Search Results

Search found 18364 results on 735 pages for 'nova network'.

Page 254/735 | < Previous Page | 250 251 252 253 254 255 256 257 258 259 260 261  | Next Page >

• Troubles uploading big pics to Picassa when pics are on NAS

  - by Bascy

  Hi all, I'm working from Vista a laptop on a WLAN, my pictures are all on a shared (samba) network drive on a FreeNAS system, which has a wired network connection to the WLAN router (DLink 655). I'v noticed that when i try to upload pics to picassa, and select files from the network share the pics won't upload successfully. If i first copy them locally (on the laptop) and then upload them to picassa, everything works fine. If i try to copy smaller pics (<500kB) it doesnt go wrong Anybody know what is going wrong here?

  Read the article

• auto-summarization: classful vs classless routing protocols

  - by yorble

  Suppose a router R1 is directly connected to the following subnets: 10.1.0.0/24 10.1.1.0/24 10.1.2.0/24 10.1.3.0/24 If it is running RIPv1, it will advertise: "i have the network 10.0.0.0" (implicitly understood by receiving RIPv1 routers as 10.0.0.0/8 because the protocol is classful) but suppose we changed the routing protocol to RIPv2 and turned ON auto-summarization. Would it behave in the same way? Would it advertise: "i have the network 10.0.0.0" (advertised WITHOUT subnet mask, and implicitly understood by other routers as 10.0.0.0/8) OR would it auto-summarize in a non classful way like: "i have 10.1.0.0/22" (advertised as network id and subnet mask pair) In other words, does turning on auto-summarization in RIPv2 (or other classless routing protocols) cause it to auto-summarize in a classful manner or simply auto-summarize classlessly to the best of its ability?

  Read the article

• Juju didn't configure rabbitmq for openstack?

  - by SaM

  I have installed ubuntu Openstack HA with juju with all 24 servers. But my openstack is not working at all. On dashboard on every page I get errors saying "could not retrieve usage information", "could not retrieve volume information, "could not retrieve .....etc I spent hours and have discovered that juju has not done configuration correctly. I found that on cloud controller in nova.conf juju has added rabitmq vhost enrty, but that virtual host is not added in rabbitmq. Then how is its suppose to work? And on juju-gui canvas rabbimq is all green and is working fine, which in reality its not. I am really wondering if juju has really done correct configuration in all 24 servers now, I am getting the feeling that it would have been faster if I would have done openstack deployment manually instead of using juju. Why was the virtual host entry not added in rabbitmq? How should I solve this?

  Read the article

• South Florida Code Camp 2011 - 02/12/2011 - Final Days to register

  - by Nikita Polyakov

  South Florida Code Camp - 02/12/2011 - Final Days to register 13 tracks, 78 sessions, 65 speakers Topics include: Windows Phone 7, Silverlight, Web dev, Architecture/Agile, Sharepoint and SQL Networking with 700 other software developers, over 800 already registered! Free breakfast and lunch Hobnob with speakers, MVP's and authors Party afterwards with attendees and speakers Convenient location at Nova University in Davie Free XBOX 360 Kinect 250 GB raffle (must be present) Free raffle of valuable software, books and swag Free Code Camp T-shirt Book swap - see site for details You get to say "I was there!" More information: http://www.fladotnet.com/codecamp   Register now at: https://www.clicktoattend.com/invitation.aspx?code=150628 (some people have had a problem with this link but click again and it should work). I am presenting Windows Phone Marketplace session. Marketplace and Monetization Details of Windows Phone Marketplace and using Microsoft Advertising SDK control. Monetization strategies, rules and tips for making the best out of your post writing the Windows Phone app experience. Many speakers end up hanging out in the back and this session turns into a open discussion panel.

  Read the article

• Need assistance setting up Linux Router with 2 public lans

  - by user195407

  I was assigned a.b.c.10/30 (Public IP) for my router and given a.b.c.9 as the gateway. I was also assigned x.y.z.128/25 (Public IP block) for my use. I want to setup a Linux router to handle this situation. My Linux box has 3 NICs, eth0 is a.b.c.10, eth1 I have assigned x.y.z.254, eth2 is unused at present. I have eth1 connected to a network switch, and several devices connected. Let's say box A is x.y.z.129 with a gateway of x.y.z.254. I have not connected to the network yet, as it is not live. What settings do I need to make, beyond adding the 2 network definitions to the cards and having "route add default gw a.b.c.9 eth0"? I may add a private 192.168.100.0/24 lan to eth2 later.

  Read the article

• 2 routers, both DHCP, no IP assigned

  - by piobyz

  I can't get DHCP to assign IP to my wireless devices. My network config is as follows: Nanostation5 Linksys WRT350N, which is connected with Nanostation via its INTERNET port. Nanostation: LAN IP Address: 192.168.1.20 WLAN IP Address: 192.168.0.79 Network Mode: Router and is getting its IP via DHCP from my ISP Netmask: 255.255.255.0 Gateway IP: 192.168.1.1 LAN Network settings: IP Address: 192.168.1.20 Netmask: 255.255.255.0 Enable NAT: YES ENABLE DHCP Server: YES Range 192.168.1.100 ~ 250 Netmask: 255.255.255.0 Enable DNS Proxy: YES Linksys: Internet Connection Type: DHCP Router IP: 192.168.2.1 Subnet Mask: 255.255.255.0 DHCP: Enabled Start IP: 192.168.2.100 ~ 120 Advanced Routing: NAT: Enabled What I can do is connecting manually with this config: IP: 192.168.2.101 Subnet Mask: 255.255.255.0 Router: 192.168.2.1 DNS: 192.168.1.20 Search domains: WRT350N I want to be able to connect to both routers independently(now its 192.168.1.20 for Nanostation, and 192.168.2.1 for Linksys) and connect any wireless device using DHCP. What should be IP ranges, masks, etc. on both devices?

  Read the article

• acessing a subnetwork from within a vm

  - by yan bellavance

  I have a pc running windows 7. I have vmwareplayer running RHEL5 I have 1 physical ethernet connection. this ethernet connection is wired to a hub. there is another device on that hub that needs to be in a certain subnetwork (192.168.0.xxx)(lets call him device X) but the general network is 192.168.1.xxx How can I configure the network adapters so that I can ping device X from RHEL5 in the vm. Originally I could ping google from both windows and rhel (I was in the .1 network) but not device X since he is on a different subnetwork address. Now that I have put it on the .0 I can ping device X from windows but not from rhel5 and cannot access the web. I did this by manually setting the IP address.

  Read the article

• Can't the NetworkManager applet to appear in the Gnome panel in Ubuntu

  - by Nate

  I have researched this problem extensively and I can't seem to find an answer. In Ubuntu 10.04 LTS, I want to connect to my VPN through the NetworkManager applet. I installed all the network manager packages, including the gnome client. I understand I need to add the "Notification Area" to the panel, which I have done. I checked that the NetworkManager is running: nate@nate-desktop:~$ service network-manager status network-manager start/running, process 763 In /etc/NetworkManager/nm-system-settings.conf, I have added managed=true (don't know if this matters, but I saw it suggested on one forum): nate@nate-desktop:~$ more /etc/NetworkManager/nm-system-settings.conf # This file is installed into /etc/NetworkManager, and is loaded by # NetworkManager by default. To override, specify: '--config file' # during NM startup. This can be done by appending to DAEMON_OPTS in # the file: # # /etc/default/NetworkManager # [main] plugins=ifupdown,keyfile [ifupdown] #managed=false managed=true At this point, it looks like NetworkManager is running but it's not appearing in the NotificationArea of the panel. I don't know what else to try. Any ideas?

  Read the article

• Cannot Access a Shared Folder Using Windows 2008

  - by peter

  Hi All, I have a NAS drive, and this is sharing some folders. I cannot access those folders from a windows 2008 machine which is on the network. The are both connected to the same network switch. e.g. if I go like this, \\server\ or \\server\folder I get the message 'windows cannot access \\server check the spelling, click diagnose' etc. Error code: 0x80004005 The thing is that I can connect to this shared drive from a windows 7 laptop connected wirelessly to the same network. I can ping the server from windows 2008, but only if I use the IP address, not the server name.

  Read the article

• Can't the NetworkManager applet to appear in the Gnome panel in Ubuntu

  - by Nate

  I have researched this problem extensively and I can't seem to find an answer. In Ubuntu 10.04 LTS, I want to connect to my VPN through the NetworkManager applet. I installed all the network manager packages, including the gnome client. I understand I need to add the "Notification Area" to the panel, which I have done. I checked that the NetworkManager is running: nate@nate-desktop:~$ service network-manager status network-manager start/running, process 763 In /etc/NetworkManager/nm-system-settings.conf, I have added managed=true (don't know if this matters, but I saw it suggested on one forum): nate@nate-desktop:~$ more /etc/NetworkManager/nm-system-settings.conf # This file is installed into /etc/NetworkManager, and is loaded by # NetworkManager by default. To override, specify: '--config file' # during NM startup. This can be done by appending to DAEMON_OPTS in # the file: # # /etc/default/NetworkManager # [main] plugins=ifupdown,keyfile [ifupdown] #managed=false managed=true At this point, it looks like NetworkManager is running but it's not appearing in the NotificationArea of the panel. I don't know what else to try. Any ideas?

  Read the article

• Rip authedicatation from LDAP to Local

  - by oxinabox

  We are taking a small portion of out network offline, and running a separate network using that portion. (By small portion I mean 2 servers, that will be connected to 30 odd boxs that aren't usually part of our network, and don't need to authenicate) I intend to create a VM on one of the servers to provide general user services, and IRC server, remote shell etc. And I would like the users to be able to use there usual server log in details. Problem is the LDAP server that normally checks those details is not one of the severs. So I need to be able to some how take their details off LDAP and put them on the the server that is coming. One suggestion I had was to set a LDAP server on the VM locally, and clone the LDAP database onto it (using something called slapcat) is this the best way? Or can I I change the LDAP data into local authentication data?

  Read the article

• Apache server in raspberry PI not visible from outside( public IP)

  - by Kronos

  I have made a fresh install of Arch Linux ARM into a Raspberry PI and I mounted there a LAMP, all fresh. I have another Arch(x86) in my laptop with Apache also there, and as far as I know, two web servers cannot run in the same network segment so, the problem is as follows. I my laptop, having Apache running, if I enter via the public ip of my network everything turns ok and I can see my website but, (obviously turning this server down) if I enter from the public IP with the Apache running in the raspberry pi( yes, only that Apache running) i cannot see my website in there. Also, if I access via local network it is a normal success, I can see my website. So, I can enter my raspberry website only via local but in my other web server i can enter it via local and public. I have the same conf files in both of them so what is the difference? I was planning in making the rpi as a development server. Thanks in advance

  Read the article

• Shared Folders in VirtualBox on Windows 7

  In my adventures with VirtualBox, my latest victory was in figuring out how to share folders between my host OS (Windows 7) and my virtual OS (Windows Server 2008).  Im familiar with VirtualPC and other such products, which allow you to share local folders with the VM.  When you do, they just show up in Windows Explorer and all is good.  However, after configuring shared folders in VirtualBox like so:   I couldnt see them anywhere within the machine. Where are Shared Folders in a VirtualBox VM? Fortunately a bit of searching yielded this article, which describes the problem nicely.  It turns out that there is a magic word you have to know, and that is the share name for the host OS: \\vboxsrv Once you know this, mapping shared folders is straightforward.  From Windows Explorer, click on the Map network drive option, and then map a drive to \\vboxsrv\YOURSHAREDFOLDER Like so: With that, its easy to share folders between the client and host OS using VirtualBox.  The reason I didnt simply use a standard network share to my host OS machine name is that both guest and host are in a VPN, and the VPN is over the Internet and in a different country, so when I went that route my files were (apparently) traveling from host to guest by way of the remote VPN network, rather than locally.  Using the Shared Folders feature dramatically sped up my ability to transfer files between Host and Guest machines. Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• iptables forward rule not working in openwrt

  - by Udit Gupta

  I am trying to apply some iptables forwarding rules in openwrt. Here is my scenario - My server has two cards ath0 and br-lan. br-lan is connected to internet and ath0 to private network. The other m/c in n/w also has ath0 that connects with this server's ath0 and they are able to ping each other. Now, I want other m/c in network to use internet using br-lan of server so I thought of using iptables forwarding rule- Here is what I tried - Server : $ ping 1.1.1.6 // <ath0-ip of client> works fine $ iptables -A FORWARD -i ath0 -o br-lan -j ACCEPT $ /etc/init.d/firewall restart Client : $ ping 1.1.1.5 // <ath0-ip of server> works fine $ ping 132.245.244.60 // <br-lan ip of server> (not working) I am new to iptables stuff and openwrt. What I am doing wrong here ?? Any other help if anyone could suggest for my scenario Edit- m/c - machine n/w - network

  Read the article

• Homework with allocate subnet IP address

  - by Don Lun

  I'm having difficulty solving a subnet allocation homework problem. Assume that a university has an address block 128.205.224.0/19. It has to allocate addresses for 2 departments' networks, each of size 1800, and for 4 offices, of sizes 550, 600, 650, and 750 nodes respectively. Assuming that the university network allocates addresses sequentially from the beginning of the allocated allocated address space, what are the prefix allocations for these subnetworks? I first thought in this way: There should be 6 subnets in the network. So I need 3 bits for the subnets. So 3 + 19 = 22 bits should be the network bits. Then there are only 10 bits left. 2^10 = 1024 < 1800, so this cannot work. Could you guys give me a hint or some thoughts for solving this problem?

  Read the article

• vSphere ESX 5.5 hosts cannot connect to NFS Server

  - by Gerald

  Summary: My problem is I cannot use the QNAP NFS Server as an NFS datastore from my ESX hosts despite the hosts being able to ping it. I'm utilising a vDS with LACP uplinks for all my network traffic (including NFS) and a subnet for each vmkernel adapter. Setup: I'm evaluating vSphere and I've got two vSphere ESX 5.5 hosts (node1 and node2) and each one has 4x NICs. I've teamed them all up using LACP/802.3ad with my switch and then created a distributed switch between the two hosts with each host's LAG as the uplink. All my networking is going through the distributed switch, ideally, I want to take advantage of DRS and the redundancy. I have a domain controller VM ("Central") and vCenter VM ("vCenter") running on node1 (using node1's local datastore) with both hosts attached to the vCenter instance. Both hosts are in a vCenter datacenter and a cluster with HA and DRS currently disabled. I have a QNAP TS-669 Pro (Version 4.0.3) (TS-x69 series is on VMware Storage HCL) which I want to use as the NFS server for my NFS datastore, it has 2x NICs teamed together using 802.3ad with my switch. vmkernel.log: The error from the host's vmkernel.log is not very useful: NFS: 157: Command: (mount) Server: (10.1.2.100) IP: (10.1.2.100) Path: (/VM) Label (datastoreNAS) Options: (None) cpu9:67402)StorageApdHandler: 698: APD Handle 509bc29f-13556457 Created with lock[StorageApd0x411121] cpu10:67402)StorageApdHandler: 745: Freeing APD Handle [509bc29f-13556457] cpu10:67402)StorageApdHandler: 808: APD Handle freed! cpu10:67402)NFS: 168: NFS mount 10.1.2.100:/VM failed: Unable to connect to NFS server. Network Setup: Here is my distributed switch setup (JPG). Here are my networks. 10.1.1.0/24 VM Management (VLAN 11) 10.1.2.0/24 Storage Network (NFS, VLAN 12) 10.1.3.0/24 VM vMotion (VLAN 13) 10.1.4.0/24 VM Fault Tolerance (VLAN 14) 10.2.0.0/24 VM's Network (VLAN 20) vSphere addresses 10.1.1.1 node1 Management 10.1.1.2 node2 Management 10.1.2.1 node1 vmkernel (For NFS) 10.1.2.2 node2 vmkernel (For NFS) etc. Other addresses 10.1.2.100 QNAP TS-669 (NFS Server) 10.2.0.1 Domain Controller (VM on node1) 10.2.0.2 vCenter (VM on node1) I'm using a Cisco SRW2024P Layer-2 switch (Jumboframes enabled) with the following setup: LACP LAG1 for node1 (Ports 1 through 4) setup as VLAN trunk for VLANs 11-14,20 LACP LAG2 for my router (Ports 5 through 8) setup as VLAN trunk for VLANs 11-14,20 LACP LAG3 for node2 (Ports 9 through 12) setup as VLAN trunk for VLANs 11-14,20 LACP LAG4 for the QNAP (Ports 23 and 24) setup to accept untagged traffic into VLAN 12 Each subnet is routable to another, although, connections to the NFS server from vmk1 shouldn't need it. All other traffic (vSphere Web Client, RDP etc.) goes through this setup fine. I tested the QNAP NFS server beforehand using ESX host VMs atop of a VMware Workstation setup with a dedicated physical NIC and it had no problems. The ACL on the NFS Server share is permissive and allows all subnet ranges full access to the share. I can ping the QNAP from node1 vmk1, the adapter that should be used to NFS: ~ # vmkping -I vmk1 10.1.2.100 PING 10.1.2.100 (10.1.2.100): 56 data bytes 64 bytes from 10.1.2.100: icmp_seq=0 ttl=64 time=0.371 ms 64 bytes from 10.1.2.100: icmp_seq=1 ttl=64 time=0.161 ms 64 bytes from 10.1.2.100: icmp_seq=2 ttl=64 time=0.241 ms Netcat does not throw an error: ~ # nc -z 10.1.2.100 2049 Connection to 10.1.2.100 2049 port [tcp/nfs] succeeded! The routing table of node1: ~ # esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface 10.1.1.0 255.255.255.0 Local Subnet vmk0 10.1.2.0 255.255.255.0 Local Subnet vmk1 10.1.3.0 255.255.255.0 Local Subnet vmk2 10.1.4.0 255.255.255.0 Local Subnet vmk3 default 0.0.0.0 10.1.1.254 vmk0 VM Kernel NIC info ~ # esxcfg-vmknic -l Interface Port Group/DVPort IP Family IP Address Netmask Broadcast MAC Address MTU TSO MSS Enabled Type vmk0 133 IPv4 10.1.1.1 255.255.255.0 10.1.1.255 00:50:56:66:8e:5f 1500 65535 true STATIC vmk0 133 IPv6 fe80::250:56ff:fe66:8e5f 64 00:50:56:66:8e:5f 1500 65535 true STATIC, PREFERRED vmk1 164 IPv4 10.1.2.1 255.255.255.0 10.1.2.255 00:50:56:68:f5:1f 1500 65535 true STATIC vmk1 164 IPv6 fe80::250:56ff:fe68:f51f 64 00:50:56:68:f5:1f 1500 65535 true STATIC, PREFERRED vmk2 196 IPv4 10.1.3.1 255.255.255.0 10.1.3.255 00:50:56:66:18:95 1500 65535 true STATIC vmk2 196 IPv6 fe80::250:56ff:fe66:1895 64 00:50:56:66:18:95 1500 65535 true STATIC, PREFERRED vmk3 228 IPv4 10.1.4.1 255.255.255.0 10.1.4.255 00:50:56:72:e6:ca 1500 65535 true STATIC vmk3 228 IPv6 fe80::250:56ff:fe72:e6ca 64 00:50:56:72:e6:ca 1500 65535 true STATIC, PREFERRED Things I've tried/checked: I'm not using DNS names to connect to the NFS server. Checked MTU. Set to 9000 for vmk1, dvSwitch and Cisco switch and QNAP. Moved QNAP onto VLAN 11 (VM Management, vmk0) and gave it an appropriate address, still had same issue. Changed back afterwards of course. Tried initiating the connection of NAS datastore from vSphere Client (Connected to vCenter or directly to host), vSphere Web Client and the host's ESX Shell. All resulted in the same problem. Tried a path name of "VM", "/VM" and "/share/VM" despite not even having a connection to server. I plugged in a linux system (10.1.2.123) into a switch port configured for VLAN 12 and tried mounting the NFS share 10.1.2.100:/VM, it worked successfully and I had read-write access to it I tried disabling the firewall on the ESX host esxcli network firewall set --enabled false I'm out of ideas on what to try next. The things I'm doing differently from my VMware Workstation setup is the use of LACP with a physical switch and a virtual distributed switch between the two hosts. I'm guessing the vDS is probably the source of my troubles but I don't know how to fix this problem without eliminating it.

  Read the article

• Separating two networks

  - by Farhan Ali

  I have two routers, R1 and R2. R1 (a stock linksys router running dd-wrt) is connected to internet and is serving internet to a network of 5 devices/PCs running a DHCP server, with a network of 192.168.1.0/24. R1 also serves internet services to R2. R2 (a ubuntu server 12.04) gets internet from R1. R2 has 3 PCs attached to it, runs a DHCP server with a network of 172.22.22.0/24. My requirement is that the clients on both sides should not talk to each other at all – with the exception that R1 clients may access the R2 router through its IP of 192.168.1.x. At the moment, R2 clients are able to ping R1 clients, which is unacceptable, whereas R1 clients cannot ping R2 clients, which is OK. I believe iptables could be set up but I don't know how.

  Read the article

• Implement 2x speed in tower of defense type game

  - by Siddharth

  I was currently developing tower of defense game and I want to implement 2x feature for my game. Game usually run with 1x speed that was normal speed of the game. Here what 1x and 2x mean : 1x - mention normal speed of the game, 2x - mention the game object moves with double speed means user experience the fast game play. I want to implement such functionality for my game. The functionality that I want contains in the game Medieval Castle game that was available in the market. https://play.google.com/store/apps/details?id=com.nova.root&feature=search_result#?t=W251bGwsMSwxLDEsImNvbS5ub3ZhLnJvb3QiXQ.. The screen shot also shows the 1x and 2x button in that game. I think for 2x speed of the game I have to increase the speed of each object that were in the game. So any member please help what to do for that implementation. Only idea become enough for me.

  Read the article

• Hyper-V virtual machine unable to get IP address from DHCP server running on same physical box

  - by Bronumski

  We have a Windows server 2008 R2 with two network cards running AD, DHCP, DNS and Hyper-V The first nic is setup with a static IP address and DHCP, WDS, and DNS are bound to it. The second nic is configured in Hyper-V to be only used by Hyper-V and has been automatically configured so that only the virtual switch is enabled on the adapter. DHCP and DNS work fine for all physical machines on the network. It also works for Virtual Machines running on another physical box. Virtual machines that are bound to the virtual switch network adapter are unable to get a IP address. If the virtual machine is given a static IP address with correct subnet, gateway and dns everything works. Has anyone else got this working?

  Read the article

• Must I have Exchange to use Blackberry Enterprise Server Express?

  - by John Spaz

  In the past I've setup BES (not express) for a company that just wanted their users on the corporate network, they didn't care for email or any other enterprise feature, they just wanted to push a policy that the phones internet should be routed through the corporate network. I want to setup BES Express now for a customer that also just wants the phones on his network but wherever I look, it says that BES Express requires Exchange. Is there a way to install BES Express without Exchange and without a AD Domain? Basically what the customer wants to accomplish is to be able to filter and log the internet access on the phones.

  Read the article

• Virtual Box Networking; How to configure bridged networking on Windows 7

  - by Krist van Besien

  I have VirtualBox on Windows 7. I have two virtual machines running RHEL, that work fine when the network is set to NAT. However I want to change the network adapters for the VM's to bridged in stead of NAT. However when I go in to the VM configuration, and select bridged I also need to select an adapter, but there is nothing to select. Apparently I need to install a separate driver/filter on the network adapter. However I don't know where to start. I reinstalled VirtualBox (latest version) but did not see an option to install such driver. What should I do?

  Read the article

• Wireless not working on desktop with Asus USB-N13 (B1) wireless adapter

  - by user900749

  I am trying to connect my desktop to a wireless network. I have purchased an ASUS USB-N13 B1 adapter. I have followed instructions for installing drivers and disabling conflicting drivers. I have thoroughly searched and could not find a solution. The adapter is recognized and powered on. I have entered the ssid and password information into the wireless network configuration. Other machines can connect to this wireless network, and the machine can connect online via ethernet without issue. Here is the output of some commands which summarize my configuration, and might give some clues : ~$ cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.1 LTS" ~$ uname -a Linux petra 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux ~$ lsusb Bus 001 Device 006: ID 0b05:17ab ASUSTek Computer, Inc. ~$ dmesg [ 1883.823150] wlan0: authenticate with 48:5b:39:e7:25:5e (try 1) [ 1884.020027] wlan0: authenticate with 48:5b:39:e7:25:5e (try 2) [ 1884.220025] wlan0: authenticate with 48:5b:39:e7:25:5e (try 3) [ 1884.420023] wlan0: authentication with 48:5b:39:e7:25:5e timed out Any assistance would be appreciated as I have been trying to get this machine online for several weeks now to no avail. Sincerely, Michael.

  Read the article

• Can't connect to wireless-n in dual mode.

  - by Tyllyn

  I recently purchased a Acer Aspire Revo AR3610-U9022. This little nettop uses a Atheros AR5B91 Wireless Network Adapter. I also have a Netgear RangeMax NEXT Wireless Route (model WNDR3300). I have been using this router in dual mode (11G and 11N) on my normal desktop without a problem (Mode: Up to 270Mbps at 5GHz & 54Mbps at 2.4 GHz), but doing this, my Revo won't detect the 11N network as being around... my desktop still does, but the Revo, nope... just the 11G. However, when I switch my router over to just "Up to 270Mbps at 2.4GHz", it kills the 11G entirely, but the Revo recognizes the 11N network. I'm a programmer by trade, and this hardware-y stuff confuses me more than it should. Is there any way that I could set this stuff up so my Revo can connect to the 11N part of my router, but keep the 11G around? :) Thanks!

  Read the article

• Setting up 802.1X wireless connection on OSX

  - by hizki

  I am an OSX user, I have Snow Leopard 10.6.5 and an updated AirPort. I am trying to connect to my university's wireless network, but it has a complex security that I am having trouble defining... Here there are instructions for connecting with Windows XP, Windows 7 and Linux. Can someone please instruct me what should I do to set up this network on my MAC? Thank you. P.S. I have had previous success in setting up this network, but I have no idea what I did that made it work. Since I updated my AirPort it worked only seldomly and very slowly... Before the update, even when it worked it never remembered my password.

  Read the article

• Nodes inside Cisco VPN. Incoming SSH requests allowed. But can't initiate an outbound SSH.

  - by Douglas Peter

  I've a gateway-to-gateway VPN setup between my Linksys RV042 router and a Cisco VPN. I am able to SSH into any of the machine inside the VPN from my network. But none of the machines inside the VPN can initiate an SSH into my network. It seems they've blocked even all ping requests to my network gateway. This is the requirement: I have scripts that SSH into the machines inside the VPN and run a long mysql query. The query generates an output to a file. The time that these queries take is variable. So I have a loop in my machine that periodically SSHes into the VPN machine and checks if the query has finished, and pulls the generated file using SCP. I need to simplify it thus: The script will run at the machine inside the VPN, and when the query completes, it will SSH into my machine and pushes the generated file. Thanks for any ideas.

  Read the article

< Previous Page | 250 251 252 253 254 255 256 257 258 259 260 261  | Next Page >