Search Results

Search found 19975 results on 799 pages for 'disk queue length'.

Page 259/799 | < Previous Page | 255 256 257 258 259 260 261 262 263 264 265 266  | Next Page >

• my LaCie 500 Gb not mounted on 11.10

  - by pooo

  My external USB drive was recognized with 10.x versions of Ubuntu but since 11.x I am getting stuck, I had tried everything I read in forums but still the same error: 4956.401052] usb 2-1.4: new high speed USB device number 14 using ehci_hcd [ 4956.539216] scsi14 : uas [ 4956.740955] scsi 14:0:0:0: Direct-Access LaCie Rugged FW USB3 1081 PQ: 0 ANSI: 4 [ 4963.256055] scsi 14:0:0:0: uas_eh_abort_handler tag 0 [ 4963.256076] scsi 14:0:0:0: uas_eh_device_reset_handler tag 0 [ 4963.256085] scsi 14:0:0:0: uas_eh_target_reset_handler tag 0 [ 4963.256091] scsi 14:0:0:0: uas_eh_bus_reset_handler tag 0 [ 4963.328122] usb 2-1.4: reset high speed USB device number 14 using ehci_hcd [ 4963.468743] scsi 14:0:0:0: Device offlined - not ready after error recovery [ 4963.468813] scsi 14:0:0:0: rejecting I/O to offline device [ 4963.468831] scsi 14:0:0:0: rejecting I/O to offline device [ 4963.469204] scsi 14:0:0:1: uas_sense_old: urb length 26 disagrees with IU sense data length 510, using 18 bytes of sense data [ 4963.512104] sd 14:0:0:0: Attached scsi generic sg3 type 0 [ 4994.253779] sd 14:0:0:0: uas_eh_abort_handler tag 0 [ 4994.253802] sd 14:0:0:0: uas_eh_device_reset_handler tag 0 [ 4994.253809] sd 14:0:0:0: uas_eh_target_reset_handler tag 0 [ 4994.253815] sd 14:0:0:0: uas_eh_bus_reset_handler tag 0 [ 4994.325880] usb 2-1.4: reset high speed USB device number 14 using ehci_hcd [ 4994.466488] sd 14:0:0:0: Device offlined - not ready after error recovery [ 4994.466555] sd 14:0:0:0: rejecting I/O to offline device [ 4994.466573] sd 14:0:0:0: rejecting I/O to offline device [ 4994.466582] sd 14:0:0:0: rejecting I/O to offline device [ 4994.466588] sd 14:0:0:0: [sdc] READ CAPACITY failed [ 4994.466593] sd 14:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 4994.466600] sd 14:0:0:0: [sdc] Sense not available. [ 4994.466608] sd 14:0:0:0: rejecting I/O to offline device [ 4994.466616] sd 14:0:0:0: [sdc] Write Protect is off [ 4994.466622] sd 14:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 4994.466629] sd 14:0:0:0: rejecting I/O to offline device [ 4994.466635] sd 14:0:0:0: [sdc] Asking for cache data failed [ 4994.466640] sd 14:0:0:0: [sdc] Assuming drive cache: write through [ 4994.467003] sd 14:0:0:0: [sdc] Attached SCSI disk if I am trying on an old ubuntu, the drive is mounted,

  Read the article

• responsibility for storage

  - by Stefano Borini

  A colleague and I were brainstorming about where to put the responsibility of an object to store itself on the disk in our own file format. There are basically two choices: object.store(file) fileformatWriter.store(object) The first one gives the responsibility of serialization on the disk to the object itself. This is similar to the approach used by python pickle. The second groups the representation responsibility on a file format writer object. The data object is just a plain data container (eventually with additional methods not relevant for storage). We agreed on the second methodology, because it centralizes the writing logic from generic data. We also have cases of objects implementing complex logic that need to store info while the logic is in progress. For these cases, the fileformatwriter object can be passed and used as a delegate, calling storage operations on it. With the first pattern, the complex logic object would instead accept the raw file, and implement the writing logic itself. The first method, however, has the advantage that the object knows how to write and read itself from any file containing it, which may also be convenient. I would like to hear your opinion before starting a rather complex refactoring.

  Read the article

• Installer doesn't display partition I want to install to

  - by Aditya

  While performing a Ubuntu 10.10 installation on my laptop, it doesn't show partitions pertaining to the PC. My PC configuration is as follows : HP Pavilion dv6 - 2020AX AMD Turion II Dual Core Mobile Processor M500 4 GB RAM OS Installed : Windows 7 500 GB Hard drive partitioned as follows : C : 227 GB (Free : 142 GB) D : 11.9 GB (Free : 1.98 GB) - Recovery F : 174 GB (Free : 18 GB) G : 50.5 GB (Free : 50.4 GB) So, I want to perform a Dual-boot installation on my PC, so that Ubuntu resides in the free disk space G:. Therefore, I started the Ubuntu 10.10 installation and select the manual partitioning feature in the installation. However, in the 'Allocate Drive Space' section of the installation, following partitions information is displayed: Partition Type Size Used /dev/sda /dev/sda1      1 MB    unknown /dev/sda2    ntfs    208 MB   unknown /dev/sda3   ntfs    244813 MB    168540 MB /dev/sda4    ntfs    255083 MB   3221 MB where /dev/sda - 500 GB So, what exactly is the problem? What is it should I do to install Ubuntu 10.10 in the G: disk space? Why are the partitions not being shown as the way they should be? Any Suggestions. Thank you for the help.

  Read the article

• Powershell variables to string

  - by Mike Koerner

  I'm new to powershell. I'm trying to write an error handler to wrap around my script.  Part of the error handler is dumping out some variable settings.  I spent a while trying to do this and couldn't google a complete solution so I thought I'd post something. I want to display the $myinvocation variable. In powershell you can do this PS C:\> $myInvocation for my purpose I want to create a stringbuilder object and append the $myinvocation info.  I tried this $sbOut = new-object System.Text.Stringbuilder $sbOut.appendLine($myinvocation) $sbOut.ToString() This produces                                    Capacity                                MaxCapacity                                     Length                                    --------                                -----------                                     ------                                          86                                 2147483647                                         45 System.Management.Automation.InvocationInfo This is not what I wanted so I tried $sbOut.appendLine(($myinvocation|format-list *)) This produced                                    Capacity                                MaxCapacity                                     Length                                    --------                                -----------                                     ------                                         606                                 2147483647                                        305 Microsoft.PowerShell.Commands.Internal.Format.FormatStartData Microsoft.PowerShell.Commands.Internal.Format.GroupStartData Micros oft.PowerShell.Commands.Internal.Format.FormatEntryData Microsoft.PowerShell.Commands.Internal.Format.GroupEndData Microsoft.Powe rShell.Commands.Internal.Format.FormatEndData Finally I figured out how to produce what I wanted: $sbOut = new-object System.Text.Stringbuilder [void]$sbOut.appendLine(($myinvocation|out-string)) $sbOut.ToString() MyCommand        : $sbOut = new-object System.Text.Stringbuilder                                    [void]$sbOut.appendLine(($myinvocation|out-string))                                      $sbOut.ToString()                    BoundParameters  : {} UnboundArguments : {} ScriptLineNumber : 0 OffsetInLine     : 0 HistoryId        : 13 ScriptName       : Line             : PositionMessage  : InvocationName   : PipelineLength   : 2 PipelinePosition : 1 ExpectingInput   : False CommandOrigin    : Runspace Note the [void] in front of the stringbuilder variable doesn't show the Capacity,MaxCapacity of the stringbuilder object.  The pipe to out-string makes the output a string. It's not pretty but it works.

  Read the article

• Using Shader causes triangle to disappear

  - by invisal

  The following is my rendering code. Private Sub GameRender() GL.Clear(ClearBufferMask.ColorBufferBit + ClearBufferMask.DepthBufferBit) GL.ClearColor(Color.SkyBlue) GL.UseProgram(theProgram) GL.EnableClientState(ArrayCap.VertexArray) GL.EnableClientState(ArrayCap.ColorArray) GL.BindBuffer(BufferTarget.ArrayBuffer, vertexPositionID) GL.DrawArrays(BeginMode.Triangles, 0, 3) GL.DisableClientState(ArrayCap.ColorArray) GL.DisableClientState(ArrayCap.VertexArray) GlControl1.SwapBuffers() End Sub This is screenshot without GL.UseProgram(theProgram) This is screenshot with GL.UseProgram(theProgram) Here are my shader code that I picked from online tutorial. Vertex Shader #version 330 layout(location = 0) in vec4 position; void main() { gl_Position = position; } Fragment Shader #version 330 out vec4 outputColor; void main() { outputColor = vec4(1.0f, 1.0f, 1.0f, 1.0f); } These are my shader creation code. '' Initialize Shader Dim shaderList(1) As Integer shaderList(0) = CreateShader(ShaderType.VertexShader, strVertexShader) shaderList(1) = CreateShader(ShaderType.FragmentShader, strFragShader) theProgram = CreateProgram(shaderList) GL.DeleteShader(shaderList(0)) GL.DeleteShader(shaderList(1)) Here are my helper functions Private Function CreateShader(ByVal shaderType As ShaderType, ByVal code As String) Dim shader As Integer = GL.CreateShader(shaderType) GL.ShaderSource(shader, code) GL.CompileShader(shader) Dim status As Integer GL.GetShader(shader, ShaderParameter.CompileStatus, status) If status = False Then MsgBox(GL.GetShaderInfoLog(shader)) End If Return shader End Function Private Function CreateProgram(ByVal shaderList() As Integer) As Integer Dim program As Integer = GL.CreateProgram() For i As Integer = 0 To shaderList.Length - 1 GL.AttachShader(program, shaderList(i)) Next GL.LinkProgram(program) Dim status As Integer GL.GetProgram(program, ProgramParameter.LinkStatus, status) If status = False Then MsgBox(GL.GetProgramInfoLog(program)) End If For i As Integer = 0 To shaderList.Length - 1 GL.DetachShader(program, shaderList(i)) Next Return program End Function

  Read the article

• Can I use all my RAM for application data?

  - by gsedej

  Hi! I have yet another question about "where is my Linux memory" Question goes: can I use cache for application data? On my laptop I have 1GB ram. Situation after some time of work: browser takes 400MB and all other apps caa 300MB (quickly summed in system monitor). System monitor says I use 90% of RAM and I have already 200MB on swap. Laptop is getting slower when I start new things (e.g. open new tab in browser or open new Nautilus window). probably putting memory on swap So there should be 1200MB (ram+swap) used but all app I see uses only 600MB. Where are other 600MB? Out of this 600MB there is 400MB real RAM. I am not copying or any other massive IO activity. I read about Linux smartly uses all ram it has using buffers and cache. So, kernel (cache) uses 300MB. What if I don't want to have disk mirrored and I want to use memory for application data (e.g. new browser tab)? I don't need 200MB of mirrored disk data, because I (for example) won't use open the same photos on data partition I just seen. So can I use all my RAM for application data? (including browser, desktop, xorg, other services). How?

  Read the article

• Junit test bluej [closed]

  - by user1721929

  Can someone make a junit test of this? public class PersonName { int NumberNames(String wholename) { // store the name passed in to the method String testname=wholename; // initialize number of names found int numnames=0; // on each iteration remove one name while(testname.length()>numnames) { // take the "white space" from the beginning and end testname = testname.trim(); // determine the position of the first blank // .. end of the first word int posBlank= testname.indexOf(' '); // cut off word /** * it continues to the stop sign because that is where you commanded it to end */ testname=testname.substring(posBlank+1,testname.length()); // System.out.println(numnames); // System.out.println(testname); numnames++; System.out.println(testname); } return numnames; } public static void main(String args[]) { PersonName One= new PersonName(); System.out.println(One.NumberNames("Bobby")); System.out.println(One.NumberNames("Bobby Smith")); System.out.println(One.NumberNames("Bobby L. Smith")); System.out.println(One.NumberNames(" Bobby Paul Smith Jr. ")); } }

  Read the article

• How can I convince my boss to invest into the developer environment?

  - by user95291

  Our boss said that developers should have fewer mistakes so the company would have money for displays, servers etc. An always mentioned example is a late firing of an underperforming colleague whose salary would have covered some of these expenses. On the other hand it happened a few times that it took a few days to free up some disk space on our servers since we can't get any more disk. The cost of mandays was definitely higher than the cost of a new HDD. Another example is that we use 14-15" notebooks for development and most of the developers get external displays after they spent one year at the company. The price of a 22-24" display is just a small fraction of a developers annual salary. Devs say that they like the company because of other reasons (high quality code, interesting projects etc.) but this kind of issues not just simply time-consuming but also demotivate them. In the point of view of the developers it seems that the boss always can find an issue in the past which they could have been done better so it's pointless to work better to get for a second display/HDD/whatever. How can I convince my boss to invest more into development environment? Is it possible to break this endless loop?

  Read the article

• arm-none-ebai-gcc does not work from mounted directory

  - by dmytro_lviv

  I want to build project for ARM micro controller. For this purpose in folder with project was placed script, which download toolchain and build him. After run this script toolchain was placed in folder with project. Folder with project placed on another logical disk (which shared between Win and Linux) and this disk is mounting each time when I start develop. (Mount by hand). When I start make, in terminal I receive error: make[3]: arm-none-eabi-gcc: Command not found The output from echo $PATH: /mnt/Smoothie-master/gcc-arm-none-eabi/bin:/usr/lib/lightdm/lightdm:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games The output from whereis arm-none-ebai-gcc: arm-none-ebai-gcc: All binaries files, which are relating to this toolchain are placed in the next directory: /mnt/Smoothie-master/gcc-arm-none-eabi/bin/ and has permissions: "-rwxrwxrwx" Before building this toolchain, I had another similar toolchain (another version of this), but installed through apt-get. And it was removed through apt-get before building new. Where is the problem? Thanks!

  Read the article

• How to determine where on a path my object will be at a given point in time?

  - by Dave

  I have map and an obj that is meant to move from start to end in X amount of time. The movements are all straight lines, as curves are beyond my ability at the moment. So I am trying to get the object to move from these points, but along the way there are way points which keep it on a given path. The speed of the object is determined by how long it will take to get from start to end (based on X). This is what i have so far: //get_now() returns seconds since epoch var timepassed = get_now() - myObj[id].start; //seconds since epoch for departure var timeleft = myObj[id].end - get_now(); //seconds since epoch for arrival var journey_time = 60; //this means 60 minutes total journey time var array = [[650,250]]; //way points along the straight paths if(step == 0 || step =< array.length){ var destinationx = array[step][0]; var destinationy = array[step][1]; }else if( step == array.length){ var destinationx = 250; var destinationy = 100; } else { var destinationx = myObj[id].startx; var destinationy = myObj[id].starty; } step++; When the user logs in at any given time, the object needs to be drawn in the correct place of the path, almost as if its been travelling along the path whilst the user has not been at the PC with the available information i have above. How do I do this? Note: The camera angle in the game is a birds eye view so its a straight forward X:Y rather than isometric angles.

  Read the article

• usb wifi dongle on ubuntu server, cannot install realtek driver RTL 8188cus

  - by Sandro Dzneladze

  I got cheap Ebay wifi dongle from HongKong, Im trying to set it up on my ubuntu server. Occasionally need to move server, so it cannot always be connected to router via lan. Anyhow, usb wifi came with a driver cd. I uploaded files to my home directory and tried to run install script (RTL 8188cus): sudo bash install.sh But I get error: Authentication requested [root] for make driver: make ARCH=x86_64 CROSS_COMPILE= -C /lib/modules/2.6.38-8-server/build M=/home/minime/RTL 8188cus/Linux/driver/rtl8192CU_linux_v2.0.1324.20110126 modules make[1]: Entering directory `/usr/src/linux-headers-2.6.38-8-server' make[1]: *** No rule to make target `8188cus/Linux/driver/rtl8192CU_linux_v2.0.1324.20110126'. Stop. make[1]: Leaving directory `/usr/src/linux-headers-2.6.38-8-server' make: *** [modules] Error 2 Compile make driver error: 2, Please check error Mesg Any ideas what Im doing wrong? There is another driver folder for linux called: RTL 81XX, which doesn't have install.sh at all! I tried to use make command, but I get: make: *** No targets specified and no makefile found. Stop. Any help? this is first time I'm installing driver from source. Im on Ubuntu 11.04 server. lsusb Bus 001 Device 002: ID 0bda:8176 Realtek Semiconductor Corp. lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation N10 Family DMI Bridge [8086:a000] (rev 02) 00:02.0 VGA compatible controller [0300]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a001] (rev 02) 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02) 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02) 00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) 00:1d.1 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) 00:1d.2 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) 00:1d.3 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) 00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) 00:1f.2 IDE interface [0101]: Intel Corporation N10/ICH7 Family SATA IDE Controller [8086:27c0] (rev 02) 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02) 01:00.0 Ethernet controller [0200]: Atheros Communications Device [1969:1083] (rev c0) sudo lshw description: Desktop Computer product: To Be Filled By O.E.M. (To Be Filled By O.E.M.) vendor: To Be Filled By O.E.M. version: To Be Filled By O.E.M. serial: To Be Filled By O.E.M. width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall64 vsyscall32 configuration: boot=normal chassis=desktop family=To Be Filled By O.E.M. sku=To Be Filled By O.E.M. uuid=00020003-0004-0005-0006-000700080009 *-core description: Motherboard product: AD525PV3 vendor: ASRock physical id: 0 *-firmware description: BIOS vendor: American Megatrends Inc. physical id: 0 version: P1.20 date: 04/01/2011 size: 64KiB capacity: 448KiB capabilities: pci upgrade shadowing cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot zipboot biosbootspecification netboot *-cpu description: CPU product: Intel(R) Atom(TM) CPU D525 @ 1.80GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: Intel(R) Atom(TM) CPU D525 @ 1.80GHz serial: To Be Filled By O.E.M. slot: CPUSocket size: 1800MHz capacity: 1800MHz width: 64 bits clock: 200MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl tm2 ssse3 cx16 xtpr pdcm movbe lahf_lm configuration: cores=2 enabledcores=2 threads=4 *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 48KiB capacity: 48KiB capabilities: internal write-back data *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 1MiB capacity: 1MiB capabilities: internal write-back unified *-memory description: System Memory physical id: c slot: System board or motherboard size: 2GiB *-bank:0 description: SODIMM DDR2 Synchronous 800 MHz (1.2 ns) product: ModulePartNumber00 vendor: Manufacturer00 physical id: 0 serial: SerNum00 slot: DIMM0 size: 2GiB width: 64 bits clock: 800MHz (1.2ns) *-bank:1 description: DIMM [empty] product: ModulePartNumber01 vendor: Manufacturer01 physical id: 1 serial: SerNum01 slot: DIMM1 *-pci description: Host bridge product: N10 Family DMI Bridge vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 02 width: 32 bits clock: 33MHz configuration: driver=agpgart-intel resources: irq:0 *-display description: VGA compatible controller product: N10 Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:41 memory:fea80000-feafffff ioport:dc00(size=8) memory:e0000000-efffffff memory:fe900000-fe9fffff *-multimedia description: Audio device product: N10/ICH 7 Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 02 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:43 memory:fea78000-fea7bfff *-pci:0 description: PCI bridge product: N10/ICH 7 Family PCI Express Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: 02 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:e000(size=4096) memory:feb00000-febfffff ioport:80000000(size=2097152) *-network description: Ethernet interface product: Atheros Communications vendor: Atheros Communications physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: c0 serial: XX size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.99 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:42 memory:febc0000-febfffff ioport:ec00(size=128) *-usb:0 description: USB Controller product: N10/ICH 7 Family USB UHCI Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:23 ioport:d880(size=32) *-usb:1 description: USB Controller product: N10/ICH 7 Family USB UHCI Controller #2 vendor: Intel Corporation physical id: 1d.1 bus info: pci@0000:00:1d.1 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:19 ioport:d800(size=32) *-usb:2 description: USB Controller product: N10/ICH 7 Family USB UHCI Controller #3 vendor: Intel Corporation physical id: 1d.2 bus info: pci@0000:00:1d.2 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:18 ioport:d480(size=32) *-usb:3 description: USB Controller product: N10/ICH 7 Family USB UHCI Controller #4 vendor: Intel Corporation physical id: 1d.3 bus info: pci@0000:00:1d.3 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:16 ioport:d400(size=32) *-usb:4 description: USB Controller product: N10/ICH 7 Family USB2 EHCI Controller vendor: Intel Corporation physical id: 1d.7 bus info: pci@0000:00:1d.7 version: 02 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:fea77c00-fea77fff *-pci:1 description: PCI bridge product: 82801 Mobile PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: e2 width: 32 bits clock: 33MHz capabilities: pci subtractive_decode bus_master cap_list *-isa description: ISA bridge product: NM10 Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 02 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-ide description: IDE interface product: N10/ICH7 Family SATA IDE Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 version: 02 width: 32 bits clock: 66MHz capabilities: ide pm bus_master cap_list emulated configuration: driver=ata_piix latency=0 resources: irq:19 ioport:1f0(size=8) ioport:3f6 ioport:170(size=8) ioport:376 ioport:ff90(size=16) memory:80200000-802003ff *-disk description: ATA Disk product: WDC WD10TPVT-11U vendor: Western Digital physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 01.0 serial: WD-WXC1A80P0314 size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=00088c47 *-volume:0 description: EXT4 volume vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 logical name: /media/private version: 1.0 serial: 042daf2d-350c-4640-a76a-4554c9d98c59 size: 300GiB capacity: 300GiB capabilities: primary journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2011-11-06 11:05:03 filesystem=ext4 label=Private lastmountpoint=/media/private modified=2012-04-13 20:01:16 mount.fstype=ext4 mount.options=rw,relatime,barrier=1,stripe=1,data=ordered mounted=2012-04-13 20:01:16 state=mounted *-volume:1 description: Extended partition physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 size: 625GiB capacity: 625GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux filesystem partition physical id: 5 logical name: /dev/sda5 logical name: /media/storage capacity: 600GiB configuration: mount.fstype=ext4 mount.options=rw,relatime,barrier=1,stripe=1,data=ordered state=mounted *-logicalvolume:1 description: Linux filesystem partition physical id: 6 logical name: /dev/sda6 logical name: /media/dropbox capacity: 24GiB configuration: mount.fstype=ext4 mount.options=rw,relatime,barrier=1,stripe=1,data=ordered state=mounted *-volume:2 description: EXT4 volume vendor: Linux physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 logical name: /media/www version: 1.0 serial: 9b0a27b4-05d8-40d5-bfc7-4aeba198db7b size: 2570MiB capacity: 2570MiB capabilities: primary journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2011-11-06 11:05:11 filesystem=ext4 label=www lastmountpoint=/media/www modified=2012-04-15 11:31:12 mount.fstype=ext4 mount.options=rw,relatime,barrier=1,stripe=1,data=ordered mounted=2012-04-15 11:31:12 state=mounted *-volume:3 description: Linux swap volume physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 version: 1 serial: 6ed1130e-3aad-4fa6-890b-77e729121e3b size: 4098MiB capacity: 4098MiB capabilities: primary nofs swap initialized configuration: filesystem=swap pagesize=4096 *-serial UNCLAIMED description: SMBus product: N10/ICH 7 Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 02 width: 32 bits clock: 33MHz configuration: latency=0 resources: ioport:400(size=32) *-scsi physical id: 1 bus info: usb@1:4 logical name: scsi2 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk description: SCSI Disk physical id: 0.0.0 bus info: scsi@2:0.0.0 logical name: /dev/sdb size: 3864MiB (4051MB) capabilities: partitioned partitioned:dos configuration: signature=000b4c55 *-volume description: EXT4 volume vendor: Linux physical id: 1 bus info: scsi@2:0.0.0,1 logical name: /dev/sdb1 logical name: / version: 1.0 serial: 33926e39-4685-4f63-b83c-f2a67824b69a size: 3862MiB capacity: 3862MiB capabilities: primary bootable journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2011-10-11 14:03:46 filesystem=ext4 lastmountpoint=/ modified=2012-03-19 11:47:29 mount.fstype=ext4 mount.options=rw,noatime,errors=remount-ro,barrier=1,data=ordered mounted=2012-04-15 11:31:11 state=mounted rfkill list all Doesnt show anything! dmesg | grep -i firmware [ 0.715481] pci 0000:00:1f.0: [Firmware Bug]: TigerPoint LPC.BM_STS cleared

  Read the article

• How can I install oracle-java7 from webupd8 ppa?

  - by Ahmed Zain El Dein

  I installed ppa:webupd8team/java and I get the following error Output from: sudo apt-get install oracle-java7-installer Reading package lists... Done Building dependency tree Reading state information... Done Suggested packages: binfmt-support visualvm ttf-baekmuk ttf-unfonts ttf-unfonts-core ttf-kochi-gothic ttf-sazanami-gothic ttf-kochi-mincho ttf-sazanami-mincho ttf-arphic-uming The following packages will be upgraded: oracle-java7-installer 1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 1 not fully installed or removed. Need to get 0 B/16.0 kB of archives. After this operation, 64.5 kB of additional disk space will be used. Could not exec dpkg! E: Sub-process /usr/bin/dpkg returned an error code (100) i did afterwords those line of code trying to resolve the issue becuase it is not existed actually in the /usr/bin/dpkg there is no dpkg mkdir /tmp/dpkg cd /tmp/dpkg wget http://archive.ubuntu.com/ubuntu/pool/main/d/dpkg/dpkg_1.15.5.6ubuntu4_i386.deb ar x dpkg*.deb data.tar.gz tar xfvz data.tar.gz ./usr/bin/dpkg sudo cp ./usr/bin/dpkg /usr/bin/ sudo apt-get update sudo apt-get install --reinstall dpkg then i get this $ sudo apt-get install --reinstall dpkg Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 1 reinstalled, 0 to remove and 6 not upgraded. 1 not fully installed or removed. Need to get 0 B/1,814 kB of archives. After this operation, 0 B of additional disk space will be used. dpkg: warning: 'dpkg-deb' not found on PATH. dpkg: 1 expected program(s) not found on PATH. NB: root's PATH should usually contain /usr/local/sbin, /usr/sbin and /sbin. E: Sub-process /usr/bin/dpkg returned an error code (2) How can I fix this?

  Read the article

• Why does Eclipse keep crashing and dpkg erroring out?

  - by Sanju Sony Kurian

  I AM GETTING THE ERROR E: Sub-process /usr/bin/dpkg returned an error code (1) WHILE I WAS TRYING TO UPGRADE MY PC. i USE ECLIPSE AND IT KEEPS ON CRASHING... pLEASE HELP I ATTACH THE ERROR sanju@sanju-Dell-System-XPS-L502X:~$ upgrade Reading package lists... Done Building dependency tree Reading state information... Done The following packages have been kept back: aisleriot gir1.2-rb-3.0 gir1.2-totem-1.0 gnome-disk-utility gnome-keyring libgck-1-0 libgcr-3-1 libtotem0 linux-generic linux-headers-generic linux-image-generic rhythmbox rhythmbox-data rhythmbox-mozilla rhythmbox-plugin-cdrecorder rhythmbox-plugin-magnatune rhythmbox-plugin-zeitgeist rhythmbox-plugins seahorse totem totem-common totem-mozilla totem-plugins 0 upgraded, 0 newly installed, 0 to remove and 23 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? Y Setting up grub-pc (1.99-21ubuntu3.1) ... /var/lib/dpkg/info/grub-pc.config: 35: /etc/default/grub: Syntax error: EOF in backquote substitution dpkg: error processing grub-pc (--configure): subprocess installed post-installation script returned error exit status 2 Errors were encountered while processing: grub-pc E: Sub-process /usr/bin/dpkg returned an error code (1)

  Read the article

• Installer gets stuck with a grayed out forward button.

  - by TRiG

  I have a CD with Ubuntu 10.10 and a laptop with Ubuntu 8.10. The laptop had all sorts of crud on it, and anything I wanted to keep was backed up on an external drive, so I was happy to do a wipe and reinstall instead of an update. So after a bit of faffing about trying to work out how to get the thing to boot from the CD drive, I did that. So the screen comes up with the choice: the options are Try Ubuntu and Install Ubuntu. I choose to install and to overwrite my current installation. So far so good. I then get a progress bar labelled something like copying files (I forget the exact wording) and further options to fill in for my location, keyboard locale, username and password. On each of these screens there are forward and back buttons. On the last screen (password), the forward button is greyed out. Well, I think to myself, no doubt it will become active when that copying files progress bar completes. The progress bar never completes. It hangs. And the label changes from copying files to the chirpy ready when you are. The forward button remains greyed out. The back button is as unhelpful as you'd expect it to be. And there's nothing else to click. We have reached an impasse. I tried restarting the laptop, to test whether it actually was properly installed. It wasn't. I tried to run Ubuntu live from the CD, to test whether the disk was damaged. That wouldn't work either, but I suspect it's just because the laptop is old and has a slow disk drive. I'm typing this question on another computer using the Ubuntu live CD and it's working fine. So there's nothing wrong with the CD.

  Read the article

• Input signal out of range; Change settings to 1600 x 900

  - by Clayton

  I recently installed Ubuntu 12.04 onto my HP Pavilion, in an attempt to make the desktop able to dual-boot Windows 7 and Ubuntu. I managed to get down to the last step, and finished the installation process. After it prompted me to remove what I used to install Ubuntu, I did so, removing my SanDisk 8GB flash drive, and allowed the system to reboot. Like usual, the desktop booted with the HP image, with the options at the bottom(Boot Menu, System Recovery, etc). However, when it should have started up with Ubuntu(like I'm certain it should have done), I received the following error: Input signal out of range Change settings to 1600 x 900 From the time I installed the operating system, back in late August, till now, I've been trying to figure out how I would go about fixing this issue. My mom is also starting to get frustrated with my not having resolved the issue, as its the only desktop that has a printer installed. Is there any possible way to resolve this? To summarize the problem: -Successful boot -Screen brings up error -Screen goes to standby -Nothing else possible until desktop is rebooted, which will initiate the above three steps A few notes: -I did not back up my computer before I installed Ubuntu. I didn't have anything to write to, and basically just forgot to. : -I don't have a Recovery Disk. -I don't have the Windows 7 disk that is supposed to come with the computer. -It has been narrowed down by a friend on Skype that the problem lies with the display, and that the vga= boot command does have something to do with fixing the problem Thank you in advance for resolving this problem. I greatly appreciate it. ^^

  Read the article

• F# Simple Twitter Update

  - by mroberts

  A short while ago I posted some code for a C# twitter update.  I decided to move the same functionality / logic to F#.  Here is what I came up with. 1: namespace Server.Actions 2:   3: open System 4: open System.IO 5: open System.Net 6: open System.Text 7:   8: type public TwitterUpdate() = 9: 10: //member variables 11: [<DefaultValue>] val mutable _body : string 12: [<DefaultValue>] val mutable _userName : string 13: [<DefaultValue>] val mutable _password : string 14:   15: //Properties 16: member this.Body with get() = this._body and set(value) = this._body <- value 17: member this.UserName with get() = this._userName and set(value) = this._userName <- value 18: member this.Password with get() = this._password and set(value) = this._password <- value 19:   20: //Methods 21: member this.Execute() = 22: let login = String.Format("{0}:{1}", this._userName, this._password) 23: let creds = Convert.ToBase64String(Encoding.ASCII.GetBytes(login)) 24: let tweet = Encoding.ASCII.GetBytes(String.Format("status={0}", this._body)) 25: let request = WebRequest.Create("http://twitter.com/statuses/update.xml") :?> HttpWebRequest 26: 27: request.Method <- "POST" 28: request.ServicePoint.Expect100Continue <- false 29: request.Headers.Add("Authorization", String.Format("Basic {0}", creds)) 30: request.ContentType <- "application/x-www-form-urlencoded" 31: request.ContentLength <- int64 tweet.Length 32: 33: let reqStream = request.GetRequestStream() 34: reqStream.Write(tweet, 0, tweet.Length) 35: reqStream.Close() 36:   37: let response = request.GetResponse() :?> HttpWebResponse 38:   39: match response.StatusCode with 40: | HttpStatusCode.OK -> true 41: | _ -> false   While the above seems to work, it feels to me like it is not taking advantage of some functional concepts.  Love to get some feedback as to how to make the above more “functional” in nature.  For example, I don’t like the mutable properties.

  Read the article

• Webserver not giving the correct response on CURL and other httprequest methods [migrated]

  - by Maxim

  I am trying to make a REST request to a external webserver by using this code <?php $user = 'USER'; $pass = 'PASS'; $data = "MYDATA" $ch = curl_init('URL'); curl_setopt($ch, CURLOPT_POST, true); curl_setopt($ch, CURLOPT_RETURNTRANSFER, true); curl_setopt($ch, CURLOPT_POSTFIELDS, $data); curl_setopt($ch, CURLOPT_HTTPHEADER, array( 'Content-Type: application/json', 'Content-Length: ' . strlen($data)) ); curl_setopt($ch, CURLOPT_SSL_VERIFYPEER, false); curl_setopt($ch, CURLOPT_VERBOSE, true); if(!($res = curl_exec($ch))) { echo('[cURL Failure] ' . curl_error($ch)); } curl_close($ch); echo($res); Now this is a CURL request, however i tried different methods to test my result and they all give me a 403 forbidden error response that i get from the webserver, however i do get a 200 response when i run it on any other webserver (localhost, webserver2, ...) Therefore i think there is something wrong with my webserver and it might be disallowing/caching the post parameters that i provide because sometimes it returns a 200 response but most of the times it returns the 403. This is the response i get : HTTP/1.1 403 Forbidden Accept-Ranges: bytes Content-Type: application/json; charset=UTF-8 Date: Sat, 26 Oct 2013 13:56:37 GMT Server: Restlet-Framework/2.1.3 Vary: Accept-Charset, Accept-Encoding, Accept-Language, Accept Content-Length: 77 Connection: keep-alive {"error":"ForbiddenOperationException","errorMessage":"Invalid credentials."} It says Invalid credentials however i provide the correct credentials and i can confirm them because it is working on other servers. Since this is a crucial part of my script that i use for clients to register i assume that there is something wrong with the post parameters. I am running cpanel and uninstalled the following already: - varnish - apachebooster i also recompiled php already and enabled curl and its dependencies but nothing seems to resolve my problem. If more information is required then don't hesitate to ask me in the comments i will respond very quickly as i really need this. any help is appreciated. Kind regards Maxim

  Read the article

• cannot mount root filesystem on 10.04

  - by howaryoo

  I tried to apply the recommendation of question: Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) After running that command: sudo mount --bind /dev /mnt/dev I get this error message: mount: mount point /mnt/dev does not exist fdisk -l returns /dev/sda1 /dev/sda2 /dev/sda5 do I need to mount sda2 and sda5? Edited after @psusi's comment: /dev/sda1 is the boot file system It seems that I need to mount sda2 or sda5. Here is what I tried: (I tried this on a virtual machine so the sda(s) are now vda(s) ) ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/vda: 19.3 GB, 19327352832 bytes 16 heads, 63 sectors/track, 37449 cylinders Units = cylinders of 1008 * 512 = 516096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0008eece Device Boot Start End Blocks Id System /dev/vda1 * 3 496 248832 83 Linux Partition 1 does not end on cylinder boundary. /dev/vda2 498 37448 18622465 5 Extended Partition 2 does not end on cylinder boundary. /dev/vda5 498 37448 18622464 8e Linux LVM ubuntu@ubuntu:~$ ubuntu@ubuntu:~$ ubuntu@ubuntu:~$ sudo mount -t ext4 /dev/vda5 /mnt mount: wrong fs type, bad option, bad superblock on /dev/vda5, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so ubuntu@ubuntu:~$ sudo mount -t ext2 /dev/vda5 /mnt mount: wrong fs type, bad option, bad superblock on /dev/vda5, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so ubuntu@ubuntu:~$ Any info that can help me rescue that server would be greatly appreciated!

  Read the article

• To encryption=on or encryption=off a simple ZFS Crypto demo

  - by darrenm

  I've just been asked twice this week how I would demonstrate ZFS encryption really is encrypting the data on disk.  It needs to be really simple and the target isn't forensics or cryptanalysis just a quick demo to show the before and after. I usually do this small demo using a pool based on files so I can run strings(1) on the "disks" that make up the pool. The demo will work with real disks too but it will take a lot longer (how much longer depends on the size of your disks).  The file hamlet.txt is this one from gutenberg.org # mkfile 64m /tmp/pool1_file # zpool create clear_pool /tmp/pool1_file # cp hamlet.txt /clear_pool # grep -i hamlet /clear_pool/hamlet.txt | wc -l Note the number of times hamlet appears # zpool export clear_pool # strings /tmp/pool1_file | grep -i hamlet | wc -l Note the number of times hamlet appears on disk - it is 2 more because the file is called hamlet.txt and file names are in the clear as well and we keep at least two copies of metadata. Now lets encrypt the file systems in the pool. Note you MUST use a new pool file don't reuse the one from above. # mkfile 64m /tmp/pool2_file # zpool create -O encryption=on enc_pool /tmp/pool2_file Enter passphrase for 'enc_pool': Enter again: # cp hamlet.txt /enc_pool # grep -i hamlet /enc_pool/hamlet.txt | wc -l Note the number of times hamlet appears is the same as before # zpool export enc_pool # strings /tmp/pool2_file | grep -i hamlet | wc -l Note the word hamlet doesn't appear at all! As a said above this isn't indended as "proof" that ZFS does encryption properly just as a quick to do demo.

  Read the article

• Restoring GRUB2 on Software RAID 0 after Windows 7 wiped it using LiveCD

  - by unknownthreat

  I have installed Ubuntu 10.10 on my system. However, I need to install Windows 7 back, and I expect that it would alter GRUB and it did. Right now, my partition on my Software RAID 0 looks like this: nvidia_acajefec1 is Ubuntu 10.10 and nvidia_acajefec3 is Windows 7. I've been following some guides around and I am always stuck at GRUB not able to detect the usual RAID content. I've tried running: sudo grub > root (hd0,0) GRUB complains it couldn't find my hard disk. So I tried: find (hd0,0) And it complains that it couldn't find anything. So I tried: find /boot/grub/stage1 It said "file not found". Here's the text from the console: ubuntu@ubuntu:~$ grub Probing devices to guess BIOS drives. This may take a long time. [ Minimal BASH-like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a device/filename. ] grub> root (hd0,0) root (hd0,0) Error 21: Selected disk does not exist grub> find /boot/grub/stage1 find /boot/grub/stage1 Error 15: File not found Fortunately, I got one person suggesting that what I've been trying to do is for GRUB Legacy, not GRUB2. So I went to the suggested website, ** (http://grub.enbug.org/Grub2LiveCdInstallGuide) **try to look around, and try: ubuntu@ubuntu:~$ sudo fdisk -l Unable to seek on /dev/sda This is just the step 2 of the instruction in the http://grub.enbug.org/Grub2LiveCdInstallGuide and I cannot proceed because it cannot seek /dev/sda. However, ubuntu@ubuntu:~$ sudo dmraid -r /dev/sdb: nvidia, "nvidia_acajefec", stripe, ok, 488397166 sectors, data@ 0 /dev/sda: nvidia, "nvidia_acajefec", stripe, ok, 488397166 sectors, data@ 0 So what now? Do you have an idea for how to make fdisk see my RAID array on live cd (Ubuntu 10.10)? Honestly, I am lost, very lost in trying to restore GRUB2 on this software RAID 0 system right now.

  Read the article

• Booting Ubuntu 12.04 in Unity the Windows Theme & Icon Theme reversed back to and always locked to Ubuntu default

  - by Antonio

  I did set up last year Faience-Ocre as my Icon Theme and Adwaita Cupertino L Unity as my Windows Theme (the GTK+ thme was unchanged to Adwaita (default)). It has worked perfectly well until 3 days ago when starting my PC I saw the Ubuntu default showing up for Windows & Icon Theme. I noticed that at start-up the disk access LED is not lit up continuously as before but at moment stops reading for a few seconds (up to 15 s) then complete the disk reading process. When all was working well this LED would lit up continuously. Another thing is that GNOME applications are as well not working well as previously Nautilus and Gedit now don't use the global menu in the system bar but a local window menu. Nautilus - Nemo before the incident Nautilus - Nemo now ... I did open dconf to check the desktop settings in org-gnome-desktop-wm-preferences and everything is looking good. When I change the settings in the app Advanced Settings in the Theme folder I see the respective value changing in dconf. However, there is no change on my desktop. It looks like it's crippled and GNOME related. [Update 1]: I have the same defect as referenced @ ubuntu theme suddenly changed to default and it's not coming back! instead of my GTK theme I get a classic, Windows-95-like grayish theme ... However one of the solution mentionned: http://www.webupd8.org/2011/06/fix-ubuntu-linux-mint-theme-changing-to.html is not working at all, even for 20 s up to 60 s delay.

  Read the article

• Do you have a contract between the Product Owner and the Team?

  - by Martin Hinshelwood

  Working in Scrum it is useful to define a Sprint Contract between the Product Owner (PO) and the implementation Team. Doing this helps to improve common understanding in, and sometimes to enforce, the relationship between the PO and the Team. This is simply an agreement between the PO for one Sprint and is not really a commercial contract and should be confirmed via an e-mail at the beginning of every Sprint. “The implementation team agrees to do its best to deliver an agreed on set of features (scope) to a defined quality standard by the end of the sprint. (Ideally they deliver what they promised, or even a bit more.) The Product Owner agrees not to change his instructions before the end of the Sprint.” - Agile Project management (http://agilesoftwaredevelopment.com/blog/peterstev/10-agile-contracts#Sprint) Each of the Sprints in a Scrum project can be considered a mini-project that has Time (Sprint Length), Scope (Sprint Backlog), Quality (Definition of Done) and Cost (Team Size*Sprint Length). Only the scope can vary and this is measured every sprint. Figure: Good Example, the product owner should reply to the team and commit to the contract This Rule has been added to SSW’s Rules to better Scrum with TFS   Technorati Tags: SSW,Scrum,SSW Rules

  Read the article

• One-week release cycle: how do I make this feasible?

  - by Arkaaito

  At my company (3-yr-old web industry startup), we have frequent problems with the product team saying "aaaah this is a crisis patch it now!" (doesn't everybody?) This has an impact on the productivity (and morale) of engineering staff, self included. Management has spent some time thinking about how to reduce the frequency of these same-day requests and has come up with the solution that we are going to have a release every week. (Previously we'd been doing one every two weeks, which usually slipped by a couple of days or so.) There are 13 developers and 6 local / 9 offshore testers; the theory is that only 4 developers (and all testers) will work on even-numbered releases, unless a piece of work comes up that really requires some specific expertise from one of the other devs. Each cycle will contain two days of dev work and two days of QA work (plus 1 day of scoping / triage / ...). My questions are: (a) Does anyone have experience with this length of release cycle? (b) Has anyone heard of this length of release cycle even being attempted? (c) If (a) or (b), how on Earth do you make it work? (Any pitfalls to avoid, etc., are also appreciated.) (d) How can we minimize the damage if this effort fails?

  Read the article

• How To Scale Canvas In Android

  - by Daniel Braithwaite

  I am writing a android game using Canvas as the way to draw everything, the problem is that when i run it on different android phones the canvas dosn't change size i tried using canvas.scale() but that didn't make a i difference. The code i use for drawing is ... public void draw( Canvas c, int score ) { Obstical2[] obstmp = Queue.toArray(this.o); Coin[] cointmp = QueueC.toArray(this.c); for( int i = 0; i < obstmp.length; i++ ) { obstmp[i].draw(c); } for( int i = 0; i < cointmp.length; i++ ) { cointmp[i].draw(c); } c.drawText(String.format("%d", score ), 20, 50, textPaint); if( isWon && isStarted ) c.drawText("YOU WON", 20, 400, resPaint); else if( isLost && isStarted ) c.drawText("YOU LOST", 20, 400, resPaint); } The function above calls the draw functions for the entity's on the screen, theses function are as follows Draw Function For Obstical : public void draw( Canvas c ) { Log.i("D", "COIN"); coin.draw(c); } Draw Function For Coin : public void draw( Canvas c ) { obstical.draw(c); } How could i make the canvas re-size to it would look the same on any screen ? Cheers Daniel

  Read the article

• Sharing swap space between Windows and Ubuntu

  - by Leftium

  This Linux Swap Space Mini-HOWTO describes how to share swap space between Windows and Linux. Do these instructions still apply to Ubuntu in 2011? How should I modify the steps for Ubuntu? Is there a better approach to sharing swap space? Based on the HOWTO, it seems best to create a dedicated NTFS swap partition: Dedicated so the swap file will be contiguous and remain unfragmented. NTFS so both Windows and Ubuntu can read/write to it. (Or is FAT32 better for this purpose?) Then, configure Ubuntu to prepare the swap space for use by Linux on start up; by Windows on shut down. I want to dual boot Ubuntu and Windows 7 on my X301 laptop. However, my laptop only has a 64 GB SDD, so I would like to conserve as much disk space as possible. update: There is an alternate method using a special driver for Windows that let you use a Linux swap partition for temporary storage like a RAM-disk, but it doesn't seem to be as good...

  Read the article

< Previous Page | 255 256 257 258 259 260 261 262 263 264 265 266  | Next Page >