Search Results

Search found 11839 results on 474 pages for 'email forwarding'.

Page 261/474 | < Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268 | Next Page >

Enable Cisco ASA as an SSH Tunneling

- by Jim

I am trying to utilize my Cisco ASA as a SSH Tunnel. I've configured this before when using a Linux server as the SSH target, however I cannot seem to get it to work with the ASA. I have configured and enabled SSH on the Cisco ASA, as well as a username that I can SSH to the console, however the SSH Tunneling feature does not work. For example, on my PC I use Putty with a Local Tunnel defined to a server behind the ASA. I should be able to (if SSH connected to the ASA) be able to access the server. See screenshot of putty. has anyone come across this before? Again this is to use my Cisco ASA as a SSH tunnel, this is not a port forwarding. -Jim

Read the article
Juniper Networks SRX240 as a office router?

- by Jordan Mendelson

We're a small (7 person) fast growing startup who just got our new office and we're having a 100 Mbps line installed from Cogent. I'm not familiar with Juniper devices, however the equivalent Cisco appears to be rather expensive. Features we'd like: Offsite VPN access (PPTP or L2TP IPsec) - something Mac compatible IPv6 support NAT - ideally supporting multiple outside addresses mapped to VLANs DHCP DNS forwarding would be nice QoS to keep our SIP phones happy (managed through RingCentral) VLANs for guest/internal The device is going to be connected to a set of SIP phones as well as two Ruckus 7962s for wireless access. Eventually I'd like to connect it to a Juniper ESX switch as we grow. Would a Juniper SRX240 handle this ok?

Read the article
ICMP - TTL - Trace Route

- by dbasnett

I asked this question at Stack Overflow and then thought this may be the better place to ask. Given the following situation: PC --- |aa RTR1 bb| --- |aa RTR2 bb| --- |aa RTR3 bb| etc Each of the |aa rtr bb| is meant to be a router with two ports aa and bb. My question is this. When you do a trace route from PC which router port address should respond with time to live exceeded in transit message? I seem to remember being taught to think of the router as being in as many parts as ports, so that in my scenario when aa is forwarding the packet to bb and decrements the ttl to 0, it will be the address of the aa port in the failure message. I am trying to find the definitive answer. Thanks.

Read the article
Network wide rule to forwared IP address

- by Patrick

Hi, we have a virtual machine which hosts a web based bug tracker in our network which is reached internally via e.g. 192.168.1.5:9800. From the outside we made a port forwarding in our firewall so that the web site can be reached via e.g. 72.10.10.10:9800. Now that works fine but the problem is that we got different IP addresses to reach the same service depending if we are in the office or at home and when the service sends out an email the link doesn't always work :) So we are looking for a solution to fix it. One could be to make a rule in out firewall that all communication to 72.10.10.10:9800 is forwarded to 192.168.1.5:9800... If that's possible that is considering it's an IP address + a port. The reason we used a port is because we only got one static public IP address but multiple virtual web appliances. Thanks for any suggestions or solutions :) Patrick PS: The network is a Win 2008 R2 domain by the way

Read the article
Use Dynamic DNS to access Java servlet, still need port forward ?

- by Frank

If I use Dynamic DNS such as the free service at https://www.dyndns.com, do I still need to set up static IP and do port forward ? I have a DSL, most likely with dynamic IP address, and I run a Java servlet to get Paypal IPN messages on my notebook, in order for the messages to reach my notebook, I : [1] set up static IP and [2] did port forwarding. But I found each time the PC re-starts, it has a different external IP, so I was suggested to [3] get Dynamic DNS service like the free one mentioned above, but now I'm a bit confused, if I have step [3], do I still need to do [1] and [2], isn't step [3] supposed to do [1] and [2] for me ? But since I've already done [1],[2], now I wonder if they would cause trouble for step [3], do I need to undo them ? Or do I need all of them together ?

Read the article
Windows Load-Balancing, Forward-Proxying Software

- by LandonC

Does anyone know of any Windows software that will do forward-proxying load-balancing, like HAProxy does? There are tons of reverse-proxy solutions, but I can't find any that do what HAProxy does, that is, allows you to load-balance a group of forwarding-proxies. I have a proxy farm (don't ask) that I need to round-robin balance. HAProxy will do it, but is very unstable on Windows. Thoughts? I'd really appreciate it. And yes, this is an actual, production environment question.

Read the article
Socksify TCP connections reaching a gateway IP -- preferably without iptables

- by Alexandra Neagu

I have Virtualbox installed on Debian with a few virtual machines. I can't install anything in the guests, and I use host only networking, vboxnet0. The host IP in the host network is 192.168.56.1, and the guests have static IPs in 192.168.56.0/24. I access Internet with a SOCKS proxy (without authentication) and I would like the Virtualbox guests TCP connections to be sent through the SOCKS proxy. This would also be useful for socksifying external TCP reaching a gateway network card or wireless access point. I looked at transocks, tun2socks, with dante-client, etc., but I don't know how can I achieve this without enabling IP forwarding in the host and using iptables. Maybe to attach somehow the Virtualbox vboxnet0 network to the tunnel tun0 used by tun2socks? Or maybe there is a way to do NAT to tun0 in Virtualbox? I only need TCP traffic and I don't need UDP, not even for DNS.

Read the article
How to specify VNC port number with Mac OS X built-in VNC client?

- by Eonil

Is it possible to specify VNC port number in built-in VNC client of Mac OS X? I'm trying to connect to Xen VPS machine with Finder's built-in VNC client. I used address like this. vnc://server:port But it fails because it uses another port, and Finder's built-in VNC cannot handle port number. As I know it handles the number after colon as display-number, not a port number. Is there a way to specify port number on the VNC client? Or any workaround for this? (port forwarding??? I have no idea about it...)

Read the article
Godaddy hosting with dynamic ip?

- by Razor Storm

I bought a domain name on godaddy.com let's call it www.website.com, but my server has a dynamic ip, how do I resolve this issue? What I've tried: get a dns account at dyndns.com let's call it dns.dyndns.com, so I set up godaddy to forward the domain to dns.dyndns.com. problem: When the user goes to www.website.com, they see dns.dyndns.com in the url bar. Bad So then I set up the forwarding on godaddy to forward with domain masking, but then the problem is now that users can't even see url paths/get queries/ or hash marks anymore! `www.website.com/folder/search?id=4#ajax=4` becomes just www.website.com in the url bar. bad! What do I do?

Read the article
ssl between balancer members?

- by jemminger

I have apache running on one machine as a load balancer: <VirtualHost *:443> ServerName ssl.example.com DocumentRoot /home/example/public SSLEngine on SSLCertificateFile /etc/pki/tls/certs/example.crt SSLCertificateKeyFile /etc/pki/tls/private/example.key <Proxy balancer://myappcluster> BalancerMember http://app1.example.com:12345 route=app1 BalancerMember http://app2.example.com:12345 route=app2 </Proxy> ProxyPass / balancer://myappcluster/ stickysession=_myapp_session ProxyPassReverse / balancer://myappcluster/ </VirtualHost> Note that the balancer takes requests under SSL port 443, but then communicates to the balancer members on a non-ssl port. Is it possible to have the forwarding to the balancer members be under SSL too? If so, is this the best/recommended way? If so, do I have to have another SSL cert for each balancer member? Does the SSLProxyEngine directive have anything to do with this?

Read the article
Good way to run commands on remote computer without its own public-facing IP address (Linux Centos)

- by Chris Dutrow

Have a few computers running Linux Centos 6.4. They are connected to an unmanaged switch, which in turn, is connected to a router (Verzion Fios issue). What is a good way to "log in" to one of the computers so that I can run commands? Do I need to use SSH, or something different? Since the computers do not have their own public-facing IP addresses, do I need to set up some kind of port forwarding within the router? What is a simple, reliable way to accomplish this? Thanks so much!

Read the article
IPv6 static routes

- by user98651

I am looking to configure a few hosts with IPv6 on my network. The router (running CentOS 5) is configured with an Hurricane Electric (HE) tunnel which works fine on that host. However, I would like to statically add a few additional hosts on the same LAN to have IPv6 through this tunnel. No, I don't want radvd or dhcpv6 to do the work for me in this case. I already have IPv6 forwarding enabled in sysctl.conf. I am looking for help with the next steps (statically adding the routes). Lets say the IP addresses are as follows: Router: 2001:470:1b07:1:: Host1: 2001:470:1b07:2:: How would I go about making them see each other? Thanks in advance for the help.

Read the article
Strongswan and OpenVPN together

- by cmorgia

I have an host in Amazon EC2 which is configured with an OpenVPN Access Server. The only client to this server is acting as a gateway from a private network. I installed StrongSWAN 5 on the same host to allow windows 7 and iOS clients to connect using IPSEC. Both services works but what I cannot figure out is how to configure StrongSWAN to consider the OpenVPN tunnel endpoint as the only gateway available to clients. Basically I want all the traffic that comes from IPSEC clients to be entirely forwarded to the OpenVPN tunnel. The remote OpenVPN client that is exposing the private network has forwarding enabled and appropriate masquerading configured. The only missing point is to have the OpenVPN tunnel as the gateway for IPsEC clients

Read the article
How to use WeirdX applet instead of X11 for remote connections in Mac OS X?

- by penyuan

When I am away, I've got an Apple PowerBook set up to use X11 forwarding with SSH to connect to a remote iMac client in my room for server administration. Whenever I start X client programs on the client iMac, X11 would start on my PowerBook, which is OK, but... Question: Is it possible to change my settings so I can use the WeirdX (a web-based java X server) applet to take care of the X client programs instead of Mac OS X's default X11? Is there a config file I can edit to chance the $DISPLAY variable, and what should I set it to? Is this even the issue? Thank you very much.

Read the article
Missing eth0 configuration file

- by Godric Seer

I have two servers both running Scientific Linux 6 on the same network. Since I want SSH access to both of them, I want to give them both static IPs so I can setup port forwarding and not worry how my router assigns local IPs. I found that I need to edit the configuration file /etc/network-scripts/ifcng-eth0, however that file does not exist. The network card works fine, and I am able to ssh as long as I access the router and find the local ip. Can I simply make my own configuration file, or did I miss some step in configuring the system that I need to complete?

Read the article
Remote Desktop connection repeatedly aborting

- by DerKlaus

I connect to my workplace computer using Remote Desktop. After 1-2 minutes the application freezes to tell me after one more minute that the connection was aborted. It then reconnects. Everything works again for 1-2 minutes. Then the process repeats. Probably Forever. My coworkers do not experience such problems when connecting to the workplace. My workplace computer: Windows 7 32bit My home computer: Windows 7 64bit connected to the internet via WLAN-router with integrated ADSL modem (Linksys WAG200G) Things I already tried to fix the problem: disabled the Windows firewall disabled the other firewall reduced the MTU upgraded the firmware on the router configured port-forwarding to forward all packets to my home computer The problem remains unchanged. What could be the cause of the connection aborts? What else can I try to fix the connection? Thanks in advance.

Read the article
My IPSec VPN isn't allowing me to connect

- by jbondhus

I'm following this guide to create an IPsec VPN on a debian server. I followed all the steps, and it still isn't working. If I try connecting to it, I get an error. I've looked for the logs, but I'm not sure where they would be put, other than /var/logs. I aim to be able to browse the internet from my home connection, and access my home network as if it is my local network (eg. access my home fileserver and printers, and screen share my home computers remotely without a complicated port forwarding setup.

Read the article
DNS: domain2 points to domain1

- by Yar

I have one domain ("domain1") that is set up with hosting and mail (hosted by Gmail Apps). This domain works perfectly. I want a second domain ("domain2") to forward to domain1, but I don't want to use "DNS Forwarding." I would like to have it act EXACTLY like domain1, so that domain2/whatever points to the same resource as domain1/whatever WITHOUT AN HTTP REDIRECT NOR BROWSER TRICKS LIKE FRAMES. I would also love to be able to send mail to "blah@domain2" and have it go to "blah@domain1". Can this be set up, and how? I am using GoDaddy as registrar and DNS host for both domains. GoDaddy is also the web host for domain1, and mail hosting is with Google Apps.

Read the article
How do I configure OpenVPN for accessing the internet with one NIC?

- by Lekensteyn

I've been trying to get OpenVPN to work for three days. After reading many questions, the HOWTO, the FAQ and even parts of a guide to Linux networking, I cannot get my an Internet connection to the Internet. I'm trying to set up a OpenVPN server on a VPS, which will be used for: secure access to the Internet bypassing port restrictions (directadmin/2222 for example) an IPv6 connection (my client does only have IPv4 connectivity, while the VPS has both IPv4 and native IPv6 connectivity) (if possible) I can connect to my server and access the machine (HTTP), but Internet connectivity fails completely. I'm using ping 8.8.8.8 for testing whether my connection works or not. Using tcpdump and iptables -t nat -A POSTROUTING -j LOG, I can confirm that the packets reach my server. If I ping to 8.8.8.8 on the VPS, I get an echo-reply from 8.8.8.8 as expected. When pinging from the client, I do not get an echo-reply. The VPS has only one NIC: etho. It runs on Xen. Summary: I want to have a secure connection between my laptop and the Internet using OpenVPN. If that works, I want to have IPv6 connectivity as well. Network setup and software: Home laptop (eth0: 192.168.2.10) (tap0: 10.8.0.2) | | (running Kubuntu 10.10; OpenVPN 2.1.0-3ubuntu1) | wifi | router/gateway (gateway 192.168.2.1) | INTERNET | VPS (eth0:1.2.3.4) (gateway, tap0: 10.8.0.1) (running Debian 6; OpenVPN 2.1.3-2) wifi and my home router should not cause problems since all traffic goes encrypted over UDP port 1194. I've turned IP forwarding on: # echo 1 > /proc/sys/net/ipv4/ip_forward iptables has been configured to allow forwarding traffic as well: iptables -F FORWARD iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT iptables -A FORWARD -j DROP I've tried each of these rules separately without luck (flushing the chains before executing): iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j SNAT --to 1.2.3.4 iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE route -n before (server): 1.2.3.4 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 1.2.3.4 0.0.0.0 UG 0 0 0 eth0 route -n after (server): 1.2.3.4 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 0.0.0.0 1.2.3.4 0.0.0.0 UG 0 0 0 eth0 route -n before (client): 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 route -n after (client): 1.2.3.4 192.168.2.1 255.255.255.255 UGH 0 0 0 wlan0 10.8.0.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 0.0.0.0 10.8.0.1 128.0.0.0 UG 0 0 0 tap0 128.0.0.0 10.8.0.1 128.0.0.0 UG 0 0 0 tap0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 SERVER config proto udp dev tap ca ca.crt cert server.crt key server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" ifconfig-pool-persist ipp.txt keepalive 10 120 tls-auth ta.key 0 comp-lzo user nobody group nobody persist-key persist-tun log-append openvpn-log verb 3 mute 10 CLIENT config dev tap proto udp remote 1.2.3.4 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 mute 20 traceroute 8.8.8.8 works as expected (similar output without OpenVPN activated): 1 10.8.0.1 (10.8.0.1) 24.276 ms 26.891 ms 29.454 ms 2 gw03.sbp.directvps.nl (178.21.112.1) 31.161 ms 31.890 ms 34.458 ms 3 ge0-v0652.cr0.nik-ams.nl.as8312.net (195.210.57.105) 35.353 ms 36.874 ms 38.403 ms 4 ge0-v3900.cr0.nik-ams.nl.as8312.net (195.210.57.53) 41.311 ms 41.561 ms 43.006 ms 5 * * * 6 209.85.248.88 (209.85.248.88) 147.061 ms 36.931 ms 28.063 ms 7 216.239.49.36 (216.239.49.36) 31.109 ms 33.292 ms 216.239.49.28 (216.239.49.28) 64.723 ms 8 209.85.255.130 (209.85.255.130) 49.350 ms 209.85.255.126 (209.85.255.126) 49.619 ms 209.85.255.122 (209.85.255.122) 52.416 ms 9 google-public-dns-a.google.com (8.8.8.8) 41.266 ms 44.054 ms 44.730 ms If you have any suggestions, please comment or answer. Thanks in advance.

Read the article
Running command transparently over ssh

- by jnsg

By transparently I mean forwarding of: stdin, stdout and stderr standard signals (SIGHUP or SIGINT would be great for a start) As an example, consider these invocations of a (pointless) local and remote command: $ `cat - > /dev/null; sleep 10` < /local/file $ ssh user@host "cat - > /dev/null; sleep 10" < /local/file I can interrupt the first one with ^C just fine. But if I try this during the second one it only affects ssh, leaving the command running on the remote server if cat has already finished. I know about launching sshwith -t, but this way I can't send data via stdin. Is this possible with ssh alone at all?

Read the article
Blackberry Enterprise Server - Not running?

- by TheWellington

My BlackBerry enterprise server recently stopped forwarding messages to devices. In fact, the server claims that the last time it communicated with all the devices associated with it, was on Thursday night (4 nights ago.) The catch is this, the Exchange server is running properly (or as properly as Exchange can run :) ) The SQL server seems to be running properly. And the Blackberry Enterprise server seems to be running correctly. Other than the fact that the server has not communicated with any device since Thursday, and the fact that I am not getting messages, there appears to be nothing wrong. How do I get these message to be forwarded to devices again? I have restarted the BES services in the order suggested by the BlackBerry folks to no avail.

Read the article
Can I configure a DNS cache not to forward AAAA queries?

- by itsadok

I'm setting up an internal DNS cache because my firewall is having trouble handling all the sessions created by DNS requests. I tried using bind9, dnsmasq and DJB dnscache, they all help reduce the number of requests leaving my network, but there are still a lot of request being made. Looking at the log files, and tcpdump and dnstop outputs, it seems that requests that return SERVFAIL do not get cached at all. And a lot of those failed requests are AAAA requests, which is a shame, because I do not have ipv6 enabled on any server. I've looked at several ways to help the situation, and I think if I could somehow prevent AAAA record requests from being forwarded by the DNS cache, it would reduce the number of requests significantly. The closest thing I found was the filter-aaaa-on-v4 option in BIND9. However, this only removes the record from the server response, and does not prevent it from forwarding it. Any help would be appreciated.

Read the article
Linux router and firewall with IP accounting

- by Andrew

I'm working on a project to replace my organisation's aging Slackware gateway/router/firewall machine in our colo rack. Previously we used rc.firewall but we are now looking for something more modern and easily configurable. The requirements are: Act as a gateway router & firewall Port forwarding to a Terminal Server in the colo IP/traffic accounting, preferably accessible via SNMP (already using cacti for other servers) Possibility of acting as a PPTP server & routing these connections Is not an out-of-the-box Cisco product (don't have the finances or support to maintain it) I'd prefer to use Ubuntu or some other Debian-based distro but something that integrates everything we're looking for is certainly an option if it offers all the desired features and is easy to configure. Is there a simple set of packages that will provide me with the Firewall & Accounting features, or am I best served with a custom-built distro / other solution?

Read the article
Can I set up OpenVPN on two or more machines so that they can each act as client and server?

- by ianfuture

The question summarises what I want to achieve. In more detail: I have a Windows XP Pro PC at a work location that I want to be able to access my home Windows XP Pro PC and other home computers from. But I also want to be able to connect to the work PC from home. I think the term generally used is a "mesh" network. Can I do this with OpenVPN ? If so how would I do it? What are the most important things to remember to do? EDIT: The work Windows XP Pro PC is largely managed by IT Dept, I do have local admin rights to install things. Some settings are disabled. My main concern was firewalls and port forwarding on the work PC. Any suggestions?

Read the article
Are there any negative impact running all services on a single static IP?

- by Jake

I need to setup a VPN trunk (with remote branch office location), Video Conference and Web Server on-premise in the office. I am used to ISP providing blocks of 8 or 16 IPs. But I have a new ISP which says they only can provide a single IP. Are there any issues with running all services on a single IP? I don't think this has any thing to do with bandwidth..? I'm not using SSL certificates... I can do port forwarding to different machines... What else...? Disclaimer: I am a programmer by training. Sorry for noob question.

Read the article

< Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268 | Next Page >