Search Results

Search found 20188 results on 808 pages for 'wireless network'.

Page 3/808 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• How do I get wireless to work on a Dell Mini 1018 with Realtek RTL 8188CE Network Adapter?

  - by Laurence Nagel

  My Dell Mini 1018 used to work fine with Ubuntu 12.04 with no problems connecting with the wireless card. Then I made the big mistake of attempting to disable WiFi by right-clicking on the wireless applet and un-checking "Enable Wireless." Since then, I cannot get wireless working again. The wireless applet reports that "wireless is disabled by hardware switch" but there is no hardware switch on this computer. Issuing a rfkill list yields the following: 0: dell-wifi: Wireless LAN Soft blocked: yes Hard block: yes 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I'm in way over my head, and my computer is now useless. Help!!!

  Read the article

• Atheros AR2413 wireless not working after shutdown

  - by Chandrasekhar

  I am using a Ubuntu 11.04 on an Acer aspire 3680 laptop and my wifi is not working. I followed the below commands to install the madwifi driver: sudo su apt-get install subversion cd /usr/src svn checkout http://madwifi-project.org/svn/madwifi/trunk madwifi tar cfvz madwifi.tgz cd madwifi make && make install echo "blacklist ath5k" /etc/modprobe.d/blacklist.conf echo "ath_pci" /etc/modules modprobe ath_pci sudo reboot After installation I am facing the same problem. My wifi wont work after I shutdown. Infact it didn't work after suspend but I rectified that problem by the following commands: Command 1: sudo rmmod -f ath_pci sudo rfkill unblock all sudo modprobe ath_pci along with the command SUSPEND_MODULES=ath_pci added to the /etc/pm/config.d/madwifi directory. So if I suspend and then on my laptop the wifi loads well and doesn't create a problem. But if I shutdown my laptop the wifi never loads again and eachtime I have to run a Ubuntu 9.04 live CD to load it. I did try adding the Command 1 to the /etc/rc.local directory but still it doesn't work. So my question is: What should I do in order to make my wireless work without having to run a live CD of ubuntu 9.04 everytime after shutdown? Thanks. Here are the outputs which one might need: Output 1 chandru@chandru-acer:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 0a:03.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) 0a:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) Output 2: lsmod Module Size Used by wlan_tkip 17074 2 binfmt_misc 13213 1 parport_pc 32111 0 ppdev 12849 0 snd_hda_codec_si3054 12924 1 snd_hda_codec_realtek 255882 1 joydev 17322 0 snd_atiixp_modem 18624 0 snd_via82xx_modem 18305 0 snd_intel8x0m 18493 0 snd_ac97_codec 105614 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m snd_hda_intel 24113 2 ac97_bus 12642 1 snd_ac97_codec snd_hda_codec 90901 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel i915 451053 3 snd_hwdep 13274 1 snd_hda_codec snd_pcm 80042 7 snd_hda_codec_si3054,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25269 1 snd_seq_midi drm_kms_helper 40971 1 i915 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event pcmcia 39671 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq drm 184164 4 i915,drm_kms_helper yenta_socket 27230 0 tifm_7xx1 12898 0 wlan_scan_sta 21945 1 ath_rate_sample 17279 1 pcmcia_rsrc 18292 1 yenta_socket psmouse 73312 0 tifm_core 15040 1 tifm_7xx1 snd 55295 18 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device serio_raw 12990 0 i2c_algo_bit 13184 1 i915 soundcore 12600 1 snd pcmcia_core 21505 3 pcmcia,yenta_socket,pcmcia_rsrc video 19112 1 i915 ath_pci 183044 0 snd_page_alloc 14073 5 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci lp 13349 0 parport 36746 3 parport_pc,ppdev,lp usbhid 41704 0 hid 77084 1 usbhid sky2 49172 0 Output 3 root@chandru-acer:~# lshw -C network PCI (sysfs) *-network description: Ethernet interface product: 88E8038 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 14 serial: 00:16:36:fb:aa:64 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.28 firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:44000000-44003fff ioport:2000(size=256) *-network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wifi0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci ip=192.168.1.6 latency=96 maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11g resources: irq:18 memory:d0000000-d000ffff Output 4 root@chandru-acer:~# lsmod | grep ath_pci ath_pci 183044 0 wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci

  Read the article

• Wireless will not work in fresh ubuntu 12.04 lts installation

  - by Taake Manning

  I did a fresh Ubuntu 12.04 install on my Sony Vaio laptop, which worked perfectly with 10.04. Now my wireless won't work. I have read just about every Q&A on the subject and I have tried different solutions, including the official troubleshooting guides. My laptop is equipped with a Intel 5100 wireless device. Ubuntu recognizes the device and it's status is given as connected in nm-tool. I can ping the gateway, my own IP number and localhost. Rfkill shows no soft or hard blocks. Any ideas? I am just a few hours shy of reinstalling good old 10.04! Taake

  Read the article

• How do I ban a wifi network in Network Manager?

  - by Chris Conway

  My wifi connection drops sometimes and, for some reason, Network Manager attempts to connect to my neighbor's network, which requires a password that I don't know. The network in question is not listed in the "Edit Connections..." dialog and I can find no reference to it in any configuration file, but still the password dialog pops up every time my main connection drops. Is there a way to blacklist a wireless network so that the Network Manager will never attempt to connect to it? Or, equivalently, how can I remove the configuration data that causes the Network Manager to attempt to connect to this particular network?

  Read the article

• How can I prioritize wireless networks with network-manager

  - by kynan

  Mostly I use my laptop in an environment where different wireless networks are available and I would like to preferably connect to one of those and only fall back to the other one if that one is not available. Is there any way of prioritizing which wireless networks network-manager preferably connects to? The only workaround I found so far was unchecking Connect Automatically in the options and re-enabling it when my preferred network is not available.

  Read the article

• Pluscom MAC address shows up but "wireless unavailable"

  - by Luigi

  I've got a pluscom pci card plugged into my desktop and although the mac address shows up in network manager, it says "Wireless unavailable". I'm using Ubuntu 12.10 Gnome Shell Remix... edgar@edgarQuantal:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off edgar@edgarQuantal:~$ ifconfig eth0 Link encap:Ethernet HWaddr 6c:f0:49:02:1f:b8 inet addr:192.168.0.7 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fe02:1fb8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1425 errors:0 dropped:0 overruns:0 frame:0 TX packets:1393 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:995753 (995.7 KB) TX bytes:134079 (134.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:363 errors:0 dropped:0 overruns:0 frame:0 TX packets:363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:40828 (40.8 KB) TX bytes:40828 (40.8 KB) It looks the same as the problem as here, seems quite complicated: http://ubuntuforums.org/showthread.php?t=1993226 Tried downloading the driver but i get this: "Unpacking firmware-ralink (from .../firmware-ralink_0.36_all.deb) ... dpkg: error processing /home/edgar/Downloads/firmware-ralink_0.36_all.deb (--install): trying to overwrite '/lib/firmware/rt2870.bin', which is also in package linux-firmware 1.95"

  Read the article

• Virtualbox completely disabled my ethernet and wireless network connections

  - by Tawani

  After installing VirtualBox 3.1.6 for Windows, my computer's network connections were completely disabled. The wireless isn't working, not even the ethernet landline. Even "ipconfig" doesn't seem to respond to any commands. Can anybody help?

  Read the article

• Wireless Problem on Acer Aspire 5610z

  - by Ugur Can Yalaki

  I installed ubuntu 12.04 on my machine, but I can't get wireless connection to work. My computer is Acer Aspire 5610z. I found that some other people that have same computer, face the same problem. Here is some information about it: ****** info trace ****** * uname -a * Linux ucy-Aspire-5610Z 3.8.0-32-generic #47~precise1-Ubuntu SMP Wed Oct 2 16:22:28 UTC 2013 i686 i686 i386 GNU/Linux * lsb_release * Distributor ID: Ubuntu Description: Ubuntu 12.04.3 LTS Release: 12.04 Codename: precise * lspci * 05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) Subsystem: AMBIT Microsystem Corp. Device [1468:0422] Kernel driver in use: b43-pci-bridge 06:01.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02) Subsystem: Acer Incorporated [ALI] Device [1025:0090] Kernel driver in use: b44 * lsusb * Bus 001 Device 004: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 5986:0100 Acer, Inc Orbicam Bus 002 Device 002: ID 046d:c52f Logitech, Inc. Wireless Mouse M305 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub * PCMCIA Card Info * PRODID_1="" PRODID_2="" PRODID_3="" PRODID_4="" MANFID=0000,0000 FUNCID=255 * iwconfig * * rfkill * 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no * lsmod * ssb_hcd 12781 0 ssb 51554 2 ssb_hcd,b44 * nm-tool * NetworkManager Tool State: connected (global) Device: usb0 [Wired connection 2] ------------------------------------------- Type: Wired Driver: rndis_host State: connected Default: yes HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: on IPv4 Settings: Address: 192.168.42.7 Prefix: 24 (255.255.255.0) Gateway: 192.168.42.129 DNS: 192.168.42.129 IPv6 Settings: Address: ::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 Address: fe80::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 DNS: fe80::504d:76ff:fe86:db04 Device: eth2 ----------------------------------------------------------------- Type: Wired Driver: b44 State: unavailable Default: no HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: off * NetworkManager.state * [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true * NetworkManager.conf * [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false * interfaces * auto lo iface lo inet loopback * iwlist * * resolv.conf * nameserver 127.0.0.1 * blacklist * [/etc/modprobe.d/blacklist-ath_pci.conf] blacklist ath_pci [/etc/modprobe.d/blacklist-bcm43.conf] blacklist b43 blacklist b43legacy blacklist ssb blacklist bcm43xx blacklist brcm80211 blacklist brcmfmac blacklist brcmsmac blacklist bcma [/etc/modprobe.d/blacklist.conf] blacklist evbug blacklist usbmouse blacklist usbkbd blacklist eepro100 blacklist de4x5 blacklist eth1394 blacklist snd_intel8x0m blacklist snd_aw2 blacklist i2c_i801 blacklist prism54 blacklist bcm43xx blacklist garmin_gps blacklist asus_acpi blacklist snd_pcsp blacklist pcspkr blacklist amd76x_edac * modinfo * filename: /lib/modules/3.8.0-32-generic/kernel/drivers/usb/host/ssb-hcd.ko license: GPL description: Common USB driver for SSB Bus author: Hauke Mehrtens srcversion: E127A51EDC8F44D2C2A8F15 alias: ssb:v4243id0819rev* alias: ssb:v4243id0817rev* alias: ssb:v4243id0808rev* depends: ssb intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 filename: /lib/modules/3.8.0-32-generic/kernel/drivers/ssb/ssb.ko license: GPL description: Sonics Silicon Backplane driver srcversion: 14621F6EC014F731244437C alias: pci:v000014E4d00004350sv*sd*bc*sc*i* alias: pci:v000014E4d0000432Csv*sd*bc*sc*i* alias: pci:v000014E4d0000432Bsv*sd*bc*sc*i* alias: pci:v000014E4d00004329sv*sd*bc*sc*i* alias: pci:v000014E4d00004328sv*sd*bc*sc*i* alias: pci:v000014E4d00004325sv*sd*bc*sc*i* alias: pci:v000014E4d00004324sv*sd*bc*sc*i* alias: pci:v000014E4d0000A8D6sv*sd*bc*sc*i* alias: pci:v000014E4d00004322sv*sd*bc*sc*i* alias: pci:v000014E4d00004321sv*sd*bc*sc*i* alias: pci:v000014E4d00004320sv*sd*bc*sc*i* alias: pci:v000014E4d00004319sv*sd*bc*sc*i* alias: pci:v000014A4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004315sv*sd*bc*sc*i* alias: pci:v000014E4d00004312sv*sd*bc*sc*i* alias: pci:v000014E4d00004311sv*sd*bc*sc*i* alias: pci:v000014E4d00004307sv*sd*bc*sc*i* alias: pci:v000014E4d00004306sv*sd*bc*sc*i* alias: pci:v000014E4d00004301sv*sd*bc*sc*i* depends: intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 * udev rules * PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb1:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb2:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb3:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth2" * dmesg * [ 2.385241] ssb: Found chip with id 0x4311, rev 0x01 and package 0x00 [ 2.385256] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x11, vendor 0x4243) [ 2.385266] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0A, vendor 0x4243) [ 2.385276] ssb: Core 2 found: USB 1.1 Host (cc 0x817, rev 0x03, vendor 0x4243) [ 2.385286] ssb: Core 3 found: PCI-E (cc 0x820, rev 0x01, vendor 0x4243) [ 2.448147] ssb: Sonics Silicon Backplane found on PCI device 0000:05:00.0 [ 2.468112] ssb: Found chip with id 0x4401, rev 0x02 and package 0x00 [ 2.468124] ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x07, vendor 0x4243) [ 2.468132] ssb: Core 1 found: V90 (cc 0x807, rev 0x03, vendor 0x4243) [ 2.468140] ssb: Core 2 found: PCI (cc 0x804, rev 0x0A, vendor 0x4243) [ 2.508230] ssb: Sonics Silicon Backplane found on PCI device 0000:06:01.0 [ 2.528620] b44 ssb1:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver ******** done ******** Thank you already for your help.

  Read the article

• wireless not showing up in network manager applet.

  - by Vidur Vishnudutt

  there is only the wired connection option available when the menu drops down. i have installed a belkin wireless g card for my desktop. it has been used before on this version of ubuntu 10.10, but after upgrading it shows only wired networks. enable networking and enable notifications have both been ticked. still only wired networks coming. im using ubuntu 10.10 maverick meerkat on my desktop comp and im an absolute begginer at ubuntu. can some one please help me re enable wireless on my comp?

  Read the article

• Setting up a WPA-PSK network card to connect to a WPA2 network

  - by mattshepherd

  I'm currently doing a spare-parts build to put a media computer in the living room, and having a devil of a time getting my Rosewill RNX-6300 wireless card to connect to my network. I'm trying to set it up using Windows as opposed to the proprietary Rosewill software -- the Rosewill software is a little over my head. It can find the network fine, but when I try to connect, I don't get the password prompt -- it moves straight to "validating identity," scans, and then says "Windows was not able to find a certificate to log you on to the wireless network Foo." The maddening thing is that the card was working fine a week ago, in the same box, using the same OS. I pulled everything out, swapped out the motherboard, and reinstalled Windows on a freshly wiped hard drive, and now I can't get it up and running again. Suggestions? I've taken several runs at it, including attempting to manually change the settings for the network to include WPA-PSK and AES and the password, and I'm a bit worried that I've totally boned everything. My router settings: ipconfig/all results from the XP box: Again, this card was working on this network a week ago. I can't figure out why I can't get it up and running now. There's no WPA2 on the card, just WPA and WPA-PSK: WPA-PSK was the only setting that would let me enter a network key. I had TKIP and AES as options there, but cipher type is AES on the router, so I chose that. (I tried TKIP later, when this didn't work, with the same results as described below.) So I set it to WPA-PSK / AES and entered my security key. It's mixed letters and numbers, 32 characters long. No joy. Still "waiting for reply" in the main screen, and "cannot find certificate" on the pop-up. And if I try again and return to the settings again, it is reset to Open/AES. It also re-enables 802.1x in the Authentication tab if I've deselected it with WPA-PSK. It also reshortens the password. I have no idea how I blundered into getting this working in the past. I am, as you can tell, far from proficient at this. It was working before, though. What am I getting wrong?

  Read the article

• Wireless connection keeps losing connection

  - by Santiago

  I'm having this annoying problem with my Ubuntu 12.04.1, upgraded from 10.04. The thing is that my wireless connection keeps going out of connection every 15-20 minutes, and sometimes I have to reboot my laptop. I've started having this problem about 1 month ago, but back in my 10.04 I had the same problem. If anyone has any idea it would be great. Also any info you need about the laptop, please tell me the commands I need to run to give it to you. Thanks and hope you help me.

  Read the article

• Cannot enable wireless on an Intel WifiLink 1000 on an Lenovo Ideapad z570

  - by Brij

  I am using the ubuntu 11.10 on lenovo ideapad z570. My wireless internet is not working. I have ensure that wireless switch is on. Windows 7, wireless works great.However ubuntu 11.10 is not allowing me to enable wireless connection. I have run the following command and here is the status. sudo lshw -class network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:1c:a4:a4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:42 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: f0:de:f1:64:b6:62 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff Here is rfkill list all output: rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no Note : Windows 7, wireless card property shows that Intel WifiLink 1000 BGN. Could someone help me to fix this issue.

  Read the article

• Configure a wireless network that accepts any WPA2-PSK network key

  - by Michel

  I recently bought a UART WiFi module ( this one ) and configured it with right SSID but wrong password( and I don't know what it is ). The problem is that I can't reset this module to its manufacture settings and I can't connect to this module via serial port to configure it with some wire or cable. But I'm sure that my module is trying to connect my access point but with wrong network key ( because in logs of my access point I can see my module that trying to connect but it can't ) So, I wonder to know is there any way to create or configure a network (using some access point or something else) based on WPA2 Personal security that accepts any WPA2-PSK passwords ? Or is there any other solution for this problem ? If no, is there anyway to see what password this module using to connect to that network ? ( If yes, then I can change password of my network to that password and access to this module's admin panel ) I tried create an open network ( without any security key ) but my module just searches for WPA2 based networks ( I think ).

  Read the article

• Ubuntu 12.04 patched b43 driver compilation error

  - by Zed

  I tried this How do I install this patched b43 driver? guide to install patched b43 driver on Ubuntu 12.04 with 3.2.0-31-generic kernel but I can't pass compilation phase.Here is what I did: wget http://www.orbit-lab.org/kernel/compat-wireless-3-stable/v3.1/compat-wireless-3.1.1-1.tar.bz2 cd compat-wireless-3.1.1-1/ scripts/driver-select b43 make make -C /lib/modules/3.2.0-31-generic/build M=/home/marco/compat-wireless-3.1.1-1 modules make[1]: Entering directory `/usr/src/linux-headers-3.2.0-31-generic' CC [M] /home/marco/compat-wireless-3.1.1-1/compat/main.o In file included from /home/marco/compat-wireless-3.1.1-1/include/linux/compat-2.6.29.h:5:0, from /home/marco/compat-wireless-3.1.1-1/include/linux/compat-2.6.h:24, from <command-line>:0: include/linux/netdevice.h:1153:5: warning: "IS_ENABLED" is not defined [-Wundef] include/linux/netdevice.h:1153:15: error: missing binary operator before token "(" include/linux/netdevice.h: In function ‘netdev_uses_dsa_tags’: include/linux/netdevice.h:1421:9: error: ‘struct net_device’ has no member named ‘dsa_ptr’ include/linux/netdevice.h:1422:31: error: ‘struct net_device’ has no member named ‘dsa_ptr’ include/linux/netdevice.h: In function ‘netdev_uses_trailer_tags’: include/linux/netdevice.h:1431:9: error: ‘struct net_device’ has no member named ‘dsa_ptr’ include/linux/netdevice.h:1432:35: error: ‘struct net_device’ has no member named ‘dsa_ptr’ make[3]: *** [/home/marco/compat-wireless-3.1.1-1/compat/main.o] Error 1 make[2]: *** [/home/marco/compat-wireless-3.1.1-1/compat] Error 2 make[1]: *** [_module_/home/marco/compat-wireless-3.1.1-1] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.2.0-31-generic' make: *** [modules] Error 2 To fix that error I added #include <linux/kconfig.h> to /usr/src/linux-headers-3.2.0-31-generic/include/linux/netdevice.h but now I'm getting something else make make -C /lib/modules/3.2.0-31-generic/build M=/home/marco/compat-wireless-3.1.1-1 modules make[1]: Entering directory `/usr/src/linux-headers-3.2.0-31-generic' CC [M] /home/marco/compat-wireless-3.1.1-1/compat/main.o LD [M] /home/marco/compat-wireless-3.1.1-1/compat/compat.o CC [M] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.o In file included from /home/marco/compat-wireless-3.1.1-1/include/linux/bcma/bcma.h:9:0, from /home/marco/compat-wireless-3.1.1-1/drivers/bcma/bcma_private.h:8, from /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:8: /home/marco/compat-wireless-3.1.1-1/include/linux/ssb/ssb.h: In function ‘ssb_driver_register’: /home/marco/compat-wireless-3.1.1-1/include/linux/ssb/ssb.h:236:36: error: ‘THIS_MODULE’ undeclared (first use in this function) /home/marco/compat-wireless-3.1.1-1/include/linux/ssb/ssb.h:236:36: note: each undeclared identifier is reported only once for each function it appears in In file included from /home/marco/compat-wireless-3.1.1-1/drivers/bcma/bcma_private.h:8:0, from /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:8: /home/marco/compat-wireless-3.1.1-1/include/linux/bcma/bcma.h: In function ‘bcma_driver_register’: /home/marco/compat-wireless-3.1.1-1/include/linux/bcma/bcma.h:170:37: error: ‘THIS_MODULE’ undeclared (first use in this function) /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c: At top level: /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:12:20: error: expected declaration specifiers or ‘...’ before string constant /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:13:16: error: expected declaration specifiers or ‘...’ before string constant /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:182:1: warning: data definition has no type or storage class [enabled by default] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:182:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’ [-Wimplicit-int] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:182:1: warning: parameter names (without types) in function declaration [enabled by default] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:188:1: warning: data definition has no type or storage class [enabled by default] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:188:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’ [-Wimplicit-int] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:188:1: warning: parameter names (without types) in function declaration [enabled by default] make[3]: *** [/home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.o] Error 1 make[2]: *** [/home/marco/compat-wireless-3.1.1-1/drivers/bcma] Error 2 make[1]: *** [_module_/home/marco/compat-wireless-3.1.1-1] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.2.0-31-generic' make: *** [modules] Error 2 Any suggestion what to try next?

  Read the article

• Intel Centrino Wireless-N 1000 Again ! Ubuntu 13.04 x64

  - by vafa

  First I have to say that I tried everything written about this concept. The problem is that it stops working randomly in 3 main forms : 1 - sometimes it disconnect from wireless network and reconnect automatically 2 - sometimes it disconnect and wont connect no matter what (needs reboot) 3 - some times it's still connected but cannot ping or surf or whatever. I already tried disabling N mod using these commands : sudo modprobe -r iwlwifi modprobe iwlwifi 11n_disable=1 (or 0, whatever) it didn't help . these are the results of lspci, sudo lshw -C network, ifconfig, iwconfig, rfkill list when it disconnected and didn't connect till reboot : ifconfig : eth0 Link encap:Ethernet HWaddr c8:0a:a9:34:65:77 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1563213476557380 errors:9379306629148050 dropped:3126435543049350 overruns:1563217771524675 frame:7816088857623375 TX packets:1563217771524675 errors:6252871086098700 dropped:0 overruns:1563217771524675 carrier:3126435543049350 collisions:7816088857623375 txqueuelen:1000 RX bytes:1563217771524675 (1.5 PB) TX bytes:1563217771524675 (1.5 PB) ham0 Link encap:Ethernet HWaddr 7a:79:19:a5:e4:93 inet addr:25.165.228.147 Bcast:25.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:19ff:fea5:e493/64 Scope:Link inet6 addr: 2620:9b::19a5:e493/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:7743 errors:0 dropped:0 overruns:0 frame:0 TX packets:1250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:665642 (665.6 KB) TX bytes:204056 (204.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:41138 errors:0 dropped:0 overruns:0 frame:0 TX packets:41138 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6420962 (6.4 MB) TX bytes:6420962 (6.4 MB) wlan0 Link encap:Ethernet HWaddr 00:1e:64:45:fb:70 inet6 addr: fe80::21e:64ff:fe45:fb70/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:286999 errors:0 dropped:0 overruns:0 frame:0 TX packets:226966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:324386887 (324.3 MB) TX bytes:30674804 (30.6 MB) iwconfig : ham0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off sudo lshw -C network: *-network description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:45:fb:70 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-30-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:46 memory:c0400000-c0401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: c0 serial: c8:0a:a9:34:65:77 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:c0900000-c093ffff ioport:5000(size=128) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:19:a5:e4:93 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full ip=25.165.228.147 link=yes multicast=yes port=twisted pair speed=10Mbit/s lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: NVIDIA Corporation G98M [GeForce G 105M] (rev a1) 07:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak] 09:00.0 Ethernet controller: Qualcomm Atheros AR8131 Gigabit Ethernet (rev c0) rfkill list : 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 9: phy0: Wireless LAN Soft blocked: no Hard blocked: no any help will be REALLLYYYY appreciated

  Read the article

• How to install compat-drivers or compat-wireless

  - by Sasho

  Could someone please explain me in detail how to install some of this drivers. I am running Ubuntu 12.04.2 and have the infamous (as I see everywhere in the net) problem with Atheros AR9462 wifi card. I tried everything to fix it and compat drivers are the only solution that I haven't tried. I tried to install some random package from kernel.org site and it couldn't make the driver (it threw some error). Then I updated the kernel to 3.10-rc7 and downloaded the last release of compat drivers and again the same problem occured. I reinstalled Ubuntu 12.04.2 and now I am using the 3.5 kernel because I don't know if rc7 is stable version. So my question is which compat wireless or compat drivers to download for this kernel and what is the process of installing. I tried with some command from the repository and it returned that it's not found. PS I am new to Ubuntu and Linux in general so explaining at length the install process and which driver I should install would be appreciated.

  Read the article

• Downloads killing internet on my home network

  - by Travis

  I am currently having a problem with my wireless. Whenever I try to download anything it kills the internet for every other application(tabs within the same browser, browsers on other computers on the same network) except the process doing the download. This occurs with everything from downloading updates to iso's. I am not using a torrent. It happens when downloading upgrades, browser downloads, or anything else. This problem does not occur when I use Windows 7 on the same computer and it stops killing the internet for other computers if I turn the download/Ubuntu off. I am using an ASUS G74SX laptop running Ubuntu 12.10 with Gnome 3.6. My wireless card is an Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) Thanks!

  Read the article

• Troubleshooting wireless network connectivity

  - by taserian

  I'm currently running Ubuntu 10.10, and I'm running into trouble keeping my wireless connection alive. After rebooting, I get about 5-10 minutes of a good speed connection; afterwards, the connection just zeroes out. I've gotten around to stirring up a shell script that gives me another 10 minutes or so of connectivity. Script contents below: #! /bin/bash sudo ifconfig wlan0 up echo "Enabling wireless device . . ." sleep 5 sudo iwconfig wlan0 essid MyNetworkName echo "Connecting to network. . ." sleep 10 sudo dhclient wlan0 echo "Getting IP address. . ." sleep 5 echo "Done. Closing window. . ." sleep 5 Shortly after running the line "sudo iwconfig wlan0 essid MyNetworkName" from the script, I notice the speed pick up. Other computers in my home running Windows XP are not affected by this problem, so all indications point to my Ubuntu machine. Does anyone have any pointers as to how to resolve this?

  Read the article

• How to make ad-hoc network connection?

  - by Johan Nathaniel Soedjono

  I can't make ad-hoc from my netbook (Ubuntu 12.04). It has internet source from ethernet. I have tried making from network manager. But it always says 'Wireless Network Disconnected' and can't be detected by neither my other laptop nor my cell phone which have wifi. How can I make adhoc from it? I have already tried making a connection in Network Manager a lot of times, but it still can't connect and appear notification 'Wireless Network Disconnected'.

  Read the article

• Macbook Pro Wireless Reconnecting

  - by A Student at a University

  I'm using a WPA2 EAP network. I'm sitting next to the access point. The connection keeps dropping and taking ~10 seconds to reconnect. My other devices are staying online. What's causing it? syslog: 01:21:10 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:21:10 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX 01:21:10 NetworkManager[XX40]: <info> (eth1): DHCPv4 state changed reboot -> renew 01:21:10 NetworkManager[XX40]: <info> address XXX.XXX.XXX.XXX 01:21:10 NetworkManager[XX40]: <info> prefix 20 (XXX.XXX.XXX.XXX) 01:21:10 NetworkManager[XX40]: <info> gateway XXX.XXX.XXX.XXX 01:21:10 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:21:10 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:21:10 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:21:10 NetworkManager[XX40]: <info> domain name 'server.domain.tld' 01:21:10 dhclient: bound to XXX.XXX.XXX.XXX -- renewal in XXX seconds. 01:33:30 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:33:30 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX 01:33:30 dhclient: bound to XXX.XXX.XXX.XXX -- renewal in XXX seconds. 01:35:13 wpa_supplicant[XX60]: CTRL-EVENT-EAP-STARTED EAP authentication started 01:35:13 wpa_supplicant[XX60]: CTRL-EVENT-EAP-METHOD EAP vendor 0 method 25 (PEAP) selected 01:35:14 wpa_supplicant[XX60]: EAP-MSCHAPV2: Authentication succeeded 01:35:14 wpa_supplicant[XX60]: EAP-TLV: TLV Result - Success - EAP-TLV/Phase2 Completed 01:35:14 wpa_supplicant[XX60]: CTRL-EVENT-EAP-SUCCESS EAP authentication completed successfully 01:35:14 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> 4-way handshake 01:35:14 wpa_supplicant[XX60]: WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP] 01:35:14 NetworkManager[XX40]: <info> (eth1): supplicant connection state: 4-way handshake -> group handshake 01:35:14 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:35:17 wpa_supplicant[XX60]: CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys 01:35:17 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> disconnected 01:35:17 NetworkManager[XX40]: <info> (eth1): supplicant connection state: disconnected -> scanning 01:35:26 wpa_supplicant[XX60]: CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys 01:35:26 NetworkManager[XX40]: <info> (eth1): supplicant connection state: scanning -> disconnected 01:35:29 NetworkManager[XX40]: <info> (eth1): supplicant connection state: disconnected -> scanning 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 8 -> 3 (reason 11) 01:35:32 NetworkManager[XX40]: <info> (eth1): deactivating device (reason: 11). 01:35:32 NetworkManager[XX40]: <info> (eth1): canceled DHCP transaction, DHCP client pid XX27 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) starting connection 'Auto XXXXXXXXXX' 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 3 -> 4 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) scheduled... 01:35:32 NetworkManager[XX40]: <info> (eth1): supplicant connection state: scanning -> disconnected 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) started... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) scheduled... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) complete. 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) starting... 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 4 -> 5 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1/wireless): access point 'Auto XXXXXXXXXX' has security, but secrets are required. 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 5 -> 6 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) complete. 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) scheduled... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) started... 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 6 -> 4 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) scheduled... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) complete. 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) starting... 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 4 -> 5 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1/wireless): connection 'Auto XXXXXXXXXX' has security, and secrets exist. No new secrets needed. 01:35:32 NetworkManager[XX40]: <info> Config: added 'ssid' value 'XXXXXXXXXX' 01:35:32 NetworkManager[XX40]: <info> Config: added 'scan_ssid' value '1' 01:35:32 NetworkManager[XX40]: <info> Config: added 'key_mgmt' value 'WPA-EAP' 01:35:32 NetworkManager[XX40]: <info> Config: added 'password' value '<omitted>' 01:35:32 NetworkManager[XX40]: <info> Config: added 'eap' value 'PEAP' 01:35:32 NetworkManager[XX40]: <info> Config: added 'fragment_size' value 'XXX0' 01:35:32 NetworkManager[XX40]: <info> Config: added 'phase2' value 'auth=MSCHAPV2' 01:35:32 NetworkManager[XX40]: <info> Config: added 'ca_cert' value '/etc/ssl/certs/Equifax_Secure_CA.pem' 01:35:32 NetworkManager[XX40]: <info> Config: added 'identity' value 'XXXXXXX' 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) complete. 01:35:32 NetworkManager[XX40]: <info> Config: set interface ap_scan to 1 01:35:32 NetworkManager[XX40]: <info> (eth1): supplicant connection state: disconnected -> scanning 01:35:36 wpa_supplicant[XX60]: Associated with XX:XX:XX:XX:XX:XX 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: scanning -> associated 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-EAP-STARTED EAP authentication started 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-EAP-METHOD EAP vendor 0 method 25 (PEAP) selected 01:35:36 wpa_supplicant[XX60]: EAP-MSCHAPV2: Authentication succeeded 01:35:36 wpa_supplicant[XX60]: EAP-TLV: TLV Result - Success - EAP-TLV/Phase2 Completed 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-EAP-SUCCESS EAP authentication completed successfully 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: associated -> 4-way handshake 01:35:36 wpa_supplicant[XX60]: WPA: Could not find AP from the scan results 01:35:36 wpa_supplicant[XX60]: WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP] 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX:XX completed (reauth) [id=0 id_str=] 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: 4-way handshake -> group handshake 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:35:36 NetworkManager[XX40]: <info> Activation (eth1/wireless) Stage 2 of 5 (Device Configure) successful. Connected to wireless network 'XXXXXXXXXX'. 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) scheduled. 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) started... 01:35:36 NetworkManager[XX40]: <info> (eth1): device state change: 5 -> 7 (reason 0) 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Beginning DHCPv4 transaction (timeout in 45 seconds) 01:35:36 NetworkManager[XX40]: <info> dhclient started with pid XX87 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) complete. 01:35:36 dhclient: Internet Systems Consortium DHCP Client VXXX.XXX.XXX 01:35:36 dhclient: Copyright 2004-2009 Internet Systems Consortium. 01:35:36 dhclient: All rights reserved. 01:35:36 dhclient: For info, please visit https://www.isc.org/software/dhcp/ 01:35:36 dhclient: 01:35:36 NetworkManager[XX40]: <info> (eth1): DHCPv4 state changed nbi -> preinit 01:35:36 dhclient: Listening on LPF/eth1/XX:XX:XX:XX:XX:XX 01:35:36 dhclient: Sending on LPF/eth1/XX:XX:XX:XX:XX:XX 01:35:36 dhclient: Sending on Socket/fallback 01:35:36 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:35:36 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX 01:35:36 dhclient: bound to XXX.XXX.XXX.XXX -- renewal in XXX seconds. 01:35:36 NetworkManager[XX40]: <info> (eth1): DHCPv4 state changed preinit -> reboot 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 4 of 5 (IP4 Configure Get) scheduled... 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 4 of 5 (IP4 Configure Get) started... 01:35:36 NetworkManager[XX40]: <info> address XXX.XXX.XXX.XXX 01:35:36 NetworkManager[XX40]: <info> prefix 20 (XXX.XXX.XXX.XXX) 01:35:36 NetworkManager[XX40]: <info> gateway XXX.XXX.XXX.XXX 01:35:36 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:35:36 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:35:36 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:35:36 NetworkManager[XX40]: <info> domain name 'server.domain.tld' 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 5 of 5 (IP Configure Commit) scheduled... 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 4 of 5 (IP4 Configure Get) complete. 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 5 of 5 (IP Configure Commit) started... 01:35:37 NetworkManager[XX40]: <info> (eth1): device state change: 7 -> 8 (reason 0) 01:35:37 NetworkManager[XX40]: <info> (eth1): roamed from BSSID XX:XX:XX:XX:XX:XX (XXXXXXXXXX) to XX:XX:XX:XX:XX:XX (XXXXXXXXX) 01:35:37 NetworkManager[XX40]: <info> Policy set 'Auto XXXXXXXXXX' (eth1) as default for IPv4 routing and DNS. 01:35:37 NetworkManager[XX40]: <info> Activation (eth1) successful, device activated. 01:35:37 NetworkManager[XX40]: <info> Activation (eth1) Stage 5 of 5 (IP Configure Commit) complete. 01:35:43 wpa_supplicant[XX60]: Trying to associate with XX:XX:XX:XX:XX:XX (SSID='XXXXXXXXXX' freq=2412 MHz) 01:35:43 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> associating 01:35:43 wpa_supplicant[XX60]: Association request to the driver failed 01:35:46 wpa_supplicant[XX60]: Associated with XX:XX:XX:XX:XX:XX 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: associating -> associated 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: associated -> 4-way handshake 01:35:46 wpa_supplicant[XX60]: WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP] 01:35:46 wpa_supplicant[XX60]: CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX:XX completed (reauth) [id=0 id_str=] 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: 4-way handshake -> group handshake 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:40:47 wpa_supplicant[XX60]: WPA: Group rekeying completed with XX:XX:XX:XX:XX:XX [GTK=TKIP] 01:40:47 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> group handshake 01:40:47 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:50:19 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:50:19 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX

  Read the article

• how to find available wireless networks

  - by Quinn

  I'm using an HP Pavilion dv6000 I've looked at other answers similar to this question how ever when I look at my network symbol it doesn't say anything that the answer below says "Make sure that your wifi hardware switch is on or not. It is either F2 or F12 or near to it. Once the switch is enabled, there is a small fan-like applet on the top panel (Gnome Network Manager), fourth from the right. Click on it and if there is no tick mark on the option 'Enable Wireless', enable it. Wait till your wifi connection name appears." it how says 'Enable Networking' my wi-fi switch is on and I've tried using terminal to kill the applet as another answer suggests trying. Does anyone have any other ideas that might help? Just in case anybodies curious as to how I'm posting this I'm on my other ubuntu laptop that's running an older version.

  Read the article

• wireless repeater vs wireless bridge?

  - by Kossel

  Scenario: I have a ADSL modem inside the studio which is connected with some wired/wireless devices. but when I'm in the backyard with my laptop the wireless signal is very poor, so the connection is very unstable. I have an old belkin wireless router and I read that it can be useful in this scenario. after some search, it's compatible with DD-WRT, and seems setting it both wireless repeater or wireless bridge can do the job. but which is better for speed and stability or for my purpose they are the same? wireless repeater wireless bridge

  Read the article

• Configuration of the network manager via DBus: how to set the ad hoc mode

  - by Andrea

  I have an hard nut to crack: a nice bottle of italian Chianti wine to the solver! :) To automatically configure Wifi, I first have to kill the network manager and than activate the wifi via the commandline: I do this all automatically in my application and works great. However... it is not the right way to do this. As the user has no network gui anymore to configure some other network access. A much better and transparent way would be to configure wifi directly via network manager over the DBus interface. I was able to configure it, but I wasn't able to set it to ad hoc mode... Searching the web for a while: a lot about configuration in general but nothing related to ad hoc mode. I think the only way to do figure that out is to look into the source code of the network manager...maybe someone already did it and he can answer.

  Read the article

• Network Manager troubleshooting

  - by Anero

  I'm having some issues when connecting to my house's wifi from my Ubuntu 10.10 laptop. If the connection doesn't exists, when selecting the network (and after entering the WPA2 password) I'm able to connect. Once the connection is saved, when trying to reconnect, Network Manager works for a minute or so and then fails; the only way to reconnect then is to delete the saved connection and re-select the network from the list of available wireless networks. The same network works with no issues on the same laptop when running Win7, and on other wireless networks when running Ubuntu. Is there a Network Manager log which I can take a look at for troubleshooting the issue? Are there any tools for checking the wifi status?

  Read the article

• Intel Dual Band Wireless-AC 7260 keeps dropping wifi

  - by Rick T

  My wifi Intel Dual Band Wireless-AC 7260 keeps dropping wificonnection drops and the network to which I was connected disappears from the list of available networks in network manager. The only way to fix it is to disable wifi and re-enable it How can I fix this. I'm using ubuntu 14.04 64bit. It mostly drops connections on the 5ghz network. My other devices don't drop connections over wifi. see logs and versions rt@simon:~$ uname -a Linux simon 3.13.0-34-generic #60-Ubuntu SMP Wed Aug 13 15:45:27 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux rt@simon:~$ rt@simon:~$ dmesg | grep iwl [ 3.370777] iwlwifi 0000:03:00.0: irq 46 for MSI/MSI-X [ 3.381089] iwlwifi 0000:03:00.0: loaded firmware version 22.24.8.0 op_mode iwlmvm [ 3.414637] iwlwifi 0000:03:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144 [ 3.414695] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 3.414913] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 3.630208] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' [ 9.304838] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 9.305068] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 605.483174] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 605.483396] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S rt@simon:~$ cat /var/log/syslog | grep -e iwl -e 80211 | tail -n25 Aug 14 08:13:02 simon kernel: [ 3.452780] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:13:02 simon kernel: [ 3.630208] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' Aug 14 08:13:06 simon NetworkManager[1125]: <info> rfkill1: found WiFi radio killswitch (at /sys/devices/pci0000:00/0000:00:1c.2/0000:03:00.0/ieee80211/phy0/rfkill1) (driver iwlwifi) Aug 14 08:13:06 simon NetworkManager[1125]: <info> (wlan0): using nl80211 for WiFi device control Aug 14 08:13:06 simon NetworkManager[1125]: <info> (wlan0): new 802.11 WiFi device (driver: 'iwlwifi' ifindex: 3) Aug 14 08:13:06 simon kernel: [ 9.304838] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:13:06 simon kernel: [ 9.305068] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:14:18 simon kernel: [ 81.230162] cfg80211: Calling CRDA to update world regulatory domain Aug 14 08:14:18 simon kernel: [ 81.232330] cfg80211: World regulatory domain updated: Aug 14 08:14:18 simon kernel: [ 81.232332] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Aug 14 08:14:18 simon kernel: [ 81.232333] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232334] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232335] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232336] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232337] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:02 simon kernel: [ 605.483174] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:23:02 simon kernel: [ 605.483396] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:23:18 simon kernel: [ 621.223905] cfg80211: Calling CRDA to update world regulatory domain Aug 14 08:23:18 simon kernel: [ 621.228945] cfg80211: World regulatory domain updated: Aug 14 08:23:18 simon kernel: [ 621.228950] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Aug 14 08:23:18 simon kernel: [ 621.228954] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228956] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228959] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228961] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228963] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >