Search Results

Search found 6479 results on 260 pages for 'audio analysis'.

Page 242/260 | < Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249  | Next Page >

• HP SmartArray P400: How to repair failed logical drive?

  - by TegtmeierDE

  I have a HP Server with SmartArray P400 controller (incl. 256 MB Cache/Battery Backup) with a logicaldrive with replaced failed physicaldrive that does not rebuild. This is how it looked when I detected the error: ~# /usr/sbin/hpacucli ctrl slot=0 show config Smart Array P400 in Slot 0 (Embedded) (sn: XXXX) array A (SATA, Unused Space: 0 MB) logicaldrive 1 (698.6 GB, RAID 1, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SATA, 750 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SATA, 750 GB, OK) array B (SATA, Unused Space: 0 MB) logicaldrive 2 (2.7 TB, RAID 5, Failed) physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SATA, 750 GB, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SATA, 750 GB, OK) physicaldrive 2I:1:5 (port 2I:box 1:bay 5, SATA, 750 GB, OK) physicaldrive 2I:1:6 (port 2I:box 1:bay 6, SATA, 750 GB, Failed) physicaldrive 2I:1:7 (port 2I:box 1:bay 7, SATA, 750 GB, OK) unassigned physicaldrive 2I:1:8 (port 2I:box 1:bay 8, SATA, 750 GB, OK) ~# I thought that I had drive 2I:1:8 configured as a spare for Array A and Array B, but it seems this was not the case :-(. I noticed the problem due to I/O errors on the host, even if only 1 physicaldrive of the RAID5 is failed. Does someone know why this could happen? The logicaldrive should go into "Degraded" mode but still be fully accessible from the host os!? I first tried to add the unassigned drive 2I:1:8 as a spare to logicaldrive 2, but this was not possible: ~# /usr/sbin/hpacucli ctrl slot=0 array B add spares=2I:1:8 Error: This operation is not supported with the current configuration. Use the "show" command on devices to show additional details about the configuration. ~# Interestingly it is possible to add the unassigned drive to the first array without problems. I thought maybe the controller put the array into "failed" state due to the missing spare and protects failed arrays from modification. So I tried was to reenable the logicaldrive (to add the spare afterwards): ~# /usr/sbin/hpacucli ctrl slot=0 ld 2 modify reenable Warning: Any previously existing data on the logical drive may not be valid or recoverable. Continue? (y/n) y Error: This operation is not supported with the current configuration. Use the "show" command on devices to show additional details about the configuration. ~# But as you can see, re-enabling the logicaldrive this was not possible. Now I replaced the failed drive by hotswapping it with the unassigned drive. The status now looks like this: ~# /usr/sbin/hpacucli ctrl slot=0 show config Smart Array P400 in Slot 0 (Embedded) (sn: XXXX) array A (SATA, Unused Space: 0 MB) logicaldrive 1 (698.6 GB, RAID 1, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SATA, 750 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SATA, 750 GB, OK) array B (SATA, Unused Space: 0 MB) logicaldrive 2 (2.7 TB, RAID 5, Failed) physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SATA, 750 GB, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SATA, 750 GB, OK) physicaldrive 2I:1:5 (port 2I:box 1:bay 5, SATA, 750 GB, OK) physicaldrive 2I:1:6 (port 2I:box 1:bay 6, SATA, 750 GB, OK) physicaldrive 2I:1:7 (port 2I:box 1:bay 7, SATA, 750 GB, OK) ~# The logical drive is still not accessible. Why is it not rebuilding? What can I do? FYI, this is the configuration of my controller: ~# /usr/sbin/hpacucli ctrl slot=0 show Smart Array P400 in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: XXXX Cache Serial Number: XXXX RAID 6 (ADG) Status: Enabled Controller Status: OK Chassis Slot: Hardware Revision: Rev E Firmware Version: 5.22 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Analysis Inconsistency Notification: Disabled Raid1 Write Buffering: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Accelerator Ratio: 25% Read / 75% Write Drive Write Cache: Disabled Total Cache Size: 256 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True ~# Thanks for you help in advance.

  Read the article

• Win7 playback of dvr-ms files stutters

  - by Jim Lynn

  I've just had to install Windows 7 on my Media Center machine because my Vista installation had a faulty drive. I've got the latest drivers that I can find - Intel 945GM integrated Graphics, Realtek audio drivers. Things are working OK with one exception. Playback of old recordings, from dvr-ms format files, is choppy. The picture freezes for a fraction of a second, then quickly catches up. The sound is uninterrupted and doesn't pause. These freezes happen once every 5 seconds or so. It's very regular. Playback of Live TV from the digital tuner is perfectly smooth. DVD playback is perfectly smooth. As an experiment, I used the MPEG editing package VideoReDo to create a small test file in three different formats. This program takes the raw MPEG streams and repackages them into the desired container. I took the same clip and created three files in three formats: dvr-ms (Microsoft's old recorded TV format); mpg (standard MPEG); and ts (raw MPEG transport stream of the kind often produced by PVRs). When these three files are played back under Windows 7, the mpg and ts files play smoothly, but the dvr-ms file stutters. The last piece of data I have is that two other Windows 7 machines can play back dvr-ms files smoothly with no stuttering. One is a netbook, with less grunt than the media centre. So there must be something specific about my Media Center machine that's causing the problem. Does anyone have any idea where I can look now? I don't know much about AV software, codecs, filter graphs etc. but I suspect that's where the problem lies. Rendering the video isn't the problem, but extracting the streams is. How would I go about diagnosing the problem? Edited to add: I just used the GraphStudio tool to look at the filter graph on the offending PC. The filter graph it uses by default for dvr-ms looks identical to the other machines, and, interestingly, when I play the files using GraphStudio they run smoothly. Under Windows Media Player and Windows Media Center they stutter. I'd like to see the filter graph for WMP but GraphStudio won't show it. It looks like WMP and WMC are using a different decoding path to GraphStudio. Edited again to add: Today I purchased a new HDTV. The same Media Center driving the TV at 1080p is now playing back the old Recorded TV files smoothly, without stuttering. So whatever the cause of the original problem, using a different resolution seems to have removed the problem. It might also explain why nobody else has had this problem. I doubt many people use Media Centre with a 14in portable TV.

  Read the article

• svnstat script

  - by Kyle Hodgson

  So I'm building out a shell script to check out all of our relevant svn repositories for analysis in svnstat. I've gotten all of this to work manually, now I'm writing up a bash script in cygwin on my Vista laptop, as I intend to move this to a Linux server at some point. Edit: I gave up on this and wrote a simple .bat script. I'll figure out the Linux deployment some other way. Edit: added the sleep 30 and svn log commands. I can tell now, with the svn log command, that it's not getting to the svn log ... this time, it did Applications, and ran the log, and then check out Database, and froze. I'll put the sleep 30 before and after the log this time. co2.sh #!/bin/bash function checkout { mkdir $1 svn checkout svn://dev-server/$1 $1 svn log --verbose --xml >> svn.log $1 sleep 30 } cd /cygdrive/c/Users/My\ User/Documents/Repos/wc checkout Applications checkout Database checkout WebServer/www.mysite.com checkout WebServer/anotherhost.mysite.com checkout WebServer/AnotherApp checkout WebServer/thirdhost.mysite.com checkout WebServer/fourthhost.mysite.com checkout WebServer/WebServices It works, for the most part - but for some reason it has a tendency to stop working after a few repositories, usually right after finishing a repository before going to the next one. When it fails, it will not recover on its own. I've tried commenting out the svn line, it goes in and creates all the directories just fine when I do that - so its not that. I'm looking for direction as well as direct advice. Cygwin has been very stable for me, but I did start using the native rxvt instead of "bash in a cmd.exe window" recently. I don't think that's the problem, as I've left top on remote systems running all night and rxvt didn't seem to mind. Also I haven't done any bash scripting in cygwin so I suppose this might not be recommended; though I can't see why not. I don't want all of WebServer, hence me only checking out certain folders like that. What I suspect is that something is hanging up the svn checkout. Any ideas here? Edit: this time when I hit ctrl+z to cancel out, I forgot I was on Windows and typed ps to see if the job was still running; and as you can see there are lots of svn processes hanging around... strange. Kyle Hodgson@KyleHodgson-PC ~/winUser/Documents/Repos $ Kyle Hodgson@KyleHodgson-PC ~/winUser/Documents/Repos $ jobs [1]- Stopped bash co2.sh [2]+ Stopped ./co2.sh Kyle Hodgson@KyleHodgson-PC ~/winUser/Documents/Repos $ kill %1 [1]- Stopped bash co2.sh Kyle Hodgson@KyleHodgson-PC ~/winUser/Documents/Repos $ [1]- Terminated bash co2.sh Kyle Hodgson@KyleHodgson-PC ~/winUser/Documents/Repos $ Kyle Hodgson@KyleHodgson-PC ~/winUser/Documents/Repos $ Kyle Hodgson@KyleHodgson-PC ~/winUser/Documents/Repos $ ps PID PPID PGID WINPID TTY UID STIME COMMAND 7872 1 7872 2340 0 1000 Jun 29 /usr/bin/svn 7752 1 6140 7828 1 1000 Jun 29 /usr/bin/svn 6192 1 5044 2192 1 1000 Jun 30 /usr/bin/svn 7292 1 7452 1796 1 1000 Jun 30 /usr/bin/svn 6236 1 7304 7468 2 1000 Jul 2 /usr/bin/svn 1564 1 5032 7144 2 1000 Jul 2 /usr/bin/svn 9072 1 3960 6276 3 1000 Jul 3 /usr/bin/svn 5876 1 5876 5876 con 1000 11:22:10 /usr/bin/rxvt 924 5876 924 10192 4 1000 11:22:10 /usr/bin/bash 7212 1 7332 5584 4 1000 13:17:54 /usr/bin/svn 9412 1 5480 8840 4 1000 15:38:16 /usr/bin/svn S 8128 924 8128 9452 4 1000 17:38:05 /usr/bin/bash 9132 8128 8128 8172 4 1000 17:43:25 /usr/bin/svn 3512 1 3512 3512 con 1000 17:43:50 /usr/bin/rxvt I 10200 3512 10200 6616 5 1000 17:43:51 /usr/bin/bash 9732 1 9732 9732 con 1000 17:45:55 /usr/bin/rxvt 3148 9732 3148 8976 6 1000 17:45:55 /usr/bin/bash 5856 3148 5856 876 6 1000 17:51:00 /usr/bin/vim 7736 924 7736 8036 4 1000 17:53:26 /usr/bin/ps Kyle Hodgson@KyleHodgson-PC ~/winUser/Documents/Repos $ jobs [2]+ Stopped ./co2.sh Kyle Hodgson@KyleHodgson-PC ~/winUser/Documents/Repos $ Here's an strace on the PID of the hung svn program, it's been like this for hours. Looks like its just doing nothing. I keep suspecting that some interruption on the server is causing this; does svn have a locking mechanism I'm not aware of? Kyle Hodgson@KyleHodgson-PC ~/winUser/Documents/Repos $ strace -p 7304 ********************************************** Program name: C:\cygwin\bin\svn.exe (pid 7304, ppid 6408) App version: 1005.25, api: 0.156 DLL version: 1005.25, api: 0.156 DLL build: 2008-06-12 19:34 OS version: Windows NT-6.0 Heap size: 402653184 Date/Time: 2009-07-06 18:20:11 **********************************************

  Read the article

• Graphics driver for ubuntu on dell latitude XT

  - by marc.riera

  Hi, we have a laptop (dell latitude xt) on our company, and we would like to install ubuntu on it. windows 7 works fine out of the box, so the hardware is fine. since this laptop has a touchscreen we just installed ubuntu 10.10 netbook edition 32x. But, we do not manage to enable the touchscreen, neither the vga graphic drivers. this is the output from lspci, if somebody cares. 00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 7930 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS7932 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc Device 7934 00:06.0 PCI bridge: ATI Technologies Inc RS7936 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc Device 7937 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Xpress 1250 03:01.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 03:01.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 03:01.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0b:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 03) I've tryied to install ati drivers 9.3 , which I downloaded and installed, unpacked and installed, builded and installed, but nothing worked. Looks like the latests version is just accepted to work on jaunty 9.04, so they are kind of old. what else I can do? thanks. Marc Information added: lsusb and lspci -n |grep 01:05.0 sysop@wl083517:~$ lspci -n |grep 01:05.0 01:05.0 0300: 1002:7942 sysop@wl083517:~$ lsusb Bus 006 Device 002: ID 413c:8138 Dell Computer Corp. Wireless 5520 Voda I Mobile Broadband (3G HSDPA) Minicard EAP-SIM Port Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 413c:8140 Dell Computer Corp. Wireless 360 Bluetooth Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1b96:0001 N-Trig Duosense Transparent Electromagnetic Digitizer Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 03f0:1807 Hewlett-Packard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sysop@wl083517:~$

  Read the article

• How do you handle authentication across domains?

  - by William Ratcliff

  I'm trying to save users of our services from having to have multiple accounts/passwords. I'm in a large organization and there's one group that handles part of user authentication for users who are from outside the facility (primarily for administrative functions). They store a secure cookie to establish a session and communicate only via HTTPS via the browser. Sessions expire either through: 1) explicit logout of the user 2) Inactivity 3) Browser closes My team is trying to write a web application to help users analyze data that they've taken (or are currently taking) while at our facility. We need to determine if a user is 1) authenticated 2) Some identifier for that user so we can store state for them (what analysis they are working on, etc.) So, the problem is how do you authenticate across domains (the authentication server for the other application lives in a border region between public and private--we will live in the public region). We have come up with some scenarios and I'd like advice about what is best practice, or if there is one we haven't considered. Let's start with the case where the user is authenticated with the authentication server. 1) The authentication server leaves a public cookie in the browser with their primary key for a user. If this is deemed sensitive, they encrypt it on their server and we have the key to decrypt it on our server. When the user visits our site, we check for this public cookie. We extract the user_id and use a public api for the authentication server to request if the user is logged in. If they are, they send us a response with: response={ userid :we can then map this to our own user ids. If necessary, we can request additional information such as email-address/display name once (to notify them if long running jobs are done, or to share results with other people, like with google_docs). account_is_active:Make sure that the account is still valid session_is_active: Is their session still active? If we query this for a valid user, this will have a side effect that we will reset the last_time_session_activated value and thus prolong their session with the authentication server last_time_session_activated: let us know how much time they have left ip_address_session_started_from:make sure the person at our site is coming from the same ip as they started the session at } Given this response, we either accept them as authenticated and move on with our app, or redirect them to the login page for the authentication server (question: if we give an encrypted portion of the response (signed by us) with the page to redirect them to, do we open any gaping security holes in the authentication server)? The flaw that we've found with this is that if the user visits evilsite.com and they look at the session cookie and send a query to the public api of the authentication server, they can keep the session alive and if our original user leaves the machine without logging out, then the next user will be able to access their session (this was possible before, but having the session alive eternally makes this worse). 2) The authentication server redirects all requests made to our domain to us and we send responses back through them to the user. Essentially, they act as a proxy. The advantage of this is that we can handshake with the authentication server, so it's safe to be trusted with the email address/name of the user and they don't have to reenter it So, if the user tries to go to: authentication_site/mysite_page1 they are redirected to mysite. Which would you choose, or is there a better way? The goal is to minimize the "Yet Another Password/Yet another username" problem... Thanks!!!!

  Read the article

• creating a heirarchy of terminals or workspaces

  - by intuited

  <rant This question occurred to me ('occurred' meaning 'whispered seductively in my ear for the 100th time') while using GNU-screen, so I'll make that my example. However this is a much more general question about user interfaces and what I perceive as a flawmissing feature in every implementation I've yet seen. I'm wondering if there is some way to create a heirarchy/tree of terminals in a screen session. EG I'd like to have something like 1 bash 1.1 bash 1.2 bash 2 bash 3 bash 3.1 bash 3.1.1 bash 3.1.2 bash It would be good if the terminals could be labelled instead of having to be navigated to via some arrangement that I suspect doesn't exist. So then you could jump to one using eg ^A:goto happydays or ^A:goto dykstra.angry. So to generalize that: Firefox, Chrome, Internet Explorer, gnome-terminal, roxterm, konsole, yakuake, OpenOffice, Microsoft Office, Mr. Snuffaluppagus's Funtime Carousel™, and Your Mom's Jam Browser™ all offer the ability to create a flat set of tabs containing documents of an identical nature: web pages, terminals, documents, fun rideable animals, and jams. GNU-screen implements the same functionality without using tabs. Linux and OS/X window managers provide the ability to organize windows into an array of workspaces, which amounts to again, the same deal. Over the past few years, this has become a more or less ubiquitous concept which has been righteously welcomed into the far reaches of the computer interface funfest. Heavy users of these systems quickly encounter a problem with it: the set of entities is flat. In the case of workspaces, an option may be available to create a 2d array. However none of these applications furnish their users with the ability to create heirarchies, similar to filesystem directory structures, containing instances of their particular contained type. I for one am consistently bothered by this, and am wondering if the community can offer some wisdom as to why this has not happened in any of the foremost collections of computational functionality our culture has yet produced. Or if perhaps it has and I'm just an ignorant savage. I'd like to be able to not only group things into a tree structure, but also to create references (aka symbolic links, aka pointers) from one part of the structure to another, as well as apply properties (eg default directory, colorscheme, ...) recursively downward from a given node. I see no reason why we shouldn't be able to save these structures as known sessions, and apply tags to particular instances. So then you can sort through them by tag, find them by name, or just use the arrow keys (with an appropriate modifier) to move left or right and in or out of a given level. Another key combo would serve to create a branch in the place of the current terminal/webpage/lifelike statue/spreadsheet/spreadsheet sheet/presentation/jam and move that entity into the new branch, then create a fresh one as a sibling to it: a second leaf node within the same branch node. They would get along well. I find it a bit astonishing that this hasn't happened yet, and the only reason I can venture as a guess is that the creators of these fine systems do not consider such functionality to be useful to a significant portion of their userbase. I posit that the probability that that such an assumption would be correct is pretty low. On the other hand, given the relative ease with which such structures can be implemented using modern libraries/languages, it doesn't seem likely that difficulty of implementation would be a major roadblock. If it could be done in 1972 or whenever within the constraints of a filesystem driver, it should be relatively painless to implement in 2010 in a fullblown application. Given that all of these systems are capable of maintaining a set of equivalent entities, it seems unlikely that a major infrastructure overhaul would be necessary in order to enable a navigable heirarchy of them. </rant Mostly I'm just looking to start up a discussion and/or brainstorming on this topic. Any ideas, examples, criticism, or analysis are quite welcome. * Mr. Snuffaluppagus's Funtime Carousel is a registered trademark of Children's Television Workshop Inc. * Your Mom's Jam Browser is a registered trademark of Your Mom Inc.

  Read the article

• Weird random application hang problem

  - by haridsv

  I am trying to understand an application hang problem that started up lately on my windows xp system. The system runs fine for days (sometimes) without ever shutting down or putting it to sleep, but the problem first shows up as one of the apps hanging. The application's UI stops responding or one or more background threads hang, so even though the GUI is responding, it is not doing anything (e.g., in VirtualDub's case, the UI responds fine, but the job doesn't progress and I won't even be able to abort it). The weirdness part comes from the fact that if I try to kill such an app, the program that is used to kill it goes into the same mode (i.e, that hangs instead of the original). E.g., if I use Process Explorer to kill it, the original program exits, but procexp now hangs. If I use another instance of procexp to kill the one that is hanging, this repeats, so there is always at least one program hanging in that state. This is not specific to procexp, I tried the native task manager and even the "End Process" dialog from windows explorer that shows up when you try to close a non-responsive GUI (in this case, the explorer itself hangs). The only program that didn't hang after the kill, is the command line taskkill. However, in this case, explorer hangs instead of taskkill. Also, once this problem starts manifesting, it soon ends up freezing the whole system to the extent that even a clean shutdown is not possible, so I have learned to reboot as soon as I notice this problem, however this is very inconvenient, as I often have encoding batch jobs going on which can't continue the job after the restart. The longer I leave the system running after seeing this problem, the more applications get into this state. I have tried to do a repair install but that didn't make any difference. I also uninstalled some of the newer installs, but again no difference. I tried to search online, but got inundating results for generic hang and crash related problems. Though I couldn't notice any pattern, it seems as though the problem is more frequent if I have some video encoding going on at that time. I had the system running for days when I only do browsing and internet audio/video chat before I decide to start encoding something and the problem starts to show up. I am not too sure if it is the encoding program that first hangs, though I almost always noticed that too hanging (like the VirtualDub stopping to make progress). I also had to reboot 3 times on one day when I was heavily experimenting with encoding. I would appreciate any help in narrowing down this problem and save me the trouble of reinstalling. I don't especially want to loose my gotd installs.

  Read the article

• Windows 7 playback of dvr-Microsoft files stutters

  - by Jim Lynn

  I've just had to install Windows 7 on my Media Center machine because my Vista installation had a faulty drive. I've got the latest drivers that I can find - Intel 945GM integrated Graphics, Realtek audio drivers. Things are working OK with one exception. Playback of old recordings, from dvr-Microsoft format files, is choppy. The picture freezes for a fraction of a second, then quickly catches up. The sound is uninterrupted and doesn't pause. These freezes happen once every 5 seconds or so. It's very regular. Playback of Live TV from the digital tuner is perfectly smooth. DVD playback is perfectly smooth. As an experiment, I used the MPEG editing package VideoReDo to create a small test file in three different formats. This program takes the raw MPEG streams and repackages them into the desired container. I took the same clip and created three files in three formats: dvr-Microsoft (Microsoft's old recorded TV format); mpg (standard MPEG); and ts (raw MPEG transport stream of the kind often produced by PVRs). When these three files are played back under Windows 7, the mpg and ts files play smoothly, but the dvr-Microsoft file stutters. The last piece of data I have is that two other Windows 7 machines can play back dvr-Microsoft files smoothly with no stuttering. One is a netbook, with less grunt than the media centre. So there must be something specific about my Media Center machine that's causing the problem. Does anyone have any idea where I can look now? I don't know much about AV software, codecs, filter graphs etc. but I suspect that's where the problem lies. Rendering the video isn't the problem, but extracting the streams is. How would I go about diagnosing the problem? Edited to add: I just used the GraphStudio tool to look at the filter graph on the offending PC. The filter graph it uses by default for dvr-Microsoft looks identical to the other machines, and, interestingly, when I play the files using GraphStudio they run smoothly. Under Windows Media Player and Windows Media Center they stutter. I'd like to see the filter graph for Windows Media Player but GraphStudio won't show it. It looks like Windows Media Player and WMC are using a different decoding path to GraphStudio. Edited again to add: Today I purchased a new HDTV. The same Media Center driving the TV at 1080p is now playing back the old Recorded TV files smoothly, without stuttering. So whatever the cause of the original problem, using a different resolution seems to have removed the problem. It might also explain why nobody else has had this problem. I doubt many people use Media Centre with a 14in portable TV.

  Read the article

• Windows 7 BSOD - ntoskrnl?

  - by Ken Mason

  2 new HP Pavilion notebooks with 7 Home Premium pre-loaded with Norton. My first act was to use the Norton Removal Tool and load ZoneAlarm free and AVG Free. Frequent random BSOD's ever since...I found my way into Debug and have had various reports regarding ntoskrnl, depending on the status of symbols. It's been many years since I played with (DOS 3.x) debug, so this has been a considerable fumble. Excerpts follow and any insights would be greatly appreciated, as I am not a developer: ADDITIONAL_DEBUG_TEXT: Use '!findthebuild' command to search for the target build information. If the build information is available, run '!findthebuild -s ; .reload' to set symbol path and load symbols. MODULE_NAME: nt FAULTING_MODULE: fffff8000305d000 nt DEBUG_FLR_IMAGE_TIMESTAMP: 4b88cfeb BUGCHECK_STR: 0x7f_8 CUSTOMER_CRASH_COUNT: 1 DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT CURRENT_IRQL: 0 LAST_CONTROL_TRANSFER: from fffff800030ccb69 to fffff800030cd600 STACK_TEXT: fffff80004d6fd28 fffff800030ccb69 : 000000000000007f 0000000000000008 0000000080050033 00000000000006f8 : nt+0x70600 fffff80004d6fd30 000000000000007f : 0000000000000008 0000000080050033 00000000000006f8 fffff80003095e58 : nt+0x6fb69 fffff80004d6fd38 0000000000000008 : 0000000080050033 00000000000006f8 fffff80003095e58 0000000000000000 : 0x7f fffff80004d6fd40 0000000080050033 : 00000000000006f8 fffff80003095e58 0000000000000000 0000000000000000 : 0x8 fffff80004d6fd48 00000000000006f8 : fffff80003095e58 0000000000000000 0000000000000000 0000000000000000 : 0x80050033 fffff80004d6fd50 fffff80003095e58 : 0000000000000000 0000000000000000 0000000000000000 0000000000000000 : 0x6f8 fffff80004d6fd58 0000000000000000 : 0000000000000000 0000000000000000 0000000000000000 0000000000000000 : nt+0x38e58 STACK_COMMAND: kb FOLLOWUP_IP: nt+70600 fffff800`030cd600 48894c2408 mov qword ptr [rsp+8],rcx SYMBOL_STACK_INDEX: 0 SYMBOL_NAME: nt+70600 FOLLOWUP_NAME: MachineOwner IMAGE_NAME: ntoskrnl.exe BUCKET_ID: WRONG_SYMBOLS Followup: MachineOwner ...................................................................... 0: kd !lmi nt Loaded Module Info: [nt] Module: ntkrnlmp Base Address: fffff8000305d000 Image Name: ntkrnlmp.exe Machine Type: 34404 (X64) Time Stamp: 4b88cfeb Sat Feb 27 00:55:23 2010 Size: 5dc000 CheckSum: 545094 Characteristics: 22 perf Debug Data Dirs: Type Size VA Pointer CODEVIEW 25, 19c65c, 19bc5c RSDS - GUID: {7E9A3CAB-6268-45DE-8E10-816E3080A3B7} Age: 2, Pdb: ntkrnlmp.pdb CLSID 4, 19c658, 19bc58 [Data not mapped] Image Type: FILE - Image read successfully from debugger. ntkrnlmp.exe Symbol Type: PDB - Symbols loaded successfully from symbol server. d:\debugsymbols\ntkrnlmp.pdb\7E9A3CAB626845DE8E10816E3080A3B72\ntkrnlmp.pdb Load Report: public symbols , not source indexed d:\debugsymbols\ntkrnlmp.pdb\7E9A3CAB626845DE8E10816E3080A3B72\ntkrnlmp.pdb 0: kd !analyze -v * Bugcheck Analysis * * UNEXPECTED_KERNEL_MODE_TRAP (7f) This means a trap occurred in kernel mode, and it's a trap of a kind that the kernel isn't allowed to have/catch (bound trap) or that is always instant death (double fault). The first number in the bugcheck params is the number of the trap (8 = double fault, etc) Consult an Intel x86 family manual to learn more about what these traps are. Here is a portion of those codes: If kv shows a taskGate use .tss on the part before the colon, then kv. Else if kv shows a trapframe use .trap on that value Else .trap on the appropriate frame will show where the trap was taken (on x86, this will be the ebp that goes with the procedure KiTrap) Endif kb will then show the corrected stack. Arguments: Arg1: 0000000000000008, EXCEPTION_DOUBLE_FAULT Arg2: 0000000080050033 Arg3: 00000000000006f8 Arg4: fffff80003095e58 Debugging Details: BUGCHECK_STR: 0x7f_8 CUSTOMER_CRASH_COUNT: 1 DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT PROCESS_NAME: System CURRENT_IRQL: 2 LAST_CONTROL_TRANSFER: from fffff800030ccb69 to fffff800030cd600 STACK_TEXT: fffff80004d6fd28 fffff800030ccb69 : 000000000000007f 0000000000000008 0000000080050033 00000000000006f8 : nt!KeBugCheckEx fffff80004d6fd30 fffff800030cb032 : 0000000000000000 0000000000000000 0000000000000000 0000000000000000 : nt!KiBugCheckDispatch+0x69 fffff80004d6fe70 fffff80003095e58 : 0000000000000000 0000000000000000 0000000000000000 0000000000000000 : nt!KiDoubleFaultAbort+0xb2 fffff880089efc60 0000000000000000 : 0000000000000000 0000000000000000 0000000000000000 0000000000000000 : nt!SeAccessCheckFromState+0x58 STACK_COMMAND: kb FOLLOWUP_IP: nt!KiDoubleFaultAbort+b2 fffff800`030cb032 90 nop SYMBOL_STACK_INDEX: 2 SYMBOL_NAME: nt!KiDoubleFaultAbort+b2 FOLLOWUP_NAME: MachineOwner MODULE_NAME: nt IMAGE_NAME: ntkrnlmp.exe DEBUG_FLR_IMAGE_TIMESTAMP: 4b88cfeb FAILURE_BUCKET_ID: X64_0x7f_8_nt!KiDoubleFaultAbort+b2 BUCKET_ID: X64_0x7f_8_nt!KiDoubleFaultAbort+b2 Followup: MachineOwner I tried running Rootkit Revealer but I don't think it works on x64 systems. Similarly Blacklight seems to have aged off. I'm running Sophos Anti-Rootkit now. So far so good...

  Read the article

• Graphics driver for ubuntu on dell latitude XT

  - by marc.riera

  we have a laptop (dell latitude xt) on our company, and we would like to install ubuntu on it. windows 7 works fine out of the box, so the hardware is fine. since this laptop has a touchscreen we just installed ubuntu 10.10 netbook edition 32x. But, we do not manage to enable the touchscreen, neither the vga graphic drivers. this is the output from lspci, if somebody cares. 00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 7930 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS7932 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc Device 7934 00:06.0 PCI bridge: ATI Technologies Inc RS7936 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc Device 7937 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Xpress 1250 03:01.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 03:01.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 03:01.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0b:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 03) I've tryied to install ati drivers 9.3 , which I downloaded and installed, unpacked and installed, builded and installed, but nothing worked. Looks like the latests version is just accepted to work on jaunty 9.04, so they are kind of old. what else I can do? thanks. Marc Information added: lsusb and lspci -n |grep 01:05.0 sysop@wl083517:~$ lspci -n |grep 01:05.0 01:05.0 0300: 1002:7942 sysop@wl083517:~$ lsusb Bus 006 Device 002: ID 413c:8138 Dell Computer Corp. Wireless 5520 Voda I Mobile Broadband (3G HSDPA) Minicard EAP-SIM Port Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 413c:8140 Dell Computer Corp. Wireless 360 Bluetooth Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1b96:0001 N-Trig Duosense Transparent Electromagnetic Digitizer Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 03f0:1807 Hewlett-Packard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sysop@wl083517:~$

  Read the article

• HID USB Very Strange Problem...

  - by Lasanha

  I realy hope some one can help me here cause i search all over the web and nothing comes up.. I allways used PS/2 KB and Mouse and a USB KeyPad (Genius ErgoMedia 500 Gaming Explorer) to play some games, mmorpg, fps, you named, very good whit 11 keys whit possible macros etc etc... Now it comes the problem, i have a USB mouse that have 4 extra buttons, and i need more button, i love buttons.. Well, i plug in the USB mouse and disconectes de PS/2. Everything is ok until i toutch the mouse. If i do so, the ErgoMedia goes off, then on, then i mouse the mouse or press a button and all over again. Yesterday i went buying a new mouse that i liked, a USB mouse too (NPlay whit macros and all that stuff 3600dpi...) Hoping the problem was only whit the other mouse, but no.. It does the exact same thing, ErgoMedia keeps disconecting and conecting everytime i toutch the mouse. What i allready did: Update drivers of both mouses Update drivers of ErgoMedia (no specific drivers(Windows based)) Update drivers of MB Chipset (Actualy no, cause it was up to date allready) Trying other USB Ports (4 Ports back, 4 Ports Front and even 1 Port in 16 card slot device) Disable the "Allows Windows to shut down the energy bla bla" thing in Device Setings. Look up in the Device Setings only apear a problem on the ergomedia (Human interface Device) when i move the damm mouse.. Using Everest to read behavier, everything normal, exepts the disconecting thing, but no errors. Not a power suply, only the ErgoMedia and the mouse are in the USBs, and i allready disable the 16 card reader whit one usb slot to see.. Clean the IRQ registry. Look the entire internet for a fix solution. Help others problems wile looking for a fix for me (Im not a pro but not a completly stupid) Talking to you beggin you to help me as a last resorce... Machine: Acer M3641 Core2Quad 64x Based OS Vista 64b 4GbRAM HD Audio and Graphics I realy hope some one out there knows a fix for this, maybe it´s a simple thing, so simple that i´m to stupid to see that.. Sorry for my bad inglish but i write lot of erros even in my language. Any help will be very welcome. Tanks for ur concern and atention ^^

  Read the article

• svchost.exe crash on wake up

  - by Serge

  Lately whenever I wake up my laptop from sleep I get a series of errors (generated by a host process failing) I haven't been able to figure out why this happens but I know which host process fails and was wondering if someone had some insight on why this keeps occuring 99% of the time when my laptop wakes up. here's the host process error Faulting application svchost.exe_SysMain, version 6.0.6001.18000, time stamp 0x47919291, faulting module ntdll.dll, version 6.0.6002.18005, time stamp 0x49e0421d, exception code 0xc0000006, fault offset 0x000000000005a02d, process id 0x1738, application start time 0x01cae656279b1010. and here are some services that fail because of that host The Windows Audio Endpoint Builder service terminated unexpectedly. It has done this 1 time(s). The following corrective action will be taken in 60000 milliseconds: Restart the service. The Wired AutoConfig service terminated unexpectedly. It has done this 1 time(s). The following corrective action will be taken in 0 milliseconds: Restart the service. The ReadyBoost service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 60000 milliseconds: Restart the service. The Human Interface Device Access service terminated unexpectedly. It has done this 1 time(s). The following corrective action will be taken in 120000 milliseconds: Restart the service. The Network Connections service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 100 milliseconds: Restart the service. The Program Compatibility Assistant Service service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 60000 milliseconds: Restart the service. The Superfetch service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 60000 milliseconds: Restart the service. Anyways I think you get the point, there are a few more. It got really annoying to wait for those services to restart so I created a batch file that does it automatically whenever the wlan stops I'm using Vista x64 on a Studio XPS 1640

  Read the article

• Customizing Fantacy Remote .INI file

  - by karthik

  I am using Fantacy Remote to remote view other machines. I have attached the default .INI file that Fantacy Remote uses. When i connect to a machine, the client user should not have mouse and keyboard access of the Remote machine. It should be a View only remote connection. And i want to make the Remote viewer screen to be in full screen mode, because i dont want the user to do anything with menubars of Fatancy remote. Because this is kiosk application. What should i change in configuration file [.ini] inorder to achieve the above ? Anyone who have used this software before, kindly help.. [APP] iVersion= 101 pcVersion=1.01a pcBuildDate=Mar 27 2009 [MAIN] iFirstSetup= 0 rcMain.rcLeft= 676 rcMain.rcTop= 378 rcMain.rcRight= 1004 rcMain.rcBottom= 672 iShowLog= 0 iMode= 1 [GENERAL] iTips= 1 iTrayAnimation= 1 iCheckColor= 1 iPriority= 1 iSsememcpy= 1 iAutoOpenRecv= 1 pcRecvPath=C:\Documents and Settings\karthikeyan\My Documents\Downloads\fremote101a\FantasyRemote101a\recv pcFileName=FantasyRemote iLanguage= 1 [SERVER] iAcceptVideo= 1 iAcceptAudio= 1 iAcceptInput= 1 iAutoAccept= 1 iAutoTray= 0 iConnectSound= 1 iEnablePassword= 0 pcPassword= pcPort=7902 [CLIENT] iAutoConnect= 0 pcPassword= pcDefaultPort=7902 [NETWORK] pcConnectAddr=192.168.1.1 pcPort=7902 [VIDEO] iEnable= 1 pcFcc=AMV3 pcFccServer= pcDiscription= pcDiscriptionServer= iFps= 30 iMouse= 2 iHalfsize= 0 iCapturblt= 0 iShared= 0 iSharedTime= 5 iVsync= 1 iCodecSendState= 1 iCompress= 2 pcPlugin= iPluginScan= 0 iPluginAspectW= 16 iPluginAspectH= 9 iPluginMouse= 1 iActiveClient= 0 iDesktop1= 1 iDesktop2= 2 iDesktop3= 0 iDesktop4= 3 iScan= 1 iFixW= 16 iFixH= 8 [AUDIO] iEnable= 1 iFps= 30 iVolume= 6 iRecDevice= 0 iPlayDevice= 0 pcSamplesPerSec=44100Hz pcChannels=2ch:Stereo pcBitsPerSample=16bit iRecBuffNum= 150 iPlayBuffNum= 4 [INPUT] iEnable= 1 iFps= 30 iMoe= 0 iAtlTab= 1 [MENU] iAlwaysOnTop= 0 iWindowMode= 0 iFrameSize= 4 iSnap= 1 [HOTKEY] iEnable= 1 key_IDM_HELP=0x00000070 mod_IDM_HELP=0x00000000 key_IDM_ALWAYSONTOP=0x00000071 mod_IDM_ALWAYSONTOP=0x00000000 key_IDM_CONNECT=0x00000072 mod_IDM_CONNECT=0x00000000 key_IDM_DISCONNECT=0x00000073 mod_IDM_DISCONNECT=0x00000000 key_IDM_CONFIG=0x00000000 mod_IDM_CONFIG=0x00000000 key_IDM_CODEC_SELECT=0x00000000 mod_IDM_CODEC_SELECT=0x00000000 key_IDM_CODEC_CONFIG=0x00000000 mod_IDM_CODEC_CONFIG=0x00000000 key_IDM_SIZE_50=0x00000074 mod_IDM_SIZE_50=0x00000000 key_IDM_SIZE_100=0x00000075 mod_IDM_SIZE_100=0x00000000 key_IDM_SIZE_200=0x00000076 mod_IDM_SIZE_200=0x00000000 key_IDM_SIZE_300=0x00000000 mod_IDM_SIZE_300=0x00000000 key_IDM_SIZE_400=0x00000000 mod_IDM_SIZE_400=0x00000000 key_IDM_CAPTUREWINDOW=0x00000077 mod_IDM_CAPTUREWINDOW=0x00000004 key_IDM_REGION=0x00000077 mod_IDM_REGION=0x00000000 key_IDM_DESKTOP1=0x00000078 mod_IDM_DESKTOP1=0x00000000 key_IDM_ACTIVE_MENU=0x00000079 mod_IDM_ACTIVE_MENU=0x00000000 key_IDM_PLUGIN=0x0000007A mod_IDM_PLUGIN=0x00000000 key_IDM_PLUGIN_SCAN=0x00000000 mod_IDM_PLUGIN_SCAN=0x00000000 key_IDM_DESKTOP2=0x00000078 mod_IDM_DESKTOP2=0x00000004 key_IDM_DESKTOP3=0x00000079 mod_IDM_DESKTOP3=0x00000004 key_IDM_DESKTOP4=0x0000007A mod_IDM_DESKTOP4=0x00000004 key_IDM_WINDOW_NORMAL=0x0000000D mod_IDM_WINDOW_NORMAL=0x00000004 key_IDM_WINDOW_NOFRAME=0x0000000D mod_IDM_WINDOW_NOFRAME=0x00000002 key_IDM_WINDOW_FULLSCREEN=0x0000000D mod_IDM_WINDOW_FULLSCREEN=0x00000001 key_IDM_MINIMIZE=0x00000000 mod_IDM_MINIMIZE=0x00000000 key_IDM_MAXIMIZE=0x00000000 mod_IDM_MAXIMIZE=0x00000000 key_IDM_REC_START=0x00000000 mod_IDM_REC_START=0x00000000 key_IDM_REC_STOP=0x00000000 mod_IDM_REC_STOP=0x00000000 key_IDM_SCREENSHOT=0x0000002C mod_IDM_SCREENSHOT=0x00000002 key_IDM_AUDIO_MUTE=0x00000073 mod_IDM_AUDIO_MUTE=0x00000004 key_IDM_AUDIO_VOLUME_DOWN=0x00000074 mod_IDM_AUDIO_VOLUME_DOWN=0x00000004 key_IDM_AUDIO_VOLUME_UP=0x00000075 mod_IDM_AUDIO_VOLUME_UP=0x00000004 key_IDM_CTRLALTDEL=0x00000023 mod_IDM_CTRLALTDEL=0x00000003 key_IDM_QUIT=0x00000000 mod_IDM_QUIT=0x00000000 key_IDM_MENU=0x0000007B mod_IDM_MENU=0x00000000 [OVERLAY] iIndicator= 1 iAlphaBlt= 1 iEnterHide= 0 pcFont=MS UI Gothic [AVI] iSound= 1 iFileSizeLimit= 100000 iPool= 4 iBuffSize= 32 iStartDiskSpaceCheck= 1 iStartDiskSpace= 1000 iRecDiskSpaceCheck= 1 iRecDiskSpace= 100 iCache= 0 iAutoOpen= 1 pcPath=C:\Documents and Settings\karthikeyan\My Documents\Downloads\fremote101a\FantasyRemote101a\avi [SCREENSHOT] iSound= 1 iAutoOpen= 1 pcPath=C:\Documents and Settings\karthikeyan\My Documents\Downloads\fremote101a\FantasyRemote101a\ss pcPlugin=BMP [CDLG_SERVER] mrcWnd.rcLeft= 667 mrcWnd.rcTop= 415 mrcWnd.rcRight= 1013 mrcWnd.rcBottom= 634 [CWND_CLIENT] miShowLog= 0 m_iOverlayLock= 0

  Read the article

• Expert iptables help needed?

  - by Asad Moeen

  After a detailed analysis, I collected these details. I am under a UDP Flood which is more of application dependent. I run a Game-Server and an attacker is flooding me with "getstatus" query which makes the GameServer respond by making the replies to the query which cause output to the attacker's IP as high as 30mb/s and server lag. Here are the packet details, Packet starts with 4 bytes 0xff and then getstatus. Theoretically, the packet is like "\xff\xff\xff\xffgetstatus " Now that I've tried a lot of iptables variations like state and rate-limiting along side but those didn't work. Rate Limit works good but only when the Server is not started. As soon as the server starts, no iptables rule seems to block it. Anyone else got more solutions? someone asked me to contact the provider and get it done at the Network/Router but that looks very odd and I believe they might not do it since that would also affect other clients. Responding to all those answers, I'd say: Firstly, its a VPS so they can't do it for me. Secondly, I don't care if something is coming in but since its application generated so there has to be a OS level solution to block the outgoing packets. At least the outgoing ones must be stopped. Secondly, its not Ddos since just 400kb/s input generates 30mb/s output from my GameServer. That never happens in a D-dos. Asking the provider/hardware level solution should be used in that case but this one is different. And Yes, Banning his IP stops the flood of outgoing packets but he has many more IP-Addresses as he spoofs his original so I just need something to block him automatically. Even tried a lot of Firewalls but as you know they are just front-ends to iptables so if something doesn't work on iptables, what would the firewalls do? These were the rules I tried, iptables -A INPUT -p udp -m state --state NEW -m recent --set --name DDOS --rsource iptables -A INPUT -p udp -m state --state NEW -m recent --update --seconds 1 --hitcount 5 --name DDOS --rsource -j DROP It works for the attacks on un-used ports but when the server is listening and responding to the incoming queries by the attacker, it never works. Okay Tom.H, your rules were working when I modified them somehow like this: iptables -A INPUT -p udp -m length --length 1:1024 -m recent --set --name XXXX --rsource iptables -A INPUT -p udp -m string --string "xxxxxxxxxx" --algo bm --to 65535 -m recent --update --seconds 1 --hitcount 15 --name XXXX --rsource -j DROP They worked for about 3 days very good where the string "xxxxxxxxx" would be rate-limited, blocked if someone flooded and also didn't affect the clients. But just today, I tried updating the chain to try to remove a previously blocked IP so for that I had to flush the chain and restore this rule ( iptables -X and iptables -F ), some clients were already connected to servers including me. So restoring the rules now would also block some of the clients string completely while some are not affected. So does this mean I need to restart the server or why else would this happen because the last time the rules were working, there was no one connected?

  Read the article

• CPU Lockup when loading folder of bookmarks in Firefox

  - by Gary M. Mugford

  I am running Firefox 3.6 on WinXPSP3 on a duo Core machine with 4G of memory. I am also running Avast! free anti-virus and ZoneAlarm free firewall, both latest versions. Within the last month, my service provider basically forced me to upgrade to a Docsis 3.0 compliant modem (offered me a deal I couldn't turn down). At that point, I also upgraded to FF3.6. Basically, I am not unhappy with many aspects of this switchover, EXCEPT, when I now load a folder of bookmarks (anywhere from 10 to 38) I get nothing like the load times I experienced a couple of months back. It's taking minutes rather than seconds. And the first bookmark in one of the folders, GMail, rarely loads before timing out. I have used the old trick of powering off the cable modem before my day's work. This used to fix 'load-lag' in the old days. I have switched from my ISP's DNS server to Google, OpenDNS and back. And nothing seems to work currently. It's not my DNS cache. That's been flushed and secondary computers also have the same issue when loading folders. I have watched the CPU usage and loading the folder will send VSMon (ZoneAlarm) usage over 40 percent, AVastSvc (Avast!) over 30 and Firefox will then push the needle to 100. There's a brief burst by SVCHost when the others falter in devouring cycles. Then everything subsides to single digits once the last tab is loaded. The only other nominal nastiness is VSMon ALWAYS hitting 50 percent when ANY program starts downloading content from the internet. If I shutdown ZoneAlarm (and VSMon with it), the same slow loading takes place, but this time System is running 50% plus, again driving the usage to 100 per cent. I have my doubts FF3.6 vs FF3.5 is an issue, since the other computers are still running 3.5 and suffer the same issue. Those computers are on, but inactive, most of the time, being backups. Obviously, when the CPU hits 100, I can't do much of anything in FireFox OR in other programs. Video play through WMPC or VLC is extremely choppy, although it doesn't seem to affect the audio. Any ideas what I can try next? Thanks, GM

  Read the article

• CPU overheating after cleaning it

  - by Roberts

  I wanted to clean my computer CPU heatsink and fan itself, because the temperature is not what I wanted. About (50C ~ 70C). I have Intel Core 2 Duo E4300 @1.8 GHz (LGA775). The heatsink wasn't so scary filled with dust but I wanted to clean it anyway. I didn't know how to get heatsink with fan from the socket. So after 25 minutes I've figured it out. But I didn't know how to get it back on so I spent a lot time getting out the motherboard from the case. The fan and heatsink... The case and all components are clear of dust. (I'm tired now). Then I put all back just the way it was, well did few things on cable management. But the problem was that I didn't know how to connect front audio connectors. I had Windows XP hibernated. So I started the PC and everything was normal, except CMOS memory was clear. I configured the BIOS just the way it was and while I was doing that I saw about 58C CPU temperature and fan at 1789 RPM. Restarted the computer with new settings applied. But Windows halted with Blue Screen (I forgot what error it was but something with KERNEL). Restarted the PC and deleted hibernation session and everything was back normal. But couldn't record any sound from front panel microphone. The problem was that I messed ground wire with mic. Again after fixing it I turned computer on. No problems. The fan currently is noisy and temperature was 78C. The temperature before was 55C - 60C at idle. Now it's about 60C. If I do something then temperature raises to 79C. While speaking in skype the temperature was 82C. Could this problem occur because of the thermal grease (it's old and never replaced)? Edit The problem wasn't in thermal paste (because I didn't touch it). The problem was that I installed heatsink wrong. Now instead of regular 60C CPU temperature the CPU is at 48C (cool).

  Read the article

• Scoping a home dev server

  - by AbhikRK

  Hi. I’m looking to build a multi-purpose home development server. In this post, I’m looking to outline what I want from such a system, and the ‘why’s of it, to some limited extent, and finally, some rudiments of how I’m looking to go about that. I’m mostly a developer, with just about some sysadmin familiarity. So, please excuse, correct me, and suggest on any ignorance which would come across in the following ;-) It will serve the following goals to start with:- NAS (Looking at using ZFS) Source control repo e.g Git server Database e.g MySQL server Continuous Integration e.g Hudson server Other stuff as and when they come up e.g RabbitMQ etc A development sandbox to play around with new stuff I want to achieve a high uptime for 2-5 as much as possible. They should run as independent services and with minimal maintenance. (e.g TurnKey Linux appliances) I’m thinking of running them as individual Xen DomUs. Then, maybe the NAS can be a Dom0 and 6 can be another DomU. The User for this would be mostly me. I can see 2-4 being sometimes used by 2-3 users, but that would be infrequent. I’m looking for a repeatable setup. Ideally I’d like to automate this setup through Chef or Puppet or something similar. Once everything runs, I want to be able to ssh/screen/tmux into 1-6 from my laptop or any other computer on the LAN/on-the-go. My queries are:- Is putting 1-6, all of them on a single box, a good idea? If so, what kind of hardware should I be looking at, for a low-cost, low-power setup? Although not at present, but in future I might be looking at adding audio/media servers to the mix. Would that impact the answers to 1? I have an old Pentium 3 and 810e motherboard combination. Is there any way I could put it to use? I had a look at the Sheevaplug, and was wondering if I could split off the NAS on its own using that. But ruled it out preliminarily due to its reported heating issues. Is it something i should still consider? Thanks in advance

  Read the article

• Scoping a home dev server

  - by AbhikRK

  Hi. I’m looking to build a multi-purpose home development server. In this post, I’m looking to outline what I want from such a system, and the ‘why’s of it, to some limited extent, and finally, some rudiments of how I’m looking to go about that. I’m mostly a developer, with just about some sysadmin familiarity. So, please excuse, correct me, and suggest on any ignorance which would come across in the following ;-) It will serve the following goals to start with:- NAS (Looking at using ZFS) Source control repo e.g Git server Database e.g MySQL server Continuous Integration e.g Hudson server Other stuff as and when they come up e.g RabbitMQ etc A development sandbox to play around with new stuff I want to achieve a high uptime for 2-5 as much as possible. They should run as independent services and with minimal maintenance. (e.g TurnKey Linux appliances) I’m thinking of running them as individual Xen DomUs. Then, maybe the NAS can be a Dom0 and 6 can be another DomU. The User for this would be mostly me. I can see 2-4 being sometimes used by 2-3 users, but that would be infrequent. I’m looking for a repeatable setup. Ideally I’d like to automate this setup through Chef or Puppet or something similar. Once everything runs, I want to be able to ssh/screen/tmux into 1-6 from my laptop or any other computer on the LAN/on-the-go. My queries are:- Is putting 1-6, all of them on a single box, a good idea? If so, what kind of hardware should I be looking at, for a low-cost, low-power setup? Although not at present, but in future I might be looking at adding audio/media servers to the mix. Would that impact the answers to 1? I have an old Pentium 3 and 810e motherboard combination. Is there any way I could put it to use? I had a look at the Sheevaplug, and was wondering if I could split off the NAS on its own using that. But ruled it out preliminarily due to its reported heating issues. Is it something i should still consider? Thanks in advance Have posted this question previously on SuperUser but no responses yet. So was wondering if this is a more apt forum for this.

  Read the article

• Why are my httpd mpm_prefork processes being reaped so quickly?

  - by Dan Pritts

  We've got a system running RHEL6, x64. We are using a local installation of apache 2.2.22 from source. we serve primarily: mod_perl applications (with a local installation of perl 5.16.0) tomcat applications proxied with mod_jk Here is some context; the main question is below. All of this talks to an Oracle backend. We are having issues with Oracle becoming unresponsive. We think this is because we're hitting the maximum process limit in oracle. We've upped the process limit, but now we are hitting memory pressure on the oracle server. We have tons of oracle sessions sitting idle. I can trace a bunch of them back to the httpd processes. We have mod_perl's Apache::DBI start up a new connection to the database with each httpd child that's spawned. We are concerned that these are not always getting closed out properly when the httpd's exit...and the httpd's are exiting very frequently. I know that it would be good to modify the mod_perl applications to use some better form of db connection pooling; we plan to pursue that but would like to solve our immediate problem sooner. So here's the main question. We are using the prefork MPM. The apache child processes are lasting at most a few minutes. Log analysis shows that each one is serving fewer than 50 clients before exiting; the last request each child serves is OPTIONS * HTTP/1.0 on some sort of internal connection; I'm under the impression that this is a "ping" from the master process. I've adjusted the MPM config as follows. I didn't want to raise MinSpareServers too high, because, after all, i'm trying to minimize the number of sessions to oracle. MinSpareServers 5 MaxSpareServers 30 MaxClients 150 MaxRequestsPerChild 10000 Right now we're serving 250-300 requests per minute. We've got 21 httpd's running, the eldest (other than the master, owned by root) being 3 minutes old. This rate of reaping of the apache children really seems excessive. What could be causing it? Apache was built with: $ ./configure --prefix=/opt/apache --with-ssl=/usr/lib --enable-expires --enable-ext-filter --enable-info --enable-mime-magic --enable-rewrite --enable-so --enable-speling --enable-ssl --enable-usertrack --enable-proxy --enable-headers --enable-log-forensic Apache config info: % /opt/apache/bin/httpd -V Server version: Apache/2.2.22 (Unix) Server built: Jul 23 2012 22:30:13 Server's Module Magic Number: 20051115:30 Server loaded: APR 1.4.5, APR-Util 1.4.1 Compiled using: APR 1.4.5, APR-Util 1.4.1 Architecture: 64-bit Server MPM: Prefork threaded: no forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="/opt/apache" -D SUEXEC_BIN="/opt/apache/bin/suexec" -D DEFAULT_PIDLOG="logs/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="logs/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="conf/mime.types" -D SERVER_CONFIG_FILE="conf/httpd.conf" modules are compiled into apache rather than shared libs: % /opt/apache/bin/httpd -l Compiled in modules: core.c mod_authn_file.c mod_authn_default.c mod_authz_host.c mod_authz_groupfile.c mod_authz_user.c mod_authz_default.c mod_auth_basic.c mod_ext_filter.c mod_include.c mod_filter.c mod_log_config.c mod_log_forensic.c mod_env.c mod_mime_magic.c mod_expires.c mod_headers.c mod_usertrack.c mod_setenvif.c mod_version.c mod_proxy.c mod_proxy_connect.c mod_proxy_ftp.c mod_proxy_http.c mod_proxy_scgi.c mod_proxy_ajp.c mod_proxy_balancer.c mod_ssl.c prefork.c http_core.c mod_mime.c mod_status.c mod_autoindex.c mod_asis.c mod_info.c mod_cgi.c mod_negotiation.c mod_dir.c mod_actions.c mod_speling.c mod_userdir.c mod_alias.c mod_rewrite.c mod_so.c One final note - the red hat httpd, apr, and perl packages are all installed, but ldd shows that none of those libraries are linked with the running httpd.

  Read the article

• Wiimote accelerometer input on Windows? (in 2013 - Glovepie alternative?)

  - by user568458

  There were a few options for getting accelerometer input into Windows using a Nintendo Wiimote. As of mid 2013, these projects seem to be dead, corrupted with malware, or both. Are there any tools out there that can do this that are still available (and not full of malware)? Quick roundup of the options that used to exist, or that still exist but aren't suitable: Glovepie, which used to be the most recommended option, appears to be dead: it's own website hacked, its creator's googlepages page full of strange stuff that sounds like hacker-humour about the end of the world... (I'd rather not link to them, very dubious stuff...), and lots of forum threads asking if it's a dead project with comments along the lines of "I heard that the author intends to return to it" dated 2011... Wiiuse seems to be dead: its sourceforge page simply says "Error.", its own website has turned into a squatter page. There apparently was an extension for Autohotkey that allowed Wiimote input, but I've seen warnings that this too is now full of malware (see final commentin above link) Everything else I can find about using Wiimotes as input on Windows - for example, Johnny Lee Cheng's work - seems to be exclusively about using infrared or sensor bar, or tied to a specific purpose (e.g. FPS gaming). My main interest is in the accelerometer, and buttons if possible (although something that supports the IR stuff too would be ideal). Is there anything that works for getting Wiimote accelerometer input into Windows that is reliable and not a malware-fest? If anyone's interested in "Why?", it's to use the Wiimote as an audio / midi controller: to use movement, pitch, roll etc to modulate lots of different sound variables at once with one hand. Wiimotes are great for this, and Glovepie used to be the standard way to make this work (e.g. see for example this tutorial, and this one, ignore the unrelated video; I've also seen musicians using wiimote/glovepie setups at gigs, creating some really unique sounds). As of 2013, however, Glovepie seems to be a dead and thoroughly hacked project, sadly. Is there anything else? With or without MotionPlus is fine (with would be better). If anyone knows of any worthy alternatives to Wiimotes in terms of price and quality that can be made to work with a PC, that would also be great: but in my research I coulnd't find any (here's a link to someone reaching the same conclusion). found some potentially relevant stuff here, not had time to test any of it yet though - http://stackoverflow.com/questions/2984450/using-accelerometer-in-wiimote-for-physics-practicals

  Read the article

• Win7 x64 unresponsive for a minute or so. HD failing?

  - by Gaia

  On a fully updated Win7 x64, every so often the system stalls for a minute or so. This has been going on for a couple months now. By stalling I mean the mouse responds and I can move windows around, but any window, any program, that is open becomes whiteish when I select it AND any new programs will not open. It doesn't matter what kind of program it is. When the stall stops all clicks I made (open new programs for example) take effect. Nothing shows up consistently (as in every time this happens) in the event log. Today though I was able to find something, but it doesn't reveal much other than the "system was unresponsive". It's a 7009 for "A timeout was reached (30000 milliseconds) while waiting for the Windows Error Reporting Service service to connect." It doesn't matter if I have any USB devices plug-in or not. I've ran Microsoft Security Essentials and Malwarebytes. While the machine is unresponsive, I've noticed that Drive D (the other partition on the single internal HD in this laptop) is displayed like this in explorer. This never occurs with Drive C or any other drive on the machine. . SMART report for the physical drive: Read benchmark by HD Tune 5 Pro, probably the most telling piece of the puzzle. Isn't this alone enough to see there is a problem with the drive, regardless of whether the unresponsiveness is caused by such purported problem? Here is a short hardware report: Computer: LENOVO ThinkPad T520 CPU: Intel Core i5-2520M (Sandy Bridge-MB SV, J1) 2500 MHz (25.00x100.0) @ 797 MHz (8.00x99.7) Motherboard: LENOVO 423946U Chipset: Intel QM67 (Cougar Point) [B3] Memory: 8192 MBytes @ 664 MHz, 9.0-9-9-24 - 4096 MB PC10600 DDR3 SDRAM - Samsung M471B5273CH0-CH9 - 4096 MB PC10600 DDR3 SDRAM - Patriot Memory (PDP Systems) PSD34G13332S Graphics: Intel Sandy Bridge-MB GT2+ - Integrated Graphics Controller [D2/J1/Q0] [Lenovo] Intel HD Graphics 3000 (Sandy Bridge GT2+), 3937912 KB Drive: ST320LT007, 312.6 GB, Serial ATA 3Gb/s Sound: Intel Cougar Point PCH - High Definition Audio Controller [B2] Network: Intel 82579LM (Lewisville) Gigabit Ethernet Controller Network: Intel Centrino Advanced-N 6205 AGN 2x2 HMC OS: Microsoft Windows 7 Professional (x64) Build 7601 The drive less than 1 year old. Do I have a defective drive? Seagate Tools diag says there is nothing wrong with the drive... UPDATE: I noticed that the windows error reporting service entered the running state then the stopped state and the space between the two events was exactly 2 minutes. Which error it was trying to report I don't know. I check the "Reliability Monitor" and it shows no errors to be reported. I've disabled the windows error reporting service to see if the problem stops.

  Read the article

• ffmpeg video4linux2 at specified resolution

  - by wim

  When I'm trying to record a clip from my webcam, using: ffmpeg -f video4linux2 -s 640x480 -i /dev/video0 /tmp/spam.avi I get annoying problem with very low resolution video, and there is a message from ffmpeg saying: [video4linux2,v4l2 @ 0x2bff3e0] The V4L2 driver changed the video from 800x600 to 176x144 I have tried not specifying -s, or trying other sizes like 800x600, and always it forces me back to 176x144. Why is this and how can I prevent it? My webcam is one of those Logitech 9000 Pro, I know it supports better resolutions than this and I can see with v4l2-ctl --list-formats-ext that it goes up to at least 800x600. edit: complete console output follows wim@wim-desktop:~$ ffmpeg -f video4linux2 -s 640x480 -i /dev/video0 /tmp/spam.avi ffmpeg version git-2012-11-20-70c0f13 Copyright (c) 2000-2012 the FFmpeg developers built on Nov 21 2012 00:09:36 with gcc 4.6 (Ubuntu/Linaro 4.6.3-1ubuntu5) configuration: --enable-gpl --enable-libfaac --enable-libfdk-aac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libvpx --enable-x11grab --enable-libx264 --enable-nonfree --enable-version3 libavutil 52. 8.100 / 52. 8.100 libavcodec 54. 73.100 / 54. 73.100 libavformat 54. 37.100 / 54. 37.100 libavdevice 54. 3.100 / 54. 3.100 libavfilter 3. 23.101 / 3. 23.101 libswscale 2. 1.102 / 2. 1.102 libswresample 0. 17.100 / 0. 17.100 libpostproc 52. 2.100 / 52. 2.100 [video4linux2,v4l2 @ 0x37a33e0] The V4L2 driver changed the video from 640x480 to 176x144 [video4linux2,v4l2 @ 0x37a33e0] Estimating duration from bitrate, this may be inaccurate Input #0, video4linux2,v4l2, from '/dev/video0': Duration: N/A, start: 37066.740548, bitrate: 6082 kb/s Stream #0:0: Video: rawvideo (YUY2 / 0x32595559), yuyv422, 176x144, 6082 kb/s, 15 tbr, 1000k tbn, 15 tbc File '/tmp/spam.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to '/tmp/spam.avi': Metadata: ISFT : Lavf54.37.100 Stream #0:0: Video: mpeg4 (FMP4 / 0x34504D46), yuv420p, 176x144, q=2-31, 200 kb/s, 15 tbn, 15 tbc Stream mapping: Stream #0:0 -> #0:0 (rawvideo -> mpeg4) Press [q] to stop, [?] for help frame= 95 fps= 22 q=2.0 Lsize= 88kB time=00:00:13.86 bitrate= 51.8kbits/s video:77kB audio:0kB subtitle:0 global headers:0kB muxing overhead 13.553706%

  Read the article

• 404 Error on a file that exists?

  - by Abs

  Hello all, A script makes a GET request to my URL like so: http://mydomain.com/cgi-bin/uu_ini_status_audios.pl?tmp_sid=b742be1d131c4d32237a9f1fcdca659e&rnd_id=0.2363453360320319 However, I get a 404 returned straight away: The requested URL /cgi-bin/uu_ini_status_audios.pl was not found on this server. But that script exists on my server, I can see the file! It has the correct permissions (I gave it a 777 to be sure). It is also owned by my apache user and its in the group apache. What am I missing?? Thanks for any help on this! Update I thought it would have been a htaccess (rewrite) but I don't think it is anymore. I tried putting a index.php file in there and try to access it via my URL but I can't even do that! I tried this: http://mydoamin.com/cgi-bin/index.php - same 404 error! I get this in myerror log: [Tue Sep 14 14:42:49 2010] [error] [client xx.xxx.xx.xxx] script not found or unable to stat: /var/www/vhosts/mydomain.com/cgi-bin Access_log file: xx.xxx.xx.xxx - - [14/Sep/2010:14:48:25 +0200] "GET /cgi-bin/index.php HTTP/1.1" 404 475 "-" "Mozilla/5.0 (Windows; U; Windows NT 6.0; en-US; rv:1.9.2.9) Gecko/20100824 Firefox/3.6.9 (.NET CLR 3.5.30729)" Update 2 My htaccess file: <IfModule mod_rewrite.c> RewriteEngine On RewriteRule ^blog/ - [L] RewriteCond %{HTTP_HOST} ^www\.mydomain\.com$ [NC] RewriteRule ^(.*)$ http://mydomain.com/$1 [R=301,L] RewriteRule ^search/(.*)/(.*)/(.*)/(.*) /search.php?searchfor=$1&sortby=$2&page=$3&searchterm=$4 RewriteRule ^confirmemail/(.*) /confirmemail.php?code=$1 RewriteRule ^resetpassword/(.*) /resetpassword.php?code=$1 RewriteRule ^resendconfirmation/(.*) /resendconfirmation.php?userid=$1 RewriteRule ^categories/ /categories.php RewriteRule ^([-_~*a-zA-Z0-9]+)(\/)?$ /memberprofile.php?username=$1 RewriteRule ^browse/audios/(.*)/(.*)/(.*)/(.*) /audios.php?sortby=$1&filter=$2&page=$3&title=$4 RewriteRule ^browse/categories/audios/(.*)/(.*)/(.*)/(.*) /categoryaudios.php?sortby=$1&filter=$2&page=$3&title=$4 RewriteRule ^audios/(.*)/(.*) /playaudio.php?audioid=$1&title=$2 RewriteRule ^download/audio/(.*)/(.*) /downloadaudio.php?AUDIOID=$1&title=$2 RewriteRule ^members/audios/(.*)/(.*) /memberaudios.php?pid=$1&username=$2 RewriteRule ^syndicate/audios/(.*)/(.*) /syndicateaudios.php?filter=$1&title=$2 </IfModule> Update 3 [root@smydomain ~]# ls -la /var/www/vhosts/mydoamin.com/httpdocs/cgi-bin/ total 60 drwxr-xr-x 3 apache root 4096 Sep 14 14:37 . drwxr-x--- 20 som psaserv 4096 Sep 14 14:40 .. drwxr-xr-x 2 apache root 4096 Sep 7 03:01 configs -rwxrwxrwx 1 apache root 4 Sep 14 14:37 index.php -rwxrwxrwx 1 apache apache 6520 Sep 7 03:01 uu_ini_status_audios.pl -rwxr-xr-x 1 apache root 3215 Sep 7 03:01 uu_lib_audios.pl -rwxr-xr-x 1 apache root 30249 Sep 7 03:01 uu_upload_audios.pl

  Read the article

• Problems with Windows XP Plug and Play devices, maybe relating to MSVCR71.dll

  - by Richard

  I believe this question is unanswered as of now so I appologize if I've overlooked it. I have been having trouble some external devices with windows recently and I'm trying my darnedest to get to the bottom of it. At first, my Zero Tension USB mouse would stop working...as in the laser in the bottom of it would be on and would register movement, but the mouse on the screen wouldn't budge even an inch. At first this would happen randomly and then it would correct itself. As time went on, it became more and more frequent. At some point, the computer would make the "doo doo" sound of plugging or unplugging a USB device when the mouse stopped/started working. I dealt with it for a while and usually if I rebooted my machine, the mouse would work again for a day or two. As more time has gone on, the computer fully does not recognize the mouse AT ALL...I have another mouse that I use with the computer that works just fine and cannot seem to figure out why my Zero Tension mouse has failed. I tried plugging the Zero Tension mouse into my Mac and low and behold, it works without hesitation and never stops on me... Needless to say, I am stumped about this. I figured because I had another mouse I could deal with the loss of my fancy one for now...until my speakers stopped being recognized. I have a set of Logitec speakers that I have plugged into my sound card. Again, every now and again the audio devices would cease to be recognized by my computer, but a reboot would fix the problem. Now my speakers do not work at all with my computer and I feel like it's time to ask for help. My computer seems to be having a neural shutdown...where I can plug in devices and the computer doesn't seem to notice anything wrong, but none of the devices work. I hope this doesn't get any worse! Please help! Also, on a potentially (un)related note, when I start up my machine I get the message "This application has failed to start because Msvcp71.dll was not found. Re-installing the application may fix this problem." in reference to qbupdate.exe I don't know if that DLL being messed up has anything to do with my mouse or speakers, but I figure it might...anyway, thanks in advance for an answer and let me know if I need to clarify anything. Let me sum up: Zero Tension Mouse gradually stopped working Logitec Speakers gradually stopped working MSVCR71.dll seems to be messed up I don't know if any of those are related but any help would be much appreciated

  Read the article

• file corruption on read/write 2.6.32-22-server (happens across many kernels)

  - by Jonathan

  Hi Guys, I'm having an issue where after the server has been up for a period of time (~week/few days) the server will start reading corrupt data. For instance when I run a sha1sum of a file after a fresh boot it remains the same. However after a while I will start to get segfaults and from then on whenever I read this file I get a different sha1sum. I've checked S.M.A.R.T with long tests and I've run an extended memtest86+(12 passes) My lspci is as follows: 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon HD 3300 Graphics 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller 02:00.0 Ethernet controller: Atheros Communications Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller (rev b0) 03:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. Device 3403 I could really use some help on this, do you have any idea what could cause this? It's really frustrating me as it seems to trigger entirely randomly and will not go away until I reboot. I'm also use KVM for virtualization as well as MD for software RAID on this server and the processor is a Phenom II X4 965. I don't believe it's the software raid however as this affects files also hosted on non-raid partitions so I don't know.

  Read the article

< Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249  | Next Page >