Search Results

Search found 6753 results on 271 pages for 'forward declaration'.

Page 247/271 | < Previous Page | 243 244 245 246 247 248 249 250 251 252 253 254  | Next Page >

• vconfig created virtual interface and trunking - is the the interface untagged or tagged for that VLAN ID?

  - by kce

  I am trying to setup an additional VLAN on our Debian-based router/firewall (which exists as a virtual machine on Hyper-V), our core switch (an HP Procurve 5406) and a remote HP ProCurve 2610 that is connected via a WAN Transparent Lan Service (TLS) link. Let's work backwards from the network edge: The Debian server has an external connection attached to eth0. The internal interface is eth1, which is connected directly from our Hyper-V host to the 5406. The port that eth1 is attached to is setup as Trk12. The 2610 is attached to Trk9 (which trunks a whole slew of VLANs - Trk9 is our TLS head). I can successfully ping the management IP addresses for my VLAN from both switches but I cannot ping, from either switch, the virtual interface for my new VLAN on the Debian-base router and firewall. The existing VLAN works fine. What gives? The port eth1 is attached to is a trunk, the existing VLAN (ID 98) is untagged on the trunk, the new VLAN (ID 198) is tagged. VLAN 198 is tagged on Trk9 on the 5406 and on the 2610. I can ping the other switch's management IP (10.100.198.2 and 10.100.198.3) from the other respective switch. That leg of the VLAN works - however I cannot communicate with eth1.198's 10.100.198.1. I feel like I'm missing something elementary but what it is remains illusive to me. I suspect the issue is with the vconfig created eth1.198. It should pass the tagged VLAN 198 packets correct? But they cannot seem to get any further than the 5406. Communication on the existing VLAN 98 works fine. From the Debian box: eth1: eth1 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.0.1 Bcast:10.100.255.255 Mask:255.255.0.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12179786 errors:0 dropped:0 overruns:0 frame:0 TX packets:20210532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1586498028 (1.4 GiB) TX bytes:26154226278 (24.3 GiB) Interrupt:9 Base address:0xec00 eth1.198: eth1.198 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.198.1 Bcast:10.100.198.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1496 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:72 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:3528 (3.4 KiB) # cat /proc/net/vlan/eth1.198: eth1.198 VID: 198 REORDER_HDR: 0 dev->priv_flags: 1 total frames received 0 total bytes received 0 Broadcast/Multicast Rcvd 0 total frames transmitted 72 total bytes transmitted 3528 total headroom inc 0 total encap on xmit 39 Device: eth1 INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: # ip route 10.100.198.0/24 dev eth1.198 proto kernel scope link src 10.100.198.1 206.174.64.0/20 dev eth0 proto kernel scope link src 206.174.66.14 10.100.0.0/16 dev eth1 proto kernel scope link src 10.100.0.1 default via 206.174.64.1 dev eth0 # iptables -L -v Chain INPUT (policy DROP 6875 packets, 637K bytes) pkts bytes target prot opt in out source destination 41 4320 ACCEPT all -- lo any anywhere anywhere 11481 1560K ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 107 8058 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- eth1 any 10.100.0.0/24 anywhere tcp dpt:ssh 701 317K ACCEPT udp -- eth1 any anywhere anywhere udp dpts:bootps:bootpc Chain FORWARD (policy DROP 1 packets, 40 bytes) pkts bytes target prot opt in out source destination 156K 25M ACCEPT all -- eth1 any anywhere anywhere 215K 248M ACCEPT all -- eth0 eth1 anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1.198 any anywhere anywhere 0 0 ACCEPT all -- eth0 eth1.198 anywhere anywhere state RELATED,ESTABLISHED Chain OUTPUT (policy ACCEPT 13048 packets, 1640K bytes) pkts bytes target prot opt in out source destination From the 5406: # show vlan ports trk12 detail Status and Counters - VLAN Information - for ports Trk12 VLAN ID Name | Status Voice Jumbo Mode ------- -------------------- + ---------- ----- ----- -------- 98 WIFI | Port-based No No Untagged 198 VLAN198 | Port-based No No Tagged

  Read the article

• Server Cabinet/Room Cooling

  - by user37226

  Hello all. I currently have two desktops and three servers in my office sitting on the floor (I know this is bad). With that many servers the ambient temperature in the room goes up quickly. I am located in Dallas, TX so during the winter, if the heat is kept low, it is not a problem, but during the summer it easily jumps the room +10 degrees. I have decided and found a free 42U server cabinet that a hosting company was throwing away to house all of these systems in. One server is in a rack mount case while the other four servers are housed in mid-tower cases. I have purchased shelves for each computer and plan to lay the towers side ways on these shelves (as replacing the cases costs a heck of a lot of money). I like the idea of housing all of these systems in the cabinet because it will save a lot of room and clean up all of the cabling currently laying all over the office floor. When putting this setup together over the next couple of weeks, I want to address issues with dust and cooling. The server cabinet has a fan on top, front plexiglass door and a rear metal door with vent wholes on the bottom. First the cooling issues. I know I am going to want to have cool air enter the bottom of the cabinet and exit the top. I do not want the room heating up though as this will make my work area hot and then make the servers warmer as the air eventually reenters the cabinet. I had an idea to fix this problem, but am unsure if it will work. I was thinking of taking flexible piping and adapting it to the back fans of the computer having the other end of the pipe at the top close to the cabinet's top mounted fan. I was then thinking of creating a duct around the top fan into the attic. Now I am very concerned that the attic will cause issues with this type of setup because during July/August time frame, the attic is easily 120 degrees F. I could also use the flexible pipe to take it to an attic exhaust vent if it would be better to vent it into the 100 degree air outside (at least there may be wind. The other option would be to buy a small portable air conditioner. This may be a possibility, but do I want to spend the extra money on power? I bet this increases the noise. Plus they are around $250 on Amazon. What would you all recommend? Depending on the solution I end up running with above, I would also like to limit the dust that gets into the cabinet. If I were to cut a whole and mount a second cabinet fan on the bottom of the rear door, could I possibly mount a standard home air filter on the other side of that whole? Thanks in advance for your recommendations. I look forward to reading your interesting ideas.

  Read the article

• Server Cabinet/Room Cooling

  - by user37226

  Hello all. I currently have two desktops and three servers in my office sitting on the floor (I know this is bad). With that many servers the ambient temperature in the room goes up quickly. I am located in Dallas, TX so during the winter, if the heat is kept low, it is not a problem, but during the summer it easily jumps the room +10 degrees. I have decided and found a free 42U server cabinet that a hosting company was throwing away to house all of these systems in. One server is in a rack mount case while the other four servers are housed in mid-tower cases. I have purchased shelves for each computer and plan to lay the towers side ways on these shelves (as replacing the cases costs a heck of a lot of money). I like the idea of housing all of these systems in the cabinet because it will save a lot of room and clean up all of the cabling currently laying all over the office floor. When putting this setup together over the next couple of weeks, I want to address issues with dust and cooling. The server cabinet has a fan on top, front plexiglass door and a rear metal door with vent wholes on the bottom. First the cooling issues. I know I am going to want to have cool air enter the bottom of the cabinet and exit the top. I do not want the room heating up though as this will make my work area hot and then make the servers warmer as the air eventually reenters the cabinet. I had an idea to fix this problem, but am unsure if it will work. I was thinking of taking flexible piping and adapting it to the back fans of the computer having the other end of the pipe at the top close to the cabinet's top mounted fan. I was then thinking of creating a duct around the top fan into the attic. Now I am very concerned that the attic will cause issues with this type of setup because during July/August time frame, the attic is easily 120 degrees F. I could also use the flexible pipe to take it to an attic exhaust vent if it would be better to vent it into the 100 degree air outside (at least there may be wind. The other option would be to buy a small portable air conditioner. This may be a possibility, but do I want to spend the extra money on power? I bet this increases the noise. Plus they are around $250 on Amazon. What would you all recommend? Depending on the solution I end up running with above, I would also like to limit the dust that gets into the cabinet. If I were to cut a whole and mount a second cabinet fan on the bottom of the rear door, could I possibly mount a standard home air filter on the other side of that whole? Thanks in advance for your recommendations. I look forward to reading your interesting ideas.

  Read the article

• How to Eliminate Tape Backup and Off-site Storage Service?

  - by Daniel Lucas

  PLEASE READ UPDATE AT THE BOTTOM. THANKS! ;) Environment Info (all Windows): 2 sites 30 servers site #1 (3TB of backup data) 5 servers site #2 (1TB of backup data) MPLS backbone tunnel connecting site #1 and site #2 Current Backup Process: Online Backup (disk-to-disk) Site #1 has a server running Symantec Backup Exec 12.5 with four 1TB USB 2.0 disks. BE jobs for full backups run nightly on all servers in site #1 to these disks. Site #2 backs up to a central file server there using software they already had when we purchased them. A BE job pulls that data nightly to site #1 and stores them on said disks. Off-site Backup (tape) Connected to our backup server is a tape drive. BE backs up the external disks to tape once a week which gets picked up by our off-site storage company. Obviously we rotate two tape libraries, one is always here and one is always there. Requirements: Eliminate the need for tape and off-site storage service by doing disk-to-disk at each site and replicating site #1 to site #2 and vice versa. Software based solution as hardware options have been too pricey (ie, SonicWall, Arkeia). Agents for Exchange, SharePoint, and SQL. Some Ideas So Far: Storage DroboPro at each site with an initial 8TB of storage (these are expandable up to 16TB at present). I like these because they are rackmountable, allow disparate drives, and have iSCSI interfaces. They are relatively cheap too. Software Symantec Backup Exec 12.5 already has all the agents and licenses we need. I'd like to keep using it unless there is a better solution, similarly priced, that does everything BE does plus deduplication and replication. Server Because there is no more need for a SCSI adapter (for tape drive) we are going to virtualize our backup server as it is currently the only physical machine save for SQL boxes. Problems: When replicating between sites we want as little data as possible to go across the pipe. There is no deduplication or compression in what I have laid out here so far. The files being replicated are BE's virtual tape libraries from our disk-to-disk backup. Because of this each of those huge files will go across the wire every week because they change every day. And Finally, the Question: Is there any software out there that does deduplication, or at least compression, to handle just our site-to-site replication? Or, looking at our setup, is there any other solution that I am missing that might be cheaper, faster, better? Thanks. Sorry so long. UPDATE 2: I've set a bounty on this question to get it more attention. I'm looking for software that will handle replication of data between two sites using the least amount of data possible (either compression, deduplication, or some other method). Something similar to rsync would work but it needs to be native to Windows and not a port involving shenanigans to get up and running. Prefer a GUI based product and I don't mind shelling out a few bones if it works. Please, answers that meet the above criteria only. If you don't think one exists or if you think I'm being to restrictive keep it to yourself. If after seven days there is no answer at all, so be it. Thanks again everyone. UPDATE 2: I really appreciate everyone coming forward with suggestions. There is no way for me to try all of these before the bounty expires. For now I'm going to let this bounty run out and whoever has the most votes will get the 100 rep points. Thanks again!

  Read the article

• OpenVPN - client-to-client traffic working in one direction but not the other

  - by user42055

  I have the following VPN configuration: +------------+ +------------+ +------------+ | outpost |----------------| kino |----------------| guchuko | +------------+ +------------+ +------------+ OS: FreeBSD 6.2 OS: Gentoo 2.6.32 OS: Gentoo 2.6.33.3 Keyname: client3 Keyname: server Keyname: client1 eth0: 10.0.1.254 eth0: 203.x.x.x eth0: 192.168.0.6 tun0: 192.168.150.18 tun0: 192.168.150.1 tun0: 192.168.150.10 P-t-P: 192.166.150.17 P-t-P: 192.168.150.2 P-t-P: 192.168.150.9 Kino is the server and has client-to-client enabled. All three machines have ip forwarding enabled, by this on the gentoo boxes: net.ipv4.conf.all.forwarding = 1 And this on the FreeBSD box: net.inet.ip.forwarding: 1 In the server's "ccd" directory is the following files: client1: iroute 192.168.0.0 255.255.255.0 client3: iroute 10.0.1.0 255.255.255.0 The server config has these routes configured: push "route 192.168.0.0 255.255.255.0" push "route 10.0.1.0 255.255.255.0" route 192.168.0.0 255.255.255.0 route 10.0.1.0 255.255.255.0 Kino's routing table looks like this: 192.168.150.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 10.0.1.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.0.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.150.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 Outpost's like this: 192.168.150 192.168.150.17 UGS 0 17 tun0 192.168.0 192.168.150.17 UGS 0 2 tun0 192.168.150.17 192.168.150.18 UH 3 0 tun0 And Guchuko's like this: 192.168.150.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 10.0.1.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 192.168.150.9 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 Now, the tests. Pings from Guchuko to Outpost's LAN IP work OK, as does the reverse - pings from Outpost to Guchuko's LAN IP. However... Pings from Outpost, to a machine on Guchuko's LAN work fine: .(( root@outpost )). (( 06:39 PM )) :: ~ :: # ping 192.168.0.3 PING 192.168.0.3 (192.168.0.3): 56 data bytes 64 bytes from 192.168.0.3: icmp_seq=0 ttl=63 time=462.641 ms 64 bytes from 192.168.0.3: icmp_seq=1 ttl=63 time=557.909 ms But a ping from Guchuko, to a machine on Outpost's LAN does not: .(( root@guchuko )). (( 06:43 PM )) :: ~ :: # ping 10.0.1.253 PING 10.0.1.253 (10.0.1.253) 56(84) bytes of data. --- 10.0.1.253 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2000ms Guchuko's tcpdump of tun0 shows: 18:46:27.716931 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 1, length 64 18:46:28.716715 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 2, length 64 18:46:29.716714 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 3, length 64 Outpost's tcpdump on tun0 shows: 18:44:00.333341 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 3, length 64 18:44:01.334073 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 4, length 64 18:44:02.331849 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 5, length 64 So Outpost is receiving the ICMP request destined for the machine on it's subnet, but appears not be forwarding it. Outpost has gateway_enable="YES" in its rc.conf which correctly sets net.inet.ip.forwarding to 1 as mentioned earlier. As far as I know, that's all that's required to make a FreeBSD box forward packets between interfaces. Is there something else I could be forgetting ?

  Read the article

• pptpd not working externally on Ubuntu Server 11.10

  - by Brendan

  I am trying to set up a pptpd vpn on our newly installed Ubuntu 11.10 64 bit server, but am not having success having a client connect via an iPhone to the VPN. Note that no clients have been able to connect to this VPN from outside of the network. The system is up to date with patches. Here is the output of /var/log/syslog. Please note that 222.153.x.y is my remote IP address. Mar 30 22:07:47 server pptpd[9546]: CTRL: Client 222.153.x.y control connection started Mar 30 22:07:47 server pptpd[9546]: CTRL: Starting call (launching pppd, opening GRE) Mar 30 22:07:47 server pppd[9555]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Mar 30 22:07:47 server pppd[9555]: pppd 2.4.5 started by root, uid 0 Mar 30 22:07:47 server pppd[9555]: Using interface ppp0 Mar 30 22:07:47 server pppd[9555]: Connect: ppp0 <--> /dev/pts/3 Mar 30 22:07:47 server pptpd[9546]: GRE: Bad checksum from pppd. Mar 30 22:08:17 server pppd[9555]: LCP: timeout sending Config-Requests Mar 30 22:08:17 server pppd[9555]: Connection terminated. Mar 30 22:08:17 server pppd[9555]: Modem hangup Mar 30 22:08:17 server pppd[9555]: Exit. Mar 30 22:08:17 server pptpd[9546]: GRE: read(fd=6,buffer=6075a0,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Mar 30 22:08:17 server pptpd[9546]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Mar 30 22:08:17 server pptpd[9546]: CTRL: Reaping child PPP[9555] Mar 30 22:08:17 server pptpd[9546]: CTRL: Client 222.153.x.y control connection finished As you can see, the problem seems to be the connection timing out after 30 seconds ("Mar 30 22:08:17 server pppd[9555]: LCP: timeout sending Config-Requests". Over Wifi however (inside the local network) there are no issues: Mar 30 22:12:33 unreal-server pptpd[12406]: CTRL: Client 192.168.0.100 control connection started Mar 30 22:12:33 unreal-server pptpd[12406]: CTRL: Starting call (launching pppd, opening GRE) Mar 30 22:12:33 unreal-server pppd[12407]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Mar 30 22:12:33 unreal-server pppd[12407]: pppd 2.4.5 started by root, uid 0 Mar 30 22:12:33 unreal-server pppd[12407]: Using interface ppp0 Mar 30 22:12:33 unreal-server pppd[12407]: Connect: ppp0 <--> /dev/pts/3 Mar 30 22:12:33 unreal-server pptpd[12406]: GRE: Bad checksum from pppd. Mar 30 22:12:36 unreal-server pppd[12407]: peer from calling number 192.168.0.100 authorized Mar 30 22:12:36 unreal-server pppd[12407]: MPPE 128-bit stateless compression enabled Mar 30 22:12:36 unreal-server pppd[12407]: Cannot determine ethernet address for proxy ARP Mar 30 22:12:36 unreal-server pppd[12407]: local IP address 192.168.0.10 Mar 30 22:12:36 unreal-server pppd[12407]: remote IP address 192.168.1.1 I have set up an iptables config for the server; to check this isn't the problem I allowed all traffic temporarily, but this does NOT change the symptoms in the first example. Here is the output from /etc/iptables.rules.save *filter :FORWARD ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] COMMIT Even with these rules applied, the output from /var/log/syslog is LINE FOR LINE what I saw in the the first block of code. Please note that before running this Ubuntu server; an old SME Server box was running in place of it, that had a pptpd server on it just like we are using, and we experienced no issues.

  Read the article

• nginx : backend https, proxy_pass shows ip

  - by Vulpo

  I am using nginx as a reverse proxy listening at port 80 (http). I am using proxy_pass to forward requests to backend http and https servers. Everything works fine for my http server but when I try to reach the https server through nginx reverse proxy the ip of the https server is shown in the client's web browser. I want the uri of the nginx server to be shown instead of the https backend server's ip (once again, this works fine with the http server but not for the https server). See this post on the forum Here is my configuration file : server { listen 80; server_name domain1.com; access_log off; root /var/www; if ($request_method !~ ^(GET|HEAD|POST)$ ) { return 444; } location / { proxy_pass http://ipOfHttpServer:port/; } } server { listen 80; server_name domain2.com; access_log off; root /var/www; if ($request_method !~ ^(GET|HEAD|POST)$ ) { return 444; } location / { proxy_pass http://ipOfHttpsServer:port/; proxy_set_header X_FORWARDED_PROTO https; #proxy_set_header Host $http_host; } } When I try the "proxy_set_header Host $http_host" directive and "proxy_set_header Host $host" the web page can't be reached (page not found). But when I comment it, the ip of the https server is shown in the browser (which is bad). Does anyone have an idea ? My other configs files are : proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; #proxy_hide_header X-Powered-By; proxy_intercept_errors on; proxy_buffering on; proxy_cache_key "$scheme://$host$request_uri"; proxy_cache_path /var/cache/nginx levels=1:2 keys_zone=cache:10m inactive=7d max_size=700m; user www-data; worker_processes 2; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; access_log /var/log/nginx/access.log; server_names_hash_bucket_size 64; sendfile off; tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_comp_level 5; gzip_http_version 1.0; gzip_min_length 0; gzip_types text/plain text/html text/css image/x-icon application/x-javascript; gzip_vary on; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } Thanks for your help !

  Read the article

• Forwarding rsyslog to syslog-ng, with FQDN and facility separation

  - by Joshua Miller

  I'm attempting to configure my rsyslog clients to forward messages to my syslog-ng log repository systems. Forwarding messages works "out of the box", but my clients are logging short names, not FQDNs. As a result the messages on the syslog repo use short names as well, which is a problem because one can't determine which system the message originated from easily. My clients get their names through DHCP / DNS. I've tried a number of solutions trying to get this working, but without success. I'm using rsyslog 4.6.2 and syslog-ng 3.2.5. I've tried setting $PreserveFQDN on as the first directive in /etc/rsyslog.conf (and restarting rsyslog of course). It seems to have no effect. hostname --fqdn on the client returns the proper FQDN, so the problem isn't whether the system can actually figure out its own FQDN. $LocalHostName <fqdn> looked promising, but this directive isn't available in my version of rsyslog (Available since 4.7.4+, 5.7.3+, 6.1.3+). Upgrading isn't an option at the moment. Configuring the syslog-ng server to populate names based on reverse lookups via DNS isn't an option. There are complexities with reverse DNS and the public cloud. Specifying for the forwarder to use a custom template seems like a viable option at first glance. I can specify the following, which causes local logging to begin using the FQDN on the syslog-ng repo. $template MyTemplate, "%timestamp% <FQDN> %syslogtag%%msg%" $ActionForwardDefaultTemplate MyTemplate However, when I put this in place syslog-ng seems to be unable to categorize messages by facility or priority. Messages come in as FQDN, but everything is put in to user.log. When I don't use the custom template, messages are properly categorized under facility and priority, but with the short name. So, in summary, if I manually trick rsyslog into including the FQDN, priority and facility becomes lost details to syslog-ng. How can I get rsyslog to do FQDN logging which works properly going to a syslog-ng repository? rsyslog client config: $ModLoad imuxsock.so # provides support for local system logging (e.g. via logger command) $ModLoad imklog.so # provides kernel logging support (previously done by rklogd) $ActionFileDefaultTemplate RSYSLOG_TraditionalFileFormat *.info;mail.none;authpriv.none;cron.none /var/log/messages authpriv.* /var/log/secure mail.* -/var/log/maillog cron.* /var/log/cron *.emerg * uucp,news.crit /var/log/spooler local7.* /var/log/boot.log $WorkDirectory /var/spool/rsyslog # where to place spool files $ActionQueueFileName fwdRule1 # unique name prefix for spool files $ActionQueueMaxDiskSpace 1g # 1gb space limit (use as much as possible) $ActionQueueSaveOnShutdown on # save messages to disk on shutdown $ActionQueueType LinkedList # run asynchronously $ActionResumeRetryCount -1 # infinite retries if host is down *.* @syslog-ng1.example.com *.* @syslog-ng2.example.com syslog-ng configuration (abridged for brevity): options { flush_lines (0); time_reopen (10); log_fifo_size (1000); long_hostnames (off); use_dns (no); use_fqdn (yes); create_dirs (no); keep_hostname (yes); }; source src { unix-stream("/dev/log"); internal(); udp(ip(0.0.0.0) port(514)); }; destination per_host_destination { file( "/var/log/syslog-ng/devices/$HOST/$FACILITY.log" owner("root") group("root") perm(0644) dir_owner(root) dir_group(root) dir_perm(0775) create_dirs(yes)); }; log { source(src); destination(per_facility_destination); };

  Read the article

• Router 2wire, Slackware desktop in DMZ mode, iptables policy aginst ping, but still pingable

  - by user135501

  I'm in DMZ mode, so I'm firewalling myself, stealthy all ok, but I get faulty test results from Shields Up that there are pings. Yesterday I couldn't make a connection to game servers work, because ping block was enabled (on the router). I disabled it, but this persists even due to my firewall. What is the connection between me and my router in DMZ mode (for my machine, there is bunch of others too behind router firewall)? When it allows router affecting if I'm pingable or not and if router has setting not blocking ping, rules in my iptables for this scenario do not work. Please ignore commented rules, I do uncomment them as I want. These two should do the job right? iptables -A INPUT -p icmp --icmp-type echo-request -j DROP echo 1 > /proc/sys/net/ipv4/icmp_echo_ignore_all Here are my iptables: #!/bin/sh # Begin /bin/firewall-start # Insert connection-tracking modules (not needed if built into the kernel). #modprobe ip_tables #modprobe iptable_filter #modprobe ip_conntrack #modprobe ip_conntrack_ftp #modprobe ipt_state #modprobe ipt_LOG # allow local-only connections iptables -A INPUT -i lo -j ACCEPT # free output on any interface to any ip for any service # (equal to -P ACCEPT) iptables -A OUTPUT -j ACCEPT # permit answers on already established connections # and permit new connections related to established ones (eg active-ftp) iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT #Gamespy&NWN #iptables -A INPUT -p tcp -m tcp -m multiport --ports 5120:5129 -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 6667 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 28910 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29900 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29901 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29920 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p udp -m udp -m multiport --ports 5120:5129 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 6500 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 27900 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 27901 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 29910 -j ACCEPT # Log everything else: What's Windows' latest exploitable vulnerability? iptables -A INPUT -j LOG --log-prefix "FIREWALL:INPUT" # set a sane policy: everything not accepted > /dev/null iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP iptables -A INPUT -p icmp --icmp-type echo-request -j DROP # be verbose on dynamic ip-addresses (not needed in case of static IP) echo 2 > /proc/sys/net/ipv4/ip_dynaddr # disable ExplicitCongestionNotification - too many routers are still # ignorant echo 0 > /proc/sys/net/ipv4/tcp_ecn #ping death echo 1 > /proc/sys/net/ipv4/icmp_echo_ignore_all # If you are frequently accessing ftp-servers or enjoy chatting you might # notice certain delays because some implementations of these daemons have # the feature of querying an identd on your box for your username for # logging. Although there's really no harm in this, having an identd # running is not recommended because some implementations are known to be # vulnerable. # To avoid these delays you could reject the requests with a 'tcp-reset': #iptables -A INPUT -p tcp --dport 113 -j REJECT --reject-with tcp-reset #iptables -A OUTPUT -p tcp --sport 113 -m state --state RELATED -j ACCEPT # To log and drop invalid packets, mostly harmless packets that came in # after netfilter's timeout, sometimes scans: #iptables -I INPUT 1 -p tcp -m state --state INVALID -j LOG --log-prefix \ "FIREWALL:INVALID" #iptables -I INPUT 2 -p tcp -m state --state INVALID -j DROP # End /bin/firewall-start

  Read the article

• Bind9 Debian Not responding

  - by Marc

  Im trying to set up a webserver with Bind9, apache2 on Debian 6. I am trying to learn to do it manualy so I do not have any control panels or anything just the command line. I have a domain name lets call it www.example.com I want a virtual host setup so that I can have multiple websites with different names on my server. I have ns1.example.com and ns2.example.com registered at my servers IP (123.456.789.12). Below is my Bind9 named.conf.options options { directory "/var/cache/bind"; // If there is a firewall between you and nameservers you want // to talk to, you may need to fix the firewall to allow multiple // ports to talk. See http://www.kb.cert.org/vuls/id/800113 // If your ISP provided one or more IP addresses for stable // nameservers, you probably want to use them as forwarders. // Uncomment the following block, and insert the addresses replacing // the all-0's placeholder. // forwarders { // 0.0.0.0; // }; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; This is the default I'm not sure if i was supposed to edit it. I didn't. Here is my named.conf.default-zones: // prime the server with knowledge of the root servers zone "." { type hint; file "/etc/bind/db.root"; }; // be authoritative for the localhost forward and reverse zones, and for // broadcast zones as per RFC 1912 zone "localhost" { type master; file "/etc/bind/db.local"; }; zone "127.in-addr.arpa" { type master; file "/etc/bind/db.127"; }; zone "0.in-addr.arpa" { type master; file "/etc/bind/db.0"; }; zone "255.in-addr.arpa" { type master; file "/etc/bind/db.255"; }; zone "example.com.com" { type master; file "etc/bind/example.com.db"; }; named.conf.local Is an empty file with a comment saying to do local configuration here. example.com.db looks like this: ; BIND data file for mywebsite.com ; $ORIGIN example.com. $TTL 604800 @ IN SOA ns1.example.com. [email protected]. ( 2009120101 ; Serial 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; IN NS ns1.example.com. IN NS ns2.example.com. IN MX 10 mail.example.com. localhost IN A 127.0.0.1 example.com. IN A 123.456.789.12 ns1 IN A 123.456.789.12 ns2 IN A 123.456.789.12 www IN A 123.456.789.12 ftp IN A 123.456.789.12 mail IN A 123.456.789.12 boards IN CNAME www These are all settings I've found from various tutorials. Now when i go to intodns I get: You should already know that your NS records at your nameservers are missing, so here it is again: ns1.example.com ns2.example.com Can someone help me? I'm not sure what Im doing wrong.

  Read the article

• iptables 1.4 and passive FTP on custom port

  - by Cracky

  after the upgrade from debian squeeze to wheezy I've got a problem with passive FTP connection. I could narrow it to be iptables related, as I could connect via FTP w/o problems after adding my IP to the iptables ACCEPT rule. Before the upgrade I was able just to do modprobe nf_conntract_ftp ports=21332 and adding iptables -A THRU -p tcp --dport 21332 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT now..it doesn't help anymore. The INPUT rule is being triggered as I can see in the counter, but the directory listing is the last thing it does. Setting up a passive-port range is the last thing I want to do, I dislike open ports. I also tried the trick with helper mod by adding following rule before the actual rule for 21332 iptables -A THRU -p tcp -i eth0 --dport 21332 -m state --state NEW -m helper --helper ftp-21332 -j ACCEPT but it doesn't help and is even not being triggered according to counter. The rule in the next line (w/o helper) is being triggered.. here some info: # iptables --version iptables v1.4.14 # lsmod |grep nf_ nf_nat_ftp 12460 0 nf_nat 18242 1 nf_nat_ftp nf_conntrack_ftp 12605 1 nf_nat_ftp nf_conntrack_ipv4 14078 32 nf_nat nf_defrag_ipv4 12483 1 nf_conntrack_ipv4 nf_conntrack 52720 7 xt_state,nf_conntrack_ipv4,xt_conntrack,nf_conntrack_ftp,nf_nat,nf_nat_ftp,xt_helper # uname -a Linux loki 3.2.0-4-amd64 #1 SMP Debian 3.2.46-1 x86_64 GNU/Linux # iptables-save # Generated by iptables-save v1.4.14 on Sun Jun 30 03:54:28 2013 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :BLACKLIST - [0:0] :LOGDROP - [0:0] :SPAM - [0:0] :THRU - [0:0] :WEB - [0:0] :fail2ban-dovecot-pop3imap - [0:0] :fail2ban-pureftpd - [0:0] :fail2ban-ssh - [0:0] -A INPUT -p tcp -m multiport --dports 110,995,143,993 -j fail2ban-dovecot-pop3imap -A INPUT -p tcp -m multiport --dports 21,21332 -j fail2ban-pureftpd -A INPUT -p tcp -m multiport --dports 22 -j fail2ban-ssh -A INPUT -p tcp -m multiport --dports 110,995,143,993 -j fail2ban-dovecot-pop3imap -A INPUT -i lo -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG NONE -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,SYN FIN,SYN -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags SYN,RST SYN,RST -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,RST FIN,RST -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,ACK FIN -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags ACK,URG URG -j DROP -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT -A INPUT -j BLACKLIST -A INPUT -j THRU -A INPUT -j LOGDROP -A OUTPUT -j ACCEPT -A OUTPUT -s 93.223.38.223/32 -j ACCEPT -A BLACKLIST -s 38.113.165.0/24 -j LOGDROP -A BLACKLIST -s 202.177.216.0/24 -j LOGDROP -A BLACKLIST -s 130.117.190.0/24 -j LOGDROP -A BLACKLIST -s 117.79.92.0/24 -j LOGDROP -A BLACKLIST -s 72.47.228.0/24 -j LOGDROP -A BLACKLIST -s 195.200.70.0/24 -j LOGDROP -A BLACKLIST -s 195.200.71.0/24 -j LOGDROP -A LOGDROP -m limit --limit 5/sec -j LOG --log-prefix drop_packet_ --log-level 7 -A LOGDROP -p tcp -m tcp --dport 25 -m limit --limit 2/sec -j LOG --log-prefix spam_blacklist --log-level 7 -A LOGDROP -p tcp -m tcp --dport 80 -m limit --limit 2/sec -j LOG --log-prefix web_blacklist --log-level 7 -A LOGDROP -p tcp -m tcp --dport 22 -m limit --limit 2/sec -j LOG --log-prefix ssh_blacklist --log-level 7 -A LOGDROP -j REJECT --reject-with icmp-host-prohibited -A THRU -p icmp -m limit --limit 1/sec -m icmp --icmp-type 8 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 25 -j ACCEPT -A THRU -i eth0 -p udp -m udp --dport 53 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 80 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 110 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 143 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 465 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 585 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 993 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 995 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 2008 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 10011 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 21332 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 30033 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A fail2ban-dovecot-pop3imap -j RETURN -A fail2ban-dovecot-pop3imap -j RETURN -A fail2ban-pureftpd -j RETURN -A fail2ban-pureftpd -j RETURN -A fail2ban-ssh -j RETURN -A fail2ban-ssh -j RETURN COMMIT # Completed on Sun Jun 30 03:54:28 2013 So, as I said, I have no problems with connecting when adding my IP to go through..but that's not a solution as noone except me can connect anymore~ If someone got an idea what the problem is, please help me! Thanks Cracky

  Read the article

• How do I connect my Windows XP laptop to the internet?

  - by rubysiddhi

  Hello fellow super users, The Past I have a Acer Travelmate 2300 laptop running Windows XP. 6 months ago I moved into a new apartment and got a new internet connection set up. After getting an internet connection installed in my apartment I reinstalled Windows XP and at the same time wiped my drive clean losing all the original Acer software and drivers. Once XP was reinstalled I had to find all the drivers again to get the Travelmate laptop connected to the internet. So, using my Vista laptop which was connected fine, I went to the Acer Travelmate Series drivers download page to download the necessary drivers. I transferred them to my Acer XP machine and installed them the best I could (there were no easy instructions so I just had to find all the executables and run them). I eventually got connected to the internet but not exactly in the way I had hoped for. The Present To be connected to the internet I need to have an Ethernet cord connecting my computer (via the Ethernet port) to my router. This is a problem since it defeats the purpose of having a Wireless LAN card in my Acer laptop. One of the programs I downloaded from the Acer Travelmate Series page was the Acer Wireless LAN Configuration Utility. This program allows me to see the current network I am connected to and all the available networks I could potentially connect to. It reminds me of XP's Wireless Network Connection window/utility where you can see all available wireless networks, refresh the network list and connect to one of the networks. I should mention that my ISP set up a security enabled wireless network with WPA. This network requires a network key if you want to connect to it. I guess my Vista computer has the network key entered into it already. The problem is that I do not know what the network key is. Now obviously you would say just contact my ISP to get the key. And I will but there is just one extra weird issue. I am able to connect to another unsecured wireless network in the Wireless Network Connection window/utility. I can be on it as long as my Ethernet cable is plugged in. So this is not really wireless is it? And this indicates that even if I do get that network key password from my ISP, I will only solve one of the two problems I have. I will only solve being able to get online as long as I am connected to my router via the Ethernet cable. The Main Questions So how do I enable my acer IPN2220 Wireless LAN Card so that I can use my Acer laptop from anywhere with in my apartment? Or should I first get the network key from my ISP to access my security enabled wireless network? And then deal with getting the acer IPN2220 Wireless LAN Card working? Hard & Learned VS Easy & Stupid Of course contacting the ISP would be easier. Have em just come in here and do there thing. The problem with that is that they do not speak English (yeah, im in Poland) and it'd be a hell of a time trying to understand what they are doing (uncomfortable looking over their shoulder). Also, I want to learn how to do this task myself so that I can fix the problem if it ever happens again. You know, be more self sufficient. I look forward to helpful replies. Thanks, Xaviour

  Read the article

• How do bots access directories on a server that are not DocumentRoot of public IP address? How do I stop them?

  - by tmsimont

  I have a local network set up with apache2 and "named" running on OpenSuse 13.1 Linux. I used the "named" service to use my computer as a domain server. I set up my router to point to ask my computer for domain lookups, so I have a chance to have it rewrite a bunch of domains on my network to its own local IP, 192.168.0.111 This works great. I use virtual host configuration to allow various domains and subdomains (re-routed to the same IP via named) to pull up different directories in my computer. For example: <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias fmb.wa.net DocumentRoot /home/work/wa.net/fmb </VirtualHost> <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias postrecord.wa.net DocumentRoot /home/work/wa.net/postrecord </VirtualHost> <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias cvalley.wa.net DocumentRoot /home/work/wa.net/cvalley_local </VirtualHost> This makes it possible for me to hit cvalley.wa.net from any device in my network and get the site that lives in /home/work/wa.net/cvalley_local I decided to forward port 80 to this computer, so I could share a few development sites with coworkers. I can't control which site they see with the same named service, because they'd have to use my computer as their domain name server... So I added a line like this: <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias MY.IP.XXX.XX DocumentRoot /home/work/wa.net/cvalley </VirtualHost> Where "MY.IP.XXX.XX" is my public IP address. This works as expected, when you hit my IP address from a public network you see the site that lives in /home/work/wa.net/cvalley. The point of confusion that I have is that there are public IP addresses in my logs in other sites. I would have expected it to be impossible to access other sites in my network, unless the public user somehow figured out what I'm calling my ServerAliases, and is mimicing my domain set up... How can public traffic be hitting my other local sites? How can I recreate this kind of access? Here are some examples of public IP's hitting my VirtualHost sites: 162.253.66.76 - - [15/Aug/2014:19:20:47 -0600] "GET /xmlrpc.php HTTP/1.0" 404 1004 "-" "-" 162.253.66.74 - - [16/Aug/2014:10:50:28 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 185.4.227.194 - - [16/Aug/2014:11:16:45 -0600] "GET http://24x7-allrequestsallowed.com/?PHPSESSID=1rysxtj500143WQMVT%5E_NAZ%5BQ HTTP/1.1" 200 262 "-" "-" 101.226.254.138 - - [16/Aug/2014:13:32:14 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 162.253.66.74 - - [16/Aug/2014:14:26:19 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 212.129.2.119 - - [16/Aug/2014:16:00:51 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 91.240.163.111 - - [16/Aug/2014:18:34:32 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 162.253.66.74 - - [16/Aug/2014:19:02:53 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 122.226.223.69 - - [17/Aug/2014:05:53:09 -0600] "GET http://www.k2proxy.com//hello.html HTTP/1.1" 404 1006 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; WOW64; Trident/6.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; .NET4.0C; .NET4.0E)" ::1 - - [17/Aug/2014:10:19:26 -0600] "OPTIONS * HTTP/1.0" 200 - "-" "Apache/2.4.6 (Linux/SUSE) OpenSSL/1.0.1e PHP/5.4.20 (internal dummy connection)" 162.209.65.196 - - [17/Aug/2014:15:31:53 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 111.206.199.163 - - [18/Aug/2014:11:12:56 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 37.187.180.168 - - [18/Aug/2014:15:40:00 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 62.210.38.226 - - [18/Aug/2014:18:35:16 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" Is there anything that I can do to reliably deny public access by default, but allow it only in one VirtualHost?

  Read the article

• WPF CommandParameter is NULL first time CanExecute is called

  - by Jonas Follesø

  I have run into an issue with WPF and Commands that are bound to a Button inside the DataTemplate of an ItemsControl. The scenario is quite straight forward. The ItemsControl is bound to a list of objects, and I want to be able to remove each object in the list by clicking a Button. The Button executes a Command, and the Command takes care of the deletion. The CommandParameter is bound to the Object I want to delete. That way I know what the user clicked. A user should only be able to delete their "own" objects - so I need to do some checks in the "CanExecute" call of the Command to verify that the user has the right permissions. The problem is that the parameter passed to CanExecute is NULL the first time it's called - so I can't run the logic to enable/disable the command. However, if I make it allways enabled, and then click the button to execute the command, the CommandParameter is passed in correctly. So that means that the binding against the CommandParameter is working. The XAML for the ItemsControl and the DataTemplate looks like this: <ItemsControl x:Name="commentsList" ItemsSource="{Binding Path=SharedDataItemPM.Comments}" Width="Auto" Height="Auto"> <ItemsControl.ItemTemplate> <DataTemplate> <StackPanel Orientation="Horizontal"> <Button Content="Delete" FontSize="10" Command="{Binding Path=DataContext.DeleteCommentCommand, ElementName=commentsList}" CommandParameter="{Binding}" /> </StackPanel> </DataTemplate> </ItemsControl.ItemTemplate> </ItemsControl> So as you can see I have a list of Comments objects. I want the CommandParameter of the DeleteCommentCommand to be bound to the Command object. So I guess my question is: have anyone experienced this problem before? CanExecute gets called on my Command, but the parameter is always NULL the first time - why is that? Update: I was able to narrow the problem down a little. I added an empty Debug ValueConverter so that I could output a message when the CommandParameter is data bound. Turns out the problem is that the CanExecute method is executed before the CommandParameter is bound to the button. I have tried to set the CommandParameter before the Command (like suggested) - but it still doesn't work. Any tips on how to control it. Update2: Is there any way to detect when the binding is "done", so that I can force re-evaluation of the command? Also - is it a problem that I have multiple Buttons (one for each item in the ItemsControl) that bind to the same instance of a Command-object? Update3: I have uploaded a reproduction of the bug to my SkyDrive: http://cid-1a08c11c407c0d8e.skydrive.live.com/self.aspx/Code%20samples/CommandParameterBinding.zip

  Read the article

• java 7 upgrade and hibernate annotation processor error

  - by Bill Turner

  I am getting the following warning, which seems to be triggering a subsequent warning and an error. I have been googling like mad, though have not found anything that makes it clear what it is I should do to resolve this. This issue occurs when I execute an Ant build. I am trying to migrate our project to Java 7. I have changed all the source='1.6' and target="1.6" to 1.7. I did find this related article: Forward compatible Java 6 annotation processor and SupportedSourceVersion It seems to indicate that I should build the Hibernate annotation processor jar myself, compiling it with with 1.7. It does not seem I should be required to do so. The latest version of the class in question (in hibernate-validator-annotation-processor-5.0.1.Final.jar) has been compiled with 1.6. Since the code in said class refers to SourceVersion.latestSupported(), and the 1.6 of that returns only RELEASE_6, there does not seem to be a generally available solution. Here is the warning: [javac] warning: Supported source version 'RELEASE_6' from annotation processor 'org.hibernate.validator.ap.ConstraintValidationProcessor' less than -source '1.7' And, here are the subsequent warnings/error. [javac] warning: No processor claimed any of these annotations: javax.persistence.PersistenceContext,javax.persistence.Column,org.codehaus.jackson.annotate.JsonIgnore,javax.persistence.Id,org.springframework.context.annotation.DependsOn,com.trgr.cobalt.infrastructure.datasource.Bucketed,org.codehaus.jackson.map.annotate.JsonDeserialize,javax.persistence.DiscriminatorColumn,com.trgr.cobalt.dataroom.authorization.secure.Secured,org.hibernate.annotations.GenericGenerator,javax.annotation.Resource,com.trgr.cobalt.infrastructure.spring.domain.DomainField,org.codehaus.jackson.annotate.JsonAutoDetect,javax.persistence.DiscriminatorValue,com.trgr.cobalt.dataroom.datasource.config.core.CoreTransactionMandatory,org.springframework.stereotype.Repository,javax.persistence.GeneratedValue,com.trgr.cobalt.dataroom.datasource.config.core.CoreTransactional,org.hibernate.annotations.Cascade,javax.persistence.Table,javax.persistence.Enumerated,org.hibernate.annotations.FilterDef,javax.persistence.OneToOne,com.trgr.cobalt.dataroom.datasource.config.core.CoreEntity,org.springframework.transaction.annotation.Transactional,com.trgr.cobalt.infrastructure.util.enums.EnumConversion,org.springframework.context.annotation.Configuration,com.trgr.cobalt.infrastructure.spring.domain.UpdatedFields,com.trgr.cobalt.infrastructure.spring.documentation.SampleValue,org.springframework.context.annotation.Bean,org.codehaus.jackson.annotate.JsonProperty,javax.persistence.Basic,org.codehaus.jackson.map.annotate.JsonSerialize,com.trgr.cobalt.infrastructure.spring.validation.Required,com.trgr.cobalt.dataroom.datasource.config.core.CoreTransactionNever,org.springframework.context.annotation.Profile,com.trgr.cobalt.infrastructure.spring.stereotype.Persistor,javax.persistence.Transient,com.trgr.cobalt.infrastructure.spring.validation.NotNull,javax.validation.constraints.Size,javax.persistence.Entity,javax.persistence.PrimaryKeyJoinColumn,org.hibernate.annotations.BatchSize,org.springframework.stereotype.Service,org.springframework.beans.factory.annotation.Value,javax.persistence.Inheritance [javac] error: warnings found and -Werror specified TIA!

  Read the article

• Computer science undergraduate project ideas

  - by Mehrdad Afshari

  Hopefully, I'm going to finish my undergraduate studies next semester and I'm thinking about the topic of my final project. And yes, I've read the questions with duplicate title. I'm asking this from a bit different viewpoint, so it's not an exact dupe. I've spent at least half of my life coding stuff in different languages and frameworks so I'm not looking at this project as a way to learn much about coding and preparing for real world apps or such. I've done lots of those already. But since I have to do it to complete my degree, I felt I should spend my time doing something useful instead of throwing the whole thing out. I'm planning to make it an open source project or a hosted Web app (depending on the type) if I can make a high quality thing out of it, so I decided to ask StackOverflow what could make a useful project. Situation I've plenty of freedom about the topic. They also require 30-40 pages of text describing the project. I have the following points in mind (the more satisfied, the better): Something useful for software development Something that benefits the community Having academic value is great Shouldn't take more than a month of development (I know I'm lazy). Shouldn't be related to advanced theoretical stuff (soft computing, fuzzy logic, neural networks, ...). I've been a business-oriented software developer. It should be software oriented. While I love hacking microcontrollers and other fun embedded electronic things, I'm not really good at soldering and things like that. I'm leaning toward a Web application (think StackOverflow, PasteBin, NerdDinner, things like those). Technology It's probably going to be done in .NET (C#, F#) and Windows platform. If I really like the project (cool low level hacking), I might actually slip to C/C++. But really, C# is what I'm efficient at. Ideas Programming language, parsing and compiler related stuff: Designing a domain specific programming language and compiler Templating language compiled to C# or IL Database tools and related code generation stuff Web related technologies: ASP.NET MVC View engine doing something cool (don't know what exactly...) Specific-purpose, small, fast ASP.NET-based Web framework Applications: Visual Studio plugin to integrate with Bazaar (it's too much work, I think). ASP.NET based, jQuery-powered issue tracker (and possibly, project lifecycle management as a whole - poor man's TFS) Others: Something related to GPGPU Looking forward for great ideas! Unfortunately, I can't help on a currently existing project. I need to start my own to prevent further problems (as it's an undergrad project, nevertheless).

  Read the article

• Python Memory leak - Solved, but still puzzled

  - by disappearedng

  Dear everyone, I have successfully debugged my own memory leak problems. However, I have noticed some very strange occurence. for fid, fv in freqDic.iteritems(): outf.write(fid+"\t") #ID for i, term in enumerate(domain): #Vector tfidf = self.tf(term, fv) * self.idf( term, docFreqDic) if i == len(domain) - 1: outf.write("%f\n" % tfidf) else: outf.write("%f\t" % tfidf) outf.flush() print "Memory increased by", int(self.memory_mon.usage()) - startMemory outf.close() def tf(self, term, freqVector): total = freqVector[TOTAL] if total == 0: return 0 if term not in freqVector: ## When you don't have these lines memory leaks occurs return 0 ## return float(freqVector[term]) / freqVector[TOTAL] def idf(self, term, docFrequencyPerTerm): if term not in docFrequencyPerTerm: return 0 return math.log( float(docFrequencyPerTerm[TOTAL])/docFrequencyPerTerm[term]) Basically let me describe my problem: 1) I am doing tfidf calculations 2) I traced that the source of memory leaks is coming from defaultdict. 3) I am using the memory_mon from http://stackoverflow.com/questions/276052/how-to-get-current-cpu-and-ram-usage-in-python 4) The reason for my memory leaks is as follows: a) in self.tf, if the lines: if term not in freqVector: return 0 are not added that will cause the memory leak. (I verified this myself using memory_mon and noticed a sharp increase in memory that kept on increasing) The solution to my problem was 1) since fv is a defaultdict, any reference to it that are not found in fv will create an entry. Over a very large domain, this will cause memory leaks. I decided to use dict instead of default dict and the memory problem did go away. My only puzzle is: since fv is created in "for fid, fv in freqDic.iteritems():" shouldn't fv be destroyed at the end of every for loop? I tried putting gc.collect() at the end of the for loop but gc was not able to collect everything (returns 0). Yes, the hypothesis is right, but the memory should stay fairly consistent with ever for loop if for loops do destroy all temp variables. This is what it looks like with that two line in self.tf: Memory increased by 12 Memory increased by 948 Memory increased by 28 Memory increased by 36 Memory increased by 36 Memory increased by 32 Memory increased by 28 Memory increased by 32 Memory increased by 32 Memory increased by 32 Memory increased by 40 Memory increased by 32 Memory increased by 32 Memory increased by 28 and without the the two line: Memory increased by 1652 Memory increased by 3576 Memory increased by 4220 Memory increased by 5760 Memory increased by 7296 Memory increased by 8840 Memory increased by 10456 Memory increased by 12824 Memory increased by 13460 Memory increased by 15000 Memory increased by 17448 Memory increased by 18084 Memory increased by 19628 Memory increased by 22080 Memory increased by 22708 Memory increased by 24248 Memory increased by 26704 Memory increased by 27332 Memory increased by 28864 Memory increased by 30404 Memory increased by 32856 Memory increased by 33552 Memory increased by 35024 Memory increased by 36564 Memory increased by 39016 Memory increased by 39924 Memory increased by 42104 Memory increased by 42724 Memory increased by 44268 Memory increased by 46720 Memory increased by 47352 Memory increased by 48952 Memory increased by 50428 Memory increased by 51964 Memory increased by 53508 Memory increased by 55960 Memory increased by 56584 Memory increased by 58404 Memory increased by 59668 Memory increased by 61208 Memory increased by 62744 Memory increased by 64400 I look forward to your answer

  Read the article

• Integrating POP3 client functionality into a C# application?

  - by flesh

  I have a web application that requires a server based component to periodically access POP3 email boxes and retrieve emails. The service then needs to process the emails which will involve: Validating the email against some business rules (does it contain a valid reference in the subject line, which user sent the mail, etc.) Analysing and saving any attachments to disk Take the email body and attachment details and create a new item in the database Or update an existing item where the reference matches the incoming email subject line What is the best way to approach this? I really don't want to have to write a POP3 client from scratch, but I need to be able to customize the processing of emails. Ideally I would be able to plug in some component that does the access and retrieval for me, returning arrays of attachments, body text, subject line, etc. ready for my processing... [ UPDATE: Reviews ] OK, so I have spent a fair amount of time looking into (mainly free) .NET POP3 libraries so I thought I'd provide a short review of some of those mentioned below and a few others: Pop3.net - free - works OK, very basic in terms of functionality provided. This is pretty much just the POP3 commands and some base64 encoding, but it's very straight forward - probably a good introduction Pop3 Wizard - commercial / some open source code - couldn't get this to build, missing DLLs, I wouldn't bother with this C#Mail - free - works well, comes with Mime parser and SMTP client, however the comments are in Japanese (not a big deal) and it didn't work with SSL 'out of the box' - I had to change the SslStream constructor after which it worked no problem OpenPOP - free - hasn't been updated for about 5 years so it's current state is .NET 1.0, doesn't support SSL but that was no problem to resolve - I just replaced the existing stream with an SslStream and it worked. Comes with Mime parser. Of the free libraries, I'd go for C#Mail or OpenPOP. I looked at a few commercial libraries: Chillkat, Rebex, RemObjects, JMail.net. Based on features, price and impression of the company I would probably go for Rebex and may in the future if my requirements change or I run into production issues with either of C#Mail or OpenPOP. In case anyone's needs it, this is the replacement SslStream constructor that I used to enable SSL with C#Mail and OpenPOP: SslStream stream = new SslStream(clientSocket.GetStream(), false, delegate(object sender, X509Certificate cert, X509Chain chain, SslPolicyErrors errors) { return true; });

  Read the article

• Run MySQL INSERT Query multiple times (insert values into multiple tables)

  - by Derek

  Hi, basically, I have 3 tables; users and projects (which is a many-to-many relationship), then I have 'usersprojects' to allow the one-to-many formation. When a user adds a project, I need the project information stored and then the 'userid' and 'projectid' stored in the usersprojects table. It sounds like its really straight forward but I'm having problems with the syntax I think!? As it stands, I have this as my INSERT queries (values going into 2 different tables): $project_id = $_POST['project_id']; $projectname = $_POST['projectname']; $projectdeadline = $_POST['projectdeadline']; $projectdetails = $_POST['projectdetails']; $user_id = $_POST['user_id']; $sql = "INSERT INTO projects (projectid, projectname, projectdeadline, projectdetails) VALUES ('{$projectid}','{$projectname}','{$projectdeadline}','{$projectdetails}')"; $sql = "INSERT INTO usersprojects (userid, projectid) VALUES ('{$userid}','{$projectid}')"; None of the information is being stored in the projects table, but the user ID is being stored in the usersprojects table (but not project ID!?)... I did have it working where the project information is stored correctly with a project ID, before I added this bit: $sql = "INSERT INTO usersprojects (userid, projectid) VALUES ('{$userid}','{$projectid}')"; But before the code above was put in, obviously no info is being stored in usersprojects table. The source code that links the script: <form id="addform" name="addform" method="POST" action="addproject-run.php"> <label>Project Name:</label> <input name="projectname" size="40" id="projectname" value="<?php if (isset($_POST['projectname'])); ?>"/><br /> <input name="user_id" input type="hidden" size="40" id="user_id" value="<?php echo $_SESSION['SESS_USERID']; ?>"/> <label>Project Deadline:</label> <input name="projectdeadline" size="40" id="projectdeadline" value="In the format of 'YYYY-MM-DD'<?php if (isset($_POST['projectdeadline'])); ?>"/><br /> <label>Project Details:</label> <textarea rows="5" cols="20" name="projectdetails" id="projectdetails"><?php if (isset($_POST['projectdetails'])); ?></textarea> <br /> <br /> <input value="Create Project" class="addbtn" type="submit" /> </form></div> So I think I'm right in saying I have the syntax for the SQL statement to be run an insert query of values into 2 tables? Any help is much appreciated! Thanks.

  Read the article

• Log4r : logger inheritance, yaml configuration, alternatives ?

  - by devlearn

  Hello, I'm pretty new to ruby environments and I was looking for a nice logging framework to use it my ruby and rails applications. In my previous experiences I have successfully used log4j and log4p (the perl port) and was expecting the same level of usability (and maturity) with log4r. However I must say that there are a number of things that are not clear at all in the log4r framework. 1 Logger Inheritance The logger inheritance does not seem to be managed at all ! If I declare a logger named 'myapp' and then try to get a logger name 'myapp::engine', the lookup will end with a NameError. I would expect that the framework returns the root logger according to the naming scheme and to use the 'myapp' logger. Q1 : Of course I can work around this and manage the names by myself with a lookup method, however is there a cleaner way to do this without any extra coding ? 2 YAML configuration Second thing that confuses me is the yaml configuration. On the log4r site there are literally no information about this system, the doc links forward to missing pages, so all the info I can find about is contained in the examples directory of the gem. I was pretty confused with the fact that the yaml configuration must contain the pre_config section, and that I need to define my own levels. If I remove the pre_config secion, or replace all the “custom” levels by the standard ones ( debug, info, warn, fatal ) , the example will throw the following error : log4r/yamlconfigurator.rb:68:in `decode_yaml': Log level must be in 0..7 (ArgumentError) So there seems to be no way of using a simple file where we only declare the loggers and appenders for the framework. Q2 : I realy think that I missed something and that must be a way of providing a simple yaml conf file. Do you have any examples of such an usage ? 3 Variables substitution in XML file Q3 : The Yaml configuration system seems to provide such a feature however I was unable to find a similar feature with XML files. Any ideas ? 4 Alternatives ? I must say that I'm very disappointed by the feature level and the maturity of log4r compared to the log4j and other log4j ports. I run into this framework with a solid background of logging APIs in other languages and find myself working around in all kinds just to make 'basic things' running in a “real world application”. By that I mean a complex application composed of several gems, console/scripting apps, and a rails web front end where the configuration must be mutualized and where we make intensive usage of namespaces and inheritance. I've run several searches in order to find something more suitable or mature, but did not find anything similar. Q4 : Do you guys know any (serious) alternatives to log4r framework that could be used in a enterprise class app ? Thanks reading all of this ! I'd really appreciate any pointers, Kind Regards,

  Read the article

• delta-dictionary/dictionary with revision awareness in python?

  - by shabbychef

  I am looking to create a dictionary with 'roll-back' capabilities in python. The dictionary would start with a revision number of 0, and the revision would be bumped up only by explicit method call. I do not need to delete keys, only add and update key,value pairs, and then roll back. I will never need to 'roll forward', that is, when rolling the dictionary back, all the newer revisions can be discarded, and I can start re-reving up again. thus I want behaviour like: >>> rr = rev_dictionary() >>> rr.rev 0 >>> rr["a"] = 17 >>> rr[('b',23)] = 'foo' >>> rr["a"] 17 >>> rr.rev 0 >>> rr.roll_rev() >>> rr.rev 1 >>> rr["a"] 17 >>> rr["a"] = 0 >>> rr["a"] 0 >>> rr[('b',23)] 'foo' >>> rr.roll_to(0) >>> rr.rev 0 >>> rr["a"] 17 >>> rr.roll_to(1) Exception ... Just to be clear, the state associated with a revision is the state of the dictionary just prior to the roll_rev() method call. thus if I can alter the value associated with a key several times 'within' a revision, and only have the last one remembered. I would like a fairly memory-efficient implementation of this: the memory usage should be proportional to the deltas. Thus simply having a list of copies of the dictionary will not scale for my problem. One should assume the keys are in the tens of thousands, and the revisions are in the hundreds of thousands. We can assume the values are immutable, but need not be numeric. For the case where the values are e.g. integers, there is a fairly straightforward implementation (have a list of dictionaries of the numerical delta from revision to revision). I am not sure how to turn this into the general form. Maybe bootstrap the integer version and add on an array of values? all help appreciated.

  Read the article

• jQuery unbinding click event when maximum number of children are displayed

  - by RyanP13

  I have a personal details form that alows you to enter a certain number of dependants which is determined by the JSP application. The first dependant is visible and the user has the option to add dependants up to the maximum number. All other dependants are hidden by default and are displayed when a user clicks the 'Add another dependant button'. When the maximum number of dependants has been reached the button is greyed out and a message is generated via jQuery and displayed to tell the user exactly this. The issue i am having is when the maximum number of dependants has been reached the message is displayed but then the user can click the button to add more dependants and the message keeps on generating. I thought unbinding the click event would sort this but it seems to still be able to generate a second message. Here is the function i wrote to generate the message: // Dependant message function function maxDependMsg(msgElement) { // number of children can change per product, needs to be dynamic // count number of dependants in HTML var $dependLength = $("div.dependant").length; // add class maxAdd to grey out Button // create maximum dependants message and display, will not be created if JS turned off $(msgElement) .addClass("maxAdd") .after($('<p>') .addClass("maxMsg") .append("The selected web policy does not offer cover for more than " + $dependLength + " children, please contact our customer advisers if you wish discuss alternative policies available.")); } There is a hyperlink with a click event attached like so: $("a.add").click(function(){ // Show the next hidden table on clicking add child button $(this).closest('form').find('div.dependant:hidden:first').show(); // Get the number of hidden tables var $hiddenChildren = $('div.dependant:hidden').length; if ($hiddenChildren == 0) { // save visible state of system message $.cookies.set('cpqbMaxDependantMsg', 'visible'); // show system message that you can't add anymore dependants than what is on page maxDependMsg("a.add"); $(this).unbind("click"); } // set a cookie for the visible state of all child tables $('div.dependant').each(function(){ var $childCount = $(this).index('div.dependant'); if ($(this).is(':visible')) { $.cookies.set('cpqbTableStatus' + $childCount, 'visible'); } else { $.cookies.set('cpqbTableStatus' + $childCount, 'hidden'); } }); return false; }); All of the cookies code is for state saving when users are going back and forward through the process.

  Read the article

• tapestry 4 session expired

  - by cometta

  is below caused by user session expired? if yes, how to exend session on tapestry 4 ? or any other way to solve this problem? Unable to process client request: Unable to forward to local resource '/app?service=page&page=Home&id=692': java.lang.NullPointerException: Property 'webRequest' of <OuterProxy for tapestry.globals.RequestGlobals(org.apache.tapestry.services.RequestGlobals)> is null. Apr 22, 2010 5:14:43 PM org.apache.catalina.core.ApplicationContext log SEVERE: app: ServletException javax.servlet.ServletException: java.lang.NullPointerException: Property 'webRequest' of <OuterProxy for tapestry.globals.RequestGlobals(org.apache.tapestry.services.RequestGlobals)> is null. at org.apache.tapestry.services.impl.WebRequestServicerPipelineBridge.service(WebRequestServicerPipelineBridge.java:65) at $ServletRequestServicer_128043b52ea.service($ServletRequestServicer_128043b52ea.java) at org.apache.tapestry.request.DecodedRequestInjector.service(DecodedRequestInjector.java:55) at $ServletRequestServicerFilter_128043b52e6.service($ServletRequestServicerFilter_128043b52e6.java) at $ServletRequestServicer_128043b52ec.service($ServletRequestServicer_128043b52ec.java) at org.apache.tapestry.multipart.MultipartDecoderFilter.service(MultipartDecoderFilter.java:52) at $ServletRequestServicerFilter_128043b52e4.service($ServletRequestServicerFilter_128043b52e4.java) at $ServletRequestServicer_128043b52ec.service($ServletRequestServicer_128043b52ec.java) at org.apache.tapestry.services.impl.SetupRequestEncoding.service(SetupRequestEncoding.java:53) at $ServletRequestServicerFilter_128043b52e8.service($ServletRequestServicerFilter_128043b52e8.java) at $ServletRequestServicer_128043b52ec.service($ServletRequestServicer_128043b52ec.java) at $ServletRequestServicer_128043b52de.service($ServletRequestServicer_128043b52de.java) at org.apache.tapestry.ApplicationServlet.doService(ApplicationServlet.java:126) at org.apache.tapestry.ApplicationServlet.doPost(ApplicationServlet.java:171) at javax.servlet.http.HttpServlet.service(HttpServlet.java:637) at javax.servlet.http.HttpServlet.service(HttpServlet.java:717) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:290) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.springframework.security.util.FilterChainProxy$VirtualFilterChain.doFilter(FilterChainProxy.java:378) at org.springframework.security.intercept.web.FilterSecurityInterceptor.invoke(FilterSecurityInterceptor.java:109) at org.springframework.security.intercept.web.FilterSecurityInterceptor.doFilter(FilterSecurityInterceptor.java:83) at org.springframework.security.util.FilterChainProxy$VirtualFilterChain.doFilter(FilterChainProxy.java:390) at org.springframework.security.ui.SessionFixationProtectionFilter.doFilterHttp(SessionFixationProtectionFilter.java:67) at org.springframework.security.ui.SpringSecurityFilter.doFilter(SpringSecurityFilter.java:53) at org.springframework.security.util.FilterChainProxy$VirtualFilterChain.doFilter(FilterChainProxy.java:390) at org.springframework.security.ui.ntlm.NtlmProcessingFilter.doFilterHttp(NtlmProcessingFilter.java:358) at org.springframework.security.ui.SpringSecurityFilter.doFilter(SpringSecurityFilter.java:53) at org.springframework.security.util.FilterChainProxy$VirtualFilterChain.doFilter(FilterChainProxy.java:390) at org.springframework.security.ui.ExceptionTranslationFilter.doFilterHttp(ExceptionTranslationFilter.java:101) at org.springframework.security.ui.SpringSecurityFilter.doFilter(SpringSecurityFilter.java:53) at org.springframework.security.util.FilterChainProxy$VirtualFilterChain.doFilter(FilterChainProxy.java:390) at org.springframework.security.context.HttpSessionContextIntegrationFilter.doFilterHttp(HttpSessionContextIntegrationFilter.java:235) at org.springframework.security.ui.SpringSecurityFilter.doFilter(SpringSecurityFilter.java:53) at org.springframework.security.util.FilterChainProxy$VirtualFilterChain.doFilter(FilterChainProxy.java:390) at org.springframework.security.concurrent.ConcurrentSessionFilter.doFilterHttp(ConcurrentSessionFilter.java:99) at org.springframework.security.ui.SpringSecurityFilter.doFilter(SpringSecurityFilter.java:53) at org.springframework.security.util.FilterChainProxy$VirtualFilterChain.doFilter(FilterChainProxy.java:390) at org.springframework.security.util.FilterChainProxy.doFilter(FilterChainProxy.java:175) at org.springframework.web.filter.DelegatingFilterProxy.invokeDelegate(DelegatingFilterProxy.java:236) at org.springframework.web.filter.DelegatingFilterProxy.doFilter(DelegatingFilterProxy.java:167) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:233) at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:191) at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:128) at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:102) at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:109) at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:286) at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:845) at org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.process(Http11Protocol.java:583) at org.apache.tomcat.util.net.JIoEndpoint$Worker.run(JIoEndpoint.java:447) at java.lang.Thread.run(Thread.java:619)

  Read the article

• PopulateOnDemand does not work on data bound ASP.Net TreeView

  - by Shay Friedman

  Hi, I have a TreeView that is bound to a XmlDataSource control. I've added some TreeNodeBinding elements to define how I want the XML data to be shown. I have also added PopulateOnDemand=true to these TreeNodeBindings. However, doing so didn't change a thing and the entire XML tree is displayed. Moreover, the TreeNodePopulate event is not fired on node expand as well. Important information: I'm using ASP.NET 4. This is an example that reproduces the problem (very straight forward): <%@ Page Language="C#" AutoEventWireup="true" %> <script type="text/C#" runat="server"> protected void TreeView1_TreeNodePopulate(Object sender, TreeNodeEventArgs e) { // This method is never called... } </script> <html xmlns="http://www.w3.org/1999/xhtml"> <head runat="server"> <title></title> </head> <body> <form id="form1" runat="server"> <div> <asp:TreeView ID="TreeView1" runat="server" DataSourceID="XmlDataSource1" OnTreeNodePopulate="TreeView1_TreeNodePopulate" ExpandDepth="0"> <DataBindings> <asp:TreeNodeBinding DataMember="#" TextField="#" ValueField="#" PopulateOnDemand="true" /> </DataBindings> </asp:TreeView> <asp:XmlDataSource ID="XmlDataSource1" runat="server" DataFile="Sample.xml" /> </div> </form> </body> </html> The Sample.xml can be any xml file you want, it doesn't really matter. I tried to put a breakpoint within the TreeView1_TreeNodePopulate method and it was never hit. I also tried to: Set a TreeNodeBinding for each possible data member with PopulateOnDemand="true". Via code, go through all tree nodes and set their PopulateOnDemand property to true. Nothing worked. The only way the populate-on-demand thing worked was when I added nodes manually to the nodes instead of binding it to a data source. What am I doing wrong?

  Read the article

• std::basic_stringstream<unsigned char> won't compile with MSVC 10

  - by Michael J

  I'm trying to get UTF-8 chars to co-exist with ANSI 8-bit chars. My strategy has been to represent utf-8 chars as unsigned char so that appropriate overloads of functions can be used for the two character types. e.g. namespace MyStuff { typedef uchar utf8_t; typedef std::basic_string<utf8_t> U8string; } void SomeFunc(std::string &s); void SomeFunc(std::wstring &s); void SomeFunc(MyStuff::U8string &s); This all works pretty well until I try to use a stringstream. std::basic_ostringstream<MyStuff::utf8_t> ostr; ostr << 1; MSVC Visual C++ Express V10 won't compile this: c:\program files\microsoft visual studio 10.0\vc\include\xlocmon(213): warning C4273: 'id' : inconsistent dll linkage c:\program files\microsoft visual studio 10.0\vc\include\xlocnum(65) : see previous definition of 'public: static std::locale::id std::numpunct<unsigned char>::id' c:\program files\microsoft visual studio 10.0\vc\include\xlocnum(65) : while compiling class template static data member 'std::locale::id std::numpunct<_Elem>::id' with [ _Elem=Tk::utf8_t ] c:\program files\microsoft visual studio 10.0\vc\include\xlocnum(1149) : see reference to function template instantiation 'const _Facet &std::use_facet<std::numpunct<_Elem>>(const std::locale &)' being compiled with [ _Facet=std::numpunct<Tk::utf8_t>, _Elem=Tk::utf8_t ] c:\program files\microsoft visual studio 10.0\vc\include\xlocnum(1143) : while compiling class template member function 'std::ostreambuf_iterator<_Elem,_Traits> std::num_put<_Elem,_OutIt>:: do_put(_OutIt,std::ios_base &,_Elem,std::_Bool) const' with [ _Elem=Tk::utf8_t, _Traits=std::char_traits<Tk::utf8_t>, _OutIt=std::ostreambuf_iterator<Tk::utf8_t,std::char_traits<Tk::utf8_t>> ] c:\program files\microsoft visual studio 10.0\vc\include\ostream(295) : see reference to class template instantiation 'std::num_put<_Elem,_OutIt>' being compiled with [ _Elem=Tk::utf8_t, _OutIt=std::ostreambuf_iterator<Tk::utf8_t,std::char_traits<Tk::utf8_t>> ] c:\program files\microsoft visual studio 10.0\vc\include\ostream(281) : while compiling class template member function 'std::basic_ostream<_Elem,_Traits> & std::basic_ostream<_Elem,_Traits>::operator <<(int)' with [ _Elem=Tk::utf8_t, _Traits=std::char_traits<Tk::utf8_t> ] c:\program files\microsoft visual studio 10.0\vc\include\sstream(526) : see reference to class template instantiation 'std::basic_ostream<_Elem,_Traits>' being compiled with [ _Elem=Tk::utf8_t, _Traits=std::char_traits<Tk::utf8_t> ] c:\users\michael\dvl\tmp\console\console.cpp(23) : see reference to class template instantiation 'std::basic_ostringstream<_Elem,_Traits,_Alloc>' being compiled with [ _Elem=Tk::utf8_t, _Traits=std::char_traits<Tk::utf8_t>, _Alloc=std::allocator<uchar> ] . c:\program files\microsoft visual studio 10.0\vc\include\xlocmon(213): error C2491: 'std::numpunct<_Elem>::id' : definition of dllimport static data member not allowed with [ _Elem=Tk::utf8_t ] Any ideas? ** Edited 19 June 2012 ** OK, I've gotten closer to understanding this, but not how to solve it. As we all know, static class variables get defined twice: once in the class definition and once outside the class definition which establishes storage space. e.g. // in .h file class CFoo { // ... static int x; }; // in .cpp file int CFoo::x = 42; Now in the VC10 headers we get something like this: template<class _Elem> class numpunct : public locale::facet { // ... _CRTIMP2_PURE static locale::id id; // ... } When the header is included in an application, _CRTIMP2_PURE is defined as __declspec(dllimport), which means that the variable is imported from a dll. Now the header also contains the following template<class _Elem> locale::id numpunct<_Elem>::id; Note the absence of the __declspec(dllimport) qualifier. i.e. The class declaration says that the static linkage of the id variable is in the dll, but for the general case, it gets declared outside the dll. For the known cases, there are specialisations. template locale::id numpunct<char>::id; template locale::id numpunct<wchar_t>::id; These are protected by #ifs so that they are only included when building the DLL. They are excluded otherwise. i.e. the char and wchar_t versions of numpunct ARE inside the dll So we have the class definition saying that id's storage is in the DLL, but that is only true for the char and wchar_t specialisations, meaning that my unsigned char version is doomed. :-( The only way forward that I can think of is to create my own specialisation: basically copying it from the header file and fixing it. This raises many issues. Anybody have a better idea?

  Read the article

< Previous Page | 243 244 245 246 247 248 249 250 251 252 253 254  | Next Page >