Search Results

Search found 7396 results on 296 pages for 'ms dos'.

Page 278/296 | < Previous Page | 274 275 276 277 278 279 280 281 282 283 284 285  | Next Page >

• Tunnel is up but cannot ping directly connected network

  - by drmanalo

  We configured a site-to-site VPN and here is the topology. I control the network on the left but not the one on the right. All devices in our network has public IPs. Server---ASA5505---Cisco887======Internet=====ASA5510---devices I can see the tunnel is up and can do extended ping using a loopback interface. From the 10.175 and 10.165 networks, they can also ping my loopback address. I can also dial in using a Cisco VPN client, and can connect to the devices on the right. #show crypto session Crypto session current status Interface: Vlan3 Profile: xxx-profile Session status: UP-ACTIVE Peer: 213.121.x.x port 500 IKEv1 SA: local 77.245.x.x/500 remote 213.121.x.x/500 Active IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.175.0.0/255.255.128.0 Active SAs: 0, origin: crypto map IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.165.0.0/255.255.192.0 Active SAs: 2, origin: crypto map #ping 10.165.29.39 source loopback 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.165.29.39, timeout is 2 seconds: Packet sent with a source address of 10.0.20.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 16/17/20 ms My problem is the devices on the right cannot reach my server. They could only ping the loopback address and nothing else. I'm pasting some diagnostics related to routing thinking perhaps routing is my issue. I can paste all the running-config on my side of network if needed. #show ip int brief Interface IP-Address OK? Method Status Protocol ATM0 unassigned YES NVRAM administratively down down Ethernet0 unassigned YES NVRAM administratively down down FastEthernet0 unassigned YES unset up up connected to ASA FastEthernet1 unassigned YES unset administratively down down FastEthernet2 unassigned YES unset administratively down down FastEthernet3 unassigned YES unset up up Loopback1 10.0.20.65 YES NVRAM up up Loopback2 10.0.20.1 YES NVRAM up up Virtual-Template1 77.245.x.x YES unset up down Virtual-Template2 77.245.x.x YES unset up down Vlan1 unassigned YES unset down down Vlan3 77.245.x.x YES NVRAM up up connected to the Internet #show run | section ip route ip route 0.0.0.0 0.0.0.0 77.245.x.x ip route 213.121.240.36 255.255.255.255 Vlan3 #show access-list Extended IP access list 102 10 permit ip 10.0.20.0 0.0.0.15 10.175.0.0 0.0.127.255 (3332 matches) 20 permit ip 10.0.20.0 0.0.0.15 10.165.0.0 0.0.63.255 (3498 matches) #show vlan-switch VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active 3 VLAN0003 active Fa0, Fa1, Fa2, Fa3 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup #show ip route Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP + - replicated route, % - next hop override Gateway of last resort is 77.245.x.x to network 0.0.0.0 S* 0.0.0.0/0 [1/0] via 77.245.x.x 10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks C 10.0.20.0/28 is directly connected, Loopback2 L 10.0.20.1/32 is directly connected, Loopback2 C 10.0.20.64/28 is directly connected, Loopback1 L 10.0.20.65/32 is directly connected, Loopback1 S 10.165.0.0/18 [1/0] via 213.121.x.x 77.0.0.0/8 is variably subnetted, 3 subnets, 3 masks S 77.0.0.0/8 [1/0] via 77.245.x.x C 77.245.x.x/29 is directly connected, Vlan3 L 77.245.x.x/32 is directly connected, Vlan3 213.121.x.0/32 is subnetted, 1 subnets S 213.121.x.x is directly connected, Vlan3 I read some of the posts here which lead to NATing issue but I'not sure of my next step. Should I translate my public address to private and route it to the loopback address? (only guessing) CISCO VPN site to site Site-to-Site VPN between two ASA 5505s only working in one direction Hope someone could help. Thanks in advance!

  Read the article

• Cannot ping Localhost so I can't shutdown Tomcat

  - by gav

  Hi, I installed Tomcat 6 using the tar-ball via wget. Startup of the server is fine but on shutdown I get a timeout exception. root@88:/usr/local/tomcat/logs# /usr/local/tomcat/bin/shutdown.sh Using CATALINA_BASE: /usr/local/tomcat Using CATALINA_HOME: /usr/local/tomcat Using CATALINA_TMPDIR: /usr/local/tomcat/temp Using JRE_HOME: /usr Using CLASSPATH: /usr/local/tomcat/bin/bootstrap.jar 30-Mar-2010 17:33:41 org.apache.catalina.startup.Catalina stopServer SEVERE: Catalina.stop: java.net.ConnectException: Connection timed out at java.net.PlainSocketImpl.socketConnect(Native Method) at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333) at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195) at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182) at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366) ... I read that this might be because I have a firewall blocking incoming connections on the shutdown port (8005). I have a default Ubuntu 9.04 installation running on a VPS with no rules in my iptables. How can I tell if that port is blocked? How can I check that the server is listening for connections on 8005? Bizarrely pinging localhost or the IP of my server fails from the server itself, whereas pinging the IP of my server from another machine succeeds. -------- EDIT -------- (In reply to Davey) Thanks for all the tips and suggestions! netstat -nlp Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:8005 0.0.0.0:* LISTEN 9611/java tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN 28505/mysqld tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN 9611/java tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN ... So we can see that tomcat is listening, I just don't seem to be able to reach it. root@88:/usr/local/tomcat# telnet localhost 8005 Trying 127.0.0.1... Trying to telnet to the port Hangs indefinitely. I have no rules in my iptables so I don't think it's a firewall thing. root@88:/usr/local/tomcat# iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination This is the contents of /etc/hosts 127.0.0.1 localhost.localdomain localhost # Auto-generated hostname. Please do not remove this comment. 88.198.31.14 88.198.31.14 88 88 But I still can't ping localhost... do I need to check a loopback device is enabled properly or something? (I'm unsure how to do that if you do say yes :)). root@88:/usr/local/tomcat# ping localhost PING localhost (127.0.0.1) 56(84) bytes of data. --- localhost ping statistics --- 7 packets transmitted, 0 received, 100% packet loss, time 5999ms Trying to find out what the loop back is configured as; root@88:~# ifconfig lo lo Link encap:Local Loopback LOOPBACK MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) SOLUTION THANKS TO DAVEY I needed to bring up the interface (Not sure why it wasn't running). ifconfig lo up did the trick. root@88:~# ifconfig lo up root@88:~# ifconfig lo lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@88:~# ping localhost PING localhost.localdomain (127.0.0.1) 56(84) bytes of data. 64 bytes from localhost.localdomain (127.0.0.1): icmp_seq=1 ttl=64 time=0.025 ms Thanks again, Gav

  Read the article

• PPTP connection fails with errors 800/806

  - by Mark S. Rasmussen

  I've got a client (Server 2008 R2) that won't connect to our production environment PPTP VPN server (Server 2003, running RRAS). The server is behind a firewall that has TCP1723 open as well as GRE. Other clients at our office are able to connect just fine. Our office is behind a Juniper SSG5-Serial firewall, but all outgoing traffic is allowed, and multiple other clients are able to connect to VPN servers without issues. I've also setup a completely different VPN server on another network outside of our office. The functioning clients connect just fine - the Server 2008 R2 machine doesn't. Thus it's definitely a problem with this machine in particular. I've rebooted it. I've disabled the firewall, no dice on either. I've run PPTPSRV and PPTPCLNT on the server/client and they're able to communicate perfectly - indicating there's no problem using neither TCP1723 nor GRE. The Server 2008 R2 machine is also running as a VPN server itself (incoming connection) and that's working perfectly. We have the issues no matter if there are active incoming connections or not. I'm not sure what my next debugging step would be; any suggestions? EDIT: The event log on the server has the following warning from RasMan: A connection between the VPN server and the VPN client xxx.xxx.xxx.xxx has been established, but the VPN connection cannot be completed. The most common cause for this is that a firewall or router between the VPN server and the VPN client is not configured to allow Generic Routing Encapsulation (GRE) packets (protocol 47). Verify that the firewalls and routers between your VPN server and the Internet allow GRE packets. Make sure the firewalls and routers on the user's network are also configured to allow GRE packets. If the problem persists, have the user contact the Internet service provider (ISP) to determine whether the ISP might be blocking GRE packets. Obviously this points to GRE being a potential problem. But seeing as I have other clients connectiong without problems, as well as PPTPSRV and PPTPCLNT being able to communicate, I'm suspecting this might be a red herring. EDIT: Here are the anonymized events logged by the client in chronological order: CoId={742CB15C-A7E0-47B7-8240-0EFA1139CBD9}: The user XXX\YYY has started dialing a VPN connection using a per-user connection profile named ZZZ. The connection settings are: Dial-in User = XXX\YYY VpnStrategy = PPTP DataEncryption = Require PrerequisiteEntry = AutoLogon = No UseRasCredentials = Yes Authentication Type = CHAP/MS-CHAPv2 Ipv4DefaultGateway = No Ipv4AddressAssignment = By Server Ipv4DNSServerAssignment = By Server Ipv6DefaultGateway = Yes Ipv6AddressAssignment = By Server Ipv6DNSServerAssignment = By Server IpDnsFlags = Register primary domain suffix IpNBTEnabled = Yes UseFlags = Private Connection ConnectOnWinlogon = No. CoId={742CB15C-A7E0-47B7-8240-0EFA1139CBD9}: The user XXX\YYY is trying to establish a link to the Remote Access Server for the connection named ZZZ using the following device: Server address/Phone Number = XXX.YYY.ZZZ.KKK Device = WAN Miniport (PPTP) Port = VPN3-4 MediaType = VPN. CoId={742CB15C-A7E0-47B7-8240-0EFA1139CBD9}: The user XXX\YYY has successfully established a link to the Remote Access Server using the following device: Server address/Phone Number = XXX.YYY.ZZZ.KKK Device = WAN Miniport (PPTP) Port = VPN3-4 MediaType = VPN. CoId={742CB15C-A7E0-47B7-8240-0EFA1139CBD9}: The link to the Remote Access Server has been established by user XXX\YYY. CoId={742CB15C-A7E0-47B7-8240-0EFA1139CBD9}: The user XXX\YYY dialed a connection named ZZZ which has failed. The error code returned on failure is 806. Running Wireshark on the client shows it trying and retrying to send a "71 Configuration Request" While the server shows the incoming client requests, but apparently without replying: Given that this is GRE traffic, I think rules out the GRE traffic being blocked. Question is, why doesn't the server reply? This is the Configuration Request the server receives from the non functioning client (meaning no response is sent to the client request): And this is the Configuration Request the server receives from the working client: To me they seem identical, except for differing keys and magic numbers, and the fact that one client receives a response while the other doesn't.

  Read the article

• Can't connect to samba

  - by Rick

  Windows 7, connecting to Samba shares I have a follow up question from the link above. I am running Samba 3.0.23d on FreeBSD is release 7.1 I changed the policies as described above but still cannot connect to the samba server with the windows 7 or a server 2008. I feel it is a problem with recognizing the new machines on the network. the windows machines can see the samba server, but cannot connect to it or view any of the files. After changing the security policies the samba server asked for network id and password but would not allow the machine to connect, said they were unknown username or bad password. Here is my current config file. there is no sign of encryption anywhere, should I just add the line? not sure what that would do elsewhere. Workgroup = WWOFFSET server string = WWO File Server (%v) security = server username map = /usr/local/etc/smb.users hosts allow = 10. 127. # If you want to automatically load your printer list rather # than setting them up individually then you'll need this ; load printers = yes # you may wish to override the location of the printcap file ; printcap name = /etc/printcap # on SystemV system setting printcap name to lpstat should allow # you to automatically obtain a printer list from the SystemV spool # system ; printcap name = lpstat # It should not be necessary to specify the print system type unless # it is non-standard. Currently supported print systems include: # bsd, cups, sysv, plp, lprng, aix, hpux, qnx ; printing = cups # Uncomment this if you want a guest account, you must add this to /etc/passwd # otherwise the user "nobody" is used ; guest account = pcguest # this tells Samba to use a separate log file for each machine # that connects log file = /var/log/samba/log.%m # Put a capping on the size of the log files (in Kb). max log size = 50 # Use password server option only with security = server # The argument list may include: # password server = My_PDC_Name [My_BDC_Name] [My_Next_BDC_Name] # or to auto-locate the domain controller/s # password server = * ; password server = <NT-Server-Name> password server = SERVER0 # Use the realm option only with security = ads # Specifies the Active Directory realm the host is part of ; realm = MY_REALM # Backend to store user information in. New installations should # use either tdbsam or ldapsam. smbpasswd is available for backwards # compatibility. tdbsam requires no further configuration. ; passdb backend = tdbsam ; passdb backend = smbpasswd # Using the following line enables you to customise your configuration # on a per machine basis. The %m gets replaced with the netbios name # of the machine that is connecting. # Note: Consider carefully the location in the configuration file of # this line. The included file is read at that point. ; include = /usr/local/etc/smb.conf.%m # Most people will find that this option gives better performance. # See the chapter 'Samba performance issues' in the Samba HOWTO Collection # and the manual pages for details. # You may want to add the following on a Linux system: # SO_RCVBUF=8192 SO_SNDBUF=8192 socket options = TCP_NODELAY # Configure Samba to use multiple interfaces # If you have multiple network interfaces then you must list them # here. See the man page for details. ; interfaces = 192.168.12.2/24 192.168.13.2/24 # Browser Control Options: # set local master to no if you don't want Samba to become a master # browser on your network. Otherwise the normal election rules apply ; local master = no # OS Level determines the precedence of this server in master browser # elections. The default value should be reasonable ; os level = 33 # Domain Master specifies Samba to be the Domain Master Browser. This # allows Samba to collate browse lists between subnets. Don't use this # if you already have a Windows NT domain controller doing this job ; domain master = yes # Preferred Master causes Samba to force a local browser election on startup # and gives it a slightly higher chance of winning the election ; preferred master = yes # Enable this if you want Samba to be a domain logon server for # Windows95 workstations. ; domain logons = yes # if you enable domain logons then you may want a per-machine or # per user logon script # run a specific logon batch file per workstation (machine) ; logon script = %m.bat # run a specific logon batch file per username ; logon script = %U.bat # Where to store roving profiles (only for Win95 and WinNT) # %L substitutes for this servers netbios name, %U is username # You must uncomment the [Profiles] share below ; logon path = \\%L\Profiles\%U # Windows Internet Name Serving Support Section: # WINS Support - Tells the NMBD component of Samba to enable it's WINS Server ; wins support = yes # WINS Server - Tells the NMBD components of Samba to be a WINS Client # Note: Samba can be either a WINS Server, or a WINS Client, but NOT both ; wins server = w.x.y.z # WINS Proxy - Tells Samba to answer name resolution queries on # behalf of a non WINS capable client, for this to work there must be # at least one WINS Server on the network. The default is NO. ; wins proxy = yes # DNS Proxy - tells Samba whether or not to try to resolve NetBIOS names # via DNS nslookups. The default is NO. dns proxy = no # charset settings ; display charset = ASCII ; unix charset = ASCII ; dos charset = ASCII # These scripts are used on a domain controller or stand-alone # machine to add or delete corresponding unix accounts ; add user script = /usr/sbin/useradd %u ; add group script = /usr/sbin/groupadd %g ; add machine script = /usr/sbin/adduser -n -g machines -c Machine -d /dev/null -s /bin/false %u ; delete user script = /usr/sbin/userdel %u ; delete user from group script = /usr/sbin/deluser %u %g ; delete group script = /usr/sbin/groupdel %g unix extensions = no

  Read the article

• Sendmail to local domain ignoring MX records (part 2)

  - by FractalizeR

  Hello. I have the exact problem, like in this post: http://serverfault.com/questions/25068/sendmail-to-local-domain-ignoring-mx-records I am also using email provider like GMail For Your Domain (which stores your mail and manages it). I am sending mail from my server directly, but receiving mail is done via Yandex (email provider). Since the server hosts forum, I prefer to send mail directly from it because using another mail provider can slow things. Also, when I send 300.000 emails to my subscribers, email provider will surely block me thinking I send spam. My DNS zone now is: ; ; GSMFORUM.RU ; $TTL 1H gsmforum.ru. SOA ns1.hc.ru. support.hc.ru. ( 2009122268 ; Serial 1H ; Refresh 30M ; Retry 1W ; Expire 1H ) ; Minimum gsmforum.ru. NS ns1.hc.ru. gsmforum.ru. NS ns2.hc.ru. @ A 79.174.68.223 *.gsmforum.ru. CNAME @ ns1 A 79.174.68.223 ns2 A 79.174.68.224 @ MX 10 mx.yandex.ru. mail CNAME domain.mail.yandex.net. yamail-xxxxxxxxx CNAME mail.yandex.ru. Server hostname is server.gsmforum.ru. May be this is the cause? Can someone explain the reason of the matter (the rules that make sendmail consider domain to be local)? Can I easily change *.gsmforum.ru. CNAME @ into *.gsmforum.ru. A 79.174.68.224 to solve this problem? [root@server ~]# cat /etc/mail/local-host-names localhost localhost.localdomain This server hosts gsmforum.ru so I cannot put it into another domain like David Mackintosh suggests. Putting domain in mailertable doesn't solve the problem also. sendmail -bt still shows, that address is local. DontProbeInterfaces is also set to true at sendmail config. M4 file follows: divert(-1)dnl dnl # dnl # This is the sendmail macro config file for m4. If you make changes to dnl # /etc/mail/sendmail.mc, you will need to regenerate the dnl # /etc/mail/sendmail.cf file by confirming that the sendmail-cf package is dnl # installed and then performing a dnl # dnl # make -C /etc/mail dnl # include(`/usr/share/sendmail-cf/m4/cf.m4')dnl VERSIONID(`setup for linux')dnl OSTYPE(`linux')dnl dnl # dnl # Do not advertize sendmail version. dnl # dnl define(`confSMTP_LOGIN_MSG', `$j Sendmail; $b')dnl dnl # dnl # default logging level is 9, you might want to set it higher to dnl # debug the configuration dnl # dnl define(`confLOG_LEVEL', `9')dnl dnl # dnl # Uncomment and edit the following line if your outgoing mail needs to dnl # be sent out through an external mail server: dnl # dnl define(`SMART_HOST', `smtp.your.provider')dnl dnl # define(`confDEF_USER_ID', ``8:12'')dnl dnl define(`confAUTO_REBUILD')dnl define(`confTO_CONNECT', `1m')dnl define(`confTRY_NULL_MX_LIST', `True')dnl define(`confDONT_PROBE_INTERFACES',`True') define(`PROCMAIL_MAILER_PATH', `/usr/bin/procmail')dnl define(`ALIAS_FILE', `/etc/aliases')dnl define(`STATUS_FILE', `/var/log/mail/statistics')dnl define(`UUCP_MAILER_MAX', `2000000')dnl define(`confUSERDB_SPEC', `/etc/mail/userdb.db')dnl define(`confPRIVACY_FLAGS', `authwarnings,novrfy,noexpn,restrictqrun')dnl define(`confAUTH_OPTIONS', `A')dnl dnl # dnl # The following allows relaying if the user authenticates, and disallows dnl # plaintext authentication (PLAIN/LOGIN) on non-TLS links dnl # dnl define(`confAUTH_OPTIONS', `A p')dnl dnl # dnl # PLAIN is the preferred plaintext authentication method and used by dnl # Mozilla Mail and Evolution, though Outlook Express and other MUAs do dnl # use LOGIN. Other mechanisms should be used if the connection is not dnl # guaranteed secure. dnl # Please remember that saslauthd needs to be running for AUTH. dnl # dnl TRUST_AUTH_MECH(`EXTERNAL DIGEST-MD5 CRAM-MD5 LOGIN PLAIN')dnl dnl define(`confAUTH_MECHANISMS', `EXTERNAL GSSAPI DIGEST-MD5 CRAM-MD5 LOGIN PLAIN')dnl dnl # dnl # Rudimentary information on creating certificates for sendmail TLS: dnl # cd /usr/share/ssl/certs; make sendmail.pem dnl # Complete usage: dnl # make -C /usr/share/ssl/certs usage dnl # dnl define(`confCACERT_PATH', `/etc/pki/tls/certs')dnl dnl define(`confCACERT', `/etc/pki/tls/certs/ca-bundle.crt')dnl dnl define(`confSERVER_CERT', `/etc/pki/tls/certs/sendmail.pem')dnl dnl define(`confSERVER_KEY', `/etc/pki/tls/certs/sendmail.pem')dnl dnl # dnl # This allows sendmail to use a keyfile that is shared with OpenLDAP's dnl # slapd, which requires the file to be readble by group ldap dnl # dnl define(`confDONT_BLAME_SENDMAIL', `groupreadablekeyfile')dnl dnl # dnl define(`confTO_QUEUEWARN', `4h')dnl dnl define(`confTO_QUEUERETURN', `5d')dnl dnl define(`confQUEUE_LA', `12')dnl dnl define(`confREFUSE_LA', `18')dnl define(`confTO_IDENT', `0')dnl dnl FEATURE(delay_checks)dnl FEATURE(`no_default_msa', `dnl')dnl FEATURE(`smrsh', `/usr/sbin/smrsh')dnl FEATURE(`mailertable', `hash -o /etc/mail/mailertable.db')dnl FEATURE(`virtusertable', `hash -o /etc/mail/virtusertable.db')dnl FEATURE(redirect)dnl FEATURE(always_add_domain)dnl FEATURE(use_cw_file)dnl FEATURE(use_ct_file)dnl dnl # dnl # The following limits the number of processes sendmail can fork to accept dnl # incoming messages or process its message queues to 20.) sendmail refuses dnl # to accept connections once it has reached its quota of child processes. dnl # dnl define(`confMAX_DAEMON_CHILDREN', `20')dnl dnl # dnl # Limits the number of new connections per second. This caps the overhead dnl # incurred due to forking new sendmail processes. May be useful against dnl # DoS attacks or barrages of spam. (As mentioned below, a per-IP address dnl # limit would be useful but is not available as an option at this writing.) dnl # dnl define(`confCONNECTION_RATE_THROTTLE', `3')dnl dnl # dnl # The -t option will retry delivery if e.g. the user runs over his quota. dnl # FEATURE(local_procmail, `', `procmail -t -Y -a $h -d $u')dnl FEATURE(`access_db', `hash -T<TMPF> -o /etc/mail/access.db')dnl FEATURE(`blacklist_recipients')dnl EXPOSED_USER(`root')dnl dnl # dnl # For using Cyrus-IMAPd as POP3/IMAP server through LMTP delivery uncomment dnl # the following 2 definitions and activate below in the MAILER section the dnl # cyrusv2 mailer. dnl # dnl define(`confLOCAL_MAILER', `cyrusv2')dnl dnl define(`CYRUSV2_MAILER_ARGS', `FILE /var/lib/imap/socket/lmtp')dnl dnl # dnl # The following causes sendmail to only listen on the IPv4 loopback address dnl # 127.0.0.1 and not on any other network devices. Remove the loopback dnl # address restriction to accept email from the internet or intranet. dnl # DAEMON_OPTIONS(`Name=MTA,Port=smtp') dnl # dnl # The following causes sendmail to additionally listen to port 587 for dnl # mail from MUAs that authenticate. Roaming users who can't reach their dnl # preferred sendmail daemon due to port 25 being blocked or redirected find dnl # this useful. dnl # dnl DAEMON_OPTIONS(`Port=submission, Name=MSA, M=Ea')dnl dnl # dnl # The following causes sendmail to additionally listen to port 465, but dnl # starting immediately in TLS mode upon connecting. Port 25 or 587 followed dnl # by STARTTLS is preferred, but roaming clients using Outlook Express can't dnl # do STARTTLS on ports other than 25. Mozilla Mail can ONLY use STARTTLS dnl # and doesn't support the deprecated smtps; Evolution <1.1.1 uses smtps dnl # when SSL is enabled-- STARTTLS support is available in version 1.1.1. dnl # dnl # For this to work your OpenSSL certificates must be configured. dnl # dnl DAEMON_OPTIONS(`Port=smtps, Name=TLSMTA, M=s')dnl dnl # dnl # The following causes sendmail to additionally listen on the IPv6 loopback dnl # device. Remove the loopback address restriction listen to the network. dnl # dnl DAEMON_OPTIONS(`port=smtp,Addr=::1, Name=MTA-v6, Family=inet6')dnl dnl # dnl # enable both ipv6 and ipv4 in sendmail: dnl # dnl DAEMON_OPTIONS(`Name=MTA-v4, Family=inet, Name=MTA-v6, Family=inet6') dnl # dnl # We strongly recommend not accepting unresolvable domains if you want to dnl # protect yourself from spam. However, the laptop and users on computers dnl # that do not have 24x7 DNS do need this. dnl # FEATURE(`accept_unresolvable_domains')dnl dnl # dnl FEATURE(`relay_based_on_MX')dnl dnl # dnl # Also accept email sent to "localhost.localdomain" as local email. dnl # LOCAL_DOMAIN(`localhost.localdomain')dnl dnl # dnl # The following example makes mail from this host and any additional dnl # specified domains appear to be sent from mydomain.com dnl # dnl MASQUERADE_AS(`mydomain.com')dnl dnl # dnl # masquerade not just the headers, but the envelope as well dnl # dnl FEATURE(masquerade_envelope)dnl dnl # dnl # masquerade not just @mydomainalias.com, but @*.mydomainalias.com as well dnl # dnl FEATURE(masquerade_entire_domain)dnl dnl # dnl MASQUERADE_DOMAIN(localhost)dnl dnl MASQUERADE_DOMAIN(localhost.localdomain)dnl dnl MASQUERADE_DOMAIN(mydomainalias.com)dnl dnl MASQUERADE_DOMAIN(mydomain.lan)dnl MAILER(smtp)dnl MAILER(procmail)dnl dnl MAILER(cyrusv2)dnl FEATURE(`dnsbl',`zen.spamhaus.org',`Rejected - your IP is blacklisted by http://www.spamhaus.org')

  Read the article

• ProFTPd server on Ubuntu getting access denied message when successfully authenticated?

  - by exxoid

  I have a Ubuntu box with a ProFTPD 1.3.4a Server, when I try to log in via my FTP Client I cannot do anything as it does not allow me to list directories; I have tried logging in as root and as a regular user and tried accessing different paths within the FTP Server. The error I get in my FTP Client is: Status: Retrieving directory listing... Command: CDUP Response: 250 CDUP command successful Command: PWD Response: 257 "/var" is the current directory Command: PASV Response: 227 Entering Passive Mode (172,16,4,22,237,205). Command: MLSD Response: 550 Access is denied. Error: Failed to retrieve directory listing Any idea? Here is the config of my proftpd: # # /etc/proftpd/proftpd.conf -- This is a basic ProFTPD configuration file. # To really apply changes, reload proftpd after modifications, if # it runs in daemon mode. It is not required in inetd/xinetd mode. # # Includes DSO modules Include /etc/proftpd/modules.conf # Set off to disable IPv6 support which is annoying on IPv4 only boxes. UseIPv6 off # If set on you can experience a longer connection delay in many cases. IdentLookups off ServerName "Drupal Intranet" ServerType standalone ServerIdent on "FTP Server ready" DeferWelcome on # Set the user and group that the server runs as User nobody Group nogroup MultilineRFC2228 on DefaultServer on ShowSymlinks on TimeoutNoTransfer 600 TimeoutStalled 600 TimeoutIdle 1200 DisplayLogin welcome.msg DisplayChdir .message true ListOptions "-l" DenyFilter \*.*/ # Use this to jail all users in their homes # DefaultRoot ~ # Users require a valid shell listed in /etc/shells to login. # Use this directive to release that constrain. # RequireValidShell off # Port 21 is the standard FTP port. Port 21 # In some cases you have to specify passive ports range to by-pass # firewall limitations. Ephemeral ports can be used for that, but # feel free to use a more narrow range. # PassivePorts 49152 65534 # If your host was NATted, this option is useful in order to # allow passive tranfers to work. You have to use your public # address and opening the passive ports used on your firewall as well. # MasqueradeAddress 1.2.3.4 # This is useful for masquerading address with dynamic IPs: # refresh any configured MasqueradeAddress directives every 8 hours <IfModule mod_dynmasq.c> # DynMasqRefresh 28800 </IfModule> # To prevent DoS attacks, set the maximum number of child processes # to 30. If you need to allow more than 30 concurrent connections # at once, simply increase this value. Note that this ONLY works # in standalone mode, in inetd mode you should use an inetd server # that allows you to limit maximum number of processes per service # (such as xinetd) MaxInstances 30 # Set the user and group that the server normally runs at. # Umask 022 is a good standard umask to prevent new files and dirs # (second parm) from being group and world writable. Umask 022 022 # Normally, we want files to be overwriteable. AllowOverwrite on # Uncomment this if you are using NIS or LDAP via NSS to retrieve passwords: # PersistentPasswd off # This is required to use both PAM-based authentication and local passwords AuthPAMConfig proftpd AuthOrder mod_auth_pam.c* mod_auth_unix.c # Be warned: use of this directive impacts CPU average load! # Uncomment this if you like to see progress and transfer rate with ftpwho # in downloads. That is not needed for uploads rates. # UseSendFile off TransferLog /var/log/proftpd/xferlog SystemLog /var/log/proftpd/proftpd.log # Logging onto /var/log/lastlog is enabled but set to off by default #UseLastlog on # In order to keep log file dates consistent after chroot, use timezone info # from /etc/localtime. If this is not set, and proftpd is configured to # chroot (e.g. DefaultRoot or <Anonymous>), it will use the non-daylight # savings timezone regardless of whether DST is in effect. #SetEnv TZ :/etc/localtime <IfModule mod_quotatab.c> QuotaEngine off </IfModule> <IfModule mod_ratio.c> Ratios off </IfModule> # Delay engine reduces impact of the so-called Timing Attack described in # http://www.securityfocus.com/bid/11430/discuss # It is on by default. <IfModule mod_delay.c> DelayEngine on </IfModule> <IfModule mod_ctrls.c> ControlsEngine off ControlsMaxClients 2 ControlsLog /var/log/proftpd/controls.log ControlsInterval 5 ControlsSocket /var/run/proftpd/proftpd.sock </IfModule> <IfModule mod_ctrls_admin.c> AdminControlsEngine off </IfModule> # # Alternative authentication frameworks # #Include /etc/proftpd/ldap.conf #Include /etc/proftpd/sql.conf # # This is used for FTPS connections # #Include /etc/proftpd/tls.conf # # Useful to keep VirtualHost/VirtualRoot directives separated # #Include /etc/proftpd/virtuals.con # A basic anonymous configuration, no upload directories. # <Anonymous ~ftp> # User ftp # Group nogroup # # We want clients to be able to login with "anonymous" as well as "ftp" # UserAlias anonymous ftp # # Cosmetic changes, all files belongs to ftp user # DirFakeUser on ftp # DirFakeGroup on ftp # # RequireValidShell off # # # Limit the maximum number of anonymous logins # MaxClients 10 # # # We want 'welcome.msg' displayed at login, and '.message' displayed # # in each newly chdired directory. # DisplayLogin welcome.msg # DisplayChdir .message # # # Limit WRITE everywhere in the anonymous chroot # <Directory *> # <Limit WRITE> # DenyAll # </Limit> # </Directory> # # # Uncomment this if you're brave. # # <Directory incoming> # # # Umask 022 is a good standard umask to prevent new files and dirs # # # (second parm) from being group and world writable. # # Umask 022 022 # # <Limit READ WRITE> # # DenyAll # # </Limit> # # <Limit STOR> # # AllowAll # # </Limit> # # </Directory> # # </Anonymous> # Include other custom configuration files Include /etc/proftpd/conf.d/ UseReverseDNS off <Global> RootLogin on UseFtpUsers on ServerIdent on DefaultChdir /var/www DeleteAbortedStores on LoginPasswordPrompt on AccessGrantMsg "You have been authenticated successfully." </Global> Any idea what could be wrong? Thanks for your help!

  Read the article

• Setting up VPN client: L2TP with IPsec

  - by zachar

  I've got to connect to vpn server. It works on Windows, but in Ubuntu 10.04 not. Number of options is confusing for me. There is the input that I have: IP Address of VPN Pre-shared key to authenticate Information that MS-CHAPv2 is used Login and Password to VPN I was trying to achive that with network manager and with L2TP IPsec VPN Manager 1.0.9 but at failed. There is some logged information from L2TP IPsec VPN Manager 1.0.9: Nov 09 15:21:46.854 ipsec_setup: Stopping Openswan IPsec... Nov 09 15:21:48.088 Stopping xl2tpd: xl2tpd. Nov 09 15:21:48.132 ipsec_setup: Starting Openswan IPsec U2.6.23/K2.6.32-49-generic... Nov 09 15:21:48.308 ipsec__plutorun: Starting Pluto subsystem... Nov 09 15:21:48.318 ipsec__plutorun: adjusting ipsec.d to /etc/ipsec.d Nov 09 15:21:48.338 ipsec__plutorun: 002 added connection description "my_vpn_name" Nov 09 15:21:48.348 ipsec__plutorun: 003 NAT-Traversal: Trying new style NAT-T Nov 09 15:21:48.348 ipsec__plutorun: 003 NAT-Traversal: ESPINUDP(1) setup failed for new style NAT-T family IPv4 (errno=19) Nov 09 15:21:48.349 ipsec__plutorun: 003 NAT-Traversal: Trying old style NAT-T Nov 09 15:21:48.994 104 "my_vpn_name" #1: STATE_MAIN_I1: initiate Nov 09 15:21:48.994 003 "my_vpn_name" #1: received Vendor ID payload [RFC 3947] method set to=109 Nov 09 15:21:48.994 003 "my_vpn_name" #1: received Vendor ID payload [Dead Peer Detection] Nov 09 15:21:48.994 106 "my_vpn_name" #1: STATE_MAIN_I2: sent MI2, expecting MR2 Nov 09 15:21:48.994 003 "my_vpn_name" #1: NAT-Traversal: Result using RFC 3947 (NAT-Traversal): i am NATed Nov 09 15:21:48.994 108 "my_vpn_name" #1: STATE_MAIN_I3: sent MI3, expecting MR3 Nov 09 15:21:48.994 004 "my_vpn_name" #1: STATE_MAIN_I4: ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=oakley_3des_cbc_192 prf=oakley_sha group=modp1024} Nov 09 15:21:48.995 117 "my_vpn_name" #2: STATE_QUICK_I1: initiate Nov 09 15:21:48.995 004 "my_vpn_name" #2: STATE_QUICK_I2: sent QI2, IPsec SA established transport mode {ESP=>0x0c96795d <0x483e1a42 xfrm=AES_128-HMAC_SHA1 NATOA=none NATD=none DPD=none} Nov 09 15:21:49.996 [ERROR 210] Failed to open l2tp control file 'c my_vpn_name' and from syslog: Nov 9 15:21:46 o99 L2tpIPsecVpnControlDaemon: Opening client connection Nov 9 15:21:46 o99 L2tpIPsecVpnControlDaemon: Executing command ipsec setup stop Nov 9 15:21:46 o99 ipsec_setup: Stopping Openswan IPsec... Nov 9 15:21:48 o99 kernel: [ 4350.245171] NET: Unregistered protocol family 15 Nov 9 15:21:48 o99 ipsec_setup: ...Openswan IPsec stopped Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Command ipsec setup stop finished with exit code 0 Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Executing command invoke-rc.d xl2tpd stop Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Command invoke-rc.d xl2tpd stop finished with exit code 0 Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Opening client connection Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Closing client connection Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Executing command ipsec setup start Nov 9 15:21:48 o99 kernel: [ 4350.312483] NET: Registered protocol family 15 Nov 9 15:21:48 o99 ipsec_setup: Starting Openswan IPsec U2.6.23/K2.6.32-49-generic... Nov 9 15:21:48 o99 ipsec_setup: Using NETKEY(XFRM) stack Nov 9 15:21:48 o99 kernel: [ 4350.410774] Initializing XFRM netlink socket Nov 9 15:21:48 o99 kernel: [ 4350.413601] padlock: VIA PadLock not detected. Nov 9 15:21:48 o99 kernel: [ 4350.427311] padlock: VIA PadLock Hash Engine not detected. Nov 9 15:21:48 o99 kernel: [ 4350.441533] padlock: VIA PadLock not detected. Nov 9 15:21:48 o99 ipsec_setup: ...Openswan IPsec started Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Command ipsec setup start finished with exit code 0 Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Executing command invoke-rc.d xl2tpd start Nov 9 15:21:48 o99 ipsec__plutorun: adjusting ipsec.d to /etc/ipsec.d Nov 9 15:21:48 o99 pluto: adjusting ipsec.d to /etc/ipsec.d Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Command invoke-rc.d xl2tpd start finished with exit code 0 Nov 9 15:21:48 o99 ipsec__plutorun: 002 added connection description "my_vpn_name" Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Executing command ipsec auto --ready Nov 9 15:21:48 o99 ipsec__plutorun: 003 NAT-Traversal: Trying new style NAT-T Nov 9 15:21:48 o99 ipsec__plutorun: 003 NAT-Traversal: ESPINUDP(1) setup failed for new style NAT-T family IPv4 (errno=19) Nov 9 15:21:48 o99 ipsec__plutorun: 003 NAT-Traversal: Trying old style NAT-T Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Command ipsec auto --ready finished with exit code 0 Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Executing command ipsec auto --up my_vpn_name Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Command ipsec auto --up my_vpn_name finished with exit code 0 Nov 9 15:21:49 o99 L2tpIPsecVpnControlDaemon: Closing client connection Can anyone tell me something more about that? Where is the mistake?

  Read the article

• ASA 5505 stops local internet when connected to VPN

  - by g18c

  Hi I have a Cisco ASA router running firmware 8.2(5) which hosts an internal LAN on 192.168.30.0/24. I have used the VPN Wizard to setup L2TP access and I can connect in fine from a Windows box and can ping hosts behind the VPN router. However, when connected to the VPN I can no longer ping out to my internet or browse web pages. I would like to be able to access the VPN, and also browse the internet at the same time - I understand this is called split tunneling (have ticked the setting in the wizard but to no effect) and if so how do I do this? Alternatively, if split tunneling is a pain to setup, then making the connected VPN client have internet access from the ASA WAN IP would be OK. Thanks, Chris names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.30.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 208.74.158.58 255.255.255.252 ! ftp mode passive access-list inside_nat0_outbound extended permit ip any 10.10.10.0 255.255.255.128 access-list inside_nat0_outbound extended permit ip 192.168.30.0 255.255.255.0 192.168.30.192 255.255.255.192 access-list DefaultRAGroup_splitTunnelAcl standard permit 192.168.30.0 255.255.255.0 access-list DefaultRAGroup_splitTunnelAcl_1 standard permit 192.168.30.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool LANVPNPOOL 192.168.30.220-192.168.30.249 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 192.168.30.0 255.255.255.0 route outside 0.0.0.0 0.0.0.0 208.74.158.57 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.30.0 255.255.255.0 inside snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 TRANS_ESP_3DES_SHA crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.30.3 vpn-tunnel-protocol l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl_1 username user password Cj7W5X7wERleAewO8ENYtg== nt-encrypted privilege 0 tunnel-group DefaultRAGroup general-attributes address-pool LANVPNPOOL default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context : end

  Read the article

• How to delete files and folders that cannot be deleted?

  - by glenneroo

  I have a backup copy of a previous Windows' Documents and Settings folder which only contains my original user and within 2 more directories: Favorites and Local Settings. When I try to delete Local Settings I get this error: When I try to delete Favorites, I get this error: I ran this in a cmd shell: attrib *.* -r -a -s -h /s ...but it did not help, nor did it return any errors/warnings. I used Unlocker v1.8.5 and LockHunter repeatedly at multiple levels to see if any files are in use, but both always say: No Files Locked. Update #1: I was able to rename the directory, which now gives me this warning before (trying to) delete: If I press Yes (or Yes to All) then I get this error: Update #2: I let chkdsk /f run which required a reboot since it's on my primary system partition. During Stage 2 scanning, I received about 40 of these: Deleting an index entry from index $0 of file 25. ...followed by: Deleting index entry cookies in index $I30 of file 37576. ...but I still get the first error dialog above when trying to delete. I ran chkdsk again, this time: chkdsk /f /r. Produced no messages. Same result when deleting. Update #3: Digging deeper, the 99 is the name of one of many directories located deep in here: C:\Documents and Settings.OLD\User\Local Settings\Application Data\Microsoft\Messenger\[email protected]\SharingMetadata\[email protected]\DFSR\Staging\CS{D4E4AE55-B5E2-F03B-5189-6C4DA6E41788}\ Inside each of those directories were files with names such as: 2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-Downloaded.frx I noticed that, unlike all the directories, I couldn't rename any of these files. I also noticed that the file + dir names were extremely long: Original directory = 194 characters Filenames = 100+ characters Together the length exceeds the 255-char limit which is bad and would explain the error message I posted in Update #1. Partial Solution: Rename all directories until the total path length is less than 100. Afterwards I was able to rename the .frx files, not to mention delete everything inside the Local Settings directory. This is only a partial solution because these (empty) directories are still not deleteable, C:\1\2\Favorites\Wien\What To Do.. C:\1\2\Favorites\Photography\FIRE Same error as above: Here is what Explorer properties shows for both folders: Update #4 (another partial solution): Using harrymc's answer combined with thoroughly reading through this amazing MS-KB article which contains nearly everyone's idea and then some, inconspicuously titled: You cannot delete a file or a folder on an NTFS file system volume. I was able to delete the 2nd folder C:\1\2\Favorites\Photography\FIRE - the problem being that there was an invisible trailing space at the end. I got lucky when I did an auto-complete whilst playing around with the del "\\?\<path>" command which he suggested. NOTE: A normal del did NOT work, nor did deleting from explorer. Now all that is left is the first directory C:\1\2\Favorites\Wien\What To Do.. (yes I tried endlessly with multiple combinations of the above solution ;) Keep 'em coming! =)

  Read the article

• "Service Unavailable" when browsing to static HTML page in non-application IIS website on Windows 2003 (possibly SharePoint WSS 2.0 related?)

  - by Jordan Rieger

  Background: My client has an old Pentium III Windows 2003 server whose 16/36 GB disks are dying. On it he has a database-driven web site and email application that needs further customization by a developer (me). First we need to get it working on the new server. The original developer is no longer available to provide a system setup guide. So my client got a tech who imaged the old drives over to the new server and managed to get it booting. But the IIS-driven site no longer works. In fact it seems that IIS itself does not work. Problem: Service Unavailable when attempting to browse from the server itself to the URL for a local Web Site called test which I setup in IIS to serve a single static index.htm file. This I did to isolate the problem, and eliminate the client's application from the equation. The site is setup on port 80 with the host header "test.myclientsdomain.com", and I used the etc\hosts file to point that host at the local IP. I know the host entry took effect because I can ping it. When doing an iisreset, I get: Attempting start... Restart attempt failed. IIS Admin Service or a service dependent on IIS Admin is not active. It most likely failed to start, which may mean that it's disabled. Despite this message, the services all stay in the Started state. The only relevant System event logs I found are: Event Type: Error Event Source: W3SVC Event Category: None Event ID: 1002 Date: 11/4/2012 Time: 11:04:47 PM User: N/A Computer: ALPHA1 Description: Application pool 'DefaultAppPool' is being automatically disabled due to a series of failures in the process(es) serving that application pool. Event Type: Error Event Source: W3SVC Event Category: None Event ID: 1039 Date: 11/4/2012 Time: 11:13:12 PM User: N/A Computer: ALPHA1 Description: A process serving application pool 'DefaultAppPool' reported a failure. The process id was '5636'. The data field contains the error number. Data: 0000: 7e 00 07 80 ~.. And one Application event log: Event Type: Error Event Source: Windows SharePoint Services 2.0 Event Category: None Event ID: 1000 Date: 11/4/2012 Time: 11:34:04 PM User: N/A Computer: ALPHA1 Description: #50070: Unable to connect to the database STS_Config on ALPHA2\SharePoint. Check the database connection information and make sure that the database server is running. That last log tells me that the tech may have initially tried to have both the old and the new server running, by renaming the new server from ALPHA1 to ALPHA2. And perhaps SharePoint grabbed onto that change, and now can't tell that the machine name has been switched back to the old ALPHA1. But why would SharePoint interfere with a static IIS web site serving a single HTML file? The test site is not even within an Application pool (I clicked the Remove button.) What I have tried/eliminated: No relevant services seem to be disabled: IIS Admin, WWW Publishing, Sharepoint Timer Giving Full Control to All Users/Everyone on the c:\inetpub\test folder serving my test site. I can connect to and query the local SharePoint config database (ALPHA1\SHAREPOINT\STS_CONFIG) from SSMS. But when I try to do stsadm -o setconfigdb -connect -databaseserver ALPHA1\SHAREPOINT it tells me The SharePoint admininstration port does not exist. Please use stsadm.exe to create it. And when I do that, using the port 9487 specified in the IIS SharePoint Admin site config, it tells me the port is already in use. Needless to say, simply browsing to the admin site gives me a similar error about being unable to reach the config database. I didn't want to go further down the SharePoint path as it may be completed unrelated to my IIS issue, and I don't even know yet if SharePoint is required for this application to work. The app itself is ASP.Net/C#/Silverlight and a little MS Word integration (maybe that's where the SharePoint stuff comes in.)

  Read the article

• Hosed Windows 7 permissons

  - by Anthony

  Here is the most interesting thing I've noticed since the problems started: If I go into a control panel/system module (in this case the Resource Monitor) that has a "Check Online" type option, Firefox (my default browser) opens right up without a problem. But if I just start Firefox from any shortcuts (start menu, desktop, etc), the Firefox process starts up (and the start menu icon starts glowing) only to end without notice a few seconds later. Possibly related: If I start up in Safe-Mode (w/o Networking, but haven't tried with yet), I can start up FF or Chrome just fine, but if I attempt to open Chrome normally, I get a permissions error. Opera and Safari seem to be okay (mostly). Safari crashes when I try to download any files. All of the above leads me to believe that some (but clearly not all) core files have messed up permissions. Or rather, that I no longer have permission. System still does, based on Firefox opening without fail when the system initiates it. I've run MS Forefront once in normal mode, Malwarebytes twice in normal mode and once in safe-mode. One trojan found and deleted, but the problem persists. Two other things worth mentioning: I accidentally duplicated my library... I thought I'd try to add the "Internet" folder to my start menu, next to music and downloads. The first advanced thing I tried was "create new library". I clearly misunderstood what this means. I thought it was a way to add virtual folders to the library (which I thought, in turn, would allow me to choose it as a link on the start menu), but instead it recreated my already existing user folder, AppData and all. I didn't notice this until today. Then I tried setting permissions for my User folder to full control, recursively... Confused but not giving up,I thought I could maybe create a shortcut to the NetHood folder manually, but instead got hit with an access denied error. So I tried to change the permission levels for all sub-folders to my user folder so that I had full control. I got several access denied errors along the way. At this point I gave up, went out, ended up caught in the rain and stuck on a friend's couch and showing up late for work the next day. Thanks for nothing, Microsoft. When I finally got home today (20 hours later), I noticed that Firefox was acting really strange. I tried opening Chrome to see if the problem was client side or server side, and instead got the above-mentioned "you don't have permission to open this program" alert. And I think that's the whole story. Oh, I also did a system restore, but not chose a point from this morning (an auto update), and it worked but the problem wasn't fixed. And then all the earlier restore points were gone. So the questions are: a) is there a way to set the admin and user privs back to "default"? b) would this, in anyone's expert opinion, fix the problems I'm having? c) how come being logged in as an admin isn't the same as being logged in with admin privs? It seems that half the time I have to do run as admin for fairy standard things because i'm being treated as me-theuser and not me-theadmin. Thanks for reading.

  Read the article

• mySQL Optimization Suggestions

  - by Brian Schroeter

  I'm trying to optimize our mySQL configuration for our large Magento website. The reason I believe that mySQL needs to be configured further is because New Relic has shown that our SELECT queries are taking a long time (20,000+ ms) in some categories. I ran MySQLTuner 1.3.0 and got the following results... (Disclaimer: I restarted mySQL earlier after tweaking some settings, and so the results here may not be 100% accurate): >> MySQLTuner 1.3.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering [OK] Currently running supported MySQL version 5.5.37-35.0 [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +ARCHIVE +BLACKHOLE +CSV -FEDERATED +InnoDB +MRG_MYISAM [--] Data in MyISAM tables: 7G (Tables: 332) [--] Data in InnoDB tables: 213G (Tables: 8714) [--] Data in PERFORMANCE_SCHEMA tables: 0B (Tables: 17) [--] Data in MEMORY tables: 0B (Tables: 353) [!!] Total fragmented tables: 5492 -------- Security Recommendations ------------------------------------------- [!!] User '@host5.server1.autopartsnetwork.com' has no password set. [!!] User '@localhost' has no password set. [!!] User 'root@%' has no password set. -------- Performance Metrics ------------------------------------------------- [--] Up for: 5h 3m 4s (5M q [317.443 qps], 42K conn, TX: 18B, RX: 2B) [--] Reads / Writes: 95% / 5% [--] Total buffers: 35.5G global + 184.5M per thread (1024 max threads) [!!] Maximum possible memory usage: 220.0G (174% of installed RAM) [OK] Slow queries: 0% (6K/5M) [OK] Highest usage of available connections: 5% (61/1024) [OK] Key buffer size / total MyISAM indexes: 512.0M/3.1G [OK] Key buffer hit rate: 100.0% (102M cached / 45K reads) [OK] Query cache efficiency: 66.9% (3M cached / 5M selects) [!!] Query cache prunes per day: 3486361 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 812K sorts) [!!] Joins performed without indexes: 1328 [OK] Temporary tables created on disk: 11% (126K on disk / 1M total) [OK] Thread cache hit rate: 99% (61 created / 42K connections) [!!] Table cache hit rate: 19% (9K open / 49K opened) [OK] Open file limit used: 2% (712/25K) [OK] Table locks acquired immediately: 100% (5M immediate / 5M locks) [!!] InnoDB buffer pool / data size: 32.0G/213.4G [OK] InnoDB log waits: 0 -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Reduce your overall MySQL memory footprint for system stability Enable the slow query log to troubleshoot bad queries Increasing the query_cache size over 128M may reduce performance Adjust your join queries to always utilize indexes Increase table_cache gradually to avoid file descriptor limits Read this before increasing table_cache over 64: http://bit.ly/1mi7c4C Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 512M) [see warning above] join_buffer_size (> 128.0M, or always use indexes with joins) table_cache (> 12288) innodb_buffer_pool_size (>= 213G) My my.cnf configuration is as follows... [client] port = 3306 [mysqld_safe] nice = 0 [mysqld] tmpdir = /var/lib/mysql/tmp user = mysql port = 3306 skip-external-locking character-set-server = utf8 collation-server = utf8_general_ci event_scheduler = 0 key_buffer = 512M max_allowed_packet = 64M thread_stack = 512K thread_cache_size = 512 sort_buffer_size = 24M read_buffer_size = 8M read_rnd_buffer_size = 24M join_buffer_size = 128M # for some nightly processes client sessions set the join buffer to 8 GB auto-increment-increment = 1 auto-increment-offset = 1 myisam-recover = BACKUP max_connections = 1024 # max connect errors artificially high to support behaviors of NetScaler monitors max_connect_errors = 999999 concurrent_insert = 2 connect_timeout = 5 wait_timeout = 180 net_read_timeout = 120 net_write_timeout = 120 back_log = 128 # this table_open_cache might be too low because of MySQL bugs #16244691 and #65384) table_open_cache = 12288 tmp_table_size = 512M max_heap_table_size = 512M bulk_insert_buffer_size = 512M open-files-limit = 8192 open-files = 1024 query_cache_type = 1 # large query limit supports SOAP and REST API integrations query_cache_limit = 4M # larger than 512 MB query cache size is problematic; this is typically ~60% full query_cache_size = 512M # set to true on read slaves read_only = false slow_query_log_file = /var/log/mysql/slow.log slow_query_log = 0 long_query_time = 0.2 expire_logs_days = 10 max_binlog_size = 1024M binlog_cache_size = 32K sync_binlog = 0 # SSD RAID10 technically has a write capacity of 10000 IOPS innodb_io_capacity = 400 innodb_file_per_table innodb_table_locks = true innodb_lock_wait_timeout = 30 # These servers have 80 CPU threads; match 1:1 innodb_thread_concurrency = 48 innodb_commit_concurrency = 2 innodb_support_xa = true innodb_buffer_pool_size = 32G innodb_file_per_table innodb_flush_log_at_trx_commit = 1 innodb_log_buffer_size = 2G skip-federated [mysqldump] quick quote-names single-transaction max_allowed_packet = 64M I have a monster of a server here to power our site because our catalog is very large (300,000 simple SKUs), and I'm just wondering if I'm missing anything that I can configure further. :-) Thanks!

  Read the article

• Network config / gear question

  - by mcgee1234

  I have been tasked with setting up a fairly straightforward rack in a data center (we do not even need a whole rack, but this is the smallest allotment available). In a nutshell, 4 to 6 servers need to be able to reach 2 (maybe 3) vendors. The servers needs to be reachable over the internet. A little more detail - the networks the servers need to reach are inside of the data center, and are "trusted". Connections to these networks will be achieved through intra data center cross connects. It is kind of like a manufacturing line where we receive data from one vendor (burst-able up to 200 Mbits), churn through it on the servers, and then send out data to another vendor (bursts up to 20 Mbits). This series of events is very latency sensitive, so much so that it is common practice not to use NAT or a firewall on these segments (or so I hear). To reach the servers over the internet, I plan to use a site to site VPN. (This part is only relevant as far as hardware selection goes). I have 2 configurations in mind: Cisco 2911 (2921) (with the additional wan ports module) and a layer 2 switch - in this scenario, I would use the router also for VPN. Cisco 3560 layer 3 switch to interconnect the networks inside of the data center and an ASA 5510 (which is total overkill, but the 5505 is not rack mountable) as a firewall for the Wan side (internet) and VPN. I envision the setup to be as follows: Internet - ASA - 3560 Vendors - 3560 - Servers The general idea is that the ASA acts as a firewall and VPN device and the 3560 does all the heavy lifting. The first is a fairly traditional setup but my concern is performance. The second is somewhat unorthodox in that the vendors are directly connected to the layer 3 switch without passing through a firewall. Based on my understanding however, a layer 3 switch will perform substantially better as it will do hardware (ASIC) vs. software switching. (Note that number 2 is a little over the budget, but not unworkable (double negative, ugh)) Since this is my first time dealing with a data center, I am not sure what the IP space is going to look like. I suspect I will retain a block(s) of public IPs, vlan them to individual interfaces for the vendor connections and the servers (which will not reachable from the wan side of course) and setup routing on the switch. So here are my questionss: Is there a substantial performance difference between 1 and 2, i.e. hardware based switching on a layer 3 vs a software base on the 2911? I have trolled the internet and found a lot of Cisco literature, but nothing that I could really use to get a good handle. The vendors we connect to are secure and trusted (famous last words) and as I understand it, it is common practice not to NAT or firewall these connections (because of the aforementioned latency sensitivity). But what what kind of latency are we really talking about if I push the data through a router (or even ASA for that matter)? For our purposes, 5 ms will not kill us, 20 or 30 can be very costly. Others measure in microseconds, but they are out of our league. Is there any issues with using public IPs on a layer 3 switch? I am certainly not married to either of these configs, and I am totally open to any ideas. My knowledge (and I use the term loosely) is largely from books so I welcome any advice / insight. Thanks in advance.

  Read the article

• my asp.net mvc 2.0 application fails with error "No parameterless constructor defined for this objec

  - by loviji

  Hello, i'm new in asp.net mvc 2. I'm trying to list all data from one table(ms sql server table). as ORM I use Entity Framework. now, I'm tried to write something to do this: Model: private uqsEntities _uqsEntity; public permissionRepository(uqsEntities uqsEntity) { _uqsEntity = uqsEntity; } public IEnumerable<userPermissions> getAllData() { return _uqsEntity.userPermissions; } controller: private DataManager _dataManager; public ManagePermissionsController(DataManager datamanager) { _dataManager = datamanager; } public ActionResult Index() { return RedirectToAction("List"); } [AcceptVerbs(HttpVerbs.Get)] public ActionResult List() { return List(null); } [AcceptVerbs(HttpVerbs.Post)] public ActionResult List(int? userID) { return View(_dataManager.Permission.getAllData().ToList()); } Route: routes.MapRoute( "ManagePerm", // Route name "{controller}/{action}/{id}", // URL with parameters new { controller = "ManagePermissions", action = "Index"}, new string[] { "uqs.Controllers" } // Parameter defaults ); and View automatically generated by Visual Studio(in action mouse right-click). when I run app. , my app. fails. No parameterless constructor defined for this object. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.MissingMethodException: No parameterless constructor defined for this object. Source Error: An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace: [MissingMethodException: No parameterless constructor defined for this object.] System.RuntimeTypeHandle.CreateInstance(RuntimeType type, Boolean publicOnly, Boolean noCheck, Boolean& canBeCached, RuntimeMethodHandle& ctor, Boolean& bNeedSecurityCheck) +0 System.RuntimeType.CreateInstanceSlow(Boolean publicOnly, Boolean fillCache) +86 System.RuntimeType.CreateInstanceImpl(Boolean publicOnly, Boolean skipVisibilityChecks, Boolean fillCache) +230 System.Activator.CreateInstance(Type type, Boolean nonPublic) +67 System.Web.Mvc.DefaultControllerFactory.GetControllerInstance(RequestContext requestContext, Type controllerType) +80 [InvalidOperationException: An error occurred when trying to create a controller of type 'uqs.Controllers.ManagePermissionsController'. Make sure that the controller has a parameterless public constructor.] System.Web.Mvc.DefaultControllerFactory.GetControllerInstance(RequestContext requestContext, Type controllerType) +190 System.Web.Mvc.DefaultControllerFactory.CreateController(RequestContext requestContext, String controllerName) +68 System.Web.Mvc.MvcHandler.ProcessRequestInit(HttpContextBase httpContext, IController& controller, IControllerFactory& factory) +118 System.Web.Mvc.MvcHandler.BeginProcessRequest(HttpContextBase httpContext, AsyncCallback callback, Object state) +46 System.Web.Mvc.MvcHandler.BeginProcessRequest(HttpContext httpContext, AsyncCallback callback, Object state) +63 System.Web.Mvc.MvcHandler.System.Web.IHttpAsyncHandler.BeginProcessRequest(HttpContext context, AsyncCallback cb, Object extraData) +13 System.Web.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() +8679186 System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +155 please, somebody, help me to catch problem.

  Read the article

• The application called an interface that was marshalled for a different thread

  - by X-Ray

  i'm writing a delphi app that communicates with excel. one thing i noticed is that if i call the Save method on the Excel workbook object, it can appear to hang because excel has a dialog box open for the user. i'm using the late binding. i'd like for my app to be able to notice when Save takes several seconds and then take some kind of action like show a dialog box telling this is what's happening. i figured this'd be fairly easy. all i'd need to do is create a thread that calls Save and have that thread call Excel's Save routine. if it takes too long, i can take some action. procedure TOfficeConnect.Save; var Thread:TOfficeHangThread; begin // spin off as thread so we can control timeout Thread:=TOfficeSaveThread.Create(m_vExcelWorkbook); if WaitForSingleObject(Thread.Handle, 5 {s} * 1000 {ms/s})=WAIT_TIMEOUT then begin Thread.FreeOnTerminate:=true; raise Exception.Create(_('The Office spreadsheet program seems to be busy.')); end; Thread.Free; end; TOfficeSaveThread = class(TThread) private { Private declarations } m_vExcelWorkbook:variant; protected procedure Execute; override; procedure DoSave; public constructor Create(vExcelWorkbook:variant); end; { TOfficeSaveThread } constructor TOfficeSaveThread.Create(vExcelWorkbook:variant); begin inherited Create(true); m_vExcelWorkbook:=vExcelWorkbook; Resume; end; procedure TOfficeSaveThread.Execute; begin m_vExcelWorkbook.Save; end; i understand this problem happens because the OLE object was created from another thread (absolutely). how can i get around this problem? most likely i'll need to "re-marshall" for this call somehow... any ideas? thank you!

  Read the article

• WCF: Using Streaming and Username/Password authentication at the same time

  - by Kay

  Hi, I have a WCF Service with the following requirements: a) The client requests a file from the server which is transferred as a Stream. Files may be 100MB or larger. I need streaming or chucking or whatever to make sure that IIS is not loading the whole package into memory before starting to send it. b) The client will transfer an ID to identify the file to be downloaded. The user should be authenticated by providing username/password. c) While the username/password part of the communication needs to be encrypted, encryption of the downloaded file is optional for our use case. My other services, where I am returning smaller files, I am using the following binding: <ws2007HttpBinding> <binding name="ws2007HttpExtern" maxReceivedMessageSize="65536000"> <security mode="Message"> <message clientCredentialType="UserName" /> </security> </binding> </ws2007HttpBinding> But, as I said, that is no good for streaming (Message encryption needs the complete message to encrypt and that is not the case when streaming). So, I asked Microsoft support and I got more or less the following proposal: <bindings> <basicHttpBinding> <binding name="basicStreaming" messageEncoding="Mtom" transferMode="StreamedResponse"> <security mode="Transport"> <transport clientCredentialType="Basic" /> </security> </binding> </bindings> <services> <service behaviorConfiguration="MyProject.WCFInterface.DownloadBehavior" name="MyProject.WCFInterface.DownloadFile"> <endpoint address="" binding="basicHttpBinding" bindingConfiguration="basicStreaming" contract="MyProject.WCFInterface.IDownloadFile" /> <endpoint address="mex" binding="mexHttpBinding" contract="IMetadataExchange" /> </service> </services> <behaviors> <serviceBehaviors> <behavior name="MyProject.WCFInterface.DownloadBehavior"> <serviceMetadata httpGetEnabled="false" httpsGetEnabled="true" /> <serviceDebug includeExceptionDetailInFaults="true" /> </behavior> </serviceBehaviors> </behaviors> When I use this, I get the following error message: Could not find a base address that matches scheme https for the endpoint with binding BasicHttpBinding. Registered base address schemes are [http]. I am using the Web Development Server so far (for production IIS7). I have two questions. a) How would you configure WCF to achieve the goal? b) If the MS proposal is good: What I am doing wrong, the error message does not really help me. Thanks.

  Read the article

• Tips / techniques for high-performance C# server sockets

  - by McKenzieG1

  I have a .NET 2.0 server that seems to be running into scaling problems, probably due to poor design of the socket-handling code, and I am looking for guidance on how I might redesign it to improve performance. Usage scenario: 50 - 150 clients, high rate (up to 100s / second) of small messages (10s of bytes each) to / from each client. Client connections are long-lived - typically hours. (The server is part of a trading system. The client messages are aggregated into groups to send to an exchange over a smaller number of 'outbound' socket connections, and acknowledgment messages are sent back to the clients as each group is processed by the exchange.) OS is Windows Server 2003, hardware is 2 x 4-core X5355. Current client socket design: A TcpListener spawns a thread to read each client socket as clients connect. The threads block on Socket.Receive, parsing incoming messages and inserting them into a set of queues for processing by the core server logic. Acknowledgment messages are sent back out over the client sockets using async Socket.BeginSend calls from the threads that talk to the exchange side. Observed problems: As the client count has grown (now 60-70), we have started to see intermittent delays of up to 100s of milliseconds while sending and receiving data to/from the clients. (We log timestamps for each acknowledgment message, and we can see occasional long gaps in the timestamp sequence for bunches of acks from the same group that normally go out in a few ms total.) Overall system CPU usage is low (< 10%), there is plenty of free RAM, and the core logic and the outbound (exchange-facing) side are performing fine, so the problem seems to be isolated to the client-facing socket code. There is ample network bandwidth between the server and clients (gigabit LAN), and we have ruled out network or hardware-layer problems. Any suggestions or pointers to useful resources would be greatly appreciated. If anyone has any diagnostic or debugging tips for figuring out exactly what is going wrong, those would be great as well. Note: I have the MSDN Magazine article Winsock: Get Closer to the Wire with High-Performance Sockets in .NET, and I have glanced at the Kodart "XF.Server" component - it looks sketchy at best.

  Read the article

• Can't Deploy or Upload Large SSRS 2008 Report from VS or IE

  - by Bratch

  So far in this project I have two reports in VS2008/BIDS. The first one contains 1 tablix and is about 100k. The second one contains 3 tablixes (tablices?) and is about 257k. I can successfully deploy the smaller report from VS and I can upload it from the Report Manager in IE. I can view/run it from Report Manager and I can get to the Report Server (web service) URL from my browser just fine. Everything is done over HTTPS and there is nothing wrong with the certificates. With the larger report, the error I get in VS is "The operation has timed out" after about 100 seconds. The error when I upload from IE is "The underlying connection was closed: An unexpected error occurred on a send" after about 130 seconds. In the RSReportServer.config file I tried changing Authentication/EnableAuthPersistence from true to false and restarting the service, but still get the error. I have the key "SecureConnectionLevel" set to 2. Changing this to 0 and turning off SSL is not going to be an option. I added a registry key named "MaxRequestBytes" to HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\HTTP\Parameters and set it to 5242880 (5MB) and restarted the HTTP and SRS services as suggested in a forum post by Jin Chen of MSFT. I still cannot upload the larger report. This is on MS SQL 2008 and WS 2003. Below is part of a log file entry from ...\Reporting Services\LogFiles when I attempted to upload from IE. library!WindowsService_0!89c!02/10/2010-07:57:57:: i INFO: Call to CleanBatch() ends ui!ReportManager_0-1!438!02/10/2010-07:59:33:: e ERROR: The underlying connection was closed: An unexpected error occurred on a send. ui!ReportManager_0-1!438!02/10/2010-07:59:34:: e ERROR: HTTP status code -- 500 -------Details-------- System.Net.WebException: The underlying connection was closed: An unexpected error occurred on a send. --- System.IO.IOException: Unable to write data to the transport connection: An established connection was aborted by the software in your host machine. --- System.Net.Sockets.SocketException: An established connection was aborted by the software in your host machine at System.Net.Sockets.Socket.MultipleSend(BufferOffsetSize[] buffers, SocketFlags socketFlags) at System.Net.Sockets.NetworkStream.MultipleWrite(BufferOffsetSize[] buffers) --- End of inner exception stack trace --- ...

  Read the article

• Impersonation - Access is denied

  - by krisg

  I am having trouble using impersonation to delete a PerformanceCounterCategory from an MVC website. I have a static class and when the application starts it checks whether or not a PerformanceCounterCategory exists, and if it contains the correct counters. If not, it deletes the category and creates it again with the required counters. It works fine when running under the built in webserver Cassini, but when i try run it through IIS7 (Vista) i get the following error: Access is denied Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.ComponentModel.Win32Exception: Access is denied The code used is from an MS article, from memory... var username = "user"; var password = "password"; var domain = "tempuri.org"; WindowsImpersonationContext impersonationContext; // if impersonation fails - return if (!ImpersonateValidUser(username, password, domain, out impersonationContext)) { throw new AuthenticationException("Impersonation failed"); } PerformanceCounterCategory.Delete(PerfCategory); UndoImpersonation(impersonationContext); ... private static bool ImpersonateValidUser(string username, string password, string domain, out WindowsImpersonationContext impersonationContext) { const int LOGON32_LOGON_INTERACTIVE = 2; const int LOGON32_PROVIDER_DEFAULT = 0; WindowsIdentity tempWindowsIdentity; var token = IntPtr.Zero; var tokenDuplicate = IntPtr.Zero; if (RevertToSelf()) { if (LogonUserA(username, domain, password, LOGON32_LOGON_INTERACTIVE, LOGON32_PROVIDER_DEFAULT, ref token) != 0) { if (DuplicateToken(token, 2, ref tokenDuplicate) != 0) { tempWindowsIdentity = new WindowsIdentity(tokenDuplicate); impersonationContext = tempWindowsIdentity.Impersonate(); if (impersonationContext != null) { CloseHandle(token); CloseHandle(tokenDuplicate); return true; } } } } if (token != IntPtr.Zero) CloseHandle(token); if (tokenDuplicate != IntPtr.Zero) CloseHandle(tokenDuplicate); impersonationContext = null; return false; } [DllImport("advapi32.dll")] public static extern int LogonUserA(String lpszUserName, String lpszDomain, String lpszPassword, int dwLogonType, int dwLogonProvider, ref IntPtr phToken); [DllImport("advapi32.dll", CharSet = CharSet.Auto, SetLastError = true)] public static extern int DuplicateToken(IntPtr hToken, int impersonationLevel, ref IntPtr hNewToken); [DllImport("advapi32.dll", CharSet = CharSet.Auto, SetLastError = true)] public static extern bool RevertToSelf(); [DllImport("kernel32.dll", CharSet = CharSet.Auto)] public static extern bool CloseHandle(IntPtr handle); The error is thrown when processing tries to execute the PerformanceCounterCategory.Delete command. Suggestions?

  Read the article

• .Net Intermittent System.Web.Services.Protocols.SoapHeaderException

  - by ScottE

  We have a .net 3.5 web app that consumes third party web services. The proxy was created by adding a web reference to their wsdl. This proxy is not compiled. Our error logging is picking up frequent but intermittent exceptions: An exception of type 'System.Web.Services.Protocols.SoapHeaderException' occurred and was caught If I follow the url to the page that generated the exception, I can't recreate it. Edit: Here is most of the exception - where it bubbled up from Message : Internal Error Type : System.Web.Services.Protocols.SoapHeaderException, System.Web.Services, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a Source : System.Web.Services Help link : Actor : Code : http://schemas.xmlsoap.org/soap/envelope/:Client Detail : Lang : Node : Role : SubCode : Data : System.Collections.ListDictionaryInternal TargetSite : System.Object[] ReadResponse(System.Web.Services.Protocols.SoapClientMessage, System.Net.WebResponse, System.IO.Stream, Boolean) Stack Trace : at System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) at System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) at Vendor.getSearch(getSearchRequest getSearchRequest) in c:\WINDOWS\Microsoft.NET\Framework\v2.0.50727\Temporary ASP.NET Files\root\be43c34e\b09edc7e\App_WebReferences.pww-cf-q.0.cs:line 73 Edit 2: Inner exceptions: I sometimes get the following inner exceptions logged: Message : Unable to read data from the transport connection: An existing connection was forcibly closed by the remote host. Type : System.IO.IOException, mscorlib, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089 Source : System Help link : Data : System.Collections.ListDictionaryInternal TargetSite : Int32 Read(Byte[], Int32, Int32) Stack Trace : at System.Net.Sockets.NetworkStream.Read(Byte[] buffer, Int32 offset, Int32 size) at System.Net.FixedSizeReader.ReadPacket(Byte[] buffer, Int32 offset, Int32 count) at System.Net.Security.SslState.StartReceiveBlob(Byte[] buffer, AsyncProtocolRequest asyncRequest) at System.Net.Security.SslState.CheckCompletionBeforeNextReceive(ProtocolToken message, AsyncProtocolRequest asyncRequest) at System.Net.Security.SslState.StartSendBlob(Byte[] incoming, Int32 count, AsyncProtocolRequest asyncRequest) at System.Net.Security.SslState.ForceAuthentication(Boolean receiveFirst, Byte[] buffer, AsyncProtocolRequest asyncRequest) at System.Net.Security.SslState.ProcessAuthentication(LazyAsyncResult lazyResult) at System.Net.TlsStream.CallProcessAuthentication(Object state) at System.Threading.ExecutionContext.runTryCode(Object userData) at System.Runtime.CompilerServices.RuntimeHelpers.ExecuteCodeWithGuaranteedCleanup(TryCode code, CleanupCode backoutCode, Object userData) at System.Threading.ExecutionContext.RunInternal(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Net.TlsStream.ProcessAuthentication(LazyAsyncResult result) at System.Net.TlsStream.Write(Byte[] buffer, Int32 offset, Int32 size) at System.Net.PooledStream.Write(Byte[] buffer, Int32 offset, Int32 size) at System.Net.ConnectStream.WriteHeaders(Boolean async) And/Or: Message : An existing connection was forcibly closed by the remote host Type : System.Net.Sockets.SocketException, System, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089 Source : System Help link : ErrorCode : 10054 SocketErrorCode : ConnectionReset NativeErrorCode : 10054 Data : System.Collections.ListDictionaryInternal TargetSite : Int32 Receive(Byte[], Int32, Int32, System.Net.Sockets.SocketFlags) Stack Trace : at System.Net.Sockets.Socket.Receive(Byte[] buffer, Int32 offset, Int32 size, SocketFlags socketFlags) at System.Net.Sockets.NetworkStream.Read(Byte[] buffer, Int32 offset, Int32 size) Update We're still working on it. Originally there was a route issue, which was resolved. We're still getting the inner exception with socket errors. We had MS support involved today, and they looked at some traces and network captures. The web service host does round-robin DNS, and they may be responding on a different IP address for the syn syn/ack from one ip, and the next from a different ip. This is not good. This is likely quite specific to our situation, but perhaps it applies to others as well. Microsoft Network Monitor and an application trace got us the information we needed.

  Read the article

• MinGW/G++/g95 link problem - libf95 undefined reference to `MAIN_'

  - by pivakaka

  Hi folks, Summing up, my problem consists on compiling g95 objects inside a C++ application. Actually, I'm constructing an interface for an old fortran program. For this task, I'm using the wxWidgets GUI library, and calling fortran subroutines when necessary. At the beginning, I was developing the entire project compiling my fortran files with gfortran (which comes with GCC) and linking them with my app by the g++ -o... command. Everything was working fine but some numbers values calculated by my fotran subroutines returned NAN values. Doing some research, I realized that compiling my fortran files with gfortran with the -m32 flag, generates this NAN values problem. Although compiling with -m64 flag, my code works properly well. The only trouble here is that my App should be 32bits and then I tryed another compiller. Here I found g95 Fortran compiler, which compiles my fortran code and gives the right output on a 32bits environment. But when I'm trying to link these g95 objects into my program I see this following error: g++ -oCyclonTechTower.exe src\fortran\Modulo_Global.o src\fortran\Prop_Fisicas.o src\fortran\inversa.o src\fortran\tower.o src\fortran\PredadeCarga.o src\fortran\gota.o src\fortran\tadi.o src\view\SimulationORSATCustomDialog.o src\view\SimulationChildGUIFrame.o src\view\ParentGUIFrame.o src\view\ClientGUIFrame.o src\model\TowerData.o src\controller\SimulationController.o src\THEIACyclonTechTower.o ..\Resource\resource.o -Lc:\wxWidgets-2.6.4\lib -Lc:\MinGW\lib\gcc-lib\i686-pc-mingw32\4.1.2 -Bdynamic -Wl,--subsystem,windows -mwindows c:\wxWidgets-2.6.4\lib\libwx_mswu-2.6.a -lwxregexu-2.6 -lwxexpat-2.6 -lwxtiff-2.6 -lwxjpeg-2.6 -lwxpng-2.6 -lwxzlib-2.6 -lrpcrt4 -loleaut32 -lole32 -luuid -lwinspool -lwinmm -lshell32 -lcomctl32 -lcomdlg32 -lctl3d32 -ladvapi32 -lwsock32 -lgdi32 -lgcc -lf95 c:\MinGW\lib\gcc-lib\i686-pc-mingw32\4.1.2/libf95.a(main.o):(.text+0x32): undefined reference to `MAIN_' collect2: ld returned 1 exit status Build error occurred, build is stopped Time consumed: 1531 ms. I have already read the g95 Manual for integration with C++ and I'm actually calling these functions bellow for controlling the fortran environment: void g95_runtime_start(int argc, char *argv[]); void g95_runtime_stop(); I also included the g95 Fortran Runtime Library libf95.a and the libgcc.a into my linker command. Finishing, I don't have a main method implemented because this is managed by wxWidgets, and my fortran subroutines can not have a main function because this is a C++ program calling fortran functions. Can some of you guys help me with this problem? How can I fix this undefined reference to MAIN__ problem? Any idea will be much appreciated. Thanks in advance, George

  Read the article

• WCF ReliableSession and Timeouts

  - by user80108

  I have a WCF service used mainly for managing documents in a repository. I used the chunking channel sample from MS so that I could upload/download huge files. Now I implemented reliable session with the service and I am seeing some strange behaviors. Here are the timeout values I am using. this.SendTimeout = new TimeSpan(0,10,0); this.OpenTimeout = new TimeSpan(0, 1, 0); this.CloseTimeout = new TimeSpan(0, 1, 0); this.ReceiveTimeout = new TimeSpan(0,10, 0); reliableBe.InactivityTimeout = new TimeSpan(0,2,0); I have the following issues. 1. If the Service is not up & running, the clients are not get disconnected after OpenTimeout. I tried it with my test client. Scenario 1: Without Reliable Session: I get the following exception: Could not connect to net.tcp://localhost:8788/MediaManagementService/ep1. The connection attempt lasted for a time span of 00:00:00.9848790. TCP error code 10061: No connection could be made because the target machine actively refused it 127.0.0.1:8788 This is the correct behavior as I have given the OpenTimeout as 1 sec. Scenario 2: With ReliableSession: I get the same exception: Could not connect to net.tcp://localhost:8788/MediaManagementService/ep1. The connection attempt lasted for a time span of 00:00:00.9692460. TCP error code 10061: No connection could be made because the target machine actively refused it 127.0.0.1:8788. But this message comes after around 10 mintes . (I believe after SendTimeout) So here I just have enabled the reliable session and now it looks like the OpenTimeout = SendTimeout for the client. Is this desired behavior? 2: Issue while uploading huge files with ReliableSession: The general rule is that you have to set a huge value for the maxReceivedMessageSize, SendTimeout and ReceiveTimeout. But in the case of Chunking channel, the max received message size doesn't matter as the data is sent in chunks. So I set a huge value for Send and ReceiveTimeout : say 10 hours. Now the upload is going fine, but it has a side effect that, even if the Service is not up, it takes 10 hours to timeout the client connection due to the behavior mentioned in (1). Please let me know your thoughts on this behavior.

  Read the article

• NoPrimaryKeyException from DBUnit when loading a dataset into a databse

  - by Omar Kooheji

  I'm getting NoPrimaryKeyException when I try to run one of my unit tests which uses DBUnit. The datatable is created using Hibernate and is a join table between two classes mapping a many to many relationship. The annotations that define the relationship are as follows: @Override @ManyToMany @JoinTable(name="offset_file_offset_entries", joinColumns={@JoinColumn(name="offset_entry_id")},inverseJoinColumns={@JoinColumn(name="file_description_id")}) public List<OffsetEntry> getOffsets() { The other entries in in the XML file I'm using to define the dataset seem to work fine but not the join table. I get the following exception: org.dbunit.dataset.NoPrimaryKeyException: offset_file_offset_entries at org.dbunit.operation.UpdateOperation.getOperationData(UpdateOperation.java:72) at org.dbunit.operation.RefreshOperation$UpdateRowOperation.<init>(RefreshOperation.java:266) at org.dbunit.operation.RefreshOperation.createUpdateOperation(RefreshOperation.java:142) at org.dbunit.operation.RefreshOperation.execute(RefreshOperation.java:100) at org.dbunit.ext.mssql.InsertIdentityOperation.execute(InsertIdentityOperation.java:217) at uk.co.sabio.obscheduler.application.dao.AbstractBaseDatabaseTest.setUp(AbstractBaseDatabaseTest.java:57) at org.springframework.test.context.junit38.AbstractJUnit38SpringContextTests.runManaged(AbstractJUnit38SpringContextTests.java:332) at org.springframework.test.context.junit38.AbstractJUnit38SpringContextTests.access$0(AbstractJUnit38SpringContextTests.java:326) at org.springframework.test.context.junit38.AbstractJUnit38SpringContextTests$1.run(AbstractJUnit38SpringContextTests.java:216) at org.springframework.test.context.junit38.AbstractJUnit38SpringContextTests.runTest(AbstractJUnit38SpringContextTests.java:296) at org.springframework.test.context.junit38.AbstractJUnit38SpringContextTests.runTestTimed(AbstractJUnit38SpringContextTests.java:253) at org.springframework.test.context.junit38.AbstractJUnit38SpringContextTests.runBare(AbstractJUnit38SpringContextTests.java:213) at junit.framework.TestResult$1.protect(TestResult.java:110) at junit.framework.TestResult.runProtected(TestResult.java:128) at junit.framework.TestResult.run(TestResult.java:113) at junit.framework.TestCase.run(TestCase.java:124) at junit.framework.TestSuite.runTest(TestSuite.java:232) at junit.framework.TestSuite.run(TestSuite.java:227) at org.junit.internal.runners.JUnit38ClassRunner.run(JUnit38ClassRunner.java:83) at org.eclipse.jdt.internal.junit4.runner.JUnit4TestReference.run(JUnit4TestReference.java:46) at org.eclipse.jdt.internal.junit.runner.TestExecution.run(TestExecution.java:38) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:467) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:683) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.run(RemoteTestRunner.java:390) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.main(RemoteTestRunner.java:197) the Dataset entry in question looks like this: <offset_file_offset_entries offset_entry_id="1" file_description_id="1" /> And matches up with the database which has both fields as primary keys (The Databse is MS SQL Server if that helps) There are corresponding entries in the two tables being Joined defined in the following xml: <dataset> <file_description file_path="src/test/resources/" file_pattern=".txt" file_description_id="1"/> <offset_file_description file_description_id="1"/> <offset_entries offset_entry_id="1" field_name="Field1" field_length="10" start_index="0"/> <offset_file_offset_entries offset_entry_id="1" file_description_id="1" /> </dataset> Do I have to define the primary keys in the hibernate annotations? If so How do I do so? do I have to change the way I define my dataset to imply that the two columns are a joint primary key? I'm not very proficient with hibernate or DBUnit for that matter and I'm at my wits end so any assistance would be really appreciated.

  Read the article

• ZPL II Extended Characters

  - by Mauro

  I'm trying to print extended code page 850 characters using ZPL II to a Zebra S4M. Whenever one of the extended characters I.E. ASCII value 127 is used I get a box of varying shades of grey instead of the actual value. I'm trying to print ± and ° (ALT+0177 and ALT+0176). I suspect its the RawPrinterHelper I am trying to use (as downloaded from MS, and another from CodeProject) however I cant see where the character codes are going wrong. Weirdly, printing direct from Notepad renders the correct characters, which leads me to believe it is a problem with the raw printer helper class. I am not tied to using the Raw Printer Helper class so if there is a better way of doing it, I am more than happy to see them. SAMPLE ZPLII Without escaped chars ^XA ^FO30,200^AD^FH,18,10^FD35 ± 2 ° ^FS ^FS ^XZ With escaped chars (tried both upper and lower case) ^XA ^FO30,200^AD^FH,18,10^FD35 _b0 2 _b1 ^FS ^FS ^XZ Raw Printer Helper [StructLayout(LayoutKind.Sequential)] public struct DOCINFO { [MarshalAs(UnmanagedType.LPWStr)] public string printerDocumentName; [MarshalAs(UnmanagedType.LPWStr)] public string pOutputFile; [MarshalAs(UnmanagedType.LPWStr)] public string printerDocumentDataType; } public class RawPrinter { [ DllImport("winspool.drv", CharSet = CharSet.Unicode, ExactSpelling = false, CallingConvention = CallingConvention.StdCall)] public static extern long OpenPrinter(string pPrinterName, ref IntPtr phPrinter, int pDefault); [ DllImport("winspool.drv", CharSet = CharSet.Unicode, ExactSpelling = false, CallingConvention = CallingConvention.StdCall)] public static extern long StartDocPrinter(IntPtr hPrinter, int Level, ref DOCINFO pDocInfo); [ DllImport("winspool.drv", CharSet = CharSet.Unicode, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)] public static extern long StartPagePrinter(IntPtr hPrinter); [ DllImport("winspool.drv", CharSet = CharSet.Ansi, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)] public static extern long WritePrinter(IntPtr hPrinter, string data, int buf, ref int pcWritten); [ DllImport("winspool.drv", CharSet = CharSet.Unicode, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)] public static extern long EndPagePrinter(IntPtr hPrinter); [ DllImport("winspool.drv", CharSet = CharSet.Unicode, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)] public static extern long EndDocPrinter(IntPtr hPrinter); [ DllImport("winspool.drv", CharSet = CharSet.Unicode, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)] public static extern long ClosePrinter(IntPtr hPrinter); public static void SendToPrinter(string printerJobName, string rawStringToSendToThePrinter, string printerNameAsDescribedByPrintManager) { IntPtr handleForTheOpenPrinter = new IntPtr(); DOCINFO documentInformation = new DOCINFO(); int printerBytesWritten = 0; documentInformation.printerDocumentName = printerJobName; documentInformation.printerDocumentDataType = "RAW"; OpenPrinter(printerNameAsDescribedByPrintManager, ref handleForTheOpenPrinter, 0); StartDocPrinter(handleForTheOpenPrinter, 1, ref documentInformation); StartPagePrinter(handleForTheOpenPrinter); WritePrinter(handleForTheOpenPrinter, rawStringToSendToThePrinter, rawStringToSendToThePrinter.Length, ref printerBytesWritten); EndPagePrinter(handleForTheOpenPrinter); EndDocPrinter(handleForTheOpenPrinter); ClosePrinter(handleForTheOpenPrinter); } }

  Read the article

• MSSQL: How to copy a file (pdf, doc, txt...) stored in a varbinary(max) field to a file in a CLR sto

  - by user193655

  I ask this question as a followup of this question. A solution that uses bcp and xp_cmdshell, that is not my desired solution, has been posted here: stackoverflow.com/questions/828749/ms-sql-server-2005-write-varbinary-to-file-system (sorry i cannot post a second hyperlink since my reputation is les than 10). I am new to c# (since I am a Delphi developer) anyway I was able to create a simple CLR stored procedures by following a tutorial. My task is to move a file from the client file system to the server file system (the server can be accessed using remote IP, so I cannot use a shared folder as destination, this is why I need a CLR stored procedure). So I plan to: 1) store from Delphi the file in a varbinary(max) column of a temporary table 2) call the CLR stored procedure to create a file at the desired path using the data contained in the varbinary(max) field Imagine I need to move C:\MyFile.pdf to Z:\MyFile.pdf, where C: is a harddrive on local system and Z: is an harddrive on the server. I provide the code below (not working) that someone can modify to make it work? Here I suppose to have a table called MyTable with two fields: ID (int) and DATA (varbinary(max)). Please note it doesn't make a difference if the table is a real temporary table or just a table where I temporarly store the data. I would appreciate if some exception handling code is there (so that I can manage an "impossible to save file" exception). I would like to be able to write a new file or overwrite the file if already existing. [Microsoft.SqlServer.Server.SqlProcedure] public static void VarbinaryToFile(int TableId) { using (SqlConnection connection = new SqlConnection("context connection=true")) { connection.Open(); SqlCommand command = new SqlCommand("select data from mytable where ID = @TableId", connection); command.Parameters.AddWithValue("@TableId", TableId); // This was the sample code I found to run a query //SqlContext.Pipe.ExecuteAndSend(command); // instead I need something like this (THIS IS META_SYNTAX!!!): SqlContext.Pipe.ResultAsStream.SaveToFile('z:\MyFile.pdf'); } } (one subquestion is: is this approach coorect or there is a way to directly pass the data to the CLR stored procedure so I don't need to use a temp table?) If the subquestion's answer is No, could you describe the approach of avoiding a temp table? So is there a better way then the one I describe above (=temp table + Stored procedure)? A way to directly pass the dataastream from the client application to the CLR stored procedure? (my files can be any size but also very big)

  Read the article

< Previous Page | 274 275 276 277 278 279 280 281 282 283 284 285  | Next Page >