Search Results

Search found 2053 results on 83 pages for 'signal'.

Page 25/83 | < Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >

  • Atheros AR928X wireless connection makes neighbourhood machine drop off line

    - by funicorn
    I have an Acer laptop with Atheros AR928X wireless card installed, supported by ath9k driver in the linux kernel. There are other 5 computers sharing wireless connection via a TPLink 150Mbit/s wireless router. At first I found the network is a little bit slower than it's in Windows7, which I accepted as it should be. However a very strange thing is, each time I connected to the router and downloaded stuff for a while, one of the computers running Windows7 in my local network dropped off from the router. And if I run my laptop under Windows7, everything is fine. What's even stranger is although the network becomes slower, only the certain computer drops and totally freezes in connection with the router. I'm not willing to conclude it's due to the unhealthy connection from my laptop to the router, however we have confirmed this for more than one times and there is no problem with the network when I'm running WIndows7. I'm extremely confused about what's going on. As a Linux user running Ubuntu over 5 years, I am awared that wireless driver in Linux is badly notorious of lack of stability and slow speed. But is it so bad that the unhealthy wireless connection can do damage to another computer in the same local network? I do see a lot of "Tx excessive retries" in iwconfig output. But how exactly does this happen ? Thanks for your help. I guess I have to use this answer box to show the outputs $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=47/70 Signal level=-63 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:2 Invalid misc:23 Missed beacon:0 To show what's wrong with the wireless connection, I ran iwconfig again within 3 minutes, during which time I hardly did anything and the network was not much busy than being nearly idle $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9 Invalid misc:28 Missed beacon:0 You can see Tx excessive retires and Invalid misc increase very quickly. $ sudo iwlist wlan0 modu wlan0 unknown modulation information. $ sudo iwlist wlan0 channel wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Current Frequency:2.427 GHz (Channel 4)

    Read the article

  • Retro Ad – 10 MB Hard-Drive for $3398 [Image]

    - by Asian Angel
    This is definitely one hard-drive (and price) that you will not be feeling nostalgic over! View the Full-Size Version of the Ad (Image) The Hard Disk you’ve been waiting for. [via Fail Desk] Why Enabling “Do Not Track” Doesn’t Stop You From Being Tracked HTG Explains: What is the Windows Page File and Should You Disable It? How To Get a Better Wireless Signal and Reduce Wireless Network Interference

    Read the article

  • Redbull Stratos Jump in LEGO [Video]

    - by Jason Fitzpatrick
    Last weekend Felix Baumgartner skydived from the edge of space; it was only a matter of (very brief) time before someone rendered the event in LEGO. [via Neatorama] Why Enabling “Do Not Track” Doesn’t Stop You From Being Tracked HTG Explains: What is the Windows Page File and Should You Disable It? How To Get a Better Wireless Signal and Reduce Wireless Network Interference

    Read the article

  • Why is my system freezing when I switch users

    - by ZeroDivide
    Hello I've recently upgraded from 13.04 to 13.10 64bit. I'm running AMD graphics with the proprietary drivers. I have two user accounts. Mine(administrator) and my girlfriend's(standard) My girlfriend clicks "switch user" from my lock screen and logs in fine. I then try to click "switch user" from her lock screen and everything goes black. Then the monitor blinks on and off with just a single cursor. I have no way to access the terminal, the system is unresponsive and I have to hit the power button. Even ctrl + alt + f4 or ctrl + alt + t doesn't get me a terminal. When I press the power button on my system, it does start printing out the shutdown sequence on the monitor. Here is my .xsession-errors Script for ibus started at run_im. Script for auto started at run_im. Script for default started at run_im. Here is hers: init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd respawning too fast, stopped init: logrotate main process (4726) killed by TERM signal init: upstart-dbus-session-bridge main process (4865) terminated with status 1 init: gnome-settings-daemon main process (4843) terminated with status 1 init: gnome-session main process (4852) terminated with status 1 init: unity-panel-service main process (4863) killed by KILL signal I found some advice in a forum to look for at-spi2-registryd in my system logs. Perhaps it will be useful. executing this: sudo grep -r at-spi2-registryd /var/log/* produces this: /var/log/lightdm/x-1-greeter.log:** (at-spi2-registryd:4384): WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.gnome.SessionManager was not provided by any .service files /var/log/lightdm/x-1-greeter.log:** (at-spi2-registryd:4384): WARNING **: Unable to register client with session manager /var/log/lightdm/x-2-greeter.log.old:** (at-spi2-registryd:7447): WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.gnome.SessionManager was not provided by any .service files /var/log/lightdm/x-2-greeter.log.old:** (at-spi2-registryd:7447): WARNING **: Unable to register client with session manager /var/log/lightdm/x-0-greeter.log:** (at-spi2-registryd:1378): WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.gnome.SessionManager was not provided by any .service files /var/log/lightdm/x-0-greeter.log:** (at-spi2-registryd:1378): WARNING **: Unable to register client with session manager /var/log/lightdm/x-0-greeter.log.old:** (at-spi2-registryd:1357): WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.gnome.SessionManager was not provided by any .service files /var/log/lightdm/x-0-greeter.log.old:** (at-spi2-registryd:1357): WARNING **: Unable to register client with session manager Any ideas what is going on?

    Read the article

  • From the Tips Box: Xbox Output on Two Screens, High Tech Halloween Props, and Old Flash Drives as Password Reset Disks

    - by Jason Fitzpatrick
    Once a week we round up some great reader tips and share them with everyone, this week we’re looking at outputting your Xbox 360 to two screens, spooky high-tech Halloween props, and recycling old flash drives as password reset disks. HTG Explains: What is the Windows Page File and Should You Disable It? How To Get a Better Wireless Signal and Reduce Wireless Network Interference How To Troubleshoot Internet Connection Problems

    Read the article

  • Quickly, code and ui are not communicating well, at all

    - by Alex
    I have been following the http://developer.ubuntu.com/resources/tutorials/all/diy-media-player-with-pygtk/ tutorial, i followed everything in it to the letter. i even set the signal of the tool button "openbutton" to on_openbutton_clicked. i run the code, click the button, nothing happens. i cant seem to get the button to do anything. any help will be super amazing!! http://pastebin.com/7Tq99Ytg pastebin to the .py file.

    Read the article

  • New Best-in-Class Solutions in Supply Chain Planning - Part 1

    Hear Nadeem Syed, Oracle Group Vice President, Advanced Planning Products discusst Oracle's recently announced best-in-class Supply Chain Planning solutions: Advanced Planning Command Center, Demand Signal Repository, Spare Parts Planning and Manufacturing Operations Center. Gain an understanding of the capabilities of these ground-breaking planning solutions and what types of enterprises can benefit from them.

    Read the article

  • Network manager broadband modem BUG

    - by Souheil Hmida
    just upgraded to ubuntu 12.10 from 12.04 using wvdial to connect to the internet (network manager doesn't detect my modem Huawei E367 ), though the new network manager detected my modem and asked me the enter the PIN, it doesn't connect, it shows my provider (Orange TN) and the signal (2 bars) but dosn't connect and I can't clic on the name of my broadband (ORANGE TN) . Just hoping that there will be a bug-fix for it or any other solution so I can go back to using the network manger :)

    Read the article

  • How do I detect when my system wakes up from suspend via DBus or similar in a python app?

    - by con-f-use
    In a background Python script I need to detect, when the system just woke up from suspend. What is a good way that does not rely on a root script but rather on python modules such as DBus? I'm new to dbus so I could really use some example code. From what I read it's related to org.freedesktop.UPower /org/freedesktop/UPower org.freedesktop.UPower.Resuming Can anyone help me out with some code that connects the resuming signal to callback?

    Read the article

  • Slow wireless on Dell XPS 14 ultrabook

    - by GaryBishop
    I've got Ubuntu 12.04 running on this Dell XPS 14 Ultrabook (L421X). Everything is working but my wireless transfer rates are low. I'm getting about 1MB/s download speed on the ultrabook vs 15MB/s on the E6500. If I move into the room with the access point the speed climbs to 15MB/s so I'm guessing it is a signal strength issue but wavemon shows comparable signals to those seen by the E6500. Are there any settings I can tweak in hopes of making it faster?

    Read the article

  • How to Enable or Disable the Startup Sound in Windows 8

    - by Taylor Gibb
    We have all been in that awkward situation where you sit down in a meeting room only to have your Windows laptop play the Startup sound. Here’s how to disable it or even enable it if you so choose. HTG Explains: What is the Windows Page File and Should You Disable It? How To Get a Better Wireless Signal and Reduce Wireless Network Interference How To Troubleshoot Internet Connection Problems

    Read the article

  • Week in Geek: Windows 8 Security Flaw – Passwords Stored in Plain Text When Using Picture or PIN Login

    - by Asian Angel
    This week’s edition of WIG is filled with news link coverage on topics such as new malware seeks to lock Skype users out of their PCs, Dell will stick to Windows 7 after Windows 8 debut, Mozilla Thunderbird users now get 25 GB of cloud storage for free, and more. HTG Explains: What is the Windows Page File and Should You Disable It? How To Get a Better Wireless Signal and Reduce Wireless Network Interference How To Troubleshoot Internet Connection Problems

    Read the article

  • How to Clear Metro Application Notifications at Log Off in Windows 8

    - by Taylor Gibb
    Sometimes in Windows 8 you may find your application notifications getting stuck from time to time, the fix to this problem is to clear the notification cache at log off, here’s how. Why Enabling “Do Not Track” Doesn’t Stop You From Being Tracked HTG Explains: What is the Windows Page File and Should You Disable It? How To Get a Better Wireless Signal and Reduce Wireless Network Interference

    Read the article

  • How best to look up objects by label?

    - by dsollen
    I am writing the server backed by a pre-written API. I'm going to get a number of strings representing ports, signals, paths, etc etc etc. I need to look up the object associated with a given label, these objects are all in memory (no sql magic to do this for me). My question is, how best do I associate a given unique label with the mutable object it represents? I have enough objects that looking through every signal or every port to find the one that matches is possible, but may be slightly too slow. To be honest the direct 'look at every object' method is probably good enough for so small a body of objects and anything else is premature optimization, but I still am curious what the proper solution would be if I thought my signals were going to grow a bit larger. As I see it there are two options available. First would be to to create a 'store' that is a simple map between object and label. I could have it so that every time I call addObject the object is automatically saved into a hashmap or the like. This works, but relies on my properly adding and deleting each object so the map doesn't grow indefinitely. The biggest issue to me is that this involves having some hidden static map in my ModelObject class that just feels...wrong somehow. The other option is to have some method that can interpret the labels. All of these labels are derived from the underlying objects. So I can look at the signal label, for instance, and say "these 20 characters are the port" to figure out what port I need. This would allow me to quickly figure out what I need. However, if the label method is changed the translateLabelToObject method needs to be updated as well or everything breaks. Which solution is cleaner, or possibly a cleaner solution than either of above? For the record I'm working with sufficient number of variables to make direct comparison a little slow, but not enough to be concerned about memory overhead, written in java. All objects that have labels I need to look up extend the same parent class.

    Read the article

  • Basic modelling of radar

    - by Hawk66
    I'm currently researching how to model/simulate radar for my naval simulation. Since the emphasis is on modelling ASW or submarines in general, I need only a basic radar model - at least for the beginning. So, does anybody know a resource for such a simple model? The model should take signal strength of the sensor, the size of the target and the terrain (height/ground clutter) into account. Thanks.

    Read the article

  • How do I get a TP-LINK WN723N wireless USB adapter working?

    - by Bottie
    I am having trouble using a TP-LINK WN723N wireless USB adapter on my computer which is running Ubuntu 12.04. When I plug the adapter in, the computer automatically picks up a signal from my wireless router but only connects to the internet for a short amount of time before losing the connection. I have searched for additional drivers and have tried running the .exe installation file on the WINE drive with no such luck... Am very new to Ubuntu would love some help! Thanks :-)

    Read the article

  • How to Enable Click To Play Plugins in Google Chrome

    - by Taylor Gibb
    Have you ever opened a webpage only to have all sorts of multimedia on the page just start playing? Chrome has a hidden setting that was designed to prevent situations just like that. Read on to find out how to enable it. HTG Explains: What is the Windows Page File and Should You Disable It? How To Get a Better Wireless Signal and Reduce Wireless Network Interference How To Troubleshoot Internet Connection Problems

    Read the article

  • I have Ubuntu 12.04 installed on my pc and the pc hangs and does not restart more (translated)

    - by adail
    Translated from google My pc is an intel atom + Yes, it came with windows 7, formatted and installed Ubuntu 12.04, but the pc is unstable, it will not turn off properly and alone, appearing msg that there is no image signal, what to do? Meu pc é um Sim+ intel aton, veio com o windows 7, formatei e instalei o ubunto 12.04, mas o pc está instavel, ele não liga corretamente e desliga sozinho, aparecendo a msg que não ha sinal de imagem, o que fazer?

    Read the article

  • How to configure an Ubuntu 12.04 virtual server and VMWare ESXi5 the way VMWare would be able to shut it down properly?

    - by Ivan
    I run an Ubuntu 12.04 server as a virtual machine on a VMWare ESXi 5 server. I've configured VMWare to shut the quest machines down the sane way (with an ACPI (if I understand it righ) shutdown signal so that guest OSes would do it). And this works with other VMs (running Windows 7 Professional and openSuSE) but doesn't work with the Ubuntu server - VMWare still offers just to power them off when I ask it to stop the guest. Any ideas how to fix this?

    Read the article

  • Wifi problems with Ubuntu 13.10

    - by Sparrowhawk4
    I should probably say straight off that I am brand new to Ubuntu. I installed 13.10 alongside Windows 7 a couple of days ago and I've managed to clear up all the little problems, apart from with the wifi. My internet is fine using an ethernet cable. I can connect to the wifi, and it tells me that the signal is good, but for the vast majority of the time I can't load anything, and system monitor tells me that I am sending and receiving nothing. The problem is somewhere in Ubuntu. It works fine on Windows 7, my Android phone and all of my flatmates laptops. I know I'm not the only one with this problem, but the fixes I've seen either don't work or I don't understand them enough to carry them out. Help? EDIT: from lspci command as requested 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 00:1f.6 Signal processing controller: Intel Corporation 82801I (ICH9 Family) Thermal Subsystem (rev 03) 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvA Wireless LAN Controller (rev 10) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)

    Read the article

  • What's New in Oracle Supply Chain Management: Key highlights of R12.1 and new solutions (PART 2 of 2

    The latest EBS 12.1 release provides significant new capabilities in supply chain management that companies can deploy immediately to drive rapid ROI.  In addition, new solutions such as Advanced Planning Command Center, Spare Parts Planning, Demand Signal Repository and Manufacturing Operations Center enable companies to achieve operational excellence, while reducing costs and improving margins. This webcast will discuss the latest release, highlighting new capabilities and how companies can benefit from them.

    Read the article

  • What's New in Oracle Supply Chain Management: Key highlights of R12.1 and new solutions (PART 1 of 2

    The latest EBS 12.1 release provides significant new capabilities in supply chain management that companies can deploy immediately to drive rapid ROI.  In addition, new solutions such as Advanced Planning Command Center, Spare Parts Planning, Demand Signal Repository and Manufacturing Operations Center enable companies to achieve operational excellence, while reducing costs and improving margins. This webcast will discuss the latest release, highlighting new capabilities and how companies can benefit from them.

    Read the article

  • Dual VGA monitors with Quadro FX 580?

    - by dentrasi
    I have a machine with a Quadro FX 580 card (DVI and two Displayport). Attached to it are two 19" Acer screens, which are both (annoyingly) VGA. The first one works perfectly, with a DVI-VGA adaptor. The second one doesn't work. It's got a VGA cable, which goes into a VGA-DVI converted, which then goes into a DVI-Displayport converter. Initally, I was getting 'Cable Unplugged' on the screen, and it couldn't be seen by Windows or the nVidia control panel. After swapping the VGA-DVI adaptor (which works perfectly on another machine), Windows can now see the monitor. The nVidia panel sees the model and native resolution, but I get a constant 'No Signal' error. Switching to the other Displayport makes no difference. I suspect that the card is seeing a DVI connection plugged into it (nVididaCP shows the monitor as having a DVI connection), and it only sending out a digital signal because of this. Does anyone know of a solution (other than trying to get a Displayport-VGA adaptor), or of a way to force the card to see it as VGA? Thanks, ~Dentrasi

    Read the article

  • Are HDMI to VGA Adapters Really Device-Specific?

    - by allquixotic
    There are a lot of devices on the market right now (especially mobile devices) with a Micro-HDMI or Mini-HDMI port and no VGA or D-Sub output. Most manufacturers of said devices sell a cable that looks something like this: I have yet to find a cable like this that claims to work on a wide array of devices. In general, these cables claim to work with one specific device only. The way these cables work, I think, is that analog VGA signals are sent from the HDMI port on the device. This should work for devices that have special hardware on the motherboard/GPU capable of driving this. Is it the case that these cables have to be custom designed for each device? Or, is it rather that any device which possesses this special "signaling of analog VGA over the HDMI port" can be made to work with a cable that is physically compatible (i.e. the HDMI end plugs into the device and the VGA end accepts a VGA monitor cable)? Note that I am not looking for a product recommendation, just a conceptual clarification on what exactly these devices are doing. Also, a few remarks: The cables like the one depicted here are not digital to analog converters. I know about these: they are expensive, and they are the ONLY solution if your device only outputs a digital signal and is incapable of driving analog VGA over the HDMI port. The cables like the one depicted here are not straight crossover cables from VGA to HDMI, either. The crossover cables are designed to send a digital HDMI signal over the VGA port's wires; that is, the wire protocol is HDMI (digital) but the physical pinout is the same as VGA, even though nothing analog is happening. Once again, this is not the behavior that, I believe, the devices which I'm talking about in this question are doing. The cabling and devices that this question is about transmit the analog VGA data over the HDMI port (the HDMI port is in the device outputting the data, and the VGA side is the monitor/projector).

    Read the article

< Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >