Search Results

Search found 22668 results on 907 pages for 'command prompt'.

Page 247/907 | < Previous Page | 243 244 245 246 247 248 249 250 251 252 253 254  | Next Page >

  • How To Specify Bitrate, Codec and Demultiplexing for VLC Video Capture or Recording

    - by Subhash
    I capture video from old TV tuner card - Pinnacle PCTV - using VLC. The video is from the Composite input and audio is from I guess the mixer or Line in. The command I use is: vlc v4l2:///dev/video0:normal=pal:width=720:height=576:input=1 :input-slave="alsa://hw:0,0" In VLC, I have enabled the Advanced Controls toolbar, which allows me to record videos when I want to. However, these videos are uncompressed - very big and play only with VLC. Totem throws the "Could not demultiplex stream" error. I need to convert them using WinFF to reduce their size and make them playable with Totem and other software. My question is whether I can configure the recording settings - the codecs and the bitrate, and also get the stream demultiplexed. If I pass any -sout parameter with command I get a "Segmentation fault". I use 64-bit Ubuntu 10.10.

    Read the article

  • What to do after a servicing fails on TFS 2010

    - by Martin Hinshelwood
    What do you do if you run a couple of hotfixes against your TFS 2010 server and you start to see seem odd behaviour? A customer of mine encountered that very problem, but they could not just, or at least not easily, go back a version.   You see, around the time of the TFS 2010 launch this company decided to upgrade their entire 250+ development team from TFS 2008 to TFS 2010. They encountered a few problems, owing mainly to the size of their TFS deployment, and the way they were using TFS. They were not doing anything wrong, but when you have the largest deployment of TFS outside of Microsoft you tend to run into problems that most people will never encounter. We are talking half a terabyte of source control in TFS with over 80 proxy servers. Its certainly the largest deployment I have ever heard of. When they did their upgrade way back in April, they found two major flaws in the product that meant that they had to back out of the upgrade and wait for a couple of hotfixes. KB983504 – Hotfix KB983578 – Patch KB2401992 -Hotfix In the time since they got the hotfixes they have run 6 successful trial migrations, but we are not talking minutes or hours here. When you have 400+ GB of data it takes time to copy it around. It takes time to do the upgrade and it takes time to do a backup. Well, last week it was crunch time with their developers off for Christmas they had a window of opportunity to complete the upgrade. Now these guys are good, but they wanted Northwest Cadence to be available “just in case”. They did not expect any problems as they already had 6 successful trial upgrades. The problems surfaced around 20 hours in after the first set of hotfixes had been applied. The new Team Project Collection, the only thing of importance, had disappeared from the Team Foundation Server Administration console. The collection would not reattach either. It would not even list the new collection as attachable! Figure: We know there is a database there, but it does not This was a dire situation as 20+ hours to repeat would leave the customer over time with 250+ developers sitting around doing nothing. We tried everything, and then we stumbled upon the command of last resort. TFSConfig Recover /ConfigurationDB:SQLServer\InstanceName;TFS_ConfigurationDBName /CollectionDB:SQLServer\instanceName;"Collection Name" -http://msdn.microsoft.com/en-us/library/ff407077.aspx WARNING: Never run this command! Now this command does something a little nasty. It assumes that there really should not be anything wrong and sets about fixing it. It ignores any servicing levels in the Team Project Collection database and forcibly applies the latest version of the schema. I am sure you can imagine the types of problems this may cause when the schema is updated leaving the data behind. That said, as far as we could see this collection looked good, and we were even able to find and attach the team project collection to the Configuration database. Figure: After attaching the TPC it enters a servicing mode After reattaching the team project collection we found the message “Re-Attaching”. Well, fair enough that sounds like something that may need to happen, and after checking that there was disk IO we left it to it. 14+ hours later, it was still not done so the customer raised a priority support call with MSFT and an engineer helped them out. Figure: Everything looks good, it is just offline. Tip: Did you know that these logs are not represented in the ~/Logs/* folder until they are opened once? The engineer dug around a bit and listened to our situation. He knew that we had run the dreaded “tfsconfig restore”, but was not phased. Figure: This message looks suspiciously like the wrong servicing version As it turns out, the servicing version was slightly out of sync with the schema. KB Schema Successful           KB983504 341 Yes   KB983578 344 sort of   KB2401992 360 nope   Figure: KB, Schema table with notation to its success The Schema version above represents the final end of run version for that hotfix or patch. The only way forward The problem was that the version was somewhere between 341 and 344. This is not a nice place to be in and the engineer give us the  only way forward as the removal of the servicing number from the database so that the re-attach process would apply the latest schema. if his sounds a little like the “tfsconfig recover” command then you are exactly right. Figure: Sneakily changing that 3 to a 1 should do the trick Figure: Changing the status and dropping the version should do it Now that we have done that we should be able to safely reattach and enable the Team Project Collection. Figure: The TPC is now all attached and running You may think that this is the end of the story, but it is not. After a while of mulling and seeking expert advice we came to the opinion that the database was, for want of a better term, “hosed”. There could well be orphaned data in there and the likelihood that we would have problems later down the line is pretty high. We contacted the customer back and made them aware that in all likelihood the repaired database was more like a “cut and shut” than anything else, and at the first sign of trouble later down the line was likely to split in two. So with 40+ hours invested in getting this new database ready the customer threw it away and started again. What would you do? Would you take the “cut and shut” to production and hope for the best?

    Read the article

  • How to install an older version of Java

    - by Alex Spurling
    I updated my installation of the sun-java6-jdk package today to version 6.24-1build0.10.10.1 after being prompted by the update manager. However this now causes some compilation failures so I'd like to revert back to the previous version that I had installed. I've tried using Synaptic but the 'Force Version' menu command is disabled. I've tried the following command to install the previous version sudo apt-get install sun-java6-jdk=6.22-0ubuntu1~10.10 But I'm not sure that I have the correct version: Reading package lists... Done Building dependency tree Reading state information... Done E: Version ‘6.22-0ubuntu1~10.10’ for ‘sun-java6-jdk’ was not found I've taken this version number from this changelog: https://launchpad.net/ubuntu/+source/sun-java6/+changelog Is this the correct way to install a previous version of a package? Have I got the correct version from the sun-java6 change log?

    Read the article

  • java.net.SocketException: Connection reset; No available router to destination

    - by adejuanc
    Sometimes a Weblogic Server will be unreachable, there could be several reasons, the server is hang, down, and thus not responding to a ping, or it could be related to a network issue.A possible point of failure in the network layer are firewalls. You should contact your network team if you have following messages: java weblogic.Admin -adminurl t3://adminServer.mydomain.com:7777 -username admin -password lockdown PINGFailed to connect to t3://adminServer.mydomain.com:7777: Destination unreachable; nested exception is:java.net.SocketException: Connection reset; No available router to destination A possible work around for the ping command is to use the HTTP protocol, instead of the t3 protocol. To enable this you must configure WebLogic to do HTTP tunneling. To enable, access the administration console, click servers-> server you want to reach-> protocols -> http -> enable Tunneling. no restart is necessary. And then, following command will work: java weblogic.Admin -adminurl http://adminServer.mydomain.com:7777 -username igmadmin -password l0ckdown PING

    Read the article

  • How to workaround or diagnose a kernel panic when "safely removing" external hdd?

    - by Shawn
    I'm experiencing an issue when using the "Safely Remove" option to remove my 1TB external HDD from the Unity Launcher. Not every time, but occasionally my screen will go black and display LARGE amounts of text information (which I obviously cannot screen cap). The jist of the info displayed is that unmounting or 'safely removing' the drive causes a kernel panic. Is there a Command Line command to remove mounted drives, or at least one that would show me some sort of error output when the drive is removed? I'm trying to narrow down the cause. I could be imagining this, but it seems to happen most often when I have other programs running when I remove the drive (i.e. Firefox, Transmission). Please note that my external drive is not in use when I attempt to remove it and it is not being used either by Firefox or Transmission at these times. Any help would be appreciated.

    Read the article

  • Remove bottom panel from a remastered LiveCD

    - by Uri Herrera
    How can I remove or autohide to 0 the bottom Gnome panel from a remastered liveCD and autostart AWN (or any dock for that matter...) to replace it? , just as moonOS 4 (the distro that gave me the idea to try to do this) Using this command to enable the auto hide gconftool-2 -t bool -s /apps/panel/default_setup/toplevels/bottom_panel/auto_hide "true" i Figured out how to Autostart AWN,however that involves removing BOTH panels, so im not quite there yet Using UCK gconf-editor to manually edit the option to auto hide the bottom panel doesn't work, when testing the livecd BOTH panels are still there, even though i use the command and then run gconf-editor to check that the option is eneabled, which it is, however, once the livecd starts the autohide feature is disabled

    Read the article

  • Updated 11.10 - now trackpad and wifi won't work. How can these be fixed?

    - by Aron Standley
    I reinstalled 11.10 on my Asus EEE 1005HA, and my mousepad hasn't been working since. I've tried the workarounds mentioned in this post: http://ubuntuforums.org/showthread.php?t=1867357 but, I get the message on the command line that says, "Synaptic isn't installed." When I go to the network settings to install Synaptic, I can't turn on wifi - no wireless options exist. How can I turn on wifi from the command line, on a new 11.10 install? Or, is there a way to turn on the trackpad and wifi from the install thumb drive? How can I move forward?

    Read the article

  • changing drive nodes & hdparm

    - by Kalamalka Kid
    I am currently attempting to create a command that works at startup to kill the power on two of my very noisy hard drives. I have edited the etc/rc.local file to include this command: sudo hdparm -y /dev/sdc sudo hdparm -y /dev/sdd exit 0 While I think this should work, it seems the allocated drives keep switching around every time I reboot. I have sda, sdb, sdc, sdd, and sde but they keep getting jumbled around (making the drive I wish to shut different than sdd which is making the task of shutting down the right drive on start-up quite cumbersome. I had a perfectly functioning ftstab file working which disappeard, but I restored it from the back up into the etc/ dir: # <file system> <mount point> <type> <options> <dump> <pass> #Entry for /dev/sda1 : UUID=43c09daf-08a5-44f2-89b0-fc7c6f0d1e67 / ext4 errors=remount-ro 0 1 #Entry for /dev/sdd1 : UUID=443AFBAD7FE50945 /media/DX100 ntfs-3g defaults,nosuid,nodev,locale=en_CA.UTF-8 0 0 #Entry for /dev/sdb1 : UUID=FCE456F5E456B21E /media/GalaxyM83 ntfs-3g defaults,nosuid,nodev,locale=en_CA.UTF-8 0 0 #Entry for /dev/sdf1 : UUID=1CA057FDA057DBB8 /media/Holideck ntfs-3g defaults,nosuid,nodev,locale=en_CA.UTF-8 0 0 #Entry for /dev/sdc1 : UUID=7ABB49654B799D40 /media/JX3P ntfs defaults,nosuid,nodev,locale=en_CA.UTF-8 0 0 it seems every time I boot the order of the drives changes. I do not know how to resolve this. A quick workaround the problem was to go with UUID instead of the DEV letter by editing the etc/rc.local file to include: hdparm -y /dev/disk/by-uuid/443AFBAD7FE50945 hdparm -y /dev/disk/by-uuid/7ABB49654B799D40 So I thought I was in the clear, as I heard both hard drives die down during the boot sequence, BUT, as soon as I log in both drives start up again! so now I have to figure out what is making them start up again after log in, or perhaps another way to get them to turn off. Is there some kind of command i can get to execute after log in? I tried editing the startup applications to include an autossh with: autoshh - sudo hdparm -y /dev/disk/by-uuid/7ABB49654B799D40 autoshh - sudo hdparm -y /dev/disk/by-uuid/443AFBAD7FE50945 but this did not seem to work to turn off the disks after log in.

    Read the article

  • SCHA API for resource group failover / switchover history

    - by krishna.k.murthy
    The Oracle Solaris Cluster framework keeps an internal log of cluster events, including switchover and failover of resource groups. These logs can be useful to Oracle support engineers for diagnosing cluster behavior. However, till now, there was no external interface to access the event history. Oracle Solaris Cluster 4.2 provides a new API option for viewing the recent history of resource group switchovers in a program-parsable format. Oracle Solaris Cluster 4.2 provides a new option tag argument RG_FAILOVER_LOG for the existing API command scha_cluster_get which can be used to list recent failover / switchover events for resource groups. The command usage is as shown below: # scha_cluster_get -O RG_FAILOVER_LOG number_of_days number_of_days : the number of days to be considered for scanning the historical logs. The command returns a list of events in the following format. Each field is separated by a semi-colon [;]: resource_group_name;source_nodes;target_nodes;time_stamp source_nodes: node_names from which resource group is failed over or was switched manually. target_nodes: node_names to which the resource group failed over or was switched manually. There is a corresponding enhancement in the C API function scha_cluster_get() which uses the SCHA_RG_FAILOVER_LOG query tag. In the example below geo-infrastructure (failover resource group), geo-clusterstate (scalable resource group), oracle-rg (failover resource group), asm-dg-rg (scalable resource group) and asm-inst-rg (scalable resource group) are part of Geographic Edition setup. # /usr/cluster/bin/scha_cluster_get -O RG_FAILOVER_LOG 3 geo-infrastructure;schost1c;;Mon Jul 21 15:51:51 2014 geo-clusterstate;schost2c,schost1c;schost2c;Mon Jul 21 15:52:26 2014 oracle-rg;schost1c;;Mon Jul 21 15:54:31 2014 asm-dg-rg;schost2c,schost1c;schost2c;Mon Jul 21 15:54:58 2014 asm-inst-rg;schost2c,schost1c;schost2c;Mon Jul 21 15:56:11 2014 oracle-rg;;schost2c;Mon Jul 21 15:58:51 2014 geo-infrastructure;;schost2c;Mon Jul 21 15:59:19 2014 geo-clusterstate;schost2c;schost2c,schost1c;Mon Jul 21 16:01:51 2014 asm-inst-rg;schost2c;schost2c,schost1c;Mon Jul 21 16:01:10 2014 asm-dg-rg;schost2c;schost2c,schost1c;Mon Jul 21 16:02:10 2014 oracle-rg;schost2c;;Tue Jul 22 16:58:02 2014 oracle-rg;;schost1c;Tue Jul 22 16:59:05 2014 oracle-rg;schost1c;schost1c;Tue Jul 22 17:05:33 2014 Note that in the output some of the entries might have an empty string in the source_nodes. Such entries correspond to events in which the resource group is switched online manually or during a cluster boot-up. Similarly, an empty destination_nodes list indicates an event in which the resource group went offline. - Arpit Gupta, Harish Mallya

    Read the article

  • MOSS 2007 WSP Retraction 'Error"

    - by juanlarios
    This one is a quick post , but I thought I would post this information as I could not find anything that helped me on this specific scenario. Please read the entire article before taking action as there are some irreversable or very troublesome routes I caution about! Problem: I had a client trying to retract a WSP from Central Admin and would eventually go to an, 'Error' State. I could not retract it and after looking at event logs I figured it was a problem with security. I tried several accounts, checked the databases to see if there was some issue with readonly databases and nothing was working.   Solution: Delete the solution from central admin! Yes, I said it. With StsAdm , just delete the solution from Central Admin using this command: "C:\Program Files\Common Files\Microsoft Shared\web server extensions\12\BIN\STSADM.exe" -o deletesolution -name "yoursolution.wsp" What has just happened is that Central Admin does not know about the WSP anymore but the feature and any deployed files are still on the server. For whatever reason SharePoint was not able to retract the files as it normally does. Now you can do one of two things, you can add the solution again to central admin and deploy overtop of the deployed files so it overrides them, or simply clean up the files manually. I re-added the solution through stsadm, but then deployed through stsadm using the -force option in the command. This overrides the existing files on the server. If you deploy through Central admin it will tell you you need the -force option that is not offered as part of the UI in central admin. Use the following command: "C:\Program Files\Common Files\Microsoft Shared\web server extensions\12\BIN\STSADM.exe" -o deploysolution -name "YourSolution.wsp" -immediate -allowgacdeployment -force Just to make sure everything was good, I retracted to solution again, and it worked! then I deleted the solution from central admin alltogether. Then I checked the server and noticed all the files that were deployed with the WSP were cleaned up properly. I then re-added the new WSP the client was looking to install (an Updated WSP). Conclusion: I have no idea why it was not able to retract, but I have seen this several times. I don't know if has to do with security of certain accounts. Althought it's anoying at times, it is fairly easy to fix if you have good instructions. Hope it helps you out!   ***WORD OF CAUTION - if you clean up the files manually you might want to uninstall the features through STSADM commands as SharePOint might still recognize the features that were deployed as the WSP. You might not want to get into the mess of deleting files that are still part of activated or installed Features. THis is why I suggest doing what I did.

    Read the article

  • Scripting with variables from file

    - by Nooster
    I have several videos on my PC that I would like to shorten. For instance I have a 30 sec video where I want to have the section from sec 15 to 20 (a 5sec video). To cut this, I use avconv. avconv -i input.mp4 -ss 15 -acodec copy -vcodec copy -t 5 output.mp4 This command works pretty well. I have many videos I want to cut the same way. This is why I created a textfile containing the information: input-name, start of cut, length of cut, output-name. Those are written into in.txt that looks like this: input.mp4 15 5 output.mp4 input1.mp4 32 10 output1.mp4 input2.mp4 10 7 output2.mp4 ... My question is: How do I have to modify the avconv-command to cut my videos automatically? What I tried was this, but it didn't work at all: avconv -i $1 -ss $2 -acodec copy -vcodec copy -t $3 $4 < in.txt Any idea?

    Read the article

  • How to properly set up Sun's JDK?

    - by jurchiks
    I'm trying to manually install the Sun JDK package (I have my reasons, don't bother asking why). I've successfully extracted the .bin file into /usr/lib/jvm/jdk1.6.0_23, but the problem is the PATH variable. I added this line to the /etc/environment file: JAVA_HOME="/usr/lib/jvm/jdk1.6.0_23" and added JAVA_HOME/bin to the PATH variable, BUT the OS still doesn't recognise the command java, says it's not installed and offers me gcj and openjdk. There was another way by using java-package and converting the .bin to .deb installer, but unfortunately that package is not available on/for maverick, so I can't do it that way. How can I make the PATH variable work and is there anything else required apart from the environment variables to make it all work? When I try to use the update-java-alternatives -l command, it says the following: awk: cannot open /usr/lib/jvm/*.jinfo (No such file or directory) jdk1.6.0_23 /usr/lib/jvm/jdk1.6.0_23 What should be the name of the file and the contents of it?

    Read the article

  • Printer State: Idle - /usr/lib/cups/backend/dnssd failed

    - by bilbo88
    A printer was installed and worked but does not now. A job is successfully submitted, but keeps waiting there for printing (as seen from lpq command). Ping to printer works fine. (The printer is on and works as it prints from Windows.) But on the Printer Property, it shows Printer State: Idle - /usr/lib/cups/backend/dnssd failed. The following command does not help either. sudo service avahi-daemon restart Does any one has a solution? Thank you for help.

    Read the article

  • Can't install Oracle J2EE due to "An internal Error has occurred"

    - by Gabriel Mendez
    I am trying to install Oracle JavaEE 6 SDK with Glassfish on Ubuntu 12.04 with Java SDK 7. I have downloaded java_ee_sdk-6u4-jdk7-linux-x64.sh already, but when I run it on terminal, the wizard appears, and after few steps, I get an Error Message Dialog: An internal Error has occurred. Please contact your system administrator... null. And, the terminal is showing something like WARNING: Could not process a navigation event for command=AC_NEXT [Command=AC_NEXT Error=null ] What can I do? How can I install J2EE/Glassfish under linux x64?

    Read the article

  • Python response parse [migrated]

    - by Pavel Shevelyov
    When I'm sending some data on host: r = urllib2.Request(url, data = data, headers = headers) page = urllib2.urlopen(r) print page.read() I have something like this: [{"command":"settings","settings":{"basePath":"\/","ajaxPageState":{"theme":"spsr","theme_token":"kRHUhchUVpxAMYL8Y8IoyYIcX0cPrUstziAi8gSmMYk","css":[]},"ajax":{"edit-submit":{"callback":"spsr_calculator_form_ajax","wrapper":"calculator_form","method":"replaceWith","event":"mousedown","keypress":true,"url":"\/ru\/system\/ajax","submit":{"_triggering_element_name":"submit"}}}},"merge":true},{"command":"insert","method":null,"selector":null,"data":"\u003cdiv id=\"calculator_form\"\u003e\u003cform action=\"\/ru\/service\/calculator\" method=\"post\" id=\"spsr-calculator-form\" accept-charset=\"UTF-8\"\u003e\u003cdiv\u003e\u003cinput id=\"edit-from-ship-region-id\" type=\"hidden\" name=\"from_ship_region_id\" value=\"\" \/\u003e\n\u003cinput type=\"hidden\" name=\"form_build_id\" value=\"form-0RK_WFli4b2kUDTxpoqsGPp14B_0yf6Fz9x7UK-T3w8\" \/\u003e\n\u003cinput type=\"hidden\" name=\"form_id\" value=\"spsr_calculator_form\" \/\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"bg_p\"\u003e \n\u0421\u0435\u0439\u0447\u0430\u0441 \u0412\u044b... bla bla bla but I want have something, like this: <html><h1>bla bla bla</h1></html> How can I do it?

    Read the article

  • Installing XAMPP in Xubuntu 13.10

    - by illage2
    I downloaded the XAMPP .run file from Apacheandfriends but the installation isn't working for me. I can't seem to navigate to my downloads folder and it just keeps saying command not found all the time. root@john-Aspire-V3-531:/home/john# cd ~/downloads bash: cd: /root/downloads: No such file or directory root@john-Aspire-V3-531:/home/john# cd ~/Downloads bash: cd: /root/Downloads: No such file or directory root@john-Aspire-V3-531:/home/john# /downloads bash: /downloads: No such file or directory root@john-Aspire-V3-531:/home/john# cd /downloads bash: cd: /downloads: No such file or directory root@john-Aspire-V3-531:/home/john# cd downloads bash: cd: downloads: No such file or directory root@john-Aspire-V3-531:/home/john# downloads downloads: command not found What do I need to do? Apacheandfriends says to: chmod 755 xampp-linux-1.8.2-0-installer.run and then ./xampp-linux-1.8.2-0-installer.run but it doesn't seem to think that the file exists. Can anyone help me?

    Read the article

  • How can I find files quicker than find or locate?

    - by Chaitanya
    I have been using find command to find files on my 1 tb hard disk. it takes very long. then I used locate which proved to be faster with regular update using updatedb. But the limitation of locate is that I cannot find files with certain size or modified/created time. can you suggest me any ideas on how to find files at more speed or in that case how to pipe output of locate command in a way that all other information like size, time, etc. can be displayed or redirected to a file.

    Read the article

  • How to totaly remove blank screen screensaver?

    - by Xamidovic
    I have no screensaver installed but when I watch movies after a while blank screen comes and I have to get up every time and move mouse to continue watching the movie. It really pisses me off. I found this command "gsettings set org.gnome.desktop.screensaver idle-activation-enabled false" which allegedly disables blank screen... I put that command in once, and blank screen keeps doing its crap. I did it again, blank screen still works on its own and would not stop. Did it trice, and nothing. Please someone help me with this, I'm freaking out when trying to watch a decent movie. I'd have to mention that I once had "xscreensaver" installed but I removed it after awhile. Don't know if it has something to do with blank screen still work, maybe some else would know. PLEASE HELP !

    Read the article

  • Finding files at more speed

    - by Chaitanya
    I have been using find command to find files on my 1 tb hard disk. it takes very long. then I used locate which proved to be faster with regular update using updatedb. But the limitation of locate is that I cannot find files with certain size or modified/created time. can you suggest me any ideas on how to find files at more speed or in that case how to pipe output of locate command in a way that all other information like size, time, etc. can be displayed or redirected to a file.

    Read the article

  • Why is my mdadm raid-1 recovery so slow?

    - by dimmer
    On a system I'm running Ubuntu 10.04. My raid-1 restore started out fast but quickly became ridiculously slow (at this rate the restore will take 150 days!): dimmer@paimon:~$ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdc1[2] sdb1[1] 1953513408 blocks [2/1] [_U] [====>................] recovery = 24.4% (477497344/1953513408) finish=217368.0min speed=113K/sec unused devices: <none> Eventhough I have set the kernel variables to reasonably quick values: dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_min 1000000 dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_max 100000000 I am using 2 2.0TB Western Digital Hard Disks, WDC WD20EARS-00M and WDC WD20EARS-00J. I believe they have been partitioned such that their sectors are aligned. dimmer@paimon:/sys$ sudo parted /dev/sdb GNU Parted 2.2 Using /dev/sdb Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00M (scsi) Disk /dev/sdb: 2000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 (parted) unit s (parted) p Number Start End Size File system Name Flags 1 2048s 3907028991s 3907026944s ext4 (parted) q dimmer@paimon:/sys$ sudo parted /dev/sdc GNU Parted 2.2 Using /dev/sdc Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00J (scsi) Disk /dev/sdc: 2000GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 I am beginning to think that I have a hardware problem, otherwise I can't imagine why the mdadm restore should be so slow. I have done a benchmark on /dev/sdc using Ubuntu's disk utility GUI app, and the results looked normal so I know that sdc has the capability to write faster than this. I also had the same problem on a similar WD drive that I RMAd because of bad sectors. I suppose it's possible they sent me a replacement with bad sectors too, although there are no SMART values showing them yet. Any ideas? Thanks. As requested, output of top sorted by cpu usage (notice there is ~0 cpu usage). iowait is also zero which seems strange: top - 11:35:13 up 2 days, 9:40, 3 users, load average: 2.87, 2.58, 2.30 Tasks: 142 total, 1 running, 141 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.2%sy, 0.0%ni, 99.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3096304k total, 1482164k used, 1614140k free, 617672k buffers Swap: 1526132k total, 0k used, 1526132k free, 535416k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 45 root 20 0 0 0 0 S 0 0.0 2:17.02 scsi_eh_0 1 root 20 0 2808 1752 1204 S 0 0.1 0:00.46 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/0 4 root 20 0 0 0 0 S 0 0.0 0:00.17 ksoftirqd/0 5 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 6 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/1 ... dmesg errors, definitely looking like hardware: [202884.000157] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [202884.007015] ata5.00: failed command: FLUSH CACHE EXT [202884.013728] ata5.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [202884.013730] res 40/00:00:ff:59:2e/00:00:35:00:00/e0 Emask 0x4 (timeout) [202884.033667] ata5.00: status: { DRDY } [202884.040329] ata5: hard resetting link [202889.400050] ata5: link is slow to respond, please be patient (ready=0) [202894.048087] ata5: COMRESET failed (errno=-16) [202894.054663] ata5: hard resetting link [202899.412049] ata5: link is slow to respond, please be patient (ready=0) [202904.060107] ata5: COMRESET failed (errno=-16) [202904.066646] ata5: hard resetting link [202905.840056] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [202905.849178] ata5.00: configured for UDMA/133 [202905.849188] ata5: EH complete [203899.000292] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [203899.007096] ata5.00: failed command: IDENTIFY DEVICE [203899.013841] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [203899.013843] res 40/00:00:ff:f9:f6/00:00:38:00:00/e0 Emask 0x4 (timeout) [203899.041232] ata5.00: status: { DRDY } [203899.048133] ata5: hard resetting link [203899.816134] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [203899.826062] ata5.00: configured for UDMA/133 [203899.826079] ata5: EH complete [204375.000200] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204375.007421] ata5.00: failed command: IDENTIFY DEVICE [204375.014799] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204375.014800] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204375.044374] ata5.00: status: { DRDY } [204375.051842] ata5: hard resetting link [204380.408049] ata5: link is slow to respond, please be patient (ready=0) [204384.440076] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204384.449938] ata5.00: configured for UDMA/133 [204384.449955] ata5: EH complete [204395.988135] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204395.988140] ata5.00: failed command: IDENTIFY DEVICE [204395.988147] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204395.988149] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204395.988151] ata5.00: status: { DRDY } [204395.988156] ata5: hard resetting link [204399.320075] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204399.330487] ata5.00: configured for UDMA/133 [204399.330503] ata5: EH complete

    Read the article

  • Using the full tty real estate with sqlplus

    - by katsumii
    I believe 'rlwrap' is widely used for adding 'sqlplus' the history function and command line editing. 'rlwrap' has other functions and here's my kludgy alias to force sqlplus to use the full real estate of yourtty. Be it PuTTy session from Windows or Linux gnome terminal. $ declare -f sqlplus sqlplus () { PRE_TEXT=$(resize |sed -n "1s/COLUMNS=/set linesize /p;2s/LINES=/set pagesize /p"|while read line; do printf "%s \ " "$line";done); if [ -z "$1" ]; then rlwrap -m -P "$PRE_TEXT" sqlplus /nolog; else if ! echo $1 | grep '^-' > /dev/null; then rlwrap -m -P "$PRE_TEXT connect $*" sqlplus /nolog; else command sqlplus $*; fi; fi }

    Read the article

  • How can I get nvidia-settings to work?

    - by Palace Chan
    I have an ASUS N56VM-TB71 with a GeForce 630M graphics card. I have ubuntu 12.04 and when I vga plugged in a dell monitor, i am able to use it. When I then use my laptops hdmi port to plug in my second monitor, nothing happens, so I went to nvidia-settings and I got the error: You do not appear to be using the NVIDIA X Driver, please run nvidia-xconfig as root and restart the X server. I ran this command and rebooted but I still cannot access nvidia-settings and I keep getting that error even though my /etc/X11/xconf.org is the one that got generated by running that command! What can I do to get around that and use my second monitor as well?

    Read the article

  • Partial Submit vs. Auto Submit

    - by Frank Nimphius
    Partial Submit ADF Faces adds the concept of partial form submit to JavaServer Faces 1.2 and beyond. A partial submit actually is a form submit that does not require a page refresh and only updates components in the view that are referenced from the command component PartialTriggers property. Another option for refreshing a component in response to a partial submit is call AdfContext.getCurrentInstance.addPartialTarget(component_instance_handle_goes_here)in a managed bean. If a form contains required fields that the user left empty invoking the partial submit, then errors are shown for each of the field as the full form gets submitted. Autosubmit An input component that has its autosubmit property set to true also performs a partial submit of the form. However, this time it doesn't submit the entire form but only the component that triggers the submit plus components referenced it in their PartialTriggers property. For example, consider a form that has three input fields inpA, inpB and inpC with autosubmit=true set on inpA and required=true set on inpB and inpC. use case 1: Running the view, entering data into inpA and then tabbing out of the field will submit the content for inpA but not for inpB and inpC. Further more, none of the required field settings on inpB and inpC causes an error. use case 2: You change the configuration of inpC and set its PartialTriggers property to point to the ID of component inpA. When rerunning the sample, entering a value into inpA and tabbing out of the field will now submit the inpA and inpC fields and thus show an error for the missing required value on inpC. Internally, using autosubmit=true on an input component sets the event root to just this field, which good to have in case of dependent field validation or behavior. The event root can extended to include other components by using the Partial Triggers property on these components to point to the input field that has autosubmit=true defined. PartialSubmit vs. AutoSubmit Partial submit set on a command component submits the whole form and leaves it to the developer to decide which UI component is refreshed in response. Client side required field validation (as well as the server side equivalent) is not disabled by executed in this scenario. Setting immediate=true on the command item to skip validation doesn't help as it would also skip the model update. Auto submit is a functionality on the input components and also performs a partial form submit. However, in addition an event root is defined that narrows the scope for the submitted data and thus the components that are validated on the request. To read more about this topic, see: http://docs.oracle.com/cd/E23943_01/web.1111/b31973/af_lifecycle.htm#CIAHCFJF

    Read the article

  • Live CD has black screen HP DV6

    - by Shaun Killingbeck
    Attempting to install/try ubuntu (11.10, 12.04) on my new laptop, using a liveCD (and tried USB). I get the purple screen (with the man/keyboard at the bottom) and after that the screen flashes bright white before going black. Ubuntu continues to load in the background, with login sound etc but the screen is off. I have tried as many different solutions as I could find including: using nomodestep, xforcevesa, i915.modeset=0, and also now i915.modeset=1 in boot options (seperately): varying consequences, but either I end up at a blinking cursor with no prompt, a command line (startx fails: no screen found), or the original blank screen again Tried booting from VirtualBox - it crashes at the same place the screen would go blank when using a CD/USB tried 11.04: I don't have this problem BUT when trying to install, I get a ubi-partman error 141 (possibly down to the three partitions that came on my laptop... not sure why HP needed there own separate partition for HP Tools...) Model: HP Pavillion DV6 6B08SA Processor: AMD Quad-Core A6-3410MX APU with Radeon HD 6545G2 Dual Graphics (1.6 GHZ 4 MB L2 cache ) Chipset: AMD RS880M Any help would be greatly appreciated. I just want to be able to partition the drive and install Ubuntu. I'm assuming the issue is graphics card related, although I have no confirmation of that. Update: Tried the ?orkarounds on https://wiki.ubuntu.com/X/Troubleshooting/BlankScreen - set gfxpayload=text changed nothing, removing splash did nothing and setting vesafb.nonsense=1 did nothing either. I'd like to be able to collect some log information somehow, but I can't get to a command line from the liveCD. tried using the latest 12.04 beta, same issue tried nomodeset without splash or quiet. get the following (tail of) output before it freezes on that screen: * Starting configure network device security [OK] * Starting configure network device [OK] [ 25.720899] ieee80211 phy0: w1_ops_config: change monitor mode: false (implement) [ 25.720923] ieee80211 phy0: w1_ops_config: change power-save mode: false (implement) * Starting restore sound card(s') mixer state(s) [fail] [ 25.721849] ieee80211 phy0: w1_ops_bss_info_changed: qos enabled: false (implement) * Stopping save kernel messages [OK] * Starting bluetooth [OK] * PulseAudio configured for per-user sessions saned disabled; edit /etc/default/saned [ 25.988016] hci_cmd_timer: hci0 command tx timeout [ 26.207225] bad LUN (0:1) [ 26.223735] bad target number (1:0) [ 26.252111] bad target number (2:0) [ 26.272170] bad target number (3:0) [ 26.300154] bad target number (4:0) [ 26.328162] bad target number (5:0) [ 26.344180] bad target number (6:0) [ 26.368142] bad target number (7:0) * Checking battery state... [OK] * Stopping System V runlevel capability [OK] Does this give any indication of the problem? the false (implement) messages also reappear when I press the power button to ask it to shutdown, followed by a [fail] status for killing remaining processes.

    Read the article

  • Who should control navigation in an MVVM application?

    - by SonOfPirate
    Example #1: I have a view displayed in my MVVM application (let's use Silverlight for the purposes of the discussion) and I click on a button that should take me to a new page. Example #2: That same view has another button that, when clicked, should open up a details view in a child window (dialog). We know that there will be Command objects exposed by our ViewModel bound to the buttons with methods that respond to the user's click. But, what then? How do we complete the action? Even if we use a so-called NavigationService, what are we telling it? To be more specific, in a traditional View-first model (like URL-based navigation schemes such as on the web or the SL built-in navigation framework) the Command objects would have to know what View to display next. That seems to cross the line when it comes to the separation of concerns promoted by the pattern. On the other hand, if the button wasn't wired to a Command object and behaved like a hyperlink, the navigation rules could be defined in the markup. But do we want the Views to control application flow and isn't navigation just another type of business logic? (I can say yes in some cases and no in others.) To me, the utopian implementation of the MVVM pattern (and I've heard others profess this) would be to have the ViewModel wired in such a way that the application can run headless (i.e. no Views). This provides the most surface area for code-based testing and makes the Views a true skin on the application. And my ViewModel shouldn't care if it displayed in the main window, a floating panel or a child window, should it? According to this apprach, it is up to some other mechanism at runtime to 'bind' what View should be displayed for each ViewModel. But what if we want to share a View with multiple ViewModels or vice versa? So given the need to manage the View-ViewModel relationship so we know what to display when along with the need to navigate between views, including displaying child windows / dialogs, how do we truly accomplish this in the MVVM pattern?

    Read the article

< Previous Page | 243 244 245 246 247 248 249 250 251 252 253 254  | Next Page >