Search Results

Search found 20099 results on 804 pages for 'virtual host'.

Page 239/804 | < Previous Page | 235 236 237 238 239 240 241 242 243 244 245 246  | Next Page >

• Can't connect to Wired Network after installing 12.04

  - by ezz9

  I have installed 12.04 into a used HP Compaq DC 7100 CMT. Plugged in LAN cable into the computer and it says network disconnected. from what I understand on the things I've read, it's not getting the address right, maybe it's just a guess (hardware address 00:16:35:78:47:bb). I know the LAN cable is working I can get on the net with the old computer. (Old computer is using device MAC address; Auto eth0 00:11:11:E6:4F:FE). I have put this address into the newer HP and it shows last used (minutes ago) but no Internet sever not found. I tried the hardware address it says never. I feel and think this should be easy to fix. But I just don't know. Here is the info everyone has asked for, but they never say what I should do. sudo lshw -C network; rfkill list; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; uname -a; ifconfig; route -n *-network description: ethernet interface product; NetXtreme BCM5751 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:40:00.0 logical name: eth0 verson: 01 serial: 00:16:35:78:47:bb size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000-fd configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion= 3.121 duplex=full firmware=5751-v3.29a latency=0 link=yes multicast=yes port=twi sted pair speed=100Mbit/s resources: irq:17 memory:f0400000-f040ffff auto lo iface lo inet loopback DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION= "Ubuntu 12.04 LTS" 00:00.0 host bridge [0600]: Inter Corporation 82915G/P/GV/GL/PL/910GL Memory Con troller Hub [8086:2580] (rev 04) 00.02.0 VGA compatible controller [0300]: Intel Corporation 82915G/GV/910GL inte grated Graphics Controller [8086:2582] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 03) 00:1c.1 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 [8086:2662] (rev 03) 00:1d.0 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #1 [8086:2658] (rev 03) 00:1d.1 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #2 [8086:2659] (rev 03) 00:1d.2 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #3 [8086:265a] (rev 03) 00:1d.3 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #4 [8086:265b] (rev 03) 00:1d.7 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB2 UHCI Controller [8086:265c] (rev 03) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI bridge [8086:244e] (rev d 3) 00:1e.2 Multimedia audio controller [0401]: Intel Corporation 82801FB/FBM/FR/FW/ FRW (ICH6 Family) AC'97 Autio conrtroller [8086:266e] (rev 03) 00:1f.0 ISA bridge [0601]: Intel Corporation 82801FB/RF (ICH6/ICH6R) LPC Interfa ce Bridge [8086:2640] (rev 03) 00:1f.1 IDE interface [0101]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 fami ly) IDE Controller [8086:266f] (rev 03) 00:1f.2 IDE interface [0101]: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Con troller [8086:2651] (rev 03) 40:00.0 Ethernet controller [0200]: Broadcom Corporation NetXreme BCM5751 Gigab it Ethernet PCI Express [14e4:1677} (rev 01) Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Linux bob-desktop 3.2.0-23-generic-pae #36-Ubuntu SMP Tpr 10 22:19:09 UTC 20 12 i686 i686 i386 GNU/Linux eth0 Link encap:Ethernet HWaddr 00:16:35:78:47:bb inet6 addr: fe80::216:35ff:47bb/64 Scope:link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2517 errors:0 dropped:0 overruns:0 frame:0 TX packets:164 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:164508 (164.5 KB) TX bytes: 40884 (40.0 KB) Interrupt:17 lo Link encap:Local loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3290 errors:0 dropped:0 overruns:0 frame:0 TX packets:3290 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen: 0 RX bytes:267212 (267.2 KB) TX bytes: 267212 (267.2 KB) Kernel Ip routing table Destination Gateway Genmask Flags Metric Ref Use Iface ran this sudo dhclient eth0 no reply ran this ip addr 1: lo <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST ,MULTICAST ,UP ,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000 link/enter 00:16:35:78:47:BB brd ff:ff:ff:ff:ff:ff inet 169.254.7.172/16 brd 169.254.255.255 scope link eth0:avahi inet6 fe80::216:35ff:fe78:47bb/64 scope link valid_lft forever preferred_lft forever Help please.

  Read the article

• Is windows a "second class citizen" in the django community?

  - by Daniel Upton

  I'm currently doing R&D for a web application which we plan to host ourselves initially and then allow customers to self host. My task has been evaluating web frameworks to see which would give us the biggest productivity initially and ease of maintence while also allowing us to easily support deployment to customer controlled environments. Our team has experience with ASP.NET (MVC and Webforms) and Ruby on Rails. Our experience with rails is that windows deployment is a very taboo subject and any questions on IRC or SO are met with knee jerk "why not linux" responses.. However in this case our target market may be running windows or linux servers. Is this also the case in django land? Is it possible with rubbish performance? Is it possible with lost of pain? Is it seen as reasonable and not treated as a completely stupid idea for not wanting to run linux?

  Read the article

• Photosynth Panoramic Deep Zoom Mosaic

  18 years ago Virtual Reality was all the rage remember The Lawnmower Man? 16 years ago Apple came out with QuickTime VR which changed the way people experienced panoramic photos on the web. QuickTime VR (virtual reality) (also known as QTVR) is a type of image file format supported by Apple's QuickTime. It allows the creation and viewing of photographically captured panoramas and the exploration of objects through images taken at multiple viewing angles. It functions as a plug-in for QuickTime. QuickTime...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• Juju didn't configure rabbitmq for openstack?

  - by SaM

  I have installed ubuntu Openstack HA with juju with all 24 servers. But my openstack is not working at all. On dashboard on every page I get errors saying "could not retrieve usage information", "could not retrieve volume information, "could not retrieve .....etc I spent hours and have discovered that juju has not done configuration correctly. I found that on cloud controller in nova.conf juju has added rabitmq vhost enrty, but that virtual host is not added in rabbitmq. Then how is its suppose to work? And on juju-gui canvas rabbimq is all green and is working fine, which in reality its not. I am really wondering if juju has really done correct configuration in all 24 servers now, I am getting the feeling that it would have been faster if I would have done openstack deployment manually instead of using juju. Why was the virtual host entry not added in rabbitmq? How should I solve this?

  Read the article

• Installing Yaws server on Ubuntu 12.04 (Using a cloud service)

  - by Lee Torres

  I'm trying to get a Yaws web server working on a cloud service (Amazon AWS). I've compilled and installed a local copy on the server. My problem is that I can't get Yaws to run while running on either port 8000 or port 80. I have the following configuration in yaws.conf: port = 8000 listen = 0.0.0.0 docroot = /home/ubuntu/yaws/www/test dir_listings = true This produces the following successful launch/result: Eshell V5.8.5 (abort with ^G) =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Using config file /home/ubuntu/yaws.conf =INFO REPORT==== 16-Sep-2012::17:21:06 === Ctlfile : /home/ubuntu/.yaws/yaws/default/CTL =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Listening to 0.0.0.0:8000 for <3> virtual servers: - http://domU-12-31-39-0B-1A-F6:8000 under /home/ubuntu/yaws/www/trial - =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Listening to 0.0.0.0:4443 for <1> virtual servers: - When I try to access the the url (http://ec2-72-44-47-235.compute-1.amazonaws.com), it never connects. I've tried using paping to check if port 80 or 8000 is open(http://code.google.com/p/paping/) and I get a "Host can not be resolved" error, so obviously something isn't working. I've also tried setting the yaws.conf so its at Port 80, appearing like this: port = 8000 listen = 0.0.0.0 docroot = /home/ubuntu/yaws/www/test dir_listings = true and I get the following error: =ERROR REPORT==== 16-Sep-2012::17:24:47 === Yaws: Failed to listen 0.0.0.0:80 : {error,eacces} =ERROR REPORT==== 16-Sep-2012::17:24:47 === Can't listen to socket: {error,eacces} =ERROR REPORT==== 16-Sep-2012::17:24:47 === Top proc died, terminate gserv =ERROR REPORT==== 16-Sep-2012::17:24:47 === Top proc died, terminate gserv =INFO REPORT==== 16-Sep-2012::17:24:47 === application: yaws exited: {shutdown,{yaws_app,start,[normal,[]]}} type: permanent {"Kernel pid terminated",application_controller," {application_start_failure,yaws,>>>>>>{shutdown,>{yaws_app,start,[normal,[]]}}}"} I've also opened up the port 80 using iptables. Running sudo iptables -L gives this output: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- ip-192-168-2-0.ec2.internal ip-192-168-2-16.ec2.internal tcp dpt:http ACCEPT tcp -- 0.0.0.0 anywhere tcp dpt:http ACCEPT all -- anywhere anywhere ctstate RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:http Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination In addition, I've gone to the security group panel in the Amazon AWS configuration area, and add ports 80, 8000, and 8080 to ip source 0.0.0.0 Please note: if you try to access the URL of the virtual server now, it likely won't connect because I'm not running currently running the yaws daemon. I've tested it when I've run yaws either through yaws or yaws -i Thanks for the patience

  Read the article

• Oracle Ebusiness Suite 12.1.3 Oracle VM templates

  - by wcoekaer

  Steven Chan just published a great blog entry that talks about the release of a new set of Oracle VM templates. Oracle Ebusiness Suite 12.1.3. You can find the blog post here. Templates are available for: E-Business Suite 12.1.3 Vision (64-bit) E-Business Suite 12.1.3 Production (32-bit) E-Business Suite 12.x Sparse Middle Tiers (32-bit and 64-bit) Thanks Steven! Why does this stuff matter? Well, in general, virtualization (or cloud) solutions provide an easy way to create Virtual Machines. Whether it's through a "cloud api" or just a virtualization API. But all you end up with, in the end, is still just a Virtual Machine... Maybe with an OS pre-installed/pre-configured. So you have flexibility of moving VMs around and providing a VM but what about the actual applications (anything more than a very basic app)? The application administrator then still has to go and install and configure the OS for that application and install the application and its patches and basic configuration so that the application user then can go in. Building gold images for complex software stacks that are not owned by the users/admins is always very difficult. With our templates, we provide a number of things : Oracle Linux pre-installed and pre-configured with the minimum required packages for that application to run. (so it's secure) Oracle Linux can be distributed and used for free or with a support subscription. There is no trial license, there is no registration key, no alpha version or community version versus enterprise version. You get what we provide in our engineered systems, what we provide support for, without change. Supported out of the box. No virtual Trial appliances, no prototypes, no POC. What you download is production ready without change. The applications are installed by the developers of the application. The database team builds database templates, the applications engineering team builds applications templates. The first boot/configuration scripts ask for the basic information such as hostname, ip address, user passwords and then go off and set everything up correctly. All tested together - application - operating system - hypervisor. not 3 (or more) products from 3(or more) different companies.

  Read the article

• fsockopen() error : Network is unreachable port 43 in php [closed]

  - by hamid

  i've writed some Php code that lookup for domain (whois) but it fails !! this is some of my code : function checkdomain($server,$domain){ global $response; $connection = fsockopen($server,43); fputs($connection, "domain " . $domain . "\r\n"); while(!feof($connection)){ $response .= fgets($connection, 4096); } fclose($connection); } checkdomain("whois.crsnic.net","www.example.com"); the code work on my localhost ( apache,php,mysql, OS - Win XP ) but when i uploaded it to my host (Linux) it failed. and i always see the Below Error/message : Warning: fsockopen() [function.fsockopen]: unable to connect to whois.crsnic.net:43 (Network is unreachable) in /home/hamid0011/public_html/whois/whois.php on line 37 what should i do ? is this my host's problem or whois server ( but it work in localhost ) or my code ? TNX

  Read the article

• GPL vs plugin interfaces not designed with a specific application in mind

  - by Kristóf Marussy

  I am not seeking or in need of legal advice, but an interesting though experiment came to my mind. Imagine the following situtation (I cannot really think about a concrete example and I am unsure if a real manifestation even exists): there is a free (libre) api A licensed under some permissive license or even LGPL. Non-free application B implements this api in order host plugins, but there are other free software doing the same thing. Moreover, there is plugin C acting as a plugin under api A. It links to library D, that is under GPL, so C is also under GPL. Plugins using A are loaded into hosts via a dlopen-like mechanism and use complex data structure for host-plugin communication. Neither B nor C distribute any files that may be required for A to function properly (like headers containing the structure definitions of A or dynamic libraries containing helper functions for A written by the authors of A), but such things may exist. Now some user installs application B and plugin C on his machine, along with anything that may be required for api A to function properly. Then he proceeds and loads C into B and creates some intellectual property with B which is not a piece of software. Did a GPL violation happend at some point, and if so, who violated GPL and why? The authors of C violate D's license by making C possible to be used in non-free host B? This is a possibility because they can't give and exception of GPL (like one described in http://www.gnu.org/licenses/gpl-faq.html#GPLPluginsInNF or http://www.gnu.org/licenses/gpl-faq.html#LinkingOverControlledInterface) due to D's license terms. The authors of B violate C's and D's license by making C possible to be loaded in B? This is a possibility because http://www.gnu.org/licenses/gpl-faq.html#NFUseGPLPlugins disallows the mechanisms A uses for communitation between the free and non-free modules. The authors of A, because the api may be used (and in this case, was used) for communication between GPL'd and non-free software. This would be extremely absurd. The user, because at the moment of loading B into C, he made a derived work of C. I think this is impossible, because he does not distribute it. But would the situation change is he decided to release a configuration file of B which makes B load C as a plugin? Nobody, because A counts as a 'system library', and both B and C directly interact only with A, not eachother. In a sane world, this would happen... A concrete example of A could be some kind of audio (think LADSPA) or image processing api. However, I could find no such interface (that is free software, generic and is also implemented by commercial tools). A real-world example could also be quite enlightening.

  Read the article

• IBM Brings Deduplication to Mainframes

  Big Blue unveils a virtual tape library with deduplication capabilities for backing up z/OS environments.

  Read the article

• Trouble switching to Dvorak on Ubuntu 12.04

  - by Dodgie

  I've decided to switch to Dvorak on my Ubuntu machine, but I'm having some trouble: First, I attempted to do this through the GUI -- System Settings - Keyboard Layout - add layout (plus sign) - English(programmer Dvorak). This didn't work at first, so I restarted my machine. It seemed to work at the password prompt (if only because QWERTY did not), but I couldn't get it to accept my password. I used the virtual keyboard option to enter my password with mouse clicks (the virtual keyboard was using the programmer's Dvorak Standard) and was able to get in that way. Once logged in, however, I was back to QWERTY. Second, I tried to switch on the command prompt -- $ loadkeys /usr/lib/kbd/keytables/dvorak.map The error message I received was "Couldn't get a file descriptor referring to the console " Does anyone know what I'm doing wrong? I've looked for a solution for these problems, but couldn't find anything.

  Read the article

• Elastic PaaS with WebLogic and OpenStack, part I

  - by Jernej Kaše

  In my previous blog I described the steps to get OpenStack on Solaris up and running. Now we'll explore how WebLogic and OpenStack can work together to deliver truly elastic Middleware Platform as a Service. Middleware / Platform as a Service goals First, let's define what PaaS should be : PaaS offerings facilitate the deployment of applications without the complexity of managing the underlying hardware and software and provisioning hosting capabilities. To break it down: - PaaS provides a complete platform for hosting solutions (Java EE, SOA, BPM, ...) - Infrastructure provisioning (virtual machine, OS, platform) and managing is hidden from the PaaS user [administrator or developer] - Additionally, PaaS could / should define target SLAs, and the platform should ensure the SLAs are meet automatically. PaaS use case To make it more tangible, we have an IT Administrator who has the requirement to deploy a Java EE enterprise application. The application is used by external users who need to submit reports by the end of each month. As a result, the number of concurrent users will fluctuate, with expected huge spikes around the end of each month. The SLA agreed by the management is that no more than 100 requests should be waiting to be processes at any given time. In addition, the IT admin has no more than 3 days to have the platform and the application operational. The Challenges Some of the challenges the IT Administrator is facing are: - how are we going to ensure the processing power? - how are we going to provision the (virtual) machines, Java EE platform and deploy the application? - how are we going to monitor the SLA? - how are we going to react to SLA, and increase capacity?  The Ideal Solution Ideally, the whole process should be automated, "set it and forget" and require no human interaction: - The vendor packages the solution as deployable image(s) - The images are deployed to the IaaS - From there, automated processes take care of SLA  Solution Architecture with WebLogic 12c, Dynamic Clusters, OpenStack & Solaris OracleSolaris provides OS and virtualisation through Solaris Zones OpenStack is a part of Solaris 11.2 and provides Cloud Management (console and API) WebLogic 12c with Dynamic Clusters provides the Platform Trafic Manager provides load balancing On top of out that, we are going to implement a small control script - Cloud Manager - which is going to monitor SLA through WebLogic Diagnostic Framework. In case there are more than 100 pending requests, the script will: - provision a new virtual machine based on image which is configured for the WebLogic domain - add the machine to WebLogic domain - Increase the number of servers in dynamic cluster - Start the newly provisioned server  Stay tuned for part II The hole solution with working demo will be presented in one of our Partner WebCasts in June, exact date TBA. Jernej Kaše is a Fusion Middleware Specialist working closely with Oracle Partners in the ECEMEA region to grow their business by leveraging Oracle technology.

  Read the article

• Fan control on Acer Aspire One D255 netbook

  - by AdamB

  I have Ubuntu netbook edition on my Acer Aspire One D255 netbook and I notice that I always hear the fan working at 100% despite the actual temperature. I run the sensors command its only at 13c, theres no reason why the fan needs to be running this hard at that temp. root@adam-netbook:~# sensors acpitz-virtual-0 Adapter: Virtual device temp1: +13.0°C (crit = +100.0°C) I'm guessing I may need some drivers in order to interact with the fan? Does anyone have any experience with this? It also seems that "sensors" may not be all that accurate, the temperature never seems to fluctuate.

  Read the article

• XNA: Networking gone totally out of sync

  - by MesserChups

  I'm creating a multiplayer interface for a game in 2D some of my friends made, and I'm stuck with a huge latency or sync problem. I started by adapting my game to the msdn xna network tutorial and right now when I join a SystemLink network session (1 host on PC and 1 client on Xbox) I can move two players, everything is ok, but few minutes later the two machines start being totally out of synchronization. When I move one player it takes 10 or 20 seconds (increasing with TIME) to take effect on the second machine. I've tried to : Create a thread which calls NetworkSession.Update() continuously as suggested on this forum, didn't worked. Call the Send() method one frame on 10, and the receive() method at each frame, didn't worked either. I've cleaned my code, flushed all buffers at each call and switched the host and client but the problem still remain... I hope you have a solution because I'm running out of ideas... Thanks SendPackets() code : protected override void SendPackets() { if ((NetworkSessionState)m_networkSession.SessionState == NetworkSessionState.Playing) //Only while playing { //Write in the packet manager m_packetWriter.Write(m_packetManager.PacketToSend.ToArray(), 0, (int)m_packetManager.PacketToSend.Position); m_packetManager.ResetPacket(); //flush //Sends the packets to all remote gamers foreach (NetworkGamer l_netGamer in m_networkSession.RemoteGamers) { if (m_packetWriter.Length != 0) { FirstLocalNetGamer.SendData(m_packetWriter, SendDataOptions.None, l_netGamer); } } m_packetWriter.Flush();//m m_packetWriter.Seek(0, 0); } } ReceivePackets() code : public override void ReceivePackets() { base.ReceivePackets(); if ((NetworkSessionState)m_networkSession.SessionState == NetworkSessionState.Playing) //Only while playing { if (m_networkSession.LocalGamers.Count > 0) //Verify that there's at least one local gamer { foreach (LocalNetworkGamer l_localGamer in m_networkSession.LocalGamers) { //every LocalNetworkGamer must read to flush their stream // Keep reading while packets are available. NetworkGamer l_oldSender = null; while (l_localGamer.IsDataAvailable) { // Read a single packet, even if we are the host, we must read to clear the queue NetworkGamer l_newSender; l_localGamer.ReceiveData(m_packetReader, out l_newSender); if (l_newSender != l_oldSender) { if ((!l_newSender.IsLocal) && (l_localGamer == FirstLocalNetGamer)) { //Parsing PacketReader to MemoryStream m_packetManager.Receive(new MemoryStream(m_packetReader.ReadBytes(m_packetReader.Length))); } } l_oldSender = l_newSender; m_packetReader.BaseStream.Flush(); m_packetReader.BaseStream.Seek(0, SeekOrigin.Begin); } } m_packetManager.ParsePackets(); } } }

  Read the article

• Using multiple A-records for my domain - do web browsers ever try more than one?

  - by Jonas

  If I add multiple A-records for my domain, they are returned in a round robin order by DNS-servers. E.g: 1.1.1.1 A example.com 1.1.1.2 A example.com 1.1.1.3 A example.com But how does webbrowsers react if the first host (1.1.1.1) is down (unreachable)? do they try the second host (1.1.1.2) or do they return a error message to the user? Are there any difference between the most popular browsers? If I implement my own application, I can implement so that the second is used in case the first is down, so it's possible. And this would be very helpful to create a fault tolerant website.

  Read the article

• Can't start Psychonauts game -- segfault

  - by tremby

  This looks similar to Psychonauts Humble Indie Bundle V error but I don't have the ERROR message (missing GL capability) and its solution does not work for me. When trying to run Psychonauts from the Humble Indie Bundle on my x86_64 laptop running Ubuntu 12.04 I get the following output: <bjn@segnus:/usr/local/games/psychonauts>$ ./Psychonauts STUBBED: fix up the rest of the SSE code first at DetectSSESupport (/home/icculus/projects/psychonauts/Source/CommonLibs/DFMath/MathGeneral.cpp:32) STUBBED: write me? at SetPCLanguage (/home/icculus/projects/psychonauts/Source/game/luatest/UnixMain.cpp:120) STUBBED: fix up the rest of the SSE code first at DetectCPUCaps (/home/icculus/projects/psychonauts/Source/game/luatest/Game/PCGameApp.cpp:223) STUBBED: check LANG envr var at _GetDefaultGameLanguage (/home/icculus/projects/psychonauts/Source/game/luatest/Game/GameApp.cpp:171) Console created Save path: /home/bjn/.local/share/Psychonauts Write path: WorkResource STUBBED: inline asm at SSEMul_4x4_4x4_2arg (/home/icculus/projects/psychonauts/Source/CommonLibs/DFMath/Matrix.cpp:710) STUBBED: inline asm at SSEMul_4x4_4x4_3arg (/home/icculus/projects/psychonauts/Source/CommonLibs/DFMath/Matrix.cpp:698) ******** unit test failed ******** STUBBED: VK_* at InitInputNames (/home/icculus/projects/psychonauts/Source/CommonLibs/DirectX/SDLInput.cpp:1220) No joysticks detected Transport started DaveD: NCListenSocket: Listening on port 40001 SDL_SetVideoMode() failed: Failed loading libGL.so.1 Start Up completed in 0.06 seconds [1] 9718 segmentation fault (core dumped) ./Psychonauts <bjn@segnus:/usr/local/games/psychonauts>$ Output of lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M-E LPC Interface Controller (rev 03) 00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 02:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) 02:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) 0c:00.0 Network controller: Intel Corporation WiFi Link 5100 Any ideas?

  Read the article

• How to configure apache / php / postfix website emails when using vhosts?

  - by Alistair Buxton

  I have a LAMP webserver configured to serve multiple websites. Each virtual host has various PHP applications, mainly Wordpress. When users sign up to the Wordpress sites, email is sent by PHP through to postfix, and then on to the receiver. The problem is that postfix is identifying itself to the remote server with the contents of /etc/hostname, which is not a fully qualified domain name. Some mail servers reject this and the mail bounces. Additionally, the return path is being set to one of the vitual host domains, seemingly at random. I could set /etc/hostname to one of the website domain names, but then the emails from the other websites would have a wrong server in the headers, and this would not fix the return-path issue. Possibly related, apache2 says "could not determine the server's fully qualified domain name" on startup. How do I fix this so that each website can send email without revealing the other websites hosted on the server?

  Read the article

• B2B 11.1.1.2 no proxy support for FTP

  - by nestor.reyes

  Have you seen this error while trying to use a proxy for a delivery channel within B2B?Transport error: Proxy type must be defined when Proxy host has been specified. Proxy type must be defined when Proxy host has been specified.If so, you are not alone. FTP does not support proxy.  Also note the following entry in the release notes. http://download.oracle.com/docs/cd/E15523_01/relnotes.1111/e10133/b2b.htm#CHDJAFBC 15.1.45 FTP Listening Channel Does Not Have Proxy Support The Generic FTP-1.0 protocol for a listening channel does not have proxy support.The wording states listening channel, but it also applies for delivery channel.

  Read the article

• Am 10.02. startet WebCast-Serie für Java Entwickler und WebLogic Interessenten: WebLogic Developer - Get the latest on Oracle WebLogic Server and Java EE 6

  - by Thomas Leopold

  v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 21 false false false DE X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Accelerate Your Development with Oracle WebLogic Suite Many organisations are reducing travel, conference, and training budgets for their developers without any change to the results expected of those developers. So how can you keep up with the latest developments?By receiving training, delivered free of charge, at your desk!Join us during February and March for a series of online events designed and run by the development team at Oracle. Learn how Oracle WebLogic Suite enables a whole new level of productivity for enterprise developers.Virtual Developer Day - 10th FebruaryStarting with our Virtual Developer Day on 10th February, join us for a blend of hands-on labs, live chat and presentations covering the latest on WebLogic, Java EE 6 and the programming tenets that have made it a true platform breakthrough.Weekly WebLogic Webcasts from 17th February to 17th MarchAfterwards, join us every week from 17th February to 17th March for our weekly one-hour webcasts where we will show you how to build an application from the ground up using Java and JEE technologies. Presented by the engineering team for WebLogic, these webcasts will be of great value to developers and architects, not just those already using WebLogic.For registration, full session abstracts and schedule please click here. Don't miss out! Register now to join our virtual events and keep up with all the latest developments. Find out more and register now Copyright © 2011, Oracle Corporation and/or its affiliates.All rights reserved. Contact Us | Legal Notices and Terms of Use | Privacy Statement

  Read the article

• DNS slows down on development environment

  - by Sequenzia

  I have a local development environment setup on my Mac. I am running an Ubuntu Web Server inside of a Virtual Box VM. I setup a host file on my Mac that points my dev site to the IP of the Ubuntu Virtual Server. Everything works good other than the fact a lot (not all) of the time it takes more than 5 seconds to load a page. I used firebug to track down where the problem is and when it's slow the DNS part of my request is taking over 5 seconds. Like I said it's not all the time. Sometimes it resolves and loads the page within milliseconds. The same page one click will be super fast and then the next time it takes over 5 seconds. It's really slowing me down and I am not sure what is causing it.

  Read the article

• Are libc versions tied to kernel versions?

  - by mathematician1975

  After reading the answers to my previous question I have come to the conclusion that an answer to the following question is what I was actually looking for: Does a particular version of the kernel require a particular version of libc to run properly? Basically my problem stems from building an application on my 12.04 ubuntu and trying to run it on 8.04. I have since learned from this and other stackexchange forums that it is backward compatibility of libc that causes these problems. Therefore what I am perhaps naively trying to do is build the same version of libc that exists on my target and then link against that on my host when I build the application. Then in an ideal world when I copy this to the host, having been linked to the "correct" libc it should work (in my head at least). I have been totally unable to find a way to install an older libc on my system, and wondered if each version is tightly bound to a kernel version, hence the above question.

  Read the article

• OBIEE 11.1.1 - Tips for In-place Upgrade from 11.1.1.6 to 11.1.1.7.x

  - by Ahmed Awan

  Tips: – Use the Test to Production (T2P) / cloning process (movement scripts). For example: – Clone up the existing 11.1.1.6 environment.– Move the cloned copy to the new location / host (same 11.1.1.6.0 version at this point).– Patch new location / host (11.1.1.6) to the 11.1.1.7 level.– Switch to Production. – How to use movement scripts for OBIEE: 20.1 Introduction to the Movement Scripts , for details refer to: http://docs.oracle.com/cd/E29542_01/core.1111/e10105/clone.htm#CACHFECE 21.4.7.1 Moving Oracle Business Intelligence to a New Target Environment, for details refer to: http://docs.oracle.com/cd/E29542_01/core.1111/e10105/testprod.htm#CHDIAEFA http://docs.oracle.com/cd/E29542_01/core.1111/e10105/testprod.htm#BABGJGCF – Perform in-place upgrade to 11.1.1.7.0 using manual steps / Upgrade wizard, refer to: http://docs.oracle.com/cd/E28280_01/upgrade.1111/e16452/bi_plan.htm#BABECJJH

  Read the article

• Ubuntu 12.04 installer Crashed

  - by Umair Mustafa

  I downloaded Multiple times Ubuntu 12.04 and Ubuntu 12.04.1. And tried to install them using first Virtual box if it work I move to install on actual drive. I dont knw but 12.04.1 dont wanna install on my system So i downloaded 12.04 release and installed it on Virtual box and it installed perfectly then i moved on to install it as Dual OS along with windows 7 but the installer crashed just like the other version and I dont know what the heck is the problem with ubuntu OS Installers. Ubuntu really need to work on their Installer. I love Ubuntu but such things are really headache. At first I thought image was not properly so i burned on another dvd but alas no use same stupid error. Now there are 3 images of 12.04 and 2 images of 12.04.1 and none of them is working on my system. And wasted two dvds. Does anyone know how to solve this problemo.

  Read the article

• My Reference for Amy Lewis

  - by Denise McInerney

  The 2013 election campaign for the PASS Board of Directors is underway. There are seven qualified candidates running this year. They all offer a wealth of experience volunteering for PASS and the SQL Server community. One of these candidates, Amy Lewis, asked me to write a reference for her to include on her candidate application. I have a lot of experience working with Amy and was pleased to provide this reference: I enthusiastically support Amy Lewis as a candidate for the PASS Board of Directors. I have known and worked with Amy in various PASS' volunteer capacities for years, starting when we were both leaders of SIGs (the precursors to the Virtual Chapters.) In that time I have seen Amy grow as a leader, taking on increasing responsibility and developing her leadership skills in the process. From the Program Committee to the BI Virtual Chapter to her local user group's SQL Saturday Amy has demonstrated a capacity to organize and lead volunteers. A successful leader delivers results, and does so in a way that encourages and empowers the people she is working with; Amy embodies this leadership style. As Director for Virtual Chapters I have most recently worked with Amy in her capacity of DW/BI VC Leader. This VC is one of our largest and most active, and Amy's leadership is a key contribution to that success. I was pleased to see that Amy was also thinking about succession and prepared other volunteers to take over the chapter leadership. Amy has shown an understanding of PASS' strategic goals and has focused her volunteer efforts to help us reach those goals. For the past couple of years we have been trying to expand PASS reach and relevance to SQL communities around the world. The VCs are a key vehicle for this expansion. Amy embraced this idea and organized the VC to engage volunteers in Europe & Australia and provide content that could reach SQL professionals in those regions. A second key strategy for PASS is expanding into the data analytics space. Again Amy rose to the occasion helping to shape the program for our first Business Analytics Conference and leveraging the BI VC to promote the event. By all measures I think Amy is prepared to serve on the Board and contribute in a positive way.

  Read the article

• Using ext4 in VMware machine

  First of all, using a journaling filesystems like NTFS, ext4, XFS, or JFS (not to name all of them) is a very good idea and nowadays unthinkable not to do. Linux offers a good variety of different option as journaling filesystem for your system. Since years I am using SGI's XFS and I am pretty confident with stability, performance and liability of the system. In earlier years I had to struggle with incompatibilities between XFS and the boot loader. Using an ext2 formatted /boot solved this issue. But, wow, that is ages ago! Lately, I had to setup a fresh Lucid Lynx (Ubuntu 10.04 LTS) system for a change of our internal groupware / messaging system. Therefore, I fired up a new virtual machine with almost standard configuration in VMware Server and run through our network-based PXE boot and installation procedure. At a certain step in this process, Ubuntu asks you about the partitioning of your hard drive(s). Honestly, I have to say that only out of curiousity I sticked to the "default" suggestion and gave my faith and trust into the Ubuntu installation routine... Resulting to have an ext4 based root mount point ( / ). The rest of the installation went on without further concerns or worries. Note:I really can't remember why I chose to go away from my favourite... Well, it should turn out to be the wrong decision after all. Ok, let's continue the story about ext4 in a VMware based virtual machine. After some hours installing additional packages and configuring the new system using LDAP for general authentication and login, I had an "out-of-the-box" usable enterprise messaging system based on Zarafa 6.40 Community Edition inclusive proper SSL-based Webaccess interface and Z-Push extension for ActiveSync with my Nokia mobile. Straightforward and pretty nice for the time spent on the setup. Having priority on other tasks I let the system just running and didn't pay any further attention at all. Until I run into an upgrade of "Mail for Exchange" on Symbian OS. My mobile did not bother me at all with the upgrade and everything went smooth, but trying to re-establish the ActiveSync connection to the Zarafa messaging system resulted in a frustating situation. So, I shifted my focus back to the Linux system and I was amazed to figure out that the root had been remounted readonly due to hard drive failures or at least ext4 reported errors. Firing up Google only confirmed my concerns and it seems that using ext4 for VMware based virtual machines does not look like a stable and reliable candidate to me. You might consider reading those external resources: ext4 fs corruption under VMWare Server 2.01Bug #389555 - ext4 filesystem corruption Well, I learned my lesson and ext{2|3|4} based filesystems are not going to be used on any of my Linux systems or customer installations in the future. Addendum: I did not try this setup in other virtualization environments like VirtualBox, qemu, kvm, Xen, etc.

  Read the article

• Receiving requests where absolute URL on page are morphed to relative URLs

  - by Jacob

  In our web pages, we have a hyperlink with an href to an absolute URL: https://some.other.host.com/blah.aspx?var1=val1&var2=val2 For some reason, in our logs, we see a lot of requests to URLs of this format: http://our.site.com/https:/some.other.host.com/blah.aspx?var1=val1&var2=val2 We don't have any JavaScript that would request that URL; it only appears inside of a hyperlink. Is there some sort of known bot, browser plugin, bug, etc. that could be responsible for these requests being made?

  Read the article

< Previous Page | 235 236 237 238 239 240 241 242 243 244 245 246  | Next Page >