoIP Phone (RJ-11), TV (WiFi/LAN), 3 laptops (WiFi), a few smartphones (WiFi), iPad (WiFi), Kindle (WiFi) and, probably, MediaServer (WiFi/LAN). As you can see, the most load will be on WiFi connections (probably, even if TV supports WiFi it's better to connect it by LAN?). So, i need help to choose the best routers combination (or even one?) to support stable connections for all these devices and minimize the total number of routers/adapters. Any thoughts? Thank you!

  Read the article

• TCP/IP communication between Hyper-V host and guests

  - by Tedd Hansen

  This may be a simple one. :) I have a simple Hyper-V setup with a few guest os running. The host has 1 physical network adapter with a static IP assigned to it. The guests have network adapters assigned to "Internet" (Hyper-V network) which is bound to the physical host network adapter (Hyper-V "External" connection type). I am not able to communicate (ping or anything else) between guests and host. I've checked firewall and it seems fine (ports open from anywhere still don't work). I'm trying to communicate with the hosts IP assigned to the same physical interface that the guests are sharing. Guests can communicate between them just fine. I can't seem to find any relevant setting (I might just be missing it). So my questions: How do I fix it so host and guests can communicate?

  Read the article

• good PCI-e Wireless card for Windows7?

  - by benwebdev

  Hi I've just build a 64bit Windows 7 PC but am unhappy with the piddly performance of the linksys USB wireless dingle I've used. Can anyone suggest a good PCIe alternative that will be stronger for connection and maybe faster. I dont see why my desktop should show a weaker performance on wireless than my laptop when its sat next to it or even my Palm Pre for that matter. any thoughts? UK based max around £60ish. thanks, Ben

  Read the article

• Set web browser (or other program) to use specific network

  - by Will

  my PC is connected to 3 different networks: 2 different LAN connections and a VPN connection. when i am connected to the vpn, i cannot browse to the LAN intranet as the DNS is all going through the vpn and it cannot see the domains on the LAN. Is there a way to set firefox/chrome/etc to use a specific connection, so that i don't have to disconnect from vpn to get to the other intranets?

  Read the article

• Internet connection sharing windows server 2008 R2

  - by This is it

  I have one windows server 2008 r2, and that server has 4 network interfaces (3 private, 1 internet connection). I would like to share internet connection with other 3 networks. Windows server firewall should make logs of data that is transfered. It should not be possible to connect directly to private networks from internet. How could I do it? Edit: I tried with NAT in RRAS, but it doesn't work. Here is the configuration: Server: IP private:192.168.0.1 IP public: xx.xx.xx.xx client IP:192.168.0.2 Default gateway: 192.168.0.1 Public and private interface added in NAT section of RRAS.

  Read the article

• Random “Lost connection to MySQL server at 'reading initial communication packet', system error: 0”

  - by user1606545

  Sometimes I get the error from MYSQL server: Lost connection to MySQL server at 'reading initial communication packet', system error: 0 I cannot find the cause, since most of the time it works, but every week for some hours I get this error. I googled, but there seem to be only users which have this error permanently. But in this case, it only occurs sometimes. I checked hosts.allow and hosts.deny, but the host is allowed and not denied. Also sometimes I get the error: File './database/table.MYD' not found (Errcode: 24) It occurs very rarely. But it occurs for some hours once a week, sometimes on multiple days, but suddenly the problem disappears again. I have checked the open files limit. It's 2048 and should be absolutely enough. I also tried to increase the number of open files nevertheless, but no effect. I thought, perhaps the process does not close some tables. But this is impossible, because after a while everythings o.k. again and the process opens maximum 100 tables at once. I also checked the MySQL-runtime-environment, and there were 930 opened files. I cannot explain that. After a while it's 129. I am running a MySQL-Server on a SUSE-Linux machine. I connect to the MySQL-Server from another host by the command line tool "mysql" and by MySQL-C-connector. The MySQL-Server is version 5.0.67.

  Read the article

• Inbound connections to a ubuntu machine running a VPN

  - by shanedowling

  Is it possible to open inbound connections to a machine connected to a VPN server? The machine is running ubuntu 9.10 with two network devices(a wireless card and ethernet port), I can connect to my machine locally using a local ip but when I try port forward using my router I can't connect from my external ip. Is there a way around this? I figure with 2 network devices I can vpn over one and use the other for inbound connections but I can't figure out how to do this. Thanks

  Read the article

• Any ideas why Ettercap filters aren't seeing packet data?

  - by Bryan

  I'm using an Ettercap filter to detect a query response coming back from a particular service on a remote machine. When I see a response from the service, I'm searching through the data in the packet to see if an offset is a specific value, and if so I'm changing the value at another offset. Trouble is, when I try this on a new virtual machine I built my Ettercap filter's no longer getting any data in the DATA.data variable available to it. if(ip.proto == TCP && tcp.src == 17867) { msg("Response seen!\n"); if(DATA.data + 2 == "\0x01") { msg("Flag detected!\n"); DATA.data + 5 = 0x09; } } The filter's getting applied to the traffic because "Response seen!" messages get printed out by Ettercap. However, "Flag detected!" messages do not. I think DATA.data is indeed empty because if I change my second "if" statement to check for DATA.data == "" then the "Flag detected!" message gets printed. Any ideas why this may be happening?! Also, if this is the wrong site to be asking questions like this, please let me know. I wasn't sure if it fit better here or somewhere like superuser or serverfault. By the way, this is a cross-post from StackOverflow... I should have posted on this forum instead I think. :)

  Read the article

• I can't use a custom theme on a network account

  - by Rev

  I'm an administrator for the computer I use, but I'm using a network account. I can set custom themes (non-Microsoft, I mean) on my local account but not on the network account. It's the same machine, just different accounts/domains. I tried to repatch the files from the network account, but it says they're already patched. Any ideas why this won't work? The themes don't show up in the Personalize menu, and I can't just double click the .theme file from the Themes folder in Windows 7 Pro. This is the theme I'm trying to use, by the way: http://fediafedia.deviantart.com/art/Windows-8-VS-for-Win7-258514188?q=boost%3Apopular%20windows%208%20theme&qo=0 Tried repatching the files, still nothing.

  Read the article

• bridge traffic limiting via tc

  - by jackhab

  I have a Linux machine running as a bridge simulating various network conditions. I use tc for this. Introducing delays or packet loss is quite simple but I got into trouble trying to configure bandwidth limiting. Can you, please, show me how to limit all the traffic going through my bridge without any special rules and condition, simply limit it to 1Mb/s? Thanks. PS Your favorite link to tc tutorial will be appreciated.

  Read the article

• Using Lan Management port - which kind of switch for remote control?

  - by zephyrus

  Hello everyone, I have no expertize in server hardware, however i have some IBM X3550 7978 and HP DL 160/G6 servers with 2 Lan ports, and a management port (that seem to be another Lan port). Have anyone tried to use the management to control remotely the low level functions of the servers (reboots for example) ? Which kind of switch or other devices have you used for this? thank you Massimiliano

  Read the article

• why would resetting the Netgear N300 router fix my Win 7 laptop's slow wifi?

  - by rjnagle

  In the past day the wifi download speeds of my Win 7 HP 64 bit laptop have slowed considerably. I am trying to troubleshoot the problem and to figure out whether it's hardware related (i.e., is the Intel(R) Centrino(R) Wireless-N 2230 the problem?) or router related. I have a Netgear N300 router connected to my modem. I'm using Speedtest to measure my speed. First, during my problem state, my ipad can download and upload at normal speeds. It's only my Win 7 laptop which is having problems. Because my ipad downloads at normal speeds, that would tell me that the problem is specific to the laptop (either HW or SW). But when I restarted my Netgear router, the laptop wifi problems disappeared. That just doesn't make sense. If we know that one device can connect properly to the router, why would a laptop have problems? What are some possible reasons why this might happen? Also, during my problem state, I noticed that on my laptop upload speeds were faster than my download speeds. Anybody have a guess about what might cause upload speeds on one device to be faster than another? Is there any actions i could take (or options to enable) so this problem won't occur. (I initially thought my problem might be software related or memory related -- Norton AV or browser plugins. But even after I disabled everything and made sure memory footprint was minimal, the slowdown was still occurring -- and it solved itself altogether when the router was reset).

  Read the article

• Cant ping ip on LAN. Port forward works fine though.

  - by Anoop

  I have a Solaris 11 machine running inside the LAN. It is a default install. I can access the machine and ping it if I ssh into my router (if it matters, it is running dd-wrt). I cannot ping the Solaris machine using ip address from any other machine inside the LAN. But if I setup port forwarding everything works perfectly fine. I can also use the port forward from outside the LAN (from my office) - which is good and how I want it to be. I can SSH and ping and do pretty much everything else from outside as well as inside but only as long as I have the port forwarded from my router. Why would I not be able to ping or ssh or even access the Solaris 11 machine from within the LAN - I have checked and couldn't find any firewall running on the Solaris 11 box. I even tried disabling every known firewall on the router (dd-wrt, it had something like SPI firewall running). I even tried setting a static IP for my Solaris box but all in vain! Please help me understand how and why this happens!! Thanks.

  Read the article

< Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >