Search Results

Search found 13214 results on 529 pages for 'git config'.

Page 259/529 | < Previous Page | 255 256 257 258 259 260 261 262 263 264 265 266  | Next Page >

  • Upstart script not working on Ubuntu

    - by Holy Crap
    I'm trying to write an upstart script to start orbited on startup. The script is as follows: #orbited start on startup stop on shutdown script exec /usr/local/bin/orbited --config=/etc/orbited.cfg end script When I run upstart orbited I get something like this: orbited start/running, process 605 But when I run status orbited right after doing that I get: orbited stop/waiting The script fails to start even though it says it's running. Any ideas? Thanks!

    Read the article

  • Virtual Hard Drive not booting - VMWare

    - by Chloraphil
    I have a .vmdk (VMWare hard disk) file that I cannot use as the lone disk in a new virtual machine. If I attach it to an existing virtual machine then it works fine. It has Windows Server 2003 on it. When I attempt to boot the new VM it attempts a network boot. EDIT: VMWare Workstation 6.5 I could not find a PXE option in the settings, and I did look in the VM config file for "PXE" but did not find one.

    Read the article

  • APPCMD syntax issue

    - by Adam
    I am trying to setup recycling logging events, using the following: appcmd set config /section:applicationPools /[name=' AppPoolName '].recycling.logEventOnRecycle:time But I am getting this error: Failed to process input: The parameter ''].recycling.logEventOnRecycle:time' mus t begin with a / or - (HRESULT=80070057). I used this technet article but I cannot figure out where I went wrong. Any ideas?

    Read the article

  • Skype status showing always online

    - by Geoff Dalgas
    Skype has recently started showing my online status as constantly "online" even after I have been inactive for longer than the configured time period of 5 minutes. Things that I have tried: Reinstalling Skype on all PCs Disabling all Skype Extras I use the same skype account on my desktop, laptop, and Iphone. Any ideas on why my skype status may be stuck or any other suggestions to help resolve this? UPDATE: I deleted config.xml from %APPDATA%/gdalgas in an attempt to resolve this which didn't help.

    Read the article

  • Put Conky behind the desktop icons

    - by Michal Gow
    Maybe I am trying do something impossible, but after hours of Googling I didn't get 100% answer yet. So - it is possible put Conky on Desktop backgroud (behind desktop icons)? The usual config: own_window yes own_window_type normal # (desktop, override) - I have the same result for all this attributes own_window_transparent yes own_window_hints undecorated,below,skip_taskbar,sticky,skip_pager Is giving me Conky with (pseudo)transparent background in front of icons (they are completely hidden behind it, even if in background of Conky is shown background image), while I am trying achieve opposite... My system: SuSE 11.4 KDE 4.4 (Release 3) x86_64

    Read the article

  • How do I change the search engine used by about:home?

    - by Lekensteyn
    Firefox 4's default home page provides a search engine with some snippets below. Is there any way to customize the search engine used through about:config or some other configuration file? localStorage["search-engine"] sometimes gets reset, possibly after a FF update. I would like to avoid creating a greasemonkey script that scripts on about:home. If an extension exist to fulfill the task, I'd be happy too. I'm using Firefox from Kubuntu 11.04 for that matters.

    Read the article

  • Changing Flash player of Firefox cache

    - by Prasenjit Chatterjee
    I want to relocate the Flash player plugin of Firefox cache so that it saves my C: drive space when I watch youtube videos. I successfully changed the firefox cache by opening about:config and then created a new string key "browser.cache.disk.parent_directory" where I put the value of the new cache location. But it doesn't work with online streaming contents such as youtube videos. Please guide me where does it get stored and how to change its cache into another drive.

    Read the article

  • hyperv machine guest loads slow

    - by Dani Avni
    this is by far one of the strangest things I have seen. I have a win 2008R2 cluster with a CSV. the CSV itself is on an iSCSI storage (hitachi HUS 110) basic config of the two hosts in the cluster is Dell R610 Win 2008 R2 with all patches 64GB 1 NIC for host access 2 NICs for guest access 2 NICs for iSCSI these machine work great and I can load a 2008R2 test guest machine on them in less than 90 seconds after the above config is running for over a year, I now need to add a new host. now the host is Dell R620 (Still intel but different CPU) Win 2008 R2 with all patches 64GB 1 NIC for host access 2 NICs for guest access 2 NICs for iSCSI I added this new host to the domain and to the cluster, I gave it access to the CSV and I tried loading the same guest machine that loads in 90 seconds in the other hosts. the machine loads in about 6 minutes. no matter how many times I try this the old hosts load the machine in about 90 seconds and this new host in around 6 minutes to eliminate any problems with the iSCSI connection, I added a new LUN and directly accessed it from the new host and I was working at around 300MB/s so no problem there. I also tested the connection between the other hosts and the new one and network is working fine there too. to eliminate problems in HyperV, I copied the machine to the local disk of the new host and it loaded in less than 20 seconds. now is the point were things get a lot stranger: in my tests I tried installing a fresh windows guest machine to the CSV from the new host. I noticed that while the fresh windows was installing, my test guest was loading in less than 90 seconds even on the new host (I repeated this a few times). If I paused the fresh install guest and tried loading the test guest again it loaded in 6 minutes. and again after I resumed the guest installation the test guest loaded fast. after the fresh windows was also loaded, I ran tests loading the fresh window and my test machine. each one of them loaded in about 5 minutes when I tried loading them separately. however when I started both of them in the same time they both loaded in around 2.5 minutes it seems that the iSCSI disk access is only working if it is under some load (although I never got to above 10% utilization according to the task manager) does anyone have any idea what could be the problem?

    Read the article

  • Why are unicode characters not rendering correctly

    - by sw1nn
    Background: I have some unicode characters in my prompt (git status markers essentially) I'm running urxvt under xfce on arch linux. I'm using DejaVu Sans Mono for Powerline font, specified via .Xresources line: URxvt*font: xft:DejaVu Sans Mono for Powerline:pixelsize=14 When I start urxvt the unicode characters do not render correctly. For example ? renders as â However, if I then start a new urxvt from inside the first terminal everything renders correctly. There doesn't appear to be any difference in the environment between the two terminals. What could be the difference between the first invocation and the nested invocation? I suspect the font is not correct in the 'outer' instance, but I'm unsure how to check the font of a running X window screenshot demonstrates the problem: Note: I moved this question from serverfault.com - i hope this site is more appropriate

    Read the article

  • I recompiled dozens of times, why is my OpenSSL Library and Header still not the same?

    - by Doug
    openssl OpenSSL support enabled OpenSSL Library Version OpenSSL 0.9.8o 01 Jun 2010 OpenSSL Header Version OpenSSL 1.0.1 14 Mar 2012 From PHP (5.4.4) info, this is the problem I have. I am dry out of ideas, and I cannot understand why it ins't working. This was my configure: ./configure '--with-apxs2=/etc/apache24/bin/apxs' '--with-mysql' '--prefix=/etc/apache24/php' '--with-config-file-path=/etc/apache24/php' '--enable-force-cgi-redirect' '--disable-cgi' '--with-zlib' '--with-gettext' '--with-curl' '--with-mcrypt' '--with-gd' '--with-pdo' '--with-pdo-mysql' '--with-mysql-sock=/var/run/mysqld/mysqld.sock' '--with-libdir=lib32' '--with-openssl=shared,/usr' '--with-mysqli'

    Read the article

  • Can't get my Raspberry Pi to keep a static IP

    - by JonnyIrving
    I recently got given a Raspberry Pi and I would like to be able to remote into it using puTTy from my laptop so I don't have to sit next to my tv with a keyboard and mouse to use it. I am able to get a puTTy session going when I know the IP address that my router has given the Pi on each session but it keeps changing on each reboot as I would expect. So I followed a number if instruction to go about configuring the RPi to keep a static IP address. This involved changing the file at '/etc/netwrok/interfaces' which now contains (password removed): auto lo iface lo inet loopback iface eth0 inet static address 192.168.1.82 netmask 255.255.255.0 gateway 192.168.1.254 auto wlan0 allow-hotplug wlan0 iface wlan0 inet dhcp wpa-ssid "BeBoxD304BF" wpa-psk "**********" Despite this however, each time I reboot my RPi it gives me a new dynamic IP address still. I also noticed that in the 'ifconfig' output below that the details of the eth0 doesn't contain IP details for inet addr, Bcast or Mask which have been present in all other examples I have seen online. eth0 Link encap:Ethernet HWaddr b8:27:eb:b5:95:da UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 00:87:c6:00:33:77 inet addr:192.168.1.83 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:918 errors:0 dropped:0 overruns:0 frame:0 TX packets:277 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 Also I'm not sure if this is relevant but it can't hurt! The file at '/etc/resolv.conf' contains: domain config search config nameserver 192.168.1.254 ..I heard it might mean something on one of the pages I was looking at. I would be very grateful for any help with this. I have tried everything I can think of and would really like to get this working this weekend so I can use it from work.

    Read the article

  • Win7 backup fails with "The system cannot find the file specified" 0x80070002 - has worked before

    - by Thorbjørn Ravn Andersen
    I have a 500 GB USB-disk which has been used as a backup device for a few years now, but now fails without telling me why. This is a Dell box with Intel USB-controllers (so the NVIDEA problem does not apply here). I have previously had problems with a Git package marking a non-existent directory for backup (adding it make the backup succeede). The inaccessible boot partition problem described in Windows Backup fails with 0x80070002: "The system cannot find the file specified" does not apply to me. I would appreciate hints on where to look to identify why my backup fails so I can fix it.

    Read the article

  • How can I change the default domain in an OTRS installation?

    - by Jamie
    I used a turnkeylinux.org otrs installation and I'm trying to configure the default domain of 'yourhost.example.com'. I tried the following: sed -ri 's/yourhost.example.com/mydomain.com/' /usr/share/otrs/Kernel/Config/Defaults.pm sudo shutdown -r now The next time I logged and tried to create a user, the default domain was still there. How can I change default doamin in an OTRS installation?

    Read the article

  • How to analyse logs after the site was hacked

    - by Vasiliy Toporov
    One of our web-projects was hacked. Malefactor changed some template files in project and 1 core file of the web-framework (it's one of the famous php-frameworks). We found all corrupted files by git and reverted them. So now I need to find the weak point. With high probability we can say, that it's not the ftp or ssh password abduction. The support specialist of hosting provider (after logs analysis) said that it was the security hole in our code. My questions: 1) What tools should I use, to review access and error logs of Apache? (Our server distro is Debian). 2) Can you write tips of suspicious lines detection in logs? Maybe tutorials or primers of some useful regexps or techniques? 3) How to separate "normal user behavior" from suspicious in logs. 4) Is there any way to preventing attacks in Apache? Thanks for your help.

    Read the article

  • Configuring sendmail to forward mail for a specific domain to a specific mail server without using M

    - by aHunter
    I am new to sendmail and would like to configure sendmail to forward all mail for a specific email address to another internal mail server. I need it to ignore the MX records and only send it to the server I specify but am not sure which files to edit or how to configure the sendmail config. Is it sufficient to add the server to the /etc/hosts and the /etc/mail/local-host-names files? Thanks in advance.

    Read the article

  • Free Markdown JS viewer

    - by maaartinus
    I'd like to use Markdown for documents to be exchanged with a colleague of mine. The ideal workflow would be IMHO editing the source in any plaintext editor while simultaneously viewing it in a browser. The client viewer should be able to redraw the text after each save automatically, and ideally even always switch to the most recent source file (so I don't need to navigate there manually). It'd be nice if I could (was allowed) modify the viewer a bit, things like using trailing spaces for line breaks are really terrible (I don't see them, my editor strips them, git complains about them, etc.). I'm interested in a software capable of this and easy to modify, and also in your opinions on the described workflow.

    Read the article

  • Possible to mount an ext4 partition image via FUSE?

    - by Catskul
    I'm attempting to mount an ext4 partition image in userspace. (no sudo, no special config/permissions modification to /dev/loop0 or /etc/fstab etc). So I'm hoping FUSE will come to the rescue. However it seems that each file system mounted through the FUSE system needs to have a special FUSE driver, and I've not been able to find a linux read-write ext4 FUSE driver for linux. Is there a way to mount ext4 images via FUSE (with write permission)?

    Read the article

  • Configure SQL server reportign service to send email

    - by Edoode
    Hi I'm configuring SQL server 2005 reporting server to send emails outside the domain. I have followed the steps outlined at MS but have a question: How can I supply a domain user to connect to the Exchange server in the same domain? I've tried <SMTPAccountName>DOMAIN\User</SMTPAccountName> in the rsreportserver.config.

    Read the article

  • How to setup NS for a subdomain

    - by DK M
    Hello, I have a DomainA.com use : ns1.mydomain.com ns2.mydomain.com I want create subdomain myname.domainA.com and use NS of other Server ns1.godaddy.com ns2.godaddy.com for that sub, please help, how to config in my NS ? I use Blind.

    Read the article

  • PHP-FPM conf location option when compiling php

    - by Danack
    I'm compiling PHP from source. I would like to set the location that PHP-FPM looks for it's config file. Apparently this option should be set via the configure option: --with-fpm-conf=/etc/php/php-fpm.conf According to http://php-fpm.org/wiki/Configuration_File However using this option on PHP5.5.0 gives the error configure: WARNING: unrecognized options: --with-fpm-conf How do I set where PHP-FPM should look for it's conf file when compiling from source?

    Read the article

  • Add usm user to a specified group in net-snmp

    - by tdi
    How to add usm created user to a group ? Is it even possible in net-snmp ? This is my initial config. I would like user tdi to be in group snmp3grp com2sec snmp3test localhost dummy group snmp3grp usm snmp3test view widok included system access snmp3grp "" usm priv exact widok all all createUser tdi MD5 "blablablabalab" DES rwuser tdi -V widok

    Read the article

< Previous Page | 255 256 257 258 259 260 261 262 263 264 265 266  | Next Page >