Search Results

Search found 21141 results on 846 pages for 'old mac'.

Page 277/846 | < Previous Page | 273 274 275 276 277 278 279 280 281 282 283 284  | Next Page >

• Bridge virtual machines out WLAN interface

  - by Thomas

  It seems that my wlan card (intel 5100 AGN) firmware doesn't allow "spoofing" MAC addresses. This has the side effect of destroying the capability to bridge out my virtual machines on that interface. Apparently this is a common thing on wlan cards. I can see the incoming traffic just fine in my virtual machines, but their DHCP queries don't get bridged out of the WLAN card. It works perfectly well when using the wired ethernet port. Is there a workaround for this? MAC-NAT or something? I don't want to route my virtual machines out to the Internet because I don't want my host OS to even have an IP address. I'm using Linux and KVM for virtualization.

  Read the article

• Creating an interactive "movie" from a Microsoft PowerPoint 2003 presentation (.ppt file) containing animation

  - by Andrew

  I have created a Microsoft PowerPoint 2003 presentation (a .ppt file) on Windows XP that contains a lot of animation, using PowerPoint's Custom Animation tools. I would like to share this presentation -- animations and all -- with a colleague who has a Mac computer and does not have PowerPoint or Keynote. Is it possible to make a "movie" from my .ppt file that contains a lot of animation? I recall that another colleague once made me a QuickTime "movie" from a PowerPoint file, I think (although I do not remember whether he made it using Windows or Mac). On this "movie," clicking advanced the animation/slide, just as clicking would do in an actual PowerPoint presentation. In that sense, it was not really strictly a movie, since I could interact with it by clicking. Do you know how to make such an interactive "movie" from a PowerPoint 2003 presentation (a .ppt file)? Thank you for your time!

  Read the article

• VMWare ESXi virtual machine can contact the gateway but not the DNS server

  - by Nathan Palmer

  I am having a bit of a strange issue. I have a VMWare ESXi server with two virtual machines running on it. They are running just fine and can communicate on the network without a problem. I am now trying to add a third. I am installing Ubuntu 8.04 Server. I assign it a static IP address and it's a fresh installation. Once installed I can ping the gateway but I cannot ping the DNS server. It's on the same network with the other two VMs which are communicating just fine. I have tried to reinstall the operating system but it still fails to connect. Here is /etc/network/interfaces auto eth0 iface eth0 inet static address 192.168.1.23 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.1 dns-nameservers 208.67.222.222 #opendns dns-search mydomain.com Here is route Destination | Gateway | Genmask | Flags | Metric | Ref | Use | Iface localnet | * | 255.255.255.0 | U | 0 | 0 | 0 | eth0 default | 192.168.1.1 | 0.0.0.0 | UG | 100 | 0 | 0 | eth0 Since I'm running this behind a FortiGate this is what the sniff command gives me when I try to ping 208.67.222.222 arp who-has 192.168.1.1 tell 192.168.1.23 arp reply 192.168.1.1 is-at MAC 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request As you can see it looks like I never get a response. One interesting thing I notice is the arp reply's MAC doesn't look right. I have cleared the FortiGate's ARP cache though and checked the entry and it seems correct. The MAC it lists is the one for the router. However if I ping from a different virtual machine that is also Ubuntu 8.04 with a nearly identical configuration I get this. 192.168.1.22 -> 208.67.222.222: icmp: echo request 208.67.222.222 -> 192.168.1.22: icmp: echo reply 192.168.1.22 -> 208.67.222.222: icmp: echo request 208.67.222.222 -> 192.168.1.22: icmp: echo reply 192.168.1.22 -> 208.67.222.222: icmp: echo request 208.67.222.222 -> 192.168.1.22: icmp: echo reply So, what could I be missing? Thanks.

  Read the article

• How to prepare and secure a Macbook Pro for work/office?

  - by sunpech

  I plan to use my Macbook Pro at work/office. Before I do so, I will need to speak to my manager on how to properly prepare and secure it since this is the first Mac that will be regularly used on the network in the office and company intranet. The intranet comprises mostly of PCs running Microsoft Windows XP, Server 2003, and Windows 7. So there's definitely a Microsoft-only culture in the office, and the infrastructure/networking team are mostly unfamiliar with non-Microsoft technology and software. What steps and software would I need to prepare and secure my Macbook Pro for work/office? Antivirus/Spyware software for Mac required/necessary? What options do I have to encrypt files, or possibly the whole drive/partition? What network/firewall settings should be enabled?

  Read the article

• Problems switching to QEMU control panel with -nographics

  - by tor

  It seems that the terminal does not recognise CTRL+ALT+2 when typed, so I don't know how to quit the QEMU emulation, or switch to the QEMU control panel. I am running Mac OSX Lion, and I type $ qemu-system-arm -M verdex -pflash flash.img -nographic -sd sdcard.img to start QEMU emulation of an ARM system in the Terminal. I learned from this site that typing CTRL+ALT+2 should work, but the only thing that happens to me, is that a "2" is printed on the command line of the virtual operating system. Any ideas on what could be wrong? Is this a Mac specific issue? (The same problem occurs in both terminal.app and iTerm2)

  Read the article

• Epson XP-600 will not print properly with all new ink recently installed

  - by Joy

  I just installed brand new Epson 273 ink cartridges ($64 worth!) in my Epson XP-600 printer. One box had all the colors plus black, and one had the fatter black cartridge. I am not getting ANY black print on paper, although, when I lift the cartridges out, they show ink inside. Now the yellow is saying LOW though all cartridges are less than 2 weeks old. I only use this printer sparingly—not for business or work reasons. I am ready to scream, as the ink cost almost as much as the actual printer (which is barely 7 months old)! Any ideas on how to solve this issue?

  Read the article

• rhel/centos vs. ubuntu (possibly other debian-based systems) linux in handling duplicate ips in the same subnet

  - by johnshen64

  This has bothered me for quite a while but I never found out why or how to change the behavior. ip duplicates could be caused by typos or dhcp errors etc., but they do occur from time to time. in rpm-based systems such as centos, the old server with the duplicate ip wins, and the new server will get an error in bringing up the nic (ip address already used). this is somewhat harmless because we can just fix the system that is coming up. ubuntu only the other hand happily grabs the used ip for itself and leave the old server/device without a valid ip. this is the more dangerous behavior because it causes outages. what i want is to change the ubuntu behavior to that of the centos/rhel so would appreciate any help.

  Read the article

• Tweaks on nvidia-settings only working when the program is opened

  - by Igoru

  I have two monitors. The master one (17") is 1yo, and the secondary (15") is really old, like 4yo. This old screen is having problems displaying colors... They are a little bit darker, what is a problem when I'm viewing pics. I have a GeForce 9800, so I changed some settings inside nvidia-settings, that fit better with this second screen. But those settings just are applied when I first open nvidia-settings. First time I configured this, it worked. I turned off computer, next day turned it on, and screen is dark again. As soon as I open nvidia-settings again, the screens get lighter again! How can I make those settings permanent and loaded at startup?

  Read the article

• How do I configure custom routes when an interface is configured?

  - by ManicDee

  Other Superuser questions have addressed the issue of adding custom routes to access e.g.: multiple networks of a corporate network through one interface, while accessing the Internet through another interface. So assuming that I have a script to add specific routes when en0 is configured, and a separate script to add specific routes when en1 is configured, is there some way I can trigger those scripts to run automatically when Mac OS X/Darwin starts and configures those interfaces? Back in my Linux days, it was possible to add an option in /etc/network/interfaces along the lines of: iface eth0 inet dhcp up /usr/local/sbin/eth0-routes-up Is there something similar for Mac OS X?

  Read the article

• Migrate AD DS Server 2003 to Server 2008 R2

  - by user2566483

  I would like to get a couple opinions Found this article online and wanted to know if it is good to follow http://www.msserverpro.com/migrating-active-directory-domain-controller-from-windows-server-2003-sp2-to-windows-server-2008-r2/ Couple of things that need to be done. 1. Move over all active directory settings from old Server 2003 server to new Server 2008R2 2. Setup all users on new server using csvde. csvde -f output.csv -- on old server csvde -i -f output.csv -- on new server Any advice would be greatly appreciated.

  Read the article

• Upgrading my Active Directory domain from Server 2003 to Server 2008 R2

  - by drpcken

  We are currently a single domain on a single network running Server 2003 Standard and Exchange 2007. I have a new server up and running (added to the domain already) with Server 2008 R2 on it. I want this to become my Primary Domain Controller, thus replacing my old Server 2003 server. I know I should just be able to run dcpromo on the new server, then decomission my old server, and raise my domain functional level to match the 2008 server. My only concern is the Exchange 2007 server. Is there anything I need to know relevant to it before I start? Thanks!

  Read the article

• How can I tell if ZFS (zfs-fuse) dedup/compression is applied to a particular file?

  - by asari

  I have a zfs formatted partition using zfs-fuse for linux (Ubuntu). I had used it for a while, and then enabled dedup and compression on it (zfs set compression=on/dedup=on). Now I think I have some files that are dedup'ed and compressed, and file that are not yet. It was OK, but sometimes I was confused. Let's see, following command would consume almost 4GB of my zfs storage: cp oldfile.4GB newfile.4GB .. and this would consume almost zero: cp newfile.4GB newfile.4GB.2 This is because the old file is not yet compressed, so dedup not happened, I think. My idea is -- if I can find old files that are not yet dedup/compressed, I can perform batch copy/rename/remove them to eliminate duplicity and redundancy. But how I can check that? I know I can re-copy whole contents of my storage should work (even better with checking the time stamp of each file), but I'd be happier if I have zfsstat-like tool that shows some file properties.

  Read the article

• Two network interfaces and two IP addresses on the same subnet in Linux

  - by Scott Duckworth

  I recently ran into a situation where I needed two IP addresses on the same subnet assigned to one Linux host so that we could run two SSL/TLS sites. My first approach was to use IP aliasing, e.g. using eth0:0, eth0:1, etc, but our network admins have some fairly strict settings in place for security that squashed this idea: They use DHCP snooping and normally don't allow static IP addresses. Static addressing is accomplished by using static DHCP entries, so the same MAC address always gets the same IP assignment. This feature can be disabled per switchport if you ask and you have a reason for it (thankfully I have a good relationship with the network guys and this isn't hard to do). With the DHCP snooping disabled on the switchport, they had to put in a rule on the switch that said MAC address X is allowed to have IP address Y. Unfortunately this had the side effect of also saying that MAC address X is ONLY allowed to have IP address Y. IP aliasing required that MAC address X was assigned two IP addresses, so this didn't work. There may have been a way around these issues on the switch configuration, but in an attempt to preserve good relations with the network admins I tried to find another way. Having two network interfaces seemed like the next logical step. Thankfully this Linux system is a virtual machine, so I was able to easily add a second network interface (without rebooting, I might add - pretty cool). A few keystrokes later I had two network interfaces up and running and both pulled IP addresses from DHCP. But then the problem came in: the network admins could see (on the switch) the ARP entry for both interfaces, but only the first network interface that I brought up would respond to pings or any sort of TCP or UDP traffic. After lots of digging and poking, here's what I came up with. It seems to work, but it also seems to be a lot of work for something that seems like it should be simple. Any alternate ideas out there? Step 1: Enable ARP filtering on all interfaces: # sysctl -w net.ipv4.conf.all.arp_filter=1 # echo "net.ipv4.conf.all.arp_filter = 1" >> /etc/sysctl.conf From the file networking/ip-sysctl.txt in the Linux kernel docs: arp_filter - BOOLEAN 1 - Allows you to have multiple network interfaces on the same subnet, and have the ARPs for each interface be answered based on whether or not the kernel would route a packet from the ARP'd IP out that interface (therefore you must use source based routing for this to work). In other words it allows control of which cards (usually 1) will respond to an arp request. 0 - (default) The kernel can respond to arp requests with addresses from other interfaces. This may seem wrong but it usually makes sense, because it increases the chance of successful communication. IP addresses are owned by the complete host on Linux, not by particular interfaces. Only for more complex setups like load- balancing, does this behaviour cause problems. arp_filter for the interface will be enabled if at least one of conf/{all,interface}/arp_filter is set to TRUE, it will be disabled otherwise Step 2: Implement source-based routing I basically just followed directions from http://lartc.org/howto/lartc.rpdb.multiple-links.html, although that page was written with a different goal in mind (dealing with two ISPs). Assume that the subnet is 10.0.0.0/24, the gateway is 10.0.0.1, the IP address for eth0 is 10.0.0.100, and the IP address for eth1 is 10.0.0.101. Define two new routing tables named eth0 and eth1 in /etc/iproute2/rt_tables: ... top of file omitted ... 1 eth0 2 eth1 Define the routes for these two tables: # ip route add default via 10.0.0.1 table eth0 # ip route add default via 10.0.0.1 table eth1 # ip route add 10.0.0.0/24 dev eth0 src 10.0.0.100 table eth0 # ip route add 10.0.0.0/24 dev eth1 src 10.0.0.101 table eth1 Define the rules for when to use the new routing tables: # ip rule add from 10.0.0.100 table eth0 # ip rule add from 10.0.0.101 table eth1 The main routing table was already taken care of by DHCP (and it's not even clear that its strictly necessary in this case), but it basically equates to this: # ip route add default via 10.0.0.1 dev eth0 # ip route add 130.127.48.0/23 dev eth0 src 10.0.0.100 # ip route add 130.127.48.0/23 dev eth1 src 10.0.0.101 And voila! Everything seems to work just fine. Sending pings to both IP addresses works fine. Sending pings from this system to other systems and forcing the ping to use a specific interface works fine (ping -I eth0 10.0.0.1, ping -I eth1 10.0.0.1). And most importantly, all TCP and UDP traffic to/from either IP address works as expected. So again, my question is: is there a better way to do this? This seems like a lot of work for a seemingly simple problem.

  Read the article

• What is the equivalent of 127.255.255.255 for OS/X machines so I can test broadcast udp packets without a network?

  - by JohnPristine

  I am trying to test my program that makes use of broadcast UDP (not multicast!). In Linux, I can use the 127.255.255.255:64651 address and everything works beautifully, in other words, I send a packet to 127.255.255.255:64651 and multiple clients listening on that port get the packet. A real broadcast example! Unfortunately on my OS/X machine (Mountain Lion) the same example does not work. Is there any way I can get 127.255.255.255 to work on mac machines? Any other solution to get broadcast working on my mac machine without a network? Note: It has to be broadcast, not multicast.

  Read the article

• Reimage PC: Myth or Fact to speeding up a slow PC?

  - by sunpech

  I have a 4-5 year old PC running Windows XP for software development at work. It struggles to run all development tools I need at the same time. Management feels I need to reimage my computer to "speed it up". The last time it was imaged was about 3 years ago. What resources books, websites, blogs, articles, etc are out there that supports/debunks this well known belief that reimaging an old PC running Windows XP will make it faster once again? A resource I remember reading is from Lifehacker.com: Windows Maintenance Tips: The Good, Bad And Useless

  Read the article

• Connectiong adsl router/modem and router with bridgemode

  - by Zvonko Telefonko

  I have one adsl modem/router which is not "top" of the line and it lack allot of options which I need. I was able to acquire one Cisco router recently which has all options that I need ( like DMZ, VPN, port forwarding, etc). I'm interested, if I connect the old modem/router to new Cisco router using bridge mode, will I be able to use all the features on the Cisco? For instance, the old router is lacking of port forward options. Does this mean that I will not be able to use port forwarding on Cisco router either or, since I will be using bridge mode, this will not affect Cisco router and it will work as the modem is in him? thank you

  Read the article

• How to open existing VMs in VirtualBox?

  - by Alex R

  VirtualBox seems to lack the obvious "File - Open" menu option. Frustrating! More details... I recently got a new workstation and I moved my VirtualBox and VMWare Player VMs from the old PC to the new. The VMWare Player VMs are a snap... you go to "File - Open a Virtual Machine...", find the .vmx files from the old PC, and voila! It's up and running. All the required files apparently are in the same folder. With VirtualBox there just doesn't seem to be a way to do that. Looks like VMs are tied to the original host in some magical/invisible way like registry entries, etc.

  Read the article

• Is it possible to interrupt or cancel the trash-delete process?

  - by pete

  I am connected to the company server, onsite not remote, which is Windows based. When, in the OS finder, I go to delete a file or directory that resides on the window-based server, the trash progress panel appears as usual. Not infrequently it will just hang there appearing to be active but no progress occurs on the progress bar. So the X is chosen to stop or cancel the process. A new panel appears, and while appearing to be active, again, just hangs there indefinitely. My lack of reputation prevents posting a screen shot - sorry. The question then is this: Is there a way via the Activity Monitor, Terminal, etc. to interrupt this deleting process in the Mac OS? Currently, I have to force shutdown and reboot to eradicate the ever-deleting panel. Finder relaunch does not solve and only eliminates the finder until I force reboot. Any assistance is appreciated. Thanks, Pete iMac, Mac OS X (10.6.8), i7-2.8ghz, 8gb ram

  Read the article

• Upgrading NAS hard drives

  - by Mihai Damian

  I was thinking of buying a NAS for home-usage. I've never used a NAS or had HDDs set up in Raids. Before I commit myself to moving all my data to a NAS I need to find out how difficult it is to upgrade and replace the NAS' hard drives. Suppose I set up a Raid 1 NAS with two 1TB hdds. At some point in the future I will use up all the space and will have to install two new 2TB hdds. Now I'll need to migrate the data from the old disks to the new ones. Will I have to hook up one of the old disks in a computer and copy all the data back in the NAS? Or can the migration be done using only the NAS? I realize the answer to the question might depend on the NAS model. Being a simple for-home solution I was thinking of getting something along the lines of D-link's 323.

  Read the article

• SATA Backward compatibility? [closed]

  - by Fladur

  Possible Duplicate: Can I connect a SATA-II hard drive to a SATA-I connection? Hello everyone One of my system is really old, but I still use it, right now, the HDD is and old IDE drive that is starting to fail (I got to many damaged sectors) and I'm planing to replace it. The motherboard supports Serial ATA 1 and I have a real nice offer on a SATA 2 drive, can I use that drive on a SATA 1 interface (obviously with reduced speed) just like a USB 2.0 device on a 1.0 port? Thanks in advance.

  Read the article

• How can I send a Wake on Wireless LAN (WoWLAN) / Wake on Demand request manually?

  - by pioto

  This is similar to, but not the same as, http://serverfault.com/questions/1721/is-wireless-wake-on-lan-possible. I know it is supposed to be possible. The question is, how do I do whatever the AirPort Basestation will do? All I can find so far is that supposedly I need to send something with Wireless Multimedia Extensions (WMM): Basically, I want to be able to wake up my Mac Mini remotely, probably using my Linux laptop. Does anyone know of a tool to do this? Basic Wake on LAN tools do not seem to be the right thing. I don't need the Sleep Proxy Service bit, because I already know the MAC address of the system I want to wake up.

  Read the article

• Server 2008 R2 .Net 4 Programs running from Network share won't work

  - by Lim

  we have several .Net Apps stored on a Network share on our old Server (Windows Server 2003). These Apps get called by Windows 7 32bit Clients and work perfectly fine. We recently wanted to upgrade our Server to Windows Server 2008 R2 and moved the Apps from the old share to our new share on the new Server. The problem started right afterwards since all of our .Net Programs won't start anymore from the new share (2008 R2). The Error that comes up is: "This application could not be started." and with a link to Microsoft: http://support.microsoft.com/kb/2715633 (This Error also shows up when i start a simple console HelloWorld from the server share created in VS2012) Does anyone have any Idea why this is not working anymore on the new Servershare? We've been searching for two days now with no result at all. Any Tips / Help / Questions appreciated :) Greetings Lim

  Read the article

• SQL Server 2005 Default Backup Plan

  - by tylerl

  I noticed that a newly imported database on SQLServer 2005 had configured itself (without my knowledge) to perform daily backups; but it's not deleting old files and quickly filling up the disk. I don't know how the backup job got configured (maybe that's something that gets transferred when you move a database?) but I'm having trouble modifying it. The backup runs as part of SQL Server Agent job called "Daily Backups". This job runs a package called "(SSIS Packages)\Maintenance Plans\Backup Plan" -- which I can't find. The "Management\Maintenance Plans" area for my server is empty. I imagine I could delete the existing plan and re-create it manually, but I was hoping to just modify what was already there, since all that's missing is deleting old files.

  Read the article

• Three ways to upload/post/convert iMovie to YouTube [closed]

  - by alexyu2010

  For Mac users, iMovie is probably a convenient tool for making, editing their own home movies so as to upload to YouTube for sharing with more people. However, uploading iMovie files to YouTube can't be always a smooth run, I did notice many people complaining about it. This article is delivered for guiding those who are haunted by the nightmare by providing three common ways to upload iMovie files to YouTube. YouTube and iMovie YouTube is the most popular video sharing website for users to upload, share and view videos. It empowers anyone with an Internet connection the ability to upload video clips and share them with friends, family and the world. Users are invited to leave comments, pick favourites, send messages to each other and watch videos sorted into subjects and channels. YouTube accepts videos uploaded in most container formats, including WMV (Windows Media Video), 3GP (Cell Phones), AVI (Windows), MOV (Mac), MP4 (iPod/PSP), FLV (Adobe Flash), MKV (H.264). These include video codecs such as MP4, MPEG and WMV. iMovie is a common video editing software application comes with every Mac for users to edit their own home movies. It imports video footage to the Mac using either the Firewire interface on most MiniDV format digital video cameras, the USB port, or by importing the files from a hard drive where users can edit the video clips, add titles, and add music. Since 1999, eight versions of iMovie have been released by Apple, each with its own functions and characteristic, and each of them deal with videos in a way more or less different. But the most common formats handled with iMovie if specialty discarded as far as to my research are MOV, DV, HDV, MPEG-4. Three ways for successful upload iMovie files to YouTube Solution one and solution two suitable for those who are 100 certainty with their iMovie files which are fully compatible with YouTube. For smooth uploading, you are required to get a YouTube account first. Solution 1: Directly upload iMovie to YouTube Step 1: Launch iMovie, select the project you want to upload in YouTube. Step 2: Go to the file menu, click Share, select Export Movie Step 3: Specify the output file name and directory and then type the video type and video size. Solution 2: Post iMovie to YouTube straightly Step 1: Launch iMovie, choose the project you want to post in YouTube Step 2: From the Share menu, choose YouTube Step 3: In the pop-up YouTube windows, specify the name of your YouTube account, the password, choose the Category and fill in the description and tags of the project. Tick Make this movie more private on the bottom of the window, if possible, to limit those who can view the project. Click Next, and then click Publish. iMovie will automatically export and upload the movie to YouTube. Step 4: Click Tell a Friend to email friends and your family about your film. You are also allowed to copy the URL from Tell a Friend window and paste it into an email you created in your favourite email application if you like. Anyone you send to email to will be able to follow the URL directly to your movie. Note: Videos uploaded to YouTube are limited to ten minutes in length and a file size of 2GB. Solution 3: Upload to iMovie after conversion If neither of the above mentioned method works, there is still a third way to turn to. Sometimes, your iMovie files may not be recognized by YouTube due to the versions of iMovie (settings and functions may varies among versions), video itself (video format difference because of file extension, resolution, video size and length), compatibility (videos that are completely incompatible with YouTube). In this circumstance, the best and reliable method is to convert your iMovie files to YouTube accepted files, iMovie to YouTube converter will be inevitably the ideal choice. iMovie to YouTube converter is an elaborately designed tool for convert iMovie files to YouTube workable WMV, 3GP, AVI, MOV, MP4, FLV, MKV for smooth uploading with hard-to-believe conversion speed and second to none output quality. It can also convert between almost all popular popular file formats like AVI, WMV, MPG, MOV, VOB, DV, MP4, FLV, 3GP, RM, ASF, SWF, MP3, AAC, AC3, AIFF, AMR, WAV, WMA etc so as to put on various portable devices, import to video editing software or play on vast amount video players. iMovie to YouTube converter can also served as an excellent video editing tool to meet your specific program requirements. For example, you can cut your video files to a certain length, or split your video files to smaller ones and select the proper resolution suitable for demands of YouTube by Clip or Settings separately. Crop allows you to cut off unwanted black edges from your videos. Besides, you can also have a good command of the whole process or snapshot your favourite pictures from the preview window. More can be expected if you have a try.

  Read the article

• How to recover Virtual Machines in Virtualbox?

  - by Bruce Connor

  For some reason, all of a sudden, all virtual machines are gone from the User Interface in virtual box. I suspect CCleaner has something to do with it, but that's not the point. Both the virtual hardisks and the .xml files for the machines are still in their respective folders. How can I use them to get my virtual machines back into virtualbox? I tried simply creating a new machine from the old virtual hardisks, and it worked with the ubuntu guest, but not with the windows one. Plus, it'd be nice to get my old machines back instead of having to create new ones, that would keep me from having to fix some shortcuts as well as reconfigure shared folders and other stuff. Thanks EDIT:Running Windows. [Solved]

  Read the article

< Previous Page | 273 274 275 276 277 278 279 280 281 282 283 284  | Next Page >