Search Results

Search found 13047 results on 522 pages for 'np hard'.

Page 263/522 | < Previous Page | 259 260 261 262 263 264 265 266 267 268 269 270  | Next Page >

• Fastest way to move files from a guest VM to the host?

  - by iTayb

  Hey there. I'm looking for the fastest way to copy files from a VM to physical servers. Setting up a network between them isn't a thing I'd like to do. I believe it is much more secure when not having one. VMware suggests using the Copy-VMGuestFile cmdlet from their PowerCLI interface, however I find it slow (Running at approximately 1.5MB/s). I thought of the following: Creating a new virtual hard drive, moving the files in, and download the .vmdk file from the server, then extracting it locally. It is possible, however will not work with working VMs, and I don't want to shut-down the VM every time I want to move files. Use the virtual floppy device and download the .flp file. It works even if the VM is running, but it is limited to 2.8MB. Do I have any other way? I'm using ESXi 4.1. Thanks.

  Read the article

• Running hardware with only 32bit drivers in 64bit windows

  - by Howard

  Recently we had to upgrade a system to handle added HD IP cameras. This upgrade involved an entirely new computer build with the exception of a rather pricey Geovision DVR (PCI/GV1480 series). Apparently while these cards do support Windows 7, they do not support Windows 7 x64. I'm stuck between a rock and a hard place here trying to figure out how we can remedy this, is there a virtualization solution that will allow devices with driver issues to passthru to the Guest OS? I was thinking XPMode may work for this solution however I am unsure if it runs 32bit or 64bit and if it'll allow driver-issue devices to pass to it. Any help would be greatly appreciated, Best Regards, Howard

  Read the article

• How to (hardware) RAID 10 on Ubuntu 10.04 LTS with 4 drives and motherboard with RAID contoller

  - by lollercoaster

  I have 4 500GB hard drives. I set up a RAID 10 in BIOS, much like shown here: http://www.supermicro.com/manuals/other/RAID_SATA_ESB2.pdf Then I followed these instructions: http://www.unrest.ca/Knowledge-Base/configuring-mdadm-raid10-for-ubuntu-910 Basically I cannot get it to work. I go through the instructions when I get to the "partition" section of the install, creating 4 RAID 1's (2 partitions on each drive, one for primary and one for swap space), then combining to make a RAID 10. Unfortunately it still shows 2 partitions, one 500 GB and another being 36GB for some reason. Any ideas? I think best would be if anyone had found good instructions (step by step) for how to do this...I've been googling for hours and haven't found anything...

  Read the article

• SQL Server 2008 R2 Enterprise database has unexpected 4GB database size limit

  - by Jesse

  I have SQL Server 2008 R2 Enterprise installed on a local Windows 7 x64 workstation. When I create a database on the server, it unexpectedly has a 4GB size limit (Database properties in SQL Server Management Studio say size = 3934.38 MB, space available = 47.13 MB). Unfortunately the database needs more than 4GB, and Enterprise is not supposed to have a practical maximum size. I confirmed the database is on the Enterprise server: SELECT @@VERSIONMicrosoft SQL Server 2008 R2 (RTM) - 10.50.1600.1 (X64) Apr 2 2010 15:48:46 Copyright (c) Microsoft Corporation Enterprise Edition (64-bit) on Windows NT 6.1 <X64> (Build 7600: ) The database file is not set to restrict growth in SQL Server Management Studio, and there is plenty of hard drive space. The database was copied from SQL Express (which has a 4GB limit), but the same occurs with a fresh database creation. I've spent a couple of hours trying to figure this out and Google-searching, to no avail. Any ideas?

  Read the article

• How to make Windows 7 use a different name for the Program Files folder?

  - by Renato Silva

  How can I properly rename the Program Files folder in Windows 7? That is, not simply rename the directory and create symlinks, but make Windows itself see the location of installed programs as something else. I have already renamed the directory to Programs (using desktop.ini for a localized name in explorer), and made Program Files into a symlink to that, but I wonder if it's ever possible to erase the symlink by configuring Windows to, under all circumstances, assume Programs as the actual name for the programs directory. I heard that it should be possible to choose the name from Windows installation, but I'm not sure. Besides, I don't want to reinstall Windows from scratch. Before you mention %ProgramFiles%, no, it doesn't work. I'm not sure if Windows has that location hard-coded, or if replacing all occurrences in the registry would be enough.

  Read the article

• Recovering OS X Mail Accounts Lost in Crash

  - by Tim

  I had a hard crash on my Mac PowerBook and when I restarted, Mail came up with only my MobileMe account still available and I cannot figure out how to restore the other eight email accounts I have. The directories in ~/Library/Mail all seem to be there. I even did an rsync of the modified .plist files from a TimeMachine backup of the directory from before the crash (unfortunately, I was on travel, so the backup is more than a week old and I'd like to try and recover from that point without having to entirely restore from TimeMachine). I also did a fix permissions. So my questions are where exactly is the account information for Mac Mail kept? Any thoughts of what might have caused the failure? Why does only MobileMe come up? Any other thoughts on how to fix things?

  Read the article

• Ubuntu Remix on Acer Aspire One Netbook keeps freezing

  - by user7553

  It came with a Windows XP installation and I just couldn't deal with the screen constantly blacking out. Later on I found out they designed a specific key on this netbook for it. Anyways I installed Ubuntu Remix and it fixed it. However a lot of bad things are happening now. 1) If I want a long video or lots of music it will lockup after an hour. 2) Plugging it to an external monitor for more then 1 hour will black out. 3) Constantly running fsck after a lockup and then I lose nodes / fragments and what not :( I am really not sure what to do, both blacking out and lockups really mess my hard drive up. I have to manually run fsck every time it happens. My gf has the same kind of netboot w/ Remix (not the same model number) and it runs perfectly fine on hers. Except for skype eating up all her CPU.

  Read the article

• Mysqldump causes "Too many connections"

  - by vbachev

  A scheduled backup using mysqldump on one of our databases is causing Too many connections. The database is of both InnoDB and MyISAM tables with size of around 500Mb. The Too many connections appears for about 2-3 minutes We understand that mysqldump locks the tables and causes all other queries and connections to pile up and jam the mysql server. We need frequent backups and we cannot afford server downtime or putting websites in maintenance mode while doing it. Our websites are global and traffic is high all the time so its hard to find a moment for backups. How can we avoid downtime during backups?Is there maybe a way to use mysqldump in way that it will not lock all tables at the same time?Is there an alternative to backing up with mysqldump?

  Read the article

• Windows 7 Recovery Console File Access Denied

  - by Ty Rozak

  Recently by computer crashed and was stuck in a boot loop. So I created a Windows Recovery CD and booted from that. When I use the command prompt in the recovery console, I cannot see any of my personal files or folders (such a my Users folder with My Documents). Is there a way to access these files? The only reason I would need to fix the computer properly would be to get these files off of the computer and onto a hard drive. Any other fix suggestions would be greatly appreciated. I have tried both system repair and system restore from the Recovery Console, but neither seem to work. Thanks.

  Read the article

• How to enable extended logging for classic asp on IIS7 on Windows 2008 R2

  - by Neil Trodden

  I had to deploy an application that was not written by me onto the above configuration. It is a rather bizarre hybrid of asp.net and classic asp and it's the classic asp that is proving troublesome. The client is having problems with 500 Internal Server Errors appearing and I can see some of these in the logs but I only get the error code and the page name but little else. What I would like to see is the actual error message to at least give me an idea what is going on (or not going on, depending on your point of view) I don't want to display errors in the browser as I don't know the code well enough and this could (for all I know) display some crazy code where the db password is hard-coded into the site.

  Read the article

• PDF problems with Evince on Ubuntu

  - by ILMV

  One of my collegues is trying to print a PDF that our designer has sent him, created using Adobe InDesign CS4 (6.0.4). When he opens it up using Evince (version 2.28 on Ubuntu 9.10 thin client) it displays exactly how we expect it to, however when he prints it's not rendering correctly, for example: Missing one logo, the other dozen display perfectly Missing a white box with 30% opacity (without this the blue text sits on a light blue background) The dotted border of a box is screwed up (missing dots in the corners, but fine on the straights) Finally the font quality is slightly poorer than a print out we've done on a working machine. I have tried it on my Ubuntu dev box (Evince version 2.22 on Ubuntu 8.04 server) and it displays and prints perfectly. Can anyone offer an explanation as to why this might be happening, I find it hard to understand how an older version of Evince is displaying it better than a newer version. Thanks! EDIT Just for anyone surfing in, it's likely yo be a CUPS problem on our server, cheers ;-)

  Read the article

• Boot drive is incorrect one.

  - by Dwayne

  I have several hard drives installed. I normally use c: as my boot drive and a much larger drive (h:) for storing most of my files. I found a subfolder in my c:windows folder named windows after a failed reinstall of Vista. Upon inspection I determined it to be older than the c:windows folder and therefore it must be the older, working version of the boot. I renamed the c:windows folder to c:windows.bad and moved the sub windows to the c: root directory. I also copied it to the h: drive. Now MSCONFIG reports that the copy that is booting is the h: copy. How can I change it back to the c: copy and can I delete the c:windows.bad file set?

  Read the article

• What are some hosted MySQL solutions?

  - by bigmac

  I would like to host a MySQL database somewhere. The basic solution would be to get a VPS, but then I am stuck doing all the sysadmin stuff. It's not terribly difficult if you are not doing anything fancy, but if something goes wrong (like a security breach), it may be hard to resolve or even diagnose in the first place. On the other end of the spectrum, I found Xeround and Amazon RDS. Xeround is not exactly standard MySQL. Amazon seems a bit complex to get started (which is weird because they specifically say it is "simple to deploy"). Why is there nothing in the middle? Is there no demand for a basic hosted MySQL solution?

  Read the article

• How can I capture a one-time full backup of a server using AMANDA?

  - by Daemon

  Suppose I have a preconfigured AMANDA server running automated network backups of directories specified in my disklists file. Normally, AMANDA will backup targets disks to /dumps/amanda. Is there any single command or method to perform a manual, one-time, full backup dump to another destination drive? I ask since I'm investigating the possibility of introducing rotating external hard-drive backups for offsite storage and I want to leverage our existing backup strategies wherever possible. Ideally, a full backup restore should be achievable from only any one of these offsite backup discs.

  Read the article

• How can ShadowProtect SBS backup to alternating external drives?

  - by detly

  I am trying to configure ShadowProtect SBS (v. 4.1.5.10129) in Windows Server 2003 SBS to backup my server hard drives to two alternating external drives. What I want is to be able to swap one drive for another every Friday, and have ShadowProtect continue on the same schedule. Ideally, this would require absolutely no user interaction whatsoever, apart from physically unplugging one drive and reconnecting the other. The trouble is, Windows Server 2003 does not allow you to assign the same drive letter to two different devices. So if I plug in drive #1 and assign it drive letter "X:", the next week when I unplug it and plug in drive #2, it gets some other letter. But since ShadowProtect is set to backup to "X:\", it can't find it and the backup fails. The drives are Samsung STORY Station 3.0 2TB drives. How can I configure things so I can just swap the drives over every week and not worry about having to reconfigure drive letters every time?

  Read the article

• "the user profile service failed the logon"

  - by crazybmanp

  "the user profile service failed the logon" i had gotten this error when trying to login last night. i looked it up online and found that this was caused by an error (that is still unfound, apparently) that is causing windows to mark profiles as backup, and that the best way to fix this error is to do a system restore from the repair your computer special boot option. what i would like to know is if there someone happens to know the cause of this error, as i would not like it to happen again. Computer specifications OS: Windows 7 hard-disk check completely clean "repair startup" scan and fix: clean, no problems virus scans with kaspersky: clean (while not the usual information for specifications, i felt this info was more important for this case, any other information can be asked for.

  Read the article

• Custom Icon for NFS Volume Mount - Possible for OSX?

  - by James

  We are naming our various network volumes after Planets! I renamed the Mercury.icns icon, to .VolumeIcon.icns and copied it over to the mount point folder of the NFS server. So far remounting the NFS share does not seem to employ this icon. Looking on the NFS server, there appears to be two VolumeIcon files. Can someone tell me what I am doing wrong? Permissions? Do I need a .DS_Store file there as well?? It shouldn't be this hard! EDIT: Should have mentioned, the NFS server is Ubuntu 12.04.1. NOT an OSX server.

  Read the article

• Youtube videos all appear transparent in Chrome (I can see through to my desktop -- see pic!)

  - by kalaracey

  MBP 6,2 :: Google Chrome 13.0.782.32 beta :: Adobe Flash Player 10,3,181,26 UPDATE: only Youtube is affected. Vimeo, other flash, etc. all works great. Hello. I recently had to hard reboot my MBP. After that, I could not watch Youtube videos or (I believe) other flash enabled content. The videos appear transparent, as if there were a "hole" in my browser (Chrome) such that I could see through the hole and see my desktop. I've attached a picture (just picked a random video) Thanks.

  Read the article

• Several "SideBySide" errors in the event viewer (Windows XP SP3)

  - by Wesley

  Hi all, For some reason, my netbook continuously comes up with SideBySide errors in the event viewer under Computer Management. Is there some way to get rid of these errors? My netbook occasionally BSODs and looking back into the event viewer after, at least 8 SideBySide errors were logged prior to BSOD. Please help! Thanks in advance. Netbook is a Samsung N120 with upgraded RAM to 2 GB. EDIT: So, SideBySide errors have been resolved and apparently the BSOD isn't related. But I remember specifically, that last time I had a BSOD, it was due to an "unknown hard error." What causes that?

  Read the article

• Performance problem with Win Server 2008 at vbox on Ubuntu 9.10 Server

  - by Diskilla

  Hey, i´ve got an Ubuntu 9.10 Server and tried to install Windows Server 2008 in a virtual machine. The Problem is, the Server has got 8 cores, but the virtual machine seems to have problems with that. The VM is very slow and not really usable if i set the VM-config to more than one core. Is it set to only one core everything works fine, but thats not a solution because I bought the Server with several cores for a reason... Does anybody know this problem or has got a solution? I feel like I read the entire internet via Google... no solution found. Greetz Diskilla P.S.: I´m from Germany and it´s kind of hard to ask in english :-) I hope I din´t make that much mistakes.

  Read the article

• Disk Redundancy across different server

  - by Mascarpone

  I have 3 servers, all with the same specs: Intel CPU 8 GB RAM Linux or BSD Single 2TB desktop SATA with more than 10K Hours of operation, with only less than 300 GB Used My provider cannot install a second hard drive, but can guarantee me that the drive will be replaced immediately in case of failure, with another equally crappy drive. The likelihood of drive failure is high, and since I can't use RAID, I was thinking about keeping a back up of each machine on all the other machines, so that there are always 2 copies on 2 different drives, plus the original. I would synchronize the drives every hour, with rsync, to guarantee some sort of redundancy, since bandwidth inside the DC is free, so it would be much cheaper than offsite backup. (A daily offiste backup is kept anyhow). What do you think? Any suggestion?

  Read the article

• Recovering drivers from previous installation?

  - by Walkerneo

  Yesterday I bought a new computer and I've been setting it up since this morning. The hard drive came with windows 7 home premium (x64) installed, but I decided to instead install windows 7 ultimate (x64) - this is what I'm currently using. Unfortunately, there were some drivers that were installed that I need in this installation. I only notice because the computer doesn't have the ethernet drivers, so I'm only able to connect to the internet via wireless. There are other drivers missing as well, but I'm not yet seeing the effects. I still have the Windows.old folder with the previous installation, which has the drivers. Is there any way to copy the necessary ones over? I tried the options for updating driver software through device manager with the path set to System32\drivers of the old installation, but it didn't find anything.

  Read the article

• Pysdm has disabled my ability to write to my storage partition

  - by Atlas

  I have a dual boot setup with Windows 7 and Mint 13 Cinnamon. As well as their respective partitions I also have a large one (NTFS) for storing all my music, videos, documents etc. I downloaded pysdm as I was told it would enable me to configure Linux to auto-mount my storage partition. It has indeed been helpful in auto-mounting my storage. However, since installing it I can no longer write to the partition which makes 500GB of my hard drive utterly useless! I've tried to unselect the "Mount file system in read only mode" option, but the program keeps re-checking it after I close that window (and even when I click apply). Why is it doing this and how can I get it to recognise that I need to read AND write on that partition?

  Read the article

• Server only powers (but doesn't POST) when IDE drive is powered

  - by Jookia

  So after a thunderstorm last night which did a little damage, a Gigabyte server has decided it's going on power on but not POST. If it is POSTing, it's doing a very bad job at telling me. No beeps, nothing. Power seems to reach the components though. CD Drive opens and closes. So after stripping it back, I've found that the difference between this behaviour and deciding it's not going to power on for more than half a second, is having a power cable plugged in to one of the IDE hard drives. Is this normal, or a sign that the PSU has had it?

  Read the article

• Overriding Debian default groups from LDAP

  - by Ex-Parrot

  This is a thing that has always bothered me: how am I best to handle Debian standard groups for LDAP users? Debian has a number of groups defined by default, e.g. plugdev, audio, cdrom and so on. These control access in standard Debian installs. When I want a user from LDAP to be a member of the `audio' group on all machines they log in to, I've tried a few different things: Adding them to the local group on the machine (this works but is hard to maintain) Creating a group in LDAP with the same name and a different GID then adding the user to that group (breaks reverse / forward GID mapping, doesn't seem to work) Creating a group in LDAP with the same name and same GID and adding the user to that group (doesn't seem to work at all, things don't see the LDAP group members) Creating a group in LDAP with the same name and same GID then removing the local group (this works but upsets Debian's maintenance scripts during upgrades that check for local system sanity) What's the best practice for this scenario?

  Read the article

< Previous Page | 259 260 261 262 263 264 265 266 267 268 269 270  | Next Page >