Search Results

Search found 18209 results on 729 pages for 'loop device'.

Page 295/729 | < Previous Page | 291 292 293 294 295 296 297 298 299 300 301 302  | Next Page >

  • Ethernet cable unplugged after updating from windows 8.0 to 8.1

    - by Pehmolelu
    Yeah, so I went and updated my windows 8 pro to 8.1. Now everything else seems to work but the network. The Ethernet just says that Network cable is unplugged, even though it is plugged and I have tried different cord as well and I have tested that the router works. I have tried uninstalling the network drivers (Realtec PCIe GBE) and reinstall them with no success. After installing drivers the Device Management gives error for it "Device could not be started. Code 10" Before 8.1 update I had rt630x64.inf, after update it was netrt630x64.inf, and after installing the latest driver rt630x64.inf. With rt630x64.inf there isn't any error, but it's still not just working. New downloaded version: 8.020.0815.2013 (From Realtek website) The driver before: 8.1.510.2013 (After updating the windows to 8.1) I'm using Desktop PC, no VM. I dont have VirtualBox or Vmware installed. I have checked from BIOS that the card is enabled. I have booted in safe mode with network enabled. Says unplugged there as well. I have put the power off for few minutes and put back on, no effect. If anyone has any kind of suggestions, please tell.

    Read the article

  • Suggestions for transitioning to new GW/private network

    - by Quinten
    I am replacing a private T1 link with a new firewall device with an ipsec tunnel for a branch office. I am trying to figure out the right way to transition folks at the new site over to the new connection, so that they default to using the much faster tunnel. Existing network: 192.168.254.0/24, gw 192.168.254.253 (Cisco router plugged in to private t1) Test network I have been using with ipsec tunnel: 192.168.1.0/24, gw 192.168.1.1 (pfsense fw plugged in to public internet), also plugged in to same switch as the old network. There are probably ~20-30 network devices in the existing subnet, about 5 with static IPs. The remote endpoint is already the firewall--I can't set up redundant links to the existing subnet. In other words, as soon as I change the tunnel configuration to point to 192.168.254.0/24, all devices in the existing subnet will stop working because they point to the wrong gateway. I'd like some ability to do this slowly--such that I can move over a few clients and verify the stability of the new link before moving critical services or less tolerant users over. What's the right way to do this? Change the netmask on all of the devices to /16, and update gateway to point to the new device? Could this cause any problems? Also, how should I handle DNS? The pfsense box is not aware of my Active Directory environment. But if I change DNS to use the local servers, it will result in a huge slowdown as DNS queries will still be routed over the private t1. I need some help coming up with a plan that's not too disruptive but will really let me thoroughly test the stability of the IPSEC tunnel before I make the final switch. The AD version is 2008R2, as are the servers. Workstations are mostly Windows XP SP3. I have not configured the 192.168.1.0/24 as a site in AD sites and services.

    Read the article

  • How can I determine the IP addresses allocated by DHCP on a router that I'm connected to?

    - by user234831
    This "router" is not a typical situation. I'm using my phone as a hotspot and can only configure a select number of DHCP options. I can manage the limit on how many devices/clients can use my phone as a hotspot. I have to select from a radio-button list with the options: 2,3,4,5, or 8 I can specify the DHCP starting IP address. In this case, it begins at 192.168.6.106 When I'm connected via WIFI to my phone, an ipconfig /all command shows me that the default gateway is 192.168.6.1 and my IPv4 address is 192.168.1.148. I have the luxury of connecting another device to the phone and that device was assigned 192.168.1.121. I've tried connecting to 192.168.6.1, hoping for some sort of router setup page that I'm used to seeing, but there is no such thing or maybe it's just a matter of incompatable operating systems. In summary, the "router" (phone) has an IP address of 192.168.6.1 and a DHCP server that begins at 192.168.6.106 and allows up to 8 connections. Normally, I would assume a range of 192.168.6.106 - 192.168.6.113, but connected clients are showing otherwise. How can I figure out which IP addresses are set aside by DHCP for clients?

    Read the article

  • Cisco ASA 5505 network route for static IP hosts

    - by TheCapn
    I've configured my internal VLAN using the most basic settings where ports 1-7 are assigned from a pool of addresses in the range 192.168.15.5 - 192.168.15.36. These hosts are given access to the internet and it works great. What I'm trying to set up now is allowing users who are connected to the device and specify their IP (say I connect and request 192.168.15.45) are given internet access and can still work alongside DHCP hosts. Those with a DHCP assigned address are blocked from the internet. Mostly the issue resides in that I am very new to working with the device. I feel that the solution is easy but I'm not looking in the right spots and don't have the correct terminology down to google it. Do I need to define access control lists? Group policies? a new VLAN? The rules that are set up seem to be specific to the entire /24 subnet but when I request a static IP outside of the DHCP range I get blocked from other hosts and the internet.

    Read the article

  • iptables, forward traffic for ip not active on the host itself

    - by gucki
    I have kvm guest which's netword card is conntected to the host using a tap device. The tap device is part of a bridge on the host together with eth0 so it can access the public network. So far everything works, the guest can access the public network and it can be accessed from the public network. Now the kvm process on the host provides a vnc server for the guest which listens on 127.0.0.1:5901 on the host. Is there any way to make this vnc server accessible by the ip address which the guest is using (ex. 192.168.0.249), without interrupting the guest from using the same ip (port 5901 is not used by the guest)? It should also work when the guest is not using any ip address at all. So basically I just want to fake IP xx is on the host and only answer/ forward traffic to port 5901 to the host itself. I tried using this NAT rule on the host, but it doesn't work. Ip forwarding is enabled at the host. iptables -t nat -A PREROUTING -p tcp --dst 192.168.0.249 --dport 5901 -j DNAT --to-destination 127.0.0.1:5901 I assume this is because the IP 192.168.0.249 is not not bound to any interfaces and so no ARP requests for it get answered and so no packets for this IP arrive at the host. How can make it work? :)

    Read the article

  • Running Windows 7 physical disk virtualized under Linux

    - by CajunLuke
    I have an existing Windows 7 installation that I'd like to virtualize under Linux. Windows boots fine on Disk A, Linux boots fine on Disk B. (Both disks are SATA.) I can mount the Windows disk when in Linux. I've tried VirtualBox and VMWare Player and neither will allow me to boot from the other disk. VirtualBox doesn't seem to have the option to do so. VMWare Player has the option to have an IDE drive exposed to the virtual environment as a SCSI disk. I've tried that, but it throws the error "Cannot connect virtual device ide1:0 because no corresponding device is available on the host." I've verified that it's pointing to the correct hard drive. I'm willing to try other virtualization products, and I'm not averse to spending a little money to get this to work. I've seen this other question, and it's not a duplicate, as I haven't gotten that far yet. I'm also interested in solutions going the other way (Linux on Windows), but that'd be lagniappe. Gory Hardware Details: Lenovo T410, 2.4 GHz Core i5 (has virtualization extensions), 4GiB RAM, 2x 320 GiB SATA HDD, one in optical bay. Fedora 14 2.6.35.10-74.fc14.x86_64, Windows 7 32-bit.

    Read the article

  • Will the removal of NAT (with the use of IPv6) be bad for consumers? [closed]

    - by Jonathan.
    Possible Duplicate: How will IPv6 impact everyday users? (World IPv6 Day) As I understand when we have finally made the switch to IPv6 not only will NAT be unnecessary but it is incompatible with IPv6? Will that mean that ISPs will have to serve multiple IP addresses per customer? Will they provide a range of addresses for each customer or as each device connects will they get an IP address that isn't necessarily near that of the other devices in their house? But overall will this be bad for the Internet users? as surely it will allow ISPs to see exactly how many devices are being used, and so allow them to charge for the use of additional IP addresses? And then if that happens, what happens when you try to connect an extra device to your network? Will it simply not get an IP address? In my home we have about 15-20 devices connected at once, but for places where there are hundreds of devices, it seems like the perfect opportunity for ISPs to charge more? I think I may have it completely wrong, so is there somewhere where there is an explanation of who things will work when IPv6 becomes the norm?

    Read the article

  • Hard Reset USB in Ubuntu 10.04

    - by Cory
    I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: $ sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: $ sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on serverfault as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

    Read the article

  • Could I have destroyed Partitioning-Scheme/Filesystem of HDDs with External Harddrive Case with builtin Raid-Controller?

    - by th3m3s
    I had just recently bought a Fantec QB-35US3R to have a nice box on my desk to make some backups to. Along with the HDD-Bay I had ordered some 4TB HDDs to let them run in Raid 5, which is handled by the hardware RAID controller of the Fantec HDD-Bay. The QB-35US3R arrived a few days before the hard drives, so I got impatient and had the idea to put three old 1TB disks in the Fantec device, just to test it... Long story short: I made a backup of the most important data on these three disks before they broke. I had set the configuration scheme to RAID 3 at the Fantec device. It seems, that the Fantec RAID controller has "somehow" destroyed the partitioning scheme or the file system, because when put into a HDD docking station, they get recognized by the OS (Ubuntu/Linux) but are not mountable anymore. I tried to recover the data from one HDD via gParted (parted), which ran some hours without success. Here I stopped, before trying other tools, cos I read that the longer a hard drive is running after a the partitioning got destroyed, the worse it gets. What could the HDD-Bay probably have done to my lovely hard drive disks? Is there some routine a RAID controller is executing, when it wants to create a RAID system? Like erasing the partition table (seems not plausible to me.) or writing some information to every hard drive in the RAID (seems more likely to me.)? Is there a chance to recover the data from these HDDs, or is the change a RAID controller makes so significant, that no software is of help?

    Read the article

  • htaccess rewriting all subdomains to subdirectories

    - by indorock
    I'm trying to build a catch-all for any subdomains (not captured by previous rewrite rules) for a certain domain, and serve a website from a subdirectory that resides in the same folder as the .htaccess file. I already have my vhosts.conf to send all unmapped requests to a "playground" folder, where I want to easily create new subdomains by simply adding a subfolder. So, my structure looks like this: /var/www/playground |-> /foo |-> /bar The .htacces living inside the /playground folder and /foo and /bar being seperate websites. I want http://foo.domain.com to point to /foo and http://bar.domain.com to /bar. Here is my .htaccess file: RewriteEngine On RewriteCond %{HTTP_HOST} ^([^.]+).domain.com$ [NC] RewriteCond %{REQUEST_URI} !^/%1/(.*) RewriteRule ^(.*) /%1/$1 [L] This is supposed to capture the subdomain, add it as a subfolder in RewriteRule, then append after the slash and path information. The second RewriteCond is there to prevent an infinite loop. My idea was that %1 in the second RewriteCond would be able to capture the capture group in the first RewriteCond. But so far I haven't had any success, it's always ending up in a redirect loop. If I would replace %1 in the second RewriteCond with hardcoded 'foo' or 'bar', it works, which leads me to believe that you cannot refer to a capture group inside a RewriteCond. Is is true? Or am I missing something?

    Read the article

  • Is it safe to format this partition?

    - by xanesis4
    On a ubuntu server I own, I am running out of space. When I ran sudo parted /dev/sda -l to find all available drives, I got this: Model: ATA ST31000528AS (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 256MB 255MB primary ext2 boot 2 257MB 1000GB 1000GB extended 5 257MB 1000GB 1000GB logical lvm Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-swap_1: 2135MB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 2135MB 2135MB linux-swap(v1) Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-root: 998GB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 998GB 998GB ext4 I understand /dev/mapper/server--vg-root is the filesystem, and /dev/sda1 has some stuff related to GRUB. But, what about /dev/sda2 and /dev/sda5? When I tried to mount /dev/sda2, it said that I needed to specify the file system, which according to the table, is nonexistent. So, is it safe to format this with, say ext4 and mount it? Also, when I tried to mount /dev/sd5, it gave me this error: mount: unknown filesystem type 'LVM2_member' I assume it is NOT save to reformat this. If I'm wrong, then that would be great, because I could save some space. Please let me know either way. Thanks in advance! UPDATE: Here is the result of mount: /dev/mapper/server--vg-root on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/sda1 on /boot type ext2 (rw,acl) /dev/sda1 on /media/hd2 type ext2 (rw)

    Read the article

  • I'm having trouble getting my server to appear online.

    - by JMRboosties
    Total newb question I'm sure. First I had installed WAMP (http://www.wampserver.com), and I was able to access my pages from other computers in my router network, and the virtual device used to debug Android programs (the purpose of my having a server). This functionality failed, however, at some point over these past few days. While my own browser displays the pages just fine, other computers, my Android phone (on our room's wifi), and my virtual device are no longer able to connect to my pages. I had not made any changes in the settings. I uninstalled WAMP and installed EasyPHP. However, the problem was not resolved. I know this is rather vague, but does anyone here have an idea of what may have happened? I forwarded both port 80 (I know its the default HTTP port, I did it just to be safe), and now port 8888 which EasyPHP uses. I turned my firewall on my hosting computer off for good measure. I cannot access my pages from neither remote computers or computers using my router. Any ideas you may have on how to resolve this would be awesome, thanks a lot. And if you need anymore info please tell me.

    Read the article

  • XMLPULLPARSEREXCEPTION...in KSOAP2

    - by aka47
    iam using KSOAP2 for web services. my client is BlackBerry Phone and Server is KeyRingLabs.com. i am using php page for connection...i have taken this code form a Forum.and modified it according to my requirements...but I am having XMLPULLPARSER EXCEPTION...can any body help??? here is my code.... import net.rim.device.api.ui.; import net.rim.device.api.ui.component.; import net.rim.device.api.ui.container.; import net.rim.device.api.system.; import java.util.; import org.ksoap2.; import org.ksoap2.serialization.; import org.ksoap2.transport.; import java.io.IOException; import org.ksoap2.SoapEnvelope; import org.ksoap2.SoapFault; import org.ksoap2.serialization.SoapObject; import org.ksoap2.serialization.SoapSerializationEnvelope; import org.ksoap2.transport.HttpTransport; import org.xmlpull.v1.XmlPullParserException; final class StockQuoteDemo extends UiApplication { public static void main (String[] args) { StockQuoteDemo theApp = new StockQuoteDemo (); theApp.enterEventDispatcher (); } public StockQuoteDemo () { pushScreen (new StockQuoteScreen ()); //doSOAP(); } final class StockQuoteScreen extends MainScreen { public static final String action = "http://keyringlabs.com/Login"; public static final String namespaceRoot = "bbpointofsale.com"; //public static final String webroot = "http://192.168.1.2/bbpointofsale.com/"; public static final String webroot = "http://192.168.0.35/"; //public static final String webroot = "http://www.bbpointofsale.com"; public String errorMessage; public String key; public String transactionID; private HttpTransport transport; private SoapSerializationEnvelope envelope; public StockQuoteScreen () { //transport = new HttpTransport(webroot + "bb/service/index.php"); transport = new HttpTransport(webroot+"Disk/rashid11/index4.php"); transport.debug = true; envelope = new SoapSerializationEnvelope(SoapEnvelope.VER12); key = null; envelope.encodingStyle = SoapSerializationEnvelope.XSD1999; ProcessLogin("[email protected]","123456"); //Dialog.alert("GEN 1"); //Dialog.alert("Warr Gai Vai!!!"); } public boolean onClose () { Dialog.alert ("Goodbye!"); System.exit (0); return true; } public boolean ProcessLogin(String email, String password) { System.err.println("Starting The Process"); errorMessage = ""; String namespace = "urn:" + namespaceRoot + ":login"; //System.err.println("LINK:"+namespace); // SoapObject message = new SoapObject(namespace, "login"); SoapObject message = new SoapObject(namespaceRoot, "login"); message.addProperty("email", email); message.addProperty("password", password); envelope.bodyOut = message; // System.err.println("KSOAP:"+ envelope.toString()); //String soapAction = namespace + "#login"; String soapAction = "http://bbpointofsale.com/login"; // System.err.println("Action : "+soapAction); try { //transport.setXmlVersionTag(""); transport.call(soapAction, envelope); } catch (IOException e) { e.printStackTrace(); System.out.println("error: "+e.getMessage()); errorMessage = e.getMessage(); System.out.println("response1: "+transport.responseDump); return false; } catch (XmlPullParserException e) { e.printStackTrace(); errorMessage = e.getMessage(); System.out.println("request2: "+transport.requestDump); System.out.println("response2: "+transport.responseDump); return false; } try { SoapObject result = (SoapObject) ((SoapObject)envelope.getResponse()).getProperty(0); key = hackToGetResponse("serviceToken", result.toString()); if (key.length() > 0) { System.out.println("KEY:" + key); return true; } else { } } catch (SoapFault e) { errorMessage = e.getMessage(); System.out.println("response3: "+transport.responseDump); return false; } catch (Exception e) { errorMessage = e.getMessage(); System.err.println("response4: "+transport.responseDump); return false; } return false; } public String hackToGetResponse(String key, String response) { System.out.println("hackToGetResponse:" + response); String start = "anyType{key=" + key + "; value="; String end = "; }"; if (response.indexOf(start) == -1 || response.indexOf(end) == -1) return ""; System.out.println("hackToGetResponse:" + "response.substring(0, " + response.indexOf(start) + ").substring(0, " + response.indexOf(end) + ");"); response = response.substring(response.indexOf(start) + start.length()); response = response.substring(0, response.indexOf(end)); if (response.indexOf("anyType{}") != -1) return ""; return response; } } } //******************PHP FILE************************ $server = new SoapServer(null, array('uri' = "urn:keyringlabs.com")); //$server = new SoapServer(null, array('uri' = "urn: bbpointofsale.com")); $server-addFunction("login"); //$email='[email protected]'; //$pass='123456'; function login($email, $pass) { if (strlen($email) == 0) { return Array('serviceToken' => ''); } elseif (strlen($pass) == 0) { return Array('serviceToken' => ''); } else { $objMerchant = Merchant::LoadByEmailPassword($email, $pass); if ($objMerchant == null || $objMerchant->Id &lt==1) { return Array('serviceToken' => ''); } else { $key = uniqid(); $objSess = new Merchantsessions(); $objSess->MerchantID = $objMerchant->Id; $objSess->ServiceToken = $key; $objSess->Save(); } } $result = Array('serviceToken' => $key); //print $result; return $result; } ? ///**************************************** is there any need of an XML page or something..to run it perfectly...please help thank you for your time!

    Read the article

  • Simple Adapter error

    - by Rahul Varma
    Hi, I have the following errors when i try to access the simple adapter from my program... Plz can anyone help me solving the error... Desperate to get it done.... android.widget.SimpleAdapter.getCount(SimpleAdapter.java:95) android.widget.ListView.setAdapter(ListView.java:431) com.stellent.gorinka.MusicListActivity.list(MusicListActivity.java:76) com.stellent.gorinka.MusicListActivity$1.run(MusicListActivity.java:67) android.os.Handler.handleCallback(Handler.java:587) android.os.Handler.dispatchMessage(Handler.java:92) at android.os.Looper.loop(Looper.java:123) android.os.Handler.handleCallback(Handler.java:587) android.os.Handler.dispatchMessage(Handler.java:92) android.os.Looper.loop(Looper.java:123) Here' the code for Adapter... public class SongsAdapter extends SimpleAdapter{ static List<HashMap<String,String>> songsList; Context context; LayoutInflater inflater; public SongsAdapter(Context context,List<HashMap<String,String>> imgListWeb,int layout,String[] from,int[] to,LayoutInflater inflater) { super(context,songsList,layout,from,to); this.songsList=songsList; this.context=context; this.inflater=inflater; // TODO Auto-generated constructor stub }@Override public View getView(int postition,View convertView,ViewGroup parent)throws java.lang.OutOfMemoryError{ try { View v = ((LayoutInflater) inflater).inflate(R.layout.row,null); ImageView images=(ImageView)v.findViewById(R.id.image); TextView tvTitle=(TextView)v.findViewById(R.id.text1); TextView tvAlbum=(TextView)v.findViewById(R.id.text2); TextView tvArtist=(TextView)v.findViewById(R.id.text3); HashMap<String,String> songsHash=songsList.get(postition); String path=songsHash.get("path"); String title=songsHash.get("title"); String album=songsHash.get("album"); String artist=songsHash.get("artist"); String imgPath=path; final ImageView imageView = (ImageView) v.findViewById(R.id.image); AsyncImageLoaderv asyncImageLoader=new AsyncImageLoaderv(); Bitmap cachedImage = asyncImageLoader.loadDrawable(imgPath, new AsyncImageLoaderv.ImageCallback() { public void imageLoaded(Bitmap imageDrawable, String imageUrl) { imageView.setImageBitmap(imageDrawable); } }); imageView.setImageBitmap(cachedImage); tvTitle.setText(title); tvAlbum.setText(album); tvArtist.setText(artist); return v; } catch(Exception e){ Log.e("error",e.toString()); } return null; } And also in my main program the focus is not entering the loop... The implementation in the loop isnt getting executed...Here's the code for it... public void list() { Log.d("#####","#####"); LayoutInflater inflater=getLayoutInflater(); String[] from={}; int[] n={}; adapter=new SongsAdapter(getApplicationContext(),songNodeDet,R.layout.row,from,n,inflater); lv.setAdapter(adapter);} private Handler handler = new Handler() { public void handleMessage(Message msg){ Log.d("*****","handler"); removeDialog(0); p.dismiss(); } }; public void webObjectList(Object[] imgListObj,String logInSess) throws XMLRPCException{ songNodeWeb = new HashMap<?,?>[imgListObj.length]; if(imgListObj!=null){ Log.e("completed","completed"); for(int i=0;i<imgListObj.length;i++){ //imgListObj.length songNodeWeb[i]=(HashMap<?,?>)imgListObj[i]; String nodeid=(String) songNodeWeb[i].get("nid"); Log.e("img",i+"completed"); HashMap<String,String> nData=new HashMap<String,String>(); nData.put("nid",nodeid); Object nodeget=client.call("node.get",logInSess,nodeid); HashMap<?,?> imgNode=(HashMap<?,?>)nodeget; String titleName=(String) imgNode.get("titles"); String movieName=(String) imgNode.get("album"); String singerName=(String) imgNode.get("artist"); nData.put("titles", titleName); nData.put("album", movieName); nData.put("artist", singerName); Object[] imgObject=(Object[])imgNode.get("title_format"); HashMap<?,?>[] imgDetails=new HashMap<?,?>[imgObject.length]; imgDetails[0]=(HashMap<?, ?>)imgObject[0]; String path=(String) imgDetails[0].get("filepath"); if(path.contains(" ")){ path=path.replace(" ", "%20"); } String imgPath="http://www.gorinka.com/"+path; paths.add(imgPath); nData.put("path", imgPath); Log.e("my path",path); String mime=(String)imgDetails[0].get("filemime"); nData.put("mime", mime); SongsList songs=new SongsList(titleName,movieName,singerName,imgPath,imgPath); SngList.add(i,songs); songNodeDet.add(i,nData); } Log.e("paths values",paths.toString()); // return imgNodeDet; handler.sendEmptyMessage(0); } } public void getSongs() throws MalformedURLException, XMLRPCException { String ur="http://www.gorinka.com/?q=services/xmlrpc"; URL u=new URL(ur); client = new XMLRPCClient(u); //Connecting to the website HashMap<?, ?> siteConn =(HashMap<?, ?>) client.call("system.connect"); // Getting initial sessio id String initSess=(String)siteConn.get("sessid"); //Login to the site using session id HashMap<?, ?> logInConn =(HashMap<?, ?>) client.call("user.login",initSess,"prakash","stellentsoft2009"); //Getting Login sessid logInSess=(String)logInConn.get("sessid"); websongListObject =(Object[]) client.call("nodetype.get",logInSess,""); webObjectList(websongListObject,logInSess); Log.d("webObjectList","webObjectList"); runOnUiThread(returnRes); } }

    Read the article

  • rotating bitmaps. In code.

    - by Marco van de Voort
    Is there a faster way to rotate a large bitmap by 90 or 270 degrees than simply doing a nested loop with inverted coordinates? The bitmaps are 8bpp and typically 2048*2400*8bpp Currently I do this by simply copying with argument inversion, roughly (pseudo code: for x = 0 to 2048-1 for y = 0 to 2048-1 dest[x][y]=src[y][x]; (In reality I do it with pointers, for a bit more speed, but that is roughly the same magnitude) GDI is quite slow with large images, and GPU load/store times for textures (GF7 cards) are in the same magnitude as the current CPU time. Any tips, pointers? An in-place algorithm would even be better, but speed is more important than being in-place. Target is Delphi, but it is more an algorithmic question. SSE(2) vectorization no problem, it is a big enough problem for me to code it in assembler Duplicates How do you rotate a two dimensional array?. Follow up to Nils' answer Image 2048x2700 - 2700x2048 Compiler Turbo Explorer 2006 with optimization on. Windows: Power scheme set to "Always on". (important!!!!) Machine: Core2 6600 (2.4 GHz) time with old routine: 32ms (step 1) time with stepsize 8 : 12ms time with stepsize 16 : 10ms time with stepsize 32+ : 9ms Meanwhile I also tested on a Athlon 64 X2 (5200+ iirc), and the speed up there was slightly more than a factor four (80 to 19 ms). The speed up is well worth it, thanks. Maybe that during the summer months I'll torture myself with a SSE(2) version. However I already thought about how to tackle that, and I think I'll run out of SSE2 registers for an straight implementation: for n:=0 to 7 do begin load r0, <source+n*rowsize> shift byte from r0 into r1 shift byte from r0 into r2 .. shift byte from r0 into r8 end; store r1, <target> store r2, <target+1*<rowsize> .. store r8, <target+7*<rowsize> So 8x8 needs 9 registers, but 32-bits SSE only has 8. Anyway that is something for the summer months :-) Note that the pointer thing is something that I do out of instinct, but it could be there is actually something to it, if your dimensions are not hardcoded, the compiler can't turn the mul into a shift. While muls an sich are cheap nowadays, they also generate more register pressure afaik. The code (validated by subtracting result from the "naieve" rotate1 implementation): const stepsize = 32; procedure rotatealign(Source: tbw8image; Target:tbw8image); var stepsx,stepsy,restx,resty : Integer; RowPitchSource, RowPitchTarget : Integer; pSource, pTarget,ps1,ps2 : pchar; x,y,i,j: integer; rpstep : integer; begin RowPitchSource := source.RowPitch; // bytes to jump to next line. Can be negative (includes alignment) RowPitchTarget := target.RowPitch; rpstep:=RowPitchTarget*stepsize; stepsx:=source.ImageWidth div stepsize; stepsy:=source.ImageHeight div stepsize; // check if mod 16=0 here for both dimensions, if so -> SSE2. for y := 0 to stepsy - 1 do begin psource:=source.GetImagePointer(0,y*stepsize); // gets pointer to pixel x,y ptarget:=Target.GetImagePointer(target.imagewidth-(y+1)*stepsize,0); for x := 0 to stepsx - 1 do begin for i := 0 to stepsize - 1 do begin ps1:=@psource[rowpitchsource*i]; // ( 0,i) ps2:=@ptarget[stepsize-1-i]; // (maxx-i,0); for j := 0 to stepsize - 1 do begin ps2[0]:=ps1[j]; inc(ps2,RowPitchTarget); end; end; inc(psource,stepsize); inc(ptarget,rpstep); end; end; // 3 more areas to do, with dimensions // - stepsy*stepsize * restx // right most column of restx width // - stepsx*stepsize * resty // bottom row with resty height // - restx*resty // bottom-right rectangle. restx:=source.ImageWidth mod stepsize; // typically zero because width is // typically 1024 or 2048 resty:=source.Imageheight mod stepsize; if restx>0 then begin // one loop less, since we know this fits in one line of "blocks" psource:=source.GetImagePointer(source.ImageWidth-restx,0); // gets pointer to pixel x,y ptarget:=Target.GetImagePointer(Target.imagewidth-stepsize,Target.imageheight-restx); for y := 0 to stepsy - 1 do begin for i := 0 to stepsize - 1 do begin ps1:=@psource[rowpitchsource*i]; // ( 0,i) ps2:=@ptarget[stepsize-1-i]; // (maxx-i,0); for j := 0 to restx - 1 do begin ps2[0]:=ps1[j]; inc(ps2,RowPitchTarget); end; end; inc(psource,stepsize*RowPitchSource); dec(ptarget,stepsize); end; end; if resty>0 then begin // one loop less, since we know this fits in one line of "blocks" psource:=source.GetImagePointer(0,source.ImageHeight-resty); // gets pointer to pixel x,y ptarget:=Target.GetImagePointer(0,0); for x := 0 to stepsx - 1 do begin for i := 0 to resty- 1 do begin ps1:=@psource[rowpitchsource*i]; // ( 0,i) ps2:=@ptarget[resty-1-i]; // (maxx-i,0); for j := 0 to stepsize - 1 do begin ps2[0]:=ps1[j]; inc(ps2,RowPitchTarget); end; end; inc(psource,stepsize); inc(ptarget,rpstep); end; end; if (resty>0) and (restx>0) then begin // another loop less, since only one block psource:=source.GetImagePointer(source.ImageWidth-restx,source.ImageHeight-resty); // gets pointer to pixel x,y ptarget:=Target.GetImagePointer(0,target.ImageHeight-restx); for i := 0 to resty- 1 do begin ps1:=@psource[rowpitchsource*i]; // ( 0,i) ps2:=@ptarget[resty-1-i]; // (maxx-i,0); for j := 0 to restx - 1 do begin ps2[0]:=ps1[j]; inc(ps2,RowPitchTarget); end; end; end; end;

    Read the article

  • How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

    - by Philip Durbin
    Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError: { PHYRdyChg CommWake } May 5 16:54:40 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:45 fs-2 kernel: ata1: device not ready (errno=-16), forcing hardreset May 5 16:54:45 fs-2 kernel: ata1: soft resetting link May 5 16:54:50 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:55 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:54:55 fs-2 kernel: ata1: soft resetting link May 5 16:55:00 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:05 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:05 fs-2 kernel: ata1: soft resetting link May 5 16:55:10 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:40 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:40 fs-2 kernel: ata1: limiting SATA link speed to 1.5 Gbps May 5 16:55:40 fs-2 kernel: ata1: soft resetting link May 5 16:55:45 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:45 fs-2 kernel: ata1: reset failed, giving up May 5 16:55:45 fs-2 kernel: ata1: EH complete I tried a couple things to make the server find the new /dev/sda, such as rescan-scsi-bus.sh but they didn't work: [root@fs-2 ~]# echo "---" > /sys/class/scsi_host/host0/scan -bash: echo: write error: Invalid argument [root@fs-2 ~]# [root@fs-2 ~]# /root/rescan-scsi-bus.sh -l [snip] 0 new device(s) found. 0 device(s) removed. [root@fs-2 ~]# [root@fs-2 ~]# ls /dev/sda ls: /dev/sda: No such file or directory I ended up rebooting the server. /dev/sda was recognized, I fixed the software RAID, and everything is fine now. But for next time, how can I make Linux recognize a new SATA drive I have hot swapped in without rebooting? The operating system in question is RHEL5.3: [root@fs-2 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) The hard drive is a Seagate Barracuda ES.2 SATA 3.0-Gb/s 500-GB, model ST3500320NS. Here is the lscpi output: [root@fs-2 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) Update: In perhaps a dozen cases, we've been forced to reboot servers because hot swap hasn't "just worked." Thanks for the answers to look more into the SATA controller. I've included the lspci output for the problematic system above (hostname: fs-2). I could still use some help understanding what exactly isn't supported hardware-wise in terms of hot swap for that system. Please let me know what other output besides lspci might be useful. The good news is that hot swap "just worked" today on one of our servers (hostname: www-1), which is very rare for us. Here is the lspci output: [root@www-1 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 09:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)

    Read the article

  • Confirm disk is broken when it passes all diagnostics

    - by Halfgaar
    I have a system with a potentially broken disk, but the disk passes all manner of diagnostics. I have been unable to confirm that the disk is broken. What are my options? I could just replace the disk, but because this situation is very similar to another more severe situation I have (long story), I'd like to actually make a proper diagnosis as opposed to randomly binning hardware. The issue and history is this: I had a Debian Linux PC (500 MHz P3) acting as router, nagios and munin. It crashed every couple of weeks. No logs or dmesg could be obtained (because it's an old Compaq that only boots when you configure it as keyboardless, making connecting a keyboard later, once it's booted, impossible). At the time, I just replaced the computer with another Compaq (P4 2.4 GHz) because I thought the hardware was faulty. However, it still crashed every couple of weeks. the difference is that on this computer, I can still SSH into it. It gives all kinds of errors on hda. I'd like to confirm that the disk is broken, but nothing I do confirms this: SMART error logs shows no errors. Normally when a disk starts acting up, SMART my pass, but it still records a read-error in the error log. SMART self-test (smartctl -t long /dev/sda) completes without errors. re-allocated sector count (a tell-tale parameter) has been 31 all its life, even when the disk was still in use in my desktop PC years ago, and it still is. The figure never changed. dd if=/dev/sda of=/dev/null bs=4096 passes with flying colors. What else can I do to assess the health of the drive? Again, this is not about making this router fully functional again, this is a disk forensic question, because it just so happens that I have another server that potentially has the same problem, and knowing the answer to this will possibly help me greatly. For the record, below are logs and such. This is the smartctl -a output: smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus family Device Model: ST3120026A Serial Number: 5JT1CLQM Firmware Version: 3.06 User Capacity: 120,034,123,776 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 6 ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2 Local Time is: Mon Jul 1 21:18:33 2013 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 24) The self-test routine was aborted by the host. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 050 046 006 Pre-fail Always - 47766662 3 Spin_Up_Time 0x0003 097 096 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 10 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 31 7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 820305 9 Power_On_Hours 0x0032 048 048 000 Old_age Always - 46373 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 605 194 Temperature_Celsius 0x0022 036 065 000 Old_age Always - 36 195 Hardware_ECC_Recovered 0x001a 050 046 000 Old_age Always - 47766662 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 196 000 Old_age Always - 6 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Aborted by host 80% 46361 - # 2 Extended offline Completed without error 00% 46358 - # 3 Short offline Completed without error 00% 12046 - # 4 Extended offline Completed without error 00% 10472 - # 5 Short offline Completed without error 00% 10471 - # 6 Short offline Completed without error 00% 10471 - # 7 Short offline Completed without error 00% 6770 - # 8 Extended offline Aborted by host 90% 5958 - # 9 Extended offline Aborted by host 90% 5951 - #10 Short offline Completed without error 00% 5024 - #11 Extended offline Aborted by host 80% 5024 - #12 Short offline Completed without error 00% 3697 - #13 Short offline Completed without error 00% 237 - #14 Short offline Completed without error 00% 145 - #15 Short offline Completed without error 00% 69 - #16 Extended offline Completed without error 00% 68 - #17 Short offline Completed without error 00% 66 - #18 Short offline Completed without error 00% 49 - #19 Short offline Completed without error 00% 29 - #20 Short offline Completed without error 00% 29 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. And this is the dmesg error when it has crashed (which repeats for a bunch of different sectors): [1755091.211136] sd 0:0:0:0: [sda] Unhandled error code [1755091.211144] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [1755091.211151] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 08 fe ad 38 00 00 08 00 [1755091.211166] end_request: I/O error, dev sda, sector 150908216

    Read the article

  • How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

    - by Philip Durbin
    Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError: { PHYRdyChg CommWake } May 5 16:54:40 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:45 fs-2 kernel: ata1: device not ready (errno=-16), forcing hardreset May 5 16:54:45 fs-2 kernel: ata1: soft resetting link May 5 16:54:50 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:55 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:54:55 fs-2 kernel: ata1: soft resetting link May 5 16:55:00 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:05 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:05 fs-2 kernel: ata1: soft resetting link May 5 16:55:10 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:40 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:40 fs-2 kernel: ata1: limiting SATA link speed to 1.5 Gbps May 5 16:55:40 fs-2 kernel: ata1: soft resetting link May 5 16:55:45 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:45 fs-2 kernel: ata1: reset failed, giving up May 5 16:55:45 fs-2 kernel: ata1: EH complete I tried a couple things to make the server find the new /dev/sda, such as rescan-scsi-bus.sh but they didn't work: [root@fs-2 ~]# echo "---" > /sys/class/scsi_host/host0/scan -bash: echo: write error: Invalid argument [root@fs-2 ~]# [root@fs-2 ~]# /root/rescan-scsi-bus.sh -l [snip] 0 new device(s) found. 0 device(s) removed. [root@fs-2 ~]# [root@fs-2 ~]# ls /dev/sda ls: /dev/sda: No such file or directory I ended up rebooting the server. /dev/sda was recognized, I fixed the software RAID, and everything is fine now. But for next time, how can I make Linux recognize a new SATA drive I have hot swapped in without rebooting? The operating system in question is RHEL5.3: [root@fs-2 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) The hard drive is a Seagate Barracuda ES.2 SATA 3.0-Gb/s 500-GB, model ST3500320NS. Here is the lscpi output: [root@fs-2 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) Update: In perhaps a dozen cases, we've been forced to reboot servers because hot swap hasn't "just worked." Thanks for the answers to look more into the SATA controller. I've included the lspci output for the problematic system above (hostname: fs-2). I could still use some help understanding what exactly isn't supported hardware-wise in terms of hot swap for that system. Please let me know what other output besides lspci might be useful. The good news is that hot swap "just worked" today on one of our servers (hostname: www-1), which is very rare for us. Here is the lspci output: [root@www-1 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 09:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)

    Read the article

  • Ubuntu, No wireless networks found after correctly installed madwifi

    - by Peter
    Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

    Read the article

  • Unable to access intel fake RAID 1 array in Fedora 14 after reboot

    - by Sim
    Hello everyone, 1st I am relatively new to linux (but not to *nix). I have 4 disks assembled in the following intel ahci bios fake raid arrays: 2x320GB RAID1 - used for operating systems md126 2x1TB RAID1 - used for data md125 I have used the raid of size 320GB to install my operating system and the second raid I didn't even select during the installation of Fedora 14. After successful partitioning and installation of Fedora, I tried to make the second array available, it was possible to make it visible in linux with mdadm --assembe --scan , after that I created one maximum size partition and 1 maximum size ext4 filesystem in it. Mounted, and used it. After restart - a few I/O errors during boot regarding md125 + inability to mount the filesystem on it and dropped into repair shell. I commented the filesystem in fstab and it booted. To my surprise, the array was marked as "auto read only": [root@localhost ~]# cat /proc/mdstat Personalities : [raid1] md125 : active (auto-read-only) raid1 sdc[1] sdd[0] 976759808 blocks super external:/md127/0 [2/2] [UU] md127 : inactive sdc[1](S) sdd[0](S) 4514 blocks super external:imsm md126 : active raid1 sda[1] sdb[0] 312566784 blocks super external:/md1/0 [2/2] [UU] md1 : inactive sdb[1](S) sda[0](S) 4514 blocks super external:imsm unused devices: <none> [root@localhost ~]# and the partition in it was not available as device special file in /dev: [root@localhost ~]# ls -l /dev/md125* brw-rw---- 1 root disk 9, 125 Jan 6 15:50 /dev/md125 [root@localhost ~]# But the partition is there according to fdisk: [root@localhost ~]# fdisk -l /dev/md125 Disk /dev/md125: 1000.2 GB, 1000202043392 bytes 19 heads, 10 sectors/track, 10281682 cylinders, total 1953519616 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1b238ea9 Device Boot Start End Blocks Id System /dev/md125p1 2048 1953519615 976758784 83 Linux [root@localhost ~]# I tried to "activate" the array in different ways (I'm not experienced with mdadm and the man page is gigantic so I was only browsing it looking for my answer) but it was impossible - the array would still stay in "auto read only" and the device special file for the partition it will not be in /dev. It was only after I recreated the partition via fdisk that it reappeared in /dev... until next reboot. So, my question is - How do I make the array automatically available after reboot? Here is some additional information: 1st I am able to see the UUID of the array in blkid: [root@localhost ~]# blkid /dev/sdc: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/sdd: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/md126p1: UUID="60C8D9A7C8D97C2A" TYPE="ntfs" /dev/md126p2: UUID="3d1b38a3-b469-4b7c-b016-8abfb26a5d7d" TYPE="ext4" /dev/md126p3: UUID="1Msqqr-AAF8-k0wi-VYnq-uWJU-y0OD-uIFBHL" TYPE="LVM2_member" /dev/mapper/vg00-rootlv: LABEL="_Fedora-14-x86_6" UUID="34cc1cf5-6845-4489-8303-7a90c7663f0a" TYPE="ext4" /dev/mapper/vg00-swaplv: UUID="4644d857-e13b-456c-ac03-6f26299c1046" TYPE="swap" /dev/mapper/vg00-homelv: UUID="82bd58b2-edab-4b4b-aec4-b79595ecd0e3" TYPE="ext4" /dev/mapper/vg00-varlv: UUID="1b001444-5fdd-41b6-a59a-9712ec6def33" TYPE="ext4" /dev/mapper/vg00-tmplv: UUID="bf7d2459-2b35-4a1c-9b81-d4c4f24a9842" TYPE="ext4" /dev/md125: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/sda: TYPE="isw_raid_member" /dev/md125p1: UUID="420adfdd-6c4e-4552-93f0-2608938a4059" TYPE="ext4" [root@localhost ~]# Here is how /etc/mdadm.conf looks like: [root@localhost ~]# cat /etc/mdadm.conf # mdadm.conf written out by anaconda MAILADDR root AUTO +imsm +1.x -all ARRAY /dev/md1 UUID=89f60dee:e46a251f:7475814b:d4cc19a9 ARRAY /dev/md126 UUID=a8775c90:cee66376:5310fc13:63bcba5b ARRAY /dev/md125 UUID=b9a1149f:ae114fc8:a6000d77:354dc42a [root@localhost ~]# here is how /proc/mdstat looks like after I recreate the partition in the array so that it becomes available: [root@localhost ~]# cat /proc/mdstat Personalities : [raid1] md125 : active raid1 sdc[1] sdd[0] 976759808 blocks super external:/md127/0 [2/2] [UU] md127 : inactive sdc[1](S) sdd[0](S) 4514 blocks super external:imsm md126 : active raid1 sda[1] sdb[0] 312566784 blocks super external:/md1/0 [2/2] [UU] md1 : inactive sdb[1](S) sda[0](S) 4514 blocks super external:imsm unused devices: <none> [root@localhost ~]# Detailed output regarding the array in subject: [root@localhost ~]# mdadm --detail /dev/md125 /dev/md125: Container : /dev/md127, member 0 Raid Level : raid1 Array Size : 976759808 (931.51 GiB 1000.20 GB) Used Dev Size : 976759940 (931.51 GiB 1000.20 GB) Raid Devices : 2 Total Devices : 2 Update Time : Fri Jan 7 00:38:00 2011 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 30ebc3c2:b6a64751:4758d05c:fa8ff782 Number Major Minor RaidDevice State 1 8 32 0 active sync /dev/sdc 0 8 48 1 active sync /dev/sdd [root@localhost ~]# and /etc/fstab, with /data commented (the filesystem that is on this array): # # /etc/fstab # Created by anaconda on Thu Jan 6 03:32:40 2011 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # /dev/mapper/vg00-rootlv / ext4 defaults 1 1 UUID=3d1b38a3-b469-4b7c-b016-8abfb26a5d7d /boot ext4 defaults 1 2 #UUID=420adfdd-6c4e-4552-93f0-2608938a4059 /data ext4 defaults 0 1 /dev/mapper/vg00-homelv /home ext4 defaults 1 2 /dev/mapper/vg00-tmplv /tmp ext4 defaults 1 2 /dev/mapper/vg00-varlv /var ext4 defaults 1 2 /dev/mapper/vg00-swaplv swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 [root@localhost ~]# Thanks in advance to everyone that even read this whole issue :-)

    Read the article

  • Wireless internet connection connects but internet does not work (no packets received). Wired does.

    - by Rodney
    When I connect my PC via ethernet cable to my ADSL router it works fine. When I connect via Wireless it connects and the internet will work for a random amount of time and then stop working. It stays connected with a strong signal but no packets are received. My laptop/iphone are right next to it and wireless works fine. If I open the Wireless USB status, it says it is connected to my SSID with full strength (54 mps - I am 3 meteres away from my router) and the activty shows as Packets 594 SENT and 105 RECEIVED (this goes up VERY slowly) I have tried the following: Turned off anitvirus and firewall completely. Tested the wifi signal- I am writing this on my laptop which is next to my PC and also has full wifi strength. Tried a different wireless adapter - I dug out an old PCI wireless card - it does the exact same thing. Compared all wireless settings to my laptop. I can ping google.com and it replies (sometimes with packet loss) When I reboot the PC it will connect for a minute or two (random time) and then just stops again. I tried Firefox, IE etc. no joy I have updated all latest versions (Netgear WG111v2) and drivers Checked Event Log - nothing unusual Ping the router (and even connect as admin for the few minutes when the internet does work) Changed the MTU down to 1200 using DrTCP Checked Device Manager for conflicts - none. I ping the router from the PC (192.168.0.10 - 192.168.0.1) and it replies with 4 packets. BUT, on my router admin page (which I access via http on my laptop wirelessly) - if I ping 192.168.0.10 all packets timeout (pinging my laptop 192.168.0.12 works fine) My router admin page shows the leased IP address for 192.168.0.10 (ie it is definitely talking to the router initially) Now I am out of ideas - please help. I think it is an OS/Software issue as I have tried 2 different wireless adapaters (PCI and USB) with the same result but all other wireless devices work fine around mine). It's not the firewall. It is getting assigned an IP address correctly (my PC gets 192.168.0.10, my laptop is .12) It is assigned by DHCP. As soon as I plug in the ethernet cable it all works fine. Repairing the adapter sometimes helps but it will always stop working after a random time. The wireless adapter always shows as connected with Excellent signal but the internet does not work. I am running Windows XP SP3 and have tried a Netgear WG111v2 USB adapter. Thanks in advance! UPDATE: The internet seems to be working, it is just either sending packets too small or slow to work (some small pages load bits of them very slowly but then hang). XP seems to have a networking diagnostic app - here is the output: Last diagnostic run time: 08/30/10 08:16:38 IP Configuration Diagnostic Invalid IP address info Valid IP address detected: 192.168.0.10 IP Layer Diagnostic Corrupted IP routing table info The default route is valid info The loopback route is valid info The local host route is valid info The local subnet route is valid Invalid ARP cache entries action The ARP cache has been flushed Gateway Diagnostic Gateway info The following proxy configuration is being used by IE: Automatically Detect Settings:Disabled Automatic Configuration Script: Proxy Server: Proxy Bypass list: info This computer has the following default gateway entry(ies): 192.168.0.1 info This computer has the following IP address(es): 192.168.0.10 info The default gateway is in the same subnet as this computer info The default gateway entry is a valid unicast address info The default gateway address was resolved via ARP in 1 try(ies) info The default gateway was reached via ICMP Ping in 1 try(ies) info TCP port 80 on host 65.55.12.249 was successfully reached info The Internet host www.microsoft.com was successfully reached info The default gateway is OK DNS Client Diagnostic DNS - Not a home user scenario info Using Web Proxy: no info Resolving name ok for (www.microsoft.com): yes No DNS servers DNS failure HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Passive): Successfully connected to ftp.microsoft.com. info HTTP: Successfully connected to www.microsoft.com. warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out error Could not make an HTTPS connection. info Redirecting user to support call WinSock Diagnostic WinSock status info All base service provider entries are present in the Winsock catalog. info The Winsock Service provider chains are valid. info Provider entry MSAFD Tcpip [TCP/IP] passed the loopback communication test. info Provider entry MSAFD Tcpip [UDP/IP] passed the loopback communication test. info Provider entry RSVP UDP Service Provider passed the loopback communication test. info Provider entry RSVP TCP Service Provider passed the loopback communication test. info Connectivity is valid for all Winsock service providers. Wireless Diagnostic Wireless - Service disabled Wireless - User SSID action User input required: Specify network name or SSID Wireless - First time setup info The Wireless Network name (SSID) to which the user would like to connect = RodSof Wifi. Wireless - Radio off info Valid IP address detected: 192.168.0.10 Wireless - Out of range Wireless - Hardware issue Wireless - Novice user Wireless - Ad-hoc network Wireless - Less preferred Wireless - 802.1x enabled Wireless - Configuration mismatch Wireless - Low SNR Network Adapter Diagnostic Network location detection info Using home Internet connection Network adapter identification info Network connection: Name=Local Area Connection 2, Device=Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC, MediaType=LAN, SubMediaType=LAN info Network connection: Name=Wireless USB, Device=NETGEAR WG111v2 54Mbps Wireless USB 2.0 Adapter, MediaType=LAN, SubMediaType=WIRELESS info Both Ethernet and Wireless connections available, prompting user for selection action User input required: Select network connection info Wireless connection selected Network adapter status info Network connection status: Connected HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Active): Successfully connected to ftp.microsoft.com. warn HTTP: Error 12007 connecting to www.microsoft.com: The server name or address could not be resolved warn HTTP: Error 12002 connecting to www.hotmail.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out error Could not make an HTTP connection. error Could not make an HTTPS connection.

    Read the article

  • Mount TMPFS instead of ro /dev

    - by schiggn
    I am working on a ARM-Based embedded system with a custom Debian Linux based on kernel 2.6.31. In the final system, the Root file system is stored as squashfs on flash. Now, the folder /dev is created by udev, but since there is no hot plugging functionality needed and booting time is critical, I wanted to delete udev and "hard code" the /dev folder (read here, page 5). because i still need to change parameters of the devices (with ioctl /sysfs) this does not work for me in this case. so i thought of mounting a tmpfs on /dev and change the parameters there. is this possible? and how to do best? my approach would be: delete /dev from RFS create tar containing basic devices mount tmpfs /dev untar tar-file into /dev change parameters Could this work? Do you see any problems? I found out, that you can mount on top of already mounted mount point, is it somehow possible just to take data with while mounting the new file system? if so that would be very convenient! Thanks Update: I just tried that out, but I'm stuck at a certain point. I packed all my devices into devices.tar, packed it into /usr of my squashfs and added the following lines to mountkernfs.sh, which is executed right after INIT. #mount /dev on tmpfs echo -n "Mounting /dev on tmpfs..." mount -o size=5M,mode=0755 -t tmpfs tmpfs /dev mknod -m 600 /dev/console c 5 1 mknod -m 600 /dev/null c 1 3 echo "done." echo -n "Populating /dev..." tar -xf /usr/devices.tar -C /dev echo "done." This works fine on the version over NFS, if I place printf's in the code, I can see it executing, if I comment out the extracting part, its complaining about missing devices. Booting OK mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 IP-Config: Unable to set interface netmask (-22). Looking up port of RPC 100003/2 on 192.168.1.234 Looking up port of RPC 100005/1 on 192.168.1.234 VFS: Mounted root (nfs filesystem) on device 0:14. Freeing init memory: 136K INIT: version 2.86 booting Mounting /dev on tmpfs...done. Populating /dev...done. Initializing /var...done. Setting the system clock. System Clock set to: Thu Sep 13 11:26:23 UTC 2012. INIT: Entering runlevel: 2 UBI: attaching mtd8 to ubi0 Commenting out the extraction of the tar mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 IP-Config: Unable to set interface netmask (-22). Looking up port of RPC 100003/2 on 192.168.1.234 Looking up port of RPC 100005/1 on 192.168.1.234 VFS: Mounted root (nfs filesystem) on device 0:14. Freeing init memory: 136K INIT: version 2.86 booting Mounting /dev on tmpfs...done. Populating /dev...done. Initializing /var...done. Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Thu Sep 13 12:24:00 UTC 2012 ... (warning). INIT: Entering runlevel: 2 libubi: error!: cannot open "/dev/ubi_ctrl" So far so good. But if I pack the whole story into a squashfs and boot from there, it is acting strange. It's telling me while booting that it is unable to open an initial console and its throwing errors on mounting the UBIFS devices, but finally provides a login anyway. Over that my echo's are not executed. If I then log in, /dev is mounted as TMPFS as desired and all the devices reside inside. When I redo the "mount" command to mount the UBIFS partitions it is executed whitout problem and useable. From squashfs VFS: Mounted root (squashfs filesystem) readonly on device 31:15. Freeing init memory: 136K Warning: unable to open an initial console. mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 UBIFS error (pid 484): ubifs_get_sb: cannot open "ubi1_0", error -19 Additionally, a part of the rest of the bootscripts is still exexuted, but not all of them. Does anyone has a clue why? Other question, is 5MB enough/too much for /dev?

    Read the article

  • Server hung with "blocked for more than 120 seconds", diskless

    - by alterpub
    I have server which hung every 2-5 days. dmesg show following situation: kernel: [490894.231753] INFO: task munin-html:10187 blocked for more than 120 seconds. kernel: [490894.231799] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kernel: [490894.231843] munin-html D 0000000000000000 0 10187 9796 0x00000000 kernel: [490894.231878] ffff88063174b968 0000000000000082 ffff88063174b8d8 0000000000015b80 kernel: [490894.231930] ffff88063174bfd8 0000000000015b80 ffff88063174bfd8 ffff88062fe644d0 kernel: [490894.231982] 0000000000015b80 0000000000015b80 ffff88063174bfd8 0000000000015b80 kernel: [490894.232033] Call Trace: kernel: [490894.232059] [<ffffffff8117fce0>] ? sync_buffer+0x0/0x50 kernel: [490894.232089] [<ffffffff815a1f13>] io_schedule+0x73/0xc0 kernel: [490894.232115] [<ffffffff8117fd25>] sync_buffer+0x45/0x50 kernel: [490894.232143] [<ffffffff815a258f>] __wait_on_bit+0x5f/0x90 kernel: [490894.232170] [<ffffffff8117fce0>] ? sync_buffer+0x0/0x50 kernel: [490894.232197] [<ffffffff815a2638>] out_of_line_wait_on_bit+0x78/0x90 kernel: [490894.232227] [<ffffffff81080250>] ? wake_bit_function+0x0/0x40 kernel: [490894.232255] [<ffffffff8117fcd6>] __wait_on_buffer+0x26/0x30 kernel: [490894.232288] [<ffffffffa00131be>] squashfs_read_data+0x1be/0x520 [squashfs] kernel: [490894.232320] [<ffffffff8114f0f1>] ? __mem_cgroup_try_charge+0x71/0x450 kernel: [490894.232350] [<ffffffffa0013963>] squashfs_cache_get+0x1c3/0x320 [squashfs] kernel: [490894.232381] [<ffffffffa00136eb>] ? squashfs_copy_data+0x10b/0x130 [squashfs] kernel: [490894.232426] [<ffffffff815a3dbe>] ? _raw_spin_lock+0xe/0x20 kernel: [490894.232454] [<ffffffffa0013b68>] ? squashfs_read_metadata+0x48/0xf0 [squashfs] kernel: [490894.232499] [<ffffffffa0013ae1>] squashfs_get_datablock+0x21/0x30 [squashfs] kernel: [490894.232544] [<ffffffffa0015026>] squashfs_readpage+0x436/0x4a0 [squashfs] kernel: [490894.232575] [<ffffffff8111a375>] ? __inc_zone_page_state+0x35/0x40 kernel: [490894.232606] [<ffffffff8110d072>] __do_page_cache_readahead+0x172/0x210 kernel: [490894.232636] [<ffffffff8110d131>] ra_submit+0x21/0x30 kernel: [490894.232662] [<ffffffff811045f3>] filemap_fault+0x3f3/0x450 kernel: [490894.232691] [<ffffffff812bd156>] ? prio_tree_insert+0x256/0x2b0 kernel: [490894.232726] [<ffffffffa009225d>] aufs_fault+0x11d/0x170 [aufs] kernel: [490894.232755] [<ffffffff8111f6d4>] __do_fault+0x54/0x560 kernel: [490894.232782] [<ffffffff81122f39>] handle_mm_fault+0x1b9/0x440 kernel: [490894.232811] [<ffffffff811286f5>] ? do_mmap_pgoff+0x335/0x380 kernel: [490894.232840] [<ffffffff815a7af5>] do_page_fault+0x125/0x350 kernel: [490894.232867] [<ffffffff815a4675>] page_fault+0x25/0x30 Os info cat /etc/issue.net Ubuntu 10.04.2 LTS uname -a Linux Shard1Host3 2.6.35-32-server #68~lucid1-Ubuntu SMP Wed Mar 28 18:33:00 UTC 2012 x86_64 GNU/Linux This system load via ltsp and hasn't harddrives also it has a lot of memory 24Gb. free -m total used free shared buffers cached Mem: 24152 17090 7061 0 50 494 -/+ buffers/cache: 16545 7607 Swap: 0 0 0 I put vmstat info here but I think it won't give results after reboot vmstat 1 30 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 7231156 52196 506400 0 0 0 0 172 143 7 0 92 0 1 0 0 7231024 52196 506400 0 0 0 0 7859 16233 5 0 94 0 0 0 0 7231024 52196 506400 0 0 0 0 7870 16446 2 0 98 0 0 0 0 7230900 52196 506400 0 0 0 0 7308 15661 5 0 95 0 0 0 0 7231100 52196 506400 0 0 0 0 7960 16543 6 0 94 0 0 0 0 7231100 52196 506400 0 0 0 0 7542 16047 5 1 94 0 3 0 0 7231100 52196 506400 0 0 0 0 7709 16621 3 0 96 0 0 0 0 7231220 52196 506400 0 0 0 0 7857 16552 4 0 96 0 0 0 0 7231220 52196 506400 0 0 0 0 7192 15491 6 0 94 0 0 0 0 7231220 52196 506400 0 0 0 0 7423 15792 5 1 94 0 1 0 0 7231260 52196 506404 0 0 0 0 7686 16296 2 0 98 0 0 0 0 7231260 52196 506404 0 0 0 0 6976 15183 5 0 95 0 0 0 0 7231260 52196 506404 0 0 0 0 7303 15600 4 0 95 0 0 0 0 7231320 52196 506404 0 0 0 0 7967 16241 1 0 98 0 0 0 0 7231444 52196 506404 0 0 0 0 6948 15113 6 0 94 0 0 0 0 7231444 52196 506404 0 0 0 0 7931 16181 6 0 94 0 1 0 0 7231516 52196 506404 0 0 0 0 7715 15829 6 0 94 0 0 0 0 7231516 52196 506404 0 0 0 0 7771 16036 2 0 97 0 0 0 0 7231268 52196 506404 0 0 0 0 7782 16202 6 0 94 0 1 0 0 7231212 52196 506404 0 0 0 0 7457 15622 4 0 96 0 0 0 0 7231212 52196 506404 0 0 0 0 7573 16045 2 0 98 0 2 0 0 7231216 52196 506404 0 0 0 0 7689 16076 6 0 94 0 0 0 0 7231424 52196 506404 0 0 0 0 7429 15650 4 0 95 0 3 0 0 7231424 52196 506404 0 0 0 0 7534 16168 3 0 97 0 1 0 0 7230548 52196 506404 0 0 0 0 8559 15926 7 1 92 0 0 0 0 7230672 52196 506404 0 0 0 0 7720 15905 2 0 98 0 0 0 0 7230548 52196 506404 0 0 0 0 7677 16313 5 0 95 0 1 0 0 7230676 52196 506404 0 0 0 0 7209 15432 5 0 95 0 0 0 0 7230800 52196 506404 0 0 0 0 7522 15861 2 0 98 0 0 0 0 7230552 52196 506404 0 0 0 0 7760 16661 5 0 95 0 In the munin(monitoring system) graphs I see(before server hung): Disk(nbd0) IOs per device: read: 289m but avg by week 2.09m Disk(nbd0) throughput per device: read: 4.73k but avg by week 108.76 Disk(nbd0) utilization per device: 100% but avg by week 1.2% Eth0 traffic was low: in/out only 2Mbps Number of threads increased to 566 usually 392 Fork rate 1.08 but usually 2.82 VMStat(processes state) Increased to 17.77(from 0 as far as I could see in the graph) CPU usage iowait 880.46% when usually 6.67% It'll be great if somebody help me to understand what's up.

    Read the article

  • Why is my mdadm raid-1 recovery so slow?

    - by dimmer
    On a system I'm running Ubuntu 10.04. My raid-1 restore started out fast but quickly became ridiculously slow (at this rate the restore will take 150 days!): dimmer@paimon:~$ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdc1[2] sdb1[1] 1953513408 blocks [2/1] [_U] [====>................] recovery = 24.4% (477497344/1953513408) finish=217368.0min speed=113K/sec unused devices: <none> Eventhough I have set the kernel variables to reasonably quick values: dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_min 1000000 dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_max 100000000 I am using 2 2.0TB Western Digital Hard Disks, WDC WD20EARS-00M and WDC WD20EARS-00J. I believe they have been partitioned such that their sectors are aligned. dimmer@paimon:/sys$ sudo parted /dev/sdb GNU Parted 2.2 Using /dev/sdb Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00M (scsi) Disk /dev/sdb: 2000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 (parted) unit s (parted) p Number Start End Size File system Name Flags 1 2048s 3907028991s 3907026944s ext4 (parted) q dimmer@paimon:/sys$ sudo parted /dev/sdc GNU Parted 2.2 Using /dev/sdc Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00J (scsi) Disk /dev/sdc: 2000GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 I am beginning to think that I have a hardware problem, otherwise I can't imagine why the mdadm restore should be so slow. I have done a benchmark on /dev/sdc using Ubuntu's disk utility GUI app, and the results looked normal so I know that sdc has the capability to write faster than this. I also had the same problem on a similar WD drive that I RMAd because of bad sectors. I suppose it's possible they sent me a replacement with bad sectors too, although there are no SMART values showing them yet. Any ideas? Thanks. As requested, output of top sorted by cpu usage (notice there is ~0 cpu usage). iowait is also zero which seems strange: top - 11:35:13 up 2 days, 9:40, 3 users, load average: 2.87, 2.58, 2.30 Tasks: 142 total, 1 running, 141 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.2%sy, 0.0%ni, 99.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3096304k total, 1482164k used, 1614140k free, 617672k buffers Swap: 1526132k total, 0k used, 1526132k free, 535416k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 45 root 20 0 0 0 0 S 0 0.0 2:17.02 scsi_eh_0 1 root 20 0 2808 1752 1204 S 0 0.1 0:00.46 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/0 4 root 20 0 0 0 0 S 0 0.0 0:00.17 ksoftirqd/0 5 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 6 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/1 ... dmesg errors, definitely looking like hardware: [202884.000157] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [202884.007015] ata5.00: failed command: FLUSH CACHE EXT [202884.013728] ata5.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [202884.013730] res 40/00:00:ff:59:2e/00:00:35:00:00/e0 Emask 0x4 (timeout) [202884.033667] ata5.00: status: { DRDY } [202884.040329] ata5: hard resetting link [202889.400050] ata5: link is slow to respond, please be patient (ready=0) [202894.048087] ata5: COMRESET failed (errno=-16) [202894.054663] ata5: hard resetting link [202899.412049] ata5: link is slow to respond, please be patient (ready=0) [202904.060107] ata5: COMRESET failed (errno=-16) [202904.066646] ata5: hard resetting link [202905.840056] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [202905.849178] ata5.00: configured for UDMA/133 [202905.849188] ata5: EH complete [203899.000292] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [203899.007096] ata5.00: failed command: IDENTIFY DEVICE [203899.013841] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [203899.013843] res 40/00:00:ff:f9:f6/00:00:38:00:00/e0 Emask 0x4 (timeout) [203899.041232] ata5.00: status: { DRDY } [203899.048133] ata5: hard resetting link [203899.816134] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [203899.826062] ata5.00: configured for UDMA/133 [203899.826079] ata5: EH complete [204375.000200] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204375.007421] ata5.00: failed command: IDENTIFY DEVICE [204375.014799] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204375.014800] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204375.044374] ata5.00: status: { DRDY } [204375.051842] ata5: hard resetting link [204380.408049] ata5: link is slow to respond, please be patient (ready=0) [204384.440076] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204384.449938] ata5.00: configured for UDMA/133 [204384.449955] ata5: EH complete [204395.988135] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204395.988140] ata5.00: failed command: IDENTIFY DEVICE [204395.988147] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204395.988149] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204395.988151] ata5.00: status: { DRDY } [204395.988156] ata5: hard resetting link [204399.320075] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204399.330487] ata5.00: configured for UDMA/133 [204399.330503] ata5: EH complete

    Read the article

  • dynatree: how can i select child node programmatically

    - by Muhammad Adeel Zahid
    hello everyone i m using jquery's dynaTree in my application and i want to select the all the child nodes programmably when a node is selected. the structure of my tree is as follows <div id = "tree"> <ul> <li>package 1 <ul> <li>module 1.1 <ul> <li> document 1.1.1</li> <li> document 1.1.2</li> </ul> </li> <li>module 1.2 <ul> <li>document 1.2.1</li> <li>document 1.2.2</li> </ul> </li> </ul> </li> <li> package 2 <ul> <li> module 2.1 <ul> <li>document 2.1.1</li> <li>document 2.1.1</li> </ul> </li> </ul> </li> </ul> </div> now what i want is that when i click on tree node with title "package 1" all its child nodes i.e (module 1.1, document 1.1.1, document 1.1.2, module 1.2, document 1.2.1, document 1.2.2) should also be selected below is the approach i tried to use $("#tree").dynatree({ onSelect: function(flag, dtnode) { // This will happen each time a check box is selected/deselected var selectedNodes = dtnode.tree.getSelectedNodes(); var selectedKeys = $.map(selectedNodes, function(node) { //alert(node.data.key); return node.data.key; }); // Set the hidden input field's value to the selected items $('#SelectedItems').val(selectedKeys.join(",")); if (flag) { child = dtnode.childList; alert(child.length); for (i = 0; i < child.length; i++) { var x = child[i].select(true); alert(i); } } }, checkbox: true, onActivate: function(dtnode) { //alert("You activated " + dtnode.data.key); } }); in the if(flag) condition i get all the child nodes of element that is selected by user and it gives me the correct value that i can see from alert(child.length) statement. then i run the loop to select all the children but loop never goes beyond the statement var x = child[i].select(true); and i can never see the statement alert(i) being executed. the result of above statement is that if i select package 1, module 1.1 and document 1.1.1 is also selected but never does it execute alert(i) statement neither other children of package 1 are selected. in my view when first time child[i].select(true) statement is executed it also triggers the on select event of its children thus making a recursion kind of thing is my thinking correct? no matter recursion or what why on earth does it not complete the loop and execute very next instruction alert(i). please help me in solving this problem. i m dying to see that alert any suggestion and help is highly appriciated thanks Adeel

    Read the article

< Previous Page | 291 292 293 294 295 296 297 298 299 300 301 302  | Next Page >