Search Results

Search found 15602 results on 625 pages for 'installation media'.

Page 252/625 | < Previous Page | 248 249 250 251 252 253 254 255 256 257 258 259  | Next Page >

• Can't add Fedora 14 to grub.

  - by Dananjaya

  Today I installed Fedora 14 in a different partition in the same hard drive as Ubuntu. At the Fedora 14 installation, I chose not to install Boot-loader in the MBR, and instead chose to install it in the Fedora partition itself, which is according to my HD layout /sda3. After the Fedora 14 installation I booted in to Ubuntu and ran sudo update-grub but 'grub.cfg' fails to add Fedora 14 in to the OS list. Here is the output of boot-info script. Boot Info Script 0.60 from 17 May 2011 ============================= Boot Info Summary: =============================== = Grub2 (v1.99) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos1)/boot/grub on this drive. sda1: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 11.04 Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sda2: __________________________________________________________________________ File system: Extended Partition Boot sector type: Unknown Boot sector info: sda5: __________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: sda3: __________________________________________________________________________ File system: ext4 Boot sector type: Grub Legacy Boot sector info: Grub Legacy (v0.97) is installed in the boot sector of sda3 and looks at sector 49897340 on boot drive #1 for the stage2 file. A stage2 file is at this location on /dev/sda. Stage2 looks on partition #3 for /grub/grub.conf. Operating System: Boot files: /grub/menu.lst /grub/grub.conf sda4: __________________________________________________________________________ File system: LVM2_member Boot sector type: - Boot sector info: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 40.0 GB, 40020664320 bytes 255 heads, 63 sectors/track, 4865 cylinders, total 78165360 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 * 2,048 49,865,759 49,863,712 83 Linux /dev/sda2 74,866,686 78,163,967 3,297,282 5 Extended /dev/sda5 74,866,688 78,163,967 3,297,280 82 Linux swap / Solaris /dev/sda3 49,866,752 50,890,751 1,024,000 83 Linux /dev/sda4 50,890,752 74,864,639 23,973,888 8e Linux LVM "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/sda1 03e2a8da-171f-49e9-b24d-434e66cd1140 ext4 /dev/sda3 dea81d77-a375-4d0e-954e-1829f6b91f10 ext4 /dev/sda4 mzVoj0-GHJu-DJr4-0G2Y-SzZ0-LTfW-F01yf9 LVM2_member /dev/sda5 3e89ba8e-7754-4ee4-aca1-e2a82bffb7a7 swap ================================ Mount points: ================================= Device Mount_Point Type Options /dev/sda1 / ext4 (rw,errors=remount-ro,user_xattr,commit=0) =========================== sda1/boot/grub/grub.cfg: =========================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="2" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=1024x768 load_video insmod gfxterm fi terminal_output gfxterm insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 2.6.38-8-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 linux /boot/vmlinuz-2.6.38-8-generic root=UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 ro quiet splash vt.handoff=7 initrd /boot/initrd.img-2.6.38-8-generic } menuentry 'Ubuntu, with Linux 2.6.38-8-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 echo 'Loading Linux 2.6.38-8-generic ...' linux /boot/vmlinuz-2.6.38-8-generic root=UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.38-8-generic } submenu "Previous Linux versions" { menuentry 'Ubuntu, with Linux 2.6.35-28-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 linux /boot/vmlinuz-2.6.35-28-generic root=UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 ro quiet splash vt.handoff=7 initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-28-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 echo 'Loading Linux 2.6.35-28-generic ...' linux /boot/vmlinuz-2.6.35-28-generic root=UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.32-21-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 linux /boot/vmlinuz-2.6.32-21-generic root=UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 ro quiet splash vt.handoff=7 initrd /boot/initrd.img-2.6.32-21-generic } menuentry 'Ubuntu, with Linux 2.6.32-21-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 echo 'Loading Linux 2.6.32-21-generic ...' linux /boot/vmlinuz-2.6.32-21-generic root=UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.32-21-generic } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### if [ "x${timeout}" != "x-1" ]; then if keystatus; then if keystatus --shift; then set timeout=-1 else set timeout=0 fi else if sleep --interruptible 3 ; then set timeout=0 fi fi fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### -------------------------------------------------------------------------------- =============================== sda1/etc/fstab: ================================ -------------------------------------------------------------------------------- # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda1 during installation # Commented out by Dropbox # UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=3e89ba8e-7754-4ee4-aca1-e2a82bffb7a7 none swap sw 0 0 UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 / ext4 errors=remount-ro,user_xattr 0 1 -------------------------------------------------------------------------------- =================== sda1: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) 0.065803528 = 0.070656000 boot/grub/core.img 1 21.263332367 = 22.831329280 boot/grub/grub.cfg 1 0.771381378 = 0.828264448 boot/initrd.img-2.6.31-wl 1 2.054199219 = 2.205679616 boot/initrd.img-2.6.32-21-generic 3 2.893260956 = 3.106615296 boot/initrd.img-2.6.35-28-generic 2 6.833232880 = 7.337127936 boot/initrd.img-2.6.38-8-generic 2 1.772453308 = 1.903157248 boot/vmlinuz-2.6.32-21-generic 2 2.068012238 = 2.220511232 boot/vmlinuz-2.6.35-28-generic 1 5.532531738 = 5.940510720 boot/vmlinuz-2.6.38-8-generic 1 6.833232880 = 7.337127936 initrd.img 2 2.893260956 = 3.106615296 initrd.img.old 2 5.532531738 = 5.940510720 vmlinuz 1 2.068012238 = 2.220511232 vmlinuz.old 1 ============================= sda3/grub/grub.conf: ============================= -------------------------------------------------------------------------------- # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,2) # kernel /vmlinuz-version ro root=/dev/mapper/VolGroup-lv_root # initrd /initrd-[generic-]version.img #boot=/dev/sda3 default=0 timeout=0 splashimage=(hd0,2)/grub/splash.xpm.gz hiddenmenu title Fedora (2.6.35.6-45.fc14.i686) root (hd0,2) kernel /vmlinuz-2.6.35.6-45.fc14.i686 ro root=/dev/mapper/VolGroup-lv_root rd_LVM_LV=VolGroup/lv_root rd_LVM_LV=VolGroup/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet initrd /initramfs-2.6.35.6-45.fc14.i686.img -------------------------------------------------------------------------------- =================== sda3: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) 23.792903900 = 25.547436032 grub/grub.conf 1 23.792903900 = 25.547436032 grub/menu.lst 1 23.793020248 = 25.547560960 grub/stage2 1 23.817364693 = 25.573700608 initramfs-2.6.35.6-45.fc14.i686.img 2 23.787566185 = 25.541704704 initrd-plymouth.img 1 23.791228294 = 25.545636864 vmlinuz-2.6.35.6-45.fc14.i686 1 ======================== Unknown MBRs/Boot Sectors/etc: ======================== Unknown BootLoader on sda2 00000000 81 71 62 ff a1 94 89 ff 4d 43 3a ff fa f2 ec ff |.qb.....MC:.....| 00000010 fb f6 f1 ff fc f8 f4 ff fc f8 f4 ff fc f8 f4 ff |................| 00000020 5d 56 50 ff a1 94 89 ff 81 70 62 ff 81 70 62 ff |]VP......pb..pb.| 00000030 81 70 62 ff 81 70 62 ff 81 70 62 ff a1 94 89 ff |.pb..pb..pb.....| 00000040 4d 43 3a ff fa f2 ec ff fb f6 f1 ff fc f8 f4 ff |MC:.............| 00000050 fc f8 f4 ff fc f8 f4 ff 5d 56 50 ff a1 94 89 ff |........]VP.....| 00000060 81 70 62 ff 81 70 62 ff 81 70 62 ff 81 70 62 ff |.pb..pb..pb..pb.| 00000070 81 70 62 ff a1 94 89 ff 4d 43 3a ff fa f2 ec ff |.pb.....MC:.....| 00000080 fb f6 f1 ff fc f8 f4 ff fc f8 f4 ff fc f8 f4 ff |................| 00000090 5d 56 50 ff a0 93 89 ff 80 6f 61 ff 80 6f 61 ff |]VP......oa..oa.| 000000a0 80 6f 61 ff 80 6f 61 ff 80 6f 61 ff a0 93 89 ff |.oa..oa..oa.....| 000000b0 4d 43 3a ff fa f2 ed ff fb f6 f2 ff fc f8 f5 ff |MC:.............| 000000c0 fc f8 f5 ff fc f8 f5 ff 5d 56 50 ff 9f 93 88 ff |........]VP.....| 000000d0 7f 6f 60 ff 7f 6f 60 ff 7f 6f 60 ff 7f 6f 60 ff |.o`..o`..o`..o`.| 000000e0 7f 6f 60 ff 9f 93 88 ff 4d 43 3a ff fa f2 ed ff |.o`.....MC:.....| 000000f0 fb f6 f2 ff fc f8 f5 ff fc f8 f5 ff fc f8 f5 ff |................| 00000100 5d 56 50 ff 9f 93 88 ff 7f 6f 60 ff 7f 6f 60 ff |]VP......o`..o`.| 00000110 7f 6f 60 ff 7f 6f 60 ff 7f 6f 60 ff 9f 93 88 ff |.o`..o`..o`.....| 00000120 4d 43 3a ff fa f2 ed ff fb f6 f2 ff fc f8 f5 ff |MC:.............| 00000130 fc f8 f5 ff fc f8 f5 ff 5d 56 50 ff 9e 92 88 ff |........]VP.....| 00000140 7e 6e 60 ff 7e 6e 60 ff 7e 6e 60 ff 7e 6e 60 ff |~n`.~n`.~n`.~n`.| 00000150 7e 6e 60 ff 9e 92 88 ff 4d 43 3a ff fa f2 ed ff |~n`.....MC:.....| 00000160 fb f6 f2 ff fc f8 f5 ff fc f8 f5 ff fc f8 f5 ff |................| 00000170 5d 56 50 ff 9e 92 88 ff 7d 6d 5f ff 7d 6d 5f ff |]VP.....}m_.}m_.| 00000180 7d 6d 5f ff 7d 6d 5f ff 7d 6d 5f ff 9e 92 88 ff |}m_.}m_.}m_.....| 00000190 4d 43 3a ff fa f2 ed ff fb f6 f2 ff fc f8 f5 ff |MC:.............| 000001a0 fc f8 f5 ff fc f8 f5 ff 5d 56 50 ff 9e 92 88 ff |........]VP.....| 000001b0 7d 6d 5f ff 7d 6d 5f ff 7d 6d 5f ff 7d 6d 00 fe |}m_.}m_.}m_.}m..| 000001c0 ff ff 82 fe ff ff 02 00 00 00 00 50 32 00 00 00 |...........P2...| 000001d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 000001f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa |..............U.| 00000200 =============================== StdErr Messages: =============================== unlzma: Decoder error According to this Fedora 14 is visible in sda3. Does anybody know a way to add Fedora 14 to grub.cfg of Ubuntu so I can choose which OS to boot? Thanks in advance.

  Read the article

• Summary of Oracle E-Business Suite Technology Webcasts and Training

  - by BillSawyer

  Last Updated: November 16, 2011We're glad to hear that you've been finding our ATG Live Webcast series to be useful.  If you missed a webcast, you can download the presentation materials and listen to the recordings below. We're collecting other learning-related materials right now.  We'll update this summary with pointers to new training resources on an ongoing basis.  ATG Live Webcast Replays All of the ATG Live Webcasts are hosted by the Oracle University Knowledge Center.  In order to access the replays, you will need a free Oracle.com account. You can register for an Oracle.com account here.If you are a first-time OUKC user, you will have to accept the Terms of Use. Sign-in with your Oracle.com account, or if you don't already have one, use the link provided on the sign-in screen to create an account. After signing in, accept the Terms of Use. Upon completion of these steps, you will be directed to the replay. You only need to accept the Terms of Use once. Your acceptance will be noted on your account for all future OUKC replays and event registrations. 1. E-Business Suite R12 Oracle Application Framework (OAF) Rich User Interface Enhancements (Presentation) Prabodh Ambale (Senior Manager, ATG Development) and Gustavo Jiminez (Development Manager, ATG Development) offer a comprehensive review of the latest user interface enhancements and updates to OA Framework in EBS 12.  The webcast provides a detailed look at new features designed to enhance usability, including new capabilities for personalization and extensions, and features that support the use of dashboards and web services. (January 2011) 2. E-Business Suite R12 Service Oriented Architectures (SOA) Using the E-Business Suite Adapter (Presentation, Viewlet) Neeraj Chauhan (Product Manager, ATG Development) reviews the Service Oriented Architecture (SOA) capabilities within E-Business Suite 12, focussing on using the E-Business Suite Adapter to integrate EBS with third-party applications via web services, and orchestrate services and distributed transactions across disparate applications. (February 2011) 3. Deploying Oracle VM Templates for Oracle E-Business Suite and Oracle PeopleSoft Enterprise Applications Ivo Dujmovic (Director, ATG Development) reviews the latest capabilities for using Oracle VM to deploy virtualized EBS database and application tier instances using prebuilt EBS templates, wire those virtualized instances together using the EBS virtualization kit, and take advantage of live migration of user sessions between failing application tier nodes.  (February 2011) 4. How to Reduce Total Cost of Ownership (TCO) Using Oracle E-Business Suite Management Packs (Presentation) Angelo Rosado (Product Manager, ATG Development) provides an overview of how EBS sysadmins can make their lives easier with the Management Packs for Oracle E-Business Suite Release 12.  This session highlights key features in Application Management Pack (AMP) and Application Change Management Pack) that can automate or streamline system configurations, monitor EBS performance and uptime, keep multiple EBS environments in sync with patches and configurations, and create patches for your own EBS customizations and apply them with Oracle's own patching tools.  (June 2011) 5. Upgrading E-Business Suite 11i Customizations to R12 (Presentation) Sara Woodhull (Principal Product Manager, ATG Development) provides an overview of how E-Business Suite developers can manage and upgrade existing EBS 11i customizations to R12.  Sara covers methods for comparing customizations between Release 11i and 12, managing common customization types, managing deprecated technologies, and more. (July 2011) 6. Tuning All Layers of E-Business Suite (Part 1 of 3) (Presentation) Lester Gutierrez, Senior Architect, and Deepak Bhatnagar, Senior Manager, from the E-Business Suite Application Performance team, lead Tuning All Layers of E-Business Suite (Part 1 of 3). This webcast provides an overview of how Oracle E-Business Suite system administrators, DBAs, developers, and implementers can improve E-Business Suite performance by following a performance tuning framework. Part 1 focuses on the performance triage approach, tuning applications modules, upgrade performance best practices, and tuning the database tier. This ATG Live Webcast is an expansion of the performance sessions at conferences that are perennial favourites with hardcore Apps DBAs. (August 2011)  7. Oracle E-Business Suite Directions: Deployment and System Administration (Presentation) Max Arderius, Manager Applications Technology Group, and Ivo Dujmovic, Director Applications Technology group, lead Oracle E-Business Suite Directions: Deployment and System Administration covering important changes in E-Business Suite R12.2. The changes discussed in this presentation include Oracle E-Business Suite architecture, installation, upgrade, WebLogic Server integration, online patching, and cloning. This webcast provides an overview of how Oracle E-Business Suite system administrators, DBAs, developers, and implementers can prepare themselves for these changes in R12.2 of Oracle E-Business Suite. (October 2011) Oracle University Courses For a general listing of all Oracle University courses related to E-Business Suite Technology, use the Oracle University E-Business Suite Technology course catalog link. Oracle University E-Business Suite Technology Course Catalog 1. R12 Oracle Applications System Administrator Fundamentals In this course students learn concepts and functions that are critical to the System Administrator role in implementing and managing the Oracle E-Business Suite. Topics covered include configuring security and user management, configuring flexfields, managing concurrent processing, and setting up other essential features such as profile options and printing. In addition, configuration and maintenance of an Oracle E-Business Suite through Oracle Applications Manager is discussed. Students also learn the fundamentals of Oracle Workflow including its setup. The System Administrator Fundamentals course provides the foundation needed to effectively control security and ensure smooth operations for an E-Business Suite installation. Demonstrations and hands-on practice reinforce the fundamental concepts of configuring an Oracle E-Business Suite, as well as handling day-to-day system administrator tasks. 2. R12.x Install/Patch/Maintain Oracle E-Business Suite This course will be applicable for customers who have implemented Oracle E-Business Suite Release 12 or Oracle E-Business Suite 12.1. This course explains how to go about installing and maintaining an Oracle E-Business Suite Release 12.x system. Both Standard and Express installation types are covered in detail. Maintenance topics include a detailed examination of the standard tools and utilities, and an in-depth look at patching an Oracle E-Business Suite system. After this course, students will be able to make informed decisions about how to install an Oracle E-Business Suite system that meets their specific requirements, and how to maintain the system afterwards. The extensive hands-on practices include performing an installation on a Linux system, navigating the file system to locate key files, running the standard maintenance tools and utilities, applying patches, and carrying out cloning operations. 3. R12.x Extend Oracle Applications: Building OA Framework Applications This class is a hands-on lab-intensive course that will keep the student busy and active for the duration of the course. While the course covers the fundamentals that support OA Framework-based applications, the course is really an exercise in J2EE programming. Over the duration of the course, the student will create an OA Framework-based application that selects, inserts, updates, and deletes data from a R12 Oracle Applications instance. 4. R12.x Extend Oracle Applications: Customizing OA Framework Applications This course has been significantly changed from the prior version to include additional deployments. The course doesn't teach the specifics of configuration of each product. That is left to the product-specific courses. What the course does cover is the general methods of building, personalizing, and extending OA Framework-based pages within the E-Business Suite. Additionally, the course covers the methods to deploy those types of customizations. The course doesn't include discussion of the Oracle Forms-based pages within the E-Business Suite. 5. R12.x Extend Oracle Applications: OA Framework Personalizations Personalization is the ability within an E-Business Suite instance to make changes to the look and behavior of OA Framework-based pages without programming. And, personalizations are likely to survive patches and upgrades, increasing their utility. This course will systematically walk you through the myriad of personalization options, starting with simple examples and increasing in complexity from there. 6. E-Business Suite: BI Publisher 5.6.3 for Developers Starting with the basic concepts, architecture, and underlying standards of Oracle XML Publisher, this course will lead a student through a progress of exercises building their expertise. By the end of the course, the student should be able to create Oracle XML Publisher RTF templates and data templates. They should also be able to deploy and maintain a BI Publisher report in an E-Business Suite instance. Students will also be introduced to Oracle BI Publisher Enterprise. 7. R12.x Implement Oracle Workflow This course provides an overview of the architecture and features of Oracle Workflow and the benefits of using Oracle Workflow in an e-business environment. You can learn how to design workflow processes to automate and streamline business processes, and how to define event subscriptions to perform processing triggered by business events. Students also learn how to respond to workflow notifications, how to administer and monitor workflow processes, and what setup steps are required for Oracle Workflow. Demonstrations and hands-on practice reinforce the fundamental concepts. 8. R12.x Oracle E-Business Suite Essentials for Implementers Oracle R12.1 E-Business Essentials for Implementers is a course that provides a functional foundation for any E-Business Suite Fundamentals course.

  Read the article

• SQL – NuoDB and Third Party Explorer – SQuirreL SQL Client, SQL Workbench/J and DbVisualizer

  - by Pinal Dave

  I recently wrote a four-part series on how I started to learn about and begin my journey with NuoDB. Big Data is indeed a big world and the learning of the Big Data is like spaghetti – no one knows in reality where to start, so I decided to learn it with the help of NuoDB. You can download NuoDB and continue your journey with me as well. Part 1 – Install NuoDB in 90 Seconds Part 2 – Manage NuoDB Installation Part 3 – Explore NuoDB Database Part 4 – Migrate from SQL Server to NuoDB …and in this blog post we will try to answer the most asked question about NuoDB. “I like the NuoDB Explorer but can I connect to NuoDB from my preferred Graphical User Interface?” Honestly, I did not expect this question to be asked of me so many times but from the question it is clear that we developers absolutely want to learn new things and along with that we do want to continue to use our most efficient developer tools. Now here is the answer to the question: “Absolutely, you can continue to use any of the following most popular SQL clients.” NuoDB supports the three most popular 3rd-party SQL clients. In all the leading development environments there are always more than one database installed and managing each of them with a different tool is often a very difficult task. Developers like to use one tool, which can control most of the databases. Once developers are familiar with one database tool it is very difficult for them to switch to another tool. This is particularly difficult when we developers find that tool to be the key reason for our efficiency. Let us see how to install each of the NuoDB supported 3rd party tools along with a quick tutorial on how to go about using them. SQuirreL SQL Client First download SQuirreL Universal SQL client. On the Windows platform you can double-click on the file and it will install the SQuirrel client. Once it is installed, open the application and it will bring up the following screen. Now go to the Drivers tab on the left side and scroll it down. You will find NuoDB mentioned there. Now right click over it and click on Modify Driver. Now here is where you need to make sure that you make proper entries or your client will not work with the database. Enter following values: Name: NuoDB Example URL: jdbc:com:nuodb://localhost:48004/test Website URL: http://www.nuodb.com Now click on the Extra Class Path tab and Add the location of the nuodbjdbc.jar file. If you are following my blog posts and have installed NuoDB in the default location, you will find the default path as C:\Program Files\NuoDB\jar\nuodbjdbc.jar. The class name of the driver is automatically populated. Once you click OK you will see that there is a small icon displayed to the left of NuoDB, which shows that you have successfully configured and installed the NuoDB driver. Now click on the tab of Alias tab and you can notice that it is empty. Now click on the big Plus icon and it will open screen of adding an alias. “Alias” means nothing more than adding a database to your system. The database name of the original installation can be anything and, if you wish, you can register the database with any other alternative name. Here are the details you should fill into the Alias screen below. Name: Test (or your preferred alias) Driver: NuoDB URL: jdbc:com:nuodb://localhost:48004/test (This is for test database) User Name: dba (This is the username which I entered for test Database) Password: goalie (This is the password which I entered for test Database) Check Auto Logon and Connect at Startup and click on OK. That’s it! You are done. On the right side you will see a table name and on the left side you will see various tabs with all the relevant details from respective table. You can see various metadata, schemas, data types and other information in the table. In addition, you can also generate script and do various important tasks related to database. You can see how easy it is to configure NuoDB with the SQuirreL Client and get going with it immediately. SQL Workbench/J This is another wonderful client tool, which works very well with NuoDB. The best part is that in the Driver dropdown you will see NuoDB being mentioned there. Click here to download  SQL Workbench/J Universal SQL client. The download process is straight forward and the installation is a very easy process for SQL Workbench/J. As soon as you open the client, you will notice on following screen the NuoDB driver when selecting a New Connection Profile. Select NuoDB from the drop down and click on OK. In the driver information, enter following details: Driver: NuoDB (com.nuodb.jdbc.Driver) URL: jdbc:com.nuodb://localhost/test Username: dba Password: goalie While clicking on OK, it will bring up the following pop-up. Click Yes to edit the driver information. Click on OK and it will bring you to following screen. This is the screen where you can perform various tasks. You can write any SQL query you want and it will instantly show you the results. Now click on the database icon, which you see right on the left side of the word User=dba.  Once you click on Database Explorer, you can perform various database related tasks. As a developer, one of my favorite tasks is to look at the source of the table as it gives me a proper view of the structure of the database. I find SQL Workbench/J very efficient in doing the same. DbVisualizer DBVisualizer is another great tool, which helps you to connect to NuoDB and retrieve database information in your desired format. A developer who is familiar with DBVisualizer will find this client to be very easy to work with. The installation of the DBVisualizer is very pretty straight forward. When we open the client, it will bring us to the following screen. As a first step we need to set up the driver. Go to Tools >> Driver Manager. It will bring up following screen where we set up the diver. Click on Create Driver and it will open up the driver settings on the right side. On the right side of the area where it displays Driver Settings please enter the following values- Name: NuoDB URL Format: jdbc:com.nuodb://localhost:48004/test Now under the driver path, click on the folder icon and it will ask for the location of the jar file. Provide the path as a C:\Program Files\NuoDB\jar\nuodbjdbc.jar and click OK. You will notice there is a green button displayed at the bottom right corner. This means the driver is configured properly. Once driver is configured properly, we can go to Create Database Connection and create a database. If the pop up show up for the Wizard. Click on No Wizard and continue to enter the settings manually. Here is the Database Connection screen. This screen can be bit tricky. Here are the settings you need to remember to enter. Name: NuoDB Database Type: Generic Driver: NuoDB Database URL: jdbc:com.nuodb://localhost:48004/test Database Userid: dba Database Password: goalie Once you enter the values, click on Connect. Once Connect is pressed, it will change the button value to Reconnect if the connection is successfully established and it will show the connection details on lthe eft side. When we further explore the NuoDB, we can see various tables created in our test application. We can further click on the right side screen and see various details on the table. If you click on the Data Tab, it will display the entire data of the table. The Tools menu also has some very interesting and cool features like Driver Manager, Data Monitor and SQL History. Summary Well, this was a relatively long post but I find it is extremely essential to cover all the three important clients, which we developers use in our daily database development. Here is my question to you? Which one of the following is your favorite NuoDB 3rd-Party Database Client? (Pick One) SQuirreL SQL Client SQL Workbench/J DbVisualizer I will be very much eager to read your experience about NuoDB. You can download NuoDB from here. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Big Data, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology Tagged: NuoDB

  Read the article

• Unity stuck in 2D mode, Nvidia Quadro graphics "unknown", Nvidia-Current active but not in use

  - by Jordan Lund

  I've seen this problem reported under several questions, but I haven't been able to resolve any of it so I thought I'd bring it all in under one umbrella. I started a new job and was given a Dell Precision M6400 laptop with Nvidia Quadro FX 2700M graphics card. It had a previous version of Ubuntu on it, but nobody had any passwords for it so I wiped the drive and did a fresh install of 11.10 from scratch. I didn't do any updates during installation, preferring to do them after boot. Updates ran fine and the system works... except Unity is in 2D mode. System Settings - Additional Drivers shows that Nvidia-Current is active but not in use. System Settings - System Info shows Graphics Driver Unknown, Experience Standard Nvidia X Server Settings is installed and working, re-writing the xorg.conf did nothing. /usr/lib/nux/unity_support_test -p OpenGL vendor string: NVIDIA Corporation OpenGL renderer string: Quadro FX 2700M/PCI/SSE2 OpenGL version string: 3.3.0 NVIDIA 285.05.09 Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: yes One suggestion was to do a sudo apt-get --purge remove nvidia* and that resulted in a scrambled screen on boot and a non-bootable installation. Pressing the Delete key on boot allowed me to access the recovery console and do a sudo apt-get install nvidia-current, which brought me back to a working, bootable system. Another suggestion was to edit /etc/default/grub and change the line reading "GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" to read "GRUB_CMDLINE_LINUX_DEFAULT="quiet splash vmalloc=192MB" thus allocating more video RAM. I did that, followed by a sudo update-grub and a re-boot. No change. Created a brand new standard user and logged on with that account, no change.

  Read the article

• Unable to uninstall maas completely

  - by user210844

  I'm not able to uninstall MAAS sudo apt-get purge maas ; sudo apt-get autoremove Reading package lists... Done Building dependency tree Reading state information... Done Package 'maas' is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 2 not upgraded. 2 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up maas-region-controller (1.2+bzr1373+dfsg-0ubuntu1) ... Considering dependency proxy for proxy_http: Module proxy already enabled Module proxy_http already enabled Module expires already enabled Module wsgi already enabled sed: -e expression #1, char 91: unterminated `s' command dpkg: error processing maas-region-controller (--configure): subprocess installed post-installation script returned error exit status 1 No apport report written because MaxReports is reached already dpkg: dependency problems prevent configuration of maas-dns: maas-dns depends on maas-region-controller (= 1.2+bzr1373+dfsg-0ubuntu1); however: Package maas-region-controller is not configured yet. dpkg: error processing maas-dns (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already Errors were encountered while processing: maas-region-controller maas-dns E: Sub-process /usr/bin/dpkg returned an error code (1) Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 2 not upgraded. 2 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up maas-region-controller (1.2+bzr1373+dfsg-0ubuntu1) ... Considering dependency proxy for proxy_http: Module proxy already enabled Module proxy_http already enabled Module expires already enabled Module wsgi already enabled sed: -e expression #1, char 91: unterminated `s' command dpkg: error processing maas-region-controller (--configure): subprocess installed post-installation script returned error exit status 1 No apport report written because MaxReports is reached already dpkg: dependency problems prevent configuration of maas-dns: maas-dns depends on maas-region-controller (= 1.2+bzr1373+dfsg-0ubuntu1); however: Package maas-region-controller is not configured yet. dpkg: error processing maas-dns (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already Errors were encountered while processing: maas-region-controller maas-dns E: Sub-process /usr/bin/dpkg returned an error code (1)

  Read the article

• Windows CE: SDK Doesn’t Show up in Visual Studio 2008

  - by Bruce Eitman

  A customer recently contacted me because after installing an SDK it didn’t show up in Visual Studio 2008.  So being a good vendor I installed VS2008 and then installed the SDK – no problem the SDK showed up and I could create projects based on it. I let the customer know that the SDK definitely works with VS2008. The customer got back to me and asked what OS I was using. Hmm, how could that play into this? I told him that I use Windows XP, and it turned out that he is way more modern than I am and is using both Windows Vista and 7. The customer opened a support case with Microsoft. The answer turns out to be that the SDK install requires the user to be logged on as an administrator when installing on Windows Vista and 7 for the SDK to show up in Visual Studio 2008. This problem does not seem to exist for Visual Studio 2005 on those operating systems. The actual instructions from Microsoft Support are: 1)      Make sure Visual Studio 2008 is not running. I also shut down the device emulator manager but you may not be using that. 2)      Open a “Visual Studio 2008 Command Prompt” as Administrator. On Windows 7 just right click the short cut and pick the “Run as administrator” option. 3)      Enter the following command: msiexec /log SDKInstallLog.txt /package <the path to your .msi file> 4)      When asked if you wish to do a custom or complete install pick custom 5)      Instruct the installer to omit the installation of the documentation. This was something I found about CE 6 SDK installation issue and may have no bearing upon your problem but I did it anyway. 6)      Install   Copyright © 2010 – Bruce Eitman All Rights Reserved

  Read the article

• Why does my PowerBook display “Fixing recursive fault but reboot is needed!” and stop booting?

  - by Blacklight Shining

  I have an old PowerBook G4 that worked (more or less) fine with a previous installation of Ubuntu Desktop 12.04. A few days ago I decided to install Ubuntu Server instead, and got a copy of Ubuntu Server 12.10. The installation seemed to complete successfully, but now, whenever I try to boot the system, it simply halts at some point after I unlock the hard disk. There is a lot of text on the screen (which is normal for me during a boot, except now it's mostly errors and debug information), the last of which is this: [ 26.338228] Fixing recursive fault but reboot is needed! Pressing control command power to force a reboot yields exactly the same results. A search for the error message turned up many temporary solutions involving kernel parameters, but none of them have worked for me. I don't think I can remove the default set of parameters (which I think is quiet splash), but I can pass additional parameters on boot. I've tried booting on AC and battery power, as well as using these combinations of kernel parameters while on battery power: acpi=enable pci=noacpi pci=assign-busse acpi=ht acpi=off nomodeset nomodeset acpi=off Why am I getting this error and how can I fix it?

  Read the article

• Can't install TeamViewer on Ubuntu 12.04

  - by Roel

  I have a Dell Inspiron 6400 laptop. I was a Windows user but I want to start using Ubuntu from now on. Everything goes well except installation of the teamviewer. I have downloaded the file from the official website. There, it says that just double click on the *.deb file and it will install it automatically. Well, it gives an error: Failed to remove essential system package, You requested to remove a package which is an essential part of your system. Then I tried the second way of installation, which is on the terminal. I types as suggested: sudo dpkg -i teamviewer_linux.deb. It started installing but later on failed. HEre is the copy of the screen. Preparing to replace teamviewer7:i386 7.0.9377 (using teamviewer_linux.deb) ... Unpacking replacement teamviewer7:i386 ... dpkg: dependency problems prevent configuration of teamviewer7:i386: teamviewer7:i386 depends on bash (>= 3.0). teamviewer7:i386 depends on libc6 (>= 2.7). teamviewer7:i386 depends on libasound2. teamviewer7:i386 depends on zlib1g. teamviewer7:i386 depends on libxext6. dpkg: error processing teamviewer7:i386 (--install): dependency problems - leaving unconfigured Errors were encountered while processing: teamviewer7:i386 I have already checked these dependent files in Synaptic and they are all installed. What am I doing wrong?

  Read the article

• Oracle VM Templates Available for E-Business Suite 12.1.3

  - by Steven Chan (Oracle Development)

  Oracle VM has matured into a formidable virtualization product over the years. Oracle E-Business Suite is certified to run production instances on both Oracle VM 2 and 3. This applies to EBS Releases 11i and 12.  It also applies to future Oracle VM 3 updates, including subsequent Oracle VM 3.x releases. E-Business Suite 12.1.3 Oracle VM templates available now The latest EBS 12.1.3 templates for Oracle VM can be downloaded here: Oracle VM Templates: E-Business Suite Templates are available for: E-Business Suite 12.1.3 Vision (64-bit) E-Business Suite 12.1.3 Production (32-bit) E-Business Suite 12.x Sparse Middle Tiers (32-bit and 64-bit) Should EBS 11i users care? Yes.  You can use these templates to get an EBS 12 testbed environment running in minutes.  This is a great way of giving your end-users a chance to work with EBS 12 without the overhead of building an environment from scratch. References Oracle VM 3 supports a number of guest operating systems including various flavors and versions of Linux, Solaris and Windows. For information regarding certified platforms, installation and upgrade guidance and prerequisite requirements please refer to the Certifications tab on My Oracle Support as well as the following documentation: Oracle VM Installation and Upgrade Guide  Introduction to Oracle VM, Oracle VM Manager and EBS template deployment (Note 1355641.1) Related Articles Oracle VM 3 Certified with Oracle E-Business Suite Support Policies for Virtualization Technologies and Oracle E-Business Suite The Scoop: Oracle E-Business Suite Support on 64-bit Linux

  Read the article

• MVVM Light V3 released at #MIX10

  - by Laurent Bugnion

  During my session “Understanding the MVVM pattern” at MIX10 in Vegas, I showed some components of the MVVM Light toolkit V3, which gave me the occasion to announce the release of version 3. This version has been in alpha stage for a while, and has been tested by many users. it is very stable, and ready for a release. So here we go! What’s new What’s new in MVVM Light Toolkit V3 is the topic of the next post. Cleaning up I would recommend cleaning up older versions before installing V3. I prepared a page explaining how to do that manually. Unfortunately I didn’t have time to create an automatic cleaner/installer, this is very high on my list but with the book and the conferences going on, it will take a little more time. Cleaning up is recommended because I changed the name of some DLLs to avoid some confusion (between the WPF3.5 and WPF4 version, as well as between the SL3 and SL4 versions). More details in the section titled “Compatibility”. Installation Installing MVVM Light toolkit is the manual process of unzipping a few files. The installation page has been updated to reflect the newest information. Compatibility MVVM Light toolkit V3 has components for the following environments and frameworks: Visual Studio 2008: Silverlight 3 Windows Presentation Foundation 3.5 SP1 Expression Blend 3 Silverlight 3 Windows Presentation Foundation 3.5 SP1 Visual Studio 2010 RC Silverlight 3 Silverlight 4 Windows Presentation Foundation 3.5 SP1 Windows Presentation Foundation 4 Silverlight for Windows Phone 7 series Expression Blend 4 beta Silverlight 3 Silverlight 4 Windows Presentation Foundation 3.5 SP1 Windows Presentation Foundation 4 Feedback As usual I welcome your constructive feedback. If you want the issue to be discussed in public, the best way is through the discussion page on the Codeplex site. if you wish to keep the conversation private, please check my Contact page for ways to talk to me. Video, tutorials There are a few new videos and tutorials available for the MVVM Light toolkit. The material is listed on the Get Started page, under “tutorials”.   Laurent Bugnion (GalaSoft) Subscribe | Twitter | Facebook | Flickr | LinkedIn

  Read the article

• JMS Step 3 - Using the QueueReceive.java Sample Program to Read a Message from a JMS Queue

  - by John-Brown.Evans

  JMS Step 3 - Using the QueueReceive.java Sample Program to Read a Message from a JMS Queue ol{margin:0;padding:0} .c18_3{vertical-align:top;width:487.3pt;border-style:solid;background-color:#f3f3f3;border-color:#000000;border-width:1pt;padding:0pt 5pt 0pt 5pt} .c20_3{vertical-align:top;width:487.3pt;border-style:solid;border-color:#ffffff;border-width:1pt;padding:5pt 5pt 5pt 5pt} .c19_3{background-color:#ffffff} .c17_3{list-style-type:circle;margin:0;padding:0} .c12_3{list-style-type:disc;margin:0;padding:0} .c6_3{font-style:italic;font-weight:bold} .c10_3{color:inherit;text-decoration:inherit} .c1_3{font-size:10pt;font-family:"Courier New"} .c2_3{line-height:1.0;direction:ltr} .c9_3{padding-left:0pt;margin-left:72pt} .c15_3{padding-left:0pt;margin-left:36pt} .c3_3{color:#1155cc;text-decoration:underline} .c5_3{height:11pt} .c14_3{border-collapse:collapse} .c7_3{font-family:"Courier New"} .c0_3{background-color:#ffff00} .c16_3{font-size:18pt} .c8_3{font-weight:bold} .c11_3{font-size:24pt} .c13_3{font-style:italic} .c4_3{direction:ltr} .title{padding-top:24pt;line-height:1.15;text-align:left;color:#000000;font-size:36pt;font-family:"Arial";font-weight:bold;padding-bottom:6pt}.subtitle{padding-top:18pt;line-height:1.15;text-align:left;color:#666666;font-style:italic;font-size:24pt;font-family:"Georgia";padding-bottom:4pt} li{color:#000000;font-size:10pt;font-family:"Arial"} p{color:#000000;font-size:10pt;margin:0;font-family:"Arial"} h1{padding-top:0pt;line-height:1.15;text-align:left;color:#888;font-size:24pt;font-family:"Arial";font-weight:normal} h2{padding-top:0pt;line-height:1.15;text-align:left;color:#888;font-size:18pt;font-family:"Arial";font-weight:normal} h3{padding-top:0pt;line-height:1.15;text-align:left;color:#888;font-size:14pt;font-family:"Arial";font-weight:normal} h4{padding-top:0pt;line-height:1.15;text-align:left;color:#888;font-size:12pt;font-family:"Arial";font-weight:normal} h5{padding-top:0pt;line-height:1.15;text-align:left;color:#888;font-size:11pt;font-family:"Arial";font-weight:normal} h6{padding-top:0pt;line-height:1.15;text-align:left;color:#888;font-size:10pt;font-family:"Arial";font-weight:normal} This post continues the series of JMS articles which demonstrate how to use JMS queues in a SOA context. In the first post, JMS Step 1 - How to Create a Simple JMS Queue in Weblogic Server 11g we looked at how to create a JMS queue and its dependent objects in WebLogic Server. In the previous post, JMS Step 2 - Using the QueueSend.java Sample Program to Send a Message to a JMS Queue I showed how to write a message to that JMS queue using the QueueSend.java sample program. In this article, we will use a similar sample, the QueueReceive.java program to read the message from that queue. Please review the previous posts if you have not already done so, as they contain prerequisites for executing the sample in this article. 1. Source code The following java code will be used to read the message(s) from the JMS queue. As with the previous example, it is based on a sample program shipped with the WebLogic Server installation. The sample is not installed by default, but needs to be installed manually using the WebLogic Server Custom Installation option, together with many, other useful samples. You can either copy-paste the following code into your editor, or install all the samples. The knowledge base article in My Oracle Support: How To Install WebLogic Server and JMS Samples in WLS 10.3.x (Doc ID 1499719.1) describes how to install the samples. QueueReceive.java package examples.jms.queue; import java.util.Hashtable; import javax.jms.*; import javax.naming.Context; import javax.naming.InitialContext; import javax.naming.NamingException; /** * This example shows how to establish a connection to * and receive messages from a JMS queue. The classes in this * package operate on the same JMS queue. Run the classes together to * witness messages being sent and received, and to browse the queue * for messages. This class is used to receive and remove messages * from the queue. * * @author Copyright (c) 1999-2005 by BEA Systems, Inc. All Rights Reserved. */ public class QueueReceive implements MessageListener { // Defines the JNDI context factory. public final static String JNDI_FACTORY="weblogic.jndi.WLInitialContextFactory"; // Defines the JMS connection factory for the queue. public final static String JMS_FACTORY="jms/TestConnectionFactory"; // Defines the queue. public final static String QUEUE="jms/TestJMSQueue"; private QueueConnectionFactory qconFactory; private QueueConnection qcon; private QueueSession qsession; private QueueReceiver qreceiver; private Queue queue; private boolean quit = false; /** * Message listener interface. * @param msg message */ public void onMessage(Message msg) { try { String msgText; if (msg instanceof TextMessage) { msgText = ((TextMessage)msg).getText(); } else { msgText = msg.toString(); } System.out.println("Message Received: "+ msgText ); if (msgText.equalsIgnoreCase("quit")) { synchronized(this) { quit = true; this.notifyAll(); // Notify main thread to quit } } } catch (JMSException jmse) { System.err.println("An exception occurred: "+jmse.getMessage()); } } /** * Creates all the necessary objects for receiving * messages from a JMS queue. * * @param ctx JNDI initial context * @param queueName name of queue * @exception NamingException if operation cannot be performed * @exception JMSException if JMS fails to initialize due to internal error */ public void init(Context ctx, String queueName) throws NamingException, JMSException { qconFactory = (QueueConnectionFactory) ctx.lookup(JMS_FACTORY); qcon = qconFactory.createQueueConnection(); qsession = qcon.createQueueSession(false, Session.AUTO_ACKNOWLEDGE); queue = (Queue) ctx.lookup(queueName); qreceiver = qsession.createReceiver(queue); qreceiver.setMessageListener(this); qcon.start(); } /** * Closes JMS objects. * @exception JMSException if JMS fails to close objects due to internal error */ public void close()throws JMSException { qreceiver.close(); qsession.close(); qcon.close(); } /** * main() method. * * @param args WebLogic Server URL * @exception Exception if execution fails */ public static void main(String[] args) throws Exception { if (args.length != 1) { System.out.println("Usage: java examples.jms.queue.QueueReceive WebLogicURL"); return; } InitialContext ic = getInitialContext(args[0]); QueueReceive qr = new QueueReceive(); qr.init(ic, QUEUE); System.out.println( "JMS Ready To Receive Messages (To quit, send a \"quit\" message)."); // Wait until a "quit" message has been received. synchronized(qr) { while (! qr.quit) { try { qr.wait(); } catch (InterruptedException ie) {} } } qr.close(); } private static InitialContext getInitialContext(String url) throws NamingException { Hashtable env = new Hashtable(); env.put(Context.INITIAL_CONTEXT_FACTORY, JNDI_FACTORY); env.put(Context.PROVIDER_URL, url); return new InitialContext(env); } } 2. How to Use This Class 2.1 From the file system on Linux This section describes how to use the class from the file system of a WebLogic Server installation. Log in to a machine with a WebLogic Server installation and create a directory to contain the source and code matching the package name, e.g. span$HOME/examples/jms/queue. Copy the above QueueReceive.java file to this directory. Set the CLASSPATH and environment to match the WebLogic server environment. Go to $MIDDLEWARE_HOME/user_projects/domains/base_domain/bin  and execute . ./setDomainEnv.sh Collect the following information required to run the script: The JNDI name of the JMS queue to use In the WebLogic server console > Services > Messaging > JMS Modules > Module name, (e.g. TestJMSModule) > JMS queue name, (e.g. TestJMSQueue) select the queue and note its JNDI name, e.g. jms/TestJMSQueue The JNDI name of the connection factory to use to connect to the queue Follow the same path as above to get the connection factory for the above queue, e.g. TestConnectionFactory and its JNDI name e.g. jms/TestConnectionFactory The URL and port of the WebLogic server running the above queue Check the JMS server for the above queue and the managed server it is targeted to, for example soa_server1. Now find the port this managed server is listening on, by looking at its entry under Environment > Servers in the WLS console, e.g. 8001 The URL for the server to be passed to the QueueReceive program will therefore be t3://host.domain:8001 e.g. t3://jbevans-lx.de.oracle.com:8001 Edit Queue Receive .java and enter the above queue name and connection factory respectively under ... public final static String JMS_FACTORY="jms/TestConnectionFactory"; ... public final static String QUEUE="jms/TestJMSQueue"; ... Compile Queue Receive .java using javac Queue Receive .java Go to the source’s top-level directory and execute it using java examples.jms.queue.Queue Receive   t3://jbevans-lx.de.oracle.com:8001 This will print a message that it is ready to receive messages or to send a “quit” message to end. The program will read all messages in the queue and print them to the standard output until it receives a message with the payload “quit”. 2.2 From JDeveloper The steps from JDeveloper are the same as those used for the previous program QueueSend.java, which is used to send a message to the queue. So we won't repeat them here. Please see the previous blog post at JMS Step 2 - Using the QueueSend.java Sample Program to Send a Message to a JMS Queue and apply the same steps in that example to the QueueReceive.java program. This concludes the example. In the following post we will create a BPEL process which writes a message based on an XML schema to the queue.

  Read the article

• How to fix "apt-get upgrade" errors?

  - by mohamad farid bin abdullah

  I get these errors when I try to upgrade the packages installed on my Ubuntu system: m@m-desktop ~ $ sudo apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 2 not fully installed or removed. After this operation, 0B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up drbd8-source (2:8.3.7-1ubuntu2.3) ... Removing old drbd8-8.3.7 DKMS files... ------------------------------ Deleting module version: 8.3.7 completely from the DKMS tree. ------------------------------ Done. Loading new drbd8-8.3.7 DKMS files... First Installation: checking all kernels... Building only for 2.6.35-22-generic Building for architecture i386 Building initial module for 2.6.35-22-generic Error! Bad return status for module build on kernel: 2.6.35-22-generic (i386) Consult the make.log in the build directory /var/lib/dkms/drbd8/8.3.7/build/ for more information. dpkg: error processing drbd8-source (--configure): subprocess installed post-installation script returned error exit status 10 dpkg: dependency problems prevent configuration of drbd8-utils: drbd8-utils depends on drbd8-source; however: Package drbd8-source is not configured yet. dpkg: error processing drbd8-utils (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: drbd8-source drbd8-utils E: Sub-process /usr/bin/dpkg returned an error code (1) m@m-desktop ~ $

  Read the article

• hp pavilion g6 1250 with a BCM 4313 doesn't see any wireless networks

  - by Ahmed Kotb

  i have tried using ubuntu 10.04 and ubuntu 11.10 and both have the same problem the driver is detected by the additional propriety drivers wizard and after installation, ubuntu can't see except on wireless network which is not mine (and i can't connect to it as it is secured) There are plenty of wireless networks around me but ubuntu can't detect them and if i tried to connect to one of them as if it was hidden connection time out. the command lspci -nvn | grep -i net gives 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) iwconfig gives lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off i guess it is something related to Broadcom driver .. but i don't know , any help will be appreciated UPDATE: ok i installed a new copy of 11.10 to remove the effect of any trials i have made i followed the link (http://askubuntu.com/q/67806) as suggested all what i have done now is trying the command lsmod | grep brc and it gave me the following brcmsmac 631693 0 brcmutil 17837 1 brcmsmac mac80211 310872 1 brcmsmac cfg80211 199587 2 brcmsmac,mac80211 crc_ccitt 12667 1 brcmsmac then i blacklisted all the other drivers as mentioned in the link the wireless is still disabled.. in the last installation installing the Brodcom STA driver form the additional drivers enabled the menu but as i have said before it wasn't able to connect or even get a list of available networks so what should i do now ? the output of command rfkill list all rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• unable to install anything that depends upon spamassassin. Cant even install spamassasin

  - by Harbhag

  I am trying to install mailscanner using apt-get install mailscanner and I got the following error Setting up spamassassin (3.3.1-1) ... Starting SpamAssassin Mail Filter Daemon: child process [21344] exited or timed out without signaling production of a PID file: exit 255 at /usr/sbin/spamd line 2588. invoke-rc.d: initscript spamassassin, action "start" failed. dpkg: error processing spamassassin (--configure): subprocess installed post-installation script returned error exit status 255 dpkg: dependency problems prevent configuration of mailscanner: mailscanner depends on spamassassin (>= 3.1); however: Package spamassassin is not configured yet. dpkg: error processing mailscanner (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: spamassassin mailscanner E: Sub-process /usr/bin/dpkg returned an error code (1) and when I tried to install spamassassin I got the following error : Setting up spamassassin (3.3.1-1) ... Starting SpamAssassin Mail Filter Daemon: child process [21389] exited or timed out without signaling production of a PID file: exit 255 at /usr/sbin/spamd line 2588. invoke-rc.d: initscript spamassassin, action "start" failed. dpkg: error processing spamassassin (--configure): subprocess installed post-installation script returned error exit status 255 dpkg: dependency problems prevent configuration of mailscanner: mailscanner depends on spamassassin (>= 3.1); however: Package spamassassin is not configured yet. dpkg: error processing mailscanner (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: spamassassin mailscanner E: Sub-process /usr/bin/dpkg returned an error code (1) I am using Ubuntu Server 10.04

  Read the article

• SQL SERVER – Installing Data Quality Services (DQS) on SQL Server 2012

  - by pinaldave

  Data Quality Services is very interesting enhancements in SQL Server 2012. My friend and SQL Server Expert Govind Kanshi have written an excellent article on this subject earlier on his blog. Yesterday I stumbled upon his blog one more time and decided to experiment myself with DQS. I have basic understanding of DQS and MDS so I knew I need to start with DQS Client. However, when I tried to find DQS Client I was not able to find it under SQL Server 2012 installation. I quickly realized that I needed to separately install the DQS client. You will find the DQS installer under SQL Server 2012 >> Data Quality Services directory. The pre-requisite of DQS is Master Data Services (MDS) and IIS. If you have not installed IIS, you can follow the simple steps and install IIS in your machine. Once the pre-requisites are installed, click on MDS installer once again and it will install DQS just fine. Be patient with the installer as it can take a bit longer time if your machine is low on configurations. Once the installation is over you will be able to expand SQL Server 2012 >> Data Quality Services directory and you will notice that it will have a new item called Data Quality Client.  Click on it and it will open the client. Well, in future blog post we will go over more details about DQS and detailed practical examples. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQL Utility, T SQL, Technology Tagged: Data Quality Services

  Read the article

• Read only file system

  - by Jack Moon

  I'm running Ubuntu 12.10, Upon opening any shell I get the following error: /home/jack/.rbenv/libexec/rbenv-init: line 87: cannot create temp file for here-document: Read-only file system I realised this wasn't simply a rbenv issue, as any file I try to write to returns an error saying the system is Read-only. I don't know how else to describe my problem, each time I boot up the system goes through a disk check, where it supposedly fixes several errors in my disk. Here is my /etc/fstab # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda1 during installation UUID=1cc4b2ab-a984-4516-ac25-6d64f5050244 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=4e0dfeae-701a-43ce-b5c6-65f15ab3d8e3 none swap sw 0 0 The entire file system is read-only. I've tried the following sudo fsck.ext4 -f /dev/sda1 which gave the following (shortened) output /dev/sda1: ***** FILE SYSTEM WAS MODIFIED ***** /dev/sda1: ***** REBOOT LINUX ***** /dev/sda1: 1257080/45268992 files (1.0% non-contiguous), 50696803/181051904 blocks

  Read the article

• SQL SERVER – FIX: ERROR Msg 5169, Level 16: FILEGROWTH cannot be greater than MAXSIZE for file

  - by pinaldave

  I am writing this blog post right after I resolve this error for one of the system. Recently one of the my friend who is expert in infrastructure as well private cloud was working on SQL Server installation. Please note he is seriously expert in what he does but he has never worked SQL Server before and have absolutely no experience with its installation. He was modifying database file and keep on getting following error. As soon as he saw me he asked me where is the maxfile size setting so he can change. Let us quickly re-create the scenario he was facing. Error Message: Msg 5169, Level 16, State 1, Line 1 FILEGROWTH cannot be greater than MAXSIZE for file ‘NewDB’. Creating Scenario: CREATE DATABASE [NewDB] ON PRIMARY (NAME = N'NewDB', FILENAME = N'D:\NewDB.mdf' , SIZE = 4096KB, FILEGROWTH = 1024KB, MAXSIZE = 4096KB) LOG ON (NAME = N'NewDB_log', FILENAME = N'D:\NewDB_log.ldf', SIZE = 1024KB, FILEGROWTH = 10%) GO Now let us see what exact command was creating error for him. USE [master] GO ALTER DATABASE [NewDB] MODIFY FILE ( NAME = N'NewDB', FILEGROWTH = 1024MB ) GO Workaround / Fix / Solution: The reason for the error is very simple. He was trying to modify the filegrowth to much higher value than the maximum file size specified for the database. There are two way we can fix it. Method 1: Reduces the filegrowth to lower value than maxsize of file USE [master] GO ALTER DATABASE [NewDB] MODIFY FILE ( NAME = N'NewDB', FILEGROWTH = 1024KB ) GO Method 2: Increase maxsize of file so it is greater than new filegrowth USE [master] GO ALTER DATABASE [NewDB] MODIFY FILE ( NAME = N'NewDB', FILEGROWTH = 1024MB, MAXSIZE = 4096MB) GO I think this blog post will help everybody who is facing similar issues. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Error Messages, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• Cannot get webapps to work after upgrade from 12.04 to 12.10

  - by kashan

  I just upgraded to Ubuntu 12.10 from 12.04. But I cannot use WebApps. In fact there is no sign of them anywhere. Firefox and Chromium are not prompting for integration. I tried re-installing both browsers/webapps plugin of each, but no luck. Out of curiousity, I tried to install unity-webapps-preview through terminal, apt-get reported that this operation is going to need 127mb. After installation, restarting session, nothing. I re-ran the unity-webapp-preview in terminal and SURPRISINGLY it again asked me that this operation is going to need 58mb. After Installation, nothing. Firefox is showing the unity-webapp plugin in Extensions but in Preferences there is noting like Unity settings or options for exceptions in General tab (as I seen in some threads). Chromium is not even showing the plugin in Extensions nor in the settings. Really need help. I know there is a reported bug but it is mostly about the complains that the webapps are not working as they should but in my case they don't seem to exist. EDIT: The out put of gsettings list-recursively | grep webapp is: com.canonical.unity.webapps allowed-domains @as [] com.canonical.unity.webapps dontask-domains @as [] com.canonical.unity.webapps index-update-time 43200 com.canonical.unity.webapps integration-allowed true com.canonical.unity.webapps preauthorized-domains ['amazon.ca', 'amazon.cn', 'amazon.com', 'amazon.co.uk', 'amazon.de', 'amazon.es', 'amazon.fr', 'amazon.it', 'www.amazon.ca', 'www.amazon.cn', 'www.amazon.com', 'www.amazon.co.uk', 'www.amazon.de', 'www.amazon.es', 'www.amazon.fr', 'www.amazon.it', 'one.ubuntu.com']

  Read the article

• How do I resolve a plugin conflict in Eclipse?

  - by Jason Thompson

  I'd like to upgrade my Helios installation of Eclipse to Indigo. When I do, I get the following message: Cannot complete the install because of a conflicting dependency. Software being installed: Eclipse IDE for Java EE Developers 1.4.2.20120213-0813 (epp.package.jee 1.4.2.20120213-0813) Software currently installed: Oracle GlassFish Server Tools 1.6.1.201009290929 (oracle.eclipse.tools.helios.glassfish.feature.group 1.6.1.201009290929) So my first thought was to simply uninstall GlassFish. For the life of me, I can't figure out how and where to go to do this. I went to Help-About Eclipse...-Installation Details. The only place that it looks like I can uninstall stuff is in the "Installed Software" tab. I do not see the Oracle Glassfish package anywhere. If I go to "Feature" or "Plug-ins", I can find it just fine, but there is no option to uninstall. So my next thought was to upgrade Glassfish. So I put the indigo repo in there, but I still get the same message when trying to update. Any ideas?

  Read the article

• View Word Definitions in IE 8 with the Define with Bing Accelerator

  - by Asian Angel

  Do you need an easy way to view word definitions while browsing with Internet Explorer? The Define with Bing Accelerator will display definitions in the same (or a new) tab and save you time while browsing. Using Define with Bing The installation consists of two steps. First, click on Add to Internet Explorer to start the process. Next you will be asked to confirm the installation. Once you have clicked Add your new accelerator is ready to use (no browser restart required). Whenever you encounter a word that needs defining highlight it, click on the small blue square, go to All Accelerators, and then Define with Bing. There are two ways to access the definition: Hover your mouse over the Define with Bing text to open a small popup window Click on Define with Bing to open a definition search in a new tab Being able to access a definition or explanation in the same tab will definitely save you time while browsing. In the example shown here you can get an idea of what SCORM means but clicking on the links inside the popup window is not recommended (webpage opens in popup and is not resizable). In the situation shown above it is better to click on Define with Bing and see more information in a new tab. Conclusion The Define with Bing Accelerator can be a very useful time saver while browsing with Internet Explorer. Finding those word definitions will be a much more pleasant experience now. Add the Define with Bing Accelerator to Internet Explorer Similar Articles Productive Geek Tips Add Google Dictionary Power to ChromeChoose Custom New Tab Pages in ChromeSearch Alternative Search Engines from within Bing’s Search PageView Word Definitions in Google Chrome with DictionaryTipThe New Bing Bar Provides Easy Access to Searches and Microsoft Live Services TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 VMware Workstation 7 Acronis Online Backup Sculptris 1.0, 3D Drawing app AceStock, a Tiny Desktop Quote Monitor Gmail Button Addon (Firefox) Hyperwords addon (Firefox) Backup Outlook 2010 Daily Motivator (Firefox)

  Read the article

• Ubuntu eats itself after I followed updater instruction

  - by Tony Martin

  Updater (I assume) put a no entry style alert icon on the panel which informed me that certain package dependencies were not up to snuff. Upgrades were thereafter only partial. The dialogue advised that I (and this is from noob memory) sudo apt-get install -f. I did this and typed in the confirmation phrase and watched apt-get systematically remove every component of linux, both the stuff I installed and the core ubuntu packages. I could only assume at this stage that this was for a fresh install but of course, I know better now. There's much complaint about Windows, but I've never met with advice from Microsoft tools to wipe out the operating system because of a couple of missing .dlls. So what gives? This was a 64 bit install of 12.04. All that is left is grub pointing to a couple of windows recovery partitions on the hard drive. I'm tempted, but I have hopes of recovering the data that I had enough misguided faith to trust to the linux ext4 partition. I've tried pen driving back into it with a 32 bit iso but I'm simply informed that ubuntu is running in low graphics mode and get to watch the dots cycle indefinitely. EDIT: Thanks for the advice vis positive request. I've got onto the machine with a 64 bit stick and can see the file structure left behind by the installation. My first instinct was to run install from the stick but it did not seem to offer a recovery option. My question then: is there a way to recover the current installation so that if I reinstall the packages I had they will pick up the original settings. I'm particularly worried about losing email from evolution - the rest I could probably lash back together. I would also be interested how this disaster came about. I see people in the know recommending this same procedure in similar circumstances. Thanks for your attention, Tony Martin

  Read the article

• 12.04: Persistent Gimp 2.2 from Gimphoto or Gimpshop. Cannot install 2.8

  - by Jorge M. Treviño

  I have a very messed up installation of Gimp. Some time ago I installed Gimpshop or Gimphoto (can't really remember which) and it installed Gimp 2.2. Didn't work for me and tried to remove it. I've followed all Gimp remove, autoremove, clean, update and upgrade instructions I've found here to no avail. Now Software Center doesn't even show 2.8 but instead it does 2.6. I've installed and removed Gimp from terminal nth times. Running Gimp from the dash doesn't do anything but entering "Gimp" in the terminal prompt gives me a 2.2 installation screen. Cannot for the life of me find and remove the darn leftover garbage. How can I completely clean my system (12.04, fully updated today) from everything Gimp so I can give 2.8 a try? Anticipated apologies if this is a dupe but I've run through all messages with a Gimp tag and none has helped me. sudo apt-get install -f gives me 0,0,0,0. Thanks in advance.

  Read the article

• How to solve package issues/dependencies

  - by Wolfgang Kuehne

  Background info I am trying to install Veins simulation environment by following the tutorial provided by the author. In step 1 it is required to install some packages in Linux, the tutorial suggest this commands to be executed on Terminal: sudo apt-get install build-essential gcc g++ bison flex perl tcl-dev tk-dev blt libxml2-dev zlib1g-dev default-jre doxygen graphviz libwebkitgtk-1.0-0 openmpi-bin libopenmpi-dev libpcap-dev autoconf automake libtool libxerces-c2-dev proj libgdal1-dev libfox-1.6-dev When I execute this command, I immediately get: E: Package 'proj' has no installation candidate Then I remove the proj from the command and execute it again without proj in it, next I get: The following packages have unmet dependencies: libgdal1-dev : Depends: libgdal-dev but it is not going to be installed E: Unable to correct problems, you have held broken packages. So, I remove libgdal1-dev from the command as well. And it executes file, by downloading the remaining packages. To troubleshoot the problem with proj and libdgal1-dev I go to the Synaptic Package Manager. libgdal1-dev I search for libgdal1-dev in Synaptic Package Manager and I get an entry. I Mark for Installation and then Synaptic Package Manager suggests removing libxerces-c2-dev which is actually added via the initial command. Should I trust Synaptic Package Manager with this suggestion, and proceed further? proj What should I do about proj. There are some packages in Synaptic Package Manager such as proj-bin or libproj-dev. Should I install them? I think proj has to do with this and this What should I do to make sure that this simulation tool works fine?

  Read the article

• SQL SERVER – How to Install SQL Server 2014 – A 99 Seconds Video

  - by Pinal Dave

  Last month I presented at 3 community and 5 corporate events. Every single time I have been asked by others what is my experience with SQL Server 2014. Every single time I have told the audience that they should try this out themselves, however, the response has been very lukewarm. Everybody wants to know how SQL Server 2014 works, but no one wants to try out themselves. Upon asking why users are not installing SQL Server 2014, pretty much the same answer I received from everyone – “The Fear of Uknown”. Everybody who have not installed SQL Server 2014 are not sure how the installation process works and what if they face any issue while installing SQL Server 2014. If you have installed an earlier version of SQL Server, installing SQL Server 2014 is very easy process. I have created a quick video of 99 seconds where I explain how we can easily install SQL Server 2014. This is a straight forward default installation of SQL Server. Reference: Pinal Dave (http://blog.sqlauthority.com)Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Video

  Read the article

• hp pavilion g6 1250 wireless problems

  - by Ahmed Kotb

  i have tried using ubuntu 10.04 and ubuntu 11.10 and both have the same problem the driver is detected by the additional propriety drivers wizard and after installation , ubuntu can't see except on wireless network which is not mine (and i can't connect to it as it is secured) there are plenty of wireless networks around me but ubuntu can't detect them and if i tried to connect to one of them as if it was hidden connection time out. the command lspci -nvn | grep -i net gives 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) iwconfig gives lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off i guess it is something related to Broadcom driver .. but i don't know , any help will be appreciated UPDATE: ok i installed a new copy of 11.10 to remove the effect of any trials i have made i followed the link (http://askubuntu.com/q/67806) as suggested all what i have done now is trying the command lsmod | grep brc and it gave me the following brcmsmac 631693 0 brcmutil 17837 1 brcmsmac mac80211 310872 1 brcmsmac cfg80211 199587 2 brcmsmac,mac80211 crc_ccitt 12667 1 brcmsmac then i blacklisted all the other drivers as mentioned in the link the wireless is still disabled.. in the last installation installing the Brodcom STA driver form the additional drivers enabled the menu but as i have said before it wasn't able to connect or even get a list of available networks so what should i do now ? the output of command rfkill list all rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

< Previous Page | 248 249 250 251 252 253 254 255 256 257 258 259  | Next Page >