Search Results

Search found 13634 results on 546 pages for 'great turtle'.

Page 261/546 | < Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >

• Problem with wake after suspend using USB remote.

  - by Bod

  Hi, I'm a linux newbie looking for some help. I'm currently setting up an XBMC HTPC using a laptop and 10.10 and all works great except for waking from resume using the power button on the remote. The suspend works from remote works fine as does the resume using the power button on the laptop. I've checked /proc/acpi/wakeup which initially showed the following. Device S-state Status Sysfs node C096 S5 *disabled pci:0000:00:1e.0 C0F1 S3 *disabled pci:0000:00:1d.0 C0F8 S3 *disabled pci:0000:00:1d.1 C0F9 S3 *disabled pci:0000:00:1d.2 C0FA S3 *disabled pci:0000:00:1d.3 C0FB S3 *disabled pci:0000:00:1d.7 C102 S5 *disabled pci:0000:00:1c.0 C22B S5 *disabled pci:0000:08:00.0 C115 S5 *disabled pci:0000:00:1c.2 C22C S5 *disabled C118 S5 *disabled pci:0000:00:1c.3 C22C S5 *disabled I've since configured the above so that the S3 devices above are enabled. I've confirmed that they are the correct devices using lspci 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) None of this has worked unfortunately and I'm now stuck. It simply refuses to wakeup from the remote. The USB receiver shows no activity LED while suspended. Suspend/resume from the remote works fine from Windows 7 so I know the laptop is ok with it. Any ideas? I need to get this sorted to gain Wife Approval for this system. Thanks, Bod.

  Read the article

• Being rocked...

  - by ZacHarlan

  After almost four and half years, I finally escaped from the world of telemarketing.     I'm now at a place that writes really good code, values testing, does routine code reviews, collaborates with each other so continuously and effectively somebody should make a documentary about it!   Today alone, I had two really smart and well respected developers go line by line through my code and show me how to make it better.  Seriously, people pay really good money for something like this and they don't get near the quality of feedback as I got!     +1 for me finally getting to a point in my career where i get to work with some of the best of the best in the software world!   I've been rocked by the fact that places like this actually exist.     I've been Rocked by the sheer size, complexity and simplicity of our website.     Most importantly I've been ROCKED by the fact that this many smart people check their egos at the door, gel together and look for ways to make software better than how they found it.  This is how to grow a business with tech... hire great people and watch them go!   Seriously, bravo.

  Read the article

• Estimate angle to launch missile, maths question

  - by Jonathan

  I've been working on this for an hour or two now and my maths really isn't my strong suit which is definitely not a good thing for a game programmer but that shouldn't stop me enjoying a hobby surely? After a few failed attempts I was hoping someone else out there could help so here's the situation. I'm trying to implement a bit of faked intelligence when the A.I fires it's missiles at a target in a 2D game world. By predicting the likely position the target will be in given it's current velocity and the time it will take the missile to reach it's target. I created an image to demonstrate my thinking: http://i.imgur.com/SFmU3.png which also contains the logic I use for accelerating the missile after launch. The ship that fires the missile can fire within a total of 40 degree angle, 20 either side of itself, but this could likely become variable. My current attempt was to break the space between the two lines into segments which match the targets width. Then calculate the time it would take the missile to get to that location using the formula. So for each iteration of this we total up the values and that tells us the distance travelled, ad it would then just need compared to distance to the segment. startVelocity * ((startVelocity * acceleration)^(currentframe-1) So for example. If we start at a velocity of 1f/frame with an acceleration of 0.1f the formula, at frame 4, would be 1 * (1.1^3) = 1.331 But I quickly realized I was getting lost when trying to put this into practice. Does this seem like a correct starting point or am I going completely the wrong way about it? Any pointers would help me greatly. Maths really isn't my strong suit so I get easily lost in these matters and don't even really know a good phrase to search for with this. So I guess in summary my question is more about the correct way to approach this problem and any additional code samples on top of that would be great but I'm not averse to working out the complete code from helpful pointers.

  Read the article

• Having a Proactive Patch Plan is the way to Go!

  - by user793553

  BUILDING A SUCCESSFUL PATCHING STRATEGY Make Patching Easy! Having a Patching Strategy for your E-Business Suite system is a great way to manage your system downtime, identify the proper resources needed to perform the necessary task and familiarizing yourself with the Patching Tools in EBS. Having a Proactive Patch Plan is the way to Go! Proactive Patching is a preventive measure allowing you to have a complete patching strategy when applying patches periodically. Oracle provides several tools to help you get started to set the foundation for a solid and proactive patching strategy in Note 313.1 - "Patching & Maintenance Advisor: E-Business Suite 11i and R12". It details all the steps and tooling available for the patching strategy along with the benefits. Among other things it covers the following: How to plan ahead for system downtime Patching Tools in E-Business Suite (Autopatch, OUI, OPatch) How to Identify Patches (RUPs, EBS Family Packs, Critical Patch Updates, etc) How to properly test your patching plan and move to Production Make sure you visit the New E-Business Patching Community! We encourage you to access the "E-Business Patching Community" prior to applying an E-Business Suite patch. Doing so will allow you to explore perspectives shared by industry peers, get real-world experiences with the patch, and benefit from known solutions and lessons learned. Additionally, Oracle Support engineers monitor discussion topics to help provide guidance and solutions for your E-Business Suite patching needs. This is a valuable opportunity to "Get Proactive" with the patching and maintenance of your E-Business Suite environment. Start now, and find fast, proactive resolutions before you begin. Related Articles: What's the Best Way to Patch an E-Business Suite Environment? Patch Wizard Utility

  Read the article

• Database Driven Web Application, C# Front-End and F# Back-End meaning

  - by user1473053

  Hi I am an intern working with ASP.NET. My current task is to make a website which will incorporate some jquery viewing features. This project seems to me will be primarily dealing with reading data from a database and making graphs out of them. This will require me to make custom queries from whatever the client is looking at. I think it is going to be what this guy calls an Ad Hoc Query tool My plan for this is to make it a database-driven website. So I can utilize the jquery dynamic viewing capabilities. I stumbled upon the functional programming paradigm and found F#. I read that because of it's functional programming paradigm, it makes it a good language to do asynchronous functions. I read about how you can use this with LINQ to SQL and how easy it is to make queries without actually putting the query language in. I understand the concept of the MVC design pattern. But I don't understand what they mean about C# being the front-end and F# being the back-end. Can someone clarify this to me? Also what are your thoughts about doing this project in this way? Any comments and thoughts are greatly appreciated. I feel as if learning F# will be a great learning experience for me. My guess is that the F# back-end is like the part where it controls the calls to the database. F# is possibly the model part of the design pattern. And C# is the controller. So HTML, Javascript and Jquery stuff will be my View design pattern. Clarify please?

  Read the article

• Designs for outputting to a spreadsheet

  - by Austin Moore

  I'm working on a project where we are tasked to gather and output various data to a spreadsheet. We are having tons of problems with the file that holds the code to write the spreadsheet. The cell that the data belongs to is hardcoded, so anytime you need to add anything to the middle of the spreadsheet, you have to increment the location for all the fields after that in the code. There are random blank rows, to add padding between sections, and subsections within the sections, so there's no real pattern that we can replicate. Essentially, anytime we have to add or change anything to the spreadsheet it requires a many long and tedious hours. The code is all in this one large file, hacked together overtime in Perl. I've come up with a few OO solutions, but I'm not too familiar with OO programming in Perl and all my attempts at it haven't been great, so I've shied away from it so far. I've suggested we handle this section of the program with a more OO friendly language, but we can't apparently. I've also suggested that we scrap the entire spreadsheet idea, and just move to a webpage, but we can't do that either. We've been working on this project for a few months, and every time we have to change that file, we all dread it. I'm thinking it's time to start some refactoring. However, I don't even know what could make this file easier to work with. The way the output is formatted makes it so that it has to be somewhat hardcoded. I'm wondering if anyone has insight on any design patterns or techniques they have used to tackle a similar problem. I'm open to any ideas. Perl specific answers are welcome, but I am also interested in language-agnostic solutions.

  Read the article

• How can I keep gnu screen from becoming unresponsive after losing my SSH connection?

  - by Mikey

  I use a VPN tunnel to connect to my work network and then SSH to connect to my work PC running cygwin. Once logged in I can attach to a screen session and everything works great. Now, after a while, I walk away from my computer and sooner or later, the VPN tunnel times out. The SSH connection on each end eventually times out and then I eventually come back to my computer to do some work. Theoretically, this should be a simple matter of just restarting the VPN, reconnecting via SSH, and then running "screen -r -d". However apparently when the sshd daemon times out on the cygwin PC, it leaves the screen session in some kind of hung state. I can reproduce a similar hung state by clicking the close box on a cygwin bash shell window while it's running a screen session. Is there any way to get the screen session to recover once this has happened, so that I don't lose anything?

  Read the article

• A software to lock regions of a screen to prevent any windows from overlapping

  - by cybervaldez

  I've just installed nexus dock (a similar application like rocketdock), after playing with the preferences i've come across a very curious option (under position & behavior) that says: Prevent maximized windows from overlapping the dock. With it enabled, any application I maximize(and i do mean any) won't overlap the dock, it's really great. So i'm thinking perhaps there's a software that does this kind of feature which is really ideal for keeping my workspace really organized. I really hate repositioning and resizing my windows everytime. Of course there's always the manual way of doing these but it's just too much of a bother when someone from the family uses the computer. Do you know any software that does this? even a software that can just save/remember window positions would also be nice too.

  Read the article

• What should I do when my team leader is unfair for no reason? [closed]

  - by crucified soul

  I'm a new software developer and this is my first job. It's a startup and the CEO and the working environment is just great. I work really hard and I believe that I also do my job well. But recently, I have felt like my team leader is being unfair to me for no reason. It appears that he is nice to my co-workers, but not me. I figure he is mad at me, but I didn't bother to find out why. I really love this company and I really love working there. But if my team leader continues to be unfair then I have no option other than leaving. How can I fix this? EDIT: The other day he called me into his office and wanted to see my work in the afternoon (Yes, in my country, at summer season after 5PM is afternoon. My office begins at 8AM. And I'm not saying I've problems to work after 5PM). At the time I was facing a weird runtime error and I was pretty tired. I explained the situation to him. Then he found a small logical error in my code and asked me why I didn't fix this. I told him I was trying to resolve this runtime error and that I was sure that this logical error had nothing to do with the runtime error. He then proceeded to yell at me. After fixing the logical error that runtime error was still there. This is not the only occasion he has been unfair to me. I'm saying is being unfair because he doesn't do this kind of thing to other developers when they do really silly mistakes.

  Read the article

• Watch Filesystem in Real Time on OS X and Ubuntu

  - by Adrian Schneider

  I'm looking for a CLI tool which will watch a directory and spit out the names of files that change in real time. some_watch_command /path/to/some/folder | xargs some_callback I'm aware of inotify (inotify-tools?) and it seems to be what I need, but I need something that is both Linux (in my case Ubuntu) and OSX compatible. It doesn't need to be lightning fast, but it does need to trigger upon changes (within a second is reasonable). Also, I don't necessarily need the exact CLI program mentioned above. If some underlying tech exists and is easily scriptable on both platforms that would be great too.

  Read the article

• Windows 7 cannot burn a DVD-R at 4x or 8x? (it seems to have to use the MAX speed)

  - by Jian Lin

  Windows 7 is great to have the ability to burn an .iso into a DVD-R, but it seems like there is no way to change the speed to 8x or 4x? (so it may go "max", which is 16x) because some of my DVD drives cannot read data all the time if the disc was burned at 16x, that's why usually i limit it to 8x. also, some articles say that disc burned at 4x can last a longer time, so i am tempted to burn something at 4x sometimes. any method or hack that can make it happen?

  Read the article

• DNS Zone file and virtual host question

  - by Jake

  Hi all, I'm trying to set up a virtual host for redmine.SITENAME.com. I've edited the httpd.conf file and now I'm trying to edit my DNS settings. However, I'm not sure exactly what to do. Here's an snippet of what's already in the named.conf file (the file was made by someone else who is unreachable): zone "SITENAME.com" { type master; file "SITENAME.com"; allow-transfer { ip.address.here.00; common-allow-transfer; }; }; I figure if I want to get redmine.SITENAME.com working, I need to copy that entry and just replace SITENAME.com with redmine.SITENAME.com but will that work? I was under the impression I needed a .db file but I don't see any reference to one in the current named.conf file. Any advice would be great and if you need more info to answer the question, don't hesitate to ask.

  Read the article

• ID Card printers and software

  - by Chris

  My company of about 60 people currently uses a Magicard Pronto ID Card printer and the Magicard ID card software. The printer is would be OK (not great) if they released 64 bit drivers for it, but Magicard ID is without a doubt one of the worst pieces of software I have ever used, ever. It would be OK for occasional hiring, but my company is looking to add a lot of people rather quickly. Does anybody know of decent ID-card printing software, and possibly a replacement printer? I might just "accidentally" run over this one with my truck a few times.

  Read the article

• What's Up for "We're Almost There" Wednesday

  - by Oracle OpenWorld Blog Team

   By Karen Shamban Wow - can't believe we're looking at Wednesday already!  Still so much to do, places to go, people to talk with. The last day for the Exhibition Halls is Wednesday, so be sure to spend time there if you haven't done so already. And don't forget (as if you would) that the famed Oracle Appreciation Event is Wednesday night on Treasure Island.  Here are just some of the big things happening Wednesday, October 3: Registration Moscone West, Moscone South, Hilton San Francisco, Westin St. Francis, Hotel Nikko, 7:00 a.m. - 6:30 p.m. Oracle OpenWorld Keynote featuring Oracle executives John Fowler, Edward Screven, and Juan Loiaza Moscone North Hall D, 8:00 a.m. - 9:45 a.m. Exhibition Halls Open Moscone South and Moscone West, 9:45 a.m. - 4:00 p.m. General Sessions Various times and locations Sessions, Demos, Labs Various times and locations Oracle Appreciation Event, featuring Pearl Jam, with Kings of Leon and X Treasure Island, 7:30 p.m. - 1:00 a.m. (note: must have approved wristband to attend) After what is sure to be a late night, it's good to know that the Thursday keynotes don't start until 9:00 a.m. They're going to be really great, so you won't want to miss them!

  Read the article

• Constituent Experience Counts In Public Sector

  - by Michael Seback

    Businesses and government organizations are operating in an era of the empowered customer where service  and communication channels are challenged every day.  Consumers in the private sector have high expectations from purchasing gifts online, reading reviews on social sites, and expecting the companies they do business with to know and reward them.   In the Public Sector, constituents also expect government organizations to provide consistent and timely service across agencies and touch points.  Examples include requesting critical city services, applying for social assistance or reviewing insurance plans for a health insurance exchange. If an individual does not receive the services they need at the right time and place, it can create a dire situation – involving housing, food or healthcare assistance. Government organizations need to deliver a fast, reliable and personalized experience to constituents. Look at a few recent statistics from a Government focused survey: How do you define good customer service? 70 % improved services, 48% shortest time to provide information, 44% shortest time to resolve complaints What are ways/opportunities to improve customer service? 69% increased collaboration across agencies and 41% increased customer service channels Are you using data collected to make informed decisionsto improve customer service efforts? 39% data collection is limited, not used to improve decision making Source: Re-Imagining Customer Service in Government, 2012 Click here to see the highlights.  Would you like to get started – read Eight Steps to great constituent experiences for government.

  Read the article

• How do I make a USB stick from which to install different OS's?

  - by Hanno Fietz

  Recently, I have made a number of USB sticks to install OS's (several Linux flavors, BSD, Windows) from, on machines that didn't have CD drives. Now, I would prefer to not overwrite the install USB sticks all the time, since it's handy to have them, but neither do I want to pile up USB sticks that I only need every 6 months. It would be great to have a bootable USB stick that fires up some minimal system, lets you choose an ISO image and then reboots from there. How would I go about this? Do I use some minimal Linux? Is there some kind of modified / specialized boot loader? Can I set up GRUB to do this? Should I use virtualization?

  Read the article

• "Unable to install GRUB in /dev/sda" when installing GRUB

  - by vicban3d

  I recently bought a shiny new Lenovo Yoga 2 Pro and I want to dual boot it with Ubuntu for studying purposes. Its built-in OS is Windows 8.1 and it has a 256GB SSD. I've made a separate 90GB partition just for Ubuntu and a live USB to install it. The first time everything seemed to work great, I solved the wifi issued by blacklisting ideapad_laptop, the installation went flawlessly and Ubuntu worked fine. When I got up the next morning and turned on my laptop it booted into Windows right away without ever showing the GRUB menu. So I tried to reset, and checked my partitions with the Disk Manager and everything looked fine. Since I couldn't find a solution online I went ahead and formatted the partition to try and install again. This time and every time since, the installation was aborted and I got a fatal error saying: Unable to install GRUB in /dev/sda Executing `grub-install /dev/sda` failed. This is a fatal error. Can anyone please suggest a solution to this problem? If any further information is needed I would be happy to provide it. Thanks. When installing I get the following in details: ubuntu kernel: [ 1946.372741] FAT-fs (sda2): error, fat_get_cluster: invalid cluster chain (i_pos 0). ubuntu grub-installer: error: Running 'grub-install --force failed.

  Read the article

• Where to install boot loader on a Zenbook Prime?

  - by Christians

  I cannot figure out where to install the boot loader on my Zenbook UX31A Prime. I have installed Ubuntu many times on normal hard drives, but this is the first SSD and I am struggling. Installed Ubuntu 12.04 64-bit selecting "UEFI: general" boot entry. Installation type: Something Else Created partition /sda5 mount as /, /sda6 mount as /home, /sda7 mount as swap Selected /dev/sda for boot loader installation. Other options are /dev/sda, /dev/sda1/dev/sda3 Windows 7 (loader) ... Grub comes up with 6 entries Ubuntu - this runs great Linux 3.2.0-29-generic recovery mode: mode hangs with "fb: conflicting fb hw usae interdrnfb vs EFI VGA - removing generic adapter" memtest86:erro: unknown command `linux 16' memtest86 serial: unknown command `linux 16' Windows 7 (loader) (on /dev/sda3): invalid EFI file path Windows Recovery Environment (on /dev/sda8): unknown command drivemap, invalid EFI file path. My workaround for booting Windows 7 is hitting ESC during boot, windows boot manager comes up and * for booting into Windows 7 I select "WIndows Boot Manager (PO: SanDisk ....". * for booting into Ubuntu I select ubuntu (P0: SanDisk...) How can I boot into Windows from Grub?

  Read the article

• Datacenter Backup Strategy

  - by EasyEcho

  What are common approaches to backup solutions in remote data centers? I am already familiar with general backup principals and have a very good backup strategy for our local data center but am having great difficulty extending it to a remote data center. We currently do a full backup on Friday, differential Mon - Thu, rotate offsite Friday morning ...rinse and repeat week after week. BTW, we use disks and have been very happy with this approach. We could buy a large storage server and backup everything to it, but this solution doesn't give you offsite. We could encrypt and upload to Amazon or some other online storage but that would take a large amount of time given the data and would be rather expensive paying for the bandwidth leaving the data center and receiving at amazon. We could drive to the data center every Friday and continue to rotate disks as we do now. But that just seems old fashion. What am I missing, are there better options?

  Read the article

• Better solution for boolean mixing?

  - by Ruben Nunez

  Sorry if this question has been asked in the past, but searching Google and here didn't yield relevant results, so here goes. I'm working on a fragment shader that implements both conditional/boolean diffuse and bump mapping (that is to say, you don't need a diffuse texture or a normals texture, and if they're not present, they're simply changed to default values). My current solution is to use a uniform float to say "mix amount". For example, computing the diffuse texel works as: // Compute diffuse amount scaled by vCol // If no texture is present (mDif = 0.0), then DiffuseTexel = vCol // kT[0] is the diffuse texture // vTex is the texture co-ordinates // mDif is the uniform float containing the mix amount (either 0.0 or 1.0) vec4 DiffuseTexel = vCol*mix(vec4(1.0), texture2D(kT[0], vTex), mDif); While that works great and all, I was wondering if there's a better way of doing this, as I will never have any use for in-between values for funky effects. I know that perhaps the best solution is to simply write separate shaders for mDif=0.0 and mDif=1.0, but I'd like a more elegant solution than splicing shaders before compiling or writing multiple shader files and keeping each one updated. Any ideas are greatly appreciated. =)

  Read the article

• WIth more mobile users, my geo ip database is becoming useless.

  - by Marius

  Hello there, I've been enjoying the benefits of Geo IP lookup from database for some time. Its great. People are increasingly trying to access my site from a mobile phones or 3G modems, and their physical location seems to have little relation to whereabouts my IP lookup tells me they are. A user who is on the east cost of my country, may be looked up as being in the far inland, or up north. And one user may be reported as being in one location in one moment, and seconds later, be 100s of kilometers away. This is becoming a problem, and I need to find a solution. I am already updating my database monthly, but it has little effect. What can be done? Thank you for your time. Kind regardsMarius

  Read the article

• Snow Leopard - Dock icons randomly disappear

  - by lostInTransit

  Snow Leopard works great! My mac's really fast after this. But sometimes the dock icons just disappear! I see the blue dot beneath when I click the empty space. So I know the item's there. But there are no icons! This happened for Safari and Downloads. Some people responded on the Apple forums that I should try and remove the dock's plist file. But this just restores the dock to its original settings! I don't want to lose my settings. Anyone else facing this issue with SL? Or is it a problem only I am facing? Thanks

  Read the article

• how to block select, move, copy, paste in vi?

  - by gojira

  I am trying to migrate from Notepad++ to vi. In N++, I constantly rely on block edit (or "column mode"), as it is a great increase in productivity: I can select a rectangular area of text by pressing ALT before marking with the mouse, and copy, move, paste the rectangular area anywhere. Also, it is possible to drag the cursor vertically so that I can type simulatenously on several subsequent lines at the same time. Is there any similar functionality for vi? If yes, how can I do that?

  Read the article

• How to code Time Stop or Bullet Time in a game?

  - by David Miler

  I am developing a single-player RPG platformer in XNA 4.0. I would like to add an ability that would make the time "stop" or slow down, and have only the player character move at the original speed(similar to the Time Stop spell from the Baldur's Gate series). I am not looking for an exact implementation, rather some general ideas and design-patterns. EDIT: Thanks all for the great input. I have come up with the following solution public void Update(GameTime gameTime) { GameTime newGameTime = new GameTime(gameTime.TotalGameTime, new TimeSpan(gameTime.ElapsedGameTime.Ticks / DESIRED_TIME_MODIFIER)); gameTime = newGameTime; or something along these lines. This way I can set a different time for the player component and different for the rest. It certainly is not universal enough to work for a game where warping time like this would be a central element, but I hope it should work for this case. I kinda dislike the fact that it litters the main Update loop, but it certainly is the easiest way to implement it. I guess that is essentialy the same as tesselode suggested, so I'm going to give him the green tick :)

  Read the article

• Finding a job: feedback on my current prodicument and my relentless efforts [closed]

  - by Michael

  I am a very well rounded IT guy, with a passion for programming in particular. I have been through a BS program less the internship as I refuse to go lower than minimum wage (i.e. free) and/or such opportunities find the institution lacking. Since then, the catalog for my degree has changed, so I am making peace without it. I go up for job interviews and get myself no farther than a submitted resume. I have even changed my strategy and made this website: http://goo.gl/qqpN8 to showcase my highlights (but not at all exhaustive) for specific areas in the US and paid for classified ads. The 'internship' is notable as I am just trying to get my foot in the door. Because IT is so vast, with programming and engineering in particular, I spend my time researching the requirements for the job I am applying for. This has made me that well rounded guy I spoke of earlier, but has made me a victim of being a jack-of-all-trades; unfortunately being a master of none. I embrace my gung-ho attitude and find it to be a trait that has powered my career before. But I am starting to lose steam. I want it straight. What is not appealing about everything I am doing? What are the technologies that I need to focus on that are in great demand at the moment?

  Read the article

< Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >