Search Results

Search found 6845 results on 274 pages for 'all systems'.

Page 243/274 | < Previous Page | 239 240 241 242 243 244 245 246 247 248 249 250  | Next Page >

• network is not available even when cisco vpn client is connected. wrong route?

  - by javapowered

  I'm using Vodafone 3G modem. I've disabled other network devices in the system (ethernet, wifi, wimax) turned off firewall and antivirus. cisco vpn client connects successfully but I still can not access computer 192.168.147.120 (as well as any other computer from network). Any suggestions are welcome as I don't know what to do. ipconfig /all and route print commands (translated to english): Microsoft Windows [Version 6.1.7601] (C) Microsoft Corporation (Microsoft Corp.), 2009. All rights reserved. C: \ Users \ Oleg> ipconfig / all IP Configuration for Windows The name of the computer. . . . . . . . . : OlegPC The primary DNS-suffix. . . . . . : Node Type. . . . . . . . . . . . . : Hybrid IP-routing is enabled. . . . : No WINS-proxy enabled. . . . . . . : No Ethernet adapter Local Area Connection 4: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Cisco Systems VPN Adapter Physical Address. . . . . . . . . 00-05-9A-3C-78-00 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Local IPv6-address channel. . . : Fe80:: c073: 41b2: 852f: eb87% 26 (Preferred) IPv4-address. . . . . . . . . . . . : 10.53.127.204 (Preferred) The subnet mask. . . . . . . . . . : 255.0.0.0 Default Gateway. . . . . . . . . : IAID DHCPv6. . . . . . . . . . . : 536872346 DUID the client DHCPv6. . . . . . . 00-01-00-01-14-6F-4C-8D-60-EB-69-85-10-2D DNS-servers. . . . . . . . . . . : Fec0: 0:0: ffff:: 1% 1 fec0: 0:0: ffff:: 2% 1 fec0: 0:0: ffff:: 3% 1 NetBios over TCP / IP. . . . . . . . : Disabled Adapter mobile broadband connection through a broadband adapter mobile communications: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Vodafone Mobile Broadband Network Adapter (Huawei) Physical Address. . . . . . . . . 58-2C-80-13-92-63 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv4-address. . . . . . . . . . . . : 10.229.227.77 (Preferred) The subnet mask. . . . . . . . . . : 255.255.255.252 Default Gateway. . . . . . . . . : 10.229.227.78 DNS-servers. . . . . . . . . . . : 163.121.128.134 212.103.160.18 NetBios over TCP / IP. . . . . . . . : Disabled Tunnel adapter isatap. {737FF02E-D473-4F91-840E-2A4DD293FC12}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 3 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter isatap. {EF585226-5B07-4446-A5A4-CB1B8E4B13AC}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 4 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv6-address. . . . . . . . . . . . : 2001:0:4137:9 e76: ea: b77: f51a: 1cb2 (Basically d) Local IPv6-address channel. . . : Fe80:: ea: b77: f51a: 1cb2% 16 (Preferred) Default Gateway. . . . . . . . . ::: NetBios over TCP / IP. . . . . . . . : Disabled C: \ Users \ Oleg> route print ================================================== ========================= List of interfaces 26 ... 00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter 23 ... 58 2c 80 13 92 63 ...... Vodafone Mobile Broadband Network Adapter (Huawei) 1 ........................... Software Loopback Interface 1 19 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 3 20 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 4 16 ... 00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface ================================================== ========================= IPv4 Route Table ================================================== ========================= Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.229.227.78 10.229.227.77 296 10.0.0.0 255.0.0.0 On-link 10.53.127.204 286 10.6.93.21 255,255,255,255 10.0.0.1 10.53.127.204 100 10.13.50.12 255,255,255,255 10.0.0.1 10.53.127.204 100 10.53.8.0 255.255.252.0 10.0.0.1 10.53.127.204 100 10.53.127.204 255.255.255.255 On-link 10.53.127.204 286 10.53.128.0 255.255.248.0 10.0.0.1 10.53.127.204 100 10.53.148.0 255,255,255,240 10.0.0.1 10.53.127.204 100 10.53.148.16 255,255,255,240 10.0.0.1 10.53.127.204 100 10.229.227.76 255.255.255.252 On-link 10.229.227.77 296 10.229.227.77 255.255.255.255 On-link 10.229.227.77 296 10.229.227.79 255.255.255.255 On-link 10.229.227.77 296 10.255.255.255 255.255.255.255 On-link 10.53.127.204 286 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.147.0 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.147.96 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,112 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,128 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,144 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,224 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.214.0 255.255.255.0 10.0.0.1 10.53.127.204 100 192.168.215.0 255.255.255.0 10.0.0.1 10.53.127.204 100 194.247.133.19 255,255,255,255 10.0.0.1 10.53.127.204 100 213,247,231,194 255,255,255,255 10.229.227.78 10.229.227.77 100 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.229.227.77 296 224.0.0.0 240.0.0.0 On-link 10.53.127.204 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.229.227.77 296 255.255.255.255 255.255.255.255 On-link 10.53.127.204 286 ================================================== ========================= Persistent Routes: None IPv6 Route Table ================================================== ========================= Active Routes: If Metric Network Destination Gateway 16 58:: / 0 On-link 1306:: 1 / 128 On-link 16 58 2001:: / 32 On-link 16 306 2001: 0:4137:9 e76: ea: b77: f51a: 1cb2/128 On-link 16 306 fe80:: / 64 On-link 26 286 fe80:: / 64 On-link 16 306 fe80:: ea: b77: f51a: 1cb2/128 On-link 26 286 fe80:: c073: 41b2: 852f: eb87/128 On-link 1306 ff00:: / 8 On-link 16 306 ff00:: / 8 On-link 26 286 ff00:: / 8 On-link ================================================== ========================= Persistent Routes: None C: \ Users \ Oleg>

  Read the article

• Pros/Cons of switching from Exchange to GMail

  - by Brent

  We are a medium-large non-profit company, with around 1000 staff and volunteers, and have been using MS Exchange (currently 2003) for our mail system for years. I recently attended a Google conference where they were positing that "Cloud computing is the way of the future", and encouraging us to switch from doing our own email with Exchange, to using GMail and Google Apps for everything. Additionally, one of our departments has been pushing from inside to do this transition within their own department, if not throughout the entire organization. I can definitely see some benefits - such as: Archive space - we never seem to have the space our users want, and of course, the more we get, the more we have to back up OS Agnostic - Exchange is definitely built for windows, and with mac and linux users on the rise, these users increasingly demand better tools / support. Google offers this. Better archiving - potential of e-discovery, that doesn't exist in a practical way with our current setup. Switching would relieve us of a fair bit of server administration, give more options to our end users, and free up the server resources we are now using for Exchange. Our IT department wants to be perceived as providing up-to-date solutions to technical problems, and this change would definitely provide such an image. Google's infrastructure is obviously much more robust than ours, and they employ some of the world's best security and network experts. However, there are also some serious drawbacks: We would be essentially outsourcing one of our mission-critical systems to a 3rd party The switch would inevitably involve Google Apps and perhaps more as well. That means we would have a-lot more at the mercy of a single (potentially weak) password. (is there a way to make this more secure using a password plus physical key of some sort??) Our data would not remain under our roof - or even in our country (Canada). This obviously has plusses on the Disaster Recovery side, but I think there are potential negatives on the legal side. I can't imagine that somebody as large as Google would be as responsive as we would want with regard to non-critical issues such as tracing missing emails, etc. (not sure how much access we would have to basic mail logs - for instance) Can anyone help me evaluate this decision? What issues am I overlooking? What experiences have you had with this transition (or the opposite - gmail to Exchange) Can you add to the points I have already outlined?

  Read the article

• VMWare Network bug in multiple VMWare Workstation versions if using a hardcoded IP address

  - by onyxruby

  I'm having a very tricky problem with some of my VM sessions being unable to reach the Internet or even ping the gateway. I have just set up a new VM Workstation (7) on a W2K8 64bit server (I'll be converting to ESXI 4 once I can find a decent book on it, so for the meanwhile I use workstation). I have imported a number of VM's and setup some new ones on the server.In short the problem with some of the VM's being unable to reach the Internet is that they can't reach the gateway. I've looking at a number of things and can pretty safely rule out the following: Switch, Router, DHCP Server, DNS, Client IP configuration, Routes and typos. The problem is that some of the new clients cannot reach the gateway if their IP address is hardcoded, they can't even ping it by IP address. That rules out DNS and DHCP. Now, if I allow them to get their IP address by DHCP they can reach the gateway and Internet without issue. The interesting thing on this, is that this behavior occurs even if I leave the DNS information hardcoded under TCP/IP settings. It doesn't work unless the IP and gateway are handed out by DHCP even though the same information IP info is being used by the host. Fundamentally from the standpoint of the clients, they are trying to reach the exact same gateway using the exact same IP information regardless of whether they are hardcoded or assigned by DHCP. Here's an example of one client. IP Address 192.168.7.66 - Subnet Mask 255.255.255.0 - Gateway 192.168.7.254 - DNS1 192.168.7.44 - DNS2 192.168.7.254. The issue occurs across six different microsoft operating systems, Windows 7 and Windows 2008 variants all have the issue. My W2K3, XP, Vista and W98 clients all work without issue with hardcoded IP addresses. I have tried things like rearranging the DNS order, flushing DNS and so on. It's not a routing or switch issue as the clients can work just fine if they get their IP by DHCP. It's not a paramater issue as the exact same paramaters are handed out by DHCP as I plug in by hand. It's not a DNS issue as clients cant reach other clients even with IP addresses only. I have run a tracert to the gateway by IP address and it times out on the very first hop before failing on hop3 with destination host unreachable. If I get the IP address by DHCP the tracert finds the gateway (and Internet) without issue. I have read a few other posts online in forums talking about this problem randomly occuring over the years in other VM versions as well, so I suspect some kind of long standing bug. Does anyone have any ideas on this? Is it possibly a bug with Windows 7 and W2K clients under VM?

  Read the article

• Disk performance below expectations

  - by paulH

  this is a follow-up to a previous question that I asked (Two servers with inconsistent disk speed). I have a PowerEdge R510 server with a PERC H700 integrated RAID controller (call this Server B) that was built using eight disks with 3Gb/s bandwidth that I was comparing with an almost identical server (call this Server A) that was built using four disks with 6Gb/s bandwidth. Server A had much better I/O rates than Server B. Once I discovered the difference with the disks, I had Server A rebuilt with faster 6Gbps disks. Unfortunately this resulted in no increase in the performance of the disks. Expecting that there must be some other configuration difference between the servers, we took the 6Gbps disks out of Server A and put them in Server B. This also resulted in no increase in the performance of the disks. We now have two identical servers built, with the exception that one is built with six 6Gbps disks and the other with eight 3Gbps disks, and the I/O rates of the disks is pretty much identical. This suggests that there is some bottleneck other than the disks, but I cannot understand how Server B originally had better I/O that has subsequently been 'lost'. Comparative I/O information below, as measured by SQLIO. The same parameters were used for each test. It's not the actual numbers that are significant but rather the variations between systems. In each case D: is a 2 disk RAID 1 volume, and E: is a 4 disk RAID 10 volume (apart from the original Server A, where E: was a 2 disk RAID 0 volume). Server A (original setup with 6Gpbs disks) D: Read (MB/s) 63 MB/s D: Write (MB/s) 170 MB/s E: Read (MB/s) 68 MB/s E: Write (MB/s) 320 MB/s Server B (original setup with 3Gpbs disks) D: Read (MB/s) 52 MB/s D: Write (MB/s) 88 MB/s E: Read (MB/s) 112 MB/s E: Write (MB/s) 130 MB/s Server A (new setup with 3Gpbs disks) D: Read (MB/s) 55 MB/s D: Write (MB/s) 85 MB/s E: Read (MB/s) 67 MB/s E: Write (MB/s) 180 MB/s Server B (new setup with 6Gpbs disks) D: Read (MB/s) 61 MB/s D: Write (MB/s) 95 MB/s E: Read (MB/s) 69 MB/s E: Write (MB/s) 180 MB/s Can anybody suggest any ideas what is going on here? The drives in use are as follows: Dell Seagate F617N ST3300657SS 300GB 15K RPM SAS Dell Hitachi HUS156030VLS600 300GB 3.5 inch 15000rpm 6GB SAS Hitachi Hus153030vls300 300GB Server SAS Dell ST3146855SS Seagate 3.5 inch 146GB 15K SAS

  Read the article

• Windows Question: RunOnce/Second Boot Issues

  - by Greg

  I am attempting to create a Windows XP SP3 image that will run my application on Second Boot. Here is the intended workflow. 1) Run Image Prep Utility (I wrote) on windows to add my runonce entries and clean a few things up. 2) Reboot to ghost, make image file. 3) Package into my ISO and distribute. 4) System will be imaged by user. 5) On first boot, I have about 5 things that run, one of which includes a driver updater (I wrote) for my own specific devices. 6) One of the entries inside of HKCU/../runonce is a reg file, which adds another key to HKLM/../runonce. This is how second boot is acquired. 7) As a result of the driver updater, user is prompted to reboot. 8) My application is then launched from HKLM/../runonce on second boot. This workflow works perfectly, except for a select few legacy systems that contain devices that cause the add hardware wizard to pop up. When the add hardware wizard pops up is when I begin to see problems. It's important to note, that if I manually inspect the registry after the add hardware wizard pops up, it appears as I would expect, with all the first boot scripts having run, and it's sitting in a state I would correctly expect it to be in for a second boot scenario. The problem comes when I click next on the add hardware wizard, it seems to re-run the single entry I've added, and re-executes the runonce scripts. (only one script now as it's already executed and cleared out the initial entries). This causes my application to open as if it were a second boot, only when next is clicked on the add hardware wizard. If I click cancel, and reboot, then it also works as expected. I don't care as much about other solutions, because I could design a system that doesn't fully rely on Microsoft's registry. I simply can't find any information as to WHY this is happening. I believe this is some type of Microsoft issue that's presenting itself as a result of an overstretched image that's expected to support too many legacy platforms, but any help that can be provided would be appreciated. Thanks,

  Read the article

• Install Ubuntu 12.04 in UEFI mode on a HP Pavilion dv6-6c40ca

  - by Marlen T. B.

  I have recently (as of July 2012) bought a HP Pavilion dv6-6c40ca laptop. It came pre-installed with Windows 7 on an MBR. I installed Ubuntu 12.04 on it on a GPT partition in what I think is BIOS emulation mode. I made a BIOS-Grub partition so the install didn't fail. That is what it is for .. right? Now I want to upgrade to UEFI mode. How would I Install Ubuntu 12.04 in UEFI mode on a HP Pavilion dv6-6c40ca. Or is it impossible? My laptop, despite its new age may not be UEFI 2.0+ capable. If it isn't how can I install a software UEFI (i.e. a DUET such as the one by tianocore). Or is this too impossible? A link to my laptop's specs is: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03137924&tmp_task=prodinfoCategory&cc=ca&dlc=en&lang=en&lc=en&product=5218530 My laptop should have a UEFI given this link from HP http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c01442956#N218. And from the link I draw a quote: That means most notebooks distributed with Windows Vista, and all notebooks distributed with Windows 7, have the UEFI environment. My laptop had Windows 7 Home Premium pre-installed. OK. Following the comments so far -- NOTE: I am trying to do this on an external drive so I can see if it works. I have partitioned the drive using GParted as a GPT drive. Created a 200MB partition at the beginning of the drive with a FAT32 file system. Given the 200MB partition a label of "EFI". Set the boot flag on the 200MB partition. What should a do next to install Ubuntu 12.04? Given the link: https://help.ubuntu.com/community/UEFIBooting#Selecting_the_.28U.29EFI_Graphic_Protocol In my first read through (just to see if I will understand everything before I start) I get to step 2.3 Install GRUB2 in (U)EFI systems The first line is Boot into Linux (any live ISO) preferably in UEFI mode. Um .. how do you tell what mode your live CD is in?! And how do you change it if the mode is wrong?

  Read the article

• TPROXY Not working with HAProxy, Ubuntu 14.04

  - by Nyxynyx

  I'm trying to use HAProxy as a fully transparent proxy using TPROXY in Ubuntu 14.04. HAProxy will be setup on the first server with eth1 111.111.250.250 and eth0 10.111.128.134. The single balanced server has eth1 and eth0 as well. eth1 is the public facing network interface while eth0 is for the private network which both servers are in. Problem: I'm able to connect to the balanced server's port 1234 directly (via eth1) but am not able to reach the balanced server via Haproxy port 1234 (which redirects to 1234 via eth0). Am I missing out something in this configuration? On the HAProxy server The current kernel is: Linux extremehash-lb2 3.13.0-24-generic #46-Ubuntu SMP Thu Apr 10 19:11:08 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux The kernel appears to have TPROXY support: # grep TPROXY /boot/config-3.13.0-24-generic CONFIG_NETFILTER_XT_TARGET_TPROXY=m HAProxy was compiled with TPROXY support: haproxy -vv HA-Proxy version 1.5.3 2014/07/25 Copyright 2000-2014 Willy Tarreau <[email protected]> Build options : TARGET = linux26 CPU = x86_64 CC = gcc CFLAGS = -g -fno-strict-aliasing OPTIONS = USE_LINUX_TPROXY=1 USE_LIBCRYPT=1 USE_STATIC_PCRE=1 Default settings : maxconn = 2000, bufsize = 16384, maxrewrite = 8192, maxpollevents = 200 Encrypted password support via crypt(3): yes Built without zlib support (USE_ZLIB not set) Compression algorithms supported : identity Built without OpenSSL support (USE_OPENSSL not set) Built with PCRE version : 8.31 2012-07-06 PCRE library supports JIT : no (USE_PCRE_JIT not set) Built with transparent proxy support using: IP_TRANSPARENT IPV6_TRANSPARENT IP_FREEBIND Available polling systems : epoll : pref=300, test result OK poll : pref=200, test result OK select : pref=150, test result OK Total: 3 (3 usable), will use epoll. In /etc/haproxy/haproxy.cfg, I've configured a port to have the following options: listen test1235 :1234 mode tcp option tcplog balance leastconn source 0.0.0.0 usesrc clientip server balanced1 10.111.163.76:1234 check inter 5s rise 2 fall 4 weight 4 On the balanced server In /etc/networking/interfaces I've set the gateway for eth0 to be the HAProxy box 10.111.128.134 and restarted networking. auto eth0 eth1 iface eth0 inet static address 111.111.250.250 netmask 255.255.224.0 gateway 111.131.224.1 dns-nameservers 8.8.4.4 8.8.8.8 209.244.0.3 iface eth1 inet static address 10.111.163.76 netmask 255.255.0.0 gateway 10.111.128.134 ip route gives: default via 111.111.224.1 dev eth0 10.111.0.0/16 dev eth1 proto kernel scope link src 10.111.163.76 111.111.224.0/19 dev eth0 proto kernel scope link src 111.111.250.250

  Read the article

• Output php mail calls to log file

  - by Tom McQuarrie

  This question relates to the question found here: Find the php script thats sending mails Trying to do the exact same thing but can't get the log to output what I need. Not too experienced with serverfault and ideally I'd post my followup on the original question, or PM adam to see if he ever found a solution, but looks as though server fault doesn't work that way. I can post an "answer" but that's definitely not what this is. I have a script located at /usr/local/bin/sendmail-php-logged, with the following: #!/bin/sh logger -p mail.info sendmail-php: site=${HTTP_HOST}, client=${REMOTE_ADDR}, script=${SCRIPT_NAME}, filename=${SCRIPT_FILENAME}, docroot=${DOCUMENT_ROOT}, pwd=${PWD}, uid=${UID}, user=$(whoami) /usr/sbin/sendmail -t -i $* This is logging to /var/log/maillog, but as Adam mentions in his question, none of the server variables work. Output I'm getting is: Oct 4 12:16:21 fluke logger: sendmail-php: site=, client=, script=, filename=, docroot=, pwd=/var/www/html/aro_chroot/sites/arocms, uid=48, user=apache Oct 4 12:16:21 fluke logger: sendmail-php: site=, client=, script=, filename=, docroot=, pwd=/var/www/html/aro_chroot/sites/arocms, uid=48, user=apache Oct 4 12:17:03 fluke logger: sendmail-php: site=, client=, script=, filename=, docroot=, pwd=/var/www/html/aro_chroot/sites/arocms, uid=48, user=apache Oct 4 12:17:05 fluke logger: sendmail-php: site=, client=, script=, filename=, docroot=, pwd=/root, uid=0, user=root Oct 4 12:17:11 fluke logger: sendmail-php: site=, client=, script=, filename=, docroot=, pwd=/var/www/html/aro_chroot/sites/arocms, uid=48, user=apache Oct 4 12:17:14 fluke logger: sendmail-php: site=, client=, script=, filename=, docroot=, pwd=/root, uid=0, user=root Oct 4 12:17:29 fluke logger: sendmail-php: site=, client=, script=, filename=, docroot=, pwd=/root, uid=0, user=root Oct 4 12:17:41 fluke logger: sendmail-php: site=, client=, script=, filename=, docroot=, pwd=/root, uid=0, user=root User ID, current user, and pwd are all working, probably because they're globally accessible script resources, and not specific to PHP, like all the others are. I've tried using other server variables as per labradort's instructions, but no joy. Here's some sample tests: logger -p mail.info sendmail-php SCRIPT_NAME: ${SCRIPT_NAME} logger -p mail.info sendmail-php SCRIPT_FILENAME: ${SCRIPT_FILENAME} logger -p mail.info sendmail-php PATH_INFO: ${PATH_INFO} logger -p mail.info sendmail-php PHP_SELF: ${PHP_SELF} logger -p mail.info sendmail-php DOCUMENT_ROOT: ${DOCUMENT_ROOT} logger -p mail.info sendmail-php REMOTE_ADDR: ${REMOTE_ADDR} logger -p mail.info sendmail-php SCRIPT_NAME: $SCRIPT_NAME logger -p mail.info sendmail-php SCRIPT_FILENAME: $SCRIPT_FILENAME logger -p mail.info sendmail-php PATH_INFO: $PATH_INFO logger -p mail.info sendmail-php PHP_SELF: $PHP_SELF logger -p mail.info sendmail-php DOCUMENT_ROOT: $DOCUMENT_ROOT logger -p mail.info sendmail-php REMOTE_ADDR: $REMOTE_ADDR And the output: Oct 4 12:58:02 fluke logger: sendmail-php SCRIPT_NAME: Oct 4 12:58:02 fluke logger: sendmail-php SCRIPT_FILENAME: Oct 4 12:58:02 fluke logger: sendmail-php PATH_INFO: Oct 4 12:58:02 fluke logger: sendmail-php PHP_SELF: Oct 4 12:58:02 fluke logger: sendmail-php DOCUMENT_ROOT: Oct 4 12:58:02 fluke logger: sendmail-php REMOTE_ADDR: Oct 4 12:58:02 fluke logger: sendmail-php SCRIPT_NAME: Oct 4 12:58:02 fluke logger: sendmail-php SCRIPT_FILENAME: Oct 4 12:58:02 fluke logger: sendmail-php PATH_INFO: Oct 4 12:58:02 fluke logger: sendmail-php PHP_SELF: Oct 4 12:58:02 fluke logger: sendmail-php DOCUMENT_ROOT: Oct 4 12:58:02 fluke logger: sendmail-php REMOTE_ADDR: I'm running php 5.3.10. Unfortunately register_globals is on, for compatibility with legacy systems, but you wouldn't think that would cause the environment variables to stop working. If someone can give me some hints as to why this might not be working I'll be a very happy man :)

  Read the article

• What is a good method to solve cabal install problems?

  - by sp3ctum

  I've used the cabal package manager for Haskell programs to install libraries and new projects that I've cloned from some repositories. More often than not, I keep running into problems. Most projects make installing them seem super easy, but in my case that's not always true - sometimes they are very hard to get running. Some are so hard, in fact, that I've lost interest in the project solely because of not being able to install it. So instead of complaining, I'd like to ask what I should do to better this situation. I'd like to use my most recent problem as an example. I'm interested in trying out the Gitit project. It's a promising looking personal wiki that runs on various version control systems. So here's what I've done: Clone from Github run cabal install in the project directory like I'm told on the project install page: mika@eka:~/git/gitit$ ls BLUETRIP-LICENSE CHANGES HCAR-gitit.tex LICENSE Network README.markdown RELANN-0.6.1 Setup.lhs TANGOICONS YUI-LICENSE data expireGititCache.hs gitit.cabal gitit.hs plugins mika@eka:~/git/gitit$ cabal install Resolving dependencies... cabal: cannot configure happstack-server-7.0.7. It requires base64-bytestring ==1.0.* For the dependency on base64-bytestring ==1.0.* there are these packages: base64-bytestring-1.0.0.0. However none of them are available. base64-bytestring-1.0.0.0 was excluded because gitit-0.10 requires base64-bytestring ==0.1.* mika@eka:~/git/gitit$ So now I'm thinking: well, I'll install happstack-server on its own, maybe that will work: mika@eka:~/git/gitit$ cabal install happstack-server Resolving dependencies... Warning: happstack-server.cabal: Ignoring unknown section type: test-suite Configuring happstack-server-7.0.7... cabal: At least the following dependencies are missing: blaze-html ==0.5.*, hslogger >=1.0.2, monad-control ==0.3.*, network >=2.2.3, sendfile >=0.7.1 && <0.8, system-filepath >=0.3.1, text >=0.10 && <0.12, threads >=0.5, transformers-base ==0.4.* cabal: Error: some packages failed to install: happstack-server-7.0.7 failed during the configure step. The exception was: ExitFailure 1 So looks like there are some dependencies missing. But isn't installing these dependencies the whole point of using cabal in the first place? What should I do? File bug reports (to which project?), install the dependencies manually or something else? Bonus points for explaining what causes these kinds of problems.

  Read the article

• Splitting an internet connection between multiple separate subnetworks

  - by pythonian4000

  Problem I have an internet connection that I want to split between four separate networks. My requirements are: I need to be able to monitor the amount of bandwidth and data being used by each network, and notify or control as necessary. The four networks should only be able to connect to the internet, not each other. My parents need to be able to operate it, so it needs a simple, preferably Windows-based GUI. Progress so far Server I have a mini-ITX server with six Gigabit ethernet ports - one for the ethernet internet connection, one for each of the four networks, and one for remote access to the server for administration. Bandwidth control I spent a long time researching solutions here. The majority of the control systems/software I found could control bandwidth usage via QOS, but could not monitor or control the amount of data being used. Eventually I found the SoftPerfect Bandwidth Manager, which has everything I need in terms of monitoring and control - per-interface quota management, usage statistics, a web interface for checking usage, and email notifications when quotas are exceeded. It is also Windows-based and has a simple GUI. Internet sharing This is where I am having issues. I am currently using Windows XP Pro SP2 for the server (yes, I know this is far from ideal, but it's the only spare Windows OS I currently have). I can't use the built-in Internet Connection Sharing for several reasons: The upstream internet router has an IP of 192.168.0.1 which ICS clashes with, and I cannot change the router settings. ICS can only share an internet connection with a single interface, but I have four. I have tried bridging the four network cards, but then the Bandwidth Manager cannot see the four individual interfaces - it only sees the bridge. I have tried setting up Dual DHCP DNS server (and am having issues getting DHCP offers to be received by clients), but that would still require gateway software of some sort, which I have been unable to find. My current attempt is to use OpenVPN, with a server for the internet NIC and a separate client for each of the four networks. My thought is that I could bridge the OpenVPN TAP devices to each NIC, meaning that the Bandwidth Manager would control traffic from the bridge instead of the interface. I have not made much progress here though - I've never used OpenVPN before. Questions Is there a Windows software package that does everything I need? (Unlikely, I know) Is there a Windows software package that will share internet between multiple NICs without bridging? Are either of my about attempts feasible? Would it help to have a newer/server version of Windows? Is there a non-Windows alternative that is easy to use?

  Read the article

• SQL Server High Availability - Mirroring with MSCS?

  - by David

  I'm looking at options for high-availability for my SQL Server-powered application. The requirements are: HA protection from storage failure. Data accessibility when one of the DB servers is undergoing software updates (e.g. planned outage for Windows Update / SQL Server service-packs). Must not involve much in the way of hardware procurement. The application is an ASP.NET web application. The web application's users have their own database instances. I've seen two main options: SQL Server failover clustering, and SQL Server mirroring. I understand that SQL Server Failover Clustering requires the purchasing of a shared disk array and doesn't offer any protection if the shared storage goes down (so the documentation recommends to set up a Mirroring between two clusters). Database Mirroring seems the cheaper option (as it only requires two database servers and a simple witness box) - but I've heard it doesn't work well when you have a large number of databases. The application I'm developing involves giving each client their own database for their application - there could be hundreds of databases. Setting up the mirroring is no problem thanks to the automation systems we have in place. My final point concerns how failover works with respect to client connections - SQL Server Failover Clustering uses MSCS which means that the cluster is invisible to clients - a connection attempt might fail during the failover, but a simple reconnect will have it working again. However mirroring, as far as I know, requires that the client be aware of the mirrored partners: if the client cannot connect to the primary server then it tries the secondary server. I'm wondering how this work with respect to Connection Pooling in ASP.NET applications - does the client connection failovering mean that there's a potential 2-second (assuming 2000ms TCP timeout policy) pause when the connection pool tries the primary server on every connection attempt? I read somewhere that Mirroring can be used on top of MSCS which means that the client does not need to be aware of mirroring (so there wouldn't be any potential delays during connection, and also that no changes would need to be made to the client, not even the connection string) - however I'm finding it hard to get documentation or white papers on this approach. But if true, then it means the best method is then Mirroring (for HA) with MSCS (for client ignorance and connection performance). ...but how does this scale to a server instance that might contain hundreds of mirrored databases?

  Read the article

• "Error loading operating system": Win7/Vista

  - by LookitsPuck

  Have this computer for about 2 years now. Originally had Vista installed, now have Windows 7 installed. Both on separate hard drives. Also have another drive used strictly for media. About a week ago, the Vista hard drive started going on its way out. Was getting problems on startup. After a few BIOS settings, I was able to get into Windows 7 and everything was fine. However, I started remembering the startup issues, so I deleted the bootup for Vista under msconfig. Didn't restart the computer at that time, though. For a few days, everything was ok. Last night I play a little poker, then hit the hay. I wake up to a good ole "Error loading operating system" on the screen. Just wonderful. Looks like the computer restarted overnight (auto updates, anyone?). So, after a big of finagling and half hearted tries, I can't get past the "Error loading operating system" screen. FWIW, in the BIOS it can see my hard drives fine. So I move on. I get my Windows 7 installation disk to try and do a repair. Go in the BIOS, change boot priority to DVD drive, and we're on our merry way. After loading from the disc, I first try jumping into the "Repair your computer" section. That opens up the System Recovery Options. However, this is where the problem comes into play. I don't see any operating systems here. Nada. What's odd though is if I click on the Load Drivers button, I can see my Windows 7 partition (C:), and can go through the files and folders without issue. What do I do at this point? I can't repair it. It seems like I can traverse the hard drive without issue when in an open dialog in the System Recovery Options, but I'm getting the good ole "Error loading computer" on bootup. Suggestions? Thanks all!!

  Read the article

• !! 0xc01a00d !! aka Vista won't boot

  - by Chris

  Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box. One of my users has an HP DV5-1235dx laptop running Windows Vista Professional x64. Last night, our WSUS server pushed out a few updates including "Security Update for Windows Vista for x64-based Systems (KB960859)". When we try to boot the laptop today, a black screen with white text comes up displaying: xxx/169894 (something) Where xxx increments rapidly and something is some dll or registry key. Eventually that stops and the screen displays !! 0xc01a00d !! 35566/169894 (\Registry\Machine\COMPONENTS\DerivedDat...) No other computers that received this update are displaying the same error. So far I've tried running CHKDSK off of HBCD. It repaired a thing or two, but the computer still doesn't boot. I tried repairing the Windows install from the Vista CD, but I get a black screen with white text displaying something along the lines of: 0 No Emulation System Type 00 1 No Emulation System Type 00 Select one of the above Booting in Last Known Good Configuration doesn't work. Booting in Safe Mode freezes at Loading Windows Files [snip] Loaded: \windows\system32\drivers\crcdisk.sys Please wait... My next step is trying to boot Safe Mode with Command Prompt and try to run rstrui.exe. While I do that, does anybody have any guidance? Edit: Booting into Safe Mode with Command Prompt will not work. See Booting in Safe Mode above. Edit 2: I managed to boot from the Vista DVD. I ran the system repair, and now I get a black screen with white text saying: !! 0xc0000034 !! 290/169894 (_0000000000000000.cdf-ms) Edit 3: I ran the system repair again, and it attempted to repair my hard drive. It failed. Problem Signature: Problem Event Name: Startup Repair V2 Problem Signature 01: External Media Problem Signature 02: 6.0.6001.18000.6.0.6001.18000 Problem Signature 03: 4 Problem Signature 04: 196611 Problem Signature 05: CorruptVolume Problem Signature 06: NoBootFailure Problem Signature 07: 0 Problem Signature 08: 0 Problem Signature 09: unknown Problem Signature 10: 1168 OS Version: 6.0.6002.2.2.0.256.1 Locale ID: 1033 Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box.

  Read the article

• where on disk is space allocated for new files inside LVM lv with ext4 file system?

  - by Jost

  I run a multi-disk server with LVM2. Several large disks serve as LVM2 physical volumes for one volume group, containing one logical volume formatted with ext4. Nothing fancy, just your standard linear setup. Recently an additional, very small disk was added as physical volume to that volume group and I expanded both the logical volume, and the ext4 file system therein onto that disk. This lv is used to store incremental backups using rsync and is only about 30% full, there have rarely been any files deleted from it, only incremental writes. Now this new HDD I added to the pre-existing volume group has unexpectedly died on me, and the volume group won't come up because it is missing one physical volume. As fate will have it, this WAS the "in an event of catastrophic failure on the primary server"-backup, the event happened, the boss is not happy, so this kinda has to work... According to this (Part 3): http://www.novell.com/coolsolutions/appnote/19386.html it is possible to trick LVM into starting anyway by creating a new pv with identical metadata to the failed disk, which will make the volume accessible, but of course leave giant holes in the file system. I have'n tried it yet, because it involves repairing (writing to) the file system which eliminates the possibility of trying other things if it fails. Now my question is: How does this setup actually allocate disk space for new data? Is it allocated linearly from beginning to end of PVs, in the order they were added to the vg? Is it striped somehow in order to increase performance/balance load? since this defective disk was added only later to an existing lvm2 vg and lv, containing a half-empty ext4, what are the chances that there was never any data written to the defective disk? In other words: what are the chances of recovering all my data, even without the defective disk, by just starting the volume group as-is? Am I about to go spend $1500 on having 250GB of empty space recovered when I send the defective disk in for repair? Is there a way to check without mounting the file system and opening the files, hoping they contain something other than zeros? (comparing addresses of used data blocks inside ext4 to address ranges that were on the missing pv, something like that, preferably easy to automate) I know bitwise-copying the entire lv into an image file before trying to repair the ext4 would probably be a good idea, but since this lv is very large and I just suffered major file system failure on several systems it is probably a luxury I don't have... Any suggestions?

  Read the article

• What are some of the best wireless routers for a price-conscious home power-user?

  - by Alain

  I'm extremely dissatisfied with the 'popular' choice for routers in homes and small offices. They are expensive (upwards of 60$), lack a great deal of useful configuration options, and seem to need to be restarted quite often. (Linksys comes to mind). I've been on the market for a good router lately, and slowly collecting a set of requirements I feel good routers should meet. Maximum number of TCP/IP connections. - This isn't something I see any routers advertise, but in terms of supporting torrent applications, I've been screwed by routers that support less than 20 here. From what I understand a fairly standard number is 200, but there are not so expensive routers that support thousands. Router configuration menu - Most have standard menu's that let you set up basic things like your wireless network encryption settings, uPnP, and maybe even DMZ (demilitarized zones). An absolute requirement for me, however, are routers with good enough firmware to support: Explicit Port forwarding Assigning static local ips to specific mac addresses, or at least Port forwarding by MAC address Port, IP and MAC filtering Dynamic DNS service for home users who want to set up a server but have a dynamic IP Traffic shaping (ideally) - giving priority to packets from certain machines or over certain ports. Strong wireless signal - If getting a reliable signal requires me to be so close to the router that I can connect an Ethernet cable, it's not good enough. As many Ethernet ports as possible. - Because I want to be able to switch from console gaming to PC gaming without visiting my router. So far, the best thing I've stumbled upon (in the bargain bin at staples) was a 20$ retail plus router. It was meant to be the cheapest alternative until I could find something better to purchase online, but I was actually blown away by the firmware capabilities. It supports defining reserved bandwidth for certain network traffic, dynamic DNS, reserving local IPs for specific MAC addresses, etc. At 2 am when my roommate is killing our Internet with their torrents, I can limit their bandwidth without outright blacklisting them. I have, however, met serious limitations when it comes to network traffic between local machines. It claims a 300Mbps connection, but I have trouble streaming videos from my PC to my console or other laptops wirelessly. It has a meltdown and needs to be reset once in a while (no more than a couple times a month), and it's got a 200 connection limit. There 4 Ethernet ports in the back but I'm pretty sure the first doesn't work. So some great answers to this question would be: Any metrics you use to compare routers, and requirements you have for new candidates. The best routers you've found for supporting home servers, file management systems, high volume torrent traffic, good price/feature ratio, etc. Good configuration advice (aside from 'use Ethernet whenever possible') Thanks for your feedback and experiences!

  Read the article

• Ubuntu Newbie Needs Assistance!!

  - by Steve Greene

  New Ubuntu User Needs Help!- version 9.10 does not communicate with laptop Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, even when sitting directly under the wireless router at the local library (literally), which puts out a wickedly-fast signal that my Windows Vista OS auto-detects and immediately connects to. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all, even though I am only a few feet from the router. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I desparately wish to convert to Ubuntu. I used Mac for ten years, and then Windows for ten years. Now, after 20 years, I want to live out my days as an open-source Ubuntu fanatic. I am ready to give the old status quo the boot! I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch so that I can move on in total Ubuntu bliss? My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System. I am running Windows Vista Home Basic, Service Pack 2. My current email is [email protected] if you have a workable solution that does not require programmer status to implement. Surely this must be a simple fix that I simply am overlooking, but being the new guy on the block, I have yet to be enlightened. Thanks for your help in coming up to speed!! Steve Wanna' be Ubuntu Fanatic "If you're not living on the edge, you're taking up too much space."

  Read the article

• RHEL5: Can't create sparse file bigger than 256GB in tmpfs

  - by John Kugelman

  /var/log/lastlog gets written to when you log in. The size of this file is based off of the largest UID in the system. The larger the maximum UID, the larger this file is. Thankfully it's a sparse file so the size on disk is much smaller than the size ls reports (ls -s reports the size on disk). On our system we're authenticating against an Active Directory server, and the UIDs users are assigned end up being really, really large. Like, say, UID 900,000,000 for the first AD user, 900,000,001 for the second, etc. That's strange but should be okay. It results in /var/log/lastlog being huuuuuge, though--once an AD user logs in lastlog shows up as 280GB. Its real size is still small, thankfully. This works fine when /var/log/lastlog is stored on the hard drive on an ext3 filesystem. It breaks, however, if lastlog is stored in a tmpfs filesystem. Then it appears that the max file size for any file on the tmpfs is 256GB, so the sessreg program errors out trying to write to lastlog. Where is this 256GB limit coming from, and how can I increase it? As a simple test for creating large sparse files I've been doing: dd if=/dev/zero of=sparse-file bs=1 count=1 seek=300GB I've tried Googling for "tmpfs max file size", "256GB filesystem limit", "linux max file size", things like that. I haven't been able to find much. The only mention of 256GB I can find is that ext3 filesystems with 2KB blocks are limited to 256GB files. But our hard drives are formatted with 4K blocks so that doesn't seem to be it--not to mention this is happening in a tmpfs mounted ON TOP of the hard drive so the ext3 partition shouldn't be a factor. This is all happening on a 64-bit Red Hat Enterprise Linux 5.4 system. Interestingly, on my personal development machine, which is a 32-bit Fedora Core 6 box, I can create 300GB+ files in tmpfs filesystems no problem. On the RHEL5.4 systems it is no go.

  Read the article

• Looking for a fiber optic "switch" or "router" for home use

  - by Shrout1

  The gist of my question: What is a "fiber optic" switch called? I.E. a layer 2 ethernet switch that uses fiber TX and RX connections and sends layer 2 network traffic between the fiber strands that are connected. Can someone purchase a dedicated fiber switch that does not have copper ethernet ports? What is the current average price of a device like this? Not necessarily looking for product endorsements, just information Might not make sense to go this route if it is too cost prohibitive What type of fiber connector is used for terminating a fiber strand into a jack on the wall? Can fiber be "patched" using two jacks and a "patch" cable? Is signal loss a concern with the longest runs at 100-200ft, a patch cable and media converters? The full story: My parents had unterminated fiber optic cable and terminated Cat5e run throughout their home when it was built in 2004. 10 years later the Cat5e isn't providing the throughput that my father needs to accomplish multiple streams of HD and fast system backups throughout the house. He can't reach gigabit speeds across the distance of the Cat5e runs. We are both interested in terminating the fiber connections and using them as high speed "backbones" to copper switches in each room of the house. It would be easy to attain gigabit speeds (or better, eventually) using the fiber. I have searched and searched for a "fiber optic switch" or "fiber optic router" and cannot find the correct term to describe this piece of hardware. We can use fiber media converters at the end points of each connection, however it would be nice to have a "patch panel" set up in the network closet in the basement that has fiber connections on it and switches the ethernet streams between the connections/systems in the house. Each fiber media converter costs between $50-$100 a piece... After 10 or so terminated connections it might make sense to find a piece of hardware that does not require media converters. That would depend upon the cost of this hardware Somewhat unrelated, if we are able to route between these fiber strands successfully, what is the physical connector type used in a jack on the wall? Just like RJ45 has a wall outlet (depicted below): What is the fiber optic equivalent of this? In the interim could we "patch" a couple fiber strands together in the network closet? Would signal loss be of concern with a run length of 100-200 feet, a patch cable and two media converters? If that would work then it could be used until the funds are available for more.

  Read the article

• File/printer sharing issues on network with multiple OSes

  - by DanZ

  My workplace consists of computers running a variety of different operating systems, and I have been running into problems getting some of them to connect to a shared drive and printer over the network. Here is a brief description of the computers involved and the issues I have encountered: 1: Dell desktop, Windows Vista Business-- This is the computer I want the others to connect to. It has a USB printer and eSATA hard drive enclosure that I have set up for sharing, with different accounts for the various users. 2: Fujitsu laptop, Windows XP Tablet edition-- No problems. Can connect to both the shared printer and hard drive. 3: Lenovo laptop, Windows Vista Business 64 bit-- No problems. Can connect to both the shared printer and drive. 4: Apple MacBook, OS 10.4-- Can connect to the shared drive, but not to the shared printer. I am aware that the printer issue is due to a known incompatibility between Vista and OS 10.4 and earlier with regards to Samba. It is not a big problem, however, as this computer can access a network printer. 5: Sony laptop, Windows Vista Home Premium-- Can connect to the shared printer, but not the shared drive. It can see computer 1 and its shared drive on the network, and appears to successfully log in to user accounts. However, if you try to access the shared drive, it says you do not have permission. I have tried both standard and administrator accounts, and none can access the drive from this computer. 6: MacBook Pro, OS 10.5 (there are two of these)-- Can connect to the shared printer, but not the shared drive. They can't see computer 1 on the network. For that matter, they also can't see each other or the older Mac, but can see and access shared folders on the XP machine (computer 2) and can see other PCs in the building. I was able to add the shared printer manually by typing in its network location, but was unable to manually add the shared drive in the same way. So, what I am looking for is suggestions on how to get computers 5 and 6 to connect to the shared drive. Since they can already connect to the shared printer (which is on the same computer as the shared drive), it seems reasonable that they should be able to access the drive as well.

  Read the article

• How can Windows XP/7 users cleanly connect to Mac OS X Server 10.9.4 Mavericks with Active Directory integration?

  - by JakeGould

  I’m a Linux/Unix systems admin who also manages a Macintosh server infrastructure & there is a lone Mac Mini in the mix running 10.9.4 that I would like Windows XP & Windows 7 users to connect to with little or no hassle. The problem? Windows users can’t seem to even get to the point of a password prompt yet connect. Mind you this server replaced a Mac OS X 10.6.8 server that had issues, but never had issues with Windows users connected. The gist of this post is: The tons of different messages out there about Mac OS X 10.9.4 Samba support are mind-numbingly confusing. Can anyone share some solid specifics here? I’ve read pieces like this one here that suggest turning off file sharing & then adding a share with AFP/SMB enabled would work. But the suggestion seems to apply to 10.8. And from what I know a lot has changed in Samba support in 10.9 let alone the iterations to 10.9.4. Then I found this great tutorial here that explains things step-by-step. Which seems like it should work, but the problem is the example given applies to a local user created on the Mac when I would like users in an Active Directory group—which the Mac is bound to—access the Mac Mini shares. There are also tons of great tips here on MacWindows.com but nothing seems solid to the issue I am facing. So from what I am reading these are my options: Local User Versus Active Directory: Setup a common local user on the Mac OS X 10.9.4 server to be used for Samba sharing since Active Directory won’t work. Is this really the case? Because loss of AD integration is a major pain. Do Extended File Attributes Get Retained from Windows Users: If this were to work, how do extended attributes come into play? Loss of metadata & related info is not an option. How Fragile is Any of this to Updates: How does any of this shake out with Mac OS X updates as well as Windows updates? Installing Official, Open Source Samba: Would upgrading the Samba install on the server to the official open source Samba via a package like SMBUp or via the Hombrew method described here help or make the issue worse? I fully understand there have historically been issues in mixed environments, but nowadays Windows users connecting to a Mac seem to have a truly hellish road ahead of them. Unless I am missing something?

  Read the article

• Windows 7 The boot selection failed because a required device is inaccessible 0xc000000f

  - by piratejackus

  I have a problem with my Windows 7, hardware : Acer 3820TG Operating Systems : Windows 7 and Ubuntu 10.04 dual Case: When I try to boot my windows 7 I see an error: "Window failed to start. A recent hardware or software change might be the cause. To fix the problem: 1.Insert.... 2. .... ... status : 0xc000000f info : The boot selection failed because a required device is inaccessible .... " I can't exactly remember what were my last actions on Windows. I already searched this error and applied the proposed solutions, I created a repair USB (because I don't have a CD-ROM nor a Windows 7 CD) such as; -repair operating system :it says it cannot repair it -checking disk (chkdsk D: /f /r) : it checks the disk without a problem or error and it takes pretty long (more than a hour). But when I restart, still the same error. -I didn't create a restore point so I pass this option -I don't have a system image -I tried to run windows recovery (I have a recovery partition) but there are just two options: 1- Format the operating system but retain user data (copies the files under users to c\backup folder, but when I searched deeper I found that there are some people who already tried this option and couldn't find their user files under backup directory). Plus, I have unfortunately just one partition D (it is a fault I know) because I use always Ubuntu. So this is not applicable in my situation 2- Format entire system (Windows). I keep my valuable data in windows but not in user folder. I was reaching them from Windows. -I tried to repair windows boot by: bootrec /fixMBR bootrec /fixBoot bootrec /rebuildBCD I lost all grub menu, and reinstalled it. - ubuntuforums.org/showthread.php?t=1014708&page=29 nothing changed, same error. I created a thread in microsoft forums - http://social.answers.microsoft.com/Forums/en-US/w7install/thread/69517faf-850a-45fd- 8195-6d4ed831f805 but I couldn't find a solution. Before I run chkdsk from usb repair disk I couldn't able to mount Windows (NTFS) partition from Ubuntu, I was getting "couldn't mount file system, error code 2". I tried to fix ntfs partition from ubuntu and got "segmentation fault". I also created a thread on ubuntuforums for this mount problem: - http://ubuntuforums.org/showthread.php?t=1606427 So, after chkdsk, I could enable to mount windows partition but all I see in this partition is chkdsk logs, no any other data. Now, I don't think I lost my data because I don't get any filesystem errors, just the boot section, but this log files under windows partition makes me afraid. I see that Microsoft developers don't have a solution yet for this error. If you need any information to get more idea I can give, maybe I miss some points or it could be complicated. Thanks in advance.

  Read the article

• Win XP error 0x80041003 using GetObject/winmgmts

  - by John Lewis

  My computer is called "neil" and I want to set some values using WMI in vbScript. I adapetd the script below from one supplied by Microsoft. When I run it in my browser I get Error Type: (0x80041003) /dressage/30/pdf2.asp, line 8 I suspect it is some registry/security setting. Any advice? John Lewis FULL SCRIPT call Print_HTML_Page("http://neil/dressage/ascii.asp", "ascii") Sub SetPDFFile(strPDFFile) Const HKEY_LOCAL_MACHINE = &H80000002 strKeyPath = "SOFTWARE\Dane Prairie Systems\Win2PDF" strComputer = "." Set objReg=GetObject( _ "winmgmts:{impersonationLevel=impersonate}!\\" & _ strComputer & "\root\default:StdRegProv") strValueName = "PDFFileName" objReg.SetExpandedStringValue HKEY_LOCAL_MACHINE,_ strKeyPath,strValueName,strPDFFile End Sub Sub Print_HTML_Page(strPathToPage, strPDFFile) SetPDFFile( strPDFFile ) Set objIE = CreateObject("InternetExplorer.Application") 'From http://www.tek-tips.com/viewthread.cfm?qid=1092473&page=5 On Error Resume Next strPrintStatus = objIE.QueryStatusWB(6) If Err.Number 0 Then MsgBox "Cannot find a printer. Operation aborted." objIE.Quit Set objIE = Nothing Exit Sub End If With objIE .visible=0 .left=200 .top=200 .height=400 .width=400 .menubar=0 .toolbar=1 .statusBar=0 .navigate strPathToPage End With 'Wait until IE has finished loading Do while objIE.busy WScript.Sleep 100 Loop On Error Goto 0 objIE.ExecWB 6,2 'Wait until IE has finished printing WScript.Sleep 2000 objIE.Quit Set objIE = Nothing End Sub Update: Thanks for your reply. The line breaks seem to have been introduced in the process of paasting into this form. Well spotted - I was using a PDF file name "ascii". I added a .pdf extension but still get the error. I suspect you're right that it's to do with admin rights. Here's more about the setup and what I'm trying to achieve. Win2pdf is a product for writing PDFs by works by simulating a Windows printer. You "print" the page, select win2pdf in the print dialog and it then asks for a file name. I have it installed on my pc (called Neil) and it works fine in this conventional way. My aim is to write an html page to a PDF file using win2pdf - but via ASP/vbscript/javascript rather than with manual intervention. The script for doing this was provided by win2PDF's tech support but when it did not work, that was the limit of their understanding. In the sample script the file ascii.asp just produces a table of ascii codes/characters. The URL given is on my own PC which has IIS set up to run scripts which it does fine. The error I get occurs on about the fourth line executed. I am logged in with full admin rights - I think! But I'm no expert. I hope this helps to give some more specific suggestions about how to check/fix the admin rights.

  Read the article

• Providing DNS redirection to honeypot server for known bad domains

  - by syn-

  Currently running BIND on RHEL 5.4 and am looking for a more efficient manner of providing DNS redirection to a honeypot server for a large (30,000+) list of forbidden domains. Our current solution for this requirement is to include a file containing a zone master declaration for each blocked domain in named.conf. Subsequently, each of these zone declarations point to the same zone file, which resolves all hosts in that domain to our honeypot servers. ...basically this allows us to capture any "phone home" attempts by malware that may infiltrate the internal systems. The problem with this configuration is the large amount of time taken to load all 30,000+ domains as well as management of the domain list configuration file itself... if any errors creep into this file, the BIND server will fail to start, thereby making automation of the process a little frightening. So I'm looking for something more efficient and potentially less error prone. named.conf entry: include "blackholes.conf"; blackholes.conf entry example: zone "bad-domain.com" IN { type master; file "/var/named/blackhole.zone"; allow-query { any; }; notify no; }; blackhole.zone entries: $INCLUDE std.soa @ NS ns1.ourdomain.com. @ NS ns2.ourdomain.com. @ NS ns3.ourdomain.com.                        IN            A                192.168.0.99 *                      IN            A                192.168.0.99

  Read the article

• Areca 1280ml RAID6 volume set failed

  - by Richard

  Today we hit some kind of worst case scenario and are open to any kind of good ideas. Here is our problem: We are using several dedicated storage servers to host our virtual machines. Before I continue, here are the specs: Dedicated Server Machine Areca 1280ml RAID controller, Firmware 1.49 12x Samsung 1TB HDDs We configured one RAID6-set with 10 discs that contains one logical volume. We have two hot spares in the system. Today one HDD failed. This happens from time to time, so we replaced it. Upon rebuilding a second disc failed. Normally this is no fun. We stopped heavy IO-operations to ensure a stable RAID rebuild. Sadly the hot-spare disc failed while rebuilding and the whole thing stopped. Now we have the following situation: The controller says that the raid set is rebuilding The controller says that the volume failed It is a RAID 6 system and two discs failed, so the data has to be intact, but we cannot bring the volume online again to access the data. While searching we found the following leads. I don't know whether they are good or bad: Mirroring all the discs to a second set of drives. So we would have the possibility to try different things without loosing more than we already have. Trying to rebuild the array in R-Studio. But we have no real experience with the software. Pulling all drives, rebooting the system, changing into the areca controller bios, reinserting the HDDs one-by-one. Some people are saying that the brought the system online by this. Some are saying that the effect is zero. Some say, that they blew the whole thing. Using undocumented areca commands like "rescue" or "LeVel2ReScUe". Contacting a computer forensics service. But whoa... primary estimates by phone exceeded 20.000€. That's why we would kindly ask for help. Maybe we are missing the obvious? And yes of course, we have backups. But some systems lost one week of data, thats why we'd like to get the system up and running again. Any help, suggestions and questions are more than welcome.

  Read the article

• Building NanoBSD inside a jail

  - by ptomli

  I'm trying to setup a jail to enable building a NanoBSD image. It's actually a jail on top of a NanoBSD install. The problem I have is that I'm unable to mount the md device in order to do the 'build image' part. Is it simply not possible to mount an md device inside a jail, or is there some other knob I need to twiddle? On the host /etc/rc.conf.local jail_enable="YES" jail_mount_enable="YES" jail_list="build" jail_set_hostname_allow="NO" jail_build_hostname="build.vm" jail_build_ip="192.168.0.100" jail_build_rootdir="/mnt/zpool0/jails/build/home" jail_build_devfs_enable="YES" jail_build_devfs_ruleset="devfsrules_jail_build" /etc/devfs.rules [devfsrules_jail_build=5] # nothing Inside the jail [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# sysctl security.jail security.jail.param.cpuset.id: 0 security.jail.param.host.hostid: 0 security.jail.param.host.hostuuid: 64 security.jail.param.host.domainname: 256 security.jail.param.host.hostname: 256 security.jail.param.children.max: 0 security.jail.param.children.cur: 0 security.jail.param.enforce_statfs: 0 security.jail.param.securelevel: 0 security.jail.param.path: 1024 security.jail.param.name: 256 security.jail.param.parent: 0 security.jail.param.jid: 0 security.jail.enforce_statfs: 1 security.jail.mount_allowed: 1 security.jail.chflags_allowed: 1 security.jail.allow_raw_sockets: 0 security.jail.sysvipc_allowed: 0 security.jail.socket_unixiproute_only: 1 security.jail.set_hostname_allowed: 0 security.jail.jail_max_af_ips: 255 security.jail.jailed: 1 [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# mdconfig -l md2 md0 md1 md0 and md1 are the ramdisks of the host. bsdlabel looks sensible [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# bsdlabel /dev/md2s1 # /dev/md2s1: 8 partitions: # size offset fstype [fsize bsize bps/cpg] a: 1012016 16 4.2BSD 0 0 0 c: 1012032 0 unused 0 0 # "raw" part, don't edit newfs runs ok [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# newfs -U /dev/md2s1a /dev/md2s1a: 494.1MB (1012016 sectors) block size 16384, fragment size 2048 using 4 cylinder groups of 123.55MB, 7907 blks, 15872 inodes. with soft updates super-block backups (for fsck -b #) at: 160, 253184, 506208, 759232 mount fails [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# mount /dev/md2s1a _.mnt/ mount: /dev/md2s1a : Operation not permitted UPDATE: One of my colleagues pointed out There are some file systems types that can't be securely mounted within a jail no matter what, like UFS, MSDOFS, EXTFS, XFS, REISERFS, NTFS, etc. because the user mounting it has access to raw storage and can corrupt it in a way that it will panic entire system. From http://www.mail-archive.com/[email protected]/msg160389.html So it seems that the standard nanobsd.sh won't run inside a jail while it uses the md device to build the image. One potential solution I'll try is to chroot from the host into the build jail, rather than jexec a shell.

  Read the article

< Previous Page | 239 240 241 242 243 244 245 246 247 248 249 250  | Next Page >