Search Results

Search found 10939 results on 438 pages for 'third monitor'.

Page 29/438 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

• Brand New MOnitor Won't Get Input From CPU

  - by HollerTrain

  I have an old Dell 2350. I found a HD a few months ago and plugged it in and it booted up. So I just purchased a monitor and plugged it in, and put the HD inside and connected the two connections (Bus, and a four pronged connector) and no signal is being sent to monitor. is this a monitor issue or the HD is just dead? HD is spinning. CPU is turned on :) Yet no signal.. any thoughts?

  Read the article

• 2 GPUs (for multi-monitor setup)

  - by A Dwarf

  I have a machine to which I need to connect a second monitor. This machine currently hosts a ATI Radeon HD 4770 with two DVI adapters. The second monitor to be hooked to this machine is a VGA monitor. Until I find a DVI-VGA adpater, I'm thinking installing a second graphics card which does have a VGA adapter, an NVidia card. Can I successfully run both AMD and NVidia cards on this machine? Any specifics I must be aware of, like how to ensure the ATI card to be the main card? Operating system is Windows 7

  Read the article

• Lenovo t400 laptop docking station with DVI out shows green artifacts when connected to monitor

  - by Roy Rico

  I have a Lenovo T400 laptop, with Windows XP. I have a docking station connected via DVI to my Samnsung monitor. I'm connected at 1920x1200 resolution and I keep seeing all these green dots (when colors are supposed to be near black). It's really bad. I have tried running on my Samsung monitor, at all sizes, even down town 1280x1024 like my monitors at work. When I use the docking station at work, I am able to connect 2 1280x1024 NEC monitors (one via DVI, one through VGA, both through my docking station). I have absolutely no issue there, both displays work great. I have tried to update the drivers, I've even installed the latest video drivers from lenovo's site (DEC-02-2010). Is anyone familiar with this issue? Details: Docking Station: Lenovo Advanced Mini Dock- 250410U - NIB Montior at home: Samsung T240 24-inch monitor Monitors at work: NEC monitors

  Read the article

• Brand New Monitor Won't Get Input From Computer

  - by HollerTrain

  I have an old Dell 2350. I found a HD a few months ago and plugged it in and it booted up. So I just purchased a monitor and plugged it in, and put the HD inside and connected the two connections (Bus, and a four pronged connector) and no signal is being sent to monitor. is this a monitor issue or the HD is just dead? HD is spinning. CPU is turned on :) Yet no signal.. any thoughts?

  Read the article

• RandR 1.4 Optimus Dual Monitor

  - by mathepic

  So, I have a dual monitor setup. HDMI comes in through Nvidia, main display is through Intel (I think). I want to use XMonad with the dual setup, and I want to be able to run with or without the second monitor. Is this even doable? I'm using RandR 1.4 and can get both monitors to display something at the same time (by messing with xrandr) but XMonad can never detect more than one rectangle form Xinerama. Does anyone have a working multi-monitor xinerama or twinview configuration that works with optimus/randr 1.4?

  Read the article

• Trouble with external monitor under Windows 7 on MacBook Pro Boot Camp

  - by Colm

  I'm running Windows 7 32-bit on a mid-2010 15" MacBook Pro Intel Core i5 under Boot Camp. I've had trouble getting it to work with my second display and searching Google for an appropriate answer has failed me. I'm on the latest version of Boot Camp - 3.2 - and have updated the drivers for the NVIDIA GeForce GT 330M. The monitor is connected via a VGA cable, and is a Dell ST2410. The monitor is recognised by Windows, which knows it's a Dell and its resolution. The desktop should be extended onto the second monitor - however nothing is showing. It remains black, though it doesn't show a lack of signal coming through which I would have expected. Any ideas what's wrong?

  Read the article

• Best way to monitor host

  - by Axle

  I have just set up a host which receives messages from 300b to 1500b (wrapped stx etx)and replies with the same. It works fine but some times it receives junk data. Is there anyway to monitor this out of band data just so we can make sure we are not receiving massive amounts of it. Also is it possible to monitor if connections time out - where the host did not reply in time or long connections where it takes the host 20 seconds to reply when it normally takes 5. I am aware of IP monitor but I don't think it covers enough - Is there anything else or any other way? Thanks in advance!

  Read the article

• Suitable companion monitors for HP LP3065 30" primary monitor

  - by Bittercoder

  I have an HP LP3065 30" monitor - now I want to add a couple of companion screens to either side of it - I've heard to people suggesting 21" monitors in portrait mode - but it seems difficult to find a suitable panel these day, as 22" wide-screen monitors have become common, and I can't seem to find anything with a suitable 1600 pixel width. Can anyone recommend a suitable monitor, and suggest what criteria are best for picking a suitable monitor - what's important to consider - I'm thinking things like: Exact resolution match? Viewing angle? Small/thin bezel?

  Read the article

• Radeon hd 5700 monitor blank until connected HDMI device is started

  - by kaido loor

  Have win7, radeon hd 5700. When both PC monitor and HDMI device (Onkyo 607) are connected to Radeon card, the monitor diplays boot info, "starting windows, etc" but goes blank when "log into windows" should appear. Monitor comes back (w normal screen) if Onkyo and TV are turned on, not before. Multiple monitors is disabled. Really crazy. Any help appreciated. Generally, Onkyo can pick up HDMI signal ok, so at least smth works as intended.

  Read the article

• How to get monitor resolution of 1680x1050 using ATI Radeon HD 2600 PRO in a dual monitor setup

  - by user7651

  I have Sapphire ATI Radeon HD 2600 PRO graphics card in my Windows Server 2008 x64 machine. It has two outputs a VGA and a DVI. I have connected the DVI to my Dell 24" monitor with 1900x1200 resolution and it works 100%. The VGA I have connected to my second monitor a Samsung 22" with native resolution of 1680x1050. But the ATI driver and Catalyst control centre doesn't show this resolution as an option. If I choose a lower resolution like 1280x1024 it looks really bad and fuzzy. I searched in google and downloaded the powerstrip tool that allowed me to create a custom resolution of 1680x1050 and then this option shows up in Catalyst control centre and my 2nd monitor works fine now. But I don't want to pay for an application to choose a display resolution. Why doesn't ATI show me that option by default even though it has no problem in actually supporting the display at resolution. Is there a way to get 1680x1050 resolution using ATI drivers only ?

  Read the article

• Second monitor sometimes will not wake up

  - by peacedog

  My workstation has two monitors and Windows 7 (64bit). Sometimes when I lock my computer and later return and unlock it, the second monitor won't wake up. I have to turn that monitor off and on to get the picture back. They are identical monitors. The "#2" monitor is set as the main display, if that matters. I glanced at the power saving settings but didn't see anything noteworthy, and I'm not sure what I would be looking for (or if that is the right place to look) in the first place. It's not the end of the world but it is annoying. Help?

  Read the article

• My monitor constantly changes from DVI-D to HD15

  - by guest

  I noticed this lately, and it's becoming more often. Basically, when I start my PC, my monitor, which is connected with a DVI-D cable (I don't know what it's called), screen switches to the HD15, where HD15 isn't connected at all. Like, input is changed from DVI-D to HD15, therefore it just blacks out, and then goes back... it's not constant, but it's in random time intervals... I can't do anything on my computer because of this. I even tried connecting it with both DVI-D cable and HD15 cable to the processor, but it still sucks. Is there any way I could force my monitor to stay at only one input method? I'm on XP SP3, and this monitor is about 10 or less years old, a Sony model.

  Read the article

• How to disable monitor auto detection in Windows 7?

  - by Jay Yother

  I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection?

  Read the article

• unable to sniff traffic despite network interface being in monitor or promiscuous mode

  - by user65126

  I'm trying to sniff out my network's wireless traffic but am having issues. I'm able to put the card in monitor mode, but am unable to see any traffic except broadcasts, multicasts and probe/beacon frames. I have two network interfaces on this laptop. One is connected normally to 'linksys' and the other is in monitor mode. The interface in monitor mode is on the right channel. I'm not associated with the access point because, as I understand, I don't need to if using monitor mode (vs promiscuous). When I try to ping the router ip, I'm not seeing that traffic show up in wireshark. Here's my ifconfig settings: daniel@seasonBlack:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:29:9e:b2:89 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8518 (8.5 KB) TX bytes:8518 (8.5 KB) wlan0 Link encap:Ethernet HWaddr 00:21:00:34:f7:f4 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:ff:fe34:f7f4/64 Scope:Link UP BROADCAST RUNNING MTU:1500 Metric:1 RX packets:9758 errors:0 dropped:0 overruns:0 frame:0 TX packets:4869 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3291516 (3.2 MB) TX bytes:677386 (677.3 KB) wlan1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-33-34-00-00-00-00-00-00-00-00 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:1500 Metric:1 RX packets:112754 errors:0 dropped:0 overruns:0 frame:0 TX packets:101 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18569124 (18.5 MB) TX bytes:12874 (12.8 KB) wmaster0 Link encap:UNSPEC HWaddr 00-21-00-34-F7-F4-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Here's my iwconfig settings: daniel@seasonBlack:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:F8:D6:17:34 Bit Rate=54 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=68/70 Signal level=-42 dBm Noise level=-69 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 wmaster1 no wireless extensions. wlan1 IEEE 802.11bg Mode:Monitor Frequency:2.437 GHz Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Here's how I know I'm on the right channel: daniel@seasonBlack:~$ iwlist channel lo no frequency information. eth0 no frequency information. wmaster0 no frequency information. wlan0 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6) wmaster1 no frequency information. wlan1 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6)

  Read the article

• Importing data from third party datasource (open architecture design )

  - by mare

  How would you design an application (classes, interfaces in class library) in .NET when we have a fixed database design on our side and we need to support imports of data from third party data sources, which will most likely be in XML? For instance, let us say we have a Products table in our DB which has columns Id Title Description TaxLevel Price and on the other side we have for instance Products: ProductId ProdTitle Text BasicPrice Quantity. Currently I do it like this: Have the third party XML convert to classes and XSD's and then deserialize its contents into strong typed objects (what we get as a result of this process is classes like ThirdPartyProduct, ThirdPartyClassification, etc.). Then I have methods like this: InsertProduct(ThirdPartyProduct newproduct) I do not use interfaces at the moment but I would like them to. What I would like is implement something like public class Contoso_ProductSynchronization : ProductSynchronization InsertProduct(ContosoProduct p) where ProductSynchronization will be an interface or abstract class. There will most likely be many implementations of ProductSynchronization. I cannot hardcode the types - classes like ContosoProduct, NorthwindProduct might be created from the third party XML's (so preferably I would continue to use deserialization). Hopefully someone will understand what I'm trying to explain here. Just imagine you are the seller and you have numerous providers and each one uses their own proprietary XML format. I don't mind the development, which will of course be needed everytime new format appears, because it will only require 10-20 methods to be implemented, I just want the architecture to be open and support that.

  Read the article

• I'd like my window switcher to be per-monitor. How do I do that?

  - by Erigami

  I have a multi-monitor setup with nVidia drivers, running Unity/Compiz on 12.10. I'd like to treat each monitor separately, so I can switch desktops on one without affecting the other and run a window switcher that only switches between windows on the current monitor. How do I do that? None of the switchers listed in ccsm seem to limit themselves to the currently focused monitor, ditto for desktop switchers.

  Read the article

• Ubuntu Server 12.10 No GUI Headless Boot and/or Reboot

  - by Ubuntu User

  I have a headless server running the latest Ubuntu Server 12.10. It does not have any GUI at all. I am having the same issue that others are having which is that when you boot or reboot without a monitor (headless) the computer does not boot. The solution presented to others was to edit their xorg.conf file. But since I do not want a GUI installed (and therefore chose not to install a GUI after installing Ubuntu 12.10) I do not have a xorg.conf file in the /etc/X11/ directory. Ubuntu is a widely used distro of Linux, especially for server applications, I absolutely love it. Therefore, there has to be someone who solved this already?

  Read the article

• External display suddenly not detected

  - by NChase

  I have a Lenovo IdeaPad U410 running Ubuntu Desktop 13.04. I have an external monitor that I connect to via HDMI, and it's worked flawlessly for six months. I plug in my laptop, it detects the display. The "change display" key built into the laptop works for switching between the two screens. Never any problems. This afternoon, when I reconnected my computer after taking it into another room for a bit, it didn't work. When I open up Display settings, it can't detect the display. I tried disconnecting/reconnecting everything multiple times. And most strangely, that same "change display" key now behaves like a Super key, opening the dash instead of toggling the display. Nothing at all changed between when I plugged it in this morning and when it stopped working a few hours later. I tried xrandr, that doesn't detect it either. Anyone have any ideas?

  Read the article

• Automatically kill a process if it exceeds a given amount of RAM

  - by chrisamiller

  I work on large-scale datasets. When testing new software, a script will sometimes sneak up on me, quickly grab all available RAM, and render my desktop unusable. I'd like a way to set a RAM limit for a process so that if it exceeds that amount, it will be killed automatically. A language-specific solution probably won't work, as I use all sorts of different tools (R, Perl, Python, Bash, etc). So is there some sort of process-monitor that will let me set a threshold amount of RAM and automatically kill a process if it uses more?

  Read the article

• Computer Lab School for Orphans

  - by Brendon

  I am helping out an NGO, called Orphans Found Fund, here in Arusha Tanzania setup a computer lab to teach students about Ubuntu and open source applications. I have installed Ubuntu 10.10 on all the systems. What I'm wondering about is how to tweak the systems so that the kids cannot: Delete or alter system files Alter the system settings Add or remove applications Exceed a time limit (like an Internet Cafe) Also as the administrator I would like to monitor the usage for another system to make sure that abuse of network is not taking place. Any advice is much appreciated. Brendon

  Read the article

• Can't change screen resolution Ubuntu 10.04 (BT)

  - by Universal Coder

  I'm using Backtrack 5 R2 , what is based on Ubuntu 10.04 LTS. It is installed on Samsung Laptop , and default screen resolution in Windows for it is 1366x768 , but BT/Ubuntu Screen Resolution GUI tool (System=Preferences=Monitors) shows that only resolution available is 1024x768 , and called my monitor as "Unknown". Found a solution , that I have to change resolution in /usr/share/xresprobe/xorg.conf , but I did it , logged out/in and restarted many times , but it took me nowhere. Tried with xrandr , but it shows only mentioned 1024x768 as only solution , and when I tried to input needed resolution , but it did not accept it , because it is not available. As much as I googled , there are a lot of people that had similar problems with BT , but most of them solved with VirtualBox additional tools , but it can't help me , because I've installed it as second OS. In one forum read , that same problems is in Ubuntu 12 , so I ask this question here.

  Read the article

• frequency out of range - please change display mode

  - by Dave

  I just downloaded the latest version of the Ubuntu live CD, and have installed it on a desktop computer (a Fujitsu Scaleo P). Once installed it seems to work perfectly, although there are some updates recommended in the Update Manager. My problem is that, after having installed these updates and restarted the computer, I get this message on my monitor, and no Ubuntu interface is visible: frequency out of range - please change display mode I do not know how to change this when I can't access an interface. Is there a command that will bypass trying to boot the GUI and let me change the display mode via a CLI? I am brand new to Ubuntu and any help on this would be much appreciated.

  Read the article

• Switching to an external display, when primary is broken

  - by Shazzner

  I've successfully install Ubuntu 11.10 Desktop (x86) on an old(er) laptop that unfortunately has a broken screen, so there is an external monitor plugged in. On the livecd it come up on the secondary display just fine and I was able to install ubuntu and everything. Unfortunately when I reboot into Ubuntu proper now, the secondary display is off and I'm literally driving blind here trying to switch it to the secondary display. Using Nvidia open source drivers. Things I've tried: Rebooting back into livecd, mounting the partition and trying in vain to find a config file (it uses the open source drivers so no Xorg.conf I could edit manually) Trying to blind-type xrandr settings into what I hope is terminal: xrandr --output VGA1 --auto (nothing happened) Trying to blind install openssh-server so I could ssh into it and maybe configure it from my working computer. For some reason though, no luck. Ubuntu really should default to expanding to all screens for this use case.

  Read the article

• Facing unity problems after upgrading to Ubuntu 12.04

  - by sh2515

  I upgraded to 12.04 and had problems with unity. So this is what I did 1) Ctrl + Alt + F1 sudo apt-get install compizconfig-settings-manager Export DISPLAY=:0 ccsm 2) Ctrl + Alt + F7 3) Enabled unityplugin 4) Ctrl + Alt + F1 unity --replace it worked with a couple of error messages now I have to put in start up application export DISPLAY=:0 unity --replace NVIDIA software recognises my monitor but ubuntu sees it as laptop. something isn't right can someone point out what info I need to put here for people to help. I have been upgrading this from 8 ish so have altered lots especially when compiz fusion first came out. Also if I run recovery session and type 'unity --replace' it starts and runs fine.

  Read the article

• Keep Fullscreen Flash/Silverlight Video opened on Monitor 2

  - by Jonathan Sampson

  Like many of you, I'm working with two monitors. I'm trying to watch an episode on Channel9's vid-cast, but every time I click back onto my other monitor, the video exits fullscreen-mode, and goes back to a tiny box on the page. Is it possible to keep a video in full screen, while working on the second monitor?

  Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >