Search Results

Search found 751 results on 31 pages for 'quad'.

Page 24/31 | < Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >

  • Nginx + php-fpm - recv() error

    - by Ilya Biryukov
    I get the follow error in the nginx log [error] 17734#0: *6643 recv() failed (104: Connection reset by peer) while reading response header from upstream, client: [cut], server: [cut], request: "GET /venues HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "[cut]" I have a dedicated box with 8 gb ram, quad core chip. Good server. Nginx, php-fpm & mysql all latest versions running under ubuntu 10.04 I only get this when I stress test the server with siege. If I increase the number of concurrent connections to 100, I can get up to 20% of all requests to fail. Furthermore, I don't get this on pages that have no mysql queries. And only a few failures on pages with moderate number of queries. Bit, I'm not sure if that's got to do anything with it. I have a feeling this is something to do with php. But I can't figure it out. Any suggestions of where to even start looking? Update: and the php error log is silent. No record of anything going wrong

    Read the article

  • HP DL185 - very slow disk read speed

    - by fistameeny
    Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

    Read the article

  • EMC VNX iSCSI setup - unsure about SP/port assignment

    - by pauska
    We have a new VNX5300 waiting to get configured, and I need to plan out the network infrastructure before the EMC tech arrives. It has 4x1gbit iSCSI per SP (8 ports in total), and I'd like to get the most out of the performance until we jump over to 10gig iSCSI. From what I can read from the docs - the recommendation is to use only two ports per SP, with 1 active and 1 passive. Why is this? It seems kind of pointless to have quad-port i/o-modules and then recommend to not use more than two of them? Also - I'm a bit unsure about the zoning. The best practices guide state that you should separate each port on each SP from each other on different logical networks. Does this mean that I have to create 4 logical networks to be able to use all 8 ports? It also gives the following example: Does this mean that A0 and B0 should sit on the same physical switch aswell? Won't this make all traffic go on one switch (if both A1 and B1 are passive)? Edit: Another brainpuzzle I don't get it - each host (as in server) should not have more iSCSI bandwidth available than the storage processor. What on earth does this matter? If serverA have 1gbit and serverB have 100mbit, then the resulting bandwith between them is 100mbit. How can this result in some kind of oversubscription? Edit4: Wait, what. Active and passive ports? The VNX runs in a ALUA configuration with asymmetrical active/active.. there shouldn't be any passive ports, only preferred ones..

    Read the article

  • MacBook Pro and Backtrack 5R1 Configuration

    - by user119346
    I have a Macbook pro Quad core (2.2/8gb ram/750gb hdd). I have went through tons of forums on the Internet, but none of them seemed to be updated for the current Backtrack 5R1, or the question of getting it to correctly work on the MBP. Can anyone help? I don’t have a USB Dongle, and I want to be able to use the internal airport extreme wireless of the MBP to use BT 5R1. I have downloaded Backtrack 5R1 onto VMWare Fusion, and got it up and running, but to no avail. It keeps recognizing my card as a Ethernet connection. Kismac wont recognize the card either. So what I am asking for is this: The proper “download method.” for Backtrack 5R1 to my MacBook Pro. (YES I AM WILLING TO RE-DOWNLOAD BT 5R1). The Complete process from start to finish, UP TO DATE, from someone who has done this using an MBP Running Lion OSX. The proper tweaks, settings, or commands to get my airport extreme wireless card to work (it is BROADCOM 4331 I think). The wireless connection I need to use the tools on both Backtrack 5R1 and Kismac. I mainly need to test WEP cracking on my network for security. The difference between running BT 5R1 on VMWARE Fusion and running from downloading it directly to the MBP, if there is, How to download it directly to the MBP?

    Read the article

  • Virtualization in Ubuntu 9.10

    - by Jeff Dege
    I have an existing Centos 5 installation. I would like to upgrade to Ubuntu. Thing is, I don't want to be down for as long as it will take to get my entire environment moved over - software installed, connectivity configured, etc. I'd like to take it one step at a time. But I don't really want to keep rebooting back and forth from the new OS to the old OS. That's what I did last time I upgraded to a new OS, and it got old real fast. So, since my new MB is virtualization-ready (AMD Phenom II 945 quad-core), I figured I could create a virtual machine, under the new OS installation, that ran the old OS installation. The problem is that the documentation I've been able to find has been pretty sparse. I've found a lot of possibilities, and little info on which would be capable of doing what I want. I have a new Ubuntu 9.10 installation, and a second disk containing the Centos 5 installation. And I don't know where to go next. Any help would be appreciated.

    Read the article

  • Server freezes while installing Redhat Enterprise Linux Server 6

    - by eisaacson
    We've tried both the first options Install or upgrade an existing system Install system with basic video driver When trying option #1, it gets to a screen that has a solid cursor about halfway down, then freezes. When trying option #2, it freezes at the point where it says: Waiting for hardware to initialize... Of course, we bought the unsupported version and haven't found anything to help us so far. Here are the specs to the server in the original post: ASUS P8Z68-M Pro LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard with UEFI BIOS RAIDMAX Reiter ATX-305WBP Black Steel / Plastic ATX Mid Tower Computer Case 450W Power Supply Intel Core i7-2600 Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 2000 BX80623I72600 16GB Ram OCZ Agility 3 SSD 120GB From some of the posts out there could the UEFI Bios or the Sandy Bridge processor be a culprit here? We just tried the DVD on a different computer and it got past that point with ease. It's a standard Dell build compared to our custom machine. Could it be having difficulty recognizing drivers? How do we get past that?

    Read the article

  • Varnish, Nginx, Apache, APC, Meteor, Cpanel & Wordpress On A Single Server, Any Good?

    - by Aahan
    Yes, I have read many close questions, but I needed a specific answer and hence this question. First, these are my new server specifications: Linux Server (CentOS), Intel Xeon 3470 Quad Core (2.93GHz x 4) processor, 4 GB DDR3 Memory, 1TB Hard Disk Space, 10 TB Bandwidth and 9 Dedicated IPs. AIM: To speed up my wordpress blog + Increase server's capacity to handle heavy load PLAN: This is how I am planning to setup my server - - VARNISH (in the front, to cache server responses) NGINX (to effectively handle static content & overcome the C10k problem) APACHE (behind Nginx, to effectively deliver dynamic content) APC (PHP page, database & object caching) CPANEL (which requires Apache, and I require it) WORDPRESS W3 TOTAL CACHE (caching plugin for Wordpress). So , will the setup work? Have anyone tried it? Please shower your thoughts and knowledge. NOTE: I can't do without Apache because I am used to that .htaccess & Cpanel stuff. So, it's not any option. All others are options. Please try to help. I hope I am clear in what I wanted to ask.

    Read the article

  • What are these CPU cache settings? Snoop Filter, ACL prefetch, HW prefetch

    - by eater
    I was in my BIOS setup turning on VT-x support today and saw these other settings. A little googling indicates that they each seem to turn on some sort of optimization to do with the CPU's L2 cache. They were all turned off by default. The processor in question is an Intel Xeon quad-core 3.4GHz (X5492). My OS is Linux 2.6.35.10-74.fc14.x86_64 #1 SMP Thu Dec 23 16:04:50 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux. I have 4GB of RAM if that matters. Here's what the BIOS manufacturer has to say: Snoop Filter Enabling the snoop filter typically improves performance by reducing snoop traffic on the frontside bus in dual processor configurations. Well I like the sound of improved performance. Why would the BIOS have this off by default? Or by dual processor do they not mean multi-core? Regardless, is there a downside if this is on? ACL Prefetch When enabled, the Adjacent Cache Line Prefetcher fetches both cache lines that comprise a cache line pair when it determines required data is not currently in its cache. When disabled, the processor will only fetch the cache line required by the processor. HW Prefetch Fetches an extra line of data into L2 from external memory. Both of these sound like optimizations that have some drawbacks. What are the reasons to turn them on? What are the reasons to leave them off. Why is the default off?

    Read the article

  • windows 7 turns off itself everyday at about 9am

    - by Radek
    I was given this comp at work and after a week or so this strange thing started to happen in the middle of doing something :-( It turns off itself at about 9.10am every morning Just once a day and it works fine after it had it little nap. it happens both if the comp was on all night or I turned it off before leaving the office. I tried to swapped the memory as I was told that there was an issue with memory. But moving or removing any memory did not make any difference. I am not aware that I would install any program that could cause that. I installed AVG and set it up to do every day scan about 8am + if restart is needed it requires user confirmation. 'The Software Protection service has stopped' few minutes before it turned off itself but it happened also at other times without the computer turned off. I turned off Windows automatic updates as the first thing when I got the comp configuration Windows 7 Ultimate Intel Core2 Quad Q9550 at 2.8GH, 8GB RAM ST31000528AS Barracuda 7200.12 SATA 3Gb/s 1TB Update Below message are logged when I turn the comp on again. Message 1: The previous system shutdown at 9:08:54 AM on ?6/?29/?2010 was unexpected. Message 2: Level:Critical Source: Kernel Power EventID 41 Task Category (63) The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Log after manual restart Update 2 (task scheduler)

    Read the article

  • Server 2008 RAID 5 Write Speeds

    - by Solipsism
    I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

    Read the article

  • Poor performance on IIS7, only on Windows Server 2008, fine on Windows 7?

    - by user32005
    Hi, I'm new to IIS7 but have experience with other versions. I've been working on an application that works great in a dev environment (as always) but when I push it to a windows server 2008/IIS7 box performance takes a noticeable hit. The dev environment is Windows7/IIS7. The configuration in IIS is the same on the dev box as the server. I've tried all sorts of things to try and find a reason for this but I cant come to any conclusion. I've ruled out database problems on the live box as all data is cached after the first request. I've confirmed this to be true and made sure there is no additional database traffic. I've ruled out network issues with a combination of monitoring requests with fiddler and local debugging on the server. Whenever the code runs on the server there seems to be a performance issue. The server: Intel Core 2 Quad CPU Q6600 @ 2.40ghz with 2gb RAM. I know this is not fantastic but I was expecting it to at least perform as well as my dev environment (which is running much more on a lower spec). The CPU using peaks at under 60%, and memory usage is less than half of the available. I've enabled failed request tracing and most of the time is spent in a custom HttpModule, this module works to handle every request, I cant get any more detail as to what within the module may be causing the problem. Any ideas, I've been pulling my hair out for days now. Thanks

    Read the article

  • Virtual Machine Network Services causes networking problems in Vista Enterprise 64 bit install

    - by Bill
    I have a Quad-core/8GB Vista Enterprise 64-bit (SP2) installation on which I installed Virtual PC 2007. I have a problem that is opposite of all that I found searching around the Internet--everybody has problems making network connections from their guest VM. When Virtual Machine Network Services is enabled in the protocol stack for my network card across a reboot, it causes access problems to the network. The amount of time to login in using a domain credentialed account is upwards of 3 minutes, then after reaching the desktop the network and sharing center shows that my connection to the domain is unauthenticated. Disabling and re-enabling the Virtual Machine Network Services (uncheck in network properties/apply/recheck/apply) fixes the problem. And as long as I have the VMNS disabled when I shutdown the restart runs smoothly. I just have to remember to enable after login and disable before shutdown. I have un-installed and re-installed Virtual PC 2007 multiple times with restarts between. The install consists of the SP1 + a KB patch for guest resolution fix. Any help would be greatly appreciated. Some additional information... At one point during my hairpulling and teethgnashing with this, I tried to ping my primary DC and observed some weird responses: (Our DC is 10.10.10.25, my dynamic IP was 10.10.10.203) Reply from 10.10.10.203, Destination host unreachable. Request timed out. Reply from 10.10.10.25: ... This is not consistently repeatable, but thought it might strike a chord with someone.

    Read the article

  • Load is 0, yet site crawls (sometimes). What gives?

    - by Yegor
    I have a ~1.5-2mil page views per day site running on 2 servers. One for mysql, other for everything else. Mysql box has a load of 3, frontend is usually 0.0-0.1. Both are dual quad core with 8GB ram running SAS drives in raid5. CPU is idle for majority of the time, iowait is non-existent. Im running nginx, memcache, and site is built on php. Half the time everything runs perfect, while at other times it lags something severe, when it takes 10-15 seconds for a page to load. Page execution time is always super low, but it seems to hang, waiting for something before it actually loads the page. Whats even more weird is that it only happens to 1 file on the site (but its the one thats most commonly accessed, that actually loads the content on the site). Other pages are super fast at all times, even when it takes 15 seconds to load actual content. I have nginx_stats plugin installed, and if I monitor it, the lag spikes happen when the write column starts going above 100, and it frequently does... all the way to 500-1000. It does so at totally random times... not when traffic is heavy... it can do this in the middle of the night, and work perfectly at 5pm when traffic is at its highest. Any ideas?

    Read the article

  • Windows 7 starts getting sluggish over a few days

    - by munrobasher
    Myself and the other developer are running Windows 7 Enterprise 64 bit with 8GB RAM on different Gigabyte motherboards with Quad core Intel CPUs. Most of the time, it runs like a dream. We use VMware workstation a lot (hence the 8GB) and that works well. Except... now and then, after the PCs have been on for a few days, the whole system starts getting really sluggish doing certain tasks. The other's developer's system is far worse than mine with it taking up to a minute to launch IE. Today, mine has gone sluggish but nowhere near as bad. For example, normally when I click on a new tab in IE, it's instant. Today, there's an obvious delay. Right-clicking in this window to trigger iSpell is normally instant, right now it takes about five seconds. I've got resource monitor open on my second monitor and when I did that right-click, there was no obvious peak in CPU, disk or memory. A reboot does fix it so it does sound like a resource issue but haven't a clue what might be to blame. The two computers have similarities (same spec) but also differences (like motherboard, RAM & CPU models). So I guess the question is, any pointers on diagnosing why a PC is sluggish? What could cause such a right-click slow down in IE for example? It sounds like such a simple operation. NOTE: whilst typing this message alone, it was fine performance wise. I can click around the page no problem but right-click still is noticeable slow. Will reboot over lunch... Cheers, Rob.

    Read the article

  • SQL Server performance on VSphere 4.0

    - by Charles
    We are having a performance issue that we cannot explain with our VMWare environment and I am hoping someone here may be able to help. We have a web application that uses a databases backend. We have an SQL 2005 Cluster setup on Windows 2003 R2 between a physical node and a virtual node. Both physical servers are identical 2950's with 2x Xeaon x5460 Quad Core CPUs and 64GB of memory, 16GB allocated to the OS. We are utilizing an iSCSI San for all cluster disks. The problem is this, when utilizing the application under a repeated stress testing that adds CPUs to the cluster nodes, the Physical node scales from 1 pCPU to 8 pCPUs, meaning we see continued performance increases. When testing the node running Vsphere, we have the expected 12% performance hit for being virtual but we still scale from 1 vCPU to 4 vCPUs like the physical but beyond this performance drops off, by the time we get to 8 vCPUs we are seeing performance numbers worse than at 4 vCPUs. Again, both nodes are configured identically in terms of hardware, Guest OS, SQL Configurations etc and there is no traffic other than the testing on the system. There are no other VMs on the virtual server so there should be no competition for resources. We have contacted VMWare for help but they have not really been any suggesting things like setting SQL Processor Affinity which, while being helpful would have the same net effect on each box and should not change our results in the least. We have looked at all of VMWare's SQL Tuning guides with regards to VSphere with no benefit, please help!

    Read the article

  • Windows Server 2008 R2 running at a snail's pace

    - by Django Reinhardt
    Really weird problem here. Our main web server has started running at a snail's pace, for absolutely no reason we can discern. Even after restarting the machine, when there's no little or no ram usage and CPU usage is fluctuating between 0 and 30%, simple tasks, like opening Internet Explorer, or waiting for My Computer to open, take forever. There are no processes hogging system resources that we can see... the machine itself is just exhibiting extremely slow behaviour. I've never seen a machine do this. A lot of security updates had built up, so we decided to let Windows install them. When we looked through the history upon restarting, though, they had failed with error code 800706BA. I don't know if this could be related or not. Any help in this matter would be greatly appreciated. As mentioned in the title, we're running a Windows Server 2008 R2 machine. It's also running SQL Server and IIS. It has 16GB of RAM and a decent Quad Core processor. It's also been fine until now -- and we haven't changed a thing. Thanks for any help.

    Read the article

  • 100% CPU load on Ubuntu 10.04.3 LTS 64bit

    - by deadtired
    I have 2 days since I am trying to fix this issue, with no success. The server is a mysql database server. Hardware: DELL Poweredge 1950, 2x Intel Xeon Quad Core E5345 @ 2.33GHz, 16 Gb mem, 2x 146Gb SAS (software RAID1) Software: Ubuntu 10.04.3 LTS, MySQL 5.1.41 Issue: while mysql is not used and runs with no database, everything seems alright. As soon as I install a database, it has the reason to bring all 8 cores in 100% with low memory consumption. So, you can imagine the load average goes high (I saw 212 load average for the first time). The server doesn't become unresponsive, but you can see it's slow while browsing the project installed. Additional info: the database used is not more than 24MB and it was moved from a server with less resources and a lot more larger databases. So it's not the database/project. my.cnf is not a reason also, as I used both default one and the one I use on the same distribution on another server.What is interesting is that mysql doesn't close any process and runs to the limit of the max_connections. Logs are quiet. Nothing there. I switched to this Ubuntu version after I suspected some problems in the newly Ubuntu 11.10 server. This one worked alright for an hour after I made a kernel upgrade to 3.0.1 (it was using the memory also) I tested disk speed and seems alright. Some more output on the running server: dstat -cndymlp -N total -D total 3: htop command: Idea? Did anyone meet the same problem? Any fix you can think of?

    Read the article

  • USB question (how durable is it, how should I workaround this)

    - by Shiki
    The plot is quite simple. Got a Razer mouse. If I plug it in, it works. After a shutdown/hibernation, I have to replug it entirely at the back of the PC. (It works in my laptop even after severel shutdown, etc, so yes I guess it's my motherboard.. but it still got 2 years of warranty and it comes with quad SLI, its not an old motherboard at all. (MSI P7N SLI FI (bought it after a hungarian guy's recommendation)). So. I only could come up with one "solution". Get 3 USB cable (you know, USB-USB). If its possible the shortest ones (don't know if the responsibility/anything will worsen), AND replug only the middle+closest to the USB port junction, since those are replaceable. What do you think? Any other idea? (BIOS is updated, mouse driver ... doesn't really matter, the mouse won't even blink a bit after this happens. It lights up and goes totally dead.)

    Read the article

  • Installed Bunch of New Fonts on Windows 7 - Now None Show Up and System Lags

    - by Josh Stodola
    So I went to install about 5,000 fonts on my Windows 7 64-bit machine. It was slow to install them, and I had to leave. I came back and my PC was shut down, and I had to go through the Windows recovery BS when I powered it on. Now my computer runs EXTREMELY slow and any program that has a font menu locks up my whole machine (nothing in Microsoft Office works). When I go to "Fonts" in the control panel, it says 0 items. I went through all of the font settings trying to get them to appear. Nothing helps. I tried to bring up the Character Map and that froze up my machine too. How can I fix this? If I do not get this issue resolved soon, I am wiping this drive and going back to XP (and probably never purchasing another version of Windows again). I never had any issues with XP and have had nothing but performance problems when switching to Windows 7. My quad-core intel extreme with 8GB of RAM should never flinch with the kind of work that I do, and something simple like playing a song off an external HD takes up to five seconds on Windows 7. Unbelievable that I had to pay for this crap!

    Read the article

  • Compressing and copying large files on Windows Server?

    - by Aaron
    I've been having a hard time copying large database backups from the database server to a test box at another site. I'm open to any ideas that would help me get this database moved without having to resort to a USB hard drive and the mail. The database server is running Windows Server 2003 R2 Enterprise, 16 GB of RAM and two quad-core 3.0 GHz Xeon X5450s. Files are SQL Server 2005 backup files between 100 GB and 250 GB. The pipe is not the fastest and SQL Server backup files typically compress down to 10-40% of the original, so it made sense to me to compress the files first. I've tried a number of methods, including: gzip 1.2.4 (UnxUtils) and 1.3.12 (GnuWin) bzip2 1.0.1 (UnxUtils) and 1.0.5 (Cygwin) WinRAR 3.90 7-Zip 4.65 (7za.exe) I've attempted to use WinRAR and 7-Zip options for splitting into multiple segments. 7za.exe has worked well for me for database backups on another server, which has ~50 GB backups. I've also tried splitting the .BAK file first with various utilities and compressing the resulting segments. No joy with that approach either- no matter the tool I've tried, it ends up butting against the size of the file. Especially frustrating is that I've transferred files of similar size on Unix boxes without problems using rsync+ssh. Installing an SSH server is not an option for the situation I'm in, unfortunately. For example, this is how 7-Zip dies: H:\dbatmp>7za.exe a -t7z -v250m -mx3 h:\dbatmp\zip\db-20100419_1228.7z h:\dbatmp\db-20100419_1228.bak 7-Zip (A) 4.65 Copyright (c) 1999-2009 Igor Pavlov 2009-02-03 Scanning Creating archive h:\dbatmp\zip\db-20100419_1228.7z Compressing db-20100419_1228.bak System error: Unspecified error

    Read the article

  • Is there any way to limit the turbo boost speed / intensity on i7 lap?

    - by Anonymous
    I've just got a used i7 laptop, one of these overheating pavilions from HP with quad cores. And I really want to find a compromise between the temp and performance. If I use linpack, or some other heavy benchmark, the temp easily gets to 95+, and having a TJ of 100 Degrees, for a 2630QM model, it really gets me throttling, that no cooling pad or even an industrial fan could solve. I figured later that it is due to turbo boost, and if I set my power settings to use 99% of the CPU instead of 100%, and it seems to disable the turbo boost, so the temp gets better. But then again it loses quite a bit of performance. The regular clock is 2GHz, and in turbo boost it gets to 2.6Ghz, but I just wonder if I could limit it to around 2.3Ghz, that would be a real nice thing. Also there is another question I've hard time getting answer to. It seems to me that clocks are very quickly boosting up to max even when not needed, eg, it's ok if the CPU has 0% load, the clocks get to their 800MHz, but even if it gets to about 5% it quickly jumps to a max and even popping up turbo, which seems very strange to me. So I wonder if there is any way to adjust the sensitivity of the Speed Step feature. I believe it would be more logical to demand increased clock if it hits let's say 50% load. I do understand that most of these features are probably hardwired somewhere in the CPU itself or the MB, which has no tuning options just like on many laptops. But I would appreciate if you could recommend some thing, or some software. Thanks

    Read the article

  • Mac, VNC and multiple monitors

    - by MarqueIV
    I asked a similar question here before but apparently I wasn't as clear as I had expected by the responses. That said, I'll try again. I have a Mac Pro with quad monitors which I would like to access remotely. I've been using VNC for this (either via screen sharing or a dedicated VNC client), which works, but the VNC protocol matches the physical layout/resolutions of attached monitors. One of the things I like about Microsoft's Remote Desktop (Terminal Server) client is that when you connect, it blanks out the local screens and sets the resolution to a client-specified setting. In other words, when natively running Windows, even though I'm running a physical 30" monitor flanked by 2 24" monitors as well as a 21" Cintiq monitor, I can set the Remote Desktop resolution to match my notebook's screen giving me a native, single-monitor configuration. As soon as I disconnect (and you log back in locally), the desktop un-blanks and the resolution resets back to the four physically attached monitors. Again, VNC works and yes I know I can use 5901, 5902...n to attach VNC to a specific monitor as opposed to the entire desktop, but I'm still at the mercy of trying to look at a 2560x1600 resolution on a 1280x800 screen. I'm left with either scaling (everything's too small) or panning/scrolling (it's like playing hide-and-seek with your documents!) SO... anyone know of any Mac-based remote software (client and server) that will let me connect to my Mac Pro and reset the resolution by the client, just like you can in Windows, or am I SOL?

    Read the article

  • Need Help Scoping a Server to use for study (MCITP Ent Admin + SharePoint 2010)

    - by AVFamily76
    i need to study for mcitp, but i also need to study for sharepoint 2010 i have a poweredge 1850 with two single-core CPUs + two 73G drives - it kills me on electricity, so don't want to use it, and it won't do VT, but it could be one of three boxes for a lab that's cheap, but will cost a lot on electricity i was thinking . . . OPTION #1 Opteron 4170 HE (50 watt chip), 6-core, only two-bills ($200), but the board's are $250, so that's an $800 box, then get another box to dual-boot Win7/Hyper-V on the cheap...? OPTION #2 Used Quad - but how many VM's that are really banging away could it run at same time? (Server 2008r2, SQL 2008r2, Search Server) OPTION #3 Study from books and just get one box that can run two VM's at same time, even if slowly. the last time i had and used a home lab was five years ago when i had a DC, SQL, Exchange and business app box, that's where i got my server skills was just banging on it for four years, but didn't read any books, so now i have to get certified and know the material, and just am not sure how much attention i should pay to the box i use versus the studying time and reading. sorry it's a subjective question, and am obviously open to all sorts of abuse here, but hope you can tell me also how many VM's i can run at the same time given what they'll be doing (SQL and SharePoint FAST search server are resource hungry) thanks!

    Read the article

  • Replacing HD in an MacOS 10.6.8 server caused all shares to fail

    - by Cheesus
    I'm hoping someone might have a helpful suggestion about this problem. We have 2 MacOSX servers available for file sharing. (quad Xeons - 2GB RAM, both 10.6.8), No.1 is an Open Directory Master with 50+ user accounts, No.2 has only 2 local accounts (/local/Default) and looks at the OD Master for all user accounts (/LDAPv3/10.x.x.20/) Both servers have 3 internal HD's, The boot volume with only Server OS and minimal Apps. A 'DataShare' HD (500GB) and a backup drive (500GB). After upgrading the DataShare HD in Server No.2 from a small internal HD (500GB) to larger capacity (2TB) drive, users are unable to connect to shares on Server No.2. Users get an error "There are no shares available or you are not allowed to access them on the server" The process I followed was to use Carbon Copy Cloner to create an exact copy of the original data drive (keeps all ownership data, UID, permissions, last edit date and time). Everything booted up ok, no indication there was any issues. (Paths to the sharepoint look good) Notes during troubleshooting - Server1 is operating perfectly, all users can access shares and authenticate etc. - I've checked the SACL (Server Access Control List) settings is ok. - On Server2 in the Server Admin' app, I can see all the shares listed ok. The paths seem valid, I can disable / reenable the shares, no errors. - On Server2 'workgroup manager' lists all the accounts from the OD Master in the LDAP dir view. All seems fine from here. Basically everything looks normal but no file shares on Server2 can be accessed from regular users.

    Read the article

  • Faster, secure, protocol/code required for long-distance transfer.

    - by Chopper3
    I've ran into a problem and I'm looking for a new secure protocol/client/server that's faster over a 1Gb/s fibre link - let me tell you the story... I have a pair of redundant, diversely-routed, 1Gb/s links over a distance of around 250 miles or so (not dark fibre but a dedicated point to point link, not a mesh). At the 'client' end I have a HP DL380 G5 (2 x dual-core 2.66Ghz Xeon's, 4GB, Windows 2003EE 32-bit), at the 'server' end I have a HP BL460c G6 (2 x quad-core 2.53Ghz Xeons, 48GB, Oracle Linux 5.3 64-bit). I need to transfer around 500 x 2GB files per week from the client to the server machines per week - but the transfer NEEDS to be secure. Using both iPerf or regular FTP I can get ~80MB/s of transfer pretty consistently, which is great. Using WinSCP or Windows SFTP I can't seem to get more that ~3-4MB/s, at this point the server's CPU is 3% busy while CPU0 of the client goes to ~30% utilised. We've tried editing various TCP window sizes with little success. Both ends are connected to quite low-usage Cisco Cat6509's with Sup720's. I can replace the client machine with a newer machine and/or move it to Linux - but this will take time. Clearly these single-threaded secure Windows clients are introducing too much latency doing their encryption. So a few questions/thoughts; Are there any higher performing secure protocols or client software for Windows that I could try? I'm pretty protocol-gnostic so long as it'll work between Windows and Linux. Should I be using hardware to do the encryption, either in the client or the network parts? If so what would you recommend? I'm not convinced that just swapping the server would be that much faster, the CPU was only at 30% but then again that's higher than I'd have expected given the load - moving to Linux at the client end may be a better idea but would be quite disruptive. Am I missing a trick? Thanks in advance.

    Read the article

< Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >