Search Results

Search found 7211 results on 289 pages for 'enable if'.

Page 252/289 | < Previous Page | 248 249 250 251 252 253 254 255 256 257 258 259  | Next Page >

• Dual Boot Oracle Solaris 11/11 and Linux (Ubuntu 11.10/grub2)

  - by HartmutStreppel

  After having worked with Open Solaris on my laptop first, then with an upgrade to Oracle Solaris 11 Express, I finally did a fresh install of Oracle Solaris 11/11, when it became available. I am not a big fan of upgrades as I know that I am not the perfect administrator and my system gets spoiled with unclean configurations, outdated packages and wrong settings that cannot be reversed. So I prefer to start from scratch. Especially with Oracle Solaris 11 I wanted to have a system just like a customer would have it in production. The installation was smooth - more or less, if I had only read the documentation a bit better in advance. For a number of reasons I prefer a dual boot system. The most important one is, that especially with mobile devices you often run into network problems. And you have a hard time figuring out where the problem is: in your laptop hardware, in the OS you are running, or really within the network. If you have an alternate OS to boot, you can exclude the OS and your hardware. This makes you feel better. The second OS should be a Linux variant - and for some not so obvious reason I decided to go with the latest Ubuntu release (11.10). It replaced a very old Open Suse installation that had not been booted for a while. I knew that it was probably best to install Ubuntu first and then Oracle Solaris 11, as this would put the right boot information for Oracle Solaris  into the MBR and onto the root partition. But then, how to enable dual boot with the 2 OSes. Searching the web one mainly finds information about dual boot of: Linux and Linux Linux and Windows I do not want to explain which wrong configurations I worked through, but I prefer to explain the final setup, which is extremely simple, and I am wondering why this is not covered as the easiest solution for most dual boot setups. I use chainloader from and to both OS'es, with the only disadvantage that I have to confirm two grub menus each time I want to boot the "other" OS. Still there were some hurdles to jump over: Ubuntu did not like getting its boot blocks being placed on the partition instead of the disk; I must admit that I do not fully understand why. But using the --force option you could get that done Ubuntu needs an active partition; that was easy to achieve grub2 uses a different numbering scheme for the partitions. That is in the docs, if you read them. BTW: The usual disclaimer is valid. There is  no guarantee that what I describe works or works well. Please back up your data carefully before trying any of this. So, Oracle Solaris 11 is installed on the first partition and Ubuntu on the third. With Ubtuntu things initially were a bit more complicated, as I did not know how to boot it. And the live CD did not offer the capability to boot the on-disk image (at least I did not find it). So I booted the live CD, mounted the Ubuntu installation at /mnt and wrote the boot blocks into the partition. This is something that does not seem to be recommended, at least grub-install refrained from doing what I intended. After a bit more research I was bold enough to use the --force option and wrote the boot blocks to /dev/sda3 using grub-install --boot-directory=/mnt/boot --force --no-floppy /dev/sda3 So, I now had a system with the Solaris boot loader in the MBR, Solaris specific boot blocks on the Solaris root partition and Ubuntu specific boot blocks in the Ubuntu partition. I just had to chain them together and I was done. Oracle Solaris 11: I have added the following lines to /rpool/boot/grub/menu.lst (be aware of the /rpool!!!!) title Ubuntu 11.10root (hd0,2)makeactivechainloader +1boot The Ubuntu root file system sits on the third partition (/dev/sda3). Ubuntu: I have added the following lines to /etc/grub.d/40_custom: menuentry "Solaris 11/11" {      set root=(hd0,1)      chainloader +1} Two things need to be mentioned: a) grub2 starts numbering partitions with 1; so my /dev/sda1 is partition 1. b) Oracle Solaris boots without the partition being made active (btw: the command to make a partition active with grub2 is "parttool (hd0,1) boot+", which currently does not work for me). As debugging grub is a bit complicated, I used the grub CLI to perform some tests and also used a tool, that I found on sourceforge.net that was able to prepare a list of all boot loaders on all partitions. This told me that the basic setup was correct. Unfortunately I lost it in the live CD environment. I hope this is helpful for some of the readers.Hartmut

  Read the article

• Change the Default Font Size in Word

  - by Matthew Guay

  Are you frustrated by always having to change the font size before you create a document it Word?  Here’s how you can end that frustration and set your favorite default font size for once and for all! Microsoft changed the default font font to 11 point Calibri in Word 2007 after years of 12 point Times New Roman being the default.  Although it can be easily overlooked, there are ways in Word to change the default settings to anything you want.  Whether you want to change your default to 12 point Calibri or to 48 point Comic Sans…here’s how to change your default font settings in Word 2007 and 2010. Changing Default Fonts in Word To change the default font settings, click the small box with an arrow in the right left corner of the Font section of the Home tab in the Ribbon.   In the Font dialog box, choose the default font settings you want.  Notice in the Font box it says “+Body”; this means that the font will be chosen by the document style you choose, and you are only selecting the default font style and size.  So, if your style uses Calibri, then your font will be Calibri at the size and style you chose.  If you’d prefer to choose a specific font to be the default, just select one from the drop-down box and this selection will override the font selection in your document style. Here we left all the default settings, except we selected 12 point font in the Latin text box (this is your standard body text; users of Asian languages such as Chinese may see a box for Asian languages).  When you’ve made your selections, click the “Set as Default” button in the bottom left corner of the dialog. You will be asked to confirm that you want these settings to be made default.  In Word 2010, you will be given the option to set these settings for this document only or for all documents.  Click the bullet beside “All documents based on the Normal.dotm template?”, and then click Ok. In Word 2007, simply click Ok to save these settings as default. Now, whenever you open Word or create a new document, your default font settings should be set exactly to what you want.  And simply repeat these steps to change your default font settings again if you want. Editing your default template file Another way to change your default font settings is to edit your Normal.dotm file.  This file is what Word uses to create new documents; it basically copies the formatting in this document each time you make a new document. To edit your Normal.dotm file, enter the following in the address bar in Explorer or in the Run prompt: %appdata%\Microsoft\Templates This will open your Office Templates folder.  Right-click on the Normal.dotm file, and click Open to edit it.  Note: Do not double-click on the file, as this will only create a new document based on Normal.dotm and any edits you make will not be saved in this file.   Now, change any font settings as you normally would.  Remember: anything you change or enter in this document will appear in any new document you create using Word. If you want to revert to your default settings, simply delete your Normal.dotm file.  Word will recreate it with the standard default settings the next time you open Word. Please Note: Changing your default font size will not change the font size in existing documents, so these will still show the settings you used when these documents were created.  Also, some addins can affect your Normal.dotm template.  If Word does not seem to remember your font settings, try disabling Word addins to see if this helps. Conclusion Sometimes it’s the small things that can be the most frustrating.  Getting your default font settings the way you want is a great way to take away a frustration and make you more productive. And here’s a quick question: Do you prefer the new default 11 point Calibri, or do you prefer 12 point Times New Roman or some other combination?  Sound off in the comments, and let the world know your favorite font settings. Similar Articles Productive Geek Tips Change the Default Font in Excel 2007Add Emphasis to Paragraphs with Drop Caps in Word 2007Keep Websites From Using Tiny Fonts in SafariMake Word 2007 Always Save in Word 2003 FormatStupid Geek Tricks: Enable More Fonts for the Windows Command Prompt TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Spyware Blaster v4.3 Yes, it’s Patch Tuesday Generate Stunning Tag Clouds With Tagxedo Install, Remove and HIDE Fonts in Windows 7 Need Help with Your Home Network? Awesome Lyrics Finder for Winamp & Windows Media Player

  Read the article

• ASP.NET Web API - Screencast series Part 4: Paging and Querying

  - by Jon Galloway

  We're continuing a six part series on ASP.NET Web API that accompanies the getting started screencast series. This is an introductory screencast series that walks through from File / New Project to some more advanced scenarios like Custom Validation and Authorization. The screencast videos are all short (3-5 minutes) and the sample code for the series is both available for download and browsable online. I did the screencasts, but the samples were written by the ASP.NET Web API team. In Part 1 we looked at what ASP.NET Web API is, why you'd care, did the File / New Project thing, and did some basic HTTP testing using browser F12 developer tools. In Part 2 we started to build up a sample that returns data from a repository in JSON format via GET methods. In Part 3, we modified data on the server using DELETE and POST methods. In Part 4, we'll extend on our simple querying methods form Part 2, adding in support for paging and querying. This part shows two approaches to querying data (paging really just being a specific querying case) - you can do it yourself using parameters passed in via querystring (as well as headers, other route parameters, cookies, etc.). You're welcome to do that if you'd like. What I think is more interesting here is that Web API actions that return IQueryable automatically support OData query syntax, making it really easy to support some common query use cases like paging and filtering. A few important things to note: This is just support for OData query syntax - you're not getting back data in OData format. The screencast demonstrates this by showing the GET methods are continuing to return the same JSON they did previously. So you don't have to "buy in" to the whole OData thing, you're just able to use the query syntax if you'd like. This isn't full OData query support - full OData query syntax includes a lot of operations and features - but it is a pretty good subset: filter, orderby, skip, and top. All you have to do to enable this OData query syntax is return an IQueryable rather than an IEnumerable. Often, that could be as simple as using the AsQueryable() extension method on your IEnumerable. Query composition support lets you layer queries intelligently. If, for instance, you had an action that showed products by category using a query in your repository, you could also support paging on top of that. The result is an expression tree that's evaluated on-demand and includes both the Web API query and the underlying query. So with all those bullet points and big words, you'd think this would be hard to hook up. Nope, all I did was change the return type from IEnumerable<Comment> to IQueryable<Comment> and convert the Get() method's IEnumerable result using the .AsQueryable() extension method. public IQueryable<Comment> GetComments() { return repository.Get().AsQueryable(); } You still need to build up the query to provide the $top and $skip on the client, but you'd need to do that regardless. Here's how that looks: $(function () { //--------------------------------------------------------- // Using Queryable to page //--------------------------------------------------------- $("#getCommentsQueryable").click(function () { viewModel.comments([]); var pageSize = $('#pageSize').val(); var pageIndex = $('#pageIndex').val(); var url = "/api/comments?$top=" + pageSize + '&$skip=' + (pageIndex * pageSize); $.getJSON(url, function (data) { // Update the Knockout model (and thus the UI) with the comments received back // from the Web API call. viewModel.comments(data); }); return false; }); }); And the neat thing is that - without any modification to our server-side code - we can modify the above jQuery call to request the comments be sorted by author: $(function () { //--------------------------------------------------------- // Using Queryable to page //--------------------------------------------------------- $("#getCommentsQueryable").click(function () { viewModel.comments([]); var pageSize = $('#pageSize').val(); var pageIndex = $('#pageIndex').val(); var url = "/api/comments?$top=" + pageSize + '&$skip=' + (pageIndex * pageSize) + '&$orderby=Author'; $.getJSON(url, function (data) { // Update the Knockout model (and thus the UI) with the comments received back // from the Web API call. viewModel.comments(data); }); return false; }); }); So if you want to make use of OData query syntax, you can. If you don't like it, you're free to hook up your filtering and paging however you think is best. Neat. In Part 5, we'll add on support for Data Annotation based validation using an Action Filter.

  Read the article

• HDFC Bank's Journey to Oracle Private Database Cloud

  - by Nilesh Agrawal

  One of the key takeaways from a recent post by Sushil Kumar is the importance of business initiative that drives the transformational journey from legacy IT to enterprise private cloud. The journey that leads to a agile, self-service and efficient infrastructure with reduced complexity and enables IT to deliver services more closely aligned with business requirements. Nilanjay Bhattacharjee, AVP, IT of HDFC Bank presented a real-world case study based on one such initiative in his Oracle OpenWorld session titled "HDFC BANK Journey into Oracle Database Cloud with EM 12c DBaaS". The case study highlighted in this session is from HDFC Bank’s Lending Business Segment, which comprises roughly 50% of Bank’s top line. Bank’s Lending Business is always under pressure to launch “New Schemes” to compete and stay ahead in this segment and IT has to keep up with this challenging business requirement. Lending related applications are highly dynamic and go through constant changes and every single and minor change in each related application is required to be thoroughly UAT tested certified before they are certified for production rollout. This leads to a constant pressure in IT for rapid provisioning of UAT databases on an ongoing basis to enable faster time to market. Nilanjay joined Sushil Kumar, VP, Product Strategy, Oracle, during the Enterprise Manager general session at Oracle OpenWorld 2012. Let's watch what Nilanjay had to say about their recent Database cloud deployment. “Agility” in launching new business schemes became the key business driver for private database cloud adoption in the Bank. Nilanjay spent an hour discussing it during his session. Let's look at why Database-as-a-Service(DBaaS) model was need of the hour in this case  - Average 3 days to provision UAT Database for Loan Management Application Silo’ed UAT environment with Average 30% utilization Compliance requirement consume UAT testing resources DBA activities leads to $$ paid to SI for provisioning databases manually Overhead in managing configuration drift between production and test environments Rollout impact/delay on new business initiatives The private database cloud implementation progressed through 4 fundamental phases - Standardization, Consolidation, Automation, Optimization of UAT infrastructure. Project scoping was carried out and end users and stakeholders were engaged early on right from planning phase and including all phases of implementation. Standardization and Consolidation phase involved multiple iterations of planning to first standardize on infrastructure, db versions, patch levels, configuration, IT processes etc and with database level consolidation project onto Exadata platform. It was also decided to have existing AIX UAT DB landscape covered and EM 12c DBaaS solution being platform agnostic supported this model well. Automation and Optimization phase provided the necessary Agility, Self-Service and efficiency and this was made possible via EM 12c DBaaS. EM 12c DBaaS Self-Service/SSA Portal was setup with required zones, quotas, service templates, charge plan defined. There were 2 zones implemented - Exadata zone  primarily for UAT and benchmark testing for databases running on Exadata platform and second zone was for AIX setup to cover other databases those running on AIX. Metering and Chargeback/Showback capabilities provided business and IT the framework for cloud optimization and also visibility into cloud usage. More details on UAT cloud implementation, related building blocks and EM 12c DBaaS solution are covered in Nilanjay's OpenWorld session here. Some of the key Benefits achieved from UAT cloud initiative are - New business initiatives can be easily launched due to rapid provisioning of UAT Databases [ ~3 hours ] Drastically cut down $$ on SI for DBA Activities due to Self-Service Effective usage of infrastructure leading to  better ROI Empowering  consumers to provision database using Self-Service Control on project schedule with DB end date aligned to project plan submitted during provisioning Databases provisioned through Self-Service are monitored in EM and auto configured for Alerts and KPI Regulatory requirement of database does not impact existing project in queue This table below shows typical list of activities and tasks involved when a end user requests for a UAT database. EM 12c DBaaS solution helped reduce UAT database provisioning time from roughly 3 days down to 3 hours and this timing also includes provisioning time for database with production scale data (ranging from 250 G to 2 TB of data) - And it's not just about time to provision,  this initiative has enabled an agile, efficient and transparent UAT environment where end users are empowered with real control of cloud resources and IT's role is shifted as enabler of strategic services instead of being administrator of all user requests. The strong collaboration between IT and business community right from planning to implementation to go-live has played the key role in achieving this common goal of enterprise private cloud. Finally, real cloud is here and this cloud is accompanied with rain (business benefits) as well ! For more information, please go to Oracle Enterprise Manager  web page or  follow us at :  Twitter | Facebook | YouTube | Linkedin | Newsletter

  Read the article

• SQL SERVER – Planned and Unplanned Availablity Group Failovers – Notes from the Field #031

  - by Pinal Dave

  [Note from Pinal]: This is a new episode of Notes from the Fields series. AlwaysOn is a very complex subject and not everyone knows many things about this. The matter of the fact is there is very little information available on this subject online and not everyone knows everything about this. This is why when a very common question related to AlwaysOn comes, people get confused. In this episode of the Notes from the Field series database expert John Sterrett (Group Principal at Linchpin People) explains a very common issue DBAs and Developer faces in their career and is related to Planned and Unplanned Availablity Group Failovers. Linchpin People are database coaches and wellness experts for a data driven world. Read the experience of John in his own words. Whenever a disaster occurs it will be a stressful scenario regardless of how small or big the disaster is. This gets multiplied when it is your first time working with newer technology or the first time you are going through a disaster without a proper run book. Today, were going to help you establish a run book for creating a planned failover with availability groups. To make today’s session simple were going to have two instances of SQL Server 2012 included in an availability group and walk through the steps of doing an unplanned failover.  We will focus on using the user interface and T-SQL to complete the failovers. We are going to use a two replica Availability Group where each replica is in another location. Therefore, we will be covering Asynchronous (non automatic failover) the following is a breakdown of our availability group utilized today. Seeing the following screen might be scary the first time you come across an unplanned failover.  It looks like our test database used in this Availability Group is not functional and it currently isn’t. The database status is not synchronizing which makes sense because the primary replica went down so it couldn’t synchronize. With that said, we can still failover and make it functional while we troubleshoot why we lost our primary replica. To start we are going to right click on the availability group that needs to be restarted and select failover. This will bring up the following wizard, which will walk you through several steps needed to complete the failover using the graphical user interface provided with SQL Server Management Studio (SSMS). You are going to see warning messages simply because we are in Asynchronous commit mode and can not guarantee ‘no data loss’ when we do failover. Just incase you missed it; you get another screen warning you about potential data loss because we are in Asynchronous mode. Next we get to connect to the specific replica we want to become the primary replica after the failover occurs. In our case, we only have two replicas so this is trivial. In order to failover, it’s required to connect to the replica that will become primary.  The following screen shows that the connection has been made successfully. Next, you will see the final summary screen. Once again, this reminds you that the failover action will cause data loss as were using Asynchronous commit mode due to the distance between instances used for disaster recovery. Finally, once the failover is completed you will see the following screen. If you followed along this long you might be wondering what T-SQL scripts are generated for clicking through all the sections of the wizard. If you have used Database Mirroring in the past you might be surprised.  It’s not too different, which makes sense because the data is being replicated via SQL Server endpoints just like the good old database mirroring. Now were going to take a look at how to do a failover with just T-SQL. First, were going to need to open a new query window and run our query in SQLCMD mode. Just incase you haven’t used SQLCMD mode before we will show you how to enable it below. Now you can run the following statement. Notice, we connect to the replica we want to become primary after failover and specify to force failover to allow data loss. We can use the following script to failback over when our primary instance comes back online. -- YOU MUST EXECUTE THE FOLLOWING SCRIPT IN SQLCMD MODE. :Connect SQL2012PROD1 ALTER AVAILABILITY GROUP [AGSQL2] FORCE_FAILOVER_ALLOW_DATA_LOSS; GO Are your servers running at optimal speed or are you facing any SQL Server Performance Problems? If you want to get started with the help of experts read more over here: Fix Your SQL Server. Reference: Pinal Dave (http://blog.sqlauthority.com)Filed under: Notes from the Field, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL

  Read the article

• Login failed for user 'sa' because the account is currently locked out. The system administrator can

  - by cabhilash

  Login failed for user 'sa' because the account is currently locked out. The system administrator can unlock it. (Microsoft SQL Server, Error: 18486) SQL server has local password policies. If policy is enabled which locks down the account after X number of failed attempts then the account is automatically locked down.This error with 'sa' account is very common. sa is default administartor login available with SQL server. So there are chances that an ousider has tried to bruteforce your system. (This can cause even if a legitimate tries to access the account with wrong password.Sometimes a user would have changed the password without informing others. So the other users would try to lo) You can unlock the account with the following options (use another admin account or connect via windows authentication) Alter account & unlock ALTER LOGIN sa WITH PASSWORD='password' UNLOCK Use another account Almost everyone is aware of the sa account. This can be the potential security risk. Even if you provide strong password hackers can lock the account by providing the wrong password. ( You can provide extra security by installing firewall or changing the default port but these measures are not always practical). As a best practice you can disable the sa account and use another account with same privileges.ALTER LOGIN sa DISABLE You can edit the lock-ot options using gpedit.msc( in command prompt type gpedit.msc and press enter). Navigate to Account Lokout policy as shown in the figure The Following options are available Account lockout threshold This security setting determines the number of failed logon attempts that causes a user account to be locked out. A locked-out account cannot be used until it is reset by an administrator or until the lockout duration for the account has expired. You can set a value between 0 and 999 failed logon attempts. If you set the value to 0, the account will never be locked out. Failed password attempts against workstations or member servers that have been locked using either CTRL+ALT+DELETE or password-protected screen savers count as failed logon attempts. Account lockout duration This security setting determines the number of minutes a locked-out account remains locked out before automatically becoming unlocked. The available range is from 0 minutes through 99,999 minutes. If you set the account lockout duration to 0, the account will be locked out until an administrator explicitly unlocks it. If an account lockout threshold is defined, the account lockout duration must be greater than or equal to the reset time. Default: None, because this policy setting only has meaning when an Account lockout threshold is specified. Reset account lockout counter after This security setting determines the number of minutes that must elapse after a failed logon attempt before the failed logon attempt counter is reset to 0 bad logon attempts. The available range is 1 minute to 99,999 minutes. If an account lockout threshold is defined, this reset time must be less than or equal to the Account lockout duration. Default: None, because this policy setting only has meaning when an Account lockout threshold is specified.When creating SQL user you can set CHECK_POLICY=on which will enforce the windows password policy on the account. The following policies will be applied Define the Enforce password history policy setting so that several previous passwords are remembered. With this policy setting, users cannot use the same password when their password expires.  Define the Maximum password age policy setting so that passwords expire as often as necessary for your environment, typically, every 30 to 90 days. With this policy setting, if an attacker cracks a password, the attacker only has access to the network until the password expires.  Define the Minimum password age policy setting so that passwords cannot be changed until they are more than a certain number of days old. This policy setting works in combination with the Enforce password historypolicy setting. If a minimum password age is defined, users cannot repeatedly change their passwords to get around the Enforce password history policy setting and then use their original password. Users must wait the specified number of days to change their passwords.  Define a Minimum password length policy setting so that passwords must consist of at least a specified number of characters. Long passwords--seven or more characters--are usually stronger than short ones. With this policy setting, users cannot use blank passwords, and they have to create passwords that are a certain number of characters long.  Enable the Password must meet complexity requirements policy setting. This policy setting checks all new passwords to ensure that they meet basic strong password requirements.  Password must meet the following complexity requirement, when they are changed or created: Not contain the user's entire Account Name or entire Full Name. The Account Name and Full Name are parsed for delimiters: commas, periods, dashes or hyphens, underscores, spaces, pound signs, and tabs. If any of these delimiters are found, the Account Name or Full Name are split and all sections are verified not to be included in the password. There is no check for any character or any three characters in succession. Contain characters from three of the following five categories:  English uppercase characters (A through Z) English lowercase characters (a through z) Base 10 digits (0 through 9) Non-alphabetic characters (for example, !, $, #, %) A catch-all category of any Unicode character that does not fall under the previous four categories. This fifth category can be regionally specific.

  Read the article

• SQL SERVER – The Story of a Lesser Known Startup Parameter in SQL Server – Guest Post by Balmukund Lakhani

  - by Pinal Dave

  This is a fantastic blog post from my dear friend Balmukund ( blog | twitter | facebook ). He had presented a fantastic session in our last UG and there were lots of requests from attendees that he blogs about it. Well, here is the blog post about the same very popular UG session. Let us read the entire blog post in the voice of the Balmukund himself. During my last session in SQL Bangalore User Group (Facebook) meeting, I was lucky enough to deliver a session on SQL Server Startup issue. The name of the session was “SQL Engine Starting Trouble – How to start?” From the feedback, I realized that one of the “not well known” startup parameter is “-m”. Okay, you might say “I know that this is used to start the SQL in single user mode”. But what you might not know is that you can pass a string with -m which has special meaning and use. I have used this parameter in my blog here but looks like not many of you have seen that. It happens most of the time when we want to start SQL Server in single user mode, someone else makes connection before you can. The only choice you have is to repeat same process again till you succeed. Some smart DBAs may disable the remote network protocols (TCP/IP and Named Pipes) of SQL Instance and allow only local connections to SQL. Once the activity is complete, our dear smart DBA has to remember to re-enable network protocols. Sometimes, it may be a local service or application getting connection to SQL before we can. There is a better way to deal with it. Yes, you have guessed it correctly: -m parameter which a string. Since I work with SQL Product Support team, I may know little more undocumented commands and parameters, but this is not an undocumented stuff. It’s already documented in books online. So in this blog, I am going to show a demo of its usage. As documentation shows, “Do not use this option as a security feature.” So please read this blog as knowledge enhancer and troubleshooting issues not security feature. In my laptop, I have a default instance of SQL Server 2012 and here is what we would in the configuration manager. Now, I would go ahead and stop SQL Service by selecting SQL Server (MSSQLServer) > Right Click > Stop. There are multiple ways to start SQL with startup parameter. 1) Use Net Start Command from command prompt Net Start MSSQLServer /mSQLCMD The above command is the simplest way to add startup parameter to SQL. This parameter would be cleared once we stop and start SQL. 2) Add Startup Parameter via configuration manager. Step is already listed here. We need to add -mSQLCMD If we compare 1 and 2, it’s clear that unless we modify startup parameter and remove -m, it would be in effect. 3) Start SQL Service via command line SQLServr.exe –mSQLCMD –s<InstanceName> Wait, what does SQLCMD mean with /m? It’s the instruction to SQL that start SQL Server in Single User Mode and allow only the application which is SQLCMD. Any other application would fail with Login Failed for User Error message. It would be important to note that string is case sensitive. This value should be picked up from application_name column from sys.dm_exec_sessions. I have made a connection using SQLCMD and as we can see it comes as upper case “SQLCMD”. If we want only management studio query windows to connect then we need to give -m” Microsoft SQL Server Management Studio – Query” as startup parameter. In below example, I have given it as SQLCMd (lower case d at the end) and we would notice that we would not be able to connect to SQL Instance. Above proves that parameter works as expected and it’s case sensitive. Error Log would show below information. How to get error log location? I have already blogged about it. Hope you have learned something new. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Server Management Studio, SQL Tips and Tricks, T SQL, Technology

  Read the article

• Bullet physics debug drawing not working

  - by Krishnabhadra

  Background I am following on from this question, which isn't answered yet. Basically I have a cube and a UVSphere in my scene, with UVSphere on the top of the cube without touching the cube. Both exported from blender. When I run the app The UVSphere does circle around the cube for 3 or 4 times and jump out of the scene. What I actually expect was the sphere to fall on top of the cube. What this question about From the comment to the linked question, I got to know about bullet debug drawing, which helps in debugging by drawing outline of physics bodies which are normally invisible. I did some research on that and came up with the code given below. From whatever I have read, below code should work, but it doesn't. My Code My bullet initialization code. -(void) initializeScene { /*Setup physics world*/ _physicsWorld = [[CC3PhysicsWorld alloc] init]; [_physicsWorld setGravity:0 y:-9.8 z:0]; /*Setting up debug draw*/ MyDebugDraw *draw = new MyDebugDraw; draw->setDebugMode(draw->getDebugMode() | btIDebugDraw::DBG_DrawWireframe ); _physicsWorld._discreteDynamicsWorld->setDebugDrawer(draw); /*Setup camera and lamb*/ ………….. //This simpleCube.pod contains the cube [self addContentFromPODFile: @"simpleCube.pod"]; //This file contains sphere [self addContentFromPODFile: @"SimpleSphere.pod"]; [self createGLBuffers]; CC3MeshNode* cubeNode = (CC3MeshNode*)[self getNodeNamed:@"Cube"]; CC3MeshNode* sphereNode = (CC3MeshNode*)[self getNodeNamed:@"Sphere"]; // both cubeNode and sphereNode are not nil from this point float *cVertexData = (float*)((CC3VertexArrayMesh*)cubeNode.mesh) .vertexLocations.vertices; int cVertexCount = ((CC3VertexArrayMesh*)cubeNode.mesh) .vertexLocations.vertexCount; btTriangleMesh* cTriangleMesh = new btTriangleMesh(); int offset = 0; for (int i = 0; i < (cVertexCount / 3); i++) { unsigned int index1 = offset; unsigned int index2 = offset+6; unsigned int index3 = offset+12; cTriangleMesh->addTriangle( btVector3(cVertexData[index1], cVertexData[index1+1], cVertexData[index1+2]), btVector3(cVertexData[index2], cVertexData[index2+1], cVertexData[index2+2]), btVector3(cVertexData[index3], cVertexData[index3+1], cVertexData[index3+2])); offset += 18; } [self releaseRedundantData]; /*Create a triangle mesh from the vertices*/ btBvhTriangleMeshShape* cTriMeshShape = new btBvhTriangleMeshShape(cTriangleMesh,true); btCollisionShape *sphereShape = new btSphereShape(1); gTriMeshObject = [_physicsWorld createPhysicsObjectTrimesh:cubeNode shape:cTriMeshShape mass:0 restitution:1.0 position:cubeNode.location]; sphereObject = [_physicsWorld createPhysicsObject:sphereNode shape:sphereShape mass:1 restitution:0.1 position:sphereNode.location]; sphereObject.rigidBody->setDamping(0.1,0.8); /*Enable debug drawing*/ _physicsWorld._discreteDynamicsWorld->debugDrawWorld(); } And My btIDebugDraw implementation (MyDebugDraw.h) //MyDebugDraw.h class MyDebugDraw: public btIDebugDraw{ int m_debugMode; public: virtual void drawLine(const btVector3& from,const btVector3& to ,const btVector3& color); virtual void drawContactPoint(const btVector3& PointOnB ,const btVector3& normalOnB,btScalar distance ,int lifeTime,const btVector3& color); virtual void reportErrorWarning(const char* warningString); virtual void draw3dText(const btVector3& location ,const char* textString); virtual void setDebugMode(int debugMode); virtual int getDebugMode() const; }; void MyDebugDraw::drawLine(const btVector3& from,const btVector3& to ,const btVector3& color){ LogInfo(@"Works!!"); glPushMatrix(); glColor4f(color.getX(), color.getY(), color.getZ(), 1.0); const GLfloat line[] = { from.getX()*1, from.getY()*1, from.getZ()*1, //point A to.getX()*1, to.getY()*1,to.getZ()*1 //point B }; glVertexPointer( 3, GL_FLOAT, 0, &line ); glPointSize( 5.0f ); glDrawArrays( GL_POINTS, 0, 2 ); glDrawArrays( GL_LINES, 0, 2 ); glPopMatrix(); } void MyDebugDraw::drawContactPoint(const btVector3 &PointOnB ,const btVector3 &normalOnB, btScalar distance ,int lifeTime, const btVector3 &color){ } void MyDebugDraw::reportErrorWarning(const char *warningString){ } void MyDebugDraw::draw3dText(const btVector3 &location , const char *textString){ } void MyDebugDraw::setDebugMode(int debugMode){ } int MyDebugDraw::getDebugMode() const{ return DBG_DrawWireframe; } My Problem The drawLine method is getting called. I can see the cube and sphere in place. Sphere again does some circling around the cube before jumping off. No debug lines are getting drawn.

  Read the article

• Context Issue in ASP.NET MVC 3 Unobtrusive Ajax

  - by imran_ku07

      Introduction:          One of the coolest feature you can find in ASP.NET MVC 3 is Unobtrusive Ajax and Unobtrusive Client Validation which separates the javaScript behavior and functionality from the contents of a web page. If you are migrating your ASP.NET MVC 2 (or 1) application to ASP.NET MVC 3 and leveraging the Unobtrusive Ajax feature then you will find that the this context in the callback function is not the same as in ASP.NET MVC 2(or 1). In this article, I will show you the issue and a simple solution.       Description:           The easiest way to understand the issue is to start with an example. Create an ASP.NET MVC 3 application. Then add the following javascript file references inside your page,   <script src="@Url.Content("~/Scripts/MicrosoftAjax.js")" type="text/javascript"></script> <script src="@Url.Content("~/Scripts/MicrosoftMvcAjax.js")" type="text/javascript"></script> <script src="@Url.Content("~/Scripts/jquery-1.4.4.min.js")" type="text/javascript"></script> <script src="@Url.Content("~/Scripts/jquery.unobtrusive-ajax.js")" type="text/javascript"></script>             Then add the following lines into your view,   @Ajax.ActionLink("About", "About", new AjaxOptions { OnSuccess = "Success" }) <script type="text/javascript"> function Success(data) { alert(this.innerHTML) } </script>              Next, disable Unobtrusive Ajax feature from web.config,   <add key="UnobtrusiveJavaScriptEnabled" value="false"/>              Then run your application and click the About link, you will see the alert window with "About" message on the screen. This shows that the this context in the callback function is the element which is clicked. Now, let's see what will happen when we leverage Unobtrusive Ajax feature. Now enable Unobtrusive Ajax feature from web.config,     <add key="UnobtrusiveJavaScriptEnabled" value="true"/>              Then run your application again and click the About link again, this time you will see the alert window with "undefined" message on the screen. This shows that the this context in the callback function is not the element which is clicked. Here, this context in the callback function is the Ajax settings object provided by jQuery. This may not be desirable because your callback function may need the this context as the element which triggers the Ajax request. The easiest way to make the this context as the element which triggers the Ajax request is to add this line in jquery.unobtrusive-ajax.js file just before $.ajax(options) line,   options.context = element;              Then run your application again and click the About link again, you will find that the this context in the callback function remains same whether you use Unobtrusive Ajax or not.       Summary:          In this article I showed you a breaking change and a simple workaround in ASP.NET MVC 3. If you are migrating your application from ASP.NET MVC 2(or 1) to ASP.NET MVC 3 and leveraging Unobtrusive Ajax feature then you need to consider this breaking change. Hopefully you will enjoy this article too.     SyntaxHighlighter.all()

  Read the article

• Editing sqlcmdvariable nodes in SSDT Publish Profile files using msbuild

  - by jamiet

  Publish profile files are a new feature of SSDT database projects that enable you to package up all environment-specific properties into a single file for use at publish time; I have written about them before at Publish Profile Files in SQL Server Data Tools (SSDT) and if it wasn’t obvious from that blog post, I’m a big fan! As I have used Publish Profile files more and more I have realised that there may be times when you need to edit those Publish profile files during your build process, you may think of such an operation as a kind of pre-processor step. In my case I have a sqlcmd variable called DeployTag, it holds a value representing the current build number that later gets inserted into a table using a Post-Deployment script (that’s a technique that I wrote about in Implementing SQL Server solutions using Visual Studio 2010 Database Projects – a compendium of project experiences – search for “Putting a build number into the DB”). Here are the contents of my Publish Profile file (simplified for demo purposes) : Notice that DeployTag defaults to “UNKNOWN”. On my current project we are using msbuild scripts to control what gets built and what I want to do is take the build number from our build engine and edit the Publish profile files accordingly. Here is the pertinent portion of the the msbuild script I came up with to do that:   <ItemGroup>     <Namespaces Include="myns">       <Prefix>myns</Prefix>       <Uri>http://schemas.microsoft.com/developer/msbuild/2003</Uri>     </Namespaces>   </ItemGroup>   <Target Name="UpdateBuildNumber">     <ItemGroup>       <SSDTPublishFiles Include="$(DESTINATION)\**\$(CONFIGURATION)\**\*.publish.xml" />     </ItemGroup>     <MSBuild.ExtensionPack.Xml.XmlFile Condition="%(SSDTPublishFiles.Identity) != ''"                                        TaskAction="UpdateElement"                                        File="%(SSDTPublishFiles.Identity)"                                        Namespaces="@(Namespaces)"                                         XPath="//myns:SqlCmdVariable[@Include='DeployTag']/myns:Value"                                         InnerText="$(BuildNumber)"/>   </Target> The important bits here are the definition of the namespace http://schemas.microsoft.com/developer/msbuild/2003: and the XPath expression //myns:SqlCmdVariable[@Include='DeployTag']/myns:Value: Some extra info: I use a fantastic tool called XMLPad to discover/test XPath expressions, read more at XMLPad – a new tool in my developer utility belt MSBuild.ExtensionPack.Xml.XmlFile is a msbuild task used to edit XML files and is available from Mike Fourie’s MSBuild Extension Pack I’m using a property called $(BuildNumber) to hold the value to substitute into the file and also $(DESTINATION)\**\$(CONFIGURATION)\**\*.publish.xml to define an ItemGroup all of my Publish Profile files. Populating those properties is basic msbuild stuff and is therefore outside the scope of this blog post however if you want to learn more check out MSBuild properties & How To: Use Wildcards to Build All Files in a Directory. Hope this is useful! @Jamiet

  Read the article

• Personal search – the future of search

  - by jamiet

  [Four months ago I wrote a meandering blog post on another blogging site entitled Personal search – the future of search. The points I made therein are becoming more relevant to what I'm reading about and hoping to get involved in in the future so I'm re-posting here to a wider audience to hopefully get some more feedback and guage reaction to it. This has been prompted by the book Pull by David Siegel that is forming my current holiday reading (recommended to me by a commenter on my previous post Interesting things – Twitter annotations and your phone as a web server) and in particular by Siegel's notion of us all in the future having a personal online data vault.] My one-time colleague Paul Dawson recently wrote an article called The Future of Search and in it he proposed some interesting ideas. Some choice quotes: The growth of Chinese search giant Baidu is an indicator that fully localised and tailored content and offerings have great traction with local audiences This trend is already driving an increase in the use of specialist searches … Look at how Farecast is now integrated into Bing for example, or how Flightstats is now integrated into Google. Search does not necessarily have to begin with a keyword, but could start instead with a click or a touch. Take a look at Retrievr. Start drawing a picture in the box and see what happens. This is certainly search without the need for typing in keywords search technology has advanced greatly in recent years. The recent launch of Microsoft Live Labs’ Pivot has given us a taste of what we can expect to see in the future This really got me thinking about where search might go in the future and as my mind wandered I realised that as the amount of data that we collect about ourselves increases so too will the need and the desire to search it. The amount of electronic data that exists about each and every person is increasing and in the near future I fully expect that we are going to be able to store personal data such as: A history of our location (in fact Google Latitude already offers this facility) Recordings of all our phone conversations Health information history (weight, blood pressure etc…) Energy usage Spending history What films we watch, what radio stations we listen to Voting history Of course, most of this stuff is already stored somewhere but crucially we don’t have easy access to it. My utilities supplier knows how much electricity I’m using but if I want to know for myself I have to go and dig through my statements (assuming I have kept them). Similarly my doctor probably has ready access to all of my health records, my bank knows exactly what I have spent my money on, my cable supplier knows what I watch on TV and my mobile phone supplier probably knows exactly where I am and where I’ve been for the past few years. Strange then that none of this electronic information is available to me in a way that I can really make use of it; after all, its MY information. Its MY data. I created it. That is set to change. As technologies mature and customers become more technically cognizant they will demand more access to the data that companies hold about them. The companies themselves will realise the benefit that they derive from giving users what they want and will embrace ways of providing it. As a result the amount of data that we store about ourselves is going to increase exponentially and the desire to search and derive value from that data is going to grow with it; we are about to enter the era of the “personal datastore” and we will want, and need, to search through it in order to make sense of it all. Its interesting then that today when we think of search we think of search engines and yet in these personal datastores we’re referring to data that search engines can’t touch because WE own it and we (hopefully) choose to keep it private. Someone, I know not who, is going to lead in this space by making it easy for us to search our data and retrieve information that we have either forgotten or maybe didn’t even know in the first place. We will learn new things about ourselves and about our habits; we will share these findings with whomever we choose; we will compare what we discover with others; we will collaborate for mutual benefit and, most of all, we will educate ourselves as to how to live our lives better. Search will be the means to that end, it will enable us to make sense of the wealth of information that we will collect day in day out. The future of search is personal, why would we be interested in anything else? @Jamiet Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

  Read the article

• MySQL Connector/Net 6.5.5 Maintenance Release has been released

  - by fernando

  MySQL Connector/Net 6.5.5, a new maintenance release of our 6.5 series, has been released.  This release is GA quality and is appropriate for use in production environments.  Please note that 6.6 is our latest driver series and is the recommended product for development. It is now available in source and binary form from http://dev.mysql.com/downloads/connector/net/#downloads and mirror sites (note that not all mirror sites may be up to date at this point-if you can't find this version on some mirror, please try again later or choose another download site.) The 6.5.5 version of MySQL Connector/Net brings the following fixes: - Fix for ArgumentNull exception when using Take().Count() in a LINQ to Entities query (bug MySql #64749, Oracle bug #13913047). - Fix for type varchar changed to bit when saving in Table Designer (Oracle bug #13916560). - Fix for error when trying to change the name of an Index on the Indexes/Keys editor; along with this fix now users can change the Index type of a new Index which could not be done   in previous versions, and when changing the Index name the change is reflected on the list view at the left side of the Index/Keys editor (Oracle bug #13613801). - Fix for stored procedure call using only its name with EF code first (MySql bug #64999, Oracle bug #14008699). - Fix for List.Contains generates a bunch of ORs instead of more efficient IN clause in   LINQ to Entities (Oracle bug #14016344, MySql bug #64934). - Fix for performance issue in generated EF query: .NET StartsWith/Contains/EndsWith produces MySql's locate instead of Like (MySql bug #64935, Oracle bug #14009363). - Fix for script generated for code first contains wrong alter table and wrong declaration for byte[] (MySql bug #64216, Oracle bug #13900091). - Fix and code contribution for bug Timed out sessions are removed without notification which allow to enable the Expired CallBack when Session Provider times out any session (bug MySql #62266 Oracle bug # 13354935) - Fix for Exception thrown when using cascade delete in an EDM Model-First in Entity Framework (Oracle bug #14008752, MySql bug #64779). - Fix for Session locking issue with MySqlSessionStateStore (MySql bug #63997, Oracble bug #13733054). - Fixed deleting a user profile using Profile provider (MySQL bug #64470, Oracle bug #13790123) - Fix for bug Cannot Create an Entity with a Key of Type String (MySQL bug #65289, Oracle bug #14540202). This fix checks if the type has a FixedLength facet set in order to create a char otherwise should create varchar, mediumtext or longtext types when using a String CLR type in Code First or Model First also tested in Database First. Unit tests added for Code First and ProviderManifest. - Fix for bug "CacheServerProperties can cause 'Packet too large' error". The issue was due to a missing reading of Max_allowed_packet server property when CacheServerProperties is in true, since the value was read only in the first connection but the following pooled connections had a wrong value causing a Packet too large error. Including also a unit test for this scenario. All unit test passed. MySQL Bug #66578 Orabug #14593547. - Fix for handling unnamed parameter in MySQLCommand. This fix allows the mysqlcommand to handle parameters without requiring naming (e.g. INSERT INTO Test (id,name) VALUES (?, ?) ) (MySQL Bug #66060, Oracle bug #14499549). - Fixed inheritance on Entity Framework Code First scenarios. Discriminator column is created using its correct type as varchar(128) (MySql bug #63920 and Oracle bug #13582335). - Fixed "Trying to customize column precision in Code First does not work" (MySql bug #65001, Oracle bug #14469048). - Fixed bug ASP.NET Membership database fails on MySql database UTF32 (MySQL bug #65144, Oracle bug #14495292). - Fix for MySqlCommand.LastInsertedId holding only 32 bit values (MySql bug #65452, Oracle bug #14171960) by changing   several internal declaration of lastinsertid from int to long. - Fixed "Decimal type should have digits at right of decimal point", now default is 2, but user's changes in   EDM designer are recognized (MySql bug #65127, Oracle bug #14474342). - Fix for NullReferenceException when saving an uninitialized row in Entity Framework (MySql bug #66066, Oracle bug #14479715). - Fix for error when calling RoleProvider.RemoveUserFromRole(): causes an exception due to a wrong table being used (MySql bug #65805, Oracle bug #14405338). - Fix for "Memory Leak on MySql.Data.MySqlClient.MySqlCommand", too many MemoryStream's instances created (MySql bug #65696, Oracle bug #14468204). - Added ANTLR attribution notice (Oracle bug #14379162). - Fixed Entity Framework + mysql connector/net in partial trust throws exceptions (MySql bug #65036, Oracle bug #14668820). - Added support in Parser for Datetime and Time types with precision when using Server 5.6 (No bug Number). - Small improvement on MySqlPoolManager CleanIdleConnections for better mysqlpoolmanager idlecleanuptimer at startup (MySql bug #66472 and Oracle bug #14652624). - Fix for bug TIMESTAMP values are mistakenly represented as DateTime with Kind = Local (Mysql bug #66964, Oracle bug #14740705). - Fix for bug Keyword not supported. Parameter name: AttachDbFilename (Mysql bug #66880, Oracle bug #14733472). - Added support to MySql script file to retrieve data when using "SHOW" statements. - Fix for Package Load Failure in Visual Studio 2005 (MySql bug #63073, Oracle bug #13491674). - Fix for bug "Unable to connect using IPv6 connections" (MySQL bug #67253, Oracle bug #14835718). - Added auto-generated values for Guid identity columns (MySql bug #67450, Oracle bug #15834176). - Fix for method FirstOrDefault not supported in some LINQ to Entities queries (MySql bug #67377, Oracle bug #15856964). The release is available to download at http://dev.mysql.com/downloads/connector/net/6.5.html Documentation ------------------------------------- You can view current Connector/Net documentation at http://dev.mysql.com/doc/refman/5.5/en/connector-net.html You can find our team blog at http://blogs.oracle.com/MySQLOnWindows. You can also post questions on our forums at http://forums.mysql.com/. Enjoy and thanks for the support! 

  Read the article

• Fusion HCM SaaS – Integration

  - by Kiran Mundy

  v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Fusion HCM SaaS – Integration A typical implementation pattern we’re seeing with Fusion Apps early adopters is implementing a few Fusion HCM applications that bring the most benefit to their company with the least disruption to existing programs and interfaces. Very often this ends up being Fusion Goals & Performance, Talent, Compensation or Benefits, often with Taleo for recruiting. The implementation picture looks like what you see below: Here, you can see that all the “downstream integrations” from the On-Premise Core HR, are unaffected because the master for employee data is still your On-Premise Core HR system – all updates and new hires are made here (although they may be fed in from Taleo to start with). As a second phase when customers migrate Core HR to Fusion HCM, they have to come up with a strategy to manage integrations to all their downstream applications that require employee details. For customers coming from EBS HR, a short term strategy that allows for minimal impact, is to extract employee data from Fusion (Via HCM Extract), and load the shared EBS HR tables (which are part of an EBS Financials install anyways), and let your downstream integrations continue to function based on this data as shown below. If you are not coming from EBS HR and there are license implications, you may want to consider: Creating an On-Premise warehouse for extracting data from Fusion Apps. Leveraging Fusion Apps Web Services (available to SaaS customers starting R7) to directly retrieve/write data to Fusion Apps. Integration Tools File Based Loader This is the primary mechanism for loading HCM data (both initial load and incremental updates) into Fusion HCM. Employee & related data can be uploaded into Fusion HCM using File Based Loader. Note that ability to schedule File Based Loader to run on a pre-defined schedule will be available as a patch on top of Rel 5. Hr2Hr has been deprecated in favor of File Based Loader, but for existing customers using Hr2Hr, here are some sample scripts that show how to get more informative error messages. They can be run by creating data model sql queries in BI Publisher. The scripts currently have hard coded values for request id and loader batch id, which your developer will need to update to the correct values for you. The BI Publisher Training Session recorded on Apr 18th is available here (under "Recordings"). This will enable a somewhat technical resource to create a data model sql query. Links to Documentation & Traning Reference documentation for File Based Loader on docs.oracle.com FBL 1.1 MOS Doc Id 1533860.1 Sample demo data files for File Based Loader HCM SaaS Integrations ppt and recording. EBS api's Loading Information into EBS Full or Shared HCM This could be candidate information being loaded from Taleo into EBS or  Employee information being loaded from Fusion HCM into an EBS shared HR install (for downstream applications & EBS Financials). Oracle HRMS Product Family Publicly Callable Business Process APIs (A Reference Consolidation) [ID 216838.1] This is a guide to the EBS R12 Integration Repository accessible from an EBS instance. EBS HRMS Publicly Callable Business Process APIs in Release 11i & 12 [ID 121964.1] Fusion HCM Extract Fusion HCM Extract is the primary mechanism used to extract employee information from Fusion HCM. Refer to the "Configure Identity Sync" doc on MOS  for additional mechanisms. Additional documentation (you'll need an oracle.com account to access) HCM Extracts User Guides (Rel 4 & 5) HCM Extract Entity/Attributes (Rel 5) HCM Extract User Guide (Rel 5) If you don’t have an oracle.com account, download the zipped HCM Extract Rel 5 Docs (Click on File --> Download on next screen). View Training Recordings on Fusion HCM Extract Benefits Extract To setup the benefits extract, refer to the following guide. Page 2-15 of the User Documentation describes how to use the benefits extract. Benefit enrollments can also be uploaded into Fusion Benefits. Instructions are here along with a sample upload file. However, if the defined benefits extract does not meet your requirements, you can use BI Publisher (Link to BI Publisher presentation recording from Apr 18th) to create your own version of Benefits extract. You can start with the data model query underlying the benefits extract. Payroll Interface Fusion Payroll Interface enables you to capture personal payroll information, such as earnings and deductions, along with other data from Oracle Fusion Human Capital Management, and send that information to a third-party payroll provider. Documentation: Payroll interface guide Sample file DBI's used for the payroll interface.Usage Patterns always accessible @ http://www.finapps.com Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";}

  Read the article

• Use Drive Mirroring for Instant Backup in Windows 7

  - by Trevor Bekolay

  Even with the best backup solution, a hard drive crash means you’ll lose a few hours of work. By enabling drive mirroring in Windows 7, you’ll always have an up-to-date copy of your data. Windows 7’s mirroring – which is only available in Professional, Enterprise, and Ultimate editions – is a software implementation of RAID 1, which means that two or more disks are holding the exact same data. The files are constantly kept in sync, so that if one of the disks fails, you won’t lose any data. Note that mirroring is not technically a backup solution, because if you accidentally delete a file, it’s gone from both hard disks (though you may be able to recover the file). As an additional caveat, having mirrored disks requires changing them to “dynamic disks,” which can only be read within modern versions of Windows (you may have problems working with a dynamic disk in other operating systems or in older versions of Windows). See this Wikipedia page for more information. You will need at least one empty disk to set up disk mirroring. We’ll show you how to mirror an existing disk (of equal or lesser size) without losing any data on the mirrored drive, and how to set up two empty disks as mirrored copies from the get-go. Mirroring an Existing Drive Click on the start button and type partitions in the search box. Click on the Create and format hard disk partitions entry that shows up. Alternatively, if you’ve disabled the search box, press Win+R to open the Run window and type in: diskmgmt.msc The Disk Management window will appear. We’ve got a small disk, labeled OldData, that we want to mirror in a second disk of the same size. Note: The disk that you will use to mirror the existing disk must be unallocated. If it is not, then right-click on it and select Delete Volume… to mark it as unallocated. This will destroy any data on that drive. Right-click on the existing disk that you want to mirror. Select Add Mirror…. Select the disk that you want to use to mirror the existing disk’s data and press Add Mirror. You will be warned that this process will change the existing disk from basic to dynamic. Note that this process will not delete any data on the disk! The new disk will be marked as a mirror, and it will starting copying data from the existing drive to the new one. Eventually the drives will be synced up (it can take a while), and any data added to the E: drive will exist on both physical hard drives. Setting Up Two New Drives as Mirrored If you have two new equal-sized drives, you can format them to be mirrored copies of each other from the get-go. Open the Disk Management window as described above. Make sure that the drives are unallocated. If they’re not, and you don’t need the data on either of them, right-click and select Delete volume…. Right-click on one of the unallocated drives and select New Mirrored Volume…. A wizard will pop up. Click Next. Click on the drives you want to hold the mirrored data and click Add. Note that you can add any number of drives. Click Next. Assign it a drive letter that makes sense, and then click Next. You’re limited to using the NTFS file system for mirrored drives, so enter a volume label, enable compression if you want, and then click Next. Click Finish to start formatting the drives. You will be warned that the new drives will be converted to dynamic disks. And that’s it! You now have two mirrored drives. Any files added to E: will reside on both physical disks, in case something happens to one of them. Conclusion While the switch from basic to dynamic disks can be a problem for people who dual-boot into another operating system, setting up drive mirroring is an easy way to make sure that your data can be recovered in case of a hard drive crash. Of course, even with drive mirroring, we advocate regular backups to external drives or online backup services. Similar Articles Productive Geek Tips Rebit Backup Software [Review]Disabling Instant Search in Outlook 2007Restore Files from Backups on Windows Home ServerSecond Copy 7 [Review]Backup Windows Home Server Folders to an External Hard Drive TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 VMware Workstation 7 Acronis Online Backup Windows Firewall with Advanced Security – How To Guides Sculptris 1.0, 3D Drawing app AceStock, a Tiny Desktop Quote Monitor Gmail Button Addon (Firefox) Hyperwords addon (Firefox) Backup Outlook 2010

  Read the article

• Retrieve Performance Data from SOA Infrastructure Database

  - by fip

  My earlier blog posting shows how to enable, retrieve and interpret BPEL engine performance statistics to aid performance troubleshooting. The strength of BPEL engine statistics at EM is its break down per request. But there are some limitations with the BPEL performance statistics mentioned in that blog posting: The statistics were stored in memory instead of being persisted. To avoid memory overflow, the data are stored to a buffer with limited size. When the statistic entries exceed the limitation, old data will be flushed out to give ways to new statistics. Therefore it can only keep the last X number of entries of data. The statistics 5 hour ago may not be there anymore. The BPEL engine performance statistics only includes latencies. It does not provide throughputs. Fortunately, Oracle SOA Suite runs with the SOA Infrastructure database and a lot of performance data are naturally persisted there. It is at a more coarse grain than the in-memory BPEL Statistics, but it does have its own strengths as it is persisted. Here I would like offer examples of some basic SQL queries you can run against the infrastructure database of Oracle SOA Suite 11G to acquire the performance statistics for a given period of time. You can run it immediately after you modify the date range to match your actual system. 1. Asynchronous/one-way messages incoming rates The following query will show number of messages sent to one-way/async BPEL processes during a given time period, organized by process names and states select composite_name composite, state, count(*) Count from dlv_message where receive_date >= to_timestamp('2012-10-24 21:00:00','YYYY-MM-DD HH24:MI:SS') and receive_date <= to_timestamp('2012-10-24 21:59:59','YYYY-MM-DD HH24:MI:SS') group by composite_name, state order by Count; 2. Throughput of BPEL process instances The following query shows the number of synchronous and asynchronous process instances created during a given time period. It list instances of all states, including the unfinished and faulted ones. The results will include all composites cross all SOA partitions select state, count(*) Count, composite_name composite, component_name,componenttype from cube_instance where creation_date >= to_timestamp('2012-10-24 21:00:00','YYYY-MM-DD HH24:MI:SS') and creation_date <= to_timestamp('2012-10-24 21:59:59','YYYY-MM-DD HH24:MI:SS') group by composite_name, component_name, componenttype order by count(*) desc; 3. Throughput and latencies of BPEL process instances This query is augmented on the previous one, providing more comprehensive information. It gives not only throughput but also the maximum, minimum and average elapse time BPEL process instances. select composite_name Composite, component_name Process, componenttype, state, count(*) Count, trunc(Max(extract(day from (modify_date-creation_date))*24*60*60 + extract(hour from (modify_date-creation_date))*60*60 + extract(minute from (modify_date-creation_date))*60 + extract(second from (modify_date-creation_date))),4) MaxTime, trunc(Min(extract(day from (modify_date-creation_date))*24*60*60 + extract(hour from (modify_date-creation_date))*60*60 + extract(minute from (modify_date-creation_date))*60 + extract(second from (modify_date-creation_date))),4) MinTime, trunc(AVG(extract(day from (modify_date-creation_date))*24*60*60 + extract(hour from (modify_date-creation_date))*60*60 + extract(minute from (modify_date-creation_date))*60 + extract(second from (modify_date-creation_date))),4) AvgTime from cube_instance where creation_date >= to_timestamp('2012-10-24 21:00:00','YYYY-MM-DD HH24:MI:SS') and creation_date <= to_timestamp('2012-10-24 21:59:59','YYYY-MM-DD HH24:MI:SS') group by composite_name, component_name, componenttype, state order by count(*) desc;   4. Combine all together Now let's combine all of these 3 queries together, and parameterize the start and end time stamps to make the script a bit more robust. The following script will prompt for the start and end time before querying against the database: accept startTime prompt 'Enter start time (YYYY-MM-DD HH24:MI:SS)' accept endTime prompt 'Enter end time (YYYY-MM-DD HH24:MI:SS)' Prompt "==== Rejected Messages ===="; REM 2012-10-24 21:00:00 REM 2012-10-24 21:59:59 select count(*), composite_dn from rejected_message where created_time >= to_timestamp('&&StartTime','YYYY-MM-DD HH24:MI:SS') and created_time <= to_timestamp('&&EndTime','YYYY-MM-DD HH24:MI:SS') group by composite_dn; Prompt " "; Prompt "==== Throughput of one-way/asynchronous messages ===="; select state, count(*) Count, composite_name composite from dlv_message where receive_date >= to_timestamp('&StartTime','YYYY-MM-DD HH24:MI:SS') and receive_date <= to_timestamp('&EndTime','YYYY-MM-DD HH24:MI:SS') group by composite_name, state order by Count; Prompt " "; Prompt "==== Throughput and latency of BPEL process instances ====" select state, count(*) Count, trunc(Max(extract(day from (modify_date-creation_date))*24*60*60 + extract(hour from (modify_date-creation_date))*60*60 + extract(minute from (modify_date-creation_date))*60 + extract(second from (modify_date-creation_date))),4) MaxTime, trunc(Min(extract(day from (modify_date-creation_date))*24*60*60 + extract(hour from (modify_date-creation_date))*60*60 + extract(minute from (modify_date-creation_date))*60 + extract(second from (modify_date-creation_date))),4) MinTime, trunc(AVG(extract(day from (modify_date-creation_date))*24*60*60 + extract(hour from (modify_date-creation_date))*60*60 + extract(minute from (modify_date-creation_date))*60 + extract(second from (modify_date-creation_date))),4) AvgTime, composite_name Composite, component_name Process, componenttype from cube_instance where creation_date >= to_timestamp('&StartTime','YYYY-MM-DD HH24:MI:SS') and creation_date <= to_timestamp('&EndTime','YYYY-MM-DD HH24:MI:SS') group by composite_name, component_name, componenttype, state order by count(*) desc;  

  Read the article

• FairScheduling Conventions in Hadoop

  - by dan.mcclary

  While scheduling and resource allocation control has been present in Hadoop since 0.20, a lot of people haven't discovered or utilized it in their initial investigations of the Hadoop ecosystem. We could chalk this up to many things: Organizations are still determining what their dataflow and analysis workloads will comprise Small deployments under tests aren't likely to show the signs of strains that would send someone looking for resource allocation options The default scheduling options -- the FairScheduler and the CapacityScheduler -- are not placed in the most prominent position within the Hadoop documentation. However, for production deployments, it's wise to start with at least the foundations of scheduling in place so that you can tune the cluster as workloads emerge. To do that, we have to ask ourselves something about what the off-the-rack scheduling options are. We have some choices: The FairScheduler, which will work to ensure resource allocations are enforced on a per-job basis. The CapacityScheduler, which will ensure resource allocations are enforced on a per-queue basis. Writing your own implementation of the abstract class org.apache.hadoop.mapred.job.TaskScheduler is an option, but usually overkill. If you're going to have several concurrent users and leverage the more interactive aspects of the Hadoop environment (e.g. Pig and Hive scripting), the FairScheduler is definitely the way to go. In particular, we can do user-specific pools so that default users get their fair share, and specific users are given the resources their workloads require. To enable fair scheduling, we're going to need to do a couple of things. First, we need to tell the JobTracker that we want to use scheduling and where we're going to be defining our allocations. We do this by adding the following to the mapred-site.xml file in HADOOP_HOME/conf: <property> <name>mapred.jobtracker.taskScheduler</name> <value>org.apache.hadoop.mapred.FairScheduler</value> </property> <property> <name>mapred.fairscheduler.allocation.file</name> <value>/path/to/allocations.xml</value> </property> <property> <name>mapred.fairscheduler.poolnameproperty</name> <value>pool.name</value> </property> <property> <name>pool.name</name> <value>${user.name}</name> </property> What we've done here is simply tell the JobTracker that we'd like to task scheduling to use the FairScheduler class rather than a single FIFO queue. Moreover, we're going to be defining our resource pools and allocations in a file called allocations.xml For reference, the allocation file is read every 15s or so, which allows for tuning allocations without having to take down the JobTracker. Our allocation file is now going to look a little like this <?xml version="1.0"?> <allocations> <pool name="dan"> <minMaps>5</minMaps> <minReduces>5</minReduces> <maxMaps>25</maxMaps> <maxReduces>25</maxReduces> <minSharePreemptionTimeout>300</minSharePreemptionTimeout> </pool> <mapreduce.job.user.name="dan"> <maxRunningJobs>6</maxRunningJobs> </user> <userMaxJobsDefault>3</userMaxJobsDefault> <fairSharePreemptionTimeout>600</fairSharePreemptionTimeout> </allocations> In this case, I've explicitly set my username to have upper and lower bounds on the maps and reduces, and allotted myself double the number of running jobs. Now, if I run hive or pig jobs from either the console or via the Hue web interface, I'll be treated "fairly" by the JobTracker. There's a lot more tweaking that can be done to the allocations file, so it's best to dig down into the description and start trying out allocations that might fit your workload.

  Read the article

• Create a Social Community of Trust Along With Your Federal Digital Services Governance

  - by TedMcLaughlan

  The Digital Services Governance Recommendations were recently released, supporting the US Federal Government's Digital Government Strategy Milestone Action #4.2 to establish agency-wide governance structures for developing and delivering digital services. Figure 1 - From: "Digital Services Governance Recommendations" While extremely important from a policy and procedure perspective within an Agency's information management and communications enterprise, these recommendations only very lightly reference perhaps the most important success enabler - the "Trusted Community" required for ultimate usefulness of the services delivered. By "ultimate usefulness", I mean the collection of public, transparent properties around government information and digital services that include social trust and validation, social reach, expert respect, and comparative, standard measures of relative value. In other words, do the digital services meet expectations of the public, social media ecosystem (people AND machines)? A rigid governance framework, controlling by rules, policies and roles the creation and dissemination of digital services may meet the expectations of direct end-users and most stakeholders - including the agency information stewards and security officers. All others who may share comments about the services, write about them, swap or review extracts, repackage, visualize or otherwise repurpose the output for use in entirely unanticipated, social ways - these "stakeholders" will not be governed, but may observe guidance generated by a "Trusted Community". As recognized members of the trusted community, these stakeholders may ultimately define the right scope and detail of governance that all other users might observe, promoting and refining the usefulness of the government product as the social ecosystem expects. So, as part of an agency-centric governance framework, it's advised that a flexible governance model be created for stewarding a "Community of Trust" around the digital services. The first steps follow the approach outlined in the Recommendations: Step 1: Gather a Core Team In addition to the roles and responsibilities described, perhaps a set of characteristics and responsibilities can be developed for the "Trusted Community Steward/Advocate" - i.e. a person or team who (a) are entirely cognizant of and respected within the external social media communities, and (b) are trusted both within the agency and outside as practical, responsible, non-partisan communicators of useful information. The may seem like a standard Agency PR/Outreach team role - but often an agency or stakeholder subject matter expert with a public, active social persona works even better. Step 2: Assess What You Have In addition to existing, agency or stakeholder decision-making bodies and assets, it's important to take a PR/Marketing view of the social ecosystem. How visible are the services across the social channels utilized by current or desired constituents of your agency? What's the online reputation of your agency and perhaps the service(s)? Is Search Engine Optimization (SEO) a facet of external communications/publishing lifecycles? Who are the public champions, instigators, value-adders for the digital services, or perhaps just influential "communicators" (i.e. with no stake in the game)? You're essentially assessing your market and social presence, and identifying the actors (including your own agency employees) in the existing community of trust. Step 3: Determine What You Want The evolving Community of Trust will most readily absorb, support and provide feedback regarding "Core Principles" (Element B of the "six essential elements of a digital services governance structure") shared by your Agency, and obviously play a large, though probably very unstructured part in Element D "Stakeholder Input and Participation". Plan for this, and seek input from the social media community with respect to performance metrics - these should be geared around the outcome and growth of the trusted communities actions. How big and active is this community? What's the influential reach of this community with respect to particular messaging or campaigns generated by the Agency? What's the referral rate TO your digital services, FROM channels owned or operated by members of this community? (this requires governance with respect to content generation inclusive of "markers" or "tags"). At this point, while your Agency proceeds with steps 4 ("Build/Validate the Governance Structure") and 5 ("Share, Review, Upgrade"), the Community of Trust might as well just get going, and start adding value and usefulness to the existing conversations, existing data services - loosely though directionally-stewarded by your trusted advocate(s). Why is this an "Enterprise Architecture" topic? Because it's increasingly apparent that a Public Service "Enterprise" is not wholly contained within Agency facilities, firewalls and job titles - it's also manifested in actual, perceived or representative forms outside the walls, on the social Internet. An Agency's EA model and resulting investments both facilitate and are impacted by the "Social Enterprise". At Oracle, we're very active both within our Enterprise and outside, helping foster social architectures that enable truly useful public services, digital or otherwise.

  Read the article

• [GEEK SCHOOL] Network Security 3: Windows Defender and a Malware-Free System

  - by Ciprian Rusen

  In this second lesson we are going to talk about one of the most confusing security products that are bundled with Windows: Windows Defender. In the past, this product has had a bad reputation and for good reason – it was very limited in its capacity to protect your computer from real-world malware. However, the latest version included in Windows 8.x operating systems is much different than in the past and it provides real protection to its users. The nice thing about Windows Defender in its current incarnation, is that it protects your system from the start, so there are never gaps in coverage. We will start this lesson by explaining what Windows Defender is in Windows 7 and Vista versus what it is in Windows 8, and what product to use if you are using an earlier version. We next will explore how to use Windows Defender, how to improve its default settings, and how to deal with the alerts that it displays. As you will see, Windows Defender will have you using its list of quarantined items a lot more often than other security products. This is why we will explain in detail how to work with it and remove malware for good or restore those items that are only false alarms. Lastly, you will learn how to turn off Windows Defender if you no longer want to use it and you prefer a third-party security product in its place and then how to enable it back, if you have changed your mind about using it. Upon completion, you should have a thorough understanding of your system’s default anti-malware options, or how to protect your system expeditiously. What is Windows Defender? Unfortunately there is no one clear answer to this question because of the confusing way Microsoft has chosen to name its security products. Windows Defender is a different product, depending on the Windows operating system you are using. If you use Windows Vista or Windows 7, then Windows Defender is a security tool that protects your computer from spyware. This but one form of malware made out of tools and applications that monitor your movements on the Internet or the activities you make on your computer. Spyware tends to send the information that is collected to a remote server and it is later used in all kinds of malicious purposes, from displaying advertising you don’t want, to using your personal data, etc. However, there are many other types of malware on the Internet and this version of Windows Defender is not able to protect users from any of them. That’s why, if you are using Windows 7 or earlier, we strongly recommend that you disable Windows Defender and install a more complete security product like Microsoft Security Essentials, or third-party security products from specialized security vendors. If you use Windows 8.x operating systems, then Windows Defender is the same thing as Microsoft Security Essentials: a decent security product that protects your computer in-real time from viruses and spyware. The fact that this product protects your computer also from viruses, not just from spyware, makes a huge difference. If you don’t want to pay for security products, Windows Defender in Windows 8.x and Microsoft Security Essentials (in Windows 7 or earlier) are good alternatives. Windows Defender in Windows 8.x and Microsoft Security Essentials are the same product, only their name is different. In this lesson, we will use the Windows Defender version from Windows 8.x but our instructions apply also to Microsoft Security Essentials (MSE) in Windows 7 and Windows Vista. If you want to download Microsoft Security Essentials and try it out, we recommend you to use this page: Download Microsoft Security Essentials. There you will find both 32-bit and 64-bit editions of this product as well versions in multiple languages. How to Use and Configure Windows Defender Using Windows Defender (MSE) is very easy to use. To start, search for “defender” on the Windows 8.x Start screen and click or tap the “Windows Defender” search result. In Windows 7, search for “security” in the Start Menu search box and click “Microsoft Security Essentials”. Windows Defender has four tabs which give you access to the following tools and options: Home – here you can view the security status of your system. If everything is alright, then it will be colored in green. If there are some warnings to consider, then it will be colored in yellow, and if there are threats that must be dealt with, everything will be colored in red. On the right side of the “Home” tab you will find options for scanning your computer for viruses and spyware. On the bottom of the tab you will find information about when the last scan was performed and what type of scan it was. Update – here you will find information on whether this product is up-to-date. You will learn when it was last updated and the versions of the definitions it is using. You can also trigger a manual update. History – here you can access quarantined items, see which items you’ve allowed to run on your PC even if they were identified as malware by Windows Defender, and view a complete list with all the malicious items Windows Defender has detected on your PC. In order to access all these lists and work with them, you need to be signed in as an administrator. Settings – this is the tab where you can turn on the real-time protection service, exclude files, file types, processes, and locations from its scans as well as access a couple of more advanced settings. The only difference between Windows Defender in Windows 8.x and Microsoft Security Essentials (in Windows 7 or earlier) is that, in the “Settings” tab, Microsoft Security Essentials allows you to set when to run scheduled scans while Windows Defender lacks this option.

  Read the article

• Understanding each other in web development

  - by Pete Hotchkin

  During my career I have been lucky enough to work in several different roles within web development with many extremely talented people, from incredible designers who were passionate about the placement of every pixel right through to server administrators and DBAs who were always measuring the improvements they were making to their queries in the smallest possible unit. The problem I always faced was that more often than not I was stuck in the middle trying to mediate between these different functions and enable each side to understand the other’s point of view. The main areas of contention that there have always been between these functional groups in my experience have been at 2 key points: during the build phase and then when there is a problem post-build. During both of these times it is often easier for someone to pass the buck onto someone else than spend the time to understand the other person’s perspective. Below is a quick look at two upcoming tools that will not only speed up the build phase for each function, but  also help when it comes to the issues faced once a site has been pushed live. In my experience a web project goes through several phases of development. The first of these is design, generally handled as Photoshop files which are then passed onto a front-end developer. This is the first point at which heated discussions can arise. One problem I’ve seen several times is that the designer doesn’t fully understand the platform constraints that need to be considered, and as a result has designed something that does not translate very well or is simply not possible. Working at Red Gate, I am lucky enough to be able to meet some amazing people and this happened just the other day when I was introduced to Neil Kinnish and Pete Nelson, the creators of what I believe could be a great asset in this designer-developer relationship, Mixture. Mixture allows the front end developer to quickly prototype a web page with built-in frameworks such as bootstrap. It’s not an IDE however, it just sits there in the background and monitors the project files in the background so every time you save a file from your favorite IDE, it will compile things like LESS, compact your JavaScript and the automatically refresh your test browser so you can see the changes instantly. I think one of the best parts of this however is a single button that pushes the changed files up to the web so the designer can instantly see how far the developer has got and the problem that he is facing at that time without the need to spend time setting up a remote server. I can see this being a real asset to remote teams where there needs to be a compromise between the designer and the front-end developer, or just to allow the designer to see how the build is progressing and suggest small alterations. Once the design has been built into the front end the designer’s job is generally done and there are no other points of contention between the designer and the other functions involved in building these web projects. As the project moves into the stage of integrating it into the back end and deploying it to the production server other functions start to be pulled in and other issues arise such as the back-end developer understanding the frameworks that they are using such as the routes that are in place in an MVC application or the number of database calls that the ORM layer is actually making. There are many tools out there that can actually help with these problems such as mini profiler that gives you a quick snapshot of what is going on directly in the browser. For a slightly more in-depth look at what is happening and to gain a deeper understanding of an application you may be working on though, you may want to consider Glimpse. Created by Nik and Anthony, it is an application that sits at the bottom of your browser (installed via NuGet) which can show you information about how your application is pieced together and how the information on screen is being delivered as it happens. With a wealth of community-built plugins such as one for nHibernate and linq2SQL (full list of plugins on NuGet). It can be customized directly to your own setup to truly delve into the code to see what is happening, and can help to reduce the number of confusing moments about whether it is your code that is going wrong or whether there is something more sinister happening directly on the server. All the tools that I have mentioned in this post help to do one thing above all, and that is to ease the barrier of understanding between the different functions that are involved in building and maintaining a web application. In my experience it is very easy to say “Well, that’s not my problem”, simply because the two functions involved don’t truly understand the other’s point of view. Software should not only be seen as a way to streamline our own working process or as a debugging tool but also a communication aid to improve the entire lifecycle of a web project. Glimpse is actually the project that I am the designer on and I would love to get your feedback if you do decide to try it out or if you would like to share your own experiences of working on web projects please fill in your details at https://www.surveymk.com/s/joinGlimpse  or add a comment below and I will get in touch with you.

  Read the article

• ACORD LOMA Session Highlights Policy Administration Trends

  - by [email protected]

  Helen Pitts, senior product marketing manager for Oracle Insurance, attended and is blogging from the ACORD LOMA Insurance Forum this week. Above: Paul Vancheri, Chief Information Officer, Fidelity Investments Life Insurance Company. Vancheri gave a presentation during the ACORD LOMA Insurance Systems Forum about the key elements of modern policy administration systems and how insurers can mitigate risk during legacy system migrations to safely introduce new technologies. When I had a few particularly challenging honors courses in college my father, a long-time technology industry veteran, used to say, "If you don't know how to do something go ask the experts. Find someone who has been there and done that, don't be afraid to ask the tough questions, and apply and build upon what you learn." (Actually he still offers this same advice today.) That's probably why my favorite sessions at industry events, like the ACORD LOMA Insurance Forum this week, are those that include insight on industry trends and case studies from carriers who share their experiences and offer best practices based upon their own lessons learned. I had the opportunity to attend a particularly insightful session Wednesday as Craig Weber, senior vice president of Celent's Insurance practice, and Paul Vancheri, CIO of Fidelity Life Investments, presented, "Managing the Dynamic Insurance Landscape: Enabling Growth and Profitability with a Modern Policy Administration System." Policy Administration Trends Growing the business is the top issue when it comes to IT among both life and annuity and property and casualty carriers according to Weber. To drive growth and capture market share from competitors, carriers are looking to modernize their core insurance systems, with 65 percent of those CIOs participating in recent Celent research citing plans to replace their policy administration systems. Weber noted that there has been continued focus and investment, particularly in the last three years, by software and technology vendors to offer modern, rules-based, configurable policy administration solutions. He added that these solutions are continuing to evolve with the ongoing aim of helping carriers rapidly meet shifting business needs--whether it is to launch new products to market faster than the competition, adapt existing products to meet shifting consumer and /or regulatory demands, or to exit unprofitable markets. He closed by noting the top four trends for policy administration either in the process of being adopted today or on the not-so-distant horizon for the future: Underwriting and service desktops New business automation Convergence of ultra-configurable and domain content-rich systems Better usability and screen design Mitigating the Risk When Making the Decision to Modernize Third-party analyst research from advisory firms like Celent was a key part of the due diligence process for Fidelity as it sought a replacement for its legacy policy administration system back in 2005, according to Vancheri. The company's business opportunities were outrunning system capability. Its legacy system had not been upgraded in several years and was deficient from a functionality and currency standpoint. This was constraining the carrier's ability to rapidly configure and bring new and complex products to market. The company sought a new, modern policy administration system, one that would enable it to keep pace with rapid and often unexpected industry changes and ahead of the competition. A cross-functional team that included representatives from finance, actuarial, operations, client services and IT conducted an extensive selection process. This process included deep documentation review, pilot evaluations, demonstrations of required functionality and complex problem-solving, infrastructure integration capability, and the ability to meet the company's desired cost model. The company ultimately selected an adaptive policy administration system that met its requirements to: Deliver ease of use - eliminating paper and rework, while easing the burden on representatives to sell and service annuities Provide customer parity - offering Web-based capabilities in alignment with the company's focus on delivering a consistent customer experience across its business Deliver scalability, efficiency - enabling automation, while simplifying and standardizing systems across its technology stack Offer desired functionality - supporting Fidelity's product configuration / rules management philosophy, focus on customer service and technology upgrade requirements Meet cost requirements - including implementation, professional services and licenses fees and ongoing maintenance Deliver upon business requirements - enabling the ability to drive time to market for new products and flexibility to make changes Best Practices for Addressing Implementation Challenges Based upon lessons learned during the company's implementation, Vancheri advised carriers to evaluate staffing capabilities and cultural impacts, review business requirements to avoid rebuilding legacy processes, factor in dependent systems, and review policies and practices to secure customer data. His formula for success: upfront planning + clear requirements = precision execution. Achieving a Return on Investment Vancheri said the decision to replace their legacy policy administration system and deploy a modern, rules-based system--before the economic downturn occurred--has been integral in helping the company adapt to shifting market conditions, while enabling growth in its direct channel sales of variable annuities. Since deploying its new policy admin system, the company has reduced its average time to market for new products from 12-15 months to 4.5 months. The company has since migrated its other products to the new system and retired its legacy system, significantly decreasing its overall product development cycle. From a processing standpoint Vancheri noted the company has achieved gains in automation, information, and ease of use, resulting in improved real-time data edits, controls for better quality, and tax handling capability. Plus, with by having only one platform to manage, the company has simplified its IT environment and is well positioned to deliver system enhancements for greater efficiencies. Commitment to Continuing the Investment In the short and longer term future Vancheri said the company plans to enhance business functionality to support money movement, wire automation, divorce processing on payout contracts and cost-based tracking improvements. It also plans to continue system upgrades to remain current as well as focus on further reducing cycle time, driving down maintenance costs, and integrating with other products. Helen Pitts is senior product marketing manager for Oracle Insurance focused on life/annuities and enterprise document automation.

  Read the article

• Oracle Business Intelligence Advanced - Hands-on Workshop para Parceiros - 18 a 21 de Janeiro

  - by Claudia Costa

  Workshop Description This FREE hands-on workshop highlights strengths of OBIEE 11g by providing attendees a hands-on experience with BI 11g product. OBIEE 11g has adopted the standardized infrastructure of Fusion Middleware to provide robust server capability along with highly anticipated advanced visualization components like Maps, Flash based charts, Scorecards and KPIs. This workshop focuses on new features and infrastructure components for the BI practitioners who are familiar with either OBIEE 10g or previous BI releases. After taking this course, Oracle Business Intelligence 11g Advanced, you will gain insight into OBIEE11g technology, reporting solutions and new features. Workshop provides opportunities to practice with OBIEE11g environment as hands on activities. Participant will gain in-depth understanding of new architecture of OBIEE 11g, security mode, installation/configuration as well as reporting aspects like, new ROLAP/MOLAP style hierarchical browsing, new chart types, Action Framework and Advanced Visualization. If you are a Business Intelligence practitioners and familiar with BI10g - you cannot afford to miss this 3-day workshop. Register Now! PresentationsBusiness Intelligence EE (OBIEE) 11g: Advanced Workshop ·         OBIEE 11g Overview ·         OBIEE 11g Architecture and Infrastructure ·         OBIEE 11g Installation, Configuration and Monitoring ·         OBIEE11g Security Model and BI Components ·         OBIEE 11g Homepage Overview ·         New Visualizations: Master-Detail Events, Charts, Hierarchies ·         Reports Building with OBIEE 11g and Catalog Management ·         Spatial Integration, Action Framework, Scorecards ·         OBIEE 11g Dashboards ·         OBIEE Integration Options  Lab OutlineOracle Business Intelligence (OBIEE) 11g: Advanced Workshop The labs enable OBIEE Core functionality through hands-on activities are based on a Oracle VirtualBox image with software and training samples pre-installed. This Advanced course has few labs optional during the workshop to allow for students to practice them on their own. The primary purpose of the workshop is to provide expertise of 11g features and infrastructure changes from 10g. Labs will allow you to explore concepts to: ·         Have a clear understanding of the OBIEE 11g architecture ·         Have a clear understanding of the OBIEE differentiators ·         OBIEE11g Security Model ·         OBIEE11g Environment Management ·         Report Building with OBIEE11g ·         OBIEE11g Dashboard and Homepage Environment ·         New Visualization features ·         Management of Reports, Dashboards and BI Catalog Objects Audience ·         Business Intelligence Evangelist ·         Business Intelligence Application Developer or Consultant ·         Data Warehouse Developer ·         Enterprise Architects ·         Industry Solutions Architects Prerequisites ·         Experience and Understanding of OBIEE 10g is required. ·         Good understanding of data modeling for reporting purpose ·         Strong experience with database technologies preferred Equipment RequirementsThis workshop requires attendees to provide their own laptops. Attendee laptops must meet the following minimum hardware/software requirements: OBIEE 11g environments requires at least 3 GB of RAM (4GB Preferred), without which student will not be able to complete labs. This workshop has environment that includes VM Image and also a software components that students will install on their laptop for the labs. ·         Minimum 3GB RAM. 25GB free disk space ·         Internet Explorer 7 ·         VirtualBox (the latest version) ·         Downloadable from http://www.virtualbox.org ·         WINRAR or 7zip ·         Downloadable from http://www.win-rar.com/download.html ·         Downloadable from http://www.7zip.com/ Attendees will be given a VirtualBox image for Oraclee BI 11g Workshop containing the software along with required toolset, database and data sets for the labs. AgendaThis class duration is 3 Days9:00am: Sign-in and Technical Set up9:30am : Workshop Starts5:00pm : Workhop Ends LocalHotel Holiday Inn Express - Porto Salvo - Lisboa This class is Free. Register early to confirm a seat! Oracle BI Advanced 11g Hands-on Workshop - Schedule Register Now! January 11-13, 2011: Kista, Sweden January 18-20, 2011: Lisbon, Portugal March 1-3, 2011: Reading, Berkshire, UK March 15-17, 2011: Colombes, Paris, France March 29-31, 2011: Amsterdam, Netherlands Questions? For registration questions please send an email to [email protected]. Para outras informações, por favor contacte Claudia Costa, telf: 214235027 ou pelo email   

  Read the article

• Resetting Your Oracle User Password with SQL Developer

  - by thatjeffsmith

  There’s nothing more annoying than having to email, call, or log a support ticket to have one of your accounts reset. This is no less annoying in the Oracle database. Those pesky security folks have determined that your password should only be valid for X days, and your time is up. Time to reset the password! Except…you can’t log into the database to reset your password. What now? Wait a second, look at this nifty thing I see in SQL Developer: Right click on my connection, reset password not available! Why not? The JDBC Driver Doesn’t Support This Operation We can’t make this call over the Oracle JDBC layer, because it hasn’t been implemented. However our primary interface, OCI, does indeed support this. In order to use the Oracle Call Interface (OCI), you need to have an Oracle Client on your machine. The good news is that this is fairly easy to get going. The Instant Client will do. You have two options, the full or ‘Lite’ Instant Clients. If you want SQL*Plus and the other client tools, go for the full. If you just want the basic drivers, go for the Lite. Either of these is fine, but mind the bit level and version of Oracle! Make sure you get a 32 bit Instant Client if you run 32 bit SQL Developer or 64 bit if you run 64 Here’s the download link What, you didn’t believe me? Mind the version of Oracle too! You want to be at the same level or higher of the database you’re working with. You can use a 11.2.0.3 client with 11.2.0.1 database but not a 10gR2 client with 11gR2 database. Clear as mud? Download and Extract Put it where you want – Program Files is as good as place as any if you have the rights. When you’re done, copy that directory path you extracted the archive to, because we’re going to add it to your Windows PATH environment variable. The easiest way to find this in Windows 7 is to open the Start dialog and type ‘path’. In Windows 8 you’ll cast your spell and wave at your screen until something happens. I recommend you put it up front so we find our DLLs first. Now with that set, let’s start up SQL Developer. Check the Connection Context menu again Bingo! What happened there? SQL Developer looks to see if it can find the OCI resources. Guess where it looks? That’s right, the PATH. If it finds what it’s looking for, and confirms the bit level is right, it will activate the Reset Password option. We have a Preference to ‘force’ an OCI/THICK connection that gives you a few other edge case features, but you do not need to enable this to activate the Reset Password. Not necessary, but won’t hurt anything either. There are a few actual benefits to using OCI powered connections, but that’s beyond the scope of today’s blog post…to be continued. Ok, so we’re ready to go. Now, where was I again? Oh yeah, my password has expired… Right click on your connection and now choose ‘Reset Password’ You’ll need to know your existing password and select a new one that meets your databases’s security standards. I Need Another Option, This Ain’t Working! If you have another account in the database, you can use the DBA Panel to reset a user’s password, or of course you can spark up a SQL*Plus session and issue the ALTER USER JEFF IDENTIFIED BY _________; command – but you knew this already, yes? I need more help ‘installing’ the Instant Client, help! There are lots and lots of resources out there on this subject. But I also know from personal experience that many of you have problems getting this to ‘work.’ The key things to remember is to download the right bit level AND make sure the client install directory is in your path. I know many folks that will just ‘install’ the Instant Client directly to one of their ‘bin’ type directories. You can do that if you want, but I prefer the cleaner method. Of course if you lack admin privs to change the PATH variable, that might be your only option. Or you could do what the original ORA- message indicated and ‘contact your DBA.’

  Read the article

• 3 Ways to Make Steam Even Faster

  - by Chris Hoffman

  Have you ever noticed how slow Steam’s built-in web browser can be? Do you struggle with slow download speeds? Or is Steam just slow in general? These tips will help you speed it up. Steam isn’t a game itself, so there are no 3D settings to change to achieve maximum performance. But there are some things you can do to speed it up dramatically. Speed Up the Steam Web Browser Steam’s built-in web browser — used in both the Steam store and in Steam’s in-game overlay to provide a web browser you can quickly use within games – can be frustratingly slow on many systems. Rather than the typical speed we’ve come to expect from Chrome, Firefox, or even Internet Explorer, Steam seems to struggle. When you click a link or go to a new page, there’s a noticeable delay before the new page appears — something that doesn’t happen in desktop browsers. Many people seem to have made peace with this slowness, accepting that Steam’s built-in browser is just bad. However, there’s a trick that will eliminate this delay on many systems and make the Steam web browser fast. This problem seems to arise from an incompatibility with the Automatically Detect Proxy Settings option, which is enabled by default on Windows. This is a compatibility option that very few people should actually need, so it’s safe to disable it. To disable this option, open the Internet Options dialog — press the Windows key to access the Start menu or Start screen, type Internet Options, and click the Internet Options shortcut. Select the Connections tab in the Internet Options window and click the LAN settings button. Uncheck the Automatically detect settings option here, then click OK to save your settings. If you experienced a significant delay every time a web page loaded in Steam’s web browser, it should now be gone. In the unlikely event that you encounter some sort of problem with your network connection, you could always re-enable this option. Increase Steam’s Game Download Speed Steam attempts to automatically select the nearest download server to your location. However, it may not always select the ideal download server. Or, in the case of high-traffic events like big seasonal sales and huge game launches, you may benefit from selecting a less-congested server. To do this, open Steam’s settings by clicking the Steam menu in Steam and selecting Settings. Click over to the Downloads tab and select the closest download server from the Download Region box. You should also ensure that Steam’s download bandwidth isn’t limited from here. You may want to restart Steam and see if your download speeds improve after changing this setting. In some cases, the closest server might not be the fastest. One a bit farther away could be faster if your local server is more congested, for example. Steam once provided information about content server load, which allowed you to select a regional server that wasn’t under high-load, but this information no longer seems to be available. Steam still provides a page that shows you the amount of download activity happening in different regions, including statistics about the difference in download speeds in different US states, but this information isn’t as useful. Accelerate Steam and Your Games One way to speed up all your games — and Steam itself —  is by getting a solid-state drive and installing Steam to it. Steam allows you to easily move your Steam folder — at C:\Program Files (x86)\Steam by default — to another hard drive. Just move it like you would any other folder. You can then launch the Steam.exe program as if you had never moved Steam’s files. Steam also allows you to configure multiple game library folders. This means that you can set up a Steam library folder on a solid-state drive and one on your larger magnetic hard drive. Install your most frequently played games to the solid-state drive for maximum speed and your less frequently played ones to the slower magnetic hard drive to save SSD space. To set up additional library folders, open Steam’s Settings window and click the Downloads tab. You’ll find the Steam Library Folders option here. Click the Add Library Folder button and create a new game library on another hard drive. When you install a game in Steam, you’ll be asked which library folder you want to install it to. With the proxy compatibility option disabled, the correct download server chosen, and Steam installed to a fast SSD, it should be a speed demon. There’s not much more you can do to speed up Steam, short of upgrading other hardware like your computer’s CPU. Image Credit: Andrew Nash on Flickr     

  Read the article

• BizTalk 2009 - Installing BizTalk Server 2009 on XP for Development

  - by StuartBrierley

  At my previous employer, when developing for BizTalk Server 2004 using Visual Studio 2003, we made use of separate development and deployment environments; developing in Visual Studio on our client PCs and then deploying to a seperate shared BizTalk 2004 Server from there.  This server was part of a multi-server Standard BizTalk environment comprising of separate BizTalk Server 2004 and SQL Server 2000 servers.  This environment was implemented a number of years ago by an outside consulting company, and while it worked it did occasionally cause contention issues with three developers deploying to the same server to carry out unit testing! Now that I am making the design and implementation decisions about the environment that BizTalk will be developed in and deployed to, I have chosen to create a single "server" installation on my development PC, installling SQL Server 2008, Visual Studio 2008 and BizTalk Server 2009 on a single system.  The client PC in use is actually a MacBook Pro running Windows XP; not the most powerful of systems for high volume processing but it should be powerful enough to allow development and initial unit testing to take place. I did not need to, and so chose not to, install all of the components detailed in the Microsoft guide for installing BizTalk 2009 on Windows XP but I did follow the basics of the procedures detailed within.  Outlined below are the highlights of this process and any details of what choices I made.   Install IIS I had previsouly installed Windows XP, including all current service packs and critical updates.  At the time of installation this included Service Pack 3, the .Net Framework 3.5 and MS Windows Installer 3.1.  Having a running XP system, my first step was to install IIS - this is quite straightforward and posed no difficulties. Install Visual Studio 2008 The next step for me was to install Visual Studio 2008.  Making sure to select a custom installation is crucial at this point, as you need to make sure that you deselect SQL Server 2005 Express Edition as it can cause the BizTalk installation to fail.  The installation guide suggests that you only select Visual C# when selecting features to install, but  I decided that due to some legacy systems I have code for that I would also select the VB and ASP options. Visual Studio 2008 Service Pack 1 Following the completion of the installation of Visual Studio itself you should then install the Visual Studio 2008 Service Pack 1. SQL Server 2008 Standard Edition The next step before intalling BizTalk Server 2009 itself is to install SQL Server 2008 Standard Edition. On the feature selection screen make sure that you select the follwoing options: Database Engine Services SQL Server Replication Full-Text Search Analysis Services Reporting Services Business Intelligence Development Studio Client Tools Connectivity Integration Services Management Tools Basic and Complete Use the default instance and the same accounts for all SQL server instances - in my case I used the Network Service and Local Service accounts for the two sets of accounts. On the database engine configuration screen I selected windows authentication and added the current user, adding the same user again on the Analysis services Configuration screen.  All other screens were left on the default settings. The SQL Server 2008 installation also included the installation of hotfix for XP KB942288-v3, the Windows Installer 4.5 Redistributable. System Configuration At this stage I took a moment to disable the SQL Server shared memory protocol and enable the Named Pipes and TCP/IP protocols.  These can be found in the SQL Server Configuration Manager > SQL Server Network Configuration > Protocols for MSSQLServer.  I also made sure that the DTC settings were configured correctley.   BizTalk Server 2009 The penultimate step is to install BizTalk Server 2009 Standard Edition. I had previsouly downloaded the redistributable prerequisites as a CAB file so was able to make use of this when carrying out the installation. When selecting which components to install I selected: Server Runtime BizTalk EDI/AS2 Runtime WCF Adapter Runtime Portal Components Administrative Tools WFC Administartion Tools Developer Tools and SDK, Enterprise SSO Administration Module Enterprise SSO Master Secret Server Business Rules Components BAM Alert Provider BAM Client BAM Eventing Once installation has completed clear the launch BizTalk Server Configuration check box and select finish. Verify the Installation Before configuring BizTalk Server it is a good idea to check that BizTalk Server 2009 is installed and that SQL Server 2008 has started correctly.  The easiest way to verify the BizTalk installation is check the Programs and Features in Control panel.  Check that SQL is started by looking in the SQL Server Configuration Manager. Configure BizTalk Server 2009 Finally we are ready to configure BizTalk Server 2009.  To start this I opted for a custom configuration that allowed me to choose in more detail the settings to be used. For all databases I selected the local server and default database names. For all Accounts I used a local account that had been created specifically for the BizTalk Services. For all windows groups I allowed the configuration wizard to create the default local groups. The configuration wizard then ran:   Upon completion you will be presented with a screen detailing the success or failure of the configuration.  If your configuration failed you will need to sort out the issues and try again (it is possible to save the configuration settings for later use if you want too - except passwords of course!).  If you see lots of nice green ticks - congratulations BizTalk Server 2009 on XP is now installed and configured ready for development.

  Read the article

• Identity R2 - Experts Podcast Series

  - by Tanu Sood

  To follow up on the Identity Management R2 launch, a series of podcasts were recorded with subject matter experts from customer organizations, our partners and Oracle’s PM team to discuss key trends, R2 capabilities, implementation best practices and more. Below is a roll-up of the podcast series that is available on Fusion Middleware radio. R2 Podcasts:   ·         Designing the Next-Generation Identity Platform Vadim Lander, Oracle Highlights: Common architecture model, integration, interoperability and the driving factors behind R2 innovation IT Departments are shifting their Identity Management strategy to be able to support mobile, cloud and social applications. Oracle has anticipated this shift and has built a product roadmap to take advantage of this focus. Join Vadim as he discusses the design strategy behind the latest 11gR2 release and talks about how IDM services have to evolve to meet this new challenge.   ·         BETA Customer Perspective on R2 Ravi Meduri, Kaiser Permanente Highlights: R2 scalability and high availability In this podcast Ravi discusses the new features in 11gR2 that he is most interested in, including High Availability options for Access Management, multi-datacenter architecture, and what it was like working with the Oracle product team during the BETA program.   ·         Partner Perspective on R2 Rex Thexton, PricewaterhouseCoopers Highlights: Usability Enhancements for Users and Administrators A lot of new usability features went into the 11gR2 release making this the most business friendly IDM release to date. In this podcast Rex Thexton, Managing Director from PwC, talks about some of the new UI changes for both end users and administrators, and also about the new connector creation framework.   Access Request Updates in R2 Marc Boroditsky, Oracle Highlights: Access request User Interface innovations A lot of changes have been made to the Access Request user interface in the latest version of Oracle Identity Manager 11gR2. A real focus has been put on making the request process more business user friendly, and a lot of new customization capability has been added for the IT administrators. Hear Marc discuss the updated UI, and explain how administrators will be able to customize OIM to meet their company's requirements   ·         Oracle Optimized System for Oracle Unified Directory (OOS4OUD) Nick Kloski, Oracle Highlights: New Optimized System configuration for Unified Directory One of the new features in 11gR2 is the availability of an Optimized System configuration for Oracle Unified Directory. Oracle engineers installed the OUD software onto off the shelf hardware and then created a performance tuned configuration. Join us as we talk to Nick Kloski, Infrastructure Solutions Manager, all about the testing process and the resulting performance metrics.   Privileged Account Management Mark Wilcox, Oracle Highlights: Oracle Privileged Account Manager key capabilities, use cases The new release of Oracle Identity Management 11g R2 includes the capability to manage privileged accounts. Privileged accounts, if compromised, create a risk for fraud in the enterprise and as a result controlling access to privileged accounts is critical. Hear what Mark Wilcox, Principal Product Manager of Oracle Privileged Account Manager has to say about the capabilities of the offering in this podcast.   ·         Browser-based User Interface (UI) Customization Clayton Donley, Oracle Highlights: Benefits of Durable UI Configuration framework Business users need user interfaces that are not only friendly but also easily customizable. However the downside of any customization project is the cost and complexity involved in developing, testing, deploying and managing custom code. In this podcast, we examine how a new capability in Oracle Identity Management around browser based UI customization can reduce costs and complexity of customization while simplifying self service integration with corporate portal strategies.   ·         Simplifying Mobile and Social Sign-On Dan Killmer, Oracle Highlights: Secure mobile sign-on and consumption of social identities with Oracle Access Management The proliferation of mobile devices has spurred a new trend where employees tend to bring their own mobile devices to work and access corporate applications the same way they would access from a desktop or laptop. In this podcast, we examine how Oracle's latest innovation in Identity Management around Mobile and Social Sign On can simplify security and access management challenges posed by the widespread adoption of mobile devices in the enterprise. ·         Enabling Your Business with IDM R2 Scott Bonnell, Oracle Highlights: Self service, mobile access, personalization Gone are the days when Identity Management was just about stopping unauthorized users in their tracks. Identity Management if done right, can also enable your business. Join Scott Bonnell as he discusses how the IDM 11gR2 release enables the enterprise by providing self service, personalization and mobile access to corporate resources.

  Read the article

< Previous Page | 248 249 250 251 252 253 254 255 256 257 258 259  | Next Page >